Lock Mortiser and Lock Face Templet Instruction manual

Lock Mortiser and Lock Face Templet Instruction manual
ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 31
Instruction
manual
Lock Mortiser and
Lock Face Templet
MODEL
513 Mortiser
MODEL 517 Lock Face Templet
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
Copyright © 2003 Porter-Cable Corporation
Part No. 904667 - 11-10-03
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize
this information, we use the symbols below. Please read the manual and pay attention to these
sections.
indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
indicates a potentially hazardous situation which, if not avoided,may result in
minor or moderate injury.
used without the safety alert symbol indicates potentially hazardous situation
which, if not avoided, may result in property damage.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some example of these chemicals are:
●
lead from lead-based paints
●
crystalline silica from bricks and cement and other masonry products
●
arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, always wear MSHA/NIOSH approved, properly fitting face mask or
respirator when using such tools.
GENERAL SAFETY RULES
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire
and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases, or dust. Power tools create
sparks which may ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove
the grounding prong or modify the plug in any way. Do not use any
adapter plugs. Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. If the tools should electrically
malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
2. Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is grounded.
3. Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
2
5. When operating a power tool outside, use an outdoor extension
cord marked “W-A” or “W”. These cords are rated for outdoor use and
reduce the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is OFF before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have
the switch ON invites accidents.
4. Remove adjusting keys or wrenches before turning the tool ON. A
wrench or a key that is left attached to a rotating part of the tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in unexpected
situations.
6. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for
appropriate conditions.
7. Use certified safety equipment. Eye protection equipment should
comply with ANSI Z87.1 standards, hearing equipment should comply with
ANSI S3.19 standards, and dust mask protection should comply with
MSHA/NIOSH certified respirator standards.
TOOLS USE AND CARE
1. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2. Do not force tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is
designed.
3. Do not use tool if switch does not turn it ON or OFF. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
4. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
6. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting edges are less likely to bind
and are easier to control.
7. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If
damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may become
hazardous when used on another tool.
3
SERVICE
1. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a
risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance Section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
SPECIFIC SAFETY RULES AND SYMBOLS
1. Accessories must be rated for at least the speed recommended on
the tool warning label. Wheels and other accessories running over rated
speed can fly apart and cause injury.
2. Hold tool by insulated gripping surfaces when performing an
operation where the cutting tools may contact hidden wiring or its own
cord. Contact with a “live” wire will make exposed metal parts of the tool
“live” and shock the operator.
3.
DO NOT OPERATE MOTOR UNIT UNLESS
MOUNTED IN LOCK MORTISER CARRIAGE.
4. Be sure cord is free and will not “hang up” during operations.
5. Keep hands clear of cutter when motor is running to prevent
personal injury.
6. Stay alert and keep cutter clear of all foreign objects while motor is
running.
7. Be sure motor has completely stopped before withdrawing cutter
from machined mortise.
8. Some wood contains preservatives which can be toxic. Take extra
care to prevent inhalation and skin contact when working with these
materials. Request and follow any safety information available from your
material supplier.
Improper operation or maintenance of this product could result
in serious injury and property damage. Read and understand all warnings and
operating instructions before using this tool. When using power tools, basic
safety precautions should always be followed to reduce the risk of personal
injury. For additional information visit our website www.porter-cable.com.
Additional Information regarding the safe and proper operation of power tools
(i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Additional
Information is also available from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201, the American National Standards Institute ANSI
01.1Safety Requirements for Woodworking Machines, and the U.S. Department
of Labor regulations.
This tool was designed for certain applications. DO NOT
modify and/or use it for any application other than for which it was designed.
If you have any questions relative to its application, DO NOT use the tool
until you have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
4
SYMBOL
V
A
Hz
W
kW
µF
l
kg
N/cm2
Pa
h
min
s
........................
........................
........................
........................
........................
........................
........................
........................
........................
........................
........................
........................
........................
DEFINITION
volts
amperes
hertz
watts
kilowatts
microfarads
liters
kilograms
newtons per square centimeter
pascals
hours
minutes
seconds
........................ alternating current
3
........................ three-phase alternating current
3N
........................ three-phase alternating current with neutral
n0
........................ direct current
........................ no load speed
........................ alternating or direct current
........................ Class II Construction
........................ splash-proof construction
........................ watertight construction
…/min
........................ revolutions or reciprocation per minute
REPLACEMENT PARTS
When servicing, use only identical replacement parts.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.
Do not operate your tool on a current on which the voltage is
not within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found
in this section. This table is based on limiting line voltage drop to 5 volts (10
volts for 230 volts) at 150% of rated amperes.
5
If an extension cord is to be used outdoors it must be marked with the suffix
W-A or W following the cord type designation. For example – SJTW-A to
indicate it is acceptable for outdoor use.
Nameplate Ampere Rating
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft.
0-2
2-3
3-4
4-5
5-6
6-8
8-10
10-12
12-14
14-16
16-18
18-20
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
Length of Cord in Feet
100 Ft. 150 Ft. 200 Ft. 250 Ft.
200 Ft. 300 Ft. 400 Ft. 500 Ft.
18
16
16
14
14
12
12
10
10
10
8
8
16
14
14
12
12
10
10
8
8
8
8
6
16
14
12
12
10
10
8
8
6
6
6
6
300 Ft.
600 Ft.
14
12
12
10
10
8
8
6
6
6
4
4
14
12
10
10
8
6
6
6
6
4
4
4
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
12
10
10
8
8
6
6
4
4
4
2
2
12
10
8
8
6
6
4
4
2
2
2
2
FUNCTIONAL DESCRIPTION
FOREWORD
Model 513 Lock Mortiser permits builders and contractors to quickly cut
true, accurate mortises for door box locks.
Model 517 Lock Face Templet allows quick and economical routing for lock
faces on doors after the mortise cut for the lock itself has been completed.
LOCK MORTISER ASSEMBLY
STANDARD EQUIPMENT
With the mortiser, the four sections of the height rod (A), and two bits (B) are
furnished. See Fig. 1.
A
B
Fig. 1
ASSEMBLY OF BASE UNIT
The unit is shipped with the crank handle disassembled.
Place crank handle (D) to crank shaft (A) (See Fig. 2) with wooden knob
facing outward and “D” hole in handle aligned with flat on shaft. Place bolt
(C) through washer (B) and thread into shaft (A). Tighten securely.
5
6
A
B
C
D
Fig. 2
ASSEMBLY OF MOTOR UNIT
DISCONNECT TOOL FROM POWER SOURCE.
1. Open hardware package and locate: two cap screws, two flat washers,
and 5/32" (4.0 mm) allen wrench. Place washers onto cap screws.
2. Insert splined cutter shaft (see Fig. 3) through motor carriage (L) and into
the spiral grooved bushing (M) in the main frame (N). Orient motor as shown
in Fig. 8 and seat into motor carriage.
3. Insert the two screw and washer assemblies (from Step 1) through motor
carriage (see Fig. 4) and thread into the threaded holes in motor housing.
Tighten securely with allen wrench.
SCREWS & WASHER
L
N
M
Fig. 3
Fig. 4
OPERATION
DETERMINE WIDTH OF CUT
Measure the width of the lock box at its widest point, including any
protruding parts. DO NOT INCLUDE THE LOCK FACE. Select a cutter equal
to, or slightly larger than this width.
Example: 1) Overall width of lock box – 31/32" (24.6 mm) – Use
PORTER-CABLE #43704 1" (25.4 mm) diameter bit.
2) Overall width of lock box – 3/4" (19.1 mm) – Use
PORTER-CABLE #43703 3/4" (19.1 mm) diameter bit.
Various sizes of bits are available as accessories.
7
DISCONNECT TOOL FROM POWER SOURCE and
exercise extreme care when handling cutter to avoid bodily injury or
damage to cutting edge.
Thread selected bit onto end of splined cutter shaft and tighten securely.
DETERMINING LENGTH OR HEIGHT OF CUT
Measure the height of the lock box (see Fig. 5) including any protruding
parts. DO NOT INCLUDE THE LOCK FACE.
Fig. 5
SETTING MORTISER FOR LENGTH OF CUT
DISCONNECT TOOL FROM POWER SOURCE.
See Fig. 6 to set mortiser for length of cut. Loosen crank pin nut (T) and turn
adjusting knob (U) until the correct graduation mark on the slide lines up with
the line on crank pin indicating washer. If it is difficult to turn the adjusting
knob (U), turn the crank (E) Fig. 8, until most of the tension is relieved.
Tighten crank pin nut (T), Fig. 6, securely.
EXAMPLE: If the mortise is to be 4" (101.6 mm) long, turn adjusting
knob (U) until the Fig. 4 graduation mark lines up with the line on the
crank pin indicating washer.
T
U
Fig. 6
8
SETTING MORTISER FOR DEPTH OF CUT
DISCONNECT TOOL FROM POWER SOURCE.
Measure the lock box at its deepest part, including the thickness of the lock
face, and add 1/4" (6.4 mm) to this dimension for clearance. The depth of cut is
controlled by the feed rod (W) Fig. 7 which is marked in 1/4" (6.4 mm)
increments. Loosen the collar (X) and move it to the determined depth
requirement and lock in place.
W
X
Fig. 7
MAKING TRIAL CUT
After the mortiser (see Fig. 8) has been set up according to the preceding
instructions, it is strongly recommended that a trial cut be made in the
following manner to insure fit of lock box.
1. Clamp a length of 2" × 6" (50.8 x 152.4 mm), or larger, lumber in vise, or
fasten it securely to a work bench, in an upright position.
DISCONNECT TOOL FROM POWER SOURCE.
2. Move feed lever (A) to horizontal position (as shown in Fig. 8) and pull
motor carriage (B) to end of guide rod (C).
3. Place the mortiser against edge of the 2" × 6" (50.8 x 152.4 mm) so that
the clamps are firmly seated and crank (E) is free to revolve completely
around. Tighten clamp handles (D) securely to hold mortiser in position.
4. Move feed lever (A) to vertical position to engage feed mechanism.
Make sure motor switch is in the OFF position.
B
C
D
A
E
Fig. 8
9
F
5. Connect mortiser to power source.
6. Turn motor switch ON and rotate crank (E) until collar (F) hits feed
housing, stopping depth of cut and completing mortise.
7. Turn motor OFF.
DISCONNECT TOOL FROM POWER SOURCE.
8. Move feed lever (A) to horizontal position to disengage feed mechanism.
9. Grasp motor carriage (B), Fig. 9, with both hands and pull towards you until
bit is clear of cut mortise. Remove
mortiser from 2" × 6" (50.8 x 152.4 mm).
B
10. Clean all chips from cut and try
lock box for fit. If necessary, readjust
mortiser as required and make another
trial cut.
NOTE: Be sure the length of the
mortise has not removed stock
required for the two screws that
retain the lock box to the door.
MORTISING A DOOR
Fig. 9
After trial cut has been made resulting in a satisfactory fit for the lock box,
the door should be mortised in the following manner.
1. Place door in an upright position and anchor securely. If door is hung,
use wedges under bottom of door to keep it from moving.
2. Place lock box against side of door so that the door knob will be the
desired distance from the floor.
3. Make a mark on the side of the door at the top of the lock box (See
Fig. 10). Transfer this mark to the front edge of the door.
4. Draw a line 3/8" (9.5 mm) above this mark across the front edge of the
door. This is required for clearance for the radius of the cutter. NOTE: The
actual clearance may be determined from the lock box and the trial cut in the
2" × 6" (50.8 x 152.4 mm). This clearance may be used in place of
3/8" (9.5 mm).
DISCONNECT TOOL FROM POWER SOURCE.
5. Turn mortiser crank handle until the bit is in the top most position.
6. Place the mortiser on the door so that the top edge of the bit just
touches the line drawn on edge of the door.
7. Mortise door in the same manner as outlined under MAKING A TRIAL CUT.
Fig. 10
10
PRODUCTION LOCK MORTISING
If you have a number of doors with the locks at the same height, the height
rod attachment (see Fig. 11) will be of great value. After you have determined
the height you want, and have the lock mortiser in position on the first door,
assemble the four rods that compose the height rod attachment. Insert the
rods in the mortiser and place the height rod stop (G) on the top of the rod so
it rests on the top of the door. Lock the height rod screws, (H) Fig. 11A. To
locate the mortiser on the next door, simply place the mortiser on the door
with the height rod stop resting on the top of the door and tighten the
clamps. This will assure having all locks located in the same position.
G
H
Fig. 11A
Fig. 11
MODEL 517 LOCK FACE TEMPLET
REQUIRED EQUIPMENT
Equipment required for use with Router and Lock Face Templet.
42024 Templet Guide
42237 Locknut
43440 5/8" (15.9 mm) Diameter Straight Bit
SETTING UP TEMPLET
1.
2.
Loosen locking screw (A), Fig. 12.
Adjust side guides (C), Fig. 12, so the space between them is
1/8" (3.2 mm) wider than the lock face.
3. Firmly tighten screw (A).
4. Loosen locking screw (D), Fig. 12.
5. Adjust guide bar (E), Fig. 12, distance between (E) and (B) is
1
/8" (3.2 mm) longer than the lock face.
6. Firmly tighten screw (D).
11
LOCATING TEMPLET ON DOOR
1. Draw a line across the door edge at the center of the mortise cut for the
lock.
2. Draw line (F), Fig. 12, on the templet side guides (C), midway between
bars (B) and (E).
3. Position templet on door so line (F) on templet matches line drawn on
the door edge at the center of the mortise cut.
4. Tighten the two wing screws (G), Fig. 12 to lock templet in place.
D
C
E
C
G
B
F
G
A
Fig. 12
PREPARING ROUTER
DISCONNECT ROUTER FROM POWER SOURCE.
1. Assemble 42024 templet guide to router base with 42237 lock nut.
2. Install bit in router collet.
3. Set router on lock face templet and adjust depth of cut so bit just
touches door.
4. Set router depth adjusting ring to zero position.
5. Lift router from templet and adjust depth of cut equal to thickness of lock
face.
6. Firmly tighten motor locking device.
MAKING THE CUT
Make sure router switch is in the “OFF” position.
1. Connect router cord to power source.
2. Start router and mortise door for lock face, guiding the router by
keeping the templet guide against the templet guide bars.
3. A corner chisel 42234 is available as an accessory for squaring the
corners for the lock face.
FINISHED MORTISE
Fig. 13 shows how the mortise will look when completed. The cut is smooth
and even and the lock
box may be inserted
with no further hand
work. In Fig. 13 the lock
face templet has been
used and the corner
chisel has squared the
corners, assuring a
perfect fit.
Fig. 13
12
MAINTENANCE
KEEP TOOL CLEAN
Keep the mortiser attachment free of dust and dirt, especially the vertical
tubes on which the main frame slides. Periodically blow out all air passages
with dry compressed air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They could possibly
dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug
are making good contact in the outlet. Also, check for blown fuses or open
circuit breakers in the line.
MORTISER LUBRICATION
A few drops of oil applied with an oil rag is advisable once every day or two
on the vertical tubes.
NOTE: DO NOT OIL THE SPLINED CUTTER SHAFT.
It is advisable to apply a few drops of bearing oil to each end of the crank
every day or two.
BRUSH INSPECTION AND LUBRICATION
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA
FACTORY SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have
new brushes installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO
OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is
present, return your tool to the service station for immediate service.
13
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA FACTORY
SERVICE CENTER. All repairs made by these agencies are fully guaranteed
against defective material and workmanship. We cannot guarantee repairs
made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable ·
Delta Supplier, Porter-Cable · Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
Since accessories other than those offered by PorterCable· Delta have not been tested with this product,
use of such accessories could be hazardous. For safest
operation, only Porter-Cable · Delta recommended
accessories should be used with this product.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
14
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
COLORADO
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77038
4321 Sam Houston Parkway, West
Suite 180
Phone: (281) 260-8887
Fax: (281) 260-9989
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service
Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable • Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos PorterCable • Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable • Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable • Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable • Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits PorterCable • Delta, s’adresser à tout distributeur Porter-Cable • Delta, centre de service agréé ou centre de service d’usine Porter-Cable • Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable • Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 Ave.
St-Jean Baptiste, Suite 180
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®,
Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®,
Micro-Set ®, MIDI LATHE ®, MORTEN™, NETWORK™, OMNIJIG ®, POCKET CUTTER ®, PORTA-BAND ®, PORTA-PLANE ®, PORTERCABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™,
QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®,
Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®,
Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets
d’invention et marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A. PC-0603-150
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising