QS_FP3070 Series.cdr
Quick Start Manual for
FP3070 Series
Grounding:
The optimum method for grounding electronic equipment is to ground it
separately from other high-power systems, and to ground more than one
unit of electronic equipment with a single-point ground.
The grounding marked terminal (see below) is provided on the unit.
Note: Do not use a ground that has an unstable impedance, such as
painted screws, or ground subject to vibration.
Product Codes:
FP3070TN:
FP3070T:
800 x 480, WVGA, 7” color TFT with 2 comm port,
one USB USB Device (Type B, Micro), Host and
Ethernet port. MicroSD HC Slot
System Components:
- FP3070Tx unit with LCD, Touch Screen and RTC
- Power Supply Connector
- Installation Kit: Gasket, two Mounting hardware
(each mounting hardware set consists of single cap nut,
screw and clamp).
- *FlexiSoft Software Installer DVD
800 x 480, WVGA, 7” color TFT with 2 comm port,
one USB Device, and Host
*FlexiSoft: Please check the latest version each time.
Note: User should order PLC / programming cable separately.
Panel Mounting and Panel cut-out:
Dimensions:
Port Details (COM1/COM2):
Pin description of communication port for FP3070Tx models are as:
Ethernet Port:
1. Fully compliant with IEEE 802.3 / 802.3u standards.
2. 10/100 Mbps support.
3. Connector used: Standard shielded RJ-45 female jack with inbuilt speed and link activity indication LEDs.
USB Slave Port:
1. USB Device, compliant with USB 2.0 specification, self
powered device.
2. Connector used: Micro USB Type B Female connector.
USB Host:
1. USB Host, compliant with USB 2.0 specification
2. USB Host can be used to transfer logged data and historical
alarm to USB memory stick.
3. USB Host can handle only USB memory stick devices and can
source current up to 150mA only.
Connector used: Standard USB Type A Female connector.
FP3070Tx Series Specifications:
FP3070Tx is Flexi Panel series product.
Flexi Panel Series operator interfaces provide human-machine
interface for PLCs / Inverters. It communicates with PLCs / Inverters
over serial communication port to fetch the information. Information
can be displayed over LCD or can be used to build a logic.
Power:
Display:
Bezel:
LEDs:
Memory:
Communication:
USB Ports:
Ethernet:
SD Card
microSD
HC
COM1
COM2
ETHERNET
HOST
Operating Temp.:
Humidity:
Panel cutout:
Weight:
24VDC (+/- 15%)
800 x 480 WVGA, Multicolor Color backlite,
Graphical Display
IP 66 rated
1
45 MB Max. Application Memory
COM1 and COM2: RS232/RS485
1 USB Device and 1 USB Host
1 Ethernet Port
Micro SD [High Capacity (4GB to 32GB)]
Speed Class:
While inserting and removing SD card, power
should be TURNED-OFF.
*
o
0 to 60 C
10% to 90% (Non condensing)
175.00 mm x 127.00 mm
Approx. 400gm
o
SLAVE
Panel cut-out:
COM1 and COM2:
Tighten the mounting screws evenly to a torque between 0.4 N/m to maintain water and
dust resistance.
Make sure the panel is not dirty and warped and that it is strong enough to hold the unit.
Note: Maximum Panel thickness (On which unit is to be mounted) should be 6mm
(Tolerance: +/-0.2mm).
Quick Start Manual
Doc. No.: QS\3043\1214; Ver.: 1.00
Pin number
1
2
3
4
5
6
7
8
9
Shell
Pin name
TX+
TXD
RXD
RX+
GND
NC
NC
TXRX-
Description
RS-422 transmit +
RS-232 transmit
RS-232 receive
RS-422 receive +
Signal Ground
Not connected
Not connected
RS-422 transmit RS-422 receive Shield
o
Note: *For UL, operating temperature range is 0 C to 50 C.
WARNING:
-> This equipment is suitable for use in Class I, Division 2, Groups A, B,
C and D or non-hazardous locations only.
-> WARNING – EXPLOSION HAZARD – Do not disconnect equipment
unless power has been removed or the area is known to be nonhazardous.
-> WARNING – EXPLOSION HAZARD - Substitution of components may
impair suitability for Class I, Division 2.
-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not
Recharge, Disassemble Or Dispose Of In Fire.
-> WARNING - Replace Battery With type CR1225FH-LF, manufactured
by Renata SA, only. Use of Another Battery May Present A Risk Of Fire
Or Explosion. See Owner's Manual For Safety Instructions”
-> The list of materials used in the construction of these devices with
name of sealed device - generic name of the material and the supplier's
name and type designation.
-> It is recommended that the user periodically inspect the sealed
devices used, for any degradation of properties and Replace the device if
any degradation is found.
Renu Electronics Pvt. Ltd.;
Pub.: 03/2015
Cable Diagrams:
4 Wire RS422/RS485 Cable connections:
Getting Started:
User should follow the given sequence to configure and use any
Flexi Panel series unit:
1.
Install FlexiSoft Software.
2.
Create a PZM application using FlexiSoft software.
3.
Connect programming cable.
4.
Download Firmware i.e. driver for the PLC if PLC is
being used. FP unit cannot communicate with PLC till
the required driver is downloaded to the unit.
5.
Download application.
6.
Now FP unit is ready to use in the system.
DB9 MALE (RS232)
Install the software:
The minimum system requirements for running the FlexiSoft
software are:
Processor
800MHz Pentium processor OR euivalent
processor
Operating
Microsoft Windows 2000
System
Microsoft Windows XP Professional / Home
Edition with SP2 / Vista
RAM
256MB
Hard Disk
800MB (including 200MB for the .NET
Space
Framework Redistributable)
Display
1024 x 768 High Color 16-bit
Mouse/
Required
Keyboard
1
4
5
8
9
Cable Diagrams:
2 Wire RS485 Cable connections:
(i) Insert the DVD in the PC drive and follow the instructions
given.
(ii) In case the software does not autoexecute, please run the
\DISK1\SETUP.EXE file from DVD.
(iii) In case software has been downloaded from the Web site, first
Extract the software installation files, then run the Setup.exe file.
DB9 MALE (RS232)
Cable Diagrams:
PC to unit programming cable:
1
4
5
8
9
DB9 MALE (RS232)
2
3
5
Quick Start Manual
Doc. No.: QS\3043\1214; Ver.: 1.00
Technical Support
For Technical support please contact factory along with the unit
serial number and revision number written on the address sticker
of the unit. Also provide information of the PLC if used in
application.
Head Office:
Survey No. 2/6, Baner Road, Pune – 411 045.
Maharashtra, INDIA
Tel: +91 20 27292840
Fax: +91 20 27292839
E-mail: support@renuelectronics.com
Website: www.renuelectronics.com
Factory:
Gat Number 1163, Village Ghotawade,
Taluka Mulshi, District Pune,
Pune: 412115. Maharashtra,
India
Ph: +91 20 66872900
MANUAL REVISIONS:
Rev. No. Doc. No.
1.00
QS\3043\1214
Date
24/12/14
Description
First Draft
Renu Electronics Pvt. Ltd.;
Pub.: 03/2015
CNTL/DWG/FP3070/1214
CONTROL DRAWING - FP SERIES
FP3043Tx Series
JP8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising