Untitled - ClubSound
ENGLISH
OPERATION MANUAL
OPERATION MANUAL
Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
 This compact, stylish 15W WHITE single beam projector is equipped with a very narrow 4° lens making it a
very powerful tool for all kinds of applications: perfect for all kinds of effects on stage but also for simply
illuminating mirror balls etc.
 Thanks to the included 10° & 45° filters this beauty can also be used for discotheques, exhibition booths,
restaurants, shops, … (perfect to light up small objects and small tables)
 Natural white 4500K (or warm white 3200K) color temperature with high CRI-factor (>90).
 Two different DMX-modes: 1 + 2 channels.
 RDM-functionality for easy remote setup: DMX addressing, channel mode, …
 The OLED-display assures easy navigation in the different setup menus.
 TV-Studio ready: no cooling fans and flicker free 1200Hz LED refresh rate.
 Selectable lamp behavior: halogen lamp (slow) or led (fast)
 Four dimmer curves: linear, square, inverse square, S-curve
 In case of DMX failure you can choose between blackout and freeze mode.
 Lock function to avoid unwanted altering of the settings.
 Default factory settings + user settings can be saved/loaded.
 3pin DMX in/outputs and Neutrik® PowerCON® in/outputs for easy daisy chaining.
BEFORE USE
 Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
 English operating instructions, other languages can be downloaded from our website.
 BEAMSPOT1-DMX NW (WW)
 PowerCON mains cable
BRITEQ®
1/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove
the top cover. No user-serviceable parts inside. Refer servicing
to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 1 meters
CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.
 To protect the environment, please try to recycle the packing material as much as possible.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
 This unit is for indoor use only.
 Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
 Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
 Don’t cover any ventilation openings as this may result in overheating.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Allow the device about 10 minutes to cool down before to start servicing.
 Always unplug the unit when it is not used for a longer time or before to start servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the unit.
 The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
 Never let the power-cord come into contact with other cables!
 This fixture must be earthed in order to comply with safety regulations.
 Don’t connect the unit to any dimmer pack.
 Always use an appropriate and certified safety cable when installing the unit.
 In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 The housing and the lenses must be replaced if they are visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
BRITEQ®
2/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
DESCRIPTION:
1. MAINS INPUT: equipped with original Neutrik PowerCON®. Connect the supplied mains cable or any
PowerCon® extension cable here.
2. MAINS OUTPUT: used to daisy chain the power to several other projectors. Always pay attention to the
maximum load while adding projectors! Special Multi cables (PowerCON® + DMX XLR-cables are
optionally available: see our website!)
3. DMX IN: used to daisy chain the projector with other units that will be controlled by a DMX-controller. The
DMX-input is also used to update the firmware of the projector, see the upgrade instructions on our
website.
4. DMX OUT: used to daisy chain the projector with other units that will be controlled by a DMX-controller.
5. DISPLAY: shows the various menus and the selected functions:
6. MENU-button: used to browse the different menu options or to exit a menu option.
7. ENTER-button: used to select a menu option or confirm a setting.
8. ▲-button: used to go to the previous menu option or to increase a parameter value.
9. ▼-button: used to go to the next menu option or to decrease a parameter value.
10. SAFETY EYE: used to attach a safety cable when the unit is rigged, see paragraph “overhead rigging”.
11. FROST FILTERS: 2 filters (10° and 45°) are included to make the very narrow 4° beam wider. Use the
metal ring to fix one of these filters in front of the 4° lens.
12. HANGING BRACKET: with a knob on both sides to fasten the unit in the desired position. you can use
the hole in the center of the bracket to fix a hook or truss clamp.
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials should
be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don’t cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
BRITEQ®
3/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
SETUP MENU / HOW TO SETUP
With the setup menu you can fully configure the projector. All settings are preserved when the unit is
disconnected from the mains.
 To select any of the functions, press the MODE button until the required function is shown on the display
or use the ▲/▼buttons to browse the menu.
 Select the function with the ENTER button.
 Use ▲/▼buttons to change the values.
 Once the required value is selected, press the ENTER button to confirm.
DMX ADDR
Used to set the desired DMX-address.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the DMX value can now be changed
 Use ▲/▼buttons to select the desired DMX512 address. The last occupied DMX-address is also shown:
this makes it easier to set the address of the next unit in the chain.
 Once the correct address shows on the display, press the [ENTER] button to save it.
Note: on RDM-compatible controllers this option can also be remotely set.
CHANNEL MODE
Used to set the desired channel mode.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
BRITEQ®
4/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
 Use ▲/▼buttons to select the desired mode:
 [1CH]: master dimmer
 [2CH]: master dimmer + strobe
 Once the correct option shows on the display, press the [ENTER] button to save it.
Remark: on RDM-compatible controllers this option can also be remotely set.
SLAVE MODE
Used to set the projector as slave in a master/slave setup.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button
MASTER DIM
Used to set the master dimmer while used as master.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼buttons to select the desired level for the master dimmer. (please note that the last selected
static color will be used to set the value)
 Once you have the desired level, press the [ENTER] button to save it.
Note: the setting of this option has NO effect while the projector is used as SLAVE or in DMX-mode.
DIMMER CURVE
Used to set the dimmer curve of the master dimmer.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼buttons to selected the desired curve:
 Once you have the desired curve, press the [ENTER] button to save it.
LAMP BEHAVIOR
Used to select the reaction time of the projector.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼buttons to select the desired mode:
 [LED]
The projector follows the instructions instantly, no delay.
 [HALOGEN]
The projector imitates the behavior of a halogen lamp (slower reaction time).
 Once the correct option shows on the display, press the [ENTER] button to save it.
LOCK MENU
Used to lock the setup menu against unwanted altering of the settings.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼buttons to select the desired mode:
 [OFF]
The setup menu can be used at any time.
 [ON]
After a short time the setup menu locks automatically, the display shows [LOCKED *****].
Unlock the display by pressing the buttons in this order: UP, DOWN, UP, DOWN, ENTER.
 Once the correct option shows on the display, press the [ENTER] button to save it.
BRITEQ®
5/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
NO DMX BEHAVIOR
Used to set how the projector reacts when the DMX-signal suddenly disappears.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼buttons to select the desired mode:
 BLACKOUT
output turns black while no DMX is detected.
 FREEZE:
output based on the last valid DMX-signal is kept on the projector.
 Once the correct option shows on the display, press the [ENTER] button to save it.
Note: as soon as the input detects a DMX-signal, blackout or freeze mode will be cancelled.
DEFAULT SETTINGS
This is your emergency exit if you really messed up the settings: just return to factory settings.
Also 2 user settings can be saved/loaded.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
 Press the ENTER button: the values can be changed
 Use ▲/▼buttons to selected the desired settings:
 [FACTORY]
 [USER1]
 [USER2]
 Press the [ENTER] button:
 [FACTORY] was selected: the display shows [LOAD]
 Press the [ENTER] button: the display shows [ACTION?]
 Use ▲/▼buttons to select [YES / NO]
 Press the [ENTER] button to confirm.
 [USER1 / USER2] was selected:
 Use ▲/▼buttons to select [LOAD / SAVE]
 Press the [ENTER] button to confirm: the display shows [ACTION?]
 Use ▲/▼buttons to select [YES / NO]
 Press the [ENTER] button to confirm.
 [SAVE] was selected: the current settings of the setup menu are saved to memory.
 [LOAD] was selected: the previously saved settings are loaded.
Default factory settings:
PARAMETER name
DMX Channel mode
MASTER DIM
DIM Curve
LED behavior
Auto Lock Menu
No DMX mode
Defaults factory
CH02
100%
Square
Halogen
OFF
Freeze
USER defaults 1
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
USER defaults 2
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
Current setting in the menu
FIRMWARE VERSION
Used to show the current version of the firmware.
 Press the [MENU] button or ▲/▼buttons until the desired function is showing on the display.
The firmware of this unit can be upgraded using a special upgrade tool with Windows® software. (separately
available from Briteq).
Each time the projector is switched on, the display shows “UPDATE Wait ….”: while this message shows on
the display you can start the update using our special upgrade tool. More information about this can be found
in the user manual of the upgrade tool and / or our website: www.briteq-lighting.com
BRITEQ®
6/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
ELECTRICAL INSTALLATION
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Master / Slave mode:
Connect the projectors together as shown on the drawing. Please refer to the paragraph “SETUP MENU” to
setup the master. All slaves must be set to SLAVE-mode. You can put as many slaves as you like on
condition that the overall power consumption on the power line stays under 10A (2300W).
IMPORTANT: make sure that no DMX-controller is connected, this will result in unexpected behavior!
Electrical installation for two or more units in DMX-mode:
 The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units.
 Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
 To prevent strange behavior of the light effects, due to interferences, you must use a 90Ω to 120Ω
terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work!
 Make sure that all units are connected to the mains.
 Each unit in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode. In the next section you will learn how
to set the DMX addresses.
BRITEQ®
7/9
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
RDM FUNCTIONS / REMOTE SETUP
RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which
means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of
these functions are briefly explained below, others will be added in the future.
 The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique
device ID.
 The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.
The projector will respond:
 Device name:
BEAMSPOT1-DMX NW (WW)
 Manufacturer:
Briteq®
 Category:
LED Dimmer
 Firmware: x.x.x.x
(firmware version of the projector)
 DMX address: xxx
(current DMX start address of the projector)
 DMX footprint: xx
(number of DMX-channels used by the projector)
 Personality: xx
(current personality [or DMX-working mode] used by the projectors)
 The DMX-controller can send certain commands to each RDM device which allow remote setup of the
units. Thanks to this the projector can be setup remotely.
The following functions can be managed remotely:
No more need to take a ladder and set all units one by one!
 DMX START ADDRESS: The start address can be set remotely from 001 to xxx.
 PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.
These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMXcontroller and send these data to all projectors at once. More functions will be added later.
OPERATING INSTRUCTIONS
Note: when the projector is switched on the display shows “UPDATE WAIT …” This message informs you
that IF you want to upgrade the firmware, you should do it while this message is shown on the display. For
normal use you can ignore this message completely.
A. Standalone 1unit:
 Just connect the projector to the mains.
 Adjust the master dimmer [MASTER DIM] if necessary
 Refer to chapter HOW TO SETUP to learn how to set the menu options.
B. Two or more units in master/slave setup:
 Connect the units together. Refer to the chapter “electrical installation” to learn how to do this.
 Adjust the master dimmer [MASTER DIM] on the 1st unit (master unit).
 Set all the other projectors in SLAVE mode
 The slave projectors will now follow the settings of the master projector so they all work
synchronously.
C. Controlled by universal DMX-controller:
 Connect all units together. Refer to the chapter “Electrical installation for two or more units in DMXmode” to learn how to do this (don’t forget to address all units properly!)
 Connect all units to the mains and turn on the DMX controller.
Since each unit has its own DMX-address, you can control them individually. Remember that each unit
can use a different number DMX-channels, depending on the DMX-mode you have selected in the
menu. See the different DMX charts below:
DMX Chart for the 1 channel DMX-Mode
Channel:
Value:
Function:
1
Master dimmer (0-100%)
000-255
DMX Chart for the 2 channel DMX-Mode
Channel:
Value:
Function:
1
Master dimmer (0-100%)
000-255
Open
000-005
2
Increasing strobe speed
006-255
BRITEQ®
8/9
Remarks:
Remarks:
No strobe
006 = slow 255 = fast
BEAMSPOT1-DMX NW (WW)
ENGLISH
OPERATION MANUAL
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
Mains Input:
AC 100 - 240V, 50/60Hz
Power consumption:
17 Watt
Power connections:
Neutrik® PowerCON® - 10A Power linking capacity.
DMX connections:
3pin-XLR male / female
DMX channels used:
2 modes (1ch + 2ch)
Lamp:
LED, 15W Natural white 4500K (or warm white 3200K)
CRI-factor:
>90
Beam Angle:
4° (10° + 45° with frost filter)
IP-Rating:
IP20
Size:
see drawing
Weight:
1.4 kg
The information might be modified without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
BRITEQ®
9/9
BEAMSPOT1-DMX NW (WW)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising