dual zone wine chiller
BEVERAGE MERCHANDISER
Model No.: SCR1505
Instruction Manual
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.
Write Serial No. (on back of unit) here:
________________________________
Felix Storch, Inc.
770 Garrison Avenue
Bronx, NY 10474
www.summitappliance.com
TABLE OF CONTENTS
Appliance Safety .........................................................................
3
Important Safeguards ................................................................
3-4
Special Cautions .........................................................................
5
Location of Parts ........................................................................
6
Handling & Transport .................................................................
6
Unit Review & Inspection ...........................................................
5
Installation Instructions .............................................................
7-9
Location ..................................................................................
7
Installing Shelves ....................................................................
8
Electrical System ....................................................................
8-9
Refrigeration & Lighting System ...............................................
9 - 10
Temperature Control ..............................................................
10
Lighting ...................................................................................
10
User Maintenance .......................................................................
10 - 11
Cabinet Cleaning ....................................................................
10
Condenser Cleaning ...............................................................
10
Cleaning the Compressor/Fan Compartment .........................
11
Defrosting ...............................................................................
11
Security Lock ..........................................................................
11
Energy Saving Tips ................................................................
11
Troubleshooting .........................................................................
12
Limited Warranty ........................................................................
13 - 14
2
APPLIANCE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the Safety Alert Symbol. The symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the words "DANGER" or "WARNING".
Danger means that failure to heed this safety
statement may result in severe personal injury or
death.
Warning means that failure to heed this safety
statement may result in extensive product
damage, serious personal injury, or death.
All safety messages will alert you about the potential hazard, tell you how to reduce the chance of injury,
and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUARDS
Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precautions,
including the following:

Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do
not use an extension cord.

Replace all panels before operating.

It is recommended that a separate circuit serving only your appliance be provided. Use receptacles
that cannot be turned off by a switch or pull chain.

Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion.
And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. The fumes can create a fire hazard or explosion.

Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is
disconnected.
3

Do not connect or disconnect the electric plug when your hands are wet.

Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in
electrical shock or death.

Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

Use two or more people to move and install appliance. Failure to do so can result in back or other
injury.

To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.
Choose a well-ventilated area with temperatures above 60°F (16°C) and below 80.6°F (27°C). This
unit must be installed in an area protected from the elements, such as wind, rain, water spray or drips.

The appliance should not be located next to ovens, grills or other sources of high heat.

The appliance must be installed with all electrical, water and drain connections in accordance with
state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances, is required.

Do not kink or pinch the power supply cord of the appliance.

The size of the fuse (or circuit breaker) should be 15 amperes.

It is important that the appliance be leveled in order to work properly. You may need to make several
adjustments to level it.

All installations must be in accordance with local plumbing code requirements.

Make certain that the pipes are not pinched, kinked or damaged during installation.

Check for leaks after connection.

Never allow children to operate, play with or crawl inside the appliance.

Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage
or discolor the interior.

Use this appliance only for its intended purpose as described in this Instruction Manual.

Keep fingers out of the “pinch point” areas. Clearances between the door and cabinet are necessarily
small. Be careful closing doors when children are in the area.
Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are
still dangerous, even if they will “just sit in the garage a few days”.
Before discarding your old refrigerator:
 Take off the doors
 Leave the shelves in place so that children may not easily climb inside.
- SAVE THESE INSTRUCTIONS 4
SPECIAL CAUTIONS

DO NOT step on the front louver panel of your unit or use it as a step.

ONLY use polarized plugs to plug in your unit.

DO NOT CUT OR REMOVE the ground connection on the electrical cable.

CHECK that the electrical system is grounded BEFORE plugging in refrigerator for the first time.

The polyurethane in your unit contains cyclopentane gas as a foaming agent. When repairing, DO
NOT use other types of polyurethane or mix the existing polyurethane with other types. SUMMIT is
not responsible for changes in the refrigerator if repairs are made by the user or unauthorized
technicians. Contact an authorized distributor for repair information.

DO NOT place hands or other objects in the front louvers, rear grating or the fan guard while in
operation. This can cause personal injury and/or damage unit.

BEFORE removing the front louver panel for maintenance and cleaning, DISCONNECT the unit’s
power supply to avoid accidents which may be caused by the oscillation of the blade of the fan motor.

KEEP HANDS AWAY from door pivot when door is open.

Before loading refrigerator, CHECK that shelves are fixed and have the number of supports indicated
for your model in the Instruction Manual.

CHECK that the front louver panel and rear grating are in place before plugging in unit.

DO NOT place chemical substances (solvents, reagents) or food in this refrigerator. This equipment
is intended for the storage and display of non-potentially hazardous bottled or canned products only.

This equipment is intended to be located in the CONSUMER shopping areas of a retail FOOD store,
if the floor under the unit is maintained clean.

DO NOT balance or tip unit at more than a 45° angle without the supervision of authorized personnel.
Severe injury can occur.

DO NOT try to repair unit by yourself. Always consult your authorized distributor for service.

BEFORE reporting a problem with your SUMMIT refrigerator, check the plug and fuses or circuit
breaker. If this is not the cause of the problem, call your distributor immediately so a technician can
be sent.

The unit’s cooling capacity will decrease if:
– It is open for long periods,
– Excessive amounts of product are stored in it.
THIS WILL OVERLOAD UNIT AND INCREASE MALFUNCTION RISK.
5
LOCATION OF PARTS
Lighted header
Light switch
Internal fan
Interior lighting
(around door)
Adjustable shelves (4)
Handle
Security lock
Glass door
Static condenser
(on back of unit)
Ventilation louvers
Thermostat control
Compressor and fan
(behind louvers)
Leveling legs
HANDLING & TRANSPORT
DO NOT MOVE UNIT WITH PRODUCT INSIDE as loose product can break, spill, damage the appliance,
etc.
WHEN HANDLING STATIC CONDENSER
MODELS SUCH AS THIS, MAKE SURE
THAT DOOR PIVOT IS LOCATED AS
SHOWN IN FIGURE ABOVE.
DO NOT TIP UNIT AT MORE THAN A 45°
ANGLE. DO NOT EXPOSE TO SUNLIGHT
OR STORE AT TEMPERATURES
HIGHER THAN 131°F (55°C).
6
UNIT REVIEW & INSPECTION
This refrigerator was completely inspected before leaving the factory. Check for signs of damage
when the unit is received. If there is any damage, contact your authorized distributor or manufacturer
immediately. Check that the following accessories are included with your refrigerator:

4 wire shelves (packed in plastic wrap inside unit cabinet)

16 shelf clips (packed separately in a plastic bag inside the cabinet)
INSTALLATION INSTRUCTIONS
This model is designed for interior use at a maximum operation temperature of 80.6°F (27°C) and 55%
humidity. It is meant to be free-standing and not built into an enclosure.
Do not place the unit near heat sources such as stoves, grills, radiators, etc. and do not place in areas
where direct sunlight may reach the unit.
CAUTION: This appliance is designed for storing and cooling beverages
and drinks. Do not store perishable food, medicine or other medical
products.
LOCATION
It is recommended that the rear portion and both sides of your refrigerator be at least 8 inches and 6
inches from the wall respectively, to allow air flow to the compressor and improve heat transfer.
Place your refrigerator on a level surface.
Minimum Distances
Once the unit is installed, check that it is level. If necessary, use the two front legs to adjust the height of
the unit.
7
INSTALLING SHELVES
Your refrigerator contains 4 wire shelves and 16 shelf clips.
To install shelves, first place the shelf clips in the slots in the pilasters in the cabinet interior. Use the
numbers on the pilasters as a guide in placing the clips at the same distance from the cabinet floor, with
the tab pointing up as shown. Once all clips are in place, install the shelves by placing them on the clips,
with the outside bar of the shelf on the inside of the clip tabs. Keep all product inside the limits of the
shelves. These allow airflow and should not be blocked when product is stocked in the unit.
CAUTION: DO NOT STOCK PRODUCT UNTIL SHELVES ARE
CORRECTLY INSTALLED IN THE UNIT WITH SHELF CLIPS.
IMPORTANT: TO AVOID ACCIDENTS WHEN CLEANING INSIDE
OF UNIT, FIRST REMOVE SHELVES AND SHELF CLIPS.
ELECTRICAL SYSTEM
Proper electrical installation is required for your refrigerator to function correctly and to prolong the useful
life of electrical parts and compressor.
BEFORE CONNECTING UNIT FOR FIRST TIME:
Verify that line voltage does not fluctuate more than
10% above the nominal value of 115 V, 60 Hz.
DO NOT use extension cords.
DO NOT connect refrigerator to multiple plugs or
plugs with another appliance connected.
The unit MUST be plugged into a grounded socket.
IMPORTANT:
 Do not try to repair any portion of the electrical system yourself. Contact the nearest



authorized service center.
The unit must be grounded.
Ignoring any of the precautions in this manual invalidates the Warranty.
The unit must be connected to a circuit breaker with a 15-ampere fuse and installed
with a minimum 14-caliber wire.
8
Wiring Diagram for model SCR1505:
REFRIGERATION & LIGHTING SYSTEM
The compressor in your SUMMIT refrigerator is designed to function silently. DO NOT plug in the unit
immediately after moving it or changing its position. Allow a minimum of 1 hour for the pressures inside
the refrigeration system to equalize and the oils in the compressor to settle. After plugging the unit in, let
it run for one more hour without load or product. The refrigerator may then be loaded.
DO NOT TOUCH THE COMPRESSOR TOP COVER
while unit is running. It is designed for high
operational temperatures and its surface can
become very hot, which may cause burns. (The
compressor is located at the bottom of the
refrigerator, behind the front louvers.)
9
TEMPERATURE CONTROL
The temperature is controlled by a thermostat which is located on the left side of the ventilation louvers,
below the door. The thermostat has been factory-set to keep the product between 37.4 and 44.6°F (3
and 7°C). At night, or during long periods of inactivity, the appliance goes into an energy-saving mode,
which keeps the temperature between 42.8 and 50.0°F (6 to 10°C).
If it is necessary to readjust the thermostat, please call our toll-free Customer Service number at 800-9324267 between 9:00 AM and 5:00 PM Eastern time.
LIGHTING
Cabinet lighting is designed to function continuously or may be controlled with a switch, located inside the
unit to the left of the internal fan in the ceiling. See Wiring Diagram on page 8. Fluorescent lighting
surrounds the glass on the interior side of the door. Additionally, the header panel above the door is
backlit.
NOTE:
 If the unit is unplugged, or power is lost or turned off, you must wait 3 to 5 minutes before
restarting the unit. If you attempt to restart before this time delay, the unit will not start.
 When you use the unit for the first time or restart the unit after it has been shut off for a long
time, allow a few hours for the interior temperature to normalize.
USER MAINTENANCE
For better performance and user convenience, this refrigerator has been designed to function with the
least possible maintenance and to provide optimal energy consumption and serviceability. It is
recommended, however, that the unit be kept clean and that the following preventative maintenance be
performed.
CABINET CLEANING
 Turn off the power, unplug the appliance, and remove all items, including shelves and shelf clips.
 Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of
baking soda to a quart of water). Once the cabinet interior is clean, dry it with a clean, dry cloth.
 Wash the shelves with a mild detergent solution, then dry them.
 Wring excess water out of the sponge or cloth when cleaning the area where the controls are located,
or any electrical parts.
 Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a
clean soft cloth.
 Do not use steel wool or a steel brush on stainless steel.
NOTE: Do not use alcohol derivatives or thinner to clean the cabinet.
CAUTION: Failure to unplug the appliance during cleaning could result in
electrical shock or other personal injury.
CONDENSER CLEANING
Disconnect the refrigerator's power supply before cleaning. The static condenser (on back of unit) should
be cleaned every 12 months for optimum performance. Use a soft-bristle brush to remove excess dust to
improve heat transfer to the surrounding air.
10
CLEANING THE COMPRESSOR / FAN COMPARTMENT
The compressor and fan are located behind the front louvers of the appliance.
DISCONNECT THE UNIT’S POWER SUPPLY BEFORE
REMOVING THE FRONT LOUVER to avoid accidents that
may be caused by oscillation of the blade of the fan motor.
Door
Front louvers
Compressor
Screws
Fan
To clean the compartment behind the front louvers,
1. Disconnect the power supply to the appliance.
2. Remove the two screws, as shown above.
3. Lift the front louver panel, then pull it toward you, being careful not to disconnect any attached wiring.
4. Clean the area with a damp cloth, then dry it.
5. Replace the louver panel and screw it back into place.
6. Reconnect power to the appliance.
DEFROSTING
It is not necessary to defrost your refrigerator. This is done automatically, using a forced-air system.
There is a defrost water evaporation pan in the compartment below the main cabinet. A hot gas line from
the compressor passes through this pan and evaporates the water. Check occasionally that the drain
hose is always inside the evaporation pan.
SECURITY LOCK
Your unit is provided with a lock and key combination. The lock may be found on the door frame, just
below the door handle. The keys are located inside the plastic bag that contains the Instruction Manual.
After a key has been used, remove it and put it in a secure place for safekeeping.
ENERGY SAVING TIPS
 DO NOT DISCONNECT UNIT AT NIGHT. Reconnecting next day will increase energy consumption.
 DO NOT keep the door open any longer than necessary.
 DO NOT OVERLOAD UNIT. Allow free air flow inside refrigerator.
 DO NOT PLACE HEAVY AND/OR LARGE OBJECTS INSIDE UNIT.
 It is important not to block air flow inside the refrigerator. Remember that it is designed exclusively for
cooling bottles and cans.
 The appliance should be located in the coolest area of the room, away from heat-producing
appliances and out of direct sunlight.
 Ensure that the unit is adequately ventilated. Never cover air vents.
 DO NOT PLACE FOODS IN REFRIGERATOR. The forced air system will absorb their moisture.
11
TROUBLESHOOTING
You can solve many common problems easily, saving you the cost of a possible service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.
Troubleshooting Guide
PROBLEM
The unit does not operate.
The unit is not cold enough.
Turns on and off frequently.
The light does not work.
Ice forms on evaporator.
Vibrations
The unit seems to make too much noise.
The door will not close properly.
Excessive condensation in interior and on door.
POSSIBLE CAUSE
Not plugged in.
Voltage is outside specifications.
Tripped circuit breaker or blown fuse.
Voltage is outside specifications.
Interior air flow is blocked.
There is a nearby heat source.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Condenser needs cleaning.
There is a nearby heat source.
Interior air flow is blocked.
A large amount of product has been added to the
beverage merchandiser.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Condenser needs cleaning.
Not plugged in.
Tripped circuit breaker or blown fuse.
The light switch is OFF.
High relative humidity in environment.
The door is not closed properly.
The door is opened too often or for too long.
Interior air flow is blocked.
Appliance is not level.
Fan blades are out of balance.
Tubes or moving parts are grazing metallic parts.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in the unit.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
The appliance is not level.
The appliance is not level.
The gasket is dirty.
The shelves are out of position.
High relative humidity in environment.
The door is not closed properly.
The door is opened too often or for too long.
12
LIMITED WARRANTY
PARTS AND LABOR WARRANTY INFORMATION
SUMMIT Appliances are manufactured to provide outstanding value, and your satisfaction is our goal on every
product. All SUMMIT major appliances carry a one year limited warranty on both parts and labor. All
refrigerators and freezers carry an additional four years on the compressor. Certain exclusions may apply.
Certain models (including SUMMIT ranges, wall ovens, and cook tops) are manufactured for us in the U.S. and
carry the manufacturer's warranty (also one year parts and on-site labor).
For details on specific warranty issues, please refer to the warranty packed with the product, or contact us.
GENERAL PARTS AND LABOR WARRANTY
SUMMIT warrants, to the original purchaser of every new unit, the cabinet and all parts thereof, to be free
from defects in material or workmanship, under normal and proper use and maintenance service as
specified by SUMMIT and upon proper installation and start-up in accordance with the instruction packet
supplied with each SUMMIT unit. SUMMIT’s obligation under this warranty is limited to a period of 12
months from the date of original purchase.
Any parts covered under this warranty that are determined by SUMMIT to have been defective, within the
above said period, are limited to the repair or replacement, including labor charges, of defective parts or
assemblies. The labor warranty shall include pre-approved standard straight time labor charges only and
reasonable travel time, as determined by SUMMIT.
COMPRESSOR WARRANTY
In addition to the warranty period stated above, SUMMIT warrants its hermetically sealed compressor to
be free from defects in both material and workmanship, under normal and proper use and maintenance,
for a period of 60 months from the date of original purchase. Compressors determined by SUMMIT to
have been defective within this extended time period will, at SUMMIT’s option, be either repaired or
replaced with a compressor or compressor parts of similar design and capacity. The above said
extended compressor warranty applies only to hermetically sealed parts of the compressor and DOES
NOT apply to any other parts or components, including, but not limited to, cabinet, paint finish,
temperature control, refrigerant, metering device, driers, motor starting equipment, fan assembly, or any
other electrical component, etc.
WARRANTY CLAIMS
All claims for labor or parts must be made directly through SUMMIT. All claims should include: model
number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all
pertinent information supporting the existence of the alleged defect. In case of compressor warranty, the
compressor model tag must be returned to SUMMIT along with the above listed information. All claims
should be filed within 30 days of completed repair or the warranty claim could be refused.
THINGS NOT COVERED BY THIS WARRANTY
SUMMIT’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to
the additional limitations below. This warranty neither assumes nor authorizes any person to assume
obligations other than those expressly covered by this warranty.

NO CONSEQUENTIAL DAMAGES: SUMMIT is not responsible for economic loss; profit loss; or
special, direct, indirect, or consequential damages, including without limitation, losses or damages
arising from food or product spoilage claims whether or not on account of refrigeration failure.

WARRANTY IS NOT TRANSFERRABLE: This warranty is not assignable and applies only in favor of
the original purchaser/user to whom delivered. Any such assignment or transfer shall void the
warranties herein made and shall void all warranties, express or implied, including any warranty of
merchantability or fitness for a particular purpose.
13

IMPROPER USE: SUMMIT assumes no liability for parts or labor coverage for component failure or
other damages resulting from improper usage or installation or failure to clean and/or maintain product
as set forth in the warranty packet provided with the unit.

ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR
INSTALLATION, FIRE, FLOOD, ACTS OF GOD: SUMMIT is not responsible for the repair or
replacement of any parts that SUMMIT determines have been subjected after the date of manufacture
to alteration, neglect, abuse, misuse, accident, damage during transit or installation, fire, flood, or act
of God.

IMPROPER ELECTRICAL CONNECTIONS: SUMMIT is not responsible for the repair or replacement
of failed or damaged components resulting from electrical power failure, the use of extension cords,
low voltage, or voltage drops to the unit.

NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE: There are no other warranties, expressed, implied or statutory, except the parts & labor
warranty and the extended compressor warranty specifically described above. These warranties are
exclusive and in lieu of all other warranties, including implied warranty and merchantability or fitness
for a particular purpose. There are no other warranties which extend beyond the description on the
face hereof.

OUTSIDE CONTIGUOUS UNITED STATES: This warranty does not apply to, and SUMMIT is
not responsible for, any warranty claims made on products sold or used outside the Contiguous
(48) United States. To be clear, this warranty excludes the states of Alaska and Hawaii and all
off-shore territories.
REQUESTING SERVICE
If you are in need of service, please either fill out a service request on our website,
http://www.summitappliance.com/support, or call us at 800-932-4267 or 718-893-3900. Please be prepared to
give us the following information: your name, address, phone, email, model, serial, date of purchase, place of
purchase, and the problem you are having.
WARNING! This product may contain chemicals known to the state of California
to cause cancer or birth defects or other reproductive harm. For more information,
visit: www.summitappliance.com/prop65
Chemicals known by the manufacturer to be present in this product in concentrations
higher than threshold limits: NONE.
14
Printed in Mexico
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising