Deta Connect

Deta Connect
250W Inline Dimmer
500W Inline Relay
3000W, 3 way relay
3000W Inline Relay
Connect
9731
9732
9733
9734
Features
It is important to install these products in accordance with the fitting
instructions below. Failure to do so may render your guarantee void.
All products must be installed by a competent person in accordance with
the 17th Edition wiring regulations
3 way relay (3000W)
Inline Relay (500W)
1) Switch on the mains power
2) Connect the incoming Live and Neutral wires from the 230v
mains circuit to the right-hand live and neutral terminals as shown in
the diagram (marked L & N).
3) For each of the three separate circuits, connect the switched live
and outgoing neutral wire to the corresponding terminals as shown
in the diagram.
IMPORTANT: Remember that the maximum loading for the Relay is
3000w IN TOTAL (resistive load). Exceeding this limit could cause
damage to the device.
1.
Wiring for volts free circuit
2.
Wiring for a circuit requiring mains power.
IMPORTANT: The 3-Way Control relay is not designed to be left
exposed once it is installed, as live mains wiring is connected to the
terminals. Ensure that the device is mounted securely in a
suitable housing.
Output: max. 3000 watts for resistive load
Operating distance: 30 meter closed field.
Standby power consumption: ≦ 1w.
Output rating: 500W Max.
Dimensions: Width 68mm, Height 52mm, Depth 27mm
Standby Energy Use: Less than 1W
Setup
Operation
IMPORTANT: Make sure that the relay is accessible once installed
in order to operate the manual button for linking.
1) Press the ‘on’ button on the transmitter to turn the Linked channel on.
2) Press the ‘off’ button on the transmitter to turn the linked channel off.
3) Press the Manual buttons to toggle each Relay channel on/off
Manually.
Linking a channel with a Connect transmitter:
1) Press and hold one of the manual buttons (1 to 3) on the Relay
until the corresponding LED starts to flash.
2) Press the ‘on’ or ‘up’ button on the transmitter. The LED will flash
quickly for 2 seconds to indicate a successful pairing of that
channel.
NOTE: Each channel can be paired with up to 6 separate
transmitters at any one time.
Unlinking with a Connect transmitter:
1) Press and hold the manual button on the Inline Relay until the
LED starts to flash.
2) Press the ‘off’ or ‘down’ button on the transmitter (the LED will
flash quickly for 2 seconds to indicate a successful unlinking of that
device).
Complete Memory Reset (each channel)
1) Press and hold the manual button for the channel that needs to be
reset. Release the button once the LED begins to flash. Press and hold a
second time until the LED flashes more quickly.
2) Press (don't hold) the manual button a third time. The LED will flash
quickly for 2 seconds to indicate that the memory has been cleared.
250W Inline Dimmer
500W Inline Relay
3000W, 3 way relay
3000W Inline Relay
Connect
9731
9732
9733
9734
Inline Relay (3000W)
Inline Dimmer (250W)
The Inline Relay is designed to switch mains rated resistive loads
and is rated at up to 3000w. It is mains powered and includes a
built-in time delay switch.
The relay can be operated using any Connect Remote or other
transmitter.
The Inline Dimmer is designed to switch and dim lighting circuits rated at
up to 250w. It is mains powered and includes a rotary switch designed to
tailor the dim range. This maximises compatibility with dimmable LED
bulbs. The relay can be operated using any Connect Remote.
Setting the timer:
The Inline Relay has an automatic time delay function built-in. This
offers 8 separate time delays ranging from 3 seconds to 8 hours.
After being turned on, once the allotted time has elapsed, the relay
will automatically turn off.
Setting:
‘0’ : No timer set (default standard on/off operation).
‘3s’: Automatically turn off after 3 seconds.
‘30s’: Automatically turn off after 30 seconds.
‘1m’: Automatically turn off after 1 minute.
‘10m’: Automatically turn off after 10 minute.
‘2h’: Automatically turn off after 2 hours.
‘4h’: Automatically turn off after 4 hours.
‘8h’: Automatically turn on/off after 8 hours.
Additional independent time delays can also be set using the ‘timer’
function on the Deta Connect Smartphone app (requires the
Connect WiFi-Link).
Output: max. 3000 watts for resistive load
Operating distance: 30 meter closed field.
Standby power consumption: ≦ 1w.
Setting the Dim Range (important if using LEDs!) The Inline Dimmer
has a built-in 8 step rotary switch designed to adjust the lower end of the
dimming range of connected lamps. The purpose of this switch is to
increase compatibility with all types of dimmable LED bulbs: alternative
brands can behave differently and can require tailored dim settings to
ensure that there is no flicker at the top or bottom of the dimming range.
Any LED flickering can usually be eliminated by adjusting the dim
range using the rotary switch. To adjust to the minimum dim level,
simply turn the rotary dialler to point toward the different numbered
settings 1 to 8.
Each time the switch is repositioned (assuming that the Dimmer is
powered on), the connected LED lamps will rise to 100% brightness and
then dim down to the new minimum brightness.
Recommended Adjustment Process:
1) Start from setting 8 (smallest dim range) adjust the switch from 8 to 7.
2) Power on LEDs by pressing the manual button and test the dimming
range with a LightwaveRF remote.
3) If the LEDs light up normally, without flickering at any stage, then the
dimming range can be increased by moving the switch to setting 6 and
so on.
4) Repeat this process until setting 1 is reached. If any flickering is
observed at any point, stop and return to the previous stable setting. This
the optimum range for that particular bulb.
NOTE: Be aware that the number of LED bulbs as well as the type can
affect performance
Output: max. 20 -250w incandescent
3-60w LED
20-250w electronic transformer
40-250w inductive transformer
Operating distance: 30 meter closed field.
Standby power consumption: ≦ 1w.
Signal Range
Reliable range of operation is around 15 metres indoors and up to
100m outdoors using the Connect Link/WiFi-Link. This figure may
vary depending upon the environment; very thick walls, bodies of
water or large metal objects may interfere with radio range.
220 – 240V @ 50Hz
Voltage
NPD0519v1
December 2015
MCINS4
If the distance between the transmitter and receiver is too great to
achieve reliable operation, the Connect Signal Booster may be used in
conjunction with this product to increase the range.
Radio Frequency
433.92MHz
DETA Electrical Company Limited
Kingsway House, Laporte Way
Luton, Bedfordshire. LU4 8RJ UK
Tel; +44 (0)1582 544 544 Technical Helpline: +44(0)1582 544 548
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising