PLVW92U
Model:
PLVW92U
The Pyle ‘PLVW’ LCD Monitor Display Screens are universal and can be used in a wide variety of applications. Mount the
versatile video display in your vehicle, at home or in the office. They are perfect for custom installations and can be used for
convenient safety surveillance monitoring, vehicle media entertainment, as an optional second monitor expansion and more.
The slim-styled panel design allows for simple HD high-resolution video display ability wherever needed. Connect your system
using the inputs: (2) RCA video, (1) HDMI and (1) VGA connector; it also features RCA audio (L/R) connector jacks for
connection to an external sound system. Enjoy the convenience of widescreen HD video display with the Pyle ‘PLVW’
Universal Monitor Systems.
FRONT PANEL
1.MODE
Switch between the video inputs.
(HDMI, RCA1,RCA2, VGA)
2.Analog decrease
Forward select setting the items or
analog decrease menu.
3.MENU
Open the menu to adjust the units
display settings.
4.Analog increase
Backward select setting the items or
analog increase menu.
5.POWER
Turn the unit on and off.
6.IR
Remote control receiver.
WIRING
Please read this manual thoroughly.
Before using this product and keep
it well for future reference.
REMOTE
Power switch
HDMI/RCA/VGA switch
Menu
Analog increase
Analog decrease
MODE
IR
1 2 3 4 5 6
REMOTE CONTROL BATTERY
1. Always use new batteries when
relacing the old set.
2. Do not attempt to charge, short-circuit,
disassemble, heat or burn used batteries.
3. Battery replacement is necessary when remote
control acts sporadically or stops operating this device.
4. Do not place objects between the remote receiver.
5. If the monitor does not operate even when operating the
remote control from a close rangre, it is time to replace the
batteries product number:(CR2025)
Back of the remote
Battery tank
Battery
Transparent Slice
MENU OPERATION
Fuse Box
red line
DC 12V
Ground
V2 V1 L
R
black line
Audio (L/R)
Outputs
Video 1 Input
Video 2 Input
VGA
HDMI
Power supply do not meet the polarity, otherwise it will damage insurance tube.
(Fuse specifications: 3A or 5A)
VGA supported video modes: Maximum matching resolution 800 x 480pixel
HDMI supported video modes: 1080P/1080I/720P/480P/576P
visit www.PyleAudio.com for more information
Use the unit to achieve the desired
settings.
1.Press the MENU button on the unit to
bring up the on-screen picture control
menu.
2.Select the desired menu by pressing
the Remote left/right button on the unit
to choose BRIGHTNESS-CONTRASTHUE-SATURATION-LANGUAGESOURCE-RESET-EXIT. Press the
Remote MENU button to enter into the
control menu.
3.Adjust the current settings with the
left/right button on the unit, then press
the MENU button on unit to achieve
the desired settings and return to the
upper level of the menus.
Notice: in different mode menu is slightly
different, the actual shall prevail.
SPECIFICATIONS
Type :TFT LCD
PiXS:800x(R.G.B)x480
Display format: 16:9
System :PAL/NTSC
Dual Video Inputs
HDMI Input
VGA Input
Power Supply : DC 12V
Power consumption : ≤ 4.5 W
Operation temperature : 5℃~55℃
Storage temperature : -10℃~75℃
Model:
PLVW92U
Installation & Mounting
1. Drive mounting holes
10.315 inch
(262mm)
10.315 inch
(262mm)
According to the following size to draw a
cutting line on the wall, installed by digging
out a hole. The depth of the hole is larger
than 36MM.
7.283inch
(185mm)
Note: open hole, the level of attention, so
cannot be installed horizontally, and watch
If wires need to be placed in the hole,
increasing the depth of the hole.
6.772 inch
(172mm)
7.283 inch
(185mm)
2
1
7.874 inch(200mm)
8.819 inch(224mm)
2. Install the main
Connect the lines, place the subjects
in mounting hole, upper and lower
case-preserving Gap, then with 4
screws.
Screw specifications: 4mm X 12mm
or 4mm X (12+☆)mm
Note: the main level.
MATS (D 8mm)
push down
push down
3. Panel mounting
The display area is aligned with the position
of the panel in the frame body, a little hard
pressed to hang buckle at the surface of the
panel and the body fit.
Hang buckle
Note: the frame display area entirely within
the neat, well hang buckle clasp firmly.
push down
push down
4. Panel removal
4
3
2
1
Use a screwdriver or other flat tool, slightly
hard to pry the bottom right corner(part 1),
bottom right hang buckle will depart from the
main body of the Panel; Then use the same
method to open the panels hang buckle 2,3,4,
you can remove the Panel.
Note: when the top or bottom to pry, bigger
also can make up button broke off.
Warning: This product is a liquid crystal display, install and watch the position of the
horizontal line around, watch so as not to affect the image quality.
visit www.PyleAudio.com for more information
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising