Model Name: P270HVN01.0

Model Name: P270HVN01.0
P270HVN01.0 Product Specification
Rev.0.0
Model Name: P270HVN01.0
Issue Date : 2012/11/30
(Ϡ
Ϡ)Preliminary Specifications
( )Final Specifications
Customer Signature
Date
AUO
Date
Approval By PM Director
Approved By
Paley Fang
_________________________________
Note
____________________________________
Reviewed By RD Director
Center Chen
____________________________________
Reviewed By Project Leader
John Shih
____________________________________
Prepared By PM
Rafael Lu
____________________________________
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
1
P270HVN01.0 Product Specification
Rev.0.0
Contents
No
CONTENTS
RECORD OF REVISIONS
1
GENERAL DESCRIPTION
1-1
GENERAL INFORMATION
2
OPTICAL CHARACTERISTICS
3
MECHANICAL CHARACTERISTICS
4
FUNCTIONAL BLOCK DIAGRAM
5
ABSOLUTE MAXIMUM RATINGS
5-1
TFT LCD MODULE
5-2
BACKLIGHT UNIT
5-3
ABSOLUTE RATINGS OF ENVIRONMENT
6
ELECTRICAL CHARACTERISTICS
6-1
TFT LCD MODULE
6-2
BACKLIGHT UNIT
7
SIGNAL CHARACTERISTICS
7-1
PIXEL FORMAT DEFINITION
7-2
INPUT DATA FORMAT DEFINITION
7-3
SIGNAL DESCRIPTION
7-4
TIMING CHARACTERISTICS
7-5
TIMING DIAGRAM
7-6
POWER ON/OFF SEQUENCE
8
9
CONNECTOR AND PIN ASSIGNMENT
8-1
TFT LCD MODULE
8-2
PIN ASSIGNMENT
RELIABILITY TEST
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
2
P270HVN01.0 Product Specification
Rev.0.0
10
SHIPPING LABEL
11
MECHANICAL CHARACTERISTICS
12
PACKING SPECIFICATION
13
12-1
PACKING FLOW
12-2
PALLET AND SHIPMENT INFORMATION
PRECAUTIONS
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
3
P270HVN01.0 Product Specification
Rev.0.0
Record of Revision
Version
Date
0.0
2012/11/30
Page
Description
First release
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
4
P270HVN01.0 Product Specification
Rev.0.0
1. General Description
This specification applies to the 27 inch-FHD color a-Si TFT-LCD Module P270HVN01.0. The display supports the FHD
- 1920(H) x 1080(V) screen format and 16.7M colors (RGB 8-bit data). The light source of this TFT-LCD module is
W-LED. All input signals are 2-channel LVDS interface and this module doesn’t contain a driver for backlight.
1.1 General Information
The following items are characteristics summary on the table under 25°C condition:
Items
Screen Diagonal
Unit
[mm]
Specification
685.65(27.0”)
Active Area
[mm]
597.6 (H) x 336.15 (V)
Pixels H x V
Pixel Pitch
1920(x3) x 1080
[um]
311.25 (per one triad) ×311.25
Pixel Arrangement
R.G.B. Vertical island
Display Mode
White Luminance ( Center )
VA Mode, Normally Black
2
2
[cd/m ]
300 cd/m (Typ.)
Contrast Ratio
3000 (Typ.)
Optical Response Time
[msec]
12ms (Typ., on/off)
Nominal Input Voltage VDD
[Volt]
5 V (Typ)
Power Consumption
(VDD line + LED line)
Weight
Physical Size
[Watt]
26.88 watt
VDD line : PDD (typ), All white pattern at 60Hz = 5.1 W
LED line : PBLU (typ) = 21.78 W
[g]
2180 gram (Typ.)
[mm]
613.6(H)x356.85(V)x10.0(D)
Electrical Interface
Dual channel LVDS
Support Color
16.7M colors (RGB 8-bit)
Surface Treatment
Anti-Glare 3H
Temperature Range
Operating
[°C]
0 to +50
Storage (Shipping)
[°C]
-20 to +60
RoHS Compliance
RoHS Compliance
TCO Compliance
TCO 6.0 Compliance
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
5
(Typ.)
P270HVN01.0 Product Specification
Rev.0.0
2. Optical Characteristics
The optical characteristics are measured under stable conditions at 25°C:
Item
Unit
Conditions
Min.
Typ.
Max.
150
178
-
150
178
-
1800
3000
-
Raising Time (TrR)
-
7
-
Falling Time (TrF)
-
5
-
Raising + Falling
-
12
-
Red x
0.615
0.645
0.675
Red y
0.300
0.330
0.360
Green x
0.285
0.315
0.345
Green y
0.590
0.620
0.650
Blue x
0.124
0.154
0.184
Blue y
0.034
0.064
0.094
White x
0.283
0.313
0.343
White y
[cd/m ]
0.299
240
0.329
300
0.359
-
6
Luminance Uniformity
[%]
75
80
-
7
Crosstalk (in 60Hz)
[%]
1.5
8
Flicker
dB
-20
9
Horizontal
CR = 10
Viewing Angle
[degree]
Vertical
CR = 10
Contrast ratio
Response Time
(Up)
(Down)
Normal Direction
[msec]
Color / Chromaticity
Coordinates (CIE)
Color Coordinates (CIE) White
Central Luminance
(Right)
(Left)
2
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
6
Note
2
3
4
5
P270HVN01.0 Product Specification
Rev.0.0
Note 1: Measurement Method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during
measuring (at surface 35°C). In order to stabilize the luminance, the measurement should be executed after lighting
Backlight for 30 minutes in a stable, windless and dark room.
Photo Detector
Measured Distance
LCD Panel
TFT-LCD Module
Center of the screen
Note 2: Definition of Viewing Angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio
10, at the screen center, over a 180° horizontal and 180° vertical
range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (ș) horizontal left and
right and 90° (ĭ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display
surface with the screen rotated about its center to develop the desired measurement viewing angle.
Note 3: Contrast Ratio measured by TOPCON SR-3
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
7
P270HVN01.0 Product Specification
Rev.0.0
Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full White”
(rising time, TrR), and from “Full White” to “Full Black” (falling time, TrF), respectively. The response time is interval
between the 10% and 90% (1 frame at 60 Hz) of amplitudes.
TrR + TrF = 12 msec (typ.).
%
T rR
T rF
100
90
Optical
White
Black
Black
White
response
10
0
1 Frame
1 Frame
Note 5: Color Chromaticity and Coordinates (CIE) measured by TOPCON SR-3
Note 6: Central Luminance measured by TOPCON SR-3
Note 7: Luminance Uniformity of these 9 points defined as below and measured by TOPCON SR-3
Uniformity =
Minimum Luminance in 9 points (1 - 9)
Maximum Luminance in 9 Points (1 - 9)
Note 8: Crosstalk defined as below and measured by TOPCON SR-3
CT = | YB – YA | / YA × 100 (%)
Where
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
8
P270HVN01.0 Product Specification
Rev.0.0
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note 9: Test Pattern Sub-checker Pattern measured by TOPCON SR-3
R GB R GB
Gray Level = L127
R GB R GB
Gray Level = L0
R GB R GB
Method: Record dBV & DC value with TRD-100
Amplitude
AC
DC
Time
Flicker (dB) = 20 log
AC Level(at 30 Hz)
DC Level
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
9
P270HVN01.0 Product Specification
Rev.0.0
3. Mechanical Characteristics
Item
Unit
Min.
Note
Compression Endurance
[Kgf]
2.5
1
Note 1: Test Method
The point is at a distance from right-downside 25mm x 25mm defined as the Start Point of Measure Points, and the point
is at a distance 25mm from left-side & around 10mm from PCB defined as the End Point.
Align 50mm x 50mm block from Start Point on the Bezel Back, and the corners of each block are Measure Points.
If the distance from the last block to each side of the End Point
25mm, add other blocks to make sure that most area
of Bezel Back can be measured.
PCB
10mm
End Point
25mm
25mm
50mm
25mm
50mm
25mm
The last block
Start Point
25mm
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
10
P270HVN01.0 Product Specification
Rev.0.0
4. Functional Block Diagram
The following diagram shows the functional block of the 27.0 inch Color TFT-LCD Module:
AUO
ASIC
Y-Driver IC
+5V
Timing
Controller
LVDS
Receiver
Connector
LVDS
G1
miniLVDS
Transmitter
TFT-LCD
1920(x3) x 1080
Pixels
X-Driver IC
G1080
D1
D5760
LED
Backlight
DC/DC
Gamma
Converter
Correction
I/F + X-PCB
DC
LED Driver on system
I/F PCB Interface:
MSCKT2407P30HB
AL230F-A0G1D-P
Mating Type:
FI-X30HL(Locked Type)
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
11
P270HVN01.0 Product Specification
Rev.0.0
5. Absolute Maximum Ratings
Absolute maximum ratings of the module are listed as follows:
5.1 TFT LCD Module
Item
Symbol
Min
Max
Unit
Conditions
Logic/LCD Drive Voltage
VDD
-0.3
6.0
[Volt]
Note 1, 2
5.2 Backlight Unit
Item
Symbol
Min
Max
Unit
0
150
[mA]
0
210
[mA]
0
3
[Volt]
Conditions
IRLED1
LED Forward Current
IRLED2
Note 1,2,5
100% duty
IRLED3
IRLED4
IPLED1
LED Pulse Forward Current
IPLED2
IPLED3
Note 1,2,5
10% duty @100Hz
IPLED4
LED forward Voltage variation
ǻVf
(per string variation)
Note 1,2
5.3 Absolute Ratings of Environment
Item
Symbol
Min.
Max.
Unit
Conditions
Operating Temperature
TOP
0
+50
[°C]
Note 3
Glass Surface Temperature
(Operation)
TGS
0
+65
[°C]
Note3
Note4
Operation Humidity
HOP
5
90
[%RH]
Storage Temperature
TST
-20
+60
[°C]
Storage Humidity
HST
5
90
[%RH]
Note 1: With in Ta (25 °C)
Note 2: Permanent damage to the device may occur if exceeding maximum values
Note 3: Temperature and relative humidity range are shown as the below figure.
1. 90% RH Max ( Ta 39°C)
2. Max wet-bulb temperature at 39°C or less. ( Ta 39°C)
3. No condensation
Note 4: Function Judged only
Note 5: IRLED1,2,3,4 and IPLED1,2,3,4 define as per strings LED current.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
12
Note 3
P270HVN01.0 Product Specification
Rev.0.0
Operating Range
Storage Range
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
13
P270HVN01.0 Product Specification
Rev.0.0
6 Electrical Characteristics
6.1 TFT LCD Module
6.1.1
Power Specification
Input power specifications are listed as follows:
Symbol
VDD
IDD1
PDD1
IRush
VDDrp
Description
Logic/LCD Drive
Voltage
Min
Typ.
Max
Unit
Conditions
4.5
5.0
5.5
[Volt]
-
1.02
1.22
[A]
VDD= 5.0V, All white Pattern at 60 Hz
-
1.21
1.45
[A]
VDD= 5.0V, All white Pattern at 75 Hz
-
5.1
6.12
[Watt]
VDD= 5.0V, All white Pattern at 60 Hz
-
6.05
7.26
[Watt]
VDD= 5.0V, All white Pattern at 75 Hz
-
-
3
[A]
-
-
500
+/-10%
Input Current
VDD Power
Inrush Current
Allowable Logic/LCD
Drive Ripple Voltage
[mV] p-p VDD= 5.0V, All white Pattern at 75 Hz
Note 1: Measurement Conditions:
The duration of rising time of power input is 470 us.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
14
Note 1
P270HVN01.0 Product Specification
Rev.0.0
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
15
P270HVN01.0 Product Specification
Rev.0.0
6.1.2
Signal Electrical Characteristics
(1) DC Characteristics of each signal are as following:
Symbol
Description
Min
Typ
Max
Units
VTH
Differential Input High
Threshold
-
-
+100
[mV]
VTL
Differential Input Low
Threshold
-100
-
-
[mV]
ŇVIDŇ
Input Differential Voltage
100
-
600
[mV]
Note 1
VCM
Differential Input Common
Mode Voltage
+1.0
+1.2
+1.5
[V]
VTH-VTL = 200MV (max)
Note 1
Note 1: LVDS Signal Waveform
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
16
Conditions
VCM = 1.2V
Note
1
VCM = 1.2V
Note
1
P270HVN01.0 Product Specification
Rev.0.0
(2) AC Characteristics
Symbol
FDEV
FMOD
Description
Maximum deviation of input clock
frequency during SSC
Maximum modulation frequency of
input clock during SSC
Min
Max
Units
-
±3
%
-
200
KHz
Conditions
Freq
Fmax
Fcenter * FDEV
Fmin
1
FMOD
Time
< Spread Spectrum>
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
17
P270HVN01.0 Product Specification
Rev.0.0
6.2 Backlight Unit
Parameter guideline for LED driving is under stable conditions at 25 °C (Room Temperature):
Symbol
Description
Min.
Typ.
Max.
Unit
Note
-
110
115.5
44.25
49.5
54
[Volt]
Note 2
-
21.78
24.95
[Watt]
Note 3
30,000
-
-
IRLED1
IRLED2
LED Forward Current
[mA]
Note 1
IRLED3
IRLED4
VLB
Light Bar Operation Voltage
(for reference)
PBLU
BLU Power Consumption (for reference)
LTLED
LED Life Time (Typical)
[Hour]
Note 4
Each module consists of 60 pcs LED ( 4 strings x 15 pcs / string )
Note 1: The specified current is 100% duty of LED chip input current, IRLED1,2,3,4 define as per strings LED current.
Note 2: The value showed is one string operation voltage.
Note 3: PBLU = VLED *( IRLED1+IRLED2+IRLED3+IRLED4)
Note 4: Definition of life time: Brightness becomes to 50% of its original value. The minimum life time of LED unit is on
the condition of IRLED = 110mA and 25±2°C (Room Temperature).
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
18
P270HVN01.0 Product Specification
Rev.0.0
7 Signal Characteristics
7.1 Pixel Format Definition
Following figure shows the relationship between the input signals and LCD pixel format.
VW/LQH
5 * % 5 * %
5 *% 5 * %
/LQH
5 * % 5 * %
5 *% 5 * %
7.2 Input Data Format Definition
Note 1:
R/G/B data 7:MSB, R/G/B data 0:LSB
O = “Odd Pixel Data”
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
19
E = “Even Pixel Data”
P270HVN01.0 Product Specification
Rev.0.0
7.3 Signal Description
PIN #
SIGNAL NAME
DESCRIPTION
1
RxOIN0-
Negative LVDS differential data input (Odd data)
2
RxOIN0+
Positive LVDS differential data input (Odd data)
3
RxOIN1-
Negative LVDS differential data input (Odd data)
4
RxOIN1+
Positive LVDS differential data input (Odd data)
5
RxOIN2-
Negative LVDS differential data input (Odd data, DSPTMG)
6
RxOIN2+
Positive LVDS differential data input (Odd data, DSPTMG)
7
GND
Power Ground
8
RxOCLK-
Negative LVDS differential clock input (Odd clock)
9
RxOCLK+
Positive LVDS differential clock input (Odd clock)
10
RxOIN3-
Negative LVDS differential data input (Odd data)
11
RxOIN3+
Positive LVDS differential data input (Odd data)
12
RxEIN0-
Negative LVDS differential data input (Even data)
13
RxEIN0+
LVDS differential data input (Even data)
14
GND
Power Ground
15
RxEIN1-
Negative LVDS differential data input (Even data)
16
RxEIN1+
Positive LVDS differential data input (Even data)
17
GND
Power Ground
18
RxEIN2-
Negative LVDS differential data input (Even data)
19
RxEIN2+
Positive LVDS differential data input (Even data)
20
RxECLK-
Negative LVDS differential clock input (Even clock)
21
RxECLK+
Positive LVDS differential clock input (Even clock)
22
RxEIN3-
Negative LVDS differential data input (Even data)
23
RxEIN3+
Positive LVDS differential data input (Even data)
24
GND
Power Ground
25
NC
No connection (for AUO test only. Do not connect)
26
NC
No connection (for AUO test only. Do not connect)
27
NC
No connection (for AUO test only. Do not connect)
28
VDD
Power +5V
29
VDD
Power +5V
30
VDD
Power +5V
Note 1: Input signals of odd and even clock shall be the same timing.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
20
P270HVN01.0 Product Specification
Rev.0.0
LVDS C/N PIN 1
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
21
L/B C/N PIN 1
P270HVN01.0 Product Specification
Rev.0.0
7.4 Timing Characteristics
The input signal timing specifications are shown as the following table
Signal
Item
Symbol
Min
Period
Tv
Active
Tdisp(v)
Blanking
Tbp(v)+Tfp(v)+PWvs
Period
Th
Active
Tdisp(h)
Blanking
Tbp(h)+Tfp(h)+PWhs
Period
Tclk
Frequency
Freq
Frame rate
Frame rate
VFreq
Hsync
Hsync
Frequency
Frequency
Vertical Section
Horizontal
Section
Clock
HFreq
Typ
Max
1092
1130
1793
1080
1080
1080
12
50
713
1004
1050
1100
960
960
960
44
90
140
11.1
14.0
18.2
54.8
71.2
90.0
50
60
76
55
68
90
Note 1: DE mode only
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
22
Unit
Th
Th
Th
Tclk
Tclk
Tclk
ns
MHz
Hz
KHz
P270HVN01.0 Product Specification
Rev.0.0
7.5 Timing Diagram
7Y
0SL[HO
7EONY
7GLVSY
1/LQH
<
7K
;
'(
1
5*%'DWD
,QYDOLG'DWD
/LQH
1
/LQH
/LQH
/LQH
/LQH
/LQH
,QYDOLG'DWD
&/.
7FON
7K
7EONK
7GLVSK
'(
5*%'DWD 3L[HO 3L[HO 3L[HO 3L[HO
2GG
0 0 0 0
,QYDOLG'DWD
5*%'DWD 3L[HO 3L[HO 3L[HO 3L[HO
(YHQ
0 0 0 0
,QYDOLG'DWD
3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO
3L[HO 3L[HO 3L[HO 3L[HO 3L[HO 3L[HO
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
23
3L[HO 3L[HO 3L[HO
0
0
3L[HO3L[HO
0
0
0
3L[HO
0
,QYDOLG'DWD
,QYDOLG'DWD
3L[HO 3L[HO
3L[HO 3L[HO
P270HVN01.0 Product Specification
Rev.0.0
7.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the chart. Signals from
any system shall be Hi-Z state when VDD is off.
T1
90%
90%
10%
10%
Power Supply VDD
T5
T2
LVDS Signal
T6
T7
VALID
DATA
T3
T4
Backlight On
Power Sequence Timing
Value
Parameter
Unit
Min.
Typ.
Max.
T1
0.5
-
10
[ms]
T2
0
-
50
[ms]
T3
500
-
-
[ms]
T4
100
-
-
[ms]
T5
0
-
50
T6
5
-
100
T7
1000
-
-
Note1 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off.
Note2 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
24
[ms]
Note1,2
[ms]
Note1,2
[ms]
P270HVN01.0 Product Specification
Rev.0.0
8 Connector and Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating the
following signals and will be following components.
8.1 TFT LCD Module
Connector Name / Designation
Interface Connector / Interface Card
STM
Manufacturer
P-TWO
MSCKT2407P30HB
Type Part Number
AL230F-A0G1D-P
Mating Housing Part Number
8.1.1
FI-X30HL (Locked Type)
Pin Assignment
Pin#
Signal Name
Pin#
Signal Name
1
RxOIN0-
2
RxOIN0+
3
RxOIN1-
4
RxOIN1+
5
RxOIN2-
6
RxOIN2+
7
GND
8
RxOCLKIN-
9
RxOCLKIN+
10
RxOIN3-
11
RxOIN3+
12
RxEIN0-
13
RxEIN0+
14
GND
15
RxEIN1-
16
RxEIN1+
17
GND
18
RxEIN2-
19
RxEIN2+
20
RxECLKIN-
21
RxECLKIN+
22
RxEIN3-
23
RxEIN3+
24
GND
25
27
29
NC (for AUO test only. Do not
connect)
NC (for AUO test only. Do not
connect)
VDD
26
connect)
28
VDD
30
VDD
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
25
NC (for AUO test only. Do not
P270HVN01.0 Product Specification
Rev.0.0
8.2 LED Connector on Backlight Unit
This connector is mounted on LED light bar.
Connector Name / Designation
Light Bar Connector
Manufacturer
E&T(ENTERY)
Type Part Number
3707K-S06N-21R
Mating Housing Part Number
H112K-P06N-13B (Locked Type)
8.2.1
LED Pin assignment
Pin#
Signal Name
1
IRLED (current out)
2
IRLED (current out)
3
VLED (voltage in)
4
VLED (voltage in)
5
IRLED (current out)
6
IRLED (current out)
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
26
P270HVN01.0 Product Specification
Rev.0.0
8.2.2
LED Connector Dimension
H × V × D = 13.9 × 3.00 × 4.25, Pitch = 1.0(unit = mm)
8.2.3
LED Mating housing dimension
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
27
P270HVN01.0 Product Specification
Rev.0.0
9 Reliability Test
Environment test conditions are listed as following table.
Items
Required Condition
Temperature Humidity Bias (THB)
Ta= 50°C, 80%RH, 300 hours
High Temperature Operation (HTO)
Ta= 50°C, 50%RH, 300 hours
Low Temperature Operation (LTO)
Ta= 0°C, 300 hours
High Temperature Storage (HTS)
Ta= 60°C, 300 hours
Low Temperature Storage (LTS)
Ta= -20°C, 300 hours
Note
Acceleration: 1.5 Grms
Vibration Test
Wave: Random
(Non-operation)
Frequency: 10 - 200 Hz
Duration: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Shock Test
Wave: Half-sine
(Non-operation)
Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Drop Test
Height: 46 cm, package test
Thermal Shock Test (TST)
-20°C/30min, 60°C/30min, 100 cycles
On/Off Test
On/10sec, Off/10sec, 30,000 cycles
Note 1
Contact Discharge: ± 15KV, 150pF(330ȍ ) 1sec,
15 points, 25 times/ point
Note 2
ESD (Electro Static Discharge)
Air Discharge: ± 15KV, 150pF(330ȍ ) 1sec
15 points, 25 times/ point
Operation: 18,000 ft
Altitude Test
Non-Operation: 40,000 ft
Note 3
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change.
A cycle of rapid temperature change consists of varying the temperature from -20°C to 60°C, and back again. Power is
not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours
before power on.
Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed:
¾
No data lost
¾
Self-recoverable
¾
No hardware failures
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
28
P270HVN01.0 Product Specification
Rev.0.0
10 Shipping label
The label on the panel is shown as below:
Manufactured XX/XX
Model No: P270HVN01.0
AU Optronics
for identification.
Note 1: For Pb Free products, AUO will add
Note 2: For RoHS compatible products, AUO will add
Note 3: For China RoHS compatible products, AUO will add
for identification.
for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal Green
Team.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
29
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
10 Mechanical Characteristics
Front View
30
Rev.0.0
P270HVN01.0 Product Specification
Specificatio
i n
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
Back View
31
Rev.0.0
P270HVN01.0 Product Specification
Specificatio
i n
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
COF Position
Avoid touching COF position
when doing mechanical design
32
Rev.0.0
P270HVN01.0 Product Specification
Specificatio
i n
P270HVN01.0 Product Specification
Rev.0.0
11 Packing Specification
11.1 Packing Flow
9PCS/Carton
Corner angle
Moisture-proof film
Stretch film
Label
PET band
Corner angle
Pallet
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
33
P270HVN01.0 Product Specification
Rev.0.0
11-2 Pallet and shipment information
Specification
Item
Remark
Q'ty
Dimension
Weight(kg)
1
Panel
1
613.6(H)mm x 356.85(V)mm x 10(D)mm
2.18
2
Cushion
1
-
4.41
3
Box
1
720(L)mm x 264(W)mm x 460(H)mm
1.35
without Panel & cushion
4
Packing Box
9 pcs/Box
720(L)mm x 264(W)mm x 460(H)mm
25.39
with panel & cushion
5
Pallet
1
1070(L)mm x 740(W)mm x 138(H)mm
12.9
6
Pallet after
Packing
8 boxes/pallet
1070(L)mm x 740(W)mm x 138(H)mm
216
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
34
P270HVN01.0 Product Specification
Rev.0.0
12 Precautions
1)
Since front polarizer is easily damaged, pay attention not to scratch it.
2)
Be sure to turn off power supply when inserting or disconnecting from input connector.
3)
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4)
When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5)
Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6)
Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.
7)
Do not open or modify the Module Assembly.
8)
Do not press the reflector sheet at the back of the module to any directions.
9)
In case if a Module has to be put back into the packing container slot after once it was taken out from the container,
do not press the center of LED light bar edge. Instead, press at the far ends of the LED light bar edge softly.
Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector
of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even momentary. At
designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the
TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be
supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied
exemption.
13) Avoid touching COF position while doing mechanical design.
14) While storing modules as spares for a long time, the following precautions are necessary:
¾
Store modules in a dark place. Do not expose them to sunlight or fluorescent light.
¾
Keep the temperature between 5°C and 35°C at normal humidity.
© Copyright AUO Optronics Corp. 2012 All Rights Reserved.
35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising