Enjoy it. - Blaupunkt
CAR RADIO
AMSTERDAM 130
ADELAIDE 130
1 011 402 111 001
1 011 402 101 001
Enjoy it.
Operating and installation instructions
Controls
1
14
1
2
13
3
4
5
12
button
Unlock the detachable control panel
2 MENU button
Short press: Call up/close menu
Long press: Start scan function
3 On/Off button
Short press: Switch on car sound system
In operation: Mute car sound system (Mute)
Long press: Switch off car sound system
In the menu: Change menu level
In Fast-Browse mode: Confirm selection
4 Volume control
In the menu: Select menu item, change
setting
In Fast-Browse mode: Select folder and track
6
7
11
10
8
9 USB socket
: Front AUX-IN socket
; Keys 1 - 6
< Infrared receiver
= SRC button
Select memory bank or audio source
> DIS button
Short press: Switch display
Long press: Switch display brightness
? SD card slot (Adelaide 130 only)
Access only with detached control panel
6 Display
/ button
In the menu: Select menu item, change
setting
Radio mode: Start seek tuning
MP3/WMA mode: Change to next/previous
folder
/ button
In the menu: Change menu level
Radio mode: Adjust the stations
Other operating modes: Track selection
2
9
button (Eject) (Amsterdam 130 only)
Eject a CD
5 CD tray (Amsterdam 130 only)
7
8
15
Contents
Safety notes ...................................................... 4
Symbols used .............................................................. 4
Road safety .................................................................. 4
General safety notes ................................................. 4
Declaration of conformity ...................................... 5
Cleaning notes .................................................. 5
Disposal notes................................................... 5
Scope of delivery .............................................. 5
Optional equipment
(not part of the scope of delivery) ....................... 5
Placing the device in operation ....................... 5
Important note for radio reception
in the US and Asia...................................................... 5
Attaching/detaching the control panel ............ 5
Switching on/off ........................................................ 6
Volume .......................................................................... 6
Display brightness..................................................... 6
Switching demo mode on/off............................... 7
Traffic information ............................................ 7
Radio mode ....................................................... 7
RDS.................................................................................. 7
Changing to radio mode or selecting
a memory bank .......................................................... 7
Tuning into a station ................................................ 8
Storing stations or calling stored stations ........ 8
Scanning stations ...................................................... 8
Storing stations automatically
(Travelstore) ................................................................. 8
PTY .................................................................................. 9
Switching display....................................................... 9
Selecting a folder
(only in MP3/WMA mode) ....................................12
Fast searching ...........................................................12
Interrupting playback ............................................12
Scanning all tracks ..................................................12
Playing tracks in random order ..........................12
Repeatedly playing individual tracks or
directories ..................................................................12
Switching display.....................................................12
Browse mode ............................................................13
External audio sources ................................... 13
Front AUX-IN socket................................................13
Sound settings ................................................ 14
Calling and exiting the "AUDIO" menu ............14
Making settings in the "AUDIO" menu.............14
User settings ................................................... 15
Calling the user menu and selecting
a menu.........................................................................15
Making settings in the "TUNER" menu ............15
Making settings in the "DISPLAY" menu .........16
Making settings in the "VOLUME" menu ........17
Making settings in the "CLOCK" menu ............18
Making settings in the "VARIOUS" menu ........18
Factory settings .............................................. 19
Useful information ......................................... 20
Warranty .....................................................................20
Service .........................................................................20
Technical data ................................................. 20
Installation instructions ................................ 21
CD/MP3/WMA mode....................................... 10
Basic information .....................................................10
Changing to CD/MP3/WMA mode ....................10
Inserting/ejecting a CD
(Amsterdam 130 only) ...........................................10
Connecting/removing a USB data carrier .......11
Inserting/removing the memory card
(Adelaide 130 only) .................................................11
Selecting tracks ........................................................11
3
Safety notes
Safety notes
Road safety
The car sound system was manufactured according to the state of the art and established safety
guidelines. Even so, dangers may occur if you do
not observe the safety notes in these instructions.
These instructions contain important information to easily and safely install and operate the car
sound system.
• Read these instructions carefully and completely before using the car sound system.
• Keep the instructions at a location so that they
are always accessible to all users.
• Always pass on the car sound system to third
parties together with these instructions.
In addition, observe the instructions of the devices
used in conjunction with this car sound system.
Observe the following notes about road safety:
• Use your device in such a way that you can
always safely control your vehicle. In case of
doubt, stop at a suitable location and operate
your device while the vehicle is standing.
• Remove or attach the control panel only
while the vehicle is standing.
• Always listen at a moderate volume to protect your hearing and to be able to hear acoustic warning signals (e. g. police sirens). During
mute phases (e. g. when changing the audio
source), changing the volume is not audible.
Do not increase the volume during this mute
phase.
Symbols used
Observe the following notes to protect yourself
against injuries:
• Do not modify or open the device. The device
contains a Class 1 laser that can cause injuries
to your eyes (Amsterdam 130 only).
• Do not increase the volume during mute
phases, e. g. when changing the audio source.
Changing the volume is not audible during a
mute phase.
These instructions employ the following symbols:
DANGER!
Warns about injuries
CAUTION!
Warns about damaging the CD drive
DANGER!
Warns about high volume
The CE mark confirms the compliance
with EU directives.
쏅 Identifies a sequencing step
• Identifies a listing
4
General safety notes
Use as directed
This car sound system is intended for installation
and operation in a vehicle with 12 V vehicle system voltage and must be installed in a DIN slot.
Observe the performance limits in the technical
data. Repairs and installation, if necessary, should
be performed by a specialist.
Installation instructions
You may only install the car sound system yourself if you are experienced in installing car sound
systems and are very familiar with the electrical
system of the vehicle. For this purpose, observe
the installation instructions at the end of these
instructions.
Safety notes | Cleaning notes | Disposal notes | Scope of delivery | Placing the device in operation
Declaration of conformity
The Blaupunkt Europe GmbH declares that the
car sound system complies with the basic requirements and the other relevant regulations of the
directive 2004/108/EC.
The declaration of conformity can be found on the
Internet under www.blaupunkt.com.
Cleaning notes
Optional equipment
(not part of the scope of delivery)
Use only accessories approved by Blaupunkt.
Information is available from your Blaupunkt
specialised dealer or on the Internet under
www.blaupunkt.com.
Placing the device in operation
Solvents, cleaning and scouring agents as well as
dashboard spray and plastics care product may
contain ingredients that will damage the surface
of the car sound system.
• Use only a dry or slightly moistened cloth for
cleaning the car sound system.
• If necessary, clean the contacts of the control
panel regularly using a soft cloth moistened
with cleaning alcohol.
Attention
Transport securing screws
(Amsterdam 130 only)
Before the startup of the car sound system, ensure
that the transport securing screws are removed
(see the chapter "Installation instructions").
Disposal notes
This car sound system is designed for operation in
different regions with different frequency ranges
and station technologies. The factory default of
the reception area is "EUROPE". If you operate the
car sound system outside of Europe, e.g. in the US
or Asia, you first have to set a suitable reception
area in the menu. Available reception areas are
"EUROPE", "ASIA", "USA", "S-AMERICA" and "THAILAND".
The reception area for the radio reception is set
in the user menu (see the chapter "User settings",
section "Making settings in the "TUNER" menu",
menu item "AREA").
Do not dispose of your old unit in the household trash!
Use the return and collection systems available to
dispose of the old device.
Scope of delivery
The scope of delivery includes:
1 Car sound system
1 Operating/installation instructions
1 Case for the control panel
1 Support frame
1 Antenna connection adapter
2 Disassembly tools
1 Handheld remote control (incl. battery)
1 Connecting cable chamber A
1 Connecting cable chamber B
Important note for radio reception in
the US and Asia
Attaching/detaching the control
panel
The car sound system is equipped with a detachable control panel (release panel) to protect your
equipment against theft. In the delivery state,
the control panel is in the supplied case. To start
operating the radio after installation, you must
first attach the control panel (see the section
"Attaching the control panel" in this chapter).
5
Placing the device in operation
Always take the control panel with you when leaving the vehicle. The car sound system is worthless
to a thief without this control panel.
Caution
Damage to the control panel
Never drop the control panel.
Transport the control panel so that it is protected
against impacts and the contacts cannot become
dirty.
Do not expose the control panel to direct sunlight
or another heat source.
Avoid direct skin contact with the control panel's
electrical contacts.
Attaching the control panel
쏅 Push the control panel into the bracket at the
right edge of the device.
쏅 Push the control panel carefully into the left
bracket until it clicks into place.
Removing the control panel
쏅 Press the
button 1 to unlock the control
panel.
The left side of the control panel detaches
from the device and is secured by the bracket
against falling out.
쏅 Move the control panel slightly to the left
until it disengages from the right bracket.
쏅 Carefully remove the control panel from the
left bracket.
Note:
The car sound system automatically switches
off as soon as the control panel is removed.
Switching on/off
Switching on/off with the On/Off button
쏅 For switch-on, press the On/Off button 3.
The car sound system switches on.
쏅 To switch off the device, press and hold down
the On/Off button 3 for longer than 2 seconds.
6
The car sound system switches off.
Note:
If you switch on the car sound system while
the vehicle ignition is switched off, it automatically switches off after 1 hour to preserve
the vehicle battery.
Switching on/off via vehicle ignition
The car sound system will switch off/on simultaneously with the ignition if the device is correctly
connected to the vehicle's ignition as shown in the
installation instructions and you did not switch
the device off by pressing the On/Off button 3.
Volume
Adjusting the volume
You can adjust the volume in steps from 0 (off ) to
50 (maximum).
쏅 Turn the volume control 4 to change the
volume.
Note:
If a telephone is connected with the car sound
system as described in the installation instructions, the car sound system is muted in case
of a phone call. During muting, the display
shows "TELEPHONE".
Muting the car sound system (Mute)
쏅 Briefly press the On/Off button 3 to mute
the car sound system or to reactivate the previous volume.
During muting, the display shows "MUTE".
Display brightness
You can manually switch the display brightness
between daytime mode and night-time mode or
switch automatically with the driving lights of the
vehicle.
Notes:
• The manual or automatic switching of the
display brightness is selected in the user
menu (see the chapter "User settings",
section "Making settings in the "DISPLAY"
menu", menu item "DIM MODE").
Placing the device in operation | Traffic information | Radio mode
• The display brightness can be adjusted
separately for day and night (see the chapter "User settings", section "Making settings in the "DISPLAY" menu", menu items
"DIM DAY" and "DIM NIGHT".
쏅 Press the DIS button > for approx. 2 seconds
to manually switch the display brightness.
Switching demo mode on/off
The demo mode shows the functions of the car
sound system as scrolling text on the display. By
pressing any button, the demo mode is interrupted and you can operate the device.
The demo mode can be switched on and off in the
user menu (see the chapter "User settings", section
"Making settings in the "VARIOUS" menu", menu
item "DEMO MODE").
Traffic information
In the reception area "EUROPE", an FM station can
identify traffic reports by means of an RDS signal.
If priority for traffic reports is switched on, a traffic report is automatically switched through, even
if the car sound system is currently not in radio
mode.
If priority is switched on, the display shows the
). "TRAFFIC" is displayed
traffic jam symbol (
during a switched-through traffic announcement.
The priority is activated and deactivated in the
user menu (see the chapter "User settings", section "Making settings in the "TUNER" menu", menu
item "TRAFFIC").
Notes:
• The volume is increased for the duration
of the switched-through traffic announcement. You can adjust the minimum volume
for traffic announcements (see the chapter
"User settings", section "Making settings
in the "VOLUME" menu", menu item "TA
VOLUME").
• To cancel a switched-through traffic announcement, press the SRC button =.
Radio mode
RDS
Many FM stations broadcast an RDS (Radio Data
System) signal in addition to their programme
in the reception area "EUROPE" that allows the
following additional functions:
• The station name is shown on the display.
• The car sound system recognises traffic announcements and news broadcasts and can
automatically switch them through in other
operating modes (e. g. in CD mode).
• Alternate frequency: If RDS is activated, the car
sound system automatically selects the best
receivable frequency for the station that is currently set.
• Regional: At certain times, some radio stations divide their programme into regional
programmes providing different content. If
the REGIONAL function is activated, the car
sound system changes only to those alternate
frequencies on which the same regional programme is being broadcast.
The functions RDS and REGIONAL are activated
and deactivated in the user menu (see the chapter "User settings", section "Making settings in
the "TUNER" menu", menu items "RDS AF" and
"REGIONAL").
Changing to radio mode or selecting
a memory bank
쏅 Press the SRC button = repeatedly until the
desired memory bank is displayed:
FM1 씮 FM2 씮 FMT 씮 AM 씮 AMT
Notes:
• Up to 6 stations can be stored in each
memory bank.
• Memory banks can be activated or deactivated via the user menu (see the chapter
"User settings", section "Making settings in
the "TUNER" menu", menu item "BANDS"
(band selection)). Deactivated memory
banks are skipped during the source selection with the SRC button =
7
Radio mode
Tuning into a station
Scanning stations
There are various ways of tuning into a station:
With the scan function, you can scan either every
receivable station or the stored stations of the current waveband.
Tuning into stations manually
쏅 Briefly press the / button 7 once or
several times to change the frequency in increments, or long to quickly change the frequency.
Starting station seek tuning
쏅 Briefly press the / button 7 to start station seek tuning.
The radio tunes into the next receivable
station.
Notes:
• For the reception area "EUROPE": In the FM
waveband, only traffic information stations
are tuned into if the priority for traffic information (
) is switched on.
• For the reception areas "EUROPE" and
"USA": In the FM waveband, the next
station with the currently selected programme type is tuned into if the PTY function is activated (see the chapter "PTY").
• The sensitivity of seek tuning can be adjusted (see the chapter "User settings",
section "Making settings in the "TUNER"
menu", menu item "SEEK SENS").
Storing stations or calling stored
stations
쏅 Select the desired memory bank.
쏅 If necessary, set the desired station.
쏅 Press the station button 1 - 6 ; for approx.
2 seconds to store the current station under
the button.
- or 쏅 Briefly press the station button 1 - 6 ; to call
up the stored station.
8
Note:
You can adjust the scan time for each station (see the chapter "User settings", section
"Making settings in the "VARIOUS" menu",
menu item "SCAN TIME").
Scanning receivable stations
쏅 Press the MENU button 2 for approx. 2 seconds to start scanning.
During the scan, the display alternately displays "SCAN" and the current frequency as
well as memory bank or station name.
쏅 Briefly press the MENU button 2 to continue listening to the station that is currently
being received.
Scanning stored stations
쏅 Press the / button 7 for approx. 2 seconds to start scanning.
During the scan, the display shows the memory location and the current frequency or station name.
쏅 Briefly press the / button 7 to continue
listening to the station that is currently being
scanned.
Storing stations automatically
(Travelstore)
With Travelstore, you can automatically search
for and store the 6 stations offering the strongest
reception in the region in the FM and AM wavebands. The stations are stored in the FMT or AMT
memory bank. Any previously stored stations in
this memory bank are deleted in the process.
쏅 Select a memory bank of the desired waveband, e. g. FM1 or AM.
쏅 Press the SRC button = for approx. 2 seconds.
Radio mode
The tuner starts the automatic station seek
tuning; the display shows "FM TSTORE" or
"AM TSTORE". After the storing is completed,
the radio plays the station at memory location
1 of the FMT or AMT level.
Notes:
• For the reception area "EUROPE": If the
priority for traffic information is switched
), only traffic information stations
on (
are stored.
• If the FMT or AMT memory bank is deactivated (see the chapter "User settings",
section "Making settings in the "TUNER"
menu", menu item "BANDS"), it is automatically reactivated if you initiate the
Travelstore function.
PTY
In the reception areas "EUROPE" and "USA", an
FM station can transmit its current programme
type, e. g. CULTURE, POP, JAZZ, ROCK, SPORT or
SCIENCE. Hence, the PTY function allows a targeted search for broadcasts of a certain programme
type, e. g. for rock or sports broadcasts. Note that
PTY is not supported by all stations.
Note:
The PTY function is only available if it has been
activated (see the chapter "User settings", section "Making settings in the "TUNER" menu",
menu item "PTY").
Selecting a programme type
To select a programme type read the section
"Making settings in the "TUNER" menu", menu
item "PTY TYPE" in the chapter "User settings".
Note:
You can set the language in which the programme types should be displayed (see the
chapter "User settings", section "Making settings in the "TUNER" menu", menu item "PTY
LANG").
Searching for stations
쏅 Press the / button 7.
During the seek tuning, the currently selected
programme type is shown on the display.
As soon as a station with the desired programme type is found, it remains being tuned
into.
Notes:
• If no station with the selected programme
type is found, "PTY NONE" is briefly displayed and 2 beeps can be heard. The
radio will then retune to the station that it
played last.
• If the tuned radio station or another station on the broadcasting network broadcasts your selected programme type at a
later point in time, the car sound system
will automatically switch from the currently tuned station or from the current
audio source (e. g. CD) to the station whose
programme type matches the one you selected. Note that this function is not supported by all stations.
Switching display
쏅 Press the DIS button > to toggle between
these displays:
Display
ABCDEF
FM1 102.90
or
P1 102.90
FM1 18:30
or
P1
18:30
Meaning
Station name
Memory bank/frequency
or
Memory location/frequency
Memory bank/time
or
Memory location/time
9
CD/MP3/WMA mode
CD/MP3/WMA mode
Basic information
Amsterdam 130:
This car sound system can be used to play audio
CDs (CDDA) and CD-R/RWs with audio, MP3 or
WMA files as well as MP3 or WMA files on USB data
carriers.
Adelaide 130:
This car sound system can be used to play MP3 or
WMA files on USB data carriers and SD(HC)/MMC
memory cards.
Notes:
• To ensure proper functioning, use only CDs
with the Compact-Disc logo.
• Blaupunkt cannot guarantee the flawless
function of copy-protected CDs and all
CD blanks, USB data carriers and memory
cards available on the market.
Note the following information when preparing
an MP3/WMA data carrier:
• Naming of tracks and directories:
– Max. 32 characters without the file extension ".mp3" or ".wma" (the use of more
characters reduces the number of tracks
and folders that the car sound system can
recognise)
– No umlauts or special characters
• CD formats: CD-R/RW, Ø: 12 cm
• CD data formats: ISO 9669 Level 1 and 2, Joliet
• CD burn speed: Max. 16x (recommended)
• USB format/file system: Mass storage device /
FAT16/32
• Memory card file system: FAT16/32
• File extension of audio files:
– .MP3 for MP3 files
– .WMA for WMA files
• WMA files only without Digital Rights Management (DRM) and created with Windows Media
Player version 8 or later
• MP3 ID3 tags: Version 1 and 2
10
• Bitrate for creating audio files:
– MP3: 32 to 320 kbps
– WMA: 32 to 192 kbps
• Maximum number of files and directories: Up
to 20,000 entries depending on the data structure
Changing to CD/MP3/WMA mode
쏅 Press the SRC button = repeatedly until the
desired audio source is displayed:
• "CD" (Amsterdam 130 only): Inserted CD
• "SD(HC)" (Adelaide 130 only): Inserted
memory card
• "USB": Connected USB data carrier
• "AUX": Connected external audio source
Notes:
• The respective audio source can be selected only if a corresponding CD is inserted or
a corresponding device is connected.
• If the car sound system first has to read
the data of a connected device or data carrier before the playback, the display shows
"READING". The duration of the reading
depends on the data volume and design of
the device or data carrier. If the device or
data carrier is defective or the transferred
data cannot be played back, a corresponding message appears on the display (e. g.
"USB ERROR").
Inserting/ejecting a CD
(Amsterdam 130 only)
Inserting a CD
Risk of severe damage to the CD
drive!
Noncircular contoured CDs (shape CDs)
and CDs with a diameter of 8 cm (mini CDs) must
not be used.
We accept no responsibility for any damage to the
CD drive that may occur as a result of the use of
unsuitable CDs.
CD/MP3/WMA mode
Note:
You must not hinder or assist the drive as it
automatically draws in the CD.
쏅 Insert the CD with its printed side up into the
CD tray 5 until you feel a slight resistance.
The drive automatically draws in the CD and
checks its data. Afterwards, the playback
starts in CD or MP3 mode.
Note:
If the inserted CD cannot be played back, "CD
ERROR" is briefly displayed and the CD is automatically ejected after approx. 2 seconds.
Ejecting a CD
Note:
You must not hinder or assist the drive as it
ejects the CD.
쏅 Press the button 8 to eject an inserted
CD.
Notes:
• If a CD is ejected and not removed, the
drive will automatically draw it back in
again after approx. 10 seconds.
• You can also eject CDs while the car sound
system is switched off or whilst another audio source is activated.
Connecting/removing a USB data
carrier
Connecting a USB data carrier
쏅 Switch off the car sound system so that the
data carrier will be correctly registered.
쏅 Pull the protective cap of the USB socket 9
to the front until it moves out of the socket
and fold it down.
쏅 Connect the USB data carrier.
쏅 Turn on the car sound system.
If the USB data carrier is initially selected as
audio source, the data are read first.
Notes:
• If the connected USB data carrier cannot
be seen, "USB ERROR" is briefly displayed.
• The time required for reading in the data
depends on the design and size of the USB
data carrier.
Removing a USB data carrier
쏅 Switch off the car sound system so that the
data carrier will be correctly unregistered.
쏅 Disconnect the USB data carrier.
쏅 Close the protective cap of the USB socket 9.
Inserting/removing the memory card
(Adelaide 130 only)
Inserting the memory card
쏅 Detach the control panel.
쏅 Insert the memory card with its labelled side
up and its contacts first into the card slot ?
until it clicks into place.
쏅 Attach the control panel.
After switch-on, the device automatically
selects the inserted memory card as audio
source. The data of the memory card are being read. Afterwards, the playback starts in
MP3 mode.
Notes:
• If the inserted memory card cannot be
played, "SD ERROR" is briefly displayed.
• The time required for reading the card
depends on the design and size of the
memory card.
Removing the memory card
쏅 Detach the control panel.
쏅 Push on the memory card until it disengages.
쏅 Pull the memory card out of the card slot ?.
쏅 Attach the control panel.
Selecting tracks
쏅 Press the / button 7 briefly to change
to the previous/next track.
Note:
If the current track plays longer than 3 seconds, pressing 7 once restarts the track.
11
CD/MP3/WMA mode
Selecting a folder
(only in MP3/WMA mode)
Repeatedly playing individual tracks
or directories
쏅 Press the / button 7 briefly to change
to the previous/next folder.
쏅 Press the 3 RPT button ; to change among
the playback modes:
Fast searching
쏅 Press and hold down the / button 7
until the desired position has been reached.
Interrupting playback
쏅 Press the 2
button ; to interrupt the
playback ("PAUSE") or to continue it.
Scanning all tracks
The scan function scans all available tracks.
쏅 Press the MENU button 2 for approx. 2 seconds to start the scan, or briefly to continue
playing the currently scanned track.
Note:
The scan time can be adjusted (see the chapter "User settings", section "Making settings
in the "VARIOUS" menu", menu item "SCAN
TIME").
Playing tracks in random order
쏅 Press the 4 MIX button ; to change among
the playback modes:
Operation Display
CD*
MIX ALL
MP3/
WMA
Gen.
MIX DIR
MIX ALL
MIX OFF
Meaning
Mixing tracks
Mixing tracks of
the current folder
Mixing tracks of
the data carrier
Regular playback
* Amsterdam 130 only
If the MIX function is switched on, the icon
MIX (mix all tracks) or MIX
(mix tracks of
current folder) is shown on the display.
Operation Display
CD*
RPT TRACK
RPT TRACK
MP3/
WMA
RPT DIR
Gen.
RPT OFF
Meaning
Repeating tracks
Repeating tracks
Repeating
folders
Regular playback
* Amsterdam 130 only
If the RPT function is switched on, the icon
(repeat tracks) or
(repeat
folders) is shown on the display.
Switching display
쏅 Press the DIS button > once or several times
to switch among these displays:
Operation
Display
T01 00:15
CD*
T01 03:37
T01 18:30
MP3/
WMA
FILE
FOLDER
SONG
ARTIST
ALBUM
PLAY 00:15
TOTAL03:37
CLOCK18:30
ALL INFO
Meaning
Track number
and playing time
Track number
and duration
Track number
and time
File name
Folder name
Track name**
Artist**
Album name**
Playing time
Track duration
Time
All information
as scrolling text
* Amsterdam 130 only
** Track name, artist and album name must be
stored as ID3 tag to be able to display them.
12
CD/MP3/WMA mode | External audio sources
Browse mode
In Browse mode, you can directly search for and
select a certain track on the MP3/WMA data carrier
without interrupting the current playback.
Calling the browse mode
쏅 Press the 1 button ; to call up the browse
mode.
The icon flashes on the display. In addition,
the icon
(folder) or icon (track) appears.
The first or current folder on the data carrier is
being displayed.
Notes:
• The first folder is displayed only if the
browse mode has been called for the first
time after inserting or connecting the data
carrier. Afterwards, the current folder is
displayed whenever the browse mode is
called.
• You can exit the browse mode at any time
by pressing the 1 button ;.
쏅 Press the / button 7 once or several
times or hold the button pressed to select a
different folder.
쏅 Press the button 7 to display the tracks of
the selected folder.
The first track of the folder is shown on the
display.
Note:
Pressing the button 7 returns you to the
folder list.
쏅 Press the / button 7 once or several
times or hold the button pressed to select a
different track.
쏅 Press the button 7 to play the track.
The playback starts. You are exiting the
browse mode.
Fast browsing
Fast browsing enables faster access to tracks. Instead of the arrow keys 7, you use the volume
control 4 and the On/Off button 3 to select
and confirm list entries:
Function
Selecting
entries in lists
Confirming
entries
Return to the
higher level
Browse
mode
7
/
7
Fast browse
mode
Volume
control 4
On/off
button 3
7
7
Fast browsing is switched on or off in the user
menu (see the chapter "User settings", section
"Making settings in the "VARIOUS" menu", menu
item "BROWSE").
Note:
With activated fast browsing, you cannot
change the volume in browse mode or mute
the car sound system. To do so, first exit the
browse mode by pressing the button 1 ;
or starting the track playback.
External audio sources
Front AUX-IN socket
Danger!
Increased risk of injury from
connector.
In case of an accident, the protruding connector
in the front AUX-IN socket may cause injuries. The
use of straight plugs or adapters leads to an increased risk of injury.
For this reason, it is recommended to use angled
jack plugs.
As soon as an external audio source, such as a
portable MP3 player is connected to the front
AUX-IN socket :, it can be selected with the SRC
button =. "AUX" then appears on the display.
13
Sound settings
Sound settings
The following sound settings can be changed in
the "AUDIO" menu:
• Adjusting bass and treble
• Setting the left/right volume distribution
(Balance) or front/rear (Fader)
• Adjusting the increase of bass at low volume
(X-Bass)
• Selecting a sound profile (Presets)
• Adjusting the time delay for switching in an
external amplifier
Calling and exiting the "AUDIO"
menu
쏅 Briefly press the MENU 2 button to open
the user menu.
쏅 Turn the volume control 4 until the "AUDIO"
menu item is selected.
쏅 Press the On/Off button 3 to open the
"AUDIO" menu.
쏅 Turn the volume control 4 until the desired
menu item is selected.
쏅 Perform the setting (see the next section).
쏅 Briefly press the MENU button 2 to exit the
menu.
Notes:
• The menu is automatically exited approx.
16 seconds after the last button activation
and you are returned to the display of the
current audio source.
• In the menu, you can press the button
7 in each case to return to the higher
menu level.
• The menu does not allow changing the
volume or muting (Mute) the car sound
system.
14
Making settings in the "AUDIO"
menu
BASS
Bass level. Settings: –7 to +7.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 until the desired
level is set.
TREBLE
Treble. Settings: –7 to +7.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 until the desired
level is set.
BALANCE
Left/right volume distribution. Settings: L9 (left)
to R9 (right).
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 until the desired
volume distribution is set.
FADER
Front/rear volume distribution. Settings: R9 (rear)
to F9 (front).
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 until the desired
volume distribution is set.
X-BASS
Increase of bass at low volume. Settings: ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
Sound settings | User settings
PRESETS
Selecting equalizer presettings. Settings: POP,
ROCK, CLASSIC, EQ OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
AMP DELAY
Setting the delay with which a connect amplifier
is switched in. Settings: 0.5/1.0/1.5/2.0/2.5 seconds
and OFF (no delay).
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 until the desired
delay is set.
User settings
Calling the user menu and selecting
a menu
쏅 Briefly press the MENU 2 button to open
the user menu.
In the user menu, the user settings can be found in
the following menus:
• TUNER
• AUDIO (see chapter "Sound settings")
• DISPLAY
• VOLUME
• CLOCK
• VARIOUS
쏅 Turn the volume control 4 until the desired
menu is selected.
쏅 Press the On/Off button 3 to open the
selected menu.
쏅 Turn the volume control 4 until the desired
menu item is selected.
쏅 Perform the setting (see the following sections).
쏅 Briefly press the MENU button 2 to exit the
menu.
Notes:
• The menu is automatically exited approx.
16 seconds after the last button activation
and you are returned to the display of the
current audio source.
• In the menu, you can press the button
7 in each case to return to the higher
menu level.
• The menu does not allow changing the
volume or muting (Mute) the car sound
system.
Making settings in the "TUNER"
menu
TRAFFIC (traffic information)
(only for reception area EUROPE)
Only possible in FM radio mode: Switching priority for traffic announcements on or off. Settings:
ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
If priority is switched on for traffic information, the
.
display shows the icon
BANDS (band selection)
Activating or deactivating memory banks. Memory
banks that can be deactivated: FM2, FMT, AM, AMT.
쏅 Press the On/Off button 3 to open the
menu.
쏅 Turn the volume control 4 until the desired
memory bank is displayed.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to toggle between the settings ON (activate memory
bank) and OFF (deactivate memory bank).
Deactivated memory banks are skipped during
the source selection with the SRC button =.
Note:
If a memory bank is deactivated, the stations
stored in this memory bank are retained.
15
User settings
REGIONAL
(only for reception area EUROPE)
Only possible in FM radio mode: Switching
REGIONAL function on or off. Settings: ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
SEEK SENS
Setting the sensitivity of station seek tuning. Settings: LOW, HIGH.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
RDS AF
Switching the RDS function on or off. Settings: ON,
OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
Note:
If the reception area "ASIA", "USA", "S-AMERICA"
or "THAILAND" is selected, RDS is automatically switched off. The station name continues
to be shown on the display.
PTY
(only for reception areas EUROPE and USA)
Switching the PTY function on or off. Settings: ON,
OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
16
PTY TYPE
Only possible with activated PTY function: Select
a programme type.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the available programme types.
PTY LANG
Only possible with activated PTY function: Select
the language for the display of the programme
types. Settings: ENGLISH, DEUTSCH (German),
FRANCAIS (French).
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the languages.
AREA (reception area)
Select the reception area for the radio reception.
Settings: EUROPE, ASIA, USA, S-AMERICA, THAILAND.
쏅 Press the On/Off button 3 to open the
menu.
쏅 Turn the volume control 4 to change between the reception areas.
쏅 Press the On/Off button 3 to select a reception area.
The display shows "PRESS > TO CONFIRM".
button 7 to confirm the
쏅 Press the
selected reception area.
Making settings in the "DISPLAY"
menu
DIM MODE
Select automatic or manual switching of the display brightness for day or night. Settings: AUTO
(display brightness is automatically switched by
switching the driving lights on or off ), MAN (display brightness can be switched manually).
쏅 Press the On/Off button 3 to change the
setting.
User settings
쏅 Turn the volume control 4 to change between the settings.
Automatic switching of the display brightness is
possible only If your car sound system is installed
as described in the installation instructions and
your vehicle features the corresponding connection.
DIM DAY/DIM NIGHT
Setting the display brightness for the day (DIM
DAY) or the night (DIM NIGHT). Settings: 1 – 16.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to set the desired
display brightness.
SCROLL
Select the display of scrolling text (e. g. when
displaying MP3 file names) either as single display
or continued display. Settings: 1X (single display),
ON (continued display).
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
Making settings in the "VOLUME"
menu
ON VOLUME
Setting the power-on volume. Settings: 1 – 50.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to set the desired
power-on volume.
LAST VOL
If you select the setting LAST VOL, every time you
switch on the radio, the volume level that was set
the last time you switched the radio off is activated
again. Settings: ON, OFF.
Danger!
High volume
The power-on volume can be unexpectedly high if the LAST VOL setting is selected
and a high volume was set the last time the radio
was switched off.
Always set the device to a moderate volume.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
TA VOLUME (traffic announcement volume)
(only for reception area EUROPE)
Setting the minimum volume for traffic announcements. Settings: 1 – 50.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to set the volume.
BEEP
Switching the confirmation beep on or off. Settings: ON, OFF.
Note:
When storing radio stations, a confirmation beep sounds even if the OFF setting is
selected.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
17
User settings
Making settings in the "CLOCK"
menu
CLK DISP
Switch the permanent display of the time on or off.
Settings: ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
If the permanent display of the time is switched
on, the time is shown on the display. The display
of the respective audio source is shown only after
pressing a button. Approximately 16 seconds after
the button is pressed last, the time is displayed
again.
HOUR MODE
Selecting the 12 or 24-hour time. Settings: 12, 24.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
SET CLOCK
Setting the time.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 counterclockwise
to set the hours.
쏅 Turn the volume control 4 clockwise to set
the minutes.
Note:
When you set the time in 12-hour mode
(MODE 12H), an "A" is displayed before the
time for the time before noon or a "P" for the
time after noon.
18
RDS CLOCK (automatic time setting)
(only for reception area EUROPE)
Switching automatic clock setting with clock data
transmitted via RDS on or off. Settings: ON, OFF.
Note:
The time set with the clock data may not be
correct, even if an RDS station is being received.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
Making settings in the "VARIOUS"
menu
DEMO MODE
Switching the demo mode on or off. Settings:
ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
In demo mode, the features of the radio are shown
as scrolling text on the display.
BROWSE
Switching fast track selection in browse mode on
or off using the volume control 4 and the On/Off
button 3. Settings: ON, OFF.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
SCAN TIME
Setting the scan time in seconds. Settings:
4/8/12/16/60 seconds.
쏅 Press the On/Off button 3 to change the
setting.
쏅 Turn the volume control 4 to change between the settings.
User settings | Factory settings
SWC (Steering Wheel Control configuration)
Configuring the buttons of a connected steering
wheel control.
쏅 Press the On/Off button 3 to open the
menu.
쏅 Turn the volume control 4 to change between the functions.
쏅 Press the On/Off button 3 to select a function.
쏅 Press the corresponding button on the steering wheel control for approx. 1 second to program the button with the selected function.
VERSION
Displaying the version of the CPU and software of
the radio.
쏅 Press the On/Off button 3 to open the
menu.
쏅 Turn the volume control 4 to toggle between the display of the version number of
CPU (P) and software (E).
NORMSET
Restoring the original factory settings of the car
sound system.
쏅 Press the On/Off button 3.
The display shows "PRESS > TO CONFIRM".
쏅 Press the button 7 to confirm the resetting.
The car sound system switches off and is reset to the factory settings. If a CD has been
inserted in the CD drive, the car sound system
automatically switches on again (Amsterdam
130 only).
Factory settings
Important factory settings in the user menu:
Menu item
AREA
FM2 / FMT / AM / AMT
RDS AF*
REGIONAL*
TRAFFIC*
SEEK SENS
PTY**
ON VOLUME
TA VOLUME*
BEEP
BROWSE
SCAN TIME
DIM MODE
HOUR MODE
SET CLOCK
Factory setting
EUROPE
ON
ON
OFF
OFF
HIGH
OFF
20
20
ON
ON
8SEC
MAN
24H
00:00
* Only in reception area "EUROPE"
** Only in reception areas "EUROPE" and "USA"
In the user menu, you can restore the original
factory settings of the car sound system (see the
chapter "User settings", section "Making settings
in the "VARIOUS" menu", menu item "NORMSET").
19
Useful information | Technical data
Useful information
Warranty
We provide a manufacturer's warranty for products bought within the European Union. For devices purchased outside the European Union, the
warranty terms issued by our respective responsible domestic agency are valid. The warranty terms
can be called up from www.blaupunkt.com.
Wavebands in South America:
FM:
87.5 – 107.9 MHz
AM:
530 – 1,710 kHz
FM frequency response: 30 – 15,000 Hz
CD (Amsterdam 130 only)
Frequency range:
20 – 20,000 Hz
Pre-amp out
2 channels:
2V
In some countries, Blaupunkt offers a repair and
pick-up service.
Information about the availability of this service in
your country can be found at www.blaupunkt.com.
If you want to take advantage of this service, you
may request a pick-up service for your car sound
system via the Internet.
Input sensitivity
Front AUX-IN:
300 mV / 10 kΩ
Technical data
Weight:
Amsterdam 130:
Adelaide 130:
Service
Voltage supply
Operating voltage:
10.5 – 14.4 V
Dimensions and weight
W x H x D (incl. antenna connection adapter):
Amsterdam 130:
178 x 52 x 170 mm
Adelaide 130:
178 x 52 x 116 mm
Current consumption
In operation:
< 10 A
10 sec. after switch-off: < 3.5 mA
Amplifier
Output power:
4 x 22 watts sine
at 14.4 V at 4 ohms.
4 x 50 watts max. power
Tuner
Wavebands in Europe/Asia/Thailand:
FM:
87.5 – 108 MHz
AM:
531 – 1,602 kHz
Wavebands in the US:
FM:
AM:
87.7 – 107.9 MHz
530 – 1,710 kHz
Subject to changes
20
approx. 1.55 kg
approx. 0.79 kg
Installation instructions
Installation instructions
Safety instructions
When carrying out installation work and
making connections please observe the following
safety instructions:
• Disconnect the negative terminal of the battery! When doing so, please observe the vehicle manufacturer’s safety instructions.
• Make sure you do not damage vehicle components when drilling any holes.
• The cross sections of the positive and negative
cables must not be less than 1.5 mm².
• Do not connect the vehicle’s plug connectors to the radio!
You can obtain the adapter cable required
for your vehicle type from any BLAUPUNKT
dealer.
• Depending on the model, your vehicle may
differ from the description provided here. We
accept no responsibility for any damages due
to incorrect installation or connection or for
any consequential damages.
If the information provided here is not suitable for your specific installation requirements,
please contact your Blaupunkt dealer, your vehicle manufacturer or our telephone hotline.
When installing an amplifier, you must first connect the device earth connections before connecting the plugs for the line-out jacks.
Earth connection of external devices may not
be connected to earth of car sound system
(housing).
21
Installation instructions
Supplied mounting hardware
Available as an optional accessory
7 607 621 …
Installation kits
7 608 … …
22
Installation instructions
1.
4.
Steering wheel
remote control
GND
SWC-2
SWC-1
Antenna
connection
12V
2. Amsterdam 130 only
Antenna
Preamp out
(2 channels)
5.
182
165
53
3.
1-20
0° - 30°
+/– 10°
+/– 10°
23
Installation instructions
6. Removal
7.
1.
12V
2.
1.
2.
3.
24
Installation instructions
A
1
2
3
4
5
6
7
8
*
NC
Telephone Mute
NC
Permanent +12V
Auto antenna*
Illumination
Kl.15/Ignition
Ground
B
1
2
3
4
5
6
7
8
Speaker out RR+
Speaker out RR–
Speaker out RF+
Speaker out RF–
Speaker out LF+
Speaker out LF–
Speaker out LR+
Speaker out LR–
Switched power supply +12 V / max. 150 mA
25
Installation instructions
Relais
+12V
7
1 35
Kl. 15 +12V
6 8
2 4
Telephone Mute
4 ohms
4 ohms
4 ohms
4 ohms
Subject to changes!
26
+12V
12V
Please keep the filled-in radio pass in a safe place!
This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such
technology outside of this product is prohibited without a license from Microsoft.
© 2013 All rights reserved by Blaupunkt. This material may be reproduced, copied or distributed for
personal use only.
27
Passport
Name:
......................................................................................................................
Type:
......................................................................................................................
Serial no.:
BP ...............................................................................................................
1 011 402 _ _ _ 001
Blaupunkt Europe GmbH
Robert-Bosch-Straße 200
D-31139 Hildesheim
http://www.blaupunkt.com
03/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising