User Access Level of Web/Phone/Handset User Interface

User Access Level of Web/Phone/Handset User Interface
User Access Level of Web/Phone/Handset User
Interface
Overview
User access level feature is used to achieve different access levels for different authorized users.
It is useful for protecting the IP phone from unauthorized configuration, and popularly used for
the Hosted PBX solution. The following describes how to customize the access permission for
configurations on the web user interface and phone user interface.
This guide applies to the following Yealink IP phones:

SIP VP-T49G, CP860 and W56P IP phones running firmware version 80 or later

SIP-T48G, SIP-T48S, SIP-T46G, SIP-T46S, SIP-T42G, SIP-T42S, SIP-T41P, SIP-T41S, SIP-T40P,
SIP-T29G, SIP-T27P, SIP-T27G, SIP-T23P/G, SIP-T21(P) E2 and SIP-T19(P) E2 IP phones
running firmware version 81 or later
Scenario
For a Hosted PBX solution, IP phones are provided to customers for free but required a
minimum consumption monthly. All PBX services associated features on the deployed IP phones
are preconfigured to avoid customers from using other Hosted PBX’s service, and the Hosted
PBX system administrator can restrict the user access permission using user access level feature.
For example, the Hosted PBX system administrator restricts the write permission of the account
associated configurations. This means customers can only read these configurations on both
web user interface and phone user interface.
Introduction
Yealink SIP VP-T49G, SIP-T48G/S, SIP-T46G/S, SIP-T42G/S, SIP-T41P/S, SIP-T40P, SIP-T29G,
SIP-T27P/G, SIP-T23P/G, SIP-T21(P) E2, SIP-T19(P) E2, CP860 and W56P IP phones support
access levels of admin, var and user. The following describes the detailed information of each
access level:

Admin: The administrator access level. With this access level, all configurations on both
web user interface and phone user interface can be read and written. The authentication
identity for this access level is admin. And the default password is admin.

Var: The value-added reseller access level. Generally, with this access level, most
configurations on the web user interface and phone user interface can be read and written.
The authentication identity for this access level is var. And the default password is var.
1
Configuration Guide for User Access Level

User: The end user access level. Generally, only a few configurations are allowed to be
written and read for access user. The authentication identity for this access level is user.
And the default password is user.
Specification
Access permissions of all configuration items available on Yealink W56P/SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23P/T23G
/T21(P) E2/T19(P) E2/CP860 IP phones’ web user interface and phone/handset user interface can
be defined in a fixed WebItemsLevel.cfg file. Each configuration item in the file is formatted as:
ItemName = X1X2
The valid values of X1, X2 include 0, 1, 2 and 3.
X1 is used for specifying the access level. The access levels: 2 = admin, 1 = var, 0 = user, 3 =
none.
X2 is used for defining the access permission. 2 means the configuration item is read-only for X1
and higher access levels, the highest is always writable. 1 means the configuration item is
read-only for X1 access level, and writable for higher access levels. 0 means the configuration
item is writable for X1 and higher access levels. 3 means the configuration item is read-only for
X1 and higher access levels.
The following table lists the possible values of X1X2 and the configuration results with different
access levels:
(W: writable; R: read-only; N: hidden)
Results
admin (2)
var (1)
user (0)
0
WR
WR
WR
1
WR
WR
N
2
WR
N
N
3
N
N
N
00
WR
WR
WR
01
WR
WR
R
02
WR
R
R
03
R
R
R
10
WR
WR
N
11
WR
R
N
12
WR
R
N
13
R
R
N
Values of X1X2
2
Configuration Guide for User Access Level
Results
admin (2)
var (1)
user (0)
20
WR
N
N
21
WR
N
N
22
WR
N
N
23
R
N
N
30/31/32/33
N
N
N
Values of X1X2
3
Configuration Guide for User Access Level
Application
This section will introduce procedures to configure access permission of the web user interface
in detail. The flow chart of configuring user access level is shown as below:
Note: The boot file is only applicable to IP phones running firmware version 81 or later. The
parameter varies from firmware version to firmware version (refer to Configuring Yealink IP
Phones).
Edit the desired configuration items in the Yealink-supplied template file
“WebItemsLevel.cfg”.
Upload the WebItemsLevel.cfg file to the directory of the provisioning server.
Edit the configuration file (e.g., y000000000028.cfg, features.cfg):
1.
Set the value of parameter “static.security.var_enable” to 1.
2.
Configure the value of the parameter “static.web_item_level.url”.
(e.g., ftp://<ServerIPAddress>/WebItemsLevel.cfg)
Upload the configuration file (e.g., y000000000028.cfg, features.cfg) to the
directory of the provisioning server.
Edit the boot file (e.g., y000000000000.boot):
1.
Reference the configuration file in the boot file (e.g., include: config
“ftp://<ServerIPAddress>/features.cfg”).
1.
2.
Upload the boot file (e.g., y000000000000.boot) to the directory of the
provisioning server.
Trigger the IP phone to perform auto provisioning.
Settings take effect after phone reboot. You can login the web user interface
with different access levels to check the settings.
4
Configuration Guide for User Access Level
Customizing WebItemsLevel.cfg
You can ask Yealink Field Application Engineer for the template file “WebItemsLevel.cfg”, or you
can download it online:
http://support.yealink.com/documentFront/forwardToDocumentFrontDisplayPage.
We recommend you only edit the desired configuration items in the supplied
“WebItemsLevel.cfg" file, and keep other configuration items constant.
WebItemsLevel.cfg downloaded via auto provisioning will override that in the phone flash.
Access level of any configuration item missed (including configuration value left blank) in the
downloaded WebItemsLevel.cfg file will be changed to user by default.
The following shows configuration segments for the web user interface in the
WebItemsLevel.cfg file for reference:
Sample 1: Configuration items in the WebItemsLevel.cfg for navigation bar settings of the
Features page:
[ Features ]
features-forward = 0
features-general = 0
features-audio = 0
features-intercom = 0
features-transfer = 1
features-callpickup = 0
features-remote = 2
features-phonelock = 0
features-acd = 0
features-sms = 2
features-actionurl = 1
features-bluetooth = 0
features-powerled = 2
features-notifypop = 0
5
Configuration Guide for User Access Level
According to the above configuration of access level, when logging in the web user interface
with user access level, the web user interface displays as below:
6
Configuration Guide for User Access Level
When logging in the web user interface with var access level, the web user interface displays as
below:
7
Configuration Guide for User Access Level
When logging in the web user interface with admin access level, the web user interface displays
as below:
Note: Configuration items for navigation bar are not writable on both web user interface and
phone user interface. So, configuration items for navigation bar can be configured only using
the format “ItemName = X”.
If the access permission of the first navigation configuration item for each main page is
restricted, the access to the main web page will be denied.
The following table lists the first navigation configuration items for each main page:
Main Page
First Navigation Item
Configuration Item
Account
Register
account-register
Network
Basic
network-basic
Line Key 1-11 (for SIP
VP-T49G/SIP-T48G/T48S),
DSSKey/Dsskey
(not applicable
to W56P)
Line Key 1-9 (for
SIP-T46G/T46S/T29G),
Line Key 1-7 (for SIP-T27P/G),
linekey
Line Key 1-5 (for
SIP-T42G/T42S/T41P/T41S),
Line Key (for SIP-T40P/T23P/T23G),
8
Configuration Guide for User Access Level
Main Page
First Navigation Item
Configuration Item
Line Key (for SIP-T21(P) E2),
Programable key (for SIP-T19(P)
E2/CP860)
Features
Forward&DND
features-forward
Settings
Preference
settings-preference
Directory
Local Directory
contacts-basic
Security
Password
password
For example, set the value of the configuration item “settings-preference” to be 1.
When logging into with user access level, the access to the Settings web page will be denied.
Sample2: Configuration items in the WebItemsLevel.cfg for the Register settings of Account
page:
[ Account-Register ]
switch-account = 0
account_status = 0
line_active = 0
account_label = 11
display_name = 01
register_name = 03
user_name = 01
account_password = 12
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
backup-outbound-proxy-server = 01
NAT_traversal = 12
9
Configuration Guide for User Access Level
sip_server = 2
sip_server2 = 2
outbound-proxy-server-port = 2
backup-outbound-proxy-server-port = 2
According to the above configuration of access level, when logging in the web user interface
with user access level, the web user interface displays as below:
When logging in the web user interface with var access level, the web user interface displays as
below:
10
Configuration Guide for User Access Level
When logging in the web user interface with admin access level, the web user interface displays
as below:
For more information on parameters of the WebItemsLevel.cfg file, refer to Appendix-A:
Configuration Parameters on page 23.
For SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23
P/T23G/T21(P) E2/T19(P) E2/CP860 IP phones:
The following shows configuration segments for the phone user interface in the
WebItemsLevel.cfg file for reference:
If you set the access permission of the high level, it will have an impact on that of the low level.
In the following examples, the call forward menu has a higher level than always forward/busy
forward/no answer forward submenu.
11
Configuration Guide for User Access Level
Example1: Configuration items in the WebItemsLevel.cfg for call forward menu and its submenu
settings:
[ GUI ]
callcontrol_forward = 02
always-forward = 10
busy-forward = 00
NoAnswer-forward = 00
Note: The configuration of busy forward is the same as the one of the no answer forward, so the
following figures take busy forward as an example.
According to the above configuration of access level, when logging in to the phone user
interface with user access level, the access permission of each submenu is displayed as below:
Always forward submenu is hidden for user access level:
Busy forward/no answer forward submenu is read-only for user access level:
When logging in to the phone user interface with var access level, the access permission of each
submenu is displayed as below:
12
Configuration Guide for User Access Level
Always forward submenu is read-only for var access level:
Busy forward/no answer forward submenu is read-only for var access level:
When logging in to the phone user interface with admin access level, the phone user interface
displays as below:
Always forward submenu is writable for admin access level:
13
Configuration Guide for User Access Level
Busy forward/no answer forward submenu is writable for admin access level:
Example2: Configuration items in the WebItemsLevel.cfg for call forward menu and its submenu
settings:
[ GUI ]
callcontrol_forward = 00
always-forward = 01
busy-forward = 02
NoAnswer-forward = 00
According to the above configuration of access level, when logging in to the phone user
interface with user access level, the access permission of each submenu is displayed as below:
Always forward submenu is read-only for user access level:
Busy forward submenu is read-only for user access level:
14
Configuration Guide for User Access Level
No answer forward submenu is writable for user access level:
When logging in to the phone user interface with var access level, the access permission of each
submenu is displayed as below:
Always forward submenu is writable for var access level:
Busy forward submenu is read-only for var access level:
15
Configuration Guide for User Access Level
No answer forward submenu is writable for var access level:
When logging in to the phone user interface with admin access level, the phone user interface
displays as below:
Always forward submenu is writable for admin access level:
Busy forward submenu is writable for admin access level:
16
Configuration Guide for User Access Level
No answer forward submenu is writable for admin access level:
For W56P IP DECT phones:
The following shows configuration segments for the handset user interface in the
WebItemsLevel.cfg file for reference:
If you set the access permission of the high level, it will have an impact on that of the low level.
In the following examples, the Settings menu has a higher level than other submenus.
Example: Configuration items in the WebItemsLevel.cfg for Telephony submenu settings:
[ GUI ]
Auto_Answer = 01
Auto_Intercom = 02
Default_Line = 03
Incoming_Lines = 02
Speed_Dial = 0
Blacklist = 1
According to the above configuration of access level:
For user access level, the Blacklist submenu is hidden. The Auto Answer, Auto Intercom, Default
Line and Incoming Lines submenus are read-only. Only the Speed Dial submenu is writable.
For var access level, the Auto Intercom, Default Line and Incoming Lines submenus are
read-only. The Auto Answer, Speed Dial and Blacklist submenus are writable.
For admin access level, only the Default Line submenu is read-only, the others are writable.
For more information on parameters of the WebItemsLevel.cfg file, refer to Appendix-A:
Configuration Parameters on page 23.
17
Configuration Guide for User Access Level
Configuring Yealink IP Phones
User access level feature is disabled for Yealink W56P/SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23P/T23G
/T21(P) E2/T19(P) E2/CP860 IP phones in neutral firmware version by default. Before using this
feature, you need to enable it through auto provisioning introduced as following. User access
level feature is configurable only via configuration files.
To configure user access level feature for Yealink IP phones:
1.
Edit the following parameters in the configuration file (e.g., y000000000051.cfg).
Parameters
security.var_enable
Permitted Values
Default
0 or 1
0
Description:
This parameter is used to enable or disable the login of the web/phone/handset user
interface with different access levels.
0-Disabled
1-Enabled
Note: It takes effect after reboot.
Web User Interface:
None
Phone User Interface:
None
security.default_access_level
0, 1 or 2
0
Description:
This parameter is used to configure the default access level to access the
phone/handset user interface.
0-user
1-var
2-admin
Note: It works only if the value of the parameter “security.var_enable” is set to 1
(Enabled). It takes effect after reboot.
Web User Interface:
18
Configuration Guide for User Access Level
Parameters
Permitted Values
Default
None
Phone User Interface:
None
web_item_level.url
FTP, TFTP, HTTP or
HTTPS download URL
Blank
Description:
This parameter is used to configure the access URL of the WebItemsLevel.cfg file.
Note: It takes effect after reboot.
Web User Interface:
None
Phone User Interface:
None
The parameter settings in the configuration file for reference are shown as below:
security.var_enable = 1
web_item_level.url = ftp://192.168.1.100/WebItemsLevel.cfg
security.default_access_level = 1
2.
Upload the configuration file to the directory of the provisioning server.
3.
Configure the access URL of the provisioning server for the IP phone.
4.
Trigger the IP phone to perform auto provisioning.
For more information on auto provisioning Yealink IP phones, refer to Yealink_SIP-T2
Series_T19(P) E2_T4_Series_CP860_W56P_IP_Phones_Auto_Provisioning_Guide.
19
Configuration Guide for User Access Level
To configure user access level feature for Yealink IP phones:
1.
Edit the following parameters in the configuration file (e.g., features.cfg).
Parameters
static.security.var_enable
Permitted Values
Default
0 or 1
0
Description:
This parameter is used to enable or disable the login of the web/phone user interface
with different access levels.
0-Disabled
1-Enabled
Note: It takes effect after reboot.
Web User Interface:
None
Phone User Interface:
None
static.security.default_access_level
0, 1 or 2
0
Description:
This parameter is used to configure the default access level to access the phone user
interface.
0-user
1-var
2-admin
Note: It works only if the value of the parameter “static.security.var_enable” is set to 1
(Enabled). It takes effect after reboot.
Web User Interface:
None
Phone User Interface:
None
static.web_item_level.url
FTP, TFTP, HTTP or
Blank
20
Configuration Guide for User Access Level
Parameters
Permitted Values
Default
HTTPS download URL
Description:
This parameter is used to configure the access URL of the WebItemsLevel.cfg file.
Note: It takes effect after reboot.
Web User Interface:
None
Phone User Interface:
None
The parameter settings in the configuration file for reference are shown as below:
static.security.var_enable = 1
static.web_item_level.url = ftp://192.168.1.100/WebItemsLevel.cfg
static.security.default_access_level = 1
2.
Upload the configuration file to the directory of the provisioning server.
3.
Reference the configuration file in the boot file (e.g., y000000000000.boot).
include:config “ftp://192.168.1.100/features.cfg”
4.
Upload the boot file to the directory of the provisioning server.
5.
Configure the access URL of the provisioning server for the IP phone.
6.
Trigger the IP phone to perform auto provisioning.
The boot file is only applicable to IP phones running firmware version 81 or later. For more
information on auto provisioning Yealink IP phones, refer to Yealink_SIP-T2 Series_T19(P)
E2_T4_Series_IP_Phones_Auto_Provisioning_Guide_V81.
When the user access level is enabled, you can login the web/phone/handset user interface with
different access levels.
To login the web user interface with different access levels:
1.
Press the OK/√ key when the phone is idle to obtain the IP address.
For W56P, press the OK->Status->Base to obtain the IP address.
2.
Enter the IP address (e.g., http://192.168.0.10 or 192.168.0.10) in the address bar of web
browser on your PC and then press the Enter key.
3.
Enter the user name (admin/var/user) and password (admin/var/user) in the login page.
4.
Click Confirm to login.
21
Configuration Guide for User Access Level
When logging in with different access levels, you can see different permissions of web user
interface.
To login the phone user interface with different access levels:
1.
Press Menu->UserMode.
2.
Press
or
, or the Switch soft key to select the desired access level in the User
Type field.
3.
Enter the password in the Password field.
4.
Press the Save soft key to accept the change.
You can see different permissions of phone user interface when logging in with different access
levels.
To login the handset user interface with different access levels:
1.
Press OK->User Mode.
2.
Press
3.
Enter the password in the Password field.
4.
Press the Save soft key to accept the change.
or
to select the desired access level in the User Type field.
You can see different permissions of handset user interface when logging in with different
access levels.
22
Appendix-A Configuration Parameters
Configuration Parameters of Web User Interface
The following table lists configuration items in the WebItemsLevel.cfg file with associated
configurations on the web user interface (take SIP-T46G IP phones as an example for reference):
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Status-Basic = 0
Status->Status (the whole page)
Status-RTP = 0
(not applicable to
W56P IP DECT
Status->RTP Status (the whole page)
phones)
[ Status-Menu ]
Status-VoIP = 0
(only applicable to
W56P IP DECT
Status->Handset&VoIP
phones)
Status-TalkStats = 0
(only applicable to SIP
Status->Talk Statistics (the whole page)
VP-T49G IP phones)
Status->Version
version = 0
DeviceCertificate = 0
(not applicable to SIP
Status->Device Certificate
VP-T49G/CP860/
[ Status ]
W56P IP phones)
Status->Network
network = 0
IPv4 = 0
Status->IPv4
23
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Status->IPv6
IPv6 = 0
(not applicable to
W56P IP DECT
phones)
Status->Network Common
NetworkCommon = 0
[ Status ]
Status->Account Status
AccountStatus = 0
(not applicable to
W56P IP DECT
phones)
Status->Ext
For SIP-T29G and SIP-T27P/G:
Ext = 0
(only applicable to
SIP-T48G/T48S/T46G/
T46S/T29G/T27P/
For SIP-T48G/S and SIP-T46G/S:
T27G IP phones)
[ Status-VoIP ]
registered-handset =
Status->Registered Handsets
24
Configuration Guide for User Access Level
Section Header
(only applicable to
W56P IP DECT
phones)
Parameters and
Configuration Items on the Web User
Default Value
Interface
0
registered-new-hands
et = 0
Status->Register New Handsets
voip-status = 0
Status->Paging Status
Paging = 0
Status->VoIP Status
Status->RTP Status
[ RTP-Status ]
(only applicable to
SIP VP-T49G IP
rtcp-status = 11
phones)
Status->Talk Statistics
[ Talk-Stats ]
(only applicable to
SIP VP-T49G IP
talk-stats = 0
phones)
account-register = 0
Account->Register (the whole page)
account-basic = 0
Account->Basic (the whole page)
account-codec = 0
Account->Codec (the whole page)
account-adv = 2
(0 for SIP
VP-T49G/CP860/
Account->Advanced (the whole page)
W56P IP phones)
[ Account ]
account-assign = 0
(only applicable to
Account->Number Assignment (the whole
W56P IP DECT
page)
phones)
account-handsetnam
e=0
(only applicable to
Account->Handset Name (the whole page)
W56P IP DECT
phones)
25
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
account-direct = 0
(only applicable to SIP
Account->SIP IP Call (the whole page)
VP-T49G IP phones)
switch-account = 0
(not applicable to
SIP-T19(P) E2/CP860
Account->Register->Account
IP phones)
account_status = 0
Account->Register->Register Status
line_active = 0
Account->Register->Line Active
account_label = 0
Account->Register->Label
display_name = 0
Account->Register->Display Name
register_name = 01
Account->Register->Register Name
user_name = 01
Account->Register->User Name
account_password =
01
(2 for SIP
Account->Register->Password
VP-T49G/CP860/
W56P IP phones)
[ Account-Register
]
enabled-outbound-pr
oxy-server = 2
(01 for SIP
VP-T49G/CP860/
Account->Register->Enable Outbound
Proxy Server
W56P IP phones)
SIP VP-T49G/CP860/W56P:
Account->Register->Outbound Proxy
Server 1
outbound-proxy-serv
er = 2
Account->Register->Outbound Proxy
Server 1->Port
(01 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2:
Account->Register->Outbound Proxy
Server 1
26
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
outbound-proxy-serv
er-port = 2
(not applicable to SIP
VP-T49G/CP860/
Account->Register->Outbound Proxy
Server 1->Port
W56P IP phones)
SIP VP-T49G/CP860/W56P:
Account->Register->Outbound Proxy
Server 2
backup-outbound-pr
oxy-server = 2
Account->Register->Outbound Proxy
Server 2->Port
(01 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2:
Account->Register->Outbound Proxy
Server 2
backup-outbound-pr
oxy-server-port = 2
(not applicable to SIP
VP-T49G/CP860/
[ Account-Register
]
Account->Register->Outbound Proxy
Server 2->Port
W56P IP phones)
proxy-fallback-interva
l=2
(01 for SIP
Account->Register->Proxy Fallback Interval
VP-T49G/CP860/
W56P IP phones)
transport-item = 2
(only applicable to SIP
VP-T49G/CP860/
Account->Register->Transport
W56P IP phones)
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
NAT_traversal = 2
T21(P) E2/T19(P) E2/CP860/W56P:
Account->Register->NAT
SIP VP-T49G:
27
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Account->Register->NAT
Account->SIP IP Call->NAT
SIP VP-T49G/CP860/W56P:
Account->Register->SIP Server 1/2
sip_server = 2
[ Account-Register
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
]
T21(P) E2/T19(P) E2:
Account->Register->SIP Server 1
sip_server2 = 2
Account->Register->SIP Server 2
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
switch-account = 0
(not applicable to
SIP-T19(P) E2/CP860
Account->Basic->Account
IP phones)
proxy_require = 2
[ Account-Basic ]
(0 for SIP
VP-T49G/CP860/
Account->Basic->Proxy Require
W56P IP phones)
send_anonymous = 1
Account->Basic->Local Anonymous
anonymous_rejection_
Account->Basic->Local Anonymous
enabled = 0
Rejection
anonymous_call_enab
led = 0
Account->Basic->Send Anonymous Code
(for neutral firmware
28
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
version only)
anonymous_call_OnC
ode = 1
Account->Basic->Send Anonymous
(for neutral firmware
Code->On Code
version only)
anonymous_call_OffC
ode = 1
Account->Basic->Send Anonymous
(for neutral firmware
Code->Off Code
version only)
send_anonymous_reje
ction_code = 0
Account->Basic->Send Anonymous
(for neutral firmware
Rejection Code
version only)
anonymous_rejection_
[ Account-Basic ]
OnCode = 1
Account->Basic->Send Anonymous
(for neutral firmware
Rejection Code->On Code
version only)
anonymous_rejection_
OffCode = 1
Account->Basic->Send Anonymous
(for neutral firmware
Rejection Code->Off Code
version only)
misscall-log = 0
(not applicable to
W56P IP DECT
Account->Basic->Missed Call Log
phones)
auto-answer = 0
(not applicable to
W56P IP DECT
Account->Basic->Auto Answer
phones)
auto-answer-mute =
0
(only applicable to
Account->Basic->Auto Answer Mute
CP860 IP phones)
ring-type = 0
(not applicable to
Account->Basic->Ring Type
W56P IP DECT
29
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
phones)
switch-account = 0
(not applicable to
SIP-T19(P) E2/CP860
Account->Codec->Account
IP phones)
Account->Codec->Audio Codecs
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860:
SIP VP-T49G:
[ Account-Codec
]
codecs-group = 0
W56P:
switch-account = 0
[ Account-Adv ]
(not applicable to
Account->Advanced->Account
SIP-T19(P) E2/CP860
30
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
IP phones)
UDP_keep-alive = 2
(only applicable to SIP
VP-T49G/CP860/
W56P IP phones)
Account->Advanced->Keep Alive Type
Account->Advanced->Keep Alive
Interval(Seconds)
udp-keep-alive-type
=2
(not applicable to SIP
Account->Advanced->Keep Alive Type
VP-T49G/CP860/
W56P IP phones)
udp-keep-alive-interv
al = 2
(not applicable to SIP
VP-T49G/CP860/
Account->Advanced->Keep Alive
Interval(Seconds)
W56P IP phones)
rport = 2
subscribe-period = 2
Account->Advanced->RPort
Account->Advanced->Subscribe
Period(Seconds)
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
[ Account-Adv ]
Account->Advanced->DTMF Type
Account->Advanced->DTMF Info Type
Account->Advanced->DTMF Payload
Type(96~127)
DTMF_items = 2
SIP VP-T49G:
Account->Advanced->DTMF Type
Account->Advanced->DTMF Info Type
Account->Advanced->DTMF Payload
Type(96~127)
Account->SIP IP Call->DTMF Type
Account->SIP IP Call->DTMF Info Type
Account->SIP IP Call->DTMF Payload
Type(96~127)
reliable_retransmissio
Account->Advanced->Retransmission
31
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
n=2
subscribe-register = 2
Account->Advanced->Subscribe Register
Account->Advanced->Subscribe for MWI
Account->Advanced->MWI Subscription
MWI-items = 2
Period(Seconds)
Account->Advanced->Subscribe MWI To
Voice Mail
voice_mail = 2
(0 for SIP
VP-T49G/CP860/
Account->Advanced->Voice Mail
W56P IP phones)
[ Account-Adv ]
voice_mail_display = 2
(not applicable to
W56P IP DECT
Account->Advanced->Voice Mail Display
phones)
caller-ID-header = 2
Account->Advanced->Caller ID Source
use-session-timer = 2
Account->Advanced-> Session Timer
session-timer = 2
Account->Advanced->Session
Expires(30~7200s)
session-refresher = 2
Account->Advanced->Session Refresher
user-equal-phone = 2
Account->Advanced->Send user=phone
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
Account->Advanced->RTP
voice-encryption = 2
Encryption(SRTP)
SIP VP-T49G:
Account->Advanced->RTP
Encryption(SRTP)
Account->SIP IP Call->RTP
Encryption(SRTP)
ptime-item = 2
BLF-list-URI = 2
(not applicable to
Account->Advanced->PTime(ms)
Account->Advanced->BLF List URI
32
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
SIP-T19(P) E2/
CP860/W56P IP
phones)
BlfListCode = 2
(not applicable to
SIP-T19(P) E2/
Account->Advanced->BLF List Pickup Code
CP860/W56P IP
phones)
BLFListBargeInCode =
2
(not applicable to
Account->Advanced->BLF List Barge In
SIP-T19(P) E2/
Code
CP860/W56P IP
phones)
BLF-List-Retrieve-Cod
e=2
[ Account-Adv ]
(not applicable to
Account->Advanced->BLF List Retrieve Call
SIP-T19(P) E2/
Parked Code
CP860/W56P IP
phones)
share-line = 2
Call-Pull-Feature-Acce
ss-Code = 2
(not applicable to
SIP-T19(P) E2/W56P
IP DECT phones)
Account->Advanced->Shared Line
Account->Advanced->Call Pull Feature
Access Code
(only appear when the parameter
“account.X.shared_line” is set to 1)
dialog-info-call-picku
p=2
(not applicable to
Account->Advanced->Dialog Info Call
SIP-T19(P) E2/
Pickup
CP860/W56P IP
phones)
BLA-number = 2
(not applicable to
W56P/SIP VP-T49G IP
Account->Advanced->BLA Number
phones)
33
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
BLA-subscription-peri
od = 2
(not applicable to
W56P/SIP VP-T49G IP
Account->Advanced->BLA Subscription
Period
phones)
SIP-send-MAC = 2
Account->Advanced->SIP Send MAC
SIP-send-line = 2
Account->Advanced->SIP Send Line
SIP-Reg-retry-timer =
Account->Advanced->SIP Registration
2
Retry Timer(0~1800s)
conference-type = 2
Account->Advanced->Conference Type
conference-uri = 2
Account->Advanced->Conference URI
ACD-subscrip-period
=2
(not applicable to
W56P IP DECT
Account->Advanced->ACD Subscribe
Period(120~3600s)
phones)
[ Account-Adv ]
Earlymedia = 2
(not applicable to
W56P IP DECT
Account->Advanced->Early Media
phones)
SIPServerType = 2
Account->Advanced->SIP Server Type
Music-ServerURI = 2
(not applicable to
W56P IP DECT
Account->Advanced->Music Server URI
phones)
Direct-Call-Pickup-Co
de = 2
(not applicable to
W56P IP DECT
Account->Advanced->Directed Call Pickup
Code
phones)
Group-Call-Pickup-Co
de = 2
(not applicable to
W56P IP DECT
Account->Advanced->Group Call Pickup
Code
phones)
34
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Distinctive-Ring-Tone
s=2
(not applicable to
W56P IP DECT
Account->Advanced->Distinctive Ring
Tones
phones)
UnregisterOnReboot
Account->Advanced->Unregister When
=2
Reboot
Out-Dialog-BLF = 2
(not applicable to
SIP-T19(P) E2/
Account->Advanced->Out Dialog BLF
CP860/W56P IP
phones)
RTCP-Collector-Name
=2
(not applicable to
[ Account-Adv ]
W56P IP DECT
Account->Advanced->VQ RTCP-XR
Collector Name
phones)
RTCP-Collector-Addre
ss = 2
(not applicable to
W56P IP DECT
Account->Advanced->VQ RTCP-XR
Collector Address
phones)
RTCP-Collector-Port =
2
(not applicable to
W56P IP DECT
Account->Advanced->VQ RTCP-XR
Collector Port
phones)
Number-Of-Linekey =
2
(1 for SIP VP-T49G IP
Account->Advanced->Number of line key
phone; not applicable
(only appear when the parameter
to SIP-T19(P) E2/
“features.auto_linekeys.enable” is set to 1)
CP860/W56P IP
phones)
[ Account-Assign ]
(only applicable to
incoming-lines = 0
Account->Number Assignment->Incoming
lines
35
Configuration Guide for User Access Level
Section Header
W56P IP DECT
phones)
Parameters and
Configuration Items on the Web User
Default Value
Interface
outgoing-lines =0
Account->Number Assignment->Outgoing
lines
[ Account-Handse
tname ]
(only applicable to
Handsetname = 1
Account->Handset Name
network-basic = 0
Network->Basic (the whole page)
W56P IP DECT
phones)
network-pcport = 0
(not applicable to
CP860/W56P IP
Network->PC Port (the whole page)
phones)
network-nat = 2
(not applicable to SIP
VP-T49G/CP860/
Network->NAT (the whole page)
W56P IP phones)
[ Network ]
network-advanced =
2
(0 for SIP
Network->Advanced (the whole page)
VP-T49G/CP860/
W56P IP phones)
network-wifi = 0
(only applicable to SIP
VP-T49G/SIP-T48G/
Network->Wi-Fi (the whole page)
T48S/T46G/T46S/
[ Network ]
T29G IP phones)
shotlevel = 0
(only applicable to SIP
VP-T49G/CP860/
W56P IP phones)
ipaddress-mode = 0
[ Network-Basic ]
(2 for SIP
Network->Basic->Internet
VP-T49G/CP860/
Port->Mode(IPv4/IPv6)
W56P IP phones)
36
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Network->Basic->IPv4 Config
ipv4config = 0
(2 for SIP
VP-T49G/CP860/
W56P IP phones)
[ Network-Basic ]
Network->Basic->IPv6 Config
ipv6config = 0
(2 for SIP
VP-T49G/CP860 IP
phones; not
applicable to W56P IP
DECT phones)
wan-ppoe = 2
(only applicable to VP
SIP-T49G/W56P IP
phones)
pcport-active = 0
[ Network-PCPort
(not applicable to
]
CP860/W56P IP
Network->Basic->PPPoE
Network->Basic->PPPoE->User Name
Network->Basic->PPPoE->Password
Network->PC Port->PC Port Active
phones)
Network->NAT->Nat Manual
manual = 2
[ Network-Nat ]
(not applicable to
manual-switch = 2
Network->NAT->Nat Manual->Active
manual-ip = 2
Network->NAT->Nat Manual->IP Address
Network->NAT->ICE
SIP
VP-T49G/CP860/
ICE = 2
W56P IP phones)
ICE-switch = 2
Network->NAT->ICE->Active
STUN = 2
Network->NAT->STUN
37
Configuration Guide for User Access Level
Section Header
[ Network-Nat ]
Parameters and
Configuration Items on the Web User
Default Value
Interface
STUN-switch = 2
Network->NAT->STUN->Active
STUN-server = 2
Network->NAT->STUN->STUN Server
STUN-port = 2
(not applicable to
W56P IP phones)
(1024~65000)
Network->NAT->TURN
SIP
VP-T49G/CP860/
Network->NAT->STUN->STUN Port
TURN = 2
TURN-switch = 2
Network->NAT->TURN->Active
TURN-server = 2
Network->NAT->TURN->TURN Server
TURN-port = 2
Network->NAT->TURN->TURN Port
(1~65535)
TURN-username = 2
Network->NAT->TURN->User Name
TURN-password = 2
Network->NAT->TURN->Password
Network->Advanced->LLDP
LLDP-items = 2
CDP-items = 2
Network->Advanced->CDP
(not applicable to
W56P IP DECT
phones)
Network->Advanced->VLAN
[ Network-Advanc
ed ]
VLAN-items = 2
NAT-items = 2
(only applicable to SIP
Network->Advanced->NAT
38
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
VP-T49G/CP860/
W56P IP phones)
port-link = 2
Network->Advanced->Port Link
(not applicable to
W56P IP DECT
phones)
Network->Advanced->Voice QoS
W56P/CP860/SIP-T48G/T48S/T46G/T46S/
T42G/T42S/T41P/T41S/T40P/T29G/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P) E2:
voice-QoS = 2
SIP VP-T49G:
[ Network-Advanc
ed ]
reserve-port = 0
Network->Advanced->Reserved Port
(only applicable to SIP
VP-T49G IP phones)
local-RTP-port = 2
Network->Advanced->Local RTP Port
(not applicable to SIP
VP-T49G IP phones)
Network->Advanced->Web Server
web-server = 2
Network->Advanced->802.1x
SIP VP-T49G/W56P/CP860:
8021x = 2
39
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
SIP-T48G/T48S/T46G/T46S/T42G/T42S/
T41P/T41S/T40P/T29G/T27P/T27G/T23P/
T23G/T21(P) E2/T19(P) E2:
span-to-pc-port = 2
(not applicable to
Network->Advanced->Span to PC
CP860/W56P IP
phones)
[ Network-Advanc
ed ]
Network->Advanced->Registration
reg-surge-prev = 2
Random
ICMPv6_Status =2
(only applicable to SIP
Network->Advanced->ICMPv6 Status
VP-T49G/SIP-T48G/
T48S/T46G/T46S/
T29G IP phones)
open-VPN = 2
Network->Advanced->VPN
(not applicable to
SIP-T19(P) E2 IP
phones)
wifi-active = 0
(2 for SIP VP-T49G IP
phones; only
applicable to SIP
Network->Wi-Fi->Wi-Fi Active
VP-T49G/SIP-T48G/
[Network-Wifi]
T48S/T46G/T46S/
T29G IP phones)
wifi-list = 0
(2 for SIP VP-T49G IP
phones; only
Network->Wi-Fi
applicable to SIP
40
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
VP-T49G/SIP-T48G/
T48S/T46G/T46S/
T29G IP phones)
wifi-label = 0
(only applicable to
SIP-T48G/T48S/T46G/
Network->Wi-Fi->Profile Name
T46S/T29G IP phones)
wifi-ssid = 0
(only applicable to
SIP-T48G/T48S/T46G/
Network->Wi-Fi->SSID
T46S/T29G IP phones)
wifi-mode = 0
(only applicable to
SIP-T48G/T48S/T46G/
Network->Wi-Fi->Security Mode
T46S/T29G IP phones)
[Network-Wifi]
wifi-type = 0
(only applicable to
SIP-T48G/T48S/T46G/
Network->Wi-Fi->Cipher Type
T46S/T29G IP phones)
wifi-psk = 0
(only applicable to
SIP-T48G/T48S/T46G/
Network->Wi-Fi->PSK
T46S/T29G IP phones)
Network->Wi-Fi->
wifi-edit = 2
(only applicable to SIP
VP-T49G IP phones)
wifi-status-detectiontimeout = 0
Network->Wi-Fi->Time-Out For Wi-Fi
(only applicable to SIP
Status Detection
VP-T49G IP phones)
[ DSSKey ]
(not applicable to
W56P IP DECT
linekey = 0
(not applicable to
SIP-T19(P) E2/CP860
Dsskey->Line Key (the whole page(s) for all
the line keys)
41
Configuration Guide for User Access Level
Section Header
phones)
Parameters and
Configuration Items on the Web User
Default Value
Interface
IP phones)
programmablekey = 0
Dsskey->Programable Key (the whole page)
extkey = 0
(only applicable to
SIP-T48G/T48S/T46G/
Dsskey->Ext Key (the whole page)
T46S/T29G/T27P/
T27G IP phones)
Dsskey->Line Key (for all the line keys on
each page)
line-key = 0
[ LineKey ]
(not applicable to
SIP-T19(P) E2/
CP860/W56P IP
phones)
Enable-Page-Tips = 0
(only applicable to
SIP-T46G/T46S/T29G/
T42G/T42S/T41P/
Dsskey->Line Key->Enable Page Tips
T41S/T27P/T27G IP
phones)
Label-Length = 0
(only applicable to SIP
VP-T49G/SIP-T48G/
Dsskey->Line Key->Label Length
T48S/T46G/T46S/
T29G IP phones)
Dsskey->Programable Key
[ ProgramKey ]
(not applicable to
W56P IP DECT
programmable-key =
0
phones)
[ ExtKey ]
(only applicable to
ext-key = 0
Dsskey->Ext Key
42
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
SIP-T48G/T48S/
T46G/T46S/T29G/
T27P/T27G IP
phones)
features-forward = 0
features-general = 0
features-audio = 0
Features->Forward&DND (the whole page)
Features->General Information (the whole
page)
Features->Audio (the whole page)
features-intercom = 0
(not applicable to
W56P IP DECT
Features->Intercom (the whole page)
phones)
features-transfer = 0
features-callpickup =
0
[ Features ]
Features->Transfer (the whole page)
Features->Call Pickup (the whole page)
features-remote = 2
(0 for SIP
VP-T49G/CP860 IP
Features->Remote Control (the whole
phones; not
page)
applicable to W56P IP
DECT phones)
features-phonelock =
0
Features->Phone Lock (the whole page)
features-acd = 2
(0 for SIP
VP-T49G/CP860 IP
phones; not
Features->ACD (the whole page)
applicable to W56P IP
DECT phones)
features-sms = 0
(not applicable to
W56P IP DECT
Features->SMS (the whole page)
phones)
43
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
features-actionurl = 2
(0 for SIP
VP-T49G/CP860 IP
phones; not
Features->Action URL (the whole page)
applicable to W56P IP
DECT phones)
features-bluetooth =
0
[ Features ]
(only applicable to SIP
VP-T49G/SIP-T48G/
Features->Bluetooth (the whole page)
T48S/T46G/T46S/
T29G IP phones)
features-powerled = 0
(not applicable to
Features->Power LED (the whole page)
CP860 IP phones)
features-notifypop =
0
(not applicable to
W56P IP DECT
Features->Notification Popups (the whole
page)
phones)
head-forward = 0
Features->Forward&DND->
forward-emergency =
0
(not applicable to
W56P IP DECT
Features->Forward&DND->Forward
->Forward Emergency
phones)
forward-authorized-n
[ Forward&DND ]
umbers = 0
(not applicable to
W56P IP DECT
Features->Forward&DND->Forward
->Forward Authorized Numbers
phones)
forward-mode = 0
(not applicable to
Features->Forward&DND->Forward
SIP-T19(P) E2/CP860
->Mode
IP phones)
forward-account = 0
Features->Forward&DND->Forward
44
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(not applicable to
->Account
SIP-T19(P) E2/CP860
IP phones)
Features->Forward&DND->Always
Forward
always-forward = 0
always-forward-enabl
Features->Forward&DND->Forward->Alwa
ed = 0
ys Forward->On/Off
always-forward-target
Features->Forward&DND->Forward->Alwa
=0
ys Forward->Target
always-forward-OnCo
de = 0
Features->Forward&DND->Forward->Alwa
(for neutral firmware
ys Forward->On Code
version only)
always-forward-OffCo
de = 0
Features->Forward&DND->Forward->Alwa
(for neutral firmware
ys Forward->Off Code
version only)
[ Forward&DND ]
Features->Forward&DND->Busy Forward
busy-forward = 0
busy-forward-enabled
Features->Forward&DND->Forward->Busy
=0
Forward->On/Off
busy-forward-target
Features->Forward&DND->Forward->Busy
=0
Forward->Target
busy-forward-OnCod
e=0
Features->Forward&DND->Forward->Busy
(for neutral firmware
Forward->On Code
version only)
busy-forward-OffCod
e=0
(for neutral firmware
Features->Forward&DND->Forward->Busy
Forward->Off Code
45
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
version only)
Features->Forward&DND->No Answer
Forward
NoAnswer-forward =
0
NoAnswer-forward-e
Features->Forward&DND->Forward->No
nabled = 0
Answer Forward->On/Off
NoAnswer-forward-ri
Features->Forward&DND->Forward->No
ngtimes = 0
Answer Forward->After Ring Time (0~120s)
NoAnswer-forward-ta
Features->Forward&DND->Forward->No
rget = 0
Answer Forward->Target
NoAnswer-forward-O
nCode = 0
Features->Forward&DND->Forward->No
(for neutral firmware
Answer Forward->On Code
version only)
[ Forward&DND ]
NoAnswer-forward-O
ffCode = 0
Features->Forward&DND->Forward->No
(for neutral firmware
Answer Forward->Off Code
version only)
Features->Forward&DND->DND
DND = 0
DND-Emergency = 0
(not applicable to
Features->Forward&DND->DND->DND
W56P IP DECT
Emergency
phones)
DND-Authorized-Nu
mbers = 0
(not applicable to
Features->Forward&DND->DND->DND
Authorized Numbers
46
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
W56P IP DECT
phones)
DND-mode = 0
(01 for SIP
VP-T49G/CP860/
W56P IP phones; not
Features->Forward&DND->DND->Mode
applicable to
SIP-T19(P) E2/CP860
IP phones)
DND-account = 0
(01 for SIP
VP-T49G/CP860/
W56P IP phones; not
applicable to
Features->Forward&DND->DND->Accoun
t
SIP-T19(P) E2/CP860
IP phones)
[ Forward&DND ]
DND-Status = 0
(01 for SIP
Features->Forward&DND->DND->DND
VP-T49G/CP860/
Status
W56P IP phones)
DND-OnCode = 0
(01 for SIP
VP-T49G/CP860/
Features->Forward&DND->DND->On
W56P IP phones; for
Code
neutral firmware
version only)
DND-OffCode = 0
(01 for SIP
VP-T49G/CP860/
Features->Forward&DND->DND->Off
W56P IP phones; for
Code
neutral firmware
version only)
Features->General Information->Call
[ General-Informat
ion ]
Waiting
call_waiting = 0
Features->General Information->Call
Waiting On Code (for neutral firmware
version only)
47
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Features->General Information->Call
Waiting Off Code (for neutral firmware
version only)
auto-redial = 0
(not applicable to
Features->General Information->Auto
W56P IP DECT
Redial
phones)
auto_redial_interval =
0
(not applicable to
W56P IP DECT
Features->General Information->Auto
Redial Interval(1~300s)
phones)
auto_redial_times = 0
(not applicable to
Features->General Information->Auto
W56P IP DECT
Redial Times (1~300)
phones)
key_as_send = 0
[ General-Informat
ion ]
reserve-pound = 2
Features->General Information->Key As
Send
Features->General Information->Reserve #
in User Name
hotline-number = 0
(not applicable to
Features->General Information->Hotline
W56P IP DECT
Number
phones)
hotline-delay = 0
(not applicable to
Features->General Information->Hotline
W56P IP DECT
Delay(0~10s)
phones)
busytone_delay = 0
Features->General Information->Busy Tone
Delay (Seconds)
return-code-refuse =
Features->General Information->Return
0
Code When Refuse
return-code-DND = 0
Features->General Information->Return
Code When DND
call_completion = 0
Features->General Information->Call
(not applicable to
Completion
48
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
W56P IP DECT
phones)
feature-key-synchroni
Features->General Information->Feature
sation = 0
Key Synchronization
TimeOut-for-DialNow
Features->General Information->Time Out
=0
for Dial Now Rule
RFC-2543-Hold = 2
Features->General Information->RFC 2543
Hold
use-outbound-in-dial
Features->General Information->Use
og = 2
Outbound Proxy In Dialog
IsDeal-180 = 2
Features->General Information->180 Ring
Workaround
logon-wizard = 2
(not applicable to
Features->General Information->Logon
CP860/W56P IP
Wizard
phones)
PswPrefix = 0
(2 for SIP
[ General-Informat
VP-T49G/CP860 IP
ion ]
phones; not
Features->General Information->PswPrefix
applicable to W56P IP
DECT phones)
PswLength = 0
(2 for SIP
VP-T49G/CP860 IP
Features->General
phones; not
Information->PswLength
applicable to W56P IP
DECT phones)
PswDial = 0
(2 for SIP
VP-T49G/CP860 IP
phones; not
Features->General Information->PswDial
applicable to W56P IP
DECT phones)
SaveCallHistory = 2
Features->General Information->Save Call
Log
49
Configuration Guide for User Access Level
Parameters and
Configuration Items on the Web User
Default Value
Interface
SuppressDTMFDisplay
Features->General Information->Suppress
=1
DTMF Display
SuppressDTMFDisplay
Features->General Information->Suppress
Delay = 1
DTMF Display Delay
Section Header
play-local-DTMF-tone
=0
(not applicable to
W56P IP DECT
Features->General Information->Play Local
DTMF Tone
phones)
DTMFRepetition = 0
(not applicable to
Features->General Information->DTMF
W56P IP DECT
Repetition
phones)
MulticastCodec = 0
(not applicable to
Features->General Information->Multicast
SIP-T19(P) E2/W56P
Codec
IP phones)
PlayHoldTone = 0
[ General-Informat
ion ]
(not applicable to
Features->General Information->Play Hold
W56P IP DECT
Tone
phones)
PlayHoldToneDelay =
0
(not applicable to
W56P IP DECT
Features->General Information->Play Hold
Tone Delay
phones)
AllowMute = 0
(not applicable to
Features->General Information->Allow
W56P IP DECT
Mute
phones)
DualHeadset = 0
(1 for SIP VP-T49G IP
phones; not
Features->General Information->Dual
applicable to
Headset
CP860/W56P IP
phones)
50
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
AutoAnswerDelay = 0
(not applicable to
Features->General Information->Auto
W56P IP DECT
Answer Delay(1~4s)
phones)
enable-auto-answer-t
one = 0
(not applicable to
W56P IP DECT
Features->General Information->Enable
Auto Answer Tone
phones)
HeadsetPrior = 0
(not applicable to
Features->General Information->Headset
CP860/W56P IP
Prior
phones)
DTMFReplaceTran = 0
(not applicable to
Features->General Information->DTMF
W56P IP DECT
Replace Tran
phones)
TranSendDTMF = 1
(not applicable to
Features->General Information->Tran Send
W56P IP DECT
DTMF
phones)
[ General-Informat
ion ]
SendPoundKey = 0
(not applicable to
Features->General Information->Send
W56P IP DECT
Pound Key
phones)
FwdInternational = 0
Features->General Information->Fwd
International
Diversion-History-Info
Features->General
=1
Information->Diversion/History-Info
allow-trans-exist-call
=0
(not applicable to
W56P/SIP
VP-T49G/SIP-T48G/
Features->General Information->Allow
Trans Exist Call
T48S/T46G/T46S/
T29G IP phones)
51
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
blf-led-mode = 0
(not applicable to
W56P/SIP
VP-T49G/SIP-T19(P)
Features->General Information->BLF LED
Mode
E2/CP860 IP phones)
ReLogOffTime = 2
call-number-filter = 0
Features->General Information->Auto
Logout Time(1~1000min)
Features->General Information->Call
Number Filter
Use_Logo = 0
(not applicable to
W56P/SIP
VP-T49G/SIP-T48G/
Features->General Information->Use Logo
T48S/T46G/T46S/
T29G IP phones)
upload_logo = 0
(not applicable to
[ General-Informat
ion ]
W56P/SIP
Features->General Information->Upload
VP-T49G/SIP-T48G/
Logo
T48S/T46G/T46S/
T29G IP phones)
sip-trust-control = 2
Features->General Information->Accept
SIP Trust Server Only
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
allow-IP-call = 0
Features->General Information->Allow IP
Call
SIP VP-T49G:
Account->SIP IP Call->Allow IP Call
IP-direct-auto-answer
=0
(not applicable to
W56P IP DECT
phones)
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
Features->General Information->IP Direct
Auto Answer
SIP VP-T49G:
52
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Account->SIP IP Call->IP Direct Auto
Answer
calllog-show-num = 0
(not applicable to
Features->General Information->Call List
W56P IP DECT
Show Number
phones)
voicemail-tone = 0
DHCP-hostname = 0
reboot-in-talking = 0
Features->General Information->Voice
Mail Tone
Features->General Information->DHCP
Hostname
Features->General Information->Reboot In
Talking
Hide-Feature-AccessCodes = 0
(not applicable to
W56P IP DECT
Features->General Information->Hide
Feature Access Codes
phones)
[ General-Informat
ion ]
display-method-on-di
Features->General Information->Display
aling = 2
Method on Dialing
auto-linekeys = 1
(not applicable to
SIP-T19(P) E2/
CP860/W56P IP
Features->General Information->Auto
Linekeys
phones)
end-call-onhook = 0
(only applicable to
Features->General Information->End Call
W56P IP DECT
On Hook
phones)
call-waiting-tone = 0
Features->Audio->Call Waiting Tone
53
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
button-sound = 0
(not applicable to
W56P IP DECT
Features->Audio->Key Tone
phones)
send-sound = 0
(not applicable to
W56P IP DECT
Features->Audio->Send Tone
phones)
redial_tone = 0
(not applicable to
W56P IP DECT
Features->Audio->Redial Tone
phones)
headset-send-volume
=1
(not applicable to
CP860/W56P IP
Features->Audio->Headset Send Volume
(-50~50)
phones)
[ Features-Audio]
handset-send-volume
=1
(not applicable to
CP860/W56P IP
Features->Audio->Handset Send Volume
(-50~50)
phones)
handfree-send-volum
e=1
(not applicable to
CP860/W56P IP
Features->Audio->Handfree Send Volume
(-50~50)
phones)
Ringer_Dev = 0
(not applicable to
Features->Audio->Ringer Device for
CP860/W56P IP
Headset
phones)
[ Features-Interco
m]
(not applicable to
W56P IP DECT
phones)
allow-intercom = 0
Features->Intercom->Allow Intercom
intercom-mute = 0
Features->Intercom->Intercom Mute
intercom-tone = 0
Features->Intercom->Intercom Tone
intercom-barge = 0
Features->Intercom->Intercom Barge
54
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
semi-attend-transfer
Features->Transfer->Semi-Attended
=0
Transfer
blind-tran-onhook =
Features->Transfer->Blind Transfer On
0
Hook
Semi-Attend-Trans-O
Features->Transfer->Attended Transfer On
nHook = 0
Hook
transfer-on-conferenc
[ Features-Transfer
]
e-hang-up = 0
(not applicable to
W56P IP DECT
Features->Transfer->Transfer on
Conference Hang up
phones)
TransferModeViaDssk
ey = 0
(not applicable to
Features->Transfer->Transfer Mode Via
SIP-T19(P) E2/
Dsskey
CP860/W56P IP
phones)
Features->Call Pickup->Call Pickup
Call-Pickup = 0
[ Features-Callpick
up ]
Features->Call Pickup->Call Park
Call-Park = 0
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
[ Features-Remote
]
(not applicable to
W56P IP DECT
phones)
pushxml-server-addr
Features->Remote Control->Push XML
=2
Server IP Address
XMLSIPNotify = 2
Features->Remote Control->SIP Notify
XMLBlockInCalling =
2
(1 for SIP
Features->Remote Control->Block XML in
Calling
55
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
VP-T49G/CP860/
W56P IP phones)
ActionURILimitIP = 2
Features->Remote Control->Action URI
Allow IP List
CSTAControl = 2
(not applicable to SIP
VP-T49G/CP860/
Features->Remote Control->CSTA Control
W56P IP phones)
Lock_Enable = 0
(2 for SIP
VP-T49G/CP860 IP
Features->Phone Lock->Phone Lock Enable
phones)
keyboard_lock = 0
(2 for SIP
VP-T49G/CP860 IP
Features->Phone Lock->Phone Lock Type
phones)
Phone_Unlock_PIN =
[ Features-Lock ]
(not applicable to
W56P IP DECT
phones)
0
(2 for SIP
VP-T49G/CP860 IP
Features->Phone Lock->Phone Unlock
PIN(0~15 Digit)
phones)
Phone_lock_time_out
=0
(2 for SIP
VP-T49G/CP860 IP
Features->Phone Lock->Phone Lock Time
Out(0~3600s)
phones)
emergency_setting =
0
(2 for SIP
Features->Phone Lock->Emergency
VP-T49G/CP860 IP
phones)
[ Features-ACD ]
(not applicable to
W56P IP DECT
phones)
[ Features-SMS ]
ACD-auto-available =
Features->ACD->ACD->ACD Auto
2
Available
ACD-auto-available-ti
Features->ACD->ACD->ACD Auto
mer = 2
Available Timer(0~120s)
send-sms = 0
Features->SMS->
56
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(only applicable to
SIP VP-T49G IP
phones)
[ Features-ActionU
RL ]
(not applicable to
W56P IP DECT
phones)
setup-complete = 2
Features->Action URL->Setup Completed
log-on = 2
Features->Action URL->Registered
log-off = 2
Features->Action URL->Unregistered
register-fail = 2
Features->Action URL->Register Failed
off-hook = 2
Features->Action URL->Off Hook
on-hook = 2
Features->Action URL->On Hook
incoming-call = 2
Features->Action URL->Incoming Call
outgoing-call = 2
Features->Action URL->Outgoing Call
call-establish = 2
Features->Action URL->Established
Call-Terminated = 2
Features->Action URL->Terminated
DND-On = 2
Features->Action URL->Open DND
DND-Off = 2
Features->Action URL->Close DND
Forward-On-Code = 2
Forward-Off-Code = 2
Busy-Forward-On = 2
Features->Action URL->Open Always
Forward
Features->Action URL->Close Always
Forward
Features->Action URL->Open Busy
Forward
Busy-Forward-Off = 2
Features->Action URL->Close Busy Forward
No-Answer-Forward-
Features->Action URL->Open NoAnswer
On = 2
Forward
No-Answer-Forward-
Features->Action URL->Close NoAnswer
Off = 2
Forward
TransferCall = 2
Features->Action URL->Transfer Call
Blind-transfer-call = 2
Features->Action URL->Blind Transfer
Attended-transfer-call
=2
Features->Action URL->Attended Transfer
57
Configuration Guide for User Access Level
Section Header
[ Features-ActionU
RL ]
(not applicable to
W56P IP DECT
phones)
Parameters and
Configuration Items on the Web User
Default Value
Interface
Hold = 2
Features->Action URL->Hold
Unhold = 2
Features->Action URL->UnHold
Mute = 2
Features->Action URL->Mute
Unmute = 2
Features->Action URL->UnMute
Missed-call = 2
Features->Action URL->Missed Call
IPChange = 2
Features->Action URL->IP Changed
IdletoBusy = 2
Features->Action URL->Idle To Busy
BusytoIdle = 2
Features->Action URL->Busy To Idle
RejectIncomingCall =
Features->Action URL->Reject Incoming
2
Call
AnswerNewInCall = 2
Features->Action URL->Answer New-In
Call
TransferFailed = 2
Features->Action URL->Transfer Failed
TransferFinished = 2
Features->Action URL->Transfer Finished
ForwardIncomingCall
Features->Action URL->Forward Incoming
=2
Call
Features->Action URL->UCServer
UCServer = 2
(only appear when the parameter
“action_url.is_ume” is set to 1)
Features->Action URL->Report IP
ReportIP = 2
(only appear when the parameter
“action_url.is_ume” is set to 1)
AutopFinish = 2
Features->Action URL->Autop Finish
OpenCallWait = 2
Features->Action URL->Open Call Waiting
CloseCallWait = 2
Features->Action URL->Close Call Waiting
Headset = 2
(not applicable to
Features->Action URL->Headset
CP860 IP phones)
Handfree = 2
(not applicable to
Features->Action URL->Handfree
CP860 IP phones)
CancelCallOut = 2
Features->Action URL->Cancel Call Out
58
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
RemoteBusy = 2
Features->Action URL->Remote Busy
CallRemoteCanceled
Features->Action URL->Call Remote
=2
Canceled
bluetooth-active = 0
[ Features-Bluetoo
th ]
(only applicable to SIP
VP-T49G/SIP-T48G/
Features->Bluetooth->Bluetooth Active
T48S/T46G/T46S/
T29G IP phones)
common-power-light
Features->Power LED->Common Power
-on = 0
Light On
ring-power-light-flash
Features->Power LED->Ringing Power
=0
Light Flash
mail-power-light-flas
h=0
(only applicable to
W56P IP DECT
Features->Power LED->Voice/Text Mail
Power Light Flash
phones)
miss-call-light-flash =
[ Features-PowerL
ED ]
(not applicable to
CP860 IP phones)
0
(only applicable to
W56P IP DECT
Features->Power LED->Miss Call Power
Light Flash
phones)
mute-power-light-flas
h=0
(not applicable to
W56P IP DECT
Features->Power LED->Mute Power Light
Flash
phones)
hold-power-light-flas
h=0
(not applicable to
W56P IP DECT
Features->Power LED->Hold/Held Power
Light Flash
phones)
talk-power-light-flash
=0
Features->Power LED->Talk/Dial Power
(not applicable to
Light On
W56P IP DECT
59
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
phones)
[ Features-PowerL
ED ]
misscall-power-light-f
lash = 0
(not applicable to
(not applicable to SIP
CP860 IP phones)
VP-T49G/CP860/W56
Features->Power LED->MissCall Power
Light Flash
P IP phones)
[ Features-NotifyP
op ]
(not applicable to
W56P IP DECT
phones)
Display-Voice-Mail-P
Features->Notification Popups->Display
opup = 0
Voice Mail Popup
Display-Missed-Call-P
Features->Notification Popups->Display
opup = 0
Missed Call Popup
Display-Forward-Call-
Features->Notification Popups->Display
Popup = 0
Forward Call Popup
Display-Text-Message
Features->Notification Popups->Display
-Popup = 0
Text Message Popup
settings-preference =
0
settings-datetime = 0
settings-calldisplay =
0
settings-upgrade = 0
Settings->Preference (the whole page)
Settings->Time & Date (the whole page)
Settings->Call Display (the whole page)
Settings->Upgrade (the whole page)
settings-autop = 2
(0 for SIP
[ Settings ]
VP-T49G/CP860/
Settings->Auto Provision (the whole page)
W56P IP phones)
settings-config = 0
Settings->Configuration (the whole page)
settings-dialplan = 2
(0 for SIP
VP-T49G/CP860/
Settings->Dial Plan (the whole page)
W56P IP phones)
settings-voice = 2
(0 for SIP
VP-T49G/CP860/
Settings->Voice (the whole page)
W56P IP phones)
settings-ring = 2
Settings->Ring (the whole page)
60
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(1 for SIP
VP-T49G/CP860 IP
phones; not
applicable to W56P IP
DECT phones)
settings-tones = 2
(0 for SIP
VP-T49G/CP860/
Settings->Tones (the whole page)
W56P IP phones)
settings-softkey = 2
(not applicable to
W56P IP DECT
Settings->Softkey Layout (the whole page)
phones)
[ Settings ]
settings-tr069 = 2
Settings->TR069 (the whole page)
settings-voicemonitor
ing = 2
(0 for SIP
VP-T49G/CP860 IP
phones; not
Settings->Voice Monitoring (the whole
page)
applicable to W56P IP
DECT phones)
settings-sip = 2
(0 for SIP
VP-T49G/CP860/
Settings->SIP (the whole page)
W56P IP phones)
settings-powersaving
=0
(only applicable to SIP
VP-T49G/SIP-T48G/
Settings->Power Saving (the whole page)
T48S/T46G/T46S/
T29G IP phones)
settings-camera = 0
(only applicable to SIP
Settings->Camera (the whole page)
VP-T49G IP phones)
settings-video = 0
(only applicable to SIP
Settings->Video (the whole page)
61
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
VP-T49G IP phones)
SIP VP-T49G/CP860/W56P:
Settings->Preference->Language
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
web-language = 0
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2:
live-dialpad = 0
(not applicable to
W56P IP DECT
Settings->Preference->Live Dialpad
phones)
inter-digit-time = 0
[ Settings-Preferen
ce ]
(not applicable to
Settings->Preference->Inter Digit
W56P IP DECT
Time(1~14s)
phones)
transparency = 0
(only applicable to
SIP-T48G/S IP
Settings->Preference->Transparency
phones)
UnusedBackLight = 0
(only applicable to SIP
VP-T49G/SIP-T48G/
T48S/T46G/T46S/
Settings->Preference->Backlight Inactive
Level (Unused BackLight)
T29G IP phones)
backlight = 0
(only applicable to SIP
VP-T49G/SIP-T48G/T4
8S/T46G/T46S/T29G/
Settings->Preference->Backlight Active
Level (Active Backlight Level)
T27P/T27G IP phones)
BacklightTime = 0
(not applicable to
Settings->Preference->Backlight
SIP-T19(P) E2 and
Time(seconds)
W56P IP phones)
contrast_ctrl = 0
(only applicable to
Settings->Preference->Contrast
62
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
CP860/SIP-T40P/T27P
/T27G/T23P/T23G/
T21(P) E2/T19(P) E2 IP
phones)
watchdog = 2
Settings->Preference->Watch Dog
ring_type_setting = 0
(not applicable to
Settings->Preference->Ring Type
W56P IP DECT
Settings->Preference->Upload Ringtone
phones)
Wallpaper = 0
(only applicable to SIP
VP-T49G/SIP-T48G/
T48S/T46G/T46S/
T29G IP phones)
Settings->Preference->Wallpaper
Settings->Preference->Upload
Wallpaper(480*272)
Settings->Preference->Wallpaper with
DSSkey unfold (only applicable to
SIP-T48G/S IP phones)
screen-saver-wait-tim
[ Settings-Preferen
ce ]
e=0
Settings->Preference->Screensaver Wait
(only applicable to SIP
Time
VP-T49G IP phones)
screen-saver-type = 0
(only applicable to SIP
VP-T49G IP phones)
ScreenSaver = 0
Settings->Preference->Screensaver Type
Settings->Preference->Screensaver
Settings->Preference->
(only applicable to
SIP-T48G/T48S/T46G/
T46S/T29G IP phones)
ScreenSaverUpload =
0
Settings->Preference->Upload Screensaver
(only applicable to
(only appear when the parameter
SIP-T48G/T48S/T46G/
“screensaver.type” is set to 1.)
T46S/T29G IP phones)
[ Time&Date ]
DHCP-Time = 0
Settings->Time & Date->DHCP Time
manual-time = 0
Settings->Time & Date->Manual Time
time_zone = 0
Settings->Time & Date->Time Zone
daylight-time = 0
Settings->Time & Date->Daylight Saving
63
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Time
location = 0
Settings->Time & Date->Location
time_type = 0
Settings->Time & Date->Fixed Type
daylight_date = 0
offset = 0
NTP_priority = 0
Settings->Time & Date->Start Date
Settings->Time & Date->End Date
Settings->Time & Date->Offset(minutes)
Settings->Time & Date->NTP by DHCP
Priority
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
prim_server = 0
Settings->Time & Date->Primary Server
SIP VP-T49G:
Settings->Time & Date->Primary NTP
Server
[ Time&Date ]
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2/CP860/W56P:
sec_server = 0
Settings->Time & Date->Secondary Server
SIP VP-T49G:
Settings->Time & Date->Secondary NTP
Server
update_interval = 0
manual-time-settings
Settings->Time &
Date->Synchronism(15~86400s)
Settings->Time & Date->Manual Time
=0
time_format_setting =
0
date_format_setting =
0
Settings->Time & Date->Time Format
Settings->Time & Date->Date Format
Display-Contact-Phot
o=0
Settings->Call Display->Display Contact
(only applicable to SIP
Photo
VP-T49G/SIP-T48G/
64
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
[ Settings-CallDisp
T48S/T46G/T46S/
lay ]
T29G IP phones)
Incoming-Call-Ringer-
Settings->Call Display->Display Called
Animation = 0
Party Information
Call-Display-Method
Settings->Call Display->Call Information
=0
Display Method
Settings->Upgrade->Version
version_info = 0
SIP VP-T49G/CP860/W56P:
reset_to_factory = 2
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
Settings->Upgrade->Reset to Factory
Setting
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
T21(P) E2/T19(P) E2:
Settings->Upgrade->Reset to factory
reset = 0
(2 for SIP
VP-T49G/CP860/
Settings->Upgrade->Reset
W56P IP phones)
reset_local_settings =
0
[ Settings-Upgrad
e]
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
reset_nonstatic_settin
gs = 0
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
reset_static_settings =
2
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
Settings->Upgrade->Reset local settings
(only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
Settings->Upgrade->Reset non-static
settings (only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
Settings->Upgrade->Reset static settings
(only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
65
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
reset_userdata = 0
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
Settings->Upgrade->Reset userdata &
local config (only appear when the
parameter
“static.auto_provision.custom.protect” is set
to 1.)
reset_local_config = 0
Settings->Upgrade->Reset Local
(only applicable to SIP
Configuration (only appear when the
VP-T49G/CP860/
parameter “auto_provision.custom.protect”
W56P IP phones)
is set to 1.)
reboot_device = 0
Settings->Upgrade->Reboot
SIP VP-T49G/CP860/W56P:
Settings->Upgrade->Upgrade
[ Settings-Upgrad
e]
upgrade_firmware = 0
(1 for SIP
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41
VP-T49G/CP860/
P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/
W56P IP phones)
T21(P) E2/T19(P) E2:
Settings->Upgrade->Select and Upgrade
Firmware
upgrade_handset_firm
ware = 1
(only applicable to
W56P IP DECT
Settings->Upgrade->Select and Upgrade
Handset Firmware
phones)
pnp-active = 2
Settings->Auto Provision->PNP Active
dhcp-active = 2
Settings->Auto Provision->DHCP Active
[ Settings-AutoPro
vision ]
custom-option = 2
Settings->Auto Provision->Custom
Option(128~254)
DHCP-Option-Value
Settings->Auto Provision->DHCP Option
=2
Value
server-URL = 2
Settings->Auto Provision->Server URL
account = 2
Settings->Auto Provision->User Name
password = 2
Settings->Auto Provision->Password
attempt-expired-time
Settings->Auto Provision->Attempt
66
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
=2
common-AES-key = 2
Expired Time(s)
Settings->Auto Provision->Common AES
Key
MAC-Oriented-AES-k
Settings->Auto Provision->MAC-Oriented
ey = 2
AES Key
zero_active = 2
(not applicable to
W56P IP DECT
Settings->Auto Provision->Zero Active
phones)
wait_time = 2
(not applicable to
Settings->Auto Provision->Wait
W56P IP DECT
Time(1~100s)
Settings-AutoProv
phones)
ision ]
poweron-active = 2
Settings->Auto Provision->Power On
repeatly-active = 2
Settings->Auto Provision->Repeatedly
repeat-interval = 2
weekly-active = 2
Settings->Auto
Provision->Interval(Minutes)
Settings->Auto Provision->Weekly
weekly-upgrade-inter
val = 2
(not applicable to SIP
VP-T49G/CP860/
Settings->Auto Provision->Weekly
Upgrade Interval(0~12week)
W56P IP phones)
inactivity-time-expire
=2
(not applicable to SIP
VP-T49G/CP860/
Settings->Auto Provision->Inactivity Time
Expire(0~120min)
W56P IP phones)
autop-time = 2
Settings->Auto Provision->Time
day-of-week = 2
Settings->Auto Provision->Day of Week
67
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
flexible-switch = 2
[ Settings-AutoPro
vision ]
(not applicable to SIP
Settings->Auto Provision->Flexible Auto
VP-T49G/CP860/
Provision
W56P IP phones)
flexible-interval = 2
(not applicable to SIP
Settings->Auto Provision->Flexible Interval
VP-T49G/CP860/
Days
W56P IP phones)
flexible-autoptime = 2
(not applicable to SIP
VP-T49G/CP860/
Settings->Auto Provision->Flexible Time
W56P IP phones)
btn-autop-now = 2
Settings->Auto Provision->
opt-configfile = 0
Settings->Configuration->Export or Import
(1 for SIP
Configuration
VP-T49G/CP860/
W56P IP phones)
Settings->Configuration->Import Factory
Configuration (for SIP
[ Settings-Config ]
opt-factory-configfile
VP-T49G/CP860/W56P: only appear when
=0
the parameter
(2 for SIP
“features.custom_factory_config.enable” is
VP-T49G/CP860/
set to 1; for other IP phones: only appear
W56P IP phones)
when the parameter
“static.features.custom_factory_config.enabl
e” is set to 1)
export-cfg-config-file
=0
Settings->Configuration->Export CFG
(2 for SIP
Configuration File
VP-T49G/CP860/
68
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
W56P IP phones)
import-cfg-config-file
=0
(2 for SIP
VP-T49G/CP860/
Settings->Configuration->Import CFG
Configuration File
W56P IP phones)
Settings->Configuration->Pcap Feature
Settings->Configuration->Packet Capture
Count (only applicable to SIP VP-T49G IP
phones)
pcap_trace = 0
Settings->Configuration->Packet Capture
(1 for SIP
Clip Bytes (only applicable to SIP VP-T49G
VP-T49G/CP860/
IP phones)
W56P IP phones)
Settings->Configuration->Pcap Filter Type
(only applicable to SIP VP-T49G IP phones)
Settings->Configuration->Packet Filter
String (only applicable to SIP VP-T49G IP
phones)
syslog = 1
[ Settings-Config ]
(only applicable to SIP
Settings->Configuration->Export System
VP-T49G/CP860/
Log
W56P IP phones)
SystemlogLevel = 2
(only applicable to SIP
Settings->Configuration->System Log
VP-T49G/CP860/
Level
W56P IP phones)
Local_Logging = 0
Settings->Configuration->Local Logging
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
Local_Log_Switch = 0
(not applicable to SIP
Settings->Configuration->Local
VP-T49G/CP860/
Logging->Enable Local Logging
W56P IP phones)
Local_Log_Level = 0
Settings->Configuration->Local
69
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(not applicable to SIP
Logging->Local Log Level
VP-T49G/CP860/
W56P IP phones)
Local_Log_Max_File_Si
ze = 0
(not applicable to SIP
VP-T49G/CP860/
Settings->Configuration->Local
Logging->Max Log File Size (1024-2048KB)
W56P IP phones)
Local_Log_Export = 0
(not applicable to SIP
Settings->Configuration->Local
VP-T49G/CP860/
Logging->Export Local Log
W56P IP phones)
Syslog_Switch = 2
[ Settings-Config ]
(not applicable to SIP
Settings->Configuration->Syslog->Enable
VP-T49G/CP860/
Syslog Feature
W56P IP phones)
Syslog_Server = 2
Settings->Configuration->Syslog->Syslog
(not applicable to SIP
Server
VP-T49G/CP860/
Settings->Configuration->Syslog->Syslog
W56P IP phones)
Server->Port
Syslog_Transport_Typ
e=2
(not applicable to SIP
VP-T49G/CP860/
Settings->Configuration->Syslog->Transp
ort Type
W56P IP phones)
Syslog_Level = 2
(not applicable to SIP
Settings->Configuration->Syslog->Syslog
VP-T49G/CP860/
Level
W56P IP phones)
Syslog_Facility = 2
(not applicable to SIP
Settings->Configuration->Syslog->Syslog
VP-T49G/CP860/
Facility
W56P IP phones)
Syslog_Prepend_Mac
Settings->Configuration->Syslog->Prepen
=2
d MAC in Syslog
70
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(not applicable to SIP
VP-T49G/CP860/
W56P IP phones)
[ Settings-Config ]
ExportAllDiagnosticFil
es = 2
(not applicable to SIP
VP-T49G/CP860/
Settings->Configuration->Export All
Diagnostic Files
W56P IP phones)
replace-rule = 0
dial-now = 0
area-code = 0
block-out = 0
Settings->Dial Plan->Replace Rule (the
whole page)
Settings->Dial Plan->Dial Now (the whole
page)
Settings->Dial Plan->Area Code (the whole
page)
Settings->Dial Plan->Block Out (the whole
page)
Settings->Dial Plan->Replace Rule->Prefix
Settings->Dial Plan->Replace
replace-rule-control =
Rule->Replace
0
Settings->Dial Plan->Replace
Rule->Account (not applicable to
[ Settings-DialPlan
SIP-T19(P) E2/CP860 IP phones)
]
Settings->Dial Plan->Dial Now->Rule
dial-now-control = 0
Settings->Dial Plan->Dial Now->Account
(not applicable to SIP-T19(P) E2/CP860 IP
phones)
Settings->Dial Plan->Area Code->Code
Settings->Dial Plan->Area Code->Min
Length (1-15)
area-code-control = 0
Settings->Dial Plan->Area Code->Max
Length (1-15)
Settings->Dial Plan->Area Code->Account
(not applicable to SIP-T19(P) E2/CP860 IP
phones)
block-out-control = 0
Settings->Dial Plan->Block Out->BlockOut
NumberX(X=1,2,…,10)
71
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
[ Settings-DialPlan
Settings->Dial Plan->Block Out->Account
]
(not applicable to SIP-T19(P) E2/CP860 IP
phones)
echo-cancellation = 2
Settings->Voice->Echo Cancellation
(0 for SIP
VP-T49G/CP860/
W56P IP phones)
[ Settings-Voice ]
jitter-buffer = 2
Settings->Voice->JITTER BUFFER
(0 for SIP
VP-T49G/CP860/
W56P IP phones)
[ Settings-Ring ]
personal-ring = 2
(not applicable to
(1 for SIP
Settings->Ring->Internal Ringer Text
W56P IP DECT
VP-T49G/CP860 IP
Settings->Ring->Internal Ringer File
phones)
phones)
Settings->Tones->Select Country
Settings->Tones->Dial
Settings->Tones->Secondary Dial
Settings->Tones->Ring Back
Settings->Tones->Busy
Settings->Tones->Congestion (not
applicable to W56P IP DECT phones)
tone-items = 2
(0 for SIP
VP-T49G/CP860/
W56P IP phones)
[ Settings-Tones ]
Settings->Tones->Call Waiting
Settings->Tones->Dial Recall (not
applicable to W56P IP DECT phones)
Settings->Tones->Info (not applicable to
W56P IP DECT phones)
Settings->Tones->Stutter (not applicable
to W56P IP DECT phones)
Settings->Tones->Message (not applicable
to W56P IP DECT phones)
Settings->Tones->Auto Answer (not
applicable to W56P IP DECT phones)
tone-country = 2
(not applicable to SIP
Settings->Tones->Select Country
72
Configuration Guide for User Access Level
Section Header
[ Settings-Tones ]
Parameters and
Configuration Items on the Web User
Default Value
Interface
VP-T49G/CP860/
W56P IP phones)
Custom_SoftKey = 2
SoftKey_Type = 2
Settings->Softkey Layout->Custom Softkey
Settings->Softkey Layout->Call States
Settings->Softkey Layout->
[ Softkey ]
(not applicable to
W56P IP DECT
phones)
[ TR069 ]
SoftKey_Select = 2
head = 2
Settings->TR069->
EnableTR069 = 2
Settings->TR069->Enable TR069
ACSUsername = 2
Settings->TR069->ACS Username
ACSPassword = 2
Settings->TR069->ACS Password
ACSURL = 2
Settings->TR069->ACS URL
EnablePeriodicInform
=2
Settings->TR069->Enable Periodic Inform
PeriodicInformInterval
Settings->TR069->Periodic Inform Interval
=2
(seconds)
RequestUsername = 2
RequestPassword = 2
Settings->TR069->Connection Request
Username
Settings->TR069->Connection Request
Password
RTCP-Session-Report
Settings->Voice Monitoring->VQ RTCP-XR
=2
Session Report
RTCP-Interval-Report
Settings->Voice Monitoring->VQ RTCP-XR
[ Settings-VoiceM
=2
Interval Report
onitoring ]
RTCP-Interval-Period
Settings->Voice Monitoring->Period for
=2
Interval Report
RTCP-Warning-Moslq
Settings->Voice Monitoring->Warning
=2
threshold for Moslq
73
Configuration Guide for User Access Level
Section Header
[ Settings-VoiceM
onitoring ]
Parameters and
Configuration Items on the Web User
Default Value
Interface
RTCP-Critical-Moslq =
Settings->Voice Monitoring->Critical
2
threshold for Moslq
RTCP-Warning-Delay
Settings->Voice Monitoring->Warning
=2
threshold for Delay
RTCP-Critical-Delay =
Settings->Voice Monitoring->Critical
2
threshold for Delay
Display-VQReport-On
Settings->Voice Monitoring->Display
-Web = 2
Report options on Web
Display-VQReport-On
Settings->Voice Monitoring->Display
-UI = 2
Report options on phone
Voice-RTCP-XR-REPO
RT = 2
(not applicable to SIP
VP-T49G/CP860/
Settings->Voice Monitoring->Voice
RTCP-XR Report
W56P IP phones)
Settings->Voice Monitoring->Report
options on phone
RTCP-Report-Options
=2
Settings->SIP->SIP Session Timer T1
(0.5~10s)
sip-session-timer = 2
[ Settings-SIP ]
Settings->SIP->SIP Session Timer T2
(2~40s)
Settings->SIP->SIP Session Timer T4
(2.5~60s)
local-SIP-port = 2
Settings->SIP->Local SIP Port
TLS-SIP-Port = 2
Settings->SIP->TLS SIP Port
Settings->Camera->Scene Mode
[ Settings-Camera
]
scene-mode = 2
(only applicable to
SIP VP-T49G IP
phones)
manual-settings = 2
Settings->Camera->Manual Settings (only
appear when the parameter
74
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
“camera.scene_mode” is set to 0)
[ Settings-Camera
]
(only applicable to
SIP VP-T49G IP
phones)
Settings->Camera->Exposure
exposure = 2
status-bar-icon = 2
[ Settings-Video ]
(only applicable to
SIP VP-T49G IP
phones)
Settings->Camera->Camera Icon on Status
Bar
video-active = 0
Settings->Video->Video Active
auto-start-video = 0
Settings->Video->Auto Start Video
auto-answer-video-m
Settings->Video->Auto Answer Video
ute = 0
Mute
uplink-bandwidth = 2
Settings->Video->Uplink Bandwidth
downlink-bandwidth
=2
Settings->Video->Downlink Bandwidth
enable = 2
(not applicable to SIP
Settings->Power Saving->Power Saving
VP-T49G IP phones)
Settings->Power Saving->Office Hour
[ Settings-PowerS
aving ]
(only applicable to
office_hour = 0
SIP
(2 for SIP VP-T49G IP
VP-T49G/SIP-T48
phones)
G/T48S/T46G/
T46S/T29G IP
phones)
office_Monday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Monday
phones)
75
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
office_Tuesday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Tuesday
phones)
office_Wednesday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Wednesday
phones)
office_Thursday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Thursday
phones)
office_Friday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Friday
phones)
office_Saturday = 0
(2 for SIP VP-T49G IP
Settings->Power Saving->Saturday
phones)
[ Settings-PowerS
aving ]
(only applicable to
SIP
office_Sunday = 0
(2 for SIP VP-T49G IP
phones)
Settings->Power Saving->Idle TimeOut
VP-T49G/SIP-T48
G/T48S/T46G/
T46S/T29G IP
phones)
Settings->Power Saving->Sunday
idle_timeout = 0
(minutes)
(2 for SIP VP-T49G IP
phones)
office_timeout = 0
(2 for SIP VP-T49G IP
phones)
off_timeout = 0
(2 for SIP VP-T49G IP
phones)
Settings->Power Saving->Office Hour Idle
TimeOut
Settings->Power Saving->Off Hour Idle
TimeOut
user_input_ext_timeo
ut = 0
Settings->Power Saving->User Input
(2 for SIP VP-T49G IP
Extension Idle TimeOut
phones)
76
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
contacts-basic = 0
Directory->Local Directory (the whole
page)
contacts-remote = 1
(0 for SIP
Directory->Remote Phone Book (the whole
VP-T49G/CP860/
page)
W56P IP phones)
contacts-callinfo = 0
(not applicable to
Directory->Phone Call Info (the whole
W56P IP DECT
page)
phones)
[ Contacts ]
contacts-LDAP = 1
(0 for SIP
VP-T49G/CP860/
W56P IP phones; not
Directory->LDAP (the whole page)
applicable to
SIP-T19(P) E2 IP
phones)
contacts-multicastIP
=1
(0 for SIP
VP-T49G/CP860 IP
Directory->Multicast IP (the whole page)
phones; not
applicable to W56P IP
DECT phones)
[ Contacts-Basic ]
(only applicable to
W56P IP DECT
contacts-favorite = 0
Directory->Setting (the whole page)
download-contacts =
Directory->Local Directory->File Template
0
Download
importcontacts = 0
phones)
export-contacts = 0
Directory->Local Directory->Import
Contacts
Directory->Local Directory->Export
Contacts
contact-list = 0
(not applicable to
W56P IP DECT
Directory->Local Directory
phones)
77
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Directory->Local Directory->
all-contacts-control =
[ LocalPhoneBook
0
]
(not applicable to
W56P IP DECT
phones)
Directory->Local Directory->Import Local
import-export-contac
Directory File
ts = 0
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
btnImportCSV = 0
(1 for SIP
VP-T49G/CP860/
Directory->Local Directory->
W56P IP phones)
btnExportCSV = 0
(1 for SIP
VP-T49G/CP860/
Directory->Local Directory->
W56P IP phones)
btnImportXML = 0
(1 for SIP
VP-T49G/CP860/
Directory->Local Directory->
W56P IP phones)
btnExportXML = 0
(1 for SIP
VP-T49G/CP860/
Directory->Local Directory->
W56P IP phones)
78
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Directory->Local Directory->
[ LocalPhoneBook
]
(not applicable to
W56P IP DECT
opt-contacts = 0
phones)
remote-phonebook-li
Directory->Remote Phone Book->
st = 1
(0 for SIP
VP-T49G/CP860/
W56P IP phones)
SRemoteNameEnable
[ Contacts-Remote
]
=1
(0 for SIP
VP-T49G/CP860/
Directory->Remote Phone
Book->Incoming/Outgoing Call Lookup
W56P IP phones)
SRemoteNameFlashTi
me = 1
(0 for SIP
VP-T49G/CP860/
Directory->Remote Phone Book->Update
Time Interval(Seconds)
W56P IP phones)
Directory->Phone Call Info->Call Panel
call-control = 0
[ PhoneCallInfo ]
(not applicable to
W56P IP DECT
phones)
dialed-list-title = 0
(only applicable to SIP
VP-T49G/CP860 IP
phones)
dialed-list-content =
Directory->Phone Call Info->
Directory->Phone Call Info->
Directory->Phone Call Info->Placed List
0
(only applicable to SIP
VP-T49G/CP860 IP
79
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
phones)
dialed-list = 0
Directory->Phone Call Info->
(not applicable to SIP
VP-T49G/CP860 IP
phones)
missed-list-title = 0
(only applicable to SIP
VP-T49G/CP860 IP
Directory->Phone Call Info->
phones)
missed-list-content =
0
Directory->Phone Call Info->Missed List
(only applicable to SIP
VP-T49G/CP860 IP
phones)
[ PhoneCallInfo ]
(not applicable to
W56P IP DECT
phones)
missed-list = 0
Directory->Phone Call Info->
(not applicable to SIP
VP-T49G/CP860 IP
phones)
received-list-title = 0
(only applicable to SIP
VP-T49G/CP860 IP
Directory->Phone Call Info->
phones)
received-list-content
=0
Directory->Phone Call Info->Received List
(only applicable to SIP
VP-T49G/CP860 IP
phones)
received-list = 0
Directory->Phone Call Info->
(not applicable to SIP
VP-T49G/CP860 IP
phones)
forwarded-list-title =
0
(only applicable to SIP
Directory->Phone Call Info->
VP-T49G/CP860 IP
80
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
phones)
forwarded-list-conten
t=0
[ PhoneCallInfo ]
(only applicable to SIP
(not applicable to
VP-T49G/CP860 IP
W56P IP DECT
phones)
Directory->Phone Call Info->Forwarded List
phones)
forwarded-list = 0
Directory->Phone Call Info->
(not applicable to SIP
VP-T49G/CP860 IP
phones)
enable-LDAP = 0
Directory->LDAP->Enable LDAP
LDAP-name-filter = 0
Directory->LDAP->LDAP Name Filter
LDAP-number-filter =
0
[ LDAP ]
(not applicable to
SIP-T19(P) E2 IP
phones)
Directory->LDAP->LDAP Number Filter
LDAP-TLS-Mode = 0
Directory->LDAP->LDAP TLS Mode
server-address = 0
Directory->LDAP->Server Address
port = 0
Directory->LDAP->Port
base = 0
Directory->LDAP->Base
user-name = 0
Directory->LDAP->Username
password = 0
Directory->LDAP->Password
maxhits = 0
Directory->LDAP->Max Hits (1~32000)
LDAP-name-attribute
s=0
Directory->LDAP->LDAP Name Attributes
LDAP-number-attribu
Directory->LDAP->LDAP Number
tes = 0
Attributes
LDAP-display-name =
0
Directory->LDAP->LDAP Display Name
protocol = 0
Directory->LDAP->Protocol
LDAP-lookup-for-inco
Directory->LDAP->LDAP Lookup For
ming-call = 0
Incoming Call
LDAP-lookup-for-call
Directory->LDAP-> LDAP Lookup For
out = 0
Callout
LDAP-sorting-results
Directory->LDAP->LDAP Sorting Results
81
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
=0
Receive_Priority = 1
(0 for SIP
VP-T49G/CP860 IP
Directory->Multicast IP->Paging Barge
phones)
PagePriorityActive = 1
(0 for SIP
Directory->Multicast IP->Paging Priority
VP-T49G/CP860 IP
Active
phones)
Directory->Multicast IP->
[ MulticastIP ]
(not applicable to
W56P IP DECT
phones)
MulticastIPConfig = 1
(0 for SIP
VP-T49G/CP860 IP
phones)
Directory->Multicast IP->Paging List
PagingList = 1
(0 for SIP
VP-T49G/CP860 IP
phones)
Directory->Setting->Directory
contacts-group = 0
(not applicable to
W56P/SIP VP-T49G IP
phones)
[ Contacts-Favorit
e]
super-search = 0
Directory->Setting->Search Source List In
Dialing
82
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
[ Contacts-Favorit
e]
Directory->Setting->Recent Call In Dialing
password = 0
trusted_cert = 2
[ Security ]
server_cert = 2
Security->Password (the whole page)
Security->Trusted Certificates (the whole
page)
Security->Server Certificates (the whole
page)
base-pin = 0
(only applicable to
W56P IP DECT
Security->Base PIN (the whole page)
phones)
Security->Password->
set-password = 0
[ Password ]
(only applicable to SIP
VP-T49G IP phones)
Security->Trusted Certificates->
trust-certs-records =
2
[ TrustCerts ]
btn-delete-certs = 2
Security->Trusted Certificates->
only-accept-trusted-c
Security->Trusted Certificates->Only
erts = 2
Accept Trusted Certificates
common-name-valida
Security->Trusted Certificates->Common
tion = 2
Name Validation
ca-certs = 2
Security->Trusted Certificates->CA
Certificates
83
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Security->Trusted Certificates->Import
[ TrustCerts ]
upload-trust-certs = 2
server-certs-records =
Trusted Certificates
Security->Server Certificates
2
server-certs-device-ce
[ ServerCerts ]
rt = 2
Security->Server Certificates->Device
Certificates
Security->Server Certificates->Import
server-certs-upload =
Server Certificates
2
[ BasePin ]
(only applicable to
W56P IP DECT
Base-unit-pin = 0
Security->Base PIN->Base Unit PIN
phones)
custom-factory-confi
g=2
Hidden->Custom Factory Config
DND-Active = 2
Hidden->DND Active
Forward-Active = 2
Hidden->Forward Active
Broadsoft-Active = 2
(1 for SIP
VP-T49G/CP860/
Hidden->Broadsoft Active
W56P IP phones)
[ HiddenSetting ]
Redirect-Active = 2
(1 for SIP
VP-T49G/CP860/
Hidden->Redirect Active
W56P IP phones)
XSI-Active = 2
(not applicable to SIP
VP-T49G/CP860/
Hidden->XSI Active
W56P IP phones)
UC-Active = 2
Hidden->UC Active
84
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
(1 for SIP VP-T49G IP
phones; only
applicable to SIP
VP-T49G/SIP-T48G/
T48S/T46G/T46S/
T29G IP phones)
remote_pcap_switch
=2
Hidden->Remote Pcap
(only applicable to
Hidden->Remote Pcap Port
SIP-T48G/T48S/T46G/
Hidden->Remote Pcap Password
T46S/T29G IP phones)
remote_pcap = 2
(only applicable to
[ HiddenSetting ]
SIP-T48G/T48S/T46G/
Hidden->Remote Pcap
T46S/T29G IP phones)
remote_pcap_port = 2
(only applicable to
SIP-T48G/T48S/T46G/
Hidden->Remote Pcap Port
T46S/T29G IP phones)
remote_pcap_passwor
d=2
(only applicable to
Hidden->Remote Pcap Password
SIP-T48G/T48S/T46G/
T46S/T29G IP phones)
pushxml = 2
(not applicable to
W56P IP DECT
Hidden->PushXML Test
phones)
The following table lists configuration items in the WebItemsLevel.cfg file for configurations
only integrated with BroadSoft UC-One firmware version on the web user interface.
Section Header
[ General-Informat
Parameters and
Configuration Items on the Web User
Default Value
Interface
EnableAutoFavorite = 0
Features->General Information->Enable
85
Configuration Guide for User Access Level
Section Header
ion ]
Parameters and
Configuration Items on the Web User
Default Value
Interface
(only applicable to SIP
Auto Favorite
VP-T49G/SIP-T48G/
T48S/T46G/T46S/T29G
IP phones)
[ Contacts ]
(only applicable to
contacts-broadsoft = 0
SIP
VP-T49G/CP860/
Directory->Network Directory (the whole
page)
W56P IP phones)
Directory->Network Directory->Network
Directory
Directory->Network Directory->Custom
Directory
Directory->Network Directory->Call Log
Directotries = 0
[ Contacts-Broads
oft ]
(only applicable to
SIP
VP-T49G/CP860/
W56P IP phones)
Directory->Network Directory->XSI
XSI = 0
[ Apps ]
(not applicable to
broadsoft-XSI = 1
Applications->Broadsoft XSI (the whole
page)
SIP
VP-T49G/CP860/
W56P IP phones)
broadsoft-XMPP = 1
XSI = 1
Applications->Broadsoft XMPP (the whole
page)
Applications->Broadsoft XSI->XSI Account
86
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Web User
Default Value
Interface
Applications->Broadsoft XSI->Network
Directory
Applications->Broadsoft XSI->Custom
Directory
[ Broadsoft ]
Directotries = 1
(not applicable to
SIP
VP-T49G/CP860/
W56P IP phones)
CallLog = 1
Applications->Broadsoft XSI->Call Log
Applications->Broadsoft XMPP->XMPP
Account
XMPP-accout = 1
XMPP-userame = 1
XMPP-password = 1
Applications->Broadsoft XMPP->XMPP
UserName
Applications->Broadsoft XMPP->XMPP
Password
87
Configuration Guide for User Access Level
Configuration Parameters of Phone User Interface
The following table lists configuration items in the WebItemsLevel.cfg file with associated
configurations on the phone user interface of the SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23P/T23G
/T21(P) E2/T19(P) E2/CP860 IP phones:
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
status_list = 0
Menu->Status
SIP VP-T49G:
Menu->Status->General->IPv4
Status_IP = 0
SIP-T48G/T48S:
(11 for SIP
Menu->Status->General->IPv4 IP
VP-T49G/CP860/
SIP-T46G/T46S/T42G/T42S/T41P/T41S/
W56P IP phones)
T40P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Status->IPv4 (or IPv4 Address)
SIP VP-T49G:
Menu->Status->General->IPv6
Status_IPv6 = 0
SIP-T48G/T48S:
(11 for SIP
Menu->Status->General->IPv6 IP
VP-T49G/CP860/
SIP-T46G/T46S/T42G/T42S/T41P/T41S/
W56P IP phones)
T40P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Status->IPv6 (or IPv6 Address)
SIP VP-T49G/SIP-T48G/T48S:
[ GUI ]
Status_MAC = 0
Menu->Status->General->MAC Address
(21 for SIP
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
VP-T49G/CP860/
P/T29G/T27P/T27G/T23P/T23G/T21(P)
W56P IP phones)
E2/T19(P) E2/CP860:
Menu->Status->MAC Address
SIP VP-T49G/SIP-T48G/T48S:
Status_HW = 0
Menu->Status->Phone->Hardware
(01 for SIP
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
VP-T49G/CP860/
P/T29G/T27P/T27G/T23P/T23G/T21(P)
W56P IP phones)
E2/T19(P) E2/CP860:
Menu->Status->More->Phone->Hardware
88
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Status_More = 0
(01 for CP860/W56P IP
phones; not applicable
to SIP
Menu->Status->More
VP-T49G/SIP-T48G/
T48S IP phones)
SIP VP-T49G/SIP-T48G/T48S:
Menu->Status->Network
network = 0
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Status->More->Network
SIP VP-T49G/SIP-T48G/T48S:
Menu->Status->Phone
Status_More_Phone = 0
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Status->More->Phone
[ GUI ]
SIP VP-T49G/SIP-T48G/T48S:
Menu->Status->Accounts
Status_More_Account =
0
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Status->More->Accounts (or
Account)
SIP VP-T49G/SIP-T48G/T48S/T46G/T46S/
Status_More_RTP = 0
T29G:
(02 for SIP
Menu->Status->RTP Status
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Status->More->RTP
status_general= 0
(02 for SIP VP-T49G IP
phones; only applicable
Menu->Status->General
to SIP
VP-T49G/SIP-T48G/
89
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
T48S IP phones)
features = 0
(02 for SIP
VP-T49G/CP860/
Menu->Features
W56P IP phones)
callcontrol_forward = 1
(11 for SIP
VP-T49G/CP860/
Menu->Features->Call Forward
W56P IP phones)
always-forward = 0
(1 for SIP
Menu->Features->Call Forward->Always
VP-T49G/CP860/
Forward
W56P IP phones)
busy-forward = 0
[ GUI ]
(1 for SIP
Menu->Features->Call Forward->Busy
VP-T49G/CP860/
Forward
W56P IP phones)
NoAnswer-forward = 0
(1 for SIP
Menu->Features->Call Forward->No
VP-T49G/CP860/
Answer Forward
W56P IP phones)
call_waiting = 0
(1 for SIP
VP-T49G/CP860/
Menu->Features->Call Waiting
W56P IP phones)
auto-Answer= 0
(1 for SIP
VP-T49G/CP860/
Menu->Features->Auto Answer
W56P IP phones)
DSSKey = 0
(1 for SIP VP-T49G IP
phones; not applicable
to SIP-T19(P)
Menu->Features->DSS Keys
E2/CP860/W56P IP
phones)
90
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
SIP VP-T49G/SIP-T48G/T48S:
Menu->Features->General->Key As Send
key_as_send= 0
SIP-T46G/T46S/T29G:
(12 for SIP
Menu->Features->Others->General->Key
VP-T49G/CP860/
As Send
W56P IP phones)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Features->Key As Send
SIP VP-T49G/SIP-T48G/T48S:
Menu->Features->Hot Line->Hotline
Number
hotline-number = 0
(1 for SIP
VP-T49G/CP860/
[ GUI ]
W56P IP phones)
SIP-T46G/T46S/T29G:
Menu->Features->Others->Hot
Line->Hotline Number
SIP-T42G/T42S/T41P/T41S/T40P/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P)
E2/CP860:
Menu->Features->Hot Line->Hotine
Number
Features_Anonymous =
0
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Anonymous
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Features->Anonymous Call
Features_Diagnostics =
0
(not applicable to SIP
Menu->Features->Diagnostics
VP-T49G/CP860/W56P
IP phones)
Diagnostics_Network =
0
(not applicable to SIP
Menu->Features->Diagnostics->Network
VP-T49G/CP860/W56P
IP phones)
Diagnostics_Ping = 0
Menu->Features->Diagnostics->Network-
91
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
(not applicable to SIP
>Ping
VP-T49G/CP860/W56P
IP phones)
Diagnostics_TraceRoute
=0
(not applicable to SIP
VP-T49G/CP860/W56P
Menu->Features->Diagnostics->Network>Trace Route
IP phones)
SIP
Features_AutoRD = 0
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T42G/T42S/T41P/
T41S/T40P/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Features->Auto Redial
SIP-T46G/T46S/T29G:
Menu->Features->Others->Auto Redial
[ GUI ]
intercom = 0
(1 for SIP
VP-T49G/CP860/
Menu->Features->Intercom
W56P IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T42G/T42S/T41P/
call_completion = 0
(1 for SIP
T41S/T40P/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
VP-T49G/CP860/
Menu->Features->Call Completion
W56P IP phones)
SIP-T46G/T46S/T29G:
Menu->Features->Others->Call
Completion
SIP VP-T49G/SIP-T48G/T48S:
Menu->Features->General->History
Record
SIP-T46G/T46S/T29G:
history_save= 2
Menu->Features->Others->General->Histo
ry Record
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Features->History Setting
92
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
SIP
multpaginglist = 2
(10 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T42G/T42S/T41P/
T41S/T40P/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Features->Paging List
SIP-T46G/T46S/T29G:
Menu->Features->Others->Paging List
Main_Settings=0
(not applicable to SIP
VP-T49G/SIP-T48G/
Menu->Settings
T48S/T46G/T46S/T29G
IP phones)
SIP VP-T49G/SIP-T48G/T48S:
Menu->Basic->Time &
Date->General->Time Zone
SIP-T46G/T46S/T29G:
[ GUI ]
Menu->Basic->Time &
time_zone = 0
Date->General->SNTP Settings>Time Zone
SIP-T42G/T42S/T41P/T41S/T40P/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P)
E2/CP860:
Menu->Settings->Basic Settings->Time &
Date->SNTP Settings->Time Zone
SIP VP-T49G/SIP-T48G/T48S:
Menu->Basic->Time &
Date->General->Type (Manual Settings)
SIP-T46G/T46S/T29G:
Menu->Basic->Time &
Basic_Time_Manual = 0
Date->General->Manual Settings
SIP-T42G/T42S/T41P/T41S/T40P/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P)
E2/CP860:
Menu->Settings->Basic Settings->Time &
Date->Manual Settings
display = 0
SIP
(10 for SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
93
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
VP-T49G/CP860/
Menu->Basic->Display
W56P IP phones)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P)
E2/CP860:
Menu->Settings->Basic Settings->Display
SIP
sound = 0
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Sound
SIP-T42G/T42S/T41P/T41S/T40P/T27P/
T27G/T23P/T23G/T21(P) E2/T19(P)
E2/CP860:
Menu->Settings->Basic Settings->Sound
SIP
key_tone = 0
(1 for SIP
VP-T49G/CP860/
W56P IP phones)
[ GUI ]
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Sound->Key Tone
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Basic
Settings->Sound->Key Tone
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
ring_type_setting = 0
Menu->Basic->Sound->Ring Tones
(1 for SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
W56P IP phones)
Menu->Settings->Basic
Settings->Sound->Ring Tones
SIP-T48G/T48S/T46G/T46S/T29G:
blf_ring_setting = 0
Menu->Basic->Sound->BLF Ring Type
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P/
G/T23P/T23G/T21(P) E2:
T19(P) E2 IP phones)
Menu->Settings->Basic
Settings->Sound->BLF Ring Type
unlock_pin = 0
(2 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Change PIN
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
94
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Menu->Settings->Basic Settings->Change
PIN
SIP-T48G/T48S/T46G/T46S/T29G:
check_key_guard_lock =
0
(not applicable to SIP
VP-T49G/CP860/W56P IP
phones)
Menu->Basic->Phone Lock
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Basic Settings->Phone
Lock
bluetooth = 0
(1 for SIP VP-T49G IP
phones; only applicable
to
Menu->Basic->Bluetooth
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
phones)
wifi = 0
(2 for SIP VP-T49G IP
phones; only applicable
[ GUI ]
to SIP
Menu->Basic->Wi-Fi
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
phones)
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Label
account_label = 0
SIP-T46G/T46S/T29G:
(02 for SIP
Menu->Advanced->Accounts->Account
VP-T49G/CP860/
X->Label
W56P IP phones)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->Label
display_name = 0
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Display Name
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
95
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
X->Display Name
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->Display
Name
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Register Name
register_name = 01
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
X->Register Name
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->Register
Name
[ GUI ]
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->User Name
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
user_name = 01
X->User Name
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->User
Name
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Password
SIP-T46G/T46S/T29G:
account_password = 01
Menu->Advanced->Accounts->Account
X->Password
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
96
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Settings->Accounts->Account
X->Password
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->SIP Server1/2
sip_server = 2
(01 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
X->SIP Server1/2
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->SIP
Server1/2
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Outbound Status
[ GUI ]
enabled-outbound-pro
SIP-T46G/T46S/T29G:
xy-server = 2
Menu->Advanced->Accounts->Account
(01 for SIP
X->Outbound Status
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account
X->Outbound Status
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Outbound Proxy1/2
outbound-proxy-server
SIP-T46G/T46S/T29G:
=2
Menu->Advanced->Accounts->Account
(01 for SIP
X->Outbound Proxy1/2
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account
X->Outbound Proxy1/2
STUN_server = 2
SIP VP-T49G/SIP-T48G/T48S:
(02 for SIP
Menu->Advanced->Account->Account
97
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
VP-T49G/CP860 IP
X->NAT Status
phones)
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
X->NAT Status
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->NAT
Status
proxy-fallback-interval
= 01
Menu->Advanced->Account->Account
(only applicable to SIP
X->Fallback Interval
VP-T49G IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network
Adv_Network =0
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
[ GUI ]
Menu->Settings->Advanced
Settings->Network
SIP
wan_port_title = 0
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->WAN Port
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->WAN Port
SIP
VLAN-items = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->VLAN
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->VLAN
wanport = 0
SIP
(02 for SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
98
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
VP-T49G/CP860/
Menu->Advanced->Network->VLAN
W56P IP phones)
->WAN Port
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->VLAN->WAN Port
SIP
pcport = 2
(02 for SIP
VP-T49G/W56P IP
phones; not applicable
to CP860 IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->VLAN->PC
Port
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced
Settings->Network->VLAN->PC Port
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
dhcpvlan = 2
Menu->Advanced->Network->VLAN->DH
(02 for SIP
CP VLAN
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
[ GUI ]
Settings->Network->VLAN->DHCP VLAN
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
web-server = 2
Menu->Advanced->Network->Webserver
(02 for SIP
Type (Web Server)
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->Web Server
SIP
8021x = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->802.1x
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->802.1x
99
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
open-VPN = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones; not
applicable to SIP-T19(P)
E2 IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->VPN
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->VPN
SIP
open-lldp = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->LLDP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->LLDP
SIP
network_cdp = 2
(02 for SIP
VP-T49G/CP860/
[ GUI ]
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->CDP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->CDP
SIP
network_nat = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Network->NAT
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Network->NAT
softkey Label = 0
(02 for CP860/W56P IP
phones; not applicable
to SIP
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Softkey Label
phones)
keyboard_lock = 02
(only applicable to SIP
SIP VP-T49G:
100
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
VP-T49G/CP860 IP
Menu->Advanced->Phone Lock
phones)
CP860:
Menu->Settings->Advanced
Settings->Phone Lock
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Reboot
Adv_Reboot = 0
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP-T46G/T46S/T29G:
Menu->Advanced->Reset&Reboot->Rebo
ot
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Reboot
Adv_ResetToFac = 2
SIP VP-T49G:
Menu->Advanced->Reset to Factory
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Reset Config->Reset
to factory
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
[ GUI ]
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced
Settings->Reset Config->Reset to factory
CP860:
Menu->Settings->Advanced
Settings->Reset to factory settings
SIP-T48G/T48S/T46G/T46S/T29G:
Adv_ResetConfig = 0
Menu->Advanced->Reset Config
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P
G/T23P/T23G/T21(P) E2/T19(P) E2:
IP phones)
Menu->Settings->Advanced
Settings->Reset Config
ResetLocalConfig = 0
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Reset Config->Reset
local settings (only appear when the
parameter
“static.auto_provision.custom.protect” is set
101
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
to 1.)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced
Settings->Reset Config->Reset local
settings (only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Reset Config->Reset
non-static settings (only appear when the
parameter
ResetNonStaticConfig =
“static.auto_provision.custom.protect” is set
0
to 1.)
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P
G/T23P/T23G/T21(P) E2/T19(P) E2:
IP phones)
Menu->Settings->Advanced
Settings->Reset Config->Reset non-static
settings (only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
[ GUI ]
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Reset Config->Reset
static settings (only appear when the
parameter
ResetStaticConfig = 2
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
“static.auto_provision.custom.protect” is set
to 1.)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Reset
Config->Advanced Settings->Reset static
settings (only appear when the parameter
“static.auto_provision.custom.protect” is set
to 1.)
ResetUserDataUserCfg
Menu->Advanced->Reset Config->Reset
=0
userdata & local config (only appear when
(not applicable to SIP
the parameter
VP-T49G/CP860/
“static.auto_provision.custom.protect” is set
to 1.)
102
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
W56P IP phones)
SIP VP-T49G:
Menu->Advanced->Reset Config->Reset
Local Settings (only appear when the
reset_default = 0
parameter “auto_provision.custom.protect”
(only applicable to SIP
is set to 1.)
VP-T49G/CP860 IP
CP860:
phones)
Menu->Settings->Advanced
Settings->Reset Local Settings (only appear
when the parameter
“auto_provision.custom.protect” is set to 1.)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Set Password (Change
password = 0
Password)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced Settings->Set
Password (Change Password)
[ GUI ]
Adv_AES = 02
(only applicable to SIP
VP-T49G/CP860 IP
phones)
SIP VP-T49G:
Menu->Advanced->Set AES Key
CP860:
Menu->Settings->Advanced Settings->Set
AES Key
SIP
autoprovision = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->Auto Provision
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Auto Provision
international-forward =
2
(02 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Advanced->FWD International
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
103
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Settings->FWD International
SMS= 0
(12 for SIP
VP-T49G/CP860/
Menu->Message
W56P IP phones)
MSG_Voice = 0
(1 for SIP
VP-T49G/CP860/
Menu->Message->Voice Mail
W56P IP phones)
viewvoicemail = 0
(1 for SIP
Menu->Message->Voice Mail->View Voice
VP-T49G/CP860/
Mail
W56P IP phones)
setvoicemail = 0
(1 for SIP
Menu->Message->Voice Mail->Set Voice
VP-T49G/CP860/
Mail Code
W56P IP phones)
[ GUI ]
usermodeentry = 0
Menu->User Mode
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
NAT_traversal = 2
(02 for SIP
VP-T49G/CP860/
W56P IP phones; not
applicable to SIP-T19(P)
E2 IP phones)
X->NAT Status
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
X->NAT Status
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X->NAT
Status
SIP-T48G/T48S/T46G/T46S/T29G:
contrast_ctrl = 0
Menu->Basic->Display->Contrast Setting
(not applicable to SIP
CP860/SIP-T40P/T27P/T27G/T23P/T23G/T2
VP-T49G/SIP-
1(P) E2/T19(P) E2:
T42G/T42S/T41P/T41S)
Menu->Settings->Basic
Settings->Display->Contrast
104
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
local_call_log_list = 0
(01 for SIP
VP-T49G/CP860/
Menu->Directory->Local Directory
W56P IP phones)
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account
Adv_Account = 0
SIP-T46G/T46S/T29G:
(2 for SIP
Menu->Advanced->Accounts
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced
Settings->Accounts
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Language
Basic_LANG = 0
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Basic
[ GUI ]
Settings->Language
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Display->Backlight
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
Basic_Setting_BackLight
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
=0
Menu->Settings->Basic
Settings->Display->Backlight
CP860:
Menu->Settings->Basic
Settings->Display->Backlight Settings
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Basic->Time & Date->Time & Date
Basic_Time_Format = 0
Format
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Basic Settings->Time &
105
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Date->Time & Date Format
SIP VP-T49G/SIP-T48G/T48S:
Menu->Basic->Time&
Date->General->Type (SNTP Settings)
SIP-T46G/T46S/T29G:
Basic_Time_SNTP = 0
Menu->Basic->Time &
Date->General->SNTP Settings
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Basic Settings->Time &
Date->SNTP Settings
MSG_Text = 0
Menu->Message->Text Message
Main_Contacts = 0
Menu->Directory
SMS_Draftbox = 0
SMS_Inbox = 0
[ GUI ]
SMS_NEW = 0
SMS_Outbox = 0
SMS_Sentbox = 0
Menu->Message->Text Message
->Draftbox
Menu->Message->Text Message
->Inbox
Menu->Message->Text Message
->New Message
Menu->Message->Text Message
->Outbox
Menu->Message->Text Message->
Sentbox
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Set_Adv = 0
Menu->Advanced
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Advanced Settings
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Set_Basic = 0
Menu->Basic
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
106
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Menu->Settings->Basic Settings
blacklist_list = 0
Menu->Directory->Blacklist
call_info = 0
Menu->History
usb_record= 0
(only applicable to
SIP-T48G/T48S/T46G/
Menu->USB
T46S/T29G IP phones)
browse_usb_record= 0
(only applicable to
SIP-T48G/T48S/T46G/
Menu->USB->Browse Audio
T46S/T29G IP phones)
browse_usb_storage= 0
(only applicable to
SIP-T48G/T48S/T46G/
Menu->USB->Storage Space
T46S/T29G IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
[ GUI ]
Menu->Basic->Time & Date->DHCP Time
dhcptimezone = 0
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Settings->Basic Settings->Time &
Date->DHCP Time
SIP VP-T49G/SIP-T48G/T48S:
Menu->Advanced->Account->Account
X->Activation
SIP-T46G/T46S/T29G:
Menu->Advanced->Accounts->Account
line_active = 0
X->Activation
(2 for SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
W56P IP phones)
Menu->Settings->Advanced
Settings->Accounts->Account X
->Activation
CP860:
Menu->Settings->Advanced
Settings->Accounts->Account X ->Account
107
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
Status
SIP VP-T49G/SIP-T48G/T48S:
Menu->Directory->All Contacts
local_contact_list = 0
SIP-T46G/T46S/T42G/T42S/T41P/T41S/T40
P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2/CP860:
Menu->Directory->Local Directory
remote_contact_list = 0
Menu->Directory->Remote Phone book
status = 0
Menu->Status
dnd = 0
Menu->Features->DND
advanced_call_feature_
default_account =0
(2 for SIP VP-T49G IP
phones; only applicable
to SIP
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
SIP VP-T49G/SIP-T48G/T48S:
Menu->Features->Default Account
SIP-T46G/T46S/T29G:
Menu->Features->Others->Default
Account
phones)
advanced_call_feature_
general = 0
[ GUI ]
(1 for SIP VP-T49G IP
SIP VP-T49G/SIP-T48G/T48S:
phones; only applicable
Menu->Features->General
to SIP
SIP-T46G/T46S/T29G:
VP-T49G/SIP-T48G/T48
Menu->Features->Others->General
S/T46G/T46S/T29G IP
phones)
advanced_call_feature_li
st = 0
(1 for SIP VP-T49G IP
phones; only applicable
to SIP
Menu->Features
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
phones)
date_and_time_general
=0
Menu->Basic->Time &Date->General
(only applicable to SIP
108
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
phones)
reset_and_reboot_list =
0
(only applicable to
Menu->Advanced->Reset&Reboot
SIP-T46G/T46S/T29G IP
phones)
display_wallpaper = 0
(1 for SIP VP-T49G IP
phones; only applicable
to SIP
Menu->Basic->Display->Wallpaper
VP-T49G/SIP-T48G/T48
S/T46G/T46S/T29G IP
phones)
display_dsskey_wallpap
er = 0
(only applicable to
SIP-T48G/T48S IP
Menu->Basic->Display->DSSKey
Wallpaper
phones)
[ GUI ]
screensaver = 0
(only applicable to
SIP-T48G/T48S/T46G/T
Menu->Basic->Display->Screensaver
46S/T29G IP phones)
camera_setting_interfac
e = 00
(only applicable to SIP
Menu->Basic->Camera Setting
VP-T49G IP phones)
usb_interface = 00
(only applicable to SIP
Menu->USB
VP-T49G IP phones)
usb_browse_audio = 00
(only applicable to SIP
Menu->USB->Browse Audio
VP-T49G IP phones)
usb_browse_video = 00
(only applicable to SIP
Menu->USB->Browse Video
VP-T49G IP phones)
109
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
usb_browse_photo = 00
(only applicable to SIP
Menu->USB->Browse Photo
VP-T49G IP phones)
usb_storage_property =
00
(only applicable to SIP
Menu->USB->Storage Space
VP-T49G IP phones)
hdmi = 00
[ GUI ]
(only applicable to SIP
Menu->Basic->HDMI
VP-T49G IP phones)
video_setting_interface
= 00
(only applicable to SIP
Menu->Basic->Video Setting
VP-T49G IP phones)
usb-record = 0
(only applicable to
Menu->USB Record
CP860 IP phones)
browserecordfiles = 0
(only applicable to
Menu->USB Record->Playback Recording
CP860 IP phones)
browseusbstorge = 0
(only applicable to
CP860 IP phones)
Menu->USB Record->Storage Media
Properties
110
Configuration Guide for User Access Level
The following table lists configuration items in the WebItemsLevel.cfg file for configurations
only integrated with BroadSoft UC-One firmware version on the phone user interface of the SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23P/T23G
/T21(P) E2/T19(P) E2/CP860 IP phones.
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
broadsoft_contact_list =
1
(0 for SIP
Menu->Directory->Network Directory
VP-T49G/CP860/
W56P IP phones)
broadsoft_calllog_list =
0
Menu->History->Network CallLog
SIP
CallControl = 1
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
(0 for SIP
Menu->Features->Call Control
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control
[ GUI ]
callcontrol_anywhere =
1
(11 for SIP
VP-T49G/CP860/
W56P IP phones)
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->Anywhere
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Anywhere
SIP
callcontrol_remoteoffic
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
e=1
Menu->Features->Call Control->Remote
(11 for SIP
Office
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Remote Office
callcontrol_dnd= 1
SIP
(11 for SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
VP-T49G/CP860/
Menu->Features->Call Control->Do not
W56P IP phones)
Disturb
111
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Do Not Disturb
SIP
callcontrol_sinultaneous
ring = 1
(11 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call
Control->Simultaneous Ring Personal
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Simultaneous Ring
Personal
callcontrol_mobility = 1
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
callcontrol_group_night
[ GUI ]
_forward = 1
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
callcontrol_callwaiting =
1
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
callcontrol_forward_sele
ctive = 1
(not applicable to SIP
VP-T49G/CP860/W56P
IP phones)
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->Mobility
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Call Control->Mobility
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->Group
Night Forward
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Call Control->Group Night Forward
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->Call
Waiting
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Call Control->Call Waiting
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->Call
Forward
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Call Control->Call Forward
callcontrol_executive =
SIP-T48G/T48S/T46G/T46S/T29G:
1
Menu->Features->Call Control->Executive
112
Configuration Guide for User Access Level
Parameters and
Configuration Items on the Phone User
Default Value
Interface
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P
G/T23P/T23G/T21(P) E2/T19(P) E2:
IP phones)
Menu->Call Control->Executive
Section Header
SIP-T48G/T48S/T46G/T46S/T29G:
callcontrol_securityclass
Menu->Features->Call Control->Security
ification = 1
Classification
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P
G/T23P/T23G/T21(P) E2/T19(P) E2:
IP phones)
Menu->Call Control->Security
Classification
callcontrol_executive_as
sistant = 1
(not applicable to SIP
VP-T49G/CP860/W56P
[ GUI ]
IP phones)
SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call
Control->Executive-Assistant
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Call Control->Executive-Assistant
SIP
callcontrol_hidenumber
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
=1
Menu->Features->Call Control->Hide
(11 for SIP
Number
VP-T49G/CP860/
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
W56P IP phones)
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Hide Number
SIP
callcontrol_anonymousr
ejection = 1
(11 for SIP
VP-T49G/CP860/
W56P IP phones)
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call
Control->Anonymous Rejection
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Anonymous
Rejection
callcontrol_initialacdstat
SIP
e=1
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
(11 for SIP
Menu->Features->Call Control->Initial
VP-T49G/CP860/
ACD State
W56P IP phones)
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
113
Configuration Guide for User Access Level
Section Header
Parameters and
Configuration Items on the Phone User
Default Value
Interface
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->Initial ACD State
callcontrol_setacdstate
=1
(11 for SIP
VP-T49G/CP860/
W56P IP phones)
[ GUI ]
SIP
VP-T49G/SIP-T48G/T48S/T46G/T46S/T29G:
Menu->Features->Call Control->ACD State
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
Menu->Call Control->ACD State
SIP-T48G/T48S/T46G/T46S/T29G:
callcontrol_securityclass
Menu->Features->Call Control->Security
ification = 0
Classification
(not applicable to SIP
SIP-T42G/T42S/T41P/T41S/T40P/T27P/T27
VP-T49G/CP860/W56P
G/T23P/T23G/T21(P) E2/T19(P) E2/CP860:
IP phones)
Menu->Call Control->Security
Classification
114
Configuration Guide for User Access Level
Configuration Parameters of Handset User Interface
The following table lists configuration items in the WebItemsLevel.cfg file with associated
configurations on the handset user interface of the W56P IP DECT phones:
Section
Parameters and Default
Configuration Items on the Handset
Header
Value
User Interface
Menu_Status = 0
OK->Status
Base = 0
OK->Status->Base
Handset = 0
OK->Status->Handset
LineStatus = 0
OK->Status->Line Status
Menu_Intercom = 0
OK->Intercom
Intercom_HSXS = 0
OK->Intercom->Handset X
Intercom_ALLHS = 0
OK->Intercom->All HS
Menu_VoiceMail = 0
OK->Voice Mail
Play_Message = 0
OK->Voice Mail->Play Message
Set_Voice_Mail = 0
OK->Voice Mail->Set Voice Mail
Set_Key_1 = 0
OK->Voice Mail->Set Key 1
Menu_CallFeatures = 0
OK->Call Features
CallForward = 0
OK->Call Features->Call Forware
AlwaysForward= 0
[ GUI ]
BusyForward= 0
NoAnswerForward= 0
OK->Call
Features->LineX->Always(Disable/Enable)
OK->Call
Features->LineX->Busy(Disable/Enable)
OK-> Call Features->LineX->No
Answer(Disable/Enable)
DND= 0
OK->Call Features->Do Not Disturb
CallWaiting= 0
OK->Call Features->Call Waiting
AnonymousRejection = 0
OK->Call Features->Anon.Call Rejection
AnonymousCall = 0
OK->Call Features->Anonymous Call
Menu_Directory = 0
OK->Directory
Local_Contact_List= 0
OK->Directory->Local Directory
Remote_Contact_List= 0
OK->Directory->Remote Dir
115
Configuration Guide for User Access Level
Section
Parameters and Default
Configuration Items on the Handset
Header
Value
User Interface
Broadsoft_Contact_List= 0
OK->Directory->Network Directory
LDAP_Contact_List= 0
OK->Directory->LDAP
Menu_Settings = 0
OK->Settings
DateTime = 0
OK->Settings->Date & Time
Audio = 0
OK->Settings->Audio
Advisory_Tones = 0
OK->Settings->Audio->Advisory Tones
Ring_Tones = 0
OK->Settings->Audio->Ring Tones
Volume = 0
Melodies = 0
[ GUI ]
OK->Settings->Audio->Ring
Tones->Volume
OK->Settings->Audio->Ring
Tones->Melodies
Display = 0
OK->Settings->Display
Screen_Saver = 0
OK->Settings->Display->Screen Saver
Wallpaper = 0
OK->Settings->Display->Wallpaper
Display_Backlight = 0
OK->Settings->Display->Display
Backlight
Keypad_Light = 0
OK->Settings->Display->Keypad Light
Time_Formate = 0
OK->Settings->Display->Time Format
Date_Formate = 0
OK->Settings->Display->Date Format
Input_Method = 0
OK->Settings->Display->Input Method
Shortcut = 0
OK->Settings->Shortcut
Soft_Left = 0
OK->Settings->Shortcut->History
Soft_Right = 0
OK->Settings->Shortcut->Line Status
Up = 0
OK->Settings->Shortcut->Intercom
Down = 0
OK->Settings->Shortcut->Directory
Left = 0
OK->Settings->Shortcut->Volume-
Right = 0
OK->Settings->Shortcut->Volume+
Language =0
OK->Settings->Language
Registration = 0
OK->Settings->Registration
Register_Handset = 0
OK->Settings->Registration->Register
116
Configuration Guide for User Access Level
Section
Parameters and Default
Configuration Items on the Handset
Header
Value
User Interface
Handset
De_reg_Handset = 0
Handset
Select_Base = 0
OK->Settings->Registration->Select Base
Telephony = 0
OK->Settings->Telephony
Auto_Answer = 0
OK->Settings->Telephony->Auto Answer
Auto_Intercom = 0
Default_Line = 0
Incoming_Lines = 02
Speed_Dial = 0
Blacklist = 0
SystemSettings= 0
[ GUI ]
OK->Settings->Registration->De-reg.
Network = 0
Handset_Reset = 0
Change_Base_PIN = 02
Base_Reset_Local_Cfg = 02
Base_Restart = 02
Auto_Provision = 02
RPS = 02
Eco_Mode_Plus = 02
Eco_Mode = 0
Repeater_Mode = 02
OK->Settings->Telephony->Auto
Intercom
OK->Settings->Telephony->Default Line
OK->Settings->Telephony->Incoming
Lines
OK->Settings->Telephony->Speed Dial
OK->Settings->Telephony->Caller
Blacklist
OK->Settings->System Settings
OK->Settings->System
Settings->Network
OK->Settings->System
Settings->Handset Reset
OK->Settings->System Settings->Change
Base PIN
OK->Settings->System Settings->Base
Reset
OK->Settings->System Settings->Base
Restart
OK->Settings->System Settings->Auto
Provision
OK->Settings->System Settings->RPS
OK->Settings->System Settings->Eco
Mode+
OK->Settings->System Settings->Eco
Mode
OK->Settings->System
117
Configuration Guide for User Access Level
Section
Parameters and Default
Configuration Items on the Handset
Header
Value
User Interface
Settings->Repeater Mode
HandsetName=
[ GUI ]
0
OK->Settings->Handset Name
UpgradeFirmware= 2
OK->Settings->Upgrade Firmware
Menu_History = 0
OK->History
All_Calls= 0
OK->History->All Calls
Missed_Calls= 0
OK->History->Outgoing Calls
Outgoing_Calls= 0
OK->History->Missed Calls
Accepted_Calls= 0
OK->History->Accepted Calls
Menu_Usermode = 0
OK->User Mode
118
Appendix-B
Sample Configuration Files
SIP VP-T49G IP Phones
The default configuration item settings in factory WebItemsLevel.cfg for SIP VP-T49G IP phones
running firmware version 51.80.0.108 or later are:
[ Status-Menu ]
Status-Basic = 0
Status-RTP = 0
Status-TalkStats = 0
[ Status ]
version = 0
network = 0
IPv4 = 0
IPv6 = 0
NetworkCommon = 0
AccountStatus = 0
Ext = 0
[ RTP-Status ]
rtcp-status = 11
[ Talk-Stats ]
talk-stats = 0
[ Account ]
account-register = 0
account-basic = 0
account-codec = 0
account-adv = 0
account-direct=0
[ Account-Register ]
switch-account = 0
account_status = 0
line_active = 0
account_label = 0
display_name = 0
register_name = 01
user_name = 01
119
Configuration Guide for User Access Level
account_password = 2
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
transport-item = 2
backup-outbound-proxy-server = 01
NAT_traversal = 2
sip_server = 2
proxy-fallback-interval = 01
[ Account-Basic ]
switch-account = 0
proxy_require = 0
send_anonymous = 1
anonymous_call_enabled = 0
anonymous_call_OnCode = 1
anonymous_call_OffCode = 1
anonymous_rejection_enabled = 0
send_anonymous_rejection_code = 0
anonymous_rejection_OnCode = 1
anonymous_rejection_OffCode = 1
misscall-log = 0
auto-answer = 0
ring-type = 0
[ Account-Codec ]
switch-account = 0
codecs-group = 0
[ Account-Adv ]
switch-account = 0
UDP_keep-alive = 2
local-SIP-port = 2
rport = 2
sip-session-timer = 2
subscribe-period = 2
DTMF_items = 2
reliable_retransmission = 2
MWI-items = 2
voice_mail = 0
voice_mail_display = 2
caller-ID-header =2
use-session-timer = 2
session-timer = 2
120
Configuration Guide for User Access Level
session-refresher = 2
user-equal-phone = 2
voice-encryption = 2
ptime-item = 2
share-line = 2
Call-Pull-Feature-Access-Code = 2
dialog-info-call-pickup = 2
BLF-list-URI = 2
BlfListCode = 2
BLFListBargeInCode = 2
BLF-List-Retrieve-Code = 2
BLA-number = 2
BLA-subscription-period = 2
SIP-send-MAC = 2
SIP-send-line = 2
SIP-Reg-retry-timer = 2
conference-type = 2
conference-uri = 2
ACD-subscrip-period = 2
Earlymedia = 2
SIPServerType = 2
Music-ServerURI = 2
Direct-Call-Pickup-Code = 2
Group-Call-Pickup-Code = 2
Distinctive-Ring-Tones = 2
UnregisterOnReboot = 2
Out-Dialog-BLF = 2
RTCP-Collector-Name = 2
RTCP-Collector-Address = 2
RTCP-Collector-Port = 2
Number-Of-Linekey = 1
subscribe-register = 2
[ Network ]
network-basic = 0
network-pcport = 0
network-advanced = 0
network-wifi = 0
shotlevel = 0
[ Network-Basic ]
ipaddress-mode = 2
ipv4config = 2
ipv6config = 2
121
Configuration Guide for User Access Level
wan-ppoe = 2
[ Network-PCPort ]
pcport-active = 0
[ Network-Advanced ]
LLDP-items = 2
CDP-items = 2
VLAN-items = 2
NAT-items = 2
port-link = 2
voice-QoS = 2
local-RTP-port = 2
web-server = 2
8021x = 2
span-to-pc-port = 2
reg-surge-prev = 2
ICMPv6_Status = 2
open-VPN = 2
reserve-port = 0
[Network-Wifi]
wifi-active = 2
wifi-list = 2
wifi-label = 2
wifi-ssid = 2
wifi-mode = 2
wifi-type = 2
wifi-psk = 2
wifi-edit = 2
wifi-status-detection-timeout = 0
[ DSSKey ]
memorykey = 0
linekey = 0
programmablekey = 0
extkey = 0
[ MemoryKey ]
memory-key = 0
[ LineKey ]
line-key = 0
122
Configuration Guide for User Access Level
Enable-Page-Tips = 0
Label-Length = 0
[ ProgramKey ]
programmable-key = 0
[ ExtKey ]
ext-key = 0
[ Features ]
features-forward = 0
features-general = 0
features-audio = 0
features-intercom = 0
features-transfer = 0
features-callpickup = 0
features-remote = 0
features-phonelock = 0
features-acd = 0
features-sms = 0
features-actionurl = 0
features-bluetooth = 0
features-powerled = 0
features-notifypop = 0
[ Forward&DND ]
head-forward = 0
forward-mode = 0
forward-account = 0
always-forward = 0
always-forward-enabled = 0
always-forward-target = 0
always-forward-OnCode = 0
always-forward-OffCode = 0
busy-forward = 0
busy-forward-enabled = 0
busy-forward-target = 0
busy-forward-OnCode = 0
busy-forward-OffCode = 0
NoAnswer-forward = 0
NoAnswer-forward-enabled = 0
NoAnswer-forward-ringtimes = 0
NoAnswer-forward-target = 0
123
Configuration Guide for User Access Level
NoAnswer-forward-OnCode = 0
NoAnswer-forward-OffCode = 0
DND = 0
DND-Emergency = 0
DND-Authorized-Numbers = 0
DND-mode = 01
DND-account = 01
DND-Status = 01
DND-OnCode = 01
DND-OffCode = 01
forward-emergency = 0
forward-authorized-numbers = 0
[ General-Information ]
call_waiting = 0
auto-redial = 0
auto_redial_interval = 0
auto_redial_times = 0
key_as_send = 0
reserve-pound = 2
hotline-number = 0
hotline-delay = 0
busytone_delay = 0
return-code-refuse = 0
return-code-DND = 0
call_completion = 0
feature-key-synchronisation = 0
TimeOut-for-DialNow = 0
RFC-2543-Hold = 2
use-outbound-in-dialog = 2
IsDeal-180 = 2
logon-wizard = 2
PswPrefix = 2
PswLength = 2
PswDial = 2
SaveCallHistory = 2
SuppressDTMFDisplay = 1
SuppressDTMFDisplayDelay = 1
play-local-DTMF-tone = 0
DTMFRepetition = 0
MulticastCodec = 0
PlayHoldTone = 0
PlayHoldToneDelay = 0
124
Configuration Guide for User Access Level
AllowMute = 0
DualHeadset = 1
AutoAnswerDelay = 0
HeadsetPrior = 0
DTMFReplaceTran = 0
TranSendDTMF = 1
SendPoundKey = 0
FwdInternational = 0
Diversion-History-Info = 1
allow-trans-exist-call = 0
ReLogOffTime = 2
call-number-filter = 0
Use_Logo = 0
upload_logo = 0
allow-IP-call = 0
IP-direct-auto-answer = 0
calllog-show-num = 0
voicemail-tone = 0
DHCP-hostname = 0
EnableAutoFavorite = 0
reboot-in-talking = 0
Hide-Feature-Access-Codes = 0
display-method-on-dialing = 2
calllog-show-num = 0
auto-linekeys = 1
sip-trust-control = 2
enable-auto-answer-tone = 0
[ Features-Audio ]
call-waiting-tone = 0
button-sound = 0
redial_tone = 0
send-sound = 0
headset-send-volume = 1
handset-send-volume = 1
handfree-send-volume = 1
Ringer_Dev = 0
[ Features-Intercom ]
allow-intercom = 0
intercom-mute = 0
intercom-tone = 0
intercom-barge = 0
125
Configuration Guide for User Access Level
[ Features-Transfer ]
semi-attend-transfer = 0
blind-tran-onhook = 0
Semi-Attend-Trans-OnHook = 0
transfer-on-conference-hang-up = 0
TransferModeViaDsskey = 0
[ Features-Callpickup ]
Call-Pickup = 0
Call-Park = 0
[ Features-Remote ]
pushxml-server-addr = 2
XMLSIPNotify = 2
XMLBlockInCalling = 1
ActionURILimitIP = 2
[ Features-Lock ]
Lock_Enable = 2
keyboard_lock = 2
Phone_Unlock_PIN = 2
Phone_lock_time_out = 2
emergency_setting = 2
[ Features-ACD ]
ACD-auto-available = 2
ACD-auto-available-timer = 2
[ Features-SMS ]
send-sms = 0
[ Features-ActionURL ]
setup-complete = 2
log-on = 2
log-off = 2
register-fail = 2
off-hook = 2
on-hook = 2
incoming-call = 2
outgoing-call = 2
call-establish = 2
Call-Terminated = 2
DND-On = 2
DND-Off = 2
126
Configuration Guide for User Access Level
Forward-On-Code = 2
Forward-Off-Code = 2
Busy-Forward-On = 2
Busy-Forward-Off = 2
No-Answer-Forward-On = 2
No-Answer-Forward-Off = 2
TransferCall = 2
Blind-transfer-call = 2
Attended-transfer-call = 2
Hold = 2
Unhold = 2
Mute = 2
Unmute = 2
Missed-call = 2
IPChange = 2
IdletoBusy = 2
BusytoIdle = 2
RejectIncomingCall = 2
AnswerNewInCall = 2
TransferFailed = 2
TransferFinished = 2
ForwardIncomingCall = 2
UCServer = 2
ReportIP = 2
AutopFinish = 2
OpenCallWait = 2
CloseCallWait = 2
Headset = 2
Handfree = 2
CancelCallOut = 2
RemoteBusy = 2
CallRemoteCanceled = 2
[ Features-Bluetooth ]
bluetooth-active = 0
[ Features-PowerLED ]
common-power-light-on = 0
ring-power-light-flash = 0
mail-power-light-flash = 0
mute-power-light-flash = 0
hold-power-light-flash = 0
talk-power-light-flash = 0
127
Configuration Guide for User Access Level
[ Features-NotifyPop ]
Display-Voice-Mail-Popup = 0
Display-Missed-Call-Popup = 0
Display-Forward-Call-Popup = 0
Display-Text-Message-Popup = 0
[ Settings ]
settings-preference = 0
settings-datetime = 0
settings-calldisplay = 0
settings-upgrade = 0
settings-autop = 0
settings-config = 0
settings-dialplan = 0
settings-voice = 0
settings-ring = 1
settings-tones = 0
settings-softkey = 2
settings-tr069 = 2
settings-voicemonitoring = 0
settings-sip = 1
settings-camera = 0
settings-video = 0
settings-powersaving= 0
[ Settings-Preference ]
web-language = 0
live-dialpad = 0
inter-digit-time = 0
UnusedBackLight = 0
backlight = 0
BacklightTime = 0
contrast_ctrl = 0
watchdog = 2
ring_type_setting = 0
Wallpaper = 0
screen-saver-wait-time = 0
screen-saver-type = 0
[ Time&Date ]
DHCP-Time = 0
time_zone = 0
NTP_priority = 0
prim_server = 0
128
Configuration Guide for User Access Level
sec_server = 0
update_interval = 0
daylight-time = 0
time_type = 0
daylight_date= 0
offset = 0
manual-time = 0
manual-time-settings = 0
time_format_setting = 0
date_format_setting = 0
location = 0
[ Settings-CallDisplay ]
Display-Contact-Photo = 0
Incoming-Call-Ringer-Animation = 0
Call-Display-Method = 0
[ Settings-Upgrade ]
version_info = 0
reset_to_factory = 1
reset_local_config = 0
reboot_device = 0
upgrade_firmware = 1
[ Settings-AutoProvision ]
pnp-active = 2
dhcp-active = 2
custom-option = 2
DHCP-Option-Value = 2
server-URL = 2
account = 2
password = 2
common-AES-key = 2
MAC-Oriented-AES-key = 2
zero_active = 2
wait_time = 2
poweron-active = 2
repeatly-active = 2
repeat-interval = 2
weekly-active = 2
autop-time = 2
day-of-week = 2
btn-autop-now = 2
attempt-expired-time = 2
129
Configuration Guide for User Access Level
[ Settings-Config ]
opt-configfile = 1
opt-factory-configfile = 2
export-cfg-config-file = 2
import-cfg-config-file = 2
pcap_trace = 1
syslog = 1
SystemlogLevel = 2
ExportAllDiagnosticFiles = 2
[ Settings-DialPlan ]
replace-rule = 0
dial-now = 0
area-code = 0
block-out = 0
replace-rule-control = 0
dial-now-control = 0
area-code-control = 0
block-out-control = 0
[ Settings-Voice ]
echo-cancellation = 0
jitter-buffer = 0
[ Settings-Ring ]
personal-ring = 1
[ Settings-Tones ]
tone-items = 0
[ Softkey ]
Custom_SoftKey = 2
SoftKey_Type = 2
SoftKey_Select = 2
[ TR069 ]
head = 2
EnableTR069 = 2
ACSUsername = 2
ACSPassword = 2
ACSURL = 2
EnablePeriodicInform = 2
PeriodicInformInterval = 2
130
Configuration Guide for User Access Level
RequestUsername = 2
RequestPassword = 2
[ Settings-VoiceMonitoring ]
RTCP-Session-Report = 2
RTCP-Interval-Report = 2
RTCP-Interval-Period = 2
RTCP-Warning-Moslq = 2
RTCP-Critical-Moslq = 2
RTCP-Warning-Delay = 2
RTCP-Critical-Delay = 2
Display-VQReport-On-Web = 2
Display-VQReport-On-UI = 2
RTCP-Report-Options = 2
[ Settings-SIP ]
sip-session-timer = 2
local-SIP-port = 2
TLS-SIP-Port = 2
[ Settings-Camera ]
scene-mode = 2
manual-settings = 2
exposure = 2
status-bar-icon = 2
[ Settings-Video ]
video-active = 0
auto-start-video = 0
auto-answer-video-mute = 0
uplink-bandwidth = 2
downlink-bandwidth = 2
[ Settings-PowerSaving ]
office_hour = 2
office_Monday = 2
office_Tuesday = 2
office_Wednesday = 2
office_Thursday = 2
office_Friday = 2
office_Saturday = 2
office_Sunday = 2
idle_timeout = 2
office_timeout = 2
131
Configuration Guide for User Access Level
off_timeout = 2
user_input_ext_timeout = 2
[ Contacts ]
contacts-basic = 0
contacts-remote = 0
contacts-callinfo = 0
contacts-LDAP = 0
contacts-broadsoft = 0
contacts-multicastIP = 0
contacts-favorite = 0
[ LocalPhoneBook ]
contact-list = 0
all-contacts-control = 0
import-export-contacts = 1
btnImportCSV = 1
btnExportCSV = 1
btnImportXML = 1
btnExportXML = 1
opt-contacts = 0
[ Contacts-Remote ]
remote-phonebook-list = 0
SRemoteNameEnable = 0
SRemoteNameFlashTime = 0
[ PhoneCallInfo ]
call-control = 0
dialed-list-title = 0
dialed-list-content = 0
missed-list-title = 0
missed-list-content = 0
received-list-title = 0
received-list-content = 0
forwarded-list-title = 0
forwarded-list-content = 0
[ LDAP ]
enable-LDAP = 0
LDAP-name-filter = 0
LDAP-number-filter = 0
LDAP-TLS-Mode = 0
server-address = 0
132
Configuration Guide for User Access Level
port = 0
base = 0
user-name = 0
password = 0
maxhits = 0
LDAP-name-attributes = 0
LDAP-number-attributes = 0
LDAP-display-name = 0
protocol = 0
LDAP-lookup-for-incoming-call = 0
LDAP-lookup-for-callout = 0
LDAP-sorting-results = 0
[ Contacts-Broadsoft ]
Directotries = 0
XSI = 0
[ MulticastIP ]
Receive_Priority = 0
MulticastIPConfig = 0
PagePriorityActive = 0
PagingList = 0
[ Contacts-Favorite ]
contacts-group = 0
super-search = 0
[ Security ]
password = 0
trusted_cert = 2
server_cert = 2
[ Password ]
set-password = 0
[ TrustCerts ]
trust-certs-records = 2
btn-delete-certs = 2
only-accept-trusted-certs = 2
upload-trust-certs = 2
common-name-validation = 2
ca-certs = 2
[ ServerCerts ]
133
Configuration Guide for User Access Level
server-certs-records = 2
server-certs-upload = 2
server-certs-device-cert = 2
[ HiddenSetting ]
custom-factory-config = 2
DND-Active = 2
Forward-Active = 2
Broadsoft-Active = 1
Redirect-Active = 1
UC-Active = 1
pushxml = 2
[ GUI ]
status_list= 0
Status_IP = 11
Status_IPv6 = 11
Status_MAC = 21
Status_HW = 01
Status_More = 01
network = 0
Status_More_Phone = 0
Status_More_Account = 0
Status_More_RTP = 02
status_general = 02
features= 02
CallControl = 0
callcontrol_anywhere = 11
callcontrol_remoteoffice = 11
callcontrol_forward = 11
always-forward = 1
busy-forward = 1
NoAnswer-forward = 1
callcontrol_dnd= 11
callcontrol_hidenumber = 11
callcontrol_anonymousrejection = 11
callcontrol_sinultaneousring = 11
call_waiting = 1
DSSKey = 1
key_as_send= 12
hotline-number = 1
Features_Anonymous = 1
134
Configuration Guide for User Access Level
Features_AutoRD = 1
intercom = 1
call_completion = 1
history_save= 2
multpaginglist = 10
Main_Settings = 0
time_zone = 0
Basic_Time_Manual = 0
display = 10
sound = 1
key_tone = 1
ring_type_setting = 1
unlock_pin= 2
account_label = 02
display_name = 02
register_name = 02
user_name = 01
account_password = 01
sip_server = 01
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
STUN_server = 02
auto-Answer= 1
Adv_Network = 0
wan_port_title = 02
VLAN-items = 02
wanport = 02
pcport = 02
dhcpvlan = 02
web-server = 02
8021x = 02
open-VPN = 02
open-lldp = 02
network_cdp = 02
network_nat = 02
softkey Label = 02
keyboard_lock = 02
Adv_Reboot = 02
Adv_ResetToFac = 2
password = 0
135
Configuration Guide for User Access Level
Adv_AES = 02
autoprovision = 02
international-forward = 02
SMS= 12
MSG_Voice = 1
viewvoicemail = 1
setvoicemail = 1
usermodeentry = 0
NAT_traversal = 02
contrast_ctrl = 0
callcontrol_initialacdstate = 11
callcontrol_setacdstate = 11
Main_Contacts = 0
local_contact_list = 0
remote_contact_list = 0
broadsoft_contact_list = 0
blacklist_list = 0
call_info= 0
local_call_log_list = 01
Adv_Account = 2
Basic_LANG = 0
Basic_Setting_BackLight = 0
Basic_Time_Format = 0
Basic_Time_SNTP = 0
MSG_Text = 0
SMS_Draftbox = 0
SMS_Inbox = 0
SMS_NEW = 0
SMS_Outbox = 0
SMS_Sentbox = 0
Set_Adv = 0
Set_Basic = 0
dhcptimezone = 0
line_active = 2
status = 0
dnd= 0
advanced_call_feature_default_account = 2
advanced_call_feature_general = 1
advanced_call_feature_list = 1
136
Configuration Guide for User Access Level
broadsoft_calllog_list = 0
date_and_time_general = 0
phone_setting_list = 02
reset_and_reboot_list = 02
display_wallpaper = 1
reset_default = 0
bluetooth = 1
wifi = 2
camera_setting_interface = 00
usb_interface = 00
usb_browse_audio = 00
usb_browse_video = 00
usb_browse_photo = 00
usb_storage_property = 00
hdmi = 00
video_setting_interface = 00
proxy-fallback-interval = 01
SIP-T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T4
0P/T29G/T27P/T27G/T23P/T23G/T21(P) E2/T19(P) E2
IP Phones
The default configuration item settings in factory WebItemsLevel.cfg for
T48G/T48S/T46G/T46S/T42G/T42S/T41P/T41S/T40P/T29G/T27P/T27G/T23P/T23G/T21(P)
E2/T19(P) E2 IP phones running firmware version 81 or later are:
[ Status-Menu ]
Status-Basic = 0
Status-RTP = 0
[ Status ]
version = 0
network = 0
IPv4 = 0
IPv6 = 0
NetworkCommon = 0
AccountStatus = 0
Ext = 0
DeviceCertificate = 0
[ Account ]
137
Configuration Guide for User Access Level
account-register = 0
account-basic = 0
account-codec = 0
account-adv = 2
[ Account-Register ]
switch-account = 0
account_status = 0
line_active = 0
account_label = 0
display_name = 0
register_name = 01
user_name = 01
account_password = 01
enabled-outbound-proxy-server = 2
outbound-proxy-server = 2
backup-outbound-proxy-server = 2
proxy-fallback-interval = 2
NAT_traversal = 2
sip_server = 2
sip_server2 = 2
outbound-proxy-server-port = 2
backup-outbound-proxy-server-port = 2
[ Account-Basic ]
switch-account = 0
proxy_require = 2
send_anonymous = 1
anonymous_call_enabled = 0
anonymous_call_OnCode = 1
anonymous_call_OffCode = 1
anonymous_rejection_enabled = 0
anonymous_rejection_OnCode = 1
anonymous_rejection_OffCode = 1
misscall-log = 0
auto-answer = 0
ring-type = 0
send_anonymous_rejection_code = 0
[ Account-Codec ]
switch-account = 0
codecs-group = 0
[ Account-Adv ]
138
Configuration Guide for User Access Level
switch-account = 0
UDP_keep-alive = 2
local-SIP-port = 2
rport = 2
sip-session-timer = 2
subscribe-period = 2
DTMF_items = 2
reliable_retransmission = 2
MWI-items = 2
voice_mail = 2
caller-ID-header = 2
use-session-timer = 2
session-timer = 2
session-refresher = 2
user-equal-phone = 2
voice-encryption = 2
ptime-item = 2
share-line = 2
Call-Pull-Feature-Access-Code = 2
dialog-info-call-pickup = 2
BLF-list-URI = 2
BlfListCode = 2
BLFListBargeInCode = 2
BLF-List-Retrieve-Code = 2
BLA-number = 2
BLA-subscription-period = 2
SIP-send-MAC = 2
SIP-send-line = 2
SIP-Reg-retry-timer = 2
conference-type = 2
conference-uri = 2
ACD-subscrip-period = 2
Earlymedia = 2
SIPServerType = 2
Music-ServerURI = 2
Direct-Call-Pickup-Code = 2
Group-Call-Pickup-Code = 2
Distinctive-Ring-Tones = 2
UnregisterOnReboot = 2
Out-Dialog-BLF = 2
RTCP-Collector-Name = 2
RTCP-Collector-Address = 2
RTCP-Collector-Port = 2
voice_mail_display = 2
139
Configuration Guide for User Access Level
subscribe-register = 2
udp-keep-alive-type = 2
udp-keep-alive-interval = 2
Number-Of-Linekey = 2
[ Network ]
network-basic = 0
network-pcport = 0
network-advanced = 2
network-nat = 2
network-wifi = 0
[ Network-Basic ]
ipaddress-mode = 0
ipv4config = 0
ipv6config = 0
[ Network-PCPort ]
pcport-active = 0
[ Network-Nat ]
manual = 2
manual-switch = 2
manual-ip = 2
ICE = 2
ICE-switch = 2
STUN = 2
STUN-switch = 2
STUN-server = 2
STUN-port = 2
TURN = 2
TURN-switch = 2
TURN-server = 2
TURN-port = 2
TURN-username = 2
TURN-password = 2
[ Network-Advanced ]
LLDP-items = 2
CDP-items = 2
VLAN-items = 2
port-link = 2
voice-QoS = 2
local-RTP-port = 2
140
Configuration Guide for User Access Level
web-server = 2
8021x = 2
span-to-pc-port = 2
reg-surge-prev = 2
ICMPv6_Status = 2
open-VPN = 2
[ Network-Wifi ]
wifi-active = 0
wifi-list = 0
wifi-label = 0
wifi-ssid = 0
wifi-mode = 0
wifi-type = 0
wifi-psk = 0
[ DSSKey ]
linekey = 0
programmablekey = 0
extkey = 0
[ LineKey ]
line-key = 0
Enable-Page-Tips = 0
Label-Length = 0
[ ProgramKey ]
programmable-key = 0
[ ExtKey ]
ext-key = 0
[ Features ]
features-forward = 0
features-general = 0
features-audio = 0
features-intercom = 0
features-transfer = 0
features-callpickup = 0
features-remote = 2
features-phonelock = 0
features-acd = 2
141
Configuration Guide for User Access Level
features-sms = 0
features-actionurl = 2
features-bluetooth = 0
features-powerled = 0
features-notifypop = 0
[ Forward&DND ]
head-forward = 0
forward-mode = 0
forward-account = 0
always-forward = 0
always-forward-enabled = 0
always-forward-target = 0
always-forward-OnCode = 0
always-forward-OffCode = 0
busy-forward = 0
busy-forward-enabled = 0
busy-forward-target = 0
busy-forward-OnCode = 0
busy-forward-OffCode = 0
NoAnswer-forward = 0
NoAnswer-forward-enabled = 0
NoAnswer-forward-ringtimes = 0
NoAnswer-forward-target = 0
NoAnswer-forward-OnCode = 0
NoAnswer-forward-OffCode = 0
DND = 0
DND-Emergency = 0
DND-Authorized-Numbers = 0
DND-mode = 0
DND-account = 0
DND-Status = 0
DND-OnCode = 0
DND-OffCode = 0
forward-emergency = 0
forward-authorized-numbers = 0
[ General-Information ]
call_waiting = 0
auto-redial = 0
auto_redial_interval = 0
142
Configuration Guide for User Access Level
auto_redial_times = 0
key_as_send = 0
reserve-pound = 2
hotline-number = 0
hotline-delay = 0
busytone_delay = 0
return-code-refuse = 0
return-code-DND = 0
call_completion = 0
feature-key-synchronisation = 0
TimeOut-for-DialNow = 0
RFC-2543-Hold = 2
use-outbound-in-dialog = 2
IsDeal-180 = 2
logon-wizard = 2
PswPrefix = 0
PswLength = 0
PswDial = 0
SaveCallHistory = 2
SuppressDTMFDisplay = 1
SuppressDTMFDisplayDelay = 1
play-local-DTMF-tone = 0
DTMFRepetition = 0
MulticastCodec = 0
PlayHoldTone = 0
PlayHoldToneDelay = 0
AllowMute = 0
DualHeadset = 0
AutoAnswerDelay = 0
HeadsetPrior = 0
DTMFReplaceTran = 0
TranSendDTMF = 1
SendPoundKey = 0
FwdInternational = 0
Diversion-History-Info = 1
allow-trans-exist-call = 0
blf-led-mode = 0
ReLogOffTime = 2
call-number-filter = 0
Use_Logo = 0
upload_logo = 0
allow-IP-call = 0
IP-direct-auto-answer = 0
calllog-show-num = 0
143
Configuration Guide for User Access Level
voicemail-tone = 0
DHCP-hostname = 0
EnableAutoFavorite = 0
reboot-in-talking = 0
Hide-Feature-Access-Codes = 0
display-method-on-dialing = 2
calllog-show-num = 0
auto-linekeys = 1
sip-trust-control = 2
enable-auto-answer-tone = 0
[ Features-Audio ]
call-waiting-tone = 0
button-sound = 0
redial_tone = 0
send-sound = 0
headset-send-volume = 1
handset-send-volume = 1
handfree-send-volume = 1
Ringer_Dev = 0
[ Features-Intercom ]
allow-intercom = 0
intercom-mute = 0
intercom-tone = 0
intercom-barge = 0
[ Features-Transfer ]
semi-attend-transfer = 0
Semi-Attend-Trans-OnHook = 0
blind-tran-onhook = 0
transfer-on-conference-hang-up = 0
TransferModeViaDsskey = 0
[ Features-Callpickup ]
Call-Pickup = 0
Call-Park = 0
[ Features-Remote ]
pushxml-server-addr = 2
XMLSIPNotify = 2
XMLBlockInCalling = 2
ActionURILimitIP = 2
CSTAControl = 2
144
Configuration Guide for User Access Level
[ Features-Lock ]
Lock_Enable = 0
keyboard_lock = 0
Phone_Unlock_PIN = 0
Phone_lock_time_out = 0
emergency_setting = 0
[ Features-ACD ]
ACD-auto-available = 2
ACD-auto-available-timer = 2
[ Features-ActionURL ]
setup-complete = 2
log-on = 2
log-off = 2
register-fail = 2
off-hook = 2
on-hook = 2
incoming-call = 2
outgoing-call = 2
call-establish = 2
Call-Terminated = 2
DND-On = 2
DND-Off = 2
Forward-On-Code = 2
Forward-Off-Code = 2
Busy-Forward-On = 2
Busy-Forward-Off = 2
No-Answer-Forward-On = 2
No-Answer-Forward-Off = 2
TransferCall = 2
Blind-transfer-call = 2
Attended-transfer-call = 2
Hold = 2
Unhold = 2
Mute = 2
Unmute = 2
Missed-call = 2
IPChange = 2
IdletoBusy = 2
BusytoIdle = 2
RejectIncomingCall = 2
AnswerNewInCall = 2
145
Configuration Guide for User Access Level
TransferFailed = 2
TransferFinished = 2
ForwardIncomingCall = 2
UCServer = 2
ReportIP = 2
AutopFinish = 2
OpenCallWait = 2
CloseCallWait = 2
Headset = 2
Handfree = 2
CancelCallOut = 2
RemoteBusy = 2
CallRemoteCanceled = 2
[ Features-Bluetooth ]
bluetooth-active = 0
[ Features-PowerLED ]
common-power-light-on = 0
ring-power-light-flash = 0
mail-power-light-flash = 0
mute-power-light-flash = 0
hold-power-light-flash = 0
talk-power-light-flash = 0
misscall-power-light-flash = 0
[ Features-NotifyPop ]
Display-Voice-Mail-Popup = 0
Display-Missed-Call-Popup = 0
Display-Forward-Call-Popup = 0
Display-Text-Message-Popup = 0
[ Settings ]
settings-preference = 0
settings-datetime = 0
settings-calldisplay = 0
settings-upgrade = 0
settings-autop = 2
settings-config = 0
settings-dialplan = 2
settings-voice = 2
settings-ring = 2
146
Configuration Guide for User Access Level
settings-tones = 2
settings-softkey = 2
settings-tr069 = 2
settings-voicemonitoring = 2
settings-sip = 2
settings-powersaving = 0
[ Settings-Preference ]
web-language = 0
live-dialpad = 0
inter-digit-time = 0
transparency =0
UnusedBackLight = 0
backlight = 0
BacklightTime = 0
contrast_ctrl = 0
watchdog = 2
ring_type_setting = 0
Wallpaper = 0
ScreenSaver = 0
ScreenSaverUpload = 0
[ Settings-PowerSaving ]
enable = 2
office_timeout = 0
off_timeout = 0
user_input_ext_timeout = 0
office_hour = 0
office_Monday = 0
office_Tuesday = 0
office_Wednesday = 0
office_Thursday = 0
office_Friday = 0
office_Saturday = 0
office_Sunday = 0
idle_timeout = 0
[ Time&Date ]
DHCP-Time = 0
time_zone = 0
NTP_priority = 0
prim_server = 0
sec_server = 0
147
Configuration Guide for User Access Level
update_interval = 0
daylight-time = 0
time_type = 0
daylight_date= 0
offset = 0
manual-time = 0
manual-time-settings = 0
time_format_setting = 0
date_format_setting = 0
location = 0
[ Settings-CallDisplay ]
Display-Contact-Photo = 0
Incoming-Call-Ringer-Animation = 0
Call-Display-Method = 0
[ Settings-Upgrade ]
version_info = 0
reset_to_factory = 2
reboot_device = 0
upgrade_firmware = 0
reset = 0
reset_local_settings = 0
reset_nonstatic_settings = 0
reset_static_settings = 2
reset_userdata = 0
[ Settings-AutoProvision ]
pnp-active = 2
dhcp-active = 2
custom-option = 2
DHCP-Option-Value = 2
server-URL = 2
account = 2
password = 2
common-AES-key = 2
MAC-Oriented-AES-key = 2
zero_active = 2
wait_time = 2
poweron-active = 2
repeatly-active = 2
repeat-interval = 2
weekly-active = 2
autop-time = 2
148
Configuration Guide for User Access Level
day-of-week = 2
btn-autop-now = 2
attempt-expired-time = 2
weekly-upgrade-interval = 2
inactivity-time-expire = 2
flexible-switch = 2
flexible-interval = 2
flexible-autoptime = 2
[ Settings-Config ]
opt-configfile = 0
opt-factory-configfile = 0
export-cfg-config-file = 0
import-cfg-config-file = 0
pcap_trace = 0
ExportAllDiagnosticFiles = 0
Local_Logging = 0
Local_Log_Switch = 0
Local_Log_Level = 0
Local_Log_Max_File_Size = 0
Local_Log_Export = 0
Syslog_Switch = 2
Syslog_Server = 2
Syslog_Transport_Type = 2
Syslog_Level = 2
Syslog_Facility = 2
Syslog_Prepend_Mac = 2
[ Settings-DialPlan ]
replace-rule = 0
dial-now = 0
area-code = 0
block-out = 0
replace-rule-control = 0
dial-now-control = 0
area-code-control = 0
block-out-control = 0
[ Settings-Voice ]
149
Configuration Guide for User Access Level
echo-cancellation = 2
jitter-buffer = 2
[ Settings-Ring ]
personal-ring = 2
[ Settings-Tones ]
tone-items = 2
tone-country = 2
[ Softkey ]
Custom_SoftKey = 2
SoftKey_Type = 2
SoftKey_Select = 2
[ TR069 ]
head = 2
EnableTR069 = 2
ACSUsername = 2
ACSPassword = 2
ACSURL = 2
EnablePeriodicInform = 2
PeriodicInformInterval = 2
RequestUsername = 2
RequestPassword = 2
[ Settings-VoiceMonitoring ]
RTCP-Session-Report = 2
RTCP-Interval-Report = 2
RTCP-Interval-Period = 2
RTCP-Warning-Moslq = 2
RTCP-Critical-Moslq = 2
RTCP-Warning-Delay = 2
RTCP-Critical-Delay = 2
Display-VQReport-On-Web = 2
Display-VQReport-On-UI = 2
RTCP-Report-Options = 2
Voice-RTCP-XR-REPORT = 2
[ Settings-SIP ]
sip-session-timer = 2
local-SIP-port = 2
TLS-SIP-Port = 2
150
Configuration Guide for User Access Level
[ Contacts ]
contacts-basic = 0
contacts-remote = 1
contacts-callinfo = 0
contacts-LDAP = 1
contacts-broadsoft = 0
contacts-multicastIP = 1
contacts-favorite = 0
[ LocalPhoneBook ]
contact-list = 0
all-contacts-control = 0
import-export-contacts = 0
btnImportCSV = 0
btnExportCSV = 0
btnImportXML = 0
btnExportXML = 0
opt-contacts = 0
[ Contacts-Remote ]
remote-phonebook-list = 1
SRemoteNameEnable = 1
SRemoteNameFlashTime = 1
[ PhoneCallInfo ]
call-control = 0
dialed-list = 0
missed-list = 0
received-list = 0
forwarded-list = 0
[ LDAP ]
enable-LDAP = 0
LDAP-name-filter = 0
LDAP-number-filter = 0
LDAP-TLS-Mode = 0
server-address = 0
port = 0
base = 0
user-name = 0
password = 0
maxhits = 0
151
Configuration Guide for User Access Level
LDAP-name-attributes = 0
LDAP-number-attributes = 0
LDAP-display-name = 0
protocol = 0
LDAP-lookup-for-incoming-call = 0
LDAP-lookup-for-callout = 0
LDAP-sorting-results = 0
[ Apps ]
broadsoft-XSI = 1
broadsoft-XMPP = 1
[ Broadsoft ]
XSI = 1
Directotries = 1
XMPP-accout = 1
XMPP-userame = 1
XMPP-password = 1
CallLog = 1
[ MulticastIP ]
Receive_Priority = 1
MulticastIPConfig = 1
PagePriorityActive = 1
PagingList = 1
[ Contacts-Favorite ]
contacts-group = 0
super-search = 0
[ Security ]
password = 0
trusted_cert = 2
server_cert = 2
[ TrustCerts ]
trust-certs-records = 2
btn-delete-certs = 2
only-accept-trusted-certs = 2
upload-trust-certs = 2
common-name-validation = 2
ca-certs = 2
152
Configuration Guide for User Access Level
[ ServerCerts ]
server-certs-records = 2
server-certs-upload = 2
server-certs-device-cert = 2
[ HiddenSetting ]
custom-factory-config = 2
DND-Active = 2
Forward-Active = 2
Broadsoft-Active = 2
Redirect-Active = 2
UC-Active = 2
pushxml = 2
XSI-Active = 2
remote_pcap = 2
remote_pcap_switch = 2
remote_pcap_port = 2
remote_pcap_password = 2
[ GUI ]
status_list= 0
Status_IP = 0
Status_IPv6 = 0
Status_MAC = 0
Status_HW = 0
Status_More = 0
network = 0
Status_More_Phone = 0
Status_More_Account = 0
Status_More_RTP = 0
status_general = 0
softkey Label = 0
features= 0
CallControl = 1
callcontrol_anywhere = 1
callcontrol_remoteoffice = 1
callcontrol_forward = 1
always-forward = 0
busy-forward = 0
NoAnswer-forward = 0
callcontrol_dnd= 1
callcontrol_hidenumber = 1
callcontrol_anonymousrejection = 1
callcontrol_sinultaneousring = 1
153
Configuration Guide for User Access Level
callcontrol_mobility =1
callcontrol_group_night_forward =1
callcontrol_callwaiting =1
callcontrol_forward_selective =1
callcontrol_executive =1
callcontrol_securityclassification =1
callcontrol_executive_assistant =1
call_waiting = 0
DSSKey = 0
key_as_send= 0
hotline-number = 0
Features_Anonymous = 0
Features_AutoRD = 0
intercom = 0
call_completion = 0
history_save= 2
multpaginglist = 2
Main_Settings= 0
time_zone = 0
Basic_Time_Manual = 0
display = 0
sound = 0
key_tone = 0
ring_type_setting = 0
unlock_pin= 0
account_label = 0
display_name = 0
register_name = 01
user_name = 01
account_password = 01
sip_server = 2
enabled-outbound-proxy-server = 2
outbound-proxy-server = 2
STUN_server = 2
auto-Answer= 0
Adv_Network = 0
wan_port_title = 0
VLAN-items = 2
wanport = 0
pcport = 2
dhcpvlan = 2
web-server = 2
154
Configuration Guide for User Access Level
8021x = 2
open-VPN = 2
open-lldp = 2
network_cdp = 2
network_nat = 2
keyboard_lock = 0
Adv_Reboot = 0
Adv_ResetToFac = 2
password = 0
autoprovision = 2
international-forward = 2
SMS= 0
MSG_Voice = 0
viewvoicemail = 0
setvoicemail = 0
usermodeentry = 0
NAT_traversal = 2
contrast_ctrl = 0
broadsoft_contact_list = 1
callcontrol_initialacdstate = 1
callcontrol_setacdstate = 1
Main_Contacts = 0
local_contact_list = 0
remote_contact_list = 0
blacklist_list = 0
call_info= 0
local_call_log_list = 0
Adv_Account = 0
Basic_LANG = 0
Basic_Setting_BackLight = 0
Basic_Time_Format = 0
Basic_Time_SNTP = 0
MSG_Text = 0
SMS_Draftbox = 0
SMS_Inbox = 0
SMS_NEW = 0
SMS_Outbox = 0
SMS_Sentbox = 0
Set_Adv = 0
Set_Basic = 0
dhcptimezone = 0
line_active = 0
status = 0
155
Configuration Guide for User Access Level
dnd= 0
advanced_call_feature_default_account = 0
advanced_call_feature_general = 0
advanced_call_feature_list = 0
broadsoft_calllog_list = 0
date_and_time_general = 0
reset_and_reboot_list = 0
bluetooth = 0
display_wallpaper = 0
reset_default = 0
wifi = 0
Features_Diagnostics = 0
Diagnostics_Network = 0
Diagnostics_Ping = 0
Diagnostics_TraceRoute = 0
display_dsskey_wallpaper = 0
usb_record= 0
browse_usb_record= 0
browse_usb_storage= 0
Adv_ResetConfig = 0
ResetLocalConfig = 0
ResetNonStaticConfig = 0
ResetStaticConfig = 2
callcontrol_securityclassification = 0
ResetUserDataUserCfg = 0
check_key_guard_lock = 0
screensaver = 0
blf_ring_setting = 0
CP860 IP Phones
The default configuration item settings in factory WebItemsLevel.cfg for CP860 IP phones
running firmware version 80 or later are:
[ Status-Menu ]
Status-Basic = 0
Status-RTP = 0
[ Status ]
version = 0
network = 0
IPv4 = 0
IPv6 = 0
156
Configuration Guide for User Access Level
NetworkCommon = 0
AccountStatus = 0
Ext = 0
[ Account ]
account-register = 0
account-basic = 0
account-codec = 0
account-adv = 0
[ Account-Register ]
switch-account = 0
account_status = 0
line_active = 0
account_label = 0
display_name = 0
register_name = 01
user_name = 01
account_password = 2
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
transport-item = 2
backup-outbound-proxy-server = 01
proxy-fallback-interval = 01
NAT_traversal = 2
sip_server = 2
[ Account-Basic ]
switch-account = 0
proxy_require = 0
send_anonymous = 1
anonymous_call_enabled = 0
anonymous_call_OnCode = 1
anonymous_call_OffCode = 1
anonymous_rejection_enabled = 0
anonymous_rejection_OnCode = 1
anonymous_rejection_OffCode = 1
misscall-log = 0
auto-answer = 0
ring-type = 0
send_anonymous_rejection_code = 0
auto-answer-mute = 0
[ Account-Codec ]
157
Configuration Guide for User Access Level
switch-account = 0
codecs-group = 0
[ Account-Adv ]
switch-account = 0
UDP_keep-alive = 2
local-SIP-port = 2
rport = 2
sip-session-timer = 2
subscribe-period = 2
DTMF_items = 2
reliable_retransmission = 2
MWI-items = 2
voice_mail = 0
caller-ID-header =2
use-session-timer = 2
session-timer = 2
session-refresher = 2
user-equal-phone = 2
voice-encryption = 2
ptime-item = 2
share-line = 2
Call-Pull-Feature-Access-Code = 2
dialog-info-call-pickup = 2
BLF-list-URI = 2
BlfListCode = 2
BLFListBargeInCode = 2
BLF-List-Retrieve-Code = 2
BLA-number = 2
BLA-subscription-period = 2
SIP-send-MAC = 2
SIP-send-line = 2
SIP-Reg-retry-timer = 2
conference-type = 2
conference-uri = 2
ACD-subscrip-period = 2
Earlymedia = 2
SIPServerType = 2
Music-ServerURI = 2
Direct-Call-Pickup-Code = 2
Group-Call-Pickup-Code = 2
Distinctive-Ring-Tones = 2
UnregisterOnReboot = 2
Out-Dialog-BLF = 2
158
Configuration Guide for User Access Level
RTCP-Collector-Name = 2
RTCP-Collector-Address = 2
RTCP-Collector-Port = 2
Number-Of-Linekey = 1
voice_mail_display = 2
subscribe-register = 2
[ Network ]
network-basic = 0
network-pcport = 0
network-advanced = 0
shotlevel = 0
[ Network-Basic ]
ipaddress-mode = 2
ipv4config = 2
ipv6config = 2
wan-ppoe = 2
[ Network-PCPort ]
pcport-active = 0
[ Network-Advanced ]
LLDP-items = 2
CDP-items = 2
VLAN-items = 2
NAT-items = 2
port-link = 2
voice-QoS = 2
local-RTP-port = 2
web-server = 2
8021x = 2
span-to-pc-port = 2
reg-surge-prev = 2
ICMPv6_Status = 2
open-VPN = 2
[ DSSKey ]
memorykey = 0
linekey = 0
programmablekey = 0
extkey = 0
[ MemoryKey ]
159
Configuration Guide for User Access Level
memory-key = 0
[ LineKey ]
line-key = 0
Enable-Page-Tips = 0
Label-Length = 0
[ ProgramKey ]
programmable-key = 0
[ ExtKey ]
ext-key = 0
[ Features ]
features-forward = 0
features-general = 0
features-audio = 0
features-intercom = 0
features-transfer = 0
features-callpickup = 0
features-remote = 0
features-phonelock = 0
features-acd = 0
features-sms = 0
features-actionurl = 0
features-powerled = 0
features-notifypop = 0
[ Forward&DND ]
head-forward = 0
forward-mode = 0
forward-account = 0
always-forward = 0
always-forward-enabled = 0
always-forward-target = 0
always-forward-OnCode = 0
always-forward-OffCode = 0
busy-forward = 0
busy-forward-enabled = 0
busy-forward-target = 0
busy-forward-OnCode = 0
busy-forward-OffCode = 0
NoAnswer-forward = 0
160
Configuration Guide for User Access Level
NoAnswer-forward-enabled = 0
NoAnswer-forward-ringtimes = 0
NoAnswer-forward-target = 0
NoAnswer-forward-OnCode = 0
NoAnswer-forward-OffCode = 0
DND = 0
DND-Emergency = 0
DND-Authorized-Numbers = 0
DND-mode = 01
DND-account = 01
DND-Status = 01
DND-OnCode = 01
DND-OffCode = 01
forward-emergency = 0
forward-authorized-numbers = 0
[ General-Information ]
call_waiting = 0
auto-redial = 0
auto_redial_interval = 0
auto_redial_times = 0
key_as_send = 0
reserve-pound = 2
hotline-number = 0
hotline-delay = 0
busytone_delay = 0
return-code-refuse = 0
return-code-DND = 0
call_completion = 0
feature-key-synchronisation = 0
TimeOut-for-DialNow = 0
RFC-2543-Hold = 2
use-outbound-in-dialog = 2
IsDeal-180 = 2
logon-wizard = 2
PswPrefix = 2
PswLength = 2
PswDial = 2
SaveCallHistory = 2
SuppressDTMFDisplay = 1
SuppressDTMFDisplayDelay = 1
play-local-DTMF-tone = 0
DTMFRepetition = 0
161
Configuration Guide for User Access Level
MulticastCodec = 0
PlayHoldTone = 0
PlayHoldToneDelay = 0
AllowMute = 0
DualHeadset = 1
AutoAnswerDelay = 0
HeadsetPrior = 0
DTMFReplaceTran = 0
TranSendDTMF = 1
SendPoundKey = 0
FwdInternational = 0
Diversion-History-Info = 1
allow-trans-exist-call = 0
ReLogOffTime = 2
call-number-filter = 0
Use_Logo = 0
upload_logo = 0
allow-IP-call = 0
IP-direct-auto-answer = 0
calllog-show-num = 0
voicemail-tone = 0
DHCP-hostname = 0
EnableAutoFavorite = 0
reboot-in-talking = 0
Hide-Feature-Access-Codes = 0
display-method-on-dialing = 2
calllog-show-num = 0
auto-linekeys = 1
sip-trust-control = 2
enable-auto-answer-tone = 0
[ Features-Audio ]
call-waiting-tone = 0
button-sound = 0
redial_tone = 0
send-sound = 0
headset-send-volume = 1
handset-send-volume = 1
handfree-send-volume = 1
Ringer_Dev = 0
[ Features-Intercom ]
allow-intercom = 0
intercom-mute = 0
162
Configuration Guide for User Access Level
intercom-tone = 0
intercom-barge = 0
[ Features-Transfer ]
semi-attend-transfer = 0
Semi-Attend-Trans-OnHook = 0
blind-tran-onhook = 0
transfer-on-conference-hang-up = 0
TransferModeViaDsskey = 0
[ Features-Callpickup ]
Call-Pickup = 0
Call-Park = 0
[ Features-Remote ]
pushxml-server-addr = 2
XMLSIPNotify = 2
XMLBlockInCalling = 1
ActionURILimitIP = 2
[ Features-Lock ]
Lock_Enable = 2
keyboard_lock = 2
Phone_Unlock_PIN = 2
Phone_lock_time_out = 2
emergency_setting = 2
[ Features-ACD ]
ACD-auto-available = 2
ACD-auto-available-timer = 2
[ Features-ActionURL ]
setup-complete = 2
log-on = 2
log-off = 2
register-fail = 2
off-hook = 2
on-hook = 2
incoming-call = 2
outgoing-call = 2
call-establish = 2
Call-Terminated = 2
DND-On = 2
DND-Off = 2
163
Configuration Guide for User Access Level
Forward-On-Code = 2
Forward-Off-Code = 2
Busy-Forward-On = 2
Busy-Forward-Off = 2
No-Answer-Forward-On = 2
No-Answer-Forward-Off = 2
TransferCall = 2
Blind-transfer-call = 2
Attended-transfer-call = 2
Hold = 2
Unhold = 2
Mute = 2
Unmute = 2
Missed-call = 2
IPChange = 2
IdletoBusy = 2
BusytoIdle = 2
RejectIncomingCall = 2
AnswerNewInCall = 2
TransferFailed = 2
TransferFinished = 2
ForwardIncomingCall = 2
UCServer = 2
ReportIP = 2
AutopFinish = 2
OpenCallWait = 2
CloseCallWait = 2
Headset = 2
Handfree = 2
CancelCallOut = 2
RemoteBusy = 2
[ Features-PowerLED ]
common-power-light-on = 0
ring-power-light-flash = 0
mail-power-light-flash = 0
mute-power-light-flash = 0
hold-power-light-flash = 0
talk-power-light-flash = 0
[ Features-NotifyPop ]
Display-Voice-Mail-Popup = 0
Display-Missed-Call-Popup = 0
Display-Forward-Call-Popup = 0
164
Configuration Guide for User Access Level
Display-Text-Message-Popup = 0
[ Settings ]
settings-preference = 0
settings-datetime = 0
settings-calldisplay = 0
settings-upgrade = 0
settings-autop = 0
settings-config = 0
settings-dialplan = 0
settings-voice = 0
settings-ring = 1
settings-tones = 0
settings-softkey = 2
settings-tr069 = 2
settings-voicemonitoring = 0
settings-sip = 1
[ Settings-Preference ]
web-language = 0
live-dialpad = 0
inter-digit-time = 0
UnusedBackLight = 0
backlight = 0
BacklightTime = 0
contrast_ctrl = 0
watchdog = 2
ring_type_setting = 0
Wallpaper = 0
[ Time&Date ]
DHCP-Time = 0
time_zone = 0
NTP_priority = 0
prim_server = 0
sec_server = 0
update_interval = 0
daylight-time = 0
time_type = 0
daylight_date= 0
offset = 0
manual-time = 0
manual-time-settings = 0
time_format_setting = 0
165
Configuration Guide for User Access Level
date_format_setting = 0
location = 0
[ Settings-CallDisplay ]
Display-Contact-Photo = 0
Incoming-Call-Ringer-Animation = 0
Call-Display-Method = 0
[ Settings-Upgrade ]
version_info = 0
reset_to_factory = 1
reset = 2
reset_local_config = 0
reboot_device = 0
upgrade_firmware = 1
[ Settings-AutoProvision ]
pnp-active = 2
dhcp-active = 2
custom-option = 2
DHCP-Option-Value = 2
server-URL = 2
account = 2
password = 2
common-AES-key = 2
MAC-Oriented-AES-key = 2
zero_active = 2
wait_time = 2
poweron-active = 2
repeatly-active = 2
repeat-interval = 2
weekly-active = 2
autop-time = 2
day-of-week = 2
btn-autop-now = 2
attempt-expired-time = 2
[ Settings-Config ]
opt-configfile = 1
opt-factory-configfile = 2
export-cfg-config-file = 2
import-cfg-config-file = 2
pcap_trace = 1
syslog = 1
166
Configuration Guide for User Access Level
SystemlogLevel = 2
ExportAllDiagnosticFiles = 2
[ Settings-DialPlan ]
replace-rule = 0
dial-now = 0
area-code = 0
block-out = 0
replace-rule-control = 0
dial-now-control = 0
area-code-control = 0
block-out-control = 0
[ Settings-Voice ]
echo-cancellation = 0
jitter-buffer = 0
[ Settings-Ring ]
personal-ring = 1
[ Settings-Tones ]
tone-items = 0
[ Softkey ]
Custom_SoftKey = 2
SoftKey_Type = 2
SoftKey_Select = 2
[ TR069 ]
head = 2
EnableTR069 = 2
ACSUsername = 2
ACSPassword = 2
ACSURL = 2
EnablePeriodicInform = 2
PeriodicInformInterval = 2
RequestUsername = 2
RequestPassword = 2
[ Settings-VoiceMonitoring ]
RTCP-Session-Report = 2
RTCP-Interval-Report = 2
RTCP-Interval-Period = 2
RTCP-Warning-Moslq = 2
167
Configuration Guide for User Access Level
RTCP-Critical-Moslq = 2
RTCP-Warning-Delay = 2
RTCP-Critical-Delay = 2
Display-VQReport-On-Web = 2
Display-VQReport-On-UI = 2
RTCP-Report-Options = 2
[ Settings-SIP ]
sip-session-timer = 2
local-SIP-port = 2
TLS-SIP-Port = 2
[ Contacts ]
contacts-basic = 0
contacts-remote = 0
contacts-callinfo = 0
contacts-LDAP = 0
contacts-broadsoft = 0
contacts-multicastIP = 0
contacts-favorite = 0
[ LocalPhoneBook ]
contact-list = 0
all-contacts-control = 0
import-export-contacts = 1
btnImportCSV = 1
btnExportCSV = 1
btnImportXML = 1
btnExportXML = 1
opt-contacts = 0
[ Contacts-Remote ]
remote-phonebook-list = 0
SRemoteNameEnable = 0
SRemoteNameFlashTime = 0
[ PhoneCallInfo ]
call-control = 0
dialed-list-title = 0
dialed-list-content = 0
missed-list-title = 0
missed-list-content = 0
received-list-title = 0
received-list-content = 0
168
Configuration Guide for User Access Level
forwarded-list-title = 0
forwarded-list-content = 0
[ LDAP ]
enable-LDAP = 0
LDAP-name-filter = 0
LDAP-number-filter = 0
LDAP-TLS-Mode = 0
server-address = 0
port = 0
base = 0
user-name = 0
password = 0
maxhits = 0
LDAP-name-attributes = 0
LDAP-number-attributes = 0
LDAP-display-name = 0
protocol = 0
LDAP-lookup-for-incoming-call = 0
LDAP-lookup-for-callout = 0
LDAP-sorting-results = 0
[ Contacts-Broadsoft ]
Directotries = 0
XSI = 0
[ MulticastIP ]
Receive_Priority = 0
MulticastIPConfig = 0
PagePriorityActive = 0
PagingList = 0
[ Contacts-Favorite ]
contacts-group = 0
super-search = 0
[ Security ]
password = 0
trusted_cert = 2
server_cert = 2
[ TrustCerts ]
trust-certs-records = 2
btn-delete-certs = 2
169
Configuration Guide for User Access Level
only-accept-trusted-certs = 2
upload-trust-certs = 2
common-name-validation = 2
ca-certs = 2
[ ServerCerts ]
server-certs-records = 2
server-certs-upload = 2
server-certs-device-cert = 2
[ HiddenSetting ]
custom-factory-config = 2
DND-Active = 2
Forward-Active = 2
Broadsoft-Active = 1
Redirect-Active = 1
UC-Active = 1
pushxml = 2
[ GUI ]
status_list= 0
Status_IP = 11
Status_IPv6 = 11
Status_MAC = 21
Status_HW = 01
Status_More = 01
network = 0
Status_More_Phone = 0
Status_More_Account = 0
Status_More_RTP = 02
status_general = 02
features= 02
CallControl = 0
callcontrol_anywhere = 11
callcontrol_remoteoffice = 11
callcontrol_forward = 11
always-forward = 1
busy-forward = 1
NoAnswer-forward = 1
callcontrol_dnd= 11
callcontrol_hidenumber = 11
callcontrol_anonymousrejection = 11
callcontrol_sinultaneousring = 11
170
Configuration Guide for User Access Level
call_waiting = 1
DSSKey = 1
key_as_send= 12
hotline-number = 1
Features_Anonymous = 1
Features_AutoRD = 1
intercom = 1
call_completion = 1
history_save= 2
multpaginglist = 10
Main_Settings = 0
time_zone = 0
Basic_Time_Manual = 0
display = 10
sound = 1
key_tone = 1
ring_type_setting = 1
unlock_pin= 2
account_label = 02
display_name = 02
register_name = 02
user_name = 01
account_password = 01
sip_server = 01
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
STUN_server = 02
auto-Answer= 1
Adv_Network = 0
wan_port_title = 02
VLAN-items = 02
wanport = 02
pcport = 02
dhcpvlan = 02
web-server = 02
8021x = 02
open-VPN = 02
open-lldp = 02
network_cdp = 02
171
Configuration Guide for User Access Level
network_nat = 02
softkey Label = 02
keyboard_lock = 02
Adv_Reboot = 02
Adv_ResetToFac = 2
password = 0
Adv_AES = 02
autoprovision = 02
international-forward = 02
SMS= 12
MSG_Voice = 1
viewvoicemail = 1
setvoicemail = 1
usermodeentry = 0
NAT_traversal = 02
contrast_ctrl = 0
broadsoft_contact_list = 0
callcontrol_initialacdstate = 11
callcontrol_setacdstate = 11
Main_Contacts = 0
local_contact_list = 0
remote_contact_list = 0
blacklist_list = 0
call_info= 0
local_call_log_list = 01
Adv_Account = 2
Basic_LANG = 0
Basic_Setting_BackLight = 0
Basic_Time_Format = 0
Basic_Time_SNTP = 0
MSG_Text = 0
SMS_Draftbox = 0
SMS_Inbox = 0
SMS_NEW = 0
SMS_Outbox = 0
SMS_Sentbox = 0
Set_Adv = 0
Set_Basic = 0
dhcptimezone = 0
172
Configuration Guide for User Access Level
line_active = 2
status = 0
dnd= 0
reset_default = 0
usb-record = 0
browserecordfiles = 0
browseusbstorge = 0
W56P IP DECT Phones
The default configuration item settings in factory WebItemsLevel.cfg for W56P IP DECT phones
running firmware version 80 or later are:
[ Status-Menu ]
Status-Basic = 0
Status-RTP = 3
Status-VoIP = 0
[ Status ]
version = 0
network = 0
IPv4 = 0
NetworkCommon = 0
[ Status-VoIP ]
registered-handset = 0
registered-new-handset = 0
voip-status = 0
paging = 0
[ Account ]
account-register = 0
account-basic = 0
account-codec = 0
account-adv = 0
account-assign = 0
account-handsetname = 0
[ Account-Register ]
173
Configuration Guide for User Access Level
switch-account = 0
account_status = 0
line_active = 0
account_label = 0
display_name = 0
register_name = 01
user_name = 01
account_password = 2
enabled-outbound-proxy-server = 01
outbound-proxy-server = 01
transport-item = 2
backup-outbound-proxy-server = 01
proxy-fallback-interval = 01
NAT_traversal = 2
sip_server = 2
[ Account-Basic ]
switch-account = 0
proxy_require = 0
send_anonymous = 1
anonymous_call_enabled = 0
anonymous_call_OnCode = 1
anonymous_call_OffCode = 1
anonymous_rejection_enabled = 0
anonymous_rejection_OnCode = 1
anonymous_rejection_OffCode = 1
send_anonymous_rejection_code = 0
[ Account-Codec ]
switch-account = 0
codecs-group = 0
[ Account-Adv ]
switch-account = 0
UDP_keep-alive = 2
local-SIP-port = 2
rport = 2
174
Configuration Guide for User Access Level
sip-session-timer = 2
subscribe-period = 2
DTMF_items = 2
reliable_retransmission = 2
MWI-items = 2
voice_mail = 0
caller-ID-header = 2
use-session-timer = 2
session-timer = 2
session-refresher = 2
user-equal-phone = 2
voice-encryption = 2
ptime-item = 2
share-line = 2
SIP-send-MAC = 2
SIP-send-line = 2
SIP-Reg-retry-timer = 2
conference-type = 2
conference-uri = 2
SIPServerType = 2
UnregisterOnReboot = 2
RTCP-Collector-Name = 3
RTCP-Collector-Address = 3
RTCP-Collector-Port = 3
subscribe-register = 2
[ Account-Assign ]
incoming-lines = 0
outgoing-lines = 0
[ Account-Handsetname ]
handsetname = 1
[ Network ]
network-basic = 0
network-advanced = 0
shotlevel = 0
175
Configuration Guide for User Access Level
[ Network-Basic ]
ipaddress-mode = 2
ipv4config = 2
wan-ppoe = 2
[ Network-Advanced ]
LLDP-items = 2
VLAN-items = 2
NAT-items = 2
voice-QoS = 2
local-RTP-port = 2
web-server = 2
8021x = 2
reg-surge-prev = 2
open-VPN = 2
[ Features ]
features-forward = 0
features-general = 0
features-audio = 0
features-transfer = 0
features-callpickup = 0
features-phonelock = 0
features-powerled = 0
[ Forward&DND ]
head-forward = 0
forward-mode = 0
forward-account = 0
always-forward = 0
always-forward-enabled = 0
always-forward-target = 0
always-forward-OnCode = 0
always-forward-OffCode = 0
busy-forward = 0
176
Configuration Guide for User Access Level
busy-forward-enabled = 0
busy-forward-target = 0
busy-forward-OnCode = 0
busy-forward-OffCode = 0
NoAnswer-forward = 0
NoAnswer-forward-enabled = 0
NoAnswer-forward-ringtimes = 0
NoAnswer-forward-target = 0
NoAnswer-forward-OnCode = 0
NoAnswer-forward-OffCode = 0
DND = 0
DND-mode = 01
DND-account = 01
DND-Status = 01
DND-OnCode = 01
DND-OffCode = 01
[ General-Information ]
call_waiting = 0
key_as_send = 0
reserve-pound = 2
busytone_delay = 0
return-code-refuse = 0
return-code-DND = 0
feature-key-synchronisation = 0
TimeOut-for-DialNow = 0
RFC-2543-Hold = 2
use-outbound-in-dialog = 2
IsDeal-180 = 2
SaveCallHistory = 2
SuppressDTMFDisplay = 1
SuppressDTMFDisplayDelay = 1
FwdInternational = 0
Diversion-History-Info = 1
ReLogOffTime = 2
call-number-filter = 0
allow-IP-call = 0
177
Configuration Guide for User Access Level
voicemail-tone = 0
DHCP-hostname = 0
reboot-in-talking = 0
display-method-on-dialing = 2
sip-trust-control = 2
end-call-onhook = 0
[ Features-Audio ]
call-waiting-tone = 0
[ Features-Transfer ]
semi-attend-transfer = 0
Semi-Attend-Trans-OnHook = 0
blind-tran-onhook = 0
[ Features-Callpickup ]
Call-Park = 0
[ Features-Lock ]
emergency_setting = 2
[ Features-PowerLED ]
common-power-light-on = 0
ring-power-light-flash = 0
mail-power-light-flash = 0
miss-call-light-flash = 0
[ Settings ]
settings-preference = 0
settings-datetime = 0
settings-calldisplay = 0
settings-upgrade = 0
settings-autop = 0
settings-config = 0
settings-dialplan = 0
settings-voice = 0
settings-tones = 0
178
Configuration Guide for User Access Level
settings-tr069 = 2
settings-voicemonitoring = 3
settings-sip = 1
[ Settings-Preference ]
web-language = 0
watchdog = 2
[ Time&Date ]
DHCP-Time = 0
time_zone = 0
NTP_priority = 0
prim_server = 0
sec_server = 0
update_interval = 0
daylight-time = 0
time_type = 0
daylight_date = 0
offset = 0
manual-time = 0
manual-time-settings = 0
time_format_setting = 0
date_format_setting = 0
location = 0
[ Settings-CallDisplay ]
Incoming-Call-Ringer-Animation = 0
Call-Display-Method = 0
[ Settings-Upgrade ]
version_info = 0
reset_to_factory = 1
reset_local_config = 0
reboot_device = 0
upgrade_firmware = 1
upgrade_handset_firmware = 1
179
Configuration Guide for User Access Level
[ Settings-AutoProvision ]
pnp-active = 2
dhcp-active = 2
custom-option = 2
DHCP-Option-Value = 2
server-URL = 2
account = 2
password = 2
common-AES-key = 2
MAC-Oriented-AES-key = 2
poweron-active = 2
repeatly-active = 2
repeat-interval = 2
weekly-active = 2
autop-time = 2
day-of-week = 2
btn-autop-now = 2
attempt-expired-time = 2
[ Settings-Config ]
opt-configfile = 1
opt-factory-configfile = 2
export-cfg-config-file = 2
import-cfg-config-file = 2
pcap_trace = 1
syslog = 1
SystemlogLevel = 2
[ Settings-DialPlan ]
replace-rule = 0
dial-now = 0
area-code = 0
block-out = 0
replace-rule-control = 0
dial-now-control = 0
area-code-control = 0
block-out-control = 0
180
Configuration Guide for User Access Level
[ Settings-Voice ]
echo-cancellation = 0
jitter-buffer = 0
[ Settings-Tones ]
tone-items = 0
[ TR069 ]
head = 2
EnableTR069 = 2
ACSUsername = 2
ACSPassword = 2
ACSURL = 2
EnablePeriodicInform = 2
PeriodicInformInterval = 2
RequestUsername = 2
RequestPassword = 2
[ Settings-VoiceMonitoring ]
RTCP-Session-Report = 2
RTCP-Interval-Report = 2
RTCP-Interval-Period = 2
RTCP-Warning-Moslq = 2
RTCP-Critical-Moslq = 2
RTCP-Warning-Delay = 2
RTCP-Critical-Delay = 2
Display-VQReport-On-Web = 2
Display-VQReport-On-UI = 2
RTCP-Report-Options = 2
[ Settings-SIP ]
sip-session-timer = 2
local-SIP-port = 2
TLS-SIP-Port = 2
[ Contacts ]
181
Configuration Guide for User Access Level
contacts-basic = 0
contacts-remote = 0
contacts-LDAP = 0
contacts-broadsoft = 0
contacts-favorite = 0
[ Contacts-Basic ]
download-contacts = 0
import-contacts = 0
export-contacts = 0
[ Contacts-Remote ]
remote-phonebook-list = 0
SRemoteNameEnable = 0
SRemoteNameFlashTime = 0
[ LDAP ]
enable-LDAP = 0
LDAP-name-filter = 0
LDAP-number-filter = 0
LDAP-TLS-Mode = 0
server-address = 0
port = 0
base = 0
user-name = 0
password = 0
maxhits = 0
LDAP-name-attributes = 0
LDAP-number-attributes = 0
LDAP-display-name = 0
protocol = 0
LDAP-lookup-for-incoming-call = 0
LDAP-lookup-for-callout = 0
LDAP-sorting-results = 0
[ Contacts-Broadsoft ]
Directotries = 0
182
Configuration Guide for User Access Level
XSI = 0
[ Contacts-Favorite ]
contacts-group = 0
super-search = 0
[ Security ]
password = 0
trusted_cert = 2
server_cert = 2
base-pin = 0
[ BasePin ]
base-unit-pin = 0
[ TrustCerts ]
trust-certs-records = 2
btn-delete-certs = 2
only-accept-trusted-certs = 2
upload-trust-certs = 2
common-name-validation = 2
ca-certs = 2
[ ServerCerts ]
server-certs-records = 2
server-certs-upload = 2
server-certs-device-cert = 2
[ HiddenSetting ]
custom-factory-config = 2
DND-Active = 2
Forward-Active = 2
Broadsoft-Active = 1
Redirect-Active = 1
[ GUI ]
Menu_Status = 0
183
Configuration Guide for User Access Level
Base = 0
Handset = 0
LineStatus = 0
Menu_Intercom = 0
Intercom_HSXS = 0
Intercom_ALLHS = 0
Menu_VoiceMail = 0
Play_Message = 0
Set_Voice_Mail = 0
Set_Key_1 = 0
Menu_CallFeatures = 0
CallForward = 0
AlwaysForward = 0
BusyForward = 0
NoAnswerForward = 0
DND = 0
CallWaiting = 0
AnonymousRejection = 0
AnonymousCall = 0
Menu_Directory = 0
Local_Contact_List = 0
Remote_Contact_List = 0
Broadsoft_Contact_List = 0
LDAP_Contact_List = 0
Menu_Settings = 0
DateTime = 0
Audio = 0
Advisory_Tones = 0
Ring_Tones = 0
Volume = 0
Melodies = 0
184
Configuration Guide for User Access Level
Display = 0
Screen_Saver = 0
Color_Schemes = 0
Wallpaper = 0
Display_Backlight = 0
Keypad_Light = 0
Notification_Light = 0
Time_Formate = 0
Date_Formate = 0
Input_Method = 0
Shortcut = 0
Soft_Left = 0
Soft_Right = 0
Up = 0
Down = 0
Left = 0
Right = 0
Language = 0
Registration = 0
De_reg_Hadndset = 0
Select_Base = 0
Telephony = 0
Auto_Answer = 0
Auto_Intercom = 0
Default_Line = 0
Incoming_Lines = 02
Speed_Dial = 0
Blacklist = 0
SystemSettings = 0
Network = 0
Logon_Wizard = 0
Handset_Reset = 0
185
Configuration Guide for User Access Level
Change_Base_PIN = 02
Base_Reset = 02
Base_Reset_Local_Cfg = 02
Base_Restart = 02
Auto_Provision = 02
RPS = 02
Eco_Mode_Plus = 02
Eco_Mode = 0
Repeater_Mode = 02
HandsetName = 0
UpgradeFirmware = 2
Menu_History = 0
All_Calls = 0
Missed_Calls = 0
Outgoing_Calls = 0
Accepted_Calls = 0
Menu_Usermode = 0
186
Configuration Guide for User Access Level
Customer Feedback
We are striving to improve our documentation quality and we appreciate your feedback. Email your opinions and
comments to DocsFeedback@yealink.com.
187
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising