6-Hole Luggage Rack Installation 600764_1

6-Hole Luggage Rack Installation 600764_1
INSTRUCTION SHEET
Part Number
600-764
600-768
Application: 1968-1977 Corvette
Corvette 6-Hole Luggage Rack
Tools Needed
1/2”
Part Includes
1 - Rack Assembly
6 - Screw (1/4 - 20 x 2.62)
6 - Metal Sleeve
6 - Metal Retainer
6 - Rubber Sealing Nut (1/4 - 20 x 1.05)
6 - Rubber Washer
8 - Tips
allation Instructions for Product Number:
1977 Corvette Luggage Rack Hardware Kit
DIAGRAM 1
VIEW
A.
2
FW
D
3
1
5
4
6
DECK LID
CAUTION
Drill must penetrate
fiberglass body panels
only. Fuel Tank is
directly below.
1/2 Dia. Hole
1. Carrier Assembly
2. Screw (1/4 - 20 x 2.62)
3. Metal Sleeve
4. Metal Retainer
5. Rubber Washer
6. Rubber Sealing Nut (1/4 - 20 x 1.05)
Note: Items 1 through 6 should be
pre-assembled before installation
to vehicle.
VERY IMPORTANT:
The optional luggage carrier is designed to offer an alternate storage location on the rear deck of your Corvette. However,
offer an alternate storage location on the rear deck of your Corvette. However,
use of
thiscapacity
rack does
not increase
vehicletoload
specified on the tire placard affixed to the left
maximumthe
vehicle
load
specified
on thethe
tiremaximum
placard affixed
the capacity
left
door
of your
vehicle.
CAUTION:
To help
avoid personal
the vehicle occupants or structual damage to the vehicle
d pessonal
injury
to the
vehicle
occupants
or structural
damageinjury
to thetovehicle
. the loadinon
luggage
should
not exceed
thethe
event
of ancarrier
accident
or sudden
stop,50
thepounds.
load on the luggage carrier should not exceed 50 pounds.
CAUTION
Extreme care must be taken
to insure that rails are equal
MAMotorworks distance from peak lines as
indicated both17082
sides. N.
ThisUS
will
Hw y 45, P.O. Box 1368, Ef fingham, IL 62401
is centered • Worldwide: 217.540.4200 • FAX: 217.540.4800
800.500.1500
Midamotorworksassure fuel filler
between rack w
rails.
w w.mamotor works.com • mail@mamotor works.com
blog.autotainment.com
1
A
©Mid America Motorworks, Inc. All rights reserved.
CARRIER ASSEMBLY
Note: Use as a template
INSTRUCTION SHEET
Part Number
Page 2
Corvette 6-Hole Luggage Rack (cont.)
600-764
600-768
DIAGRAM 2
INSTRUCTIONS:
STEP 1.
Read through all directions and study the diagrams before beginning.
STEP 2.
Use masking tape and run a straight line across the width of the rear deck to mark the rear mounting position.
This line should be 4 1/8” from rear bumper line (1974-1977) or 4 1/8” from lowest spot of spoiler (1968-1973).
This will be the centerline of the rear mounting holes.
STEP 3.
Lay paper on the rear deck and tape in place to protect paint. Position the rack and use as a template for hole location.
Mark through mounting holes with long pencil or pen. Double check all marks.
NOTE: Make sure the gas door does not hit side rails of rack when opening.
STEP 4.
Carefully remove rack, making sure not to move your marks. Assemble all hardware on the rack as in diagram 1.
STEP 5.
USE EXTREME CAUTION! GAS TANK IS 1 1/2” BELOW FIBERGLASS. USE A DEPTH GAUGE ON DRILL BIT. Drill holes at each
marked position.
STEP 6.
Remove masking tape and paper template from the rear deck. Position rack assembly on the rear deck.
STEP 7.
Insert rubber grommets in the holes and tighten each bolt a little at a time. Adjust rack as you go. Don’t over tighten.
MANUFACTURER’S RECOMMENDATION
In order to maintain a long life as well as a lustrous finish to your luggage rack, we recommend applying a coat of polish
or wax of your choice every ninety days to your rack. This will extend the life of the finish and also maintain that show
quality shine. Limited 90 day warranty on workmanship and material.
Toll Free: 800.500.1500
•
Worldwide: 217.540.4200
•
www.mamotorworks.com
•
mail@mamotorworks.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising