LAURA ASHLEY ROPER RHODES CLIFTON BASIN MIXER

LAURA ASHLEY ROPER RHODES CLIFTON BASIN MIXER
ADJUSTING HANDLE ALIGNMENT
To adjust the alignment of the handle in
relation to the body, unscrew the bezel and
ceramic indices from the top of the handle.
Unscrew the spindle bolt, and set aside
with the spindle bolt washer.
Lift the handle off the spindle and replace at
the desired angle using the micro
adjustment teeth.
Bezel and Ceramic
indices assembly
Spindle Bolt
Washer
Handle Body
Micro Adjust
teeth
Re-attach the washer and spindle bolt and
tighten.
Spindle
Screw the bezel and ceramic indices
assembly back onto the handle body.
ADJUSTING CERAMIC INDICES
To adjust the alignment of the ceramic indices, first
unscrew the bezel and ceramic indices assembly from
the tap handle.
CLIFTON BASIN MIXER WITH POP-UP WASTE
INSTALLATION & AFTERCARE INSTRUCTIONS
Bezel
Ceramic Indices
Brass Plate
The ceramic indices are held in place by a threaded brass
plate. Loosen the brass plate with a No. 16 Hex (Allen)
Key, but do not remove from bezel.
Rotate the ceramic indices until the printed logo is at the
desired position. You may need to screw the bezel and
indices assembly back onto the handle body to check
alignment and adjust as necessary.
No. 16
Hex Key
When you are happy with the position, re-tighten the
brass plate , making sure to hold the ceramic indices still.
Customer Services
Laura Ashley Bathrooms, Brassmill Lane Trading Estate, Bath BA1 3JF
Tel: 01225 303 900 | Fax: 01225 448 877
Email: info@lauraashleybathroomcollection.com Web: www.lauraashleybathroomcollection.com
Manufactured by Roper Rhodes under license for Laura Ashley Ltd.
REF: PL.LA. | 03.13 V1.01
LA1016
RETAIN FOR FUTURE REFERENCE
CLIFTON BASIN MIXER WITH POP-UP WASTE
INSTALLATION & AFTERCARE INSTRUCTIONS
INSTALLATION PROCEDURE
1) Prior to installation flush out the pipe work to remove debris and then ensure the water supply is
turned off.
Pop-Up Waste Lever
2) Refer to diagram and ensure all components are present.
3) Fit the flexible tail hoses into the base of the basin mixer body using an appropriate spanner. Make
sure you do not over tighten. Insert the pop-up waste lever through the hole behind the spout.
4) Insert the rubber washer into the bottom of the basin mixer and place over the basin tap hole.
Secure on the underside using the horseshoe washer, horseshoe plate and securing bar in the order
shown. Do not overtighten as this may damage the basin.
Rubber Washer
Basin
Fixing Bolt
Horseshoe Washer
Metal Horseshoe Plate
5) Connect the pop-up waste mechanism as indicated in the diagram. The pop-up rod connector should
be adjusted to allow for a smooth operation. The base of the plug should also be adjusted to allow it to
open sufficiently for waste water to escape. Do not adjust such that the waste sits too high in the open
position as this may cause the mechanism to stick. Ensure the basin seal sits between the upper part of
the waste and the inside of the basin. The waste washer should be positioned on the underside of the
basin.
Securing Bar
6) Connect the water supply to the flexible hoses, making sure the hot supply is connected to the left
hose (flexible hose 1 in the diagram).
Flexible Hose 2
7) Fully open both hot and cold taps and allow to run for approximately 1 minute to fully flush the
system.
Flexible Hose 1
8) Check all connections for leaks.
Pop-Up Waste Lever
AFTERCARE INSTRUCTIONS
Whilst the item has a high quality durable finish, it should nevertheless be treated with care.
Surfaces should be cleaned only using a soft damp cloth and clean water and dried using a soft
cotton cloth. Bath cleaning products, even non scratch ones could damage the finished surface.
10 YEAR GUARANTEE
We have complete confidence in this Laura Ashley product and as such it is offered with a 10-year
guarantee against defects in manufacture. The guarantee requires that this product be used in the
manner for which it was intended and that it is installed and maintained in accordance with the
fitting instructions and local water bylaws. The guarantee covers products in domestic use only.
The guarantee is invalidated should the valve be damaged by water borne debris. Make sure that
supply pipes are clear of any debris prior to installation, this is particularly important on new
plumbing installations. In the unlikely event that this product should fail during the guarantee
period we will either replace the faulty part or the complete unit as appropriate.
Basin Seal
Basin
Waste Washer
Pop-Up Rod Connector
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising