Megger® Hand-Held TDR / Cable Length Meter Megger® Hand

Megger® Hand-Held TDR / Cable Length Meter Megger® Hand
Megger® Hand-Held TDR / Cable Length Meter
•
•
•
•
•
•
•
Measures length of power, telephony, CATV & LAN cables
Determines distance to an open or short
Automatic impedance control (25, 50, 75, 100, 125, 150W)
Internal library of 39 standard cable types
Memory for 20 custom cable settings
Tone generator for cable tracing
Large, high resolution backlit LCD display
Additional Features:
Cable Calibration function allows measurement of V.O.P. (Velocity Of Propagation) in a known cable length.
Requires at least a 30ft (10m) sample.
Line Voltage Detection feature displays "OUCH" message and stops operation if voltage exceeds 6.5V.
SPECIFICATIONS
Range:
Resolution:
V.O.P.
Connector:
Power:
Battery Life:
Operating
Temperature:
-18°C to 60°C
* at 20°C for coax cables <8000 ft, telephony cables
<6000 ft, wiring <3000 ft
L
Accuracy*:
12000 ft (3.7km) at 99.9 V.O.P.
9800 ft (3.0km) at 80.0 V.O.P.
8000 ft (2.4km) at 66.0 V.O.P.
6200 ft (1.9km) at 50.0 V.O.P.
±2% of rdg ±20" at <300 ft
±2% of rdg at >300 ft
20 inches (50cm)
adjustable from 1.0% to 99.9% of the speed of light
BNC
4 AA batteries
5000 tests
TDR-900
Supplied with soft carrying case and alligator clip adapter.
ORDERING INFORMATION
ME/TDR900
Hand-Held TDR/Cable Length Meter
Megger® Hand-Held TTR
SPECIFICATIONS
L
TEST
EQUIPMENT
Excitation Voltage:
TTR20
8 V rms for testing distribution or power transformers & PTs;
0.5, 1.5, or 8 V ac rms for testing CTs (switched
automatically if current exceeds a preset value)
Test Frequency:
55 Hz
Excitation Current:
Range 0 to 100 mA, 4-digit resolution
Turns Ratio Range:
0.8 to 10000, 5-digit resolution
Transformer Polarity:
Normal or reversed
Current Accuracy:
2% of reading ±1 digit
Turns Ratio Accuracy:
0.1% (0.8 to 2000)
0.15% (2001 to 4000)
0.25% (4001 to 10,000)
Measuring Time:
Less than 5 seconds
Measurement Method: ANSI/IEEE C57.12.90
Phase Relationship:
ANSI C57.12.70-1978
Display:
Graphic LCD, adjustable back-lighting
Safety/EMC/Vibration: IEC-1010-1, CE and ASTM D999.75
Operating Temperature: -20º C to 55°C (-5°F to 130°F), < 90% RH non-condensing
Power:
Six standard AA alkaline batteries
Battery Life:
12 hours of field operation
Dimensions:
9.5"H x 4.5"W x 1.9"D (240x115x50 mm)
• Single- and three-phase transformer testing
• Fully automatic; fast; easy-to-use; robust; lightweight
• Battery powered
• Tests turns ratio, excitation current and polarity
• Simple, one-button operation
• Quick-start guide on front panel
173
ORDERING INFORMATION
ME/TTR20
Optional Accessories
ME/35942
ME/36013
ME/35755-1
ME/35788
Handheld TTR with 6ft (1.8m) test leads
Test leads, X/H winding, 12ft (3.6m)
Test leads, X/H winding, 20ft (6m)
Battery/line power thermal printer with paper, battery pack,
charger, interface cable
Semi-hard fabric transport case
Hioki Testers
NEW
INFRARED THERMO HITESTER
TRMS AC CLAMP METER WITH LEAKAGE
• Pistol Style with Backlit LCD
• Laser Aiming Marker
• Selectable °F/°C
• Min/Max Function
• Upper/Lower Alarm Settings
• Stores 50 Measurements
• Measure to 200A TRMS AC
• Leakage with 10μA Resolution
• Recorder/Waveform Output
• Min/Max & Display Hold
• Switchable Filter
3283
3419-20
SPECIFICATIONS
Measurement Range:
Display Resolution:
Wavelength:
Emissivity:
Field of View:
Sighting:
Accuracy:
Battery (Life):
Operating Temperature:
Dimensions:
-35 to 500 °C (-31 to 932 °F)
0.1 °C (0.2 °F)
6 to 14 μm
0.17 to 1.00 by steps of 0.01
8 : 1 distance to spot
Red laser marker, 1 mW (class 2)
-35.0 to -0.1°C : ± 10 % rdg. ± 2 °C
0.0 to 100.0°C : ± 2 °C
100.1 to 500.0°C : ± 2 % rdg.
9V alkaline (80 hrs with laser & backlight off)
0-50°C (32-122°F), <80%RH (non-condensating)
1.81" × 6.77" × 4.65" (46×172×118 mm)
LAN TESTER
SPECIFICATIONS
AC Amps:
Accuracy (50/60Hz):
Frequency Response:
Frequency Measure:
Switchable Filter:
Analog Output:
Display:
Sampling Rate:
Crest Factor:
Circuit Voltage:
Power:
Wire Dia.:
Dimensions:
Rating:
10.00 mA to 200 A, 5 ranges
±1.0 % rdg. ±5 dgt. (1.5 % on 200 A range)
40 Hz to 2 kHz (on AC Amps)
100.0 or 1000 Hz, 2 ranges (±0.3 % rdg. ±1 dgt.)
180 Hz ±30 Hz /-3 dB
1 V /f.s, DC or AC mode
1000 count digital, 35 segment bargraph
2 or 4 times/sec (Slow: 1 time/3 sec)
2.5 (1.5 on 200 A range)
300 V AC rms max. (insulated wire)
9V battery or AC adapter
Ø 40 mm (1.57") max.
2.44" × 8.86" × 1.54" (62×225×39 mm)
CAT III 300V
TRMS AC CLAMP METER
• 1000A & 600V TRMS AC
• Ohms, Frequency & Continuity
• Waveform Distortion Check
• Inrush Peak Capture
• Min/Max & Display Hold
• Verify Wire Destinations
• Detect Split Pairs
• Measure Cable Length
• Check Wire & Shield Condition
3665-10
3282
SPECIFICATIONS
Cable Types:
Connectors:
Errors Detected:
Cable Length:
Direction Check:
Display:
Switch:
Battery (Life):
Dimensions:
Twisted-pair, 100Ω shielded/unshielded, CAT 3, 4, 5, 5e, 6
RJ-45 plugs
Open, short, reversed, transposed, split pairs & miswires
2-300 m, (6.6-984 ft) with 0.1 m (0.3 ft) resolution
Up to 21 cables can be identified using the supplied 9690
terminator & optional 9690-01 to 9690-04
LCD with backlight & beeper
Select between meters or feet
Two AA (50 hours)
3.4" × 5.2" × 1.3" (85×130×33 mm)
PENCIL DMM
3246
• Backlit 4199 Count LCD • Data Hold, Continuity Beeper
• Auto or Manual Ranging • Pushbutton Penlight
SPECIFICATIONS
DC Volts:
AC Volts (50-500Hz):
Ohms:
Rating:
Dimensions:
420m / 4.2 / 42 / 420 / 600V (±1.3 % rdg ± 4d)
4.2 / 42 / 420 / 600V (±2.3 % rdg ±8d)
420 / 4.2k / 42k / 420k / 4.2M / 42MΩ
(±2.0 % rdg ±4d), plus diode check
CAT III 600 V
1.2" × 1.0" × 7.2" (31×26×84 mm)
SPECIFICATIONS
AC Amps:
AC Volts (50/60Hz):
Frequency Response:
Frequency Measure:
Resistance Measure:
Temperature Measure:
Display:
Sampling Rate:
Crest Factor:
Circuit Voltage:
Power:
Wire Dia.:
Dimensions:
Rating:
30.00 / 300.0 / 1000 A (±1.0% rdg. ±5 dgt)
300.0 / 600 V (±1.0 % rdg. ±3 dgt.)
40 Hz to 1 kHz (on AC Amps/Volts)
100.0 or 1000 Hz (±0.3 % rdg. ±1 dgt.)
1k & 10k ranges
-50 to 150 °C (with Probe 9462, sold separately)
3000 count digital, 35 segment bargraph
2 or 4 times/sec (Slow: 1 time/3 sec)
2.5 (1.7 on 1000 A or 600 V range)
300 V AC rms max. (insulated wire)
9V battery (45 hours)
Ø 46 mm (1.8") max.
2.44" × 9.06" × 1.54" (62×230×39 mm)
CAT III 100V, CAT IV 600V
ORDERING INFORMATION
HK/3246
HK/3282
HK/3283
HK/3419-20
HK/3665-10
HK/HPK-1
Pencil DMM, battery included
TRMS AC Clamp Meter
TRMS AC Clamp Meter & Leakage Tester, with case & strap
Infrared Thermo HiTester, with carrying case
LAN Tester, with carrying case & 9690 Terminator
HVAC/Electrical Contractor Kit (includes 3120 Voltage Probe,
3280-10 Clamp-on Meter, 3419-20 IR Tester, 3804 DMM)
175a
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising