HSM2HOST Installation Manual
HSM2HOST 2-Way Wireless Transceiver
V1.2 Installation Manual
WARNING: This manual contains information on limitations regarding product use and function and information on the
limitations as to liability of the manufacturer. The entire manual should be carefully read.
Table of Contents
Specifications and Features
Compatible Wireless Devices
Safety Instructions
Introduction
Installation Process Overview
Controls and Indicators
Tamper
Setup and Wiring
Mounting
Connect the HSM2HOST
Enroll The HSM2HOST
Delete the HSM2HOST
Permanently Mount
Other Options
Wireless Device Setup and Programming
[804][000] Enroll Wireless Devices
[804][001]-[716] Wireless Device Configuration
[804][801] RF Jam Detect
[804][802] Wireless Supervision Window
[804][810] Wireless Option 1
[804][841] Motion Cameras
[804][901]-[905] Delete Wireless Devices
[804][921]-[925] Replace Wireless Devices
[804][990][001 – 005] Show All Devices
[804][999] Reset to Factory Defaults
[904] Placement Testing Wireless Devices
Programming Worksheets
Label Programming
[804] Wireless Programming
[804][000] Wireless Device Enrollment – Zones
[804][000] Wireless Device Enrollment – Wireless Keys
[804][000] Wireless Device Enrollment – Wireless Sirens
[804][000] Wireless Device Enrollment – Wireless Keypads
[804][000] Wireless Device Enrollment – Wireless Repeaters
[804][001]-[128] Configure Wireless Zones 1-128 (copy as needed)
[804][551]-[556] Configure Wireless Sirens 1-16 (copy as needed)
Toggle Options
Toggle Options
[804][601]-[632] Configure Wireless Keys (copy as needed)
[601]-[632] Wireless Key 1-32
[804]-[701]-[716] Wireless Keypad Programming (copy as needed)
[804][801] Jam Detect
[804][802] Supervisory Window
[804][810] Wireless Options
FCC Compliance Statement
3
4
5
6
6
6
7
8
8
8
8
9
9
9
10
10
10
10
11
11
12
12
12
13
13
13
15
15
17
18
19
19
20
20
21
22
22
23
23
24
24
26
26
26
30
HSM2HOST Installation Manual
Specifications and Features
Current Draw: 60mA
Voltage: Draws current from the PowerSeries Neo alarm controller (10.8VDC to 12.5VDC) - (Limited
Power Supply)
UL)
l Frequency: 433MHz (HSM2HOST4), 868MHz (HSM2HOST8), 912-919MHz (HSM2HOST9
l Zones - can receive signals from up to 128 wireless zones, plus 16 wireless keypads. Also supports up to
32 wireless keys or 32 panic pendants and 16 sirens
l Supervisory - programmable supervisory window
l Can be wired up to 1000 ft. / 230 m from the main panel with 22 AWG wire
l Connects to Corbus
l Compatibility: The HSM2HOST is used with PowerSeries Neo alarm panels
l Operating temperature: NA= 0°C – +49°C (32-122°F); EU= -10°C – +55°C
l Relative humidity: 93% non-condensing
l Separate, built-in wall and case tampers
Note: For Commercial BURG (UL) the Supervisory window shall be set to 4 hours.
For Residential Fire (UL/ULC) the Supervisory window shall be set to 200 seconds.
For Residential BURG (UL/ULC) the supervisory window shall be set to 24 hours.
For UL Home Healthcare applications the supervisory window shall be set to 24 hours
Only models operating in the band 912-919 MHz are UL/ULC listed where indicated. Only UL approved
devices are to be used with UL/ULC listed systems.
l
l
3
Compatible Wireless Devices
Compatible Wireless Devices
The HSM2HOSTx (x= 4/8/9) can receive signals from the devices listed in the following chart. Please refer to the
individual device instruction sheet. Throughout this document, x in the model number represents the operating frequency of the device as follows: 9 (912-919 MHz), 8 (868MHz), 4 (433MHz).
Alarm Controllers
PowerSeries Neo alarm controllers
HS2128/HS2128 E/HS2064/
HS2064 E/HS2032/ HS2016
Modules
Wireless keypads
HS2LCDWFx
HS2LCDWFPx
HS2LCDWFPVx
Wireless Devices
Wireless PG smoke detector
PGx926UL
Wireless PG smoke and heat detector
PGx916UL
Wireless PG CO detector
PGx913
Wireless PG PIR motion detector
PGx904(P)UL
Wireless PG PIR + camera motion detector
PGx934(P)UL
Wireless Outdoor PG PIR + camera motion detector
PGx944
Wireless PG curtain motion detector
PGx924UL
Wireless PG dual tech motion detector
PGx984(P)
Wireless PG mirror motion detector
PGx974(P)UL
Wireless PG outdoor motion detector
PGx994UL
Wireless PG glass break detector
PGx912,
PGx922
Wireless PG shock detector
PGx935UL
Wireless PG flood detector
PGx985UL
Wireless PG temperature detector (indoor use)
PGx905UL
Wireless PG key
PGx939UL
Wireless PG key
PGx929UL
Wireless PG panic key
PGx938UL
Wireless PG 2-button key
PGx949UL
Wireless PG indoor siren
PGx901UL
Wireless PG outdoor siren
PGx911UL
Wireless PG repeater
PGx920UL
Wireless PG door/window contact
PGx975UL
Wireless PG door/window contact w/ AUX
PGx945UL
4
HSM2HOST Installation Manual
Safety Instructions
l
l
l
l
This equipment must be installed by Service Persons only (a service person is defined as a person having
the appropriate technical training and experience necessary to be aware of hazards to which that person
may be exposed in performing a task and of measures to minimize the risks to that person or other persons). It must be installed and used within a non-hazardous, indoor environment only (pollution degree
max 2, over voltages category II).
The installer is responsible for instructing the system user in regards to electrical safety precautions when
using a system which includes this equipment and also in regards to each of the following:
l Do not attempt to service this product. There are no user serviceable parts inside. If servicing is
required, it shall be referred to service persons only.
Using adequate mounting means (e.g., plastic/metal anchors), secure the transceiver to the building structure before applying power.
Internal wiring must be routed in a manner that prevents:
l Excessive strain on wire and on terminal connections;
l Loosening of terminal; connections;
l Damage to conductor insulation.
Only UL/ULC listed devices can be used in UL/ULC listed installations.
HSM2HOST9 is listed for UL Commercial Burglary, Residential Fire, Residential Burglary and Home Health
Care, ULC Residential Fire and Residential Burglary:
UL1610 Central-Station Burglar Alarm Units
UL1023 Household Burglar-Alarm System Units
UL985 Household Fire Warning System Units
UL1637 Home Health Care Signaling Equipment
ULC-S545-02 Residential Fire Warning System Control Units
ORD-C1023-1974 Household Burglar-Alarm System Units
UL 609 Local Burglar Alarm Units and Systems
UL365 Police Station Connected Burglar Alarm Units and Systems
5
Introduction
Introduction
The HSM2HOSTx two-way wireless transceiver adds wireless capability to PowerSeries Neo alarm controllers,
model HS2128 E, HS2064 E, HS2032 or HS2016. The HSM2HOST receives signals from wireless zones and wireless keys, and provides information to the alarm controller it is connected to. This manual describes how to install,
program and maintain the HSM2HOST. Note that only one HSM2HOST or one RFK keypad can be enrolled on
the alarm system.
Before installing:
1. Plan the placement and wiring of the security system (see system installation manual).
2. Install the control panel and optional modules.
3. Temporarily mount all wireless devices in the intended location.
Installation Process Overview
To install and set up the HSM2HOST and wireless devices:
1. Temporarily mount and wire the HSM2HOST module ("Mounting" on page 8).
2. Enroll the HSM2HOST and first wireless keypad ("Enroll The HSM2HOST" on page 8).
3. Check the location for RF interference levels ("[804][801] RF Jam Detect" on page 10).
4. Enroll wireless devices ("[804][000] Enroll Wireless Devices" on page 10).
5. Complete zone and other programming on the system ("Wireless Device Setup and Programming" on page
10).
6. Test the placement of all the wireless devices ("[904] Placement Testing Wireless Devices" on page 13).
7. Permanently mount the HSM2HOST and wireless devices ("Permanently Mount" on page 9).
Controls and Indicators
Status LEDs
The LEDs on the front of the HSM2HOST provide feedback regarding the installation, operation and troubleshooting of the unit. The LEDs function as follows:
Red LED
Operation
Module Power Up:
On steady during module power-up sequence then off.
Firmware Update:
Slow flashing = update in progress
Rapid flashing = update failed
Trouble Condition:
l
l
l
l
l
No trouble: 1 rapid flash every 10 seconds.
If troubles are present, a series of flashes occur every 2 seconds. Each series of
flashes indicate troubles as follows:
1 flash: Module not enrolled
2 flashes: Loss of contact with module for over 60 seconds
3 flashes: Corbus low voltage
8 flashes: RF interference (jam condition)
Module Confirmation:
Flashes rapidly during module confirmation process.
Placement Test:
On steady when location is bad. Off when location is good.
Green LED
Placement Test:
Operation
On steady when location is suitable. Off when location is unsuitable.
Note: For UL/ULC listed systems, signal must be “Strong”. See Wireless Device Status
Indications on page 10 for details.
6
HSM2HOST Installation Manual
Tamper
The HSM2HOST has separate built-in wall and case tampers. The case tamper is disabled by default on the NA
version (enabled on EU version).
Section [804][810] option 3 enables or disables the case tamper. Enable or disable the wall tamper by fastening
the breakaway wall tamper bracket securely to the wall using one of the supplied screws.
The case tamper activates when the case is opened and restores when the case is closed. The wall tamper on the
back of the unit is depressed by the mounting surface when properly installed. If the unit is removed, the tamper
activates. Ensure the mounting surface is smooth and free of obstructions that block access to the rear of the unit.
Electrical wires should not run over or under the module when it is mounted.
Note: The built in wall and case tamper must be installed and enabled for UL/ULC listed Commercial/ Residential
Burglary applications.
7
Setup and Wiring
Setup and Wiring
This section describes how to set up and wire the HSM2HOST module.
Mounting
Note: Permanently mount the HSM2HOST receiver and wireless devices AFTER placement testing each device ("
[904] Placement Testing Wireless Devices" on page 13).
Find a place that is:
l dry,
l within operating temperature range,
l central to the proposed placement of all wireless devices,
l as high as possible. The range is reduced if mounted below ground level,
l far from sources of interference, including: electrical noise (computers, televisions, electric motors, appliances, heating and air conditioning units), large metal objects like heating ducts and plumbing which may
shield the electro-magnetic waves,
l smooth and free of obstructions that block access to the rear of the unit.
Connect the HSM2HOST
Caution: Remove all power (AC, DC, telephone lines) from the system while connecting modules to the Corbus.
To connect the HSM2HOST:
1. With the alarm panel powered down, connect the HSM2HOST to the four-wire Corbus of the alarm panel
according to Figure 1.
2. Once the wiring is complete, power up the security system.
Figure: 1 Wiring Diagram
Enroll The HSM2HOST
The HSM2HOST must be enrolled onto the alarm panel before any wireless devices can be enrolled.
When the alarm system is powered up for the first time, the first keypad or the HSM2HOST (if using a wireless
keypad as the first keypad) can be enrolled.
To do this:
1. Once the HSM2HOST is wired to the alarm panel and power has been applied, power up a wireless
keypad.
2. Press any button on the keypad to enroll it on the HSM2HOST. The HSM2HOST is then automatically
enrolled on the alarm panel.
Alternately, enroll the HSM2HOST on the system at any time using the following procedure:
1. Enter Installer Programming section [902][000] (Auto Enroll All Modules). Modules are automatically
detected in the following order:
1– Keypads
2 – Zone Expander
8
HSM2HOST Installation Manual
3 – Output Module
4 – HSM2HOSTx
5 – Audio Verification Module
6 – Power Supply 1A
2. When prompted, press [*] to enroll.
Or another Alternate method,
1. Enter Installer Programming section [902][001] (Enroll Modules).
2. When prompted, key in the serial number found on the back of the module. The module is enrolled.
Delete the HSM2HOST
To remove the HSM2HOST from the system:
1. Enter Installer Programming section [902][106] (Delete HSM2HOSTx).
2. Press [*] to delete.
Permanently Mount
Once a suitable location is found, mount the HSM2HOST as follows:
1. Pull the Corbus wires through the holes at the back of the cabinet.
2. Mount the cabinet securely to the wall using the three screws supplied.
3. To enable the wall tamper, fasten the breakaway wall tamper bracket securely to the wall using the supplied screw.
Figure: 2 Mounting the HSM2HOST
Other Options
The following actions may be performed on the HSM2HOST:
Section
Action
[902][106] Delete the HSM2HOST from the alarm system.
[903][106] Confirm that the HSM2HOST is enrolled.
[000][806] Add a label to appear on LCD keypads.
[900][461] View HSM2HOST model information.
9
Wireless Device Setup and Programming
Wireless Device Setup and Programming
This section describes how to enroll and program wireless devices such as contacts, motion sensors and sirens on
the alarm panel.
[804][000] Enroll Wireless Devices
Once the HSM2HOST is installed and enrolled on the alarm panel, wireless devices can be enrolled using the following method:
1. Enter Installer Programming section [804][000].
2. When prompted, either activate the device (see device installation sheet) to enroll immediately or enter a
device ID number. Do the latter to pre-enroll devices then enroll them later at the customer site. The alarm
panel determines the type of device being enrolled and presents the appropriate programming options.
Wireless Device Options
Device Type Programming Options
3.
4.
5.
6.
7.
Zone
(01) Zone type
(02) Partition assignment
(03) Zone label
Wireless Key
(01) Partition assignment
(02) User label
Siren
(01) Partition assignment
(02) Siren label
Repeater
(01) Repeater label
Use the scroll keys or type in the corresponding number to select an option.
Scroll through the available selections, key in a number or enter text as appropriate.
Press [*] to accept and move to the next option.
Once all options are configured, the system prompts to enroll the next device.
Repeat the process described above until all wireless devices are enrolled.
Note: The configuration options listed above can be modified using [804][911] Modify Device.
[804][001]-[716] Wireless Device Configuration
To configure wireless devices:
1. Enter Installer Programming section [804] then select one of the following sub-sections:
l 001-128 – Configure Wireless Zones
l 551-566 – Configure Wireless Sirens
l 601-632 – Configure Wireless Keys
l 701-716 – Configure Wireless Keypads
2. Select a device to configure using the scroll keys or go directly to a specific device by entering a hotkey.
3. Use the scroll buttons or enter a hotkey to select a configuration option for the device. See device sheets
for details.
4. Press [*] to accept and move to the next option.
5. Once all options are configured, the system returns to the base configuration menu.
6. Repeat the process described above to configure other wireless devices.
[804][801] RF Jam Detect
RF jam detection (continuous interfering transmissions on the radio network) can be turned on or off. When on,
RF jamming is logged and reported.
To configure RF jamming:
10
HSM2HOST Installation Manual
1. Enter Installer Programming section [804][801] then select one of the following options:
00 Disabled
Jamming detection and reporting is enabled/disabled Note: Must be Enabled for
UL/ULC listed installations.
01 UL 20/20-USA
Continuous RF jamming for 20 seconds
02 EN 30/60Europe
30 seconds of accumulated jamming within 60 seconds
03 Class 6 30/60British
As EN (30/60) but reported only if the jamming duration exceeds 5 minutes
2. Press [*] to accept the selection.
3. Press [#] to exit the section.
[804][802] Wireless Supervision Window
This option is used to program the length of time a wireless device can be absent from the system before a fault is
generated.
For EN installations, 1 hour or 2 hours must be selected.
When option 06 is used, which configures the system to generate fault conditions after a device has been detected
as absent for 24 hours, smoke detectors generate a fault condition after a maximum of 18 hours when the 200s
supervision toggle option is disabled.
To program the Wireless Supervisory Window:
1. Enter Installer Programming section [804][802].
2. Select one of the following options by scrolling or entering the hotkey:
l 00 – Disabled
l 01 – After 1 Hour
l 02 – After 2 Hour
l 03 – After 4 Hour
l 04 – After 8 Hours
l 05 – After 12 Hours
l 06 – After 24 Hours
3. Press [*] to accept the selection.
4. Press [#] to exit the section.
Note: For UL Residential Burglary (UL1023), Home Health Care (UL1637), ULC Residential Burglary
(ULC/ORD-C1023) installations, the maximum Supervision window shall be set to 24 hours.
For UL Residential Fire (UL985) installations, the maximum supervision window is set to 200s.
For UL Commercial Burglary (UL1610/UL365) and ULC Residential Fire (ULC-S545), the maximum supervision
window shall be set to 4 hours.
[804][810] Wireless Option 1
To program wireless options:
1. Enter Installer Programming section [804][810].
2. Select one of the following options by scrolling or entering the hotkey:
11
[804][841] Motion Cameras
01
RF Delinquency
On: the system cannot be armed if a wireless supervisory trouble exists. An RF
delinquency trouble is generated.
Off: wireless supervisory troubles do not prevent arming.
02
Wireless
Supervisory/
RF Jam
Alarm
On: if a supervisory or jamming trouble occurs during Away arming, the siren
activates and the event is logged and reported.
Off: supervisory or RF jam troubles during Away arming do not activate the siren
or get logged and reported.
03
Wireless
Tamper
On: module tampers are logged and reported.
Off: module tampers are not logged or reported.
04
Fire Supervision
On: fire devices are supervised every 200 seconds. If the device fails to report
within this window, a supervision trouble is generated.
Off: fire devices follow the supervision window programmed in section 802, up to
a maximum of 18 hours. The supervisory window can be programmed with a
higher value, but detectors still go into fault after 18 hours.
3. Press [*] to accept the selection and [#] to exit.
[804][841] Motion Cameras
To program motion cameras:
1. Enter Installer Programming section [804][841].
2. Select one of the following options by scrolling or entering the hotkey:
[001] Visual Verification
On: Alarms trigger image capture from PIR Cameras
Off: Alarms do not trigger image capture from PIR Cameras
[002] View Time Window 01 Alarm + 5 Minutes
02 Alarm + 15 minutes
03 Alarm + 1 Hour
[003] View Other Alarms
01
02
03
04
Fire key enabled/disabled
Duress enabled/disabled
Medical key enabled/disabled
Panic key enabled/disabled
[804][901]-[905] Delete Wireless Devices
To delete wireless devices:
1. Enter Installer Programming section [804] then select one of the following sub-sections:
[901] – Delete wireless zone devices
[902] – Delete wireless key
[903] – Delete sirens
[904] – Delete repeaters
[905] – Delete keypads
2. Select a device to delete using the scroll keys or go directly to a specific device by entering a hotkey.
3. Press [*] to delete or [#] to exit.
[804][921]-[925] Replace Wireless Devices
Use this option to replace a faulty device enrolled on the system with another device of the same type while
maintaining the configuration of the original. The faulty device does not need to be deleted.
To replace a wireless device:
12
HSM2HOST Installation Manual
1. Enter Installer Programming section [804] then select one of the following sub-sections:
[921] – Replace wireless zone devices
[922] – Replace wireless key
[923] – Replace sirens
[924] – Replace repeaters
[925] – Replace keypads
2. Press [*] to select a sub-section. The first available device is displayed.
3. Select a device to replace using the scroll keys or go to a specific device by entering a hotkey.
4. Press [*]. When prompted, activate the device (full enrollment) or enter the device ID (pre-enrollment). A
message is displayed confirming enrollment.
[804][990][001 – 005] Show All Devices
Use this section to review wireless devices enrolled on the system and to view serial numbers associated with
each device.
To review wireless device information:
1. Enter Installer Programming section [804][990] then select one of the following sub-sections:
l [001] – All zones
l [002] – Repeaters
l [003] – Sirens
l [004] – Wireless keys
l [005] – keypads
2. Press [*] to select a wireless device type. The first available device is displayed.
3. Use the scroll keys to view the enrolled devices.
Note: This option is not fully supported by LED and ICON keypads.
[804][999] Reset to Factory Defaults
Selecting this option resets HSM2HOST programming to factory default settings.
[904] Placement Testing Wireless Devices
This test is used to determine RF signal status for wireless devices and can be performed at a system keypad or at
the individual device. These instructions pertain to testing at the keypad. For instructions on placement testing at
the device, refer to the installation sheet provided with the wireless equipment. The following test modes are available:
[904][001]-[128] Test wireless zones
Test wireless devices individually by zone. Zones with
vanishing contacts must be activated to placement test.
[904][521]-[528] Test all repeaters
Test each enrolled wireless repeater. 521-528 for repeaters 1-8
[904][551]-[566] Test all sirens
Test each enrolled wireless siren. 551-566 for sirens 116
[904][601]-[632] Test all wireless keys Test individual wireless keys. Once in this section,
press a button on the wireless key to begin the test.
601-632 for wireless keys 1-32.
[904][701]-[716] Test all keypads
Test each enrolled keypad. 701-716 for keypads 1-16
Two test results are provided:
l 24-hour: Average results of signal strength testing over a 24-hour period.
l Now: Signal status results of the current test.
A flashing Trouble LED indicates RF interference. The following status indicators may be displayed:
13
[904] Placement Testing Wireless Devices
LCD
Icon* LED+ Status
Strong
1
9
Strong signal strength
Good
2
10
Good signal strength
Poor
3
11
Poor signal strength
Not Test 5
13
Displayed as the Now result if no test was performed
Not Test 5
13
Always displayed as the 24-hour result when testing wireless keys
*For Icon keypads, digit 1 indicates 24-hour test results; digit 2 indicates Now test results.
+For LED keypads, the first digit indicates 24-hour results; the second digit indicates Now test results.
Note: For EN/UL/ULC installations, only STRONG signal levels are acceptable.
14
HSM2HOST Installation Manual
Programming Worksheets
Use these pages for recording custom programming options (Installers Programming: [*][8]).
[902] Enroll Module
000 - Auto Enroll
001 - Enroll Modules
002 - Module Slot Assignment (LED/ICON)
003 - Module Slot Assignment (LED only)
Delete Module
101 - Delete Keypads
102 - Delete Zone Expander
103 - Delete Output Expander
106 - Delete HSM2HOST
108 - Delete Audio Verification
109 - Delete Power Supply
[903] Confirm Module 001 - Confirm Keypad
002 - Confirm Zone Expander
003 - Confirm Output Expander
006 - Confirm HSM2HOST
008 - Confirm Audio Verification
009 - Confirm Power Supply
Label Programming
[000] Module Lables
[801]
Keypad Label (1 x 14 Characters)
001:
009:
002:
010:
003:
011:
004:
012:
005:
013:
006:
014:
007:
015:
008:
016:
15
Label Programming
[802]
Zone Expander Label (1 x 14 Characters)
[803]
001:
009:
002:
010:
003:
011:
004:
012:
005:
013:
006:
014:
007:
015:
008:
016:
Output Expander Label (1 x 14 Characters)
[806]
001:
009:
002:
010:
003:
011:
004:
012:
005:
013:
006:
014:
007:
015:
008:
016:
HSM2HOST Label (1 x 14 Characters)
01:
[809]
HSM2300 Power Supply Label (1 x 14 Characters)
01:
02:
03:
04:
[810]
HSM2204 High-Current Output Label (1 x 14 Characters)
01:
02:
03:
04:
16
HSM2HOST Installation Manual
[820]
Siren Labels (1 x 14 Characters)
01:
02:
03:
04:
05:
06:
07:
08:
[821]
Repeater Labels (1 x 14 Characters)
01:
02:
03:
04:
05:
06:
07:
08:
[804] Wireless Programming
[000]
Enroll Wireless Device
Zone
Wireless Key
Siren
Keypad
Repeater
17
[804][000] Wireless Device Enrollment – Zones
[804][000] Wireless Device Enrollment – Zones
Zone
Zone Definition
Label
18
Zone
Type
Partition
HSM2HOST Installation Manual
[804][000] Wireless Device Enrollment – Wireless Keys
Key# Partition# User
Label
Key# Partition#
1
17
2
18
3
19
4
20
5
21
6
22
7
23
8
24
9
25
10
26
11
27
12
28
13
29
14
30
15
31
16
32
User
Label
[804][000] Wireless Device Enrollment – Wireless Sirens
WLS
Siren#
Partition#
WLS
Partition#
Siren#
Siren Label
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16
19
Siren Label
[804][000] Wireless Device Enrollment – Wireless Keypads
[804][000] Wireless Device Enrollment – Wireless Keypads
WLS
Keypad
Keypad# Assignment
WLS
Keypad
Keypad# Assignment
Keypad Label
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16
Keypad Label
[804][000] Wireless Device Enrollment – Wireless Repeaters
Repeater#
Repeater Label
1
2
3
4
5
6
7
8
20
HSM2HOST Installation Manual
[804][001]-[128] Configure Wireless Zones 1-128 (copy as needed)
Zone#:
Toggle Options
[001] Device Options
[003] High Traffic Shutdown
✓
01 – Alarm LED
✓
02 – Reed Switch
02 – Yes - No Delay
03 – External Input On
03 – Yes - 5s Delay
04 – Supervision
04 – Yes - 15s Delay
05 – Not Used
05 – Yes - 30s Delay
06 – Not Used
06 – Yes - 1m Delay
07 – Not Used
07 – Yes - 10m Delay
08 – Not Used
08 – Yes - 20m Delay
09 – Shock Accumulator
09 – Yes - 15s Delay
10 – Not Used
10 – Yes - 60m Delay
11 – 24hr/Night
[004] Image Brightness
12 – Piezo Siren
01 – Image Bright -3
13 – Not Used
02 – Image Bright -2
14 – Fire Alarm
03 – Image Bright -1
✓
✓
✓
15 – Not Used
✓
✓ 01 – Not Active
✓ 04 – Image Bright 0
16 – Not Used
05 – Image Bright +1
[002] Zone EOL
06 – Image Bright +2
00 – Disable
07 – Image Bright +3
01 – Single EOL
02 – Normally Open
03 – Normally Closed
04 – Double EOL
21
[804][551]-[556] Configure Wireless Sirens 1-16 (copy as needed)
✓
✓
[005] Image Contrast
[016] Event Counter
01 – Image Contrast -3
001-002 (Default: 002)
02 – Image Contrast -2
[011] Camera Toggles
03 – Image Contrast -1
✓
01 – Color
04 – Image Contrast 0
✓
02 – High Res.
05 – Image Contrast +1
03 – Low Quality
06 – Image Contrast +2
04 – Microphone
07 – Image Contrast +3
09 – AC Power
[006] Detection Range
[018] Shock Sensitivity
01 – Low Sensitivity
001-019 (Default: 008)
02 – Mid Sensitivity
[019] High Temp. Warning
03 – High Sensitivity
+/- 000-999 (Default:999c)
[007] Detection Sensitivity
[020] High Temp. Alarm
01 – Low Sensitivity
+/- 000-999 (Default:999c)
02 – Mid Sensitivity
[021] LowTemp. Warning
03 – High Sensitivity
+/- 000-999 (Default:999c)
03 – UL Standard
[019] Low Temp. Alarm
+/- 000-999 (Default:999c)
[804][551]-[556] Configure Wireless Sirens 1-16 (copy as needed)
Zone#
Toggle Options
[000] Partition Assignment
12345678
[001] Device Toggles
[002] Strobe Alarm
[004] Squawk
01 – Disabled
01 – Disabled
✓ 01 – Fire Alarm
✓ 02 – Gas/CO Alarm
✓ 02 – Timer Limited
✓ 02 – Sounder Only
✓ 03 – Burglary Alarm
03 – Until Disarmed
03 – Strobe Only
✓ 04 – Flood Alarm
[003] Exit Entry Beeps
04 – Sounder/Strobe
05 – Not Used
✓ 01 – Disabled
06 – Auto Temp Alarm
02 – Enabled
07 – Activity LED
03 – Disabled Stay
08 – Not Used
[005] Sounder Volume
01 – Low
✓ 02 – Medium
03 – High
09 – AC Power
✓ 10 – Buzzer Notification
✓ 11 – Door Chime
✓ 12 – Trouble Beep
22
HSM2HOST Installation Manual
Zone#
Toggle Options
[000] Partition Assignment
12345678
[001] Device Toggles
[002] Strobe Alarm
[004] Squawk
01 – Disabled
01 – Disabled
✓ 01 – Fire Alarm
✓ 02 – Gas/CO Alarm
✓ 02 – Timer Limited
✓ 02 – Sounder Only
✓ 03 – Burglary Alarm
03 – Until Disarmed
03 – Strobe Only
✓ 04 – Flood Alarm
[003] Exit Entry Beeps
04 – Sounder/Strobe
05 – Not Used
✓ 01 – Disabled
06 – Auto Temp Alarm
02 – Enabled
07 – Activity LED
03 – Disabled Stay
[005] Sounder Volume
01 – Low
✓ 02 – Medium
08 – Not Used
03 – High
09 – AC Power
✓
10 – Buzzer Notification
✓
11 – Door Chime
✓
12 – Trouble Beep
[804][601]-[632] Configure Wireless Keys (copy as needed)
[000] Wireless Key Partition Assignment (Default: 01)
[001]-[005] Wireless Key Button Programming (Defaults: Key 1: 04, Key 2: 03, Key 3: 01, Key 4: 52, Key 5: 21)
[011] Wireless Key Device Toggles (Default: 01)
[020] Wireless Key User Assignment (Default: 00 – Not Assigned)
Available programming options:
00- Disabled (Null)
01- Disarm
02- Instant Stay Arm
03- Stay Arm
04- Away Arm
05- [*][9] No Entry
06- Chime On/Off
07- System Test
09- Night Arm
12- Global Stay Arm
13- Global Away Arm
14- Global Disarm
16- Quick Exit
17- Arm Interior
21- Comm. Output
22- Comm. Output
23- Comm. Output
24- Comm. Output
23
1
2
3
4
29- Bypass Group Recall
33- Bypass Recall
51- [M] Key Alarm
52- [P] Key Alarm
[601]-[632] Wireless Key 1-32
[601]-[632] Wireless Key 1-32
Wireless Key#
Wireless Key#
Wireless Key#
Wireless Key#
Wireless Key#
Partition
Button
12345678
1:
2:
3:
4:
5
Partition
Button
12345678
1:
2:
3:
4:
5
Partition
Button
12345678
1:
2:
3:
4:
5
Partition
Button
12345678
1:
2:
3:
4:
5
Partition
Button
12345678
1:
2:
3:
4:
5
Supervision Yes
No
User Number
✓
Supervision Yes
No
User Number
✓
Supervision Yes
No
User Number
✓
Supervision Yes
No
User Number
✓
Supervision Yes
No
User Number
✓
[804]-[701]-[716] Wireless Keypad Programming (copy as needed)
Keypad#
[000]
00 – Global
03 – Partition 3
03 – Partition 3
✓ 01 – Partition 1
04 – Partition 4
04 – Partition 4
02 – Partition 2
05 – Partition 5
05 – Partition 5
Partition Assignment
Function Key Programming Options:
24
HSM2HOST Installation Manual
00
02
03
04
05
06
07
09
11
12
- Null Key
- Instant Stay Arm
– Stay Arm
- Away Arm
- [*][9]No Entry Arm
- Chime On/Off
- System Test
- Night Arm
- Away Arm no Entry
- Global Stay Arm
Function Key:
13
14
16
17
21
22
23
24
29
30
- Global Away Arm
- Global Disarming
- Quick Exit
- Arm Interior
- Command Output 1
- Command Output 2
- Command Output 3
- Command Output 4
- Bypass Group Recall
- Quick Bypass
31 - Local PGM Active
32 - Bypass Mode
33 - Bypass Recall
34 - User Programming
35 - User Functions
36 - Reactivate
Stay/Away/Night zones
37 - Time/Date Programming
39 - Trouble Display
40 - Alarm Memory
61
62
63
64
65
66
67
68
- Partition
- Partition
- Partition
- Partition
- Partition
- Partition
- Partition
- Partition
[001] – Key 1:
(Default: 03)
[003] – Key 3:
(Default: 06)
[005] – Key 5:
(Default: 16)
[002] – Key 2:
(Default: 04)
[004] – Key 4:
(Default: 22)
[011] Keypad I/O (Zone number or output number; 3-digit decimal; Default: 000)
[012] Local PGM Output Timer:
[021] Keypad Option 1
Pulse Time (Default:00 minutes):
Pulse Time (Default:05 minutes):
✓ 01 – [F] Key Enabled
✓ 02 – [M] Key Enabled
✓ 03 – [P] Key Enabled
✓ 04 – Display Code or X's
[022] Keypad Option 1
✓ 01 – Local Clock Display
02 – Local Clock 24-Hour
✓ 03 – Auto Alarm Scroll
✓ 05 – Power LED
✓ 06 – Power LED AC Present
✓ 07 – Alarms Displayed if Armed
✓ 08 – Auto Scroll Open Zones
[023] Keypad Option 3
01 – Armed LED Power Save
✓ 02 – Keypad Status Shows Arm Mode
03 – 5th Terminal is PGM Output/Zone Input
07 – Local Display of Temperature
08 – Low Temperature Warning
[030] LCD Message:
[031] Downloaded LCD Message Duration (3-digit decimal; 000-255; Default: 000):
[041] Indoor Temperature Zone Entry (3-digit decimal; 000-128; Default: 000):
[042] Outdoor Temperature Zone Entry (3-digit decimal; 000-128; Default: 000):
25
Select
Select
Select
Select
Select
Select
Select
Select
1
2
3
4
5
6
7
8
[804][801] Jam Detect
[101]-[128] Door Chime Beeps:
00 – Disabled
✓
01 – 6 beeps
02 – Bing Bong
03 – Ding Dong
04 – Alarm Tone
05 – Zone Name
Door Chime Zone Assignment:
1 ____
2 ____
3 ____
4 ____
5 ____
6 ____
7 ____
8 ____
9 ____
10 ____
11 ____
12 ____
13 ____
14 ____
15 ____
16 ____
17 ____
18 ____
19 ____
20 ____
21 ____
22 ____
23 ____
24 ____
25 ____
26 ____
27 ____
28 ____
29 ____
30 ____
31 ____
32 ____
33 ____
34 ____
35 ____
36 ____
37 ____
38 ____
39 ____
40 ____
41 ____
42 ____
43 ____
44 ____
45 ____
46 ____
47 ____
48 ____
49 ____
50 ____
51 ____
52 ____
53 ____
54 ____
55 ____
56 ____
57 ____
58 ____
59 ____
60 ____
61 ____
62 ____
63 ____
64 ____
65 ____
66 ____
67 ____
68 ____
69 ____
70 ____
71 ____
72 ____
73 ____
74 ____
75 ____
76 ____
77 ____
78 ____
79 ____
80 ____
81 ____
82 ____
83 ____
84 ____
85 ____
86 ____
87 ____
88 ____
89 ____
90 ____
91 ____
92 ____
93 ____
94 ____
95 ____
96 ____
97 ____
98 ____
99 ____
100 ___
101 ___
102 ___
103 ___
104 ___
105 ___
106 ___
107 ___
108 ___
109 ___
110 ___
111 ___
112 ___
113 ___
114 ___
115 ___
116 ___
117 ___
118 ___
119 ___
120 ___
121 ___
122 ___
123 ___
124 ___
125 ___
126 ___
127 ___
128 ___
[804][801] Jam Detect
[804][802] Supervisory
Window
[804][810] Wireless Options
UL EN
UL
UL EN
EN
Disabled
After 1 Hour
UL – UL 20/20
✓
✓
Disabled
✓
After 2 Hours
1 – RF Delinquency
Tamper
✓
2 – Missing/Jam Alarm
EN 30/60
After 4 Hours
3 – Wireless Tamper
Class 6 (30/60)
After 8 Hours
4 – 200s Fire Supervision
After 12 Hours
✓
After 24 Hours
26
HSM2HOST Installation Manual
[804][841] Motion Cameras
001 Visual Verification
01 – Disabled
✓
02 – Enabled
03 – Enabled
002 View Time Window
✓
01 – Alarm + 5 Minutes
02 – Alarm + 15 Minutes
03 – Alarm + 1 Hour
003 View Other Alarms
✓
01 – Fire Alarm
✓
02 – Duress Alarm
✓
03 – Medical Alarm
✓
04 – Panic Alarm
[804][901]-[905] Delete Wireless Devices
[901] Delete Zones
[902] Delete Wireless Keys
[903] Delete Sirens
[904] Delete Repeaters
[905] Delete Keypads
[804][921]-[925] Replace Wireless Devices
[921] Replace Zones
[922] Replace Wireless Keys
[923] Replace Sirens
[924] Replace Repeaters
[925] Replace Keypads
[804][990] Show All Devices
[001] Show All Zones
[002] Show All Repeaters
[003] Sirens
[004] Wireless Keys
[005] Keypads
27
LIMITED WARRANTY
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of
purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return
of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired parts are
warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty period. There is
absolutely no warranty on software and all software products are sold as a user license under the terms of the
software license agreement included with the product. The Customer assumes all responsibility for the proper
selection, installation, operation and maintenance of any products purchased from DSC. Custom products are
only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit
at its option.
International Warranty
is important that a security system be reviewed periodically to ensure that its features remain effective and that
it be updated or replaced if it is found that it does not provide the protection expected.
Access by Intruders
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by
moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the
proper operation of the system.
Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power
supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if
the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not
have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.
Failure of Replaceable Batteries
The warranty for international customers is the same as for any customer within Canada and the United
States, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or This system’s wireless transmitters have been designed to provide several years of battery life under normal
conditions. The expected battery life is a function of the device environment, usage and type. Ambient conVAT that may be due.
ditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All author- expected battery life. While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will
ized distributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls
keep the system in good operating condition.
must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever
Compromise of Radio Frequency (Wireless) Devices
for which prior authorization has not been obtained.
Signals may not reach the receiver under all circumstances which could include metal objects placed on or
Conditions to Void Warranty
near the radio path or deliberate jamming or other inadvertent radio signal interference.
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:
System Users
l
damage incurredinshippingor handling
l
damage causedbydisaster suchasfire,flood,wind,earthquake or lightning;
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physl
damage due tocausesbeyondthe controlof DigitalSecurityControlssuchasexcessive voltage,mech- ical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important
anicalshock,water damage;
that all system users be trained in the correct operation of the alarm system and that they know how to respond
l
damage causedbyunauthorizedattachment,alterations,modificationsor foreignobjects;
when the system indicates an alarm.
l
damage causedbyperipherals(unlesssuchperipheralswere suppliedbyDigitalSecurityControls
Smoke Detectors
Ltd.);
Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasl
defectscausedbyfailure toprovide a suitable installationenvironmentfor the products;
ons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke
l
damage causedbyuse of the productsfor purposesother thanthose for whichitwasdesigned;
may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the
l
damage from improper maintenance;
l
damage arisingoutof anyother abuse,mishandlingor improper applicationof the products.
other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence
or building.
Items Not Covered by Warranty
Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense
In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i)
freight cost to the repair centre; (ii) products which are not identified with DSC's product label and lot number all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by careor serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance lessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson.
or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warnreplacement under warranty will be credited or replaced at DSC's option. Products not covered by this waring to allow all occupants to escape in time to avoid injury or death.
ranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate
Motion Detectors
shall be provided. No repair work will be performed until a valid purchase order is received from the CusMotion detectors can only detect motion within the designated areas as shown in their respective installation
tomer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not
number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach of war- provide volumetric area protection. They have multiple beams of detection and motion can only be detected in
unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings,
ranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or uninlegal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated tentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other
equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, pur- part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can
chaser’s time, the claims of third parties, including customers, and injury to property. The laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such a jurisdiction apply be reduced when the ambient temperature rises near or above body temperature or if there are intentional or
unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radito any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent
permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, ators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.
Warning Devices
so that the above may not apply to you.
Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if
Disclaimer of Warranties
there is an intervening wall or door. If warning devices are located on a different level of the residence or
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether
premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be
expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose)
interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances,
and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls
neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person.
Telephone Lines
to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada.
If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time.
WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular
Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be
basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disdifficult to detect.
ruption, it is possible for this product to fail to perform as expected.
Insufficient Time
Out of Warranty Repairs
There may be circumstances when the system will operate as intended, yet the occupants will not be protected
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its from the emergency due to their inability to respond to the warnings in a timely manner. If the system is monfactory according to the following conditions. Anyone returning goods to Digital Security Controls must first
itored, the response may not occur in time to protect the occupants or their belongings.
obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which Component Failure
prior authorization has not been obtained.
Although every effort has been made to make this system as reliable as possible, the system may fail to funcProducts which Digital Security Controls determines to be repairable will be repaired and returned. A set fee tion as intended due to the failure of a component.
which Digital Security Controls has predetermined and which may be revised from time to time, will be
Inadequate Testing
charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equi- Most problems that would prevent an alarm system from operating as intended can be found by regular testing
valent product available at that time. The current market price of the replacement product will be charged for and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside
each replacement unit.
the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and
WARNING – READ CAREFULLY
any other operational devices that are part of the system.
Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system.
System Failures
Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an emergency situation.
This system has been carefully designed to be as effective as possible. There are circumstances, however,
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without
involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system
Products and Components is copyrighted and is purchased under the following
of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons.
license terms:
Some but not all of these reasons may be:
l
ThisEnd-User License Agreement(“EULA”) isa legalagreementbetweenYou(the company,individualor
Inadequate Installation
A security system must be installed properly in order to provide adequate protection. Every installation should
entitywhoacquiredthe Software andanyrelatedHardware) andDigitalSecurityControls,a divisionof Tyco
be evaluated by a security professional to ensure that all access points and areas are covered. Locks and
SafetyProductsCanada Ltd.(“DSC”),the manufacturer of the integratedsecuritysystemsandthe developer
latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and
of the software andanyrelatedproductsor components(“HARDWARE”) whichYouacquired.
other building materials must be of sufficient strength and construction to provide the level of protection expec- l If the DSC software product(“SOFTWAREPRODUCT” or “SOFTWARE”) isintendedtobe accompanied
byHARDWARE,andisNOTaccompaniedbynewHARDWARE,Youmaynotuse,copyor installthe
ted. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or
SOFTWAREPRODUCT.The SOFTWAREPRODUCTincludescomputer software,andmayinclude assopolice department is highly recommended if this service is available.
ciatedmedia,printedmaterials,and“online” or electronic documentation.
Criminal Knowledge
l
Anysoftware providedalongwiththe SOFTWAREPRODUCTthatisassociatedwitha separate end-user
This system contains security features which were known to be effective at the time of manufacture. It is poslicense agreementislicensedtoYouunder the termsof thatlicense agreement.
sible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It
l
Byinstalling,copying,downloading,storing,accessingor otherwise usingthe SOFTWAREPRODUCT,You
agree unconditionallytobe boundbythe termsof thisEULA,evenif thisEULAisdeemedtobe a modification
of anypreviousarrangementor contract.If Youdonotagree tothe termsof thisEULA,DSC isunwillingto
license the SOFTWAREPRODUCTtoYou,andYouhave norighttouse it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as
other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the
SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run,
shared or used concurrently on or from different computers, including a workstation, terminal or other digital
electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a
license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have
one copy per license installed at any given time. You may use the back-up copy solely for archival purposes.
Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE
PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer,
decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is
expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure
compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component
parts may not be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the
SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the
SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to
others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the
SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and
this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is
an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply
with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE
PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service
marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including
but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the
accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its
suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and
intellectual property rights in and to the content which may be accessed through use of the SOFTWARE
PRODUCT are the property of the respective content owner and may be protected by applicable copyright or
other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not
expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE
PRODUCT to any country, person, or entity subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario,
Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and
binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s
decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC
DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT
OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by
changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the
SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY
EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS
LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY
YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00).
BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY
AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR
IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART
OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES
ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE
THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY
CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES
SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT
DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE
NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY
ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT
EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF
THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for
this SOFTWARE PRODUCT to fail to perform as expected.
FCC Compliance Statement
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the
manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply
with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Re-orient the receiving antenna
- Relocate the alarm control with respect to the receiver
- Move the alarm control away from the receiver
- Connect the alarm control into a different outlet so the alarm control & receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user
may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
+HUHE\ '6& GHFODUHV WKDW WKLV GHYLFH LV LQ FRPSOLDQFH ZLWK WKH HVVHQWLDO
aux appareils radio exempts de licence. L'exploitation est autorisée aux
UHTXLUHPHQWVDQGRWKHUUHOHYDQWSURYLVLRQVRI'LUHFWLYH(&
7KH FRPSOHWH 577( 'HFODUDWLRQ RI &RQIRUPLW\ FDQ EH IRXQG DW
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouilKWWSZZZGVFFRPOLVWLQJVBLQGH[DVS[
&=( '6& MDNR Y¿UREFH SURKODģXMH ŀH WHQWR Y¿UREHN MH Y VRXODGX VH YģHPL
lage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiUHOHYDQWQ¯PLSRŀDGDYN\VPÝUQLFH(&
'$1'6&HUNO¨UHUKHUYHGDWGHQQHNRPSRQHQWHQRYHUKROGHUDOOHYLNWLJHNUDYVDPW
oélectrique subi, même si le brouillage est susceptible d'en compromettre
DQGUHEHVWHPPHOVHUJLWWLGLUHNWLY(&
'87 +LHUELM YHUNODDUW '6& GDW GLW WRHVWHO LQ RYHUHHQVWHPPLQJ LV PHW GH HLVHQ HQ
le fonctionnement.
EHSDOLQJHQYDQULFKWOLMQ(&
),1'6&YDNXXWWDDODLWWHHQW¦\WW¦Y¦QGLUHNWLLYLQ(&ROHQQDLVHWYDDWLPXNVHW
This Class B digital apparatus meets all requirements of the Canadian
)5( 3DU OD SU«VHQWH '6& G«FODUH TXH FH GLVSRVLWLI HVW FRQIRUPH DX[ H[LJHQFHV
HVVHQWLHOOHVHWDXWUHVVWLSXODWLRQVSHUWLQHQWHVGHOD'LUHFWLYH(&
interference-causing equipment regulations.
*(5+LHUGXUFKHUNO¦UW'6&GD¡GLHVHV*HU¦WGHQHUIRUGHUOLFKHQ%HGLQJXQJHQXQG
Cet appareil numérique de la Classe B respecte toutes les exigences de
9RUUDXVHW]XQJHQGHU5LFKWOLQLH(&HQWVSULFKW
*5(˂˜˞˱ˬ˲˭˞ˮ˹˪˱ˬ˯ˤ'6&ˡˤ˨˻˪ˢ˦˹˱˦˞˲˱˛ˤ˰˲˰˧ˢ˲˛ˢ˜˪˞˦˰˺˩˳˶˪ˤ˩ˢ˱˦˯
règlement sur le matériel brouilleur du Canada.
ˬ˲˰˦˻ˡˤ˯˞˭˞˦˱˛˰ˢ˦˯˧˞˦˩ˢ˹˨ˢ˯˱˦˯˙˨˨ˢ˯˰˴ˢ˱˦˧˚˯˞˪˞˳ˬˮ˚˯˱ˤ˯ˍˡˤˠ˜˞˯(&
,7$ &RQ OD SUHVHQWH OD 'LJLWDO 6HFXULW\ &RQWUROV GLFKLDUD FKH TXHVWR SURGRWWR ª
IC:160A-HS2HOST9.
FRQIRUPH DL UHTXLVLWL HVVHQ]LDOL HG DOWUH GLVSRVL]LRQL ULOHYDQWL UHODWLYH DOOD 'LUHWWLYD
&(
The term ‘IC:’ before the radio certification number only signifies that
125'6&HUNO¨UHUDWGHQQHHQKHWHQHULVDPVYDUPHGGHJUXQQOHJJHQGHNUDYRJ
ºYULJHUHOHYDQWHNUDYLGLUHNWLY()
Industry Canada technical specifications were met.
32/'6&RĝZLDGF]DľHXU]ÇG]HQLHMHVWZ]JRGQRĝFL]]DVDGQLF]\PLZ\PDJDQLDPL
RUD]SR]RVWDĄ\PLVWRVRZQ\PLSRVWDQRZLHQLDPL'\UHNW\Z\:(
3253RUHVWHPHLRD'6&GHFODUDTXHHVWHHTXLSDPHQWRHVW£HPFRQIRUPLGDGH
FRP RV UHTXLVLWRV HVVHQFLDLV H RXWUDV GHWHUPLQD©·HV UHOHYDQWHV GD 'LUHFWLYD
(&
63$3RUODSUHVHQWH'6&GHFODUDTXHHVWHHTXLSRHVW£HQFRQIRUPLGDGFRQORV
UHTXLVLWRVHVHQFLDOHV\RWURVUHTXLVLWRVUHOHYDQWHVGHOD'LUHFWLYD(&
6:('6&EHNU¦IWDUK¦UPHGDWWGHQQDDSSDUDWXSSI\OOHUGHY¦VHQWOLJDNUDYHQRFK
DQGUDUHOHYDQWDEHVW¦PPHOVHUL'LUHNWLYHW(&
EU Compliance Statement
The Model HSM2HOST8 Wireless Transceiver has been certified by Telefication according to EN50131-1:2006 + A1:2009 and EN50131-3:2009,
for Grade 2, Class II.
Note: For EN50131 compliant installations only, the intrusion portion of
the alarm system has been investigated. Fire Alarm and Auxiliary (Medical) Alarm functions were not included in the evaluation
of this product under the requirements of the above mentioned standards.
© 2015 Tyco Security Products. All Rights Reserved. www.dsc.com
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any
misuse of the trademarks is strictly prohibited and Tyco will aggressively enforce its intellectual property rights to the fullest
extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco are the property of their respective owners, and are used with permission or allowed under applicable laws. Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features.
Availability varies by region; contact your sales representative.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising