refrigerator - Sears Parts Direct

refrigerator - Sears Parts Direct
LRSC21935TT
LRSC21935SW
LRSC21935SB
REFRIGERATOR
UseCs Guide
Please read this guide thoroughly
before operating and keep it handy for
:e at all times.
manuel
]e
Lea detenidamente
!@i!_i!ii!ii!ii!i!!i!!!!i!
iiiiiiiiiiiiiiiiiiiiiiii/iiiiili!iii!!iiiiiiiiiiiiiiiiiiii
iliiiiiil)iii_i_/iiiiiiiiiiii!i!i!i_)iii_i
Table of contents
Introduction
Entry
Important
safety instruction
Identification
Installation
Where
of parts
to install
Door
removal
Door
replacement
Feed water
Water
connection
Operation
Height
Operation
pipe installation
instruction
instruction
guide
guide
adiustment
Starting
Adjusting
the temperatures
(Dispenser
/ Automatic
Shelf (Applicable
Wine
holder
and functions
ice maker)
to some models only)
(Applicable
to some models only)
Egg box
Humidity
Convert
control
into a vegetable
Deodorizer
Suggestion on
food storage
Care and
maintenance
in the vegetable
(Applicable
Location of foods
Storing foods
How to dismantle parts
General information
Cleaning
Trouble shooting
compartment
or meat compartment
to some models only)
Entry
The model and serial numbers are found on the inner case or back of refrigerator
compartment of this unit. These numbers are unique to this unit and not
available to others. You should record requested information here and retain
this guide as a permanent record of your purchase. Staple your receipt here.
Date of purchase
Dealer purchased from
Dealer address
Dealer phone no.
Model no.
Serial no.
Important
safety
instruction
Before it is used,this refrigerator must be properlyinstalledand located in accordancewith
the installationinstructionsin this document,
Never unplugyour refrigeratorby pulling on the power cord, Alwaysgrip plug firmly and pull
it straightout from the outlet,
When moving your applianceaway from the wall, be carefulnot to roll overthe power cord
or to damageit in any way,
After your refrigeratoris in operation,do not touch the cold surfaces in the freezer
compartment, particularlywhen your handsare damp or wet, Skincould adhereto these
extremely cold surfaces,
Unplugthe power cord from the power outlet for cleaningor other requirements, Never
touch it with wet handsbecauseyou canget an electricshock or be hurt,
Never damage,process,severelybend,pull out, or twist the power cord becausedamage
the power cord may causea fire or electricshock, You havedoubts on whether the
applianceis properlygrounded,
Never placeglassproducts in the freezerbecausethey may be brokendue to expansion
when their contents are frozen.
Never allowyour handswithin the ice storage bin of the automatic ice maker.You could be
hurt by the operationof the automatic ice maker,
Theapplianceis not intendedfor useby young childrenor infirm persons without
supervision,
Youngchilderenshouldbe supervisedto ensurethat they do not playwith the appliance,
Never allow anyoneto climb, sit, stand or hang on the refreshment center door, These
actionsmay damagethe refrigeratorand even tip it over, causingsevere personalinjury.
Recommended
Grounding
Method
Beforeyou move your refrigeratorinto its final location,
it is importantto make sure you havethe proper electrical
connection:
A 115 Volt, 60 Hz,,AConly 15 or 20 ampere fused,grounded
electricalsupply is required,It is recommendedthat a separate
circuitserving onlyyour refrigeratorbe provided,Use an outlet that
cannot be turned off by a switch. Do not use an extensioncord.
Accessibility
of
Supply Plug
Supply Cord
Replacement
/_Warning
Therefrigerator-freezershouldbe so positionedthat the supply plug
is accessiblefor quick disconnectionwhen accidenthappens,
If the supplycord is damaged,it must be replacedby the manufactureror its serviceagentor
a similarlyqualifiedpersonin order to avoida hazard,
Do not modify or extend the Power Cord length.
• It will cause electric shock or fire.
Child entrapment
warning
Don't store
Grounding (Earthing)
DANGER: Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors but leavethe shelves in place so that children may not easily climb
inside.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not playwith the appliance.
Don't store or use gasoline or other flammable vapor and liquids in the vicinity of this or
any other appliance.
In the event of an electric short circuit, grounding (earthing)reduces the risk of electric
shock by providing an escape wire for the electric current,
In order to prevent possible electric shock, this appliance must be grounded
improper use of the grounding plug can result in an electric shock. Consult a qualified
electrician or service person if the grounding instructions are not completely
understood, or if you have doubts on whether the appliance is properly grounded.
Identification
of parts
Freezer
Refrigerator
compartment
compartment
Milk productcorner
Lamp
Door rack
............................
Shelf
Door rack
Automatic
icemaker
Lamp
...................................
Wine holder(Optional)
Shelf
Snackdrawer (Optional)
Shelf
(steel or glass)
Eggbox
Lamp
Door rack ........................
(Optional)
Vegetabledrawer(1or 2)
Door rack
Shelf
Drawer(1 or 2)
Door rack
(Optional)
Lowercover ..............................................................................
Vegetable
drawer/Meatdrawer
Humidity switch
Conversionswitch
(Meats/Vegetables)
Where to install
Select a good
location
1. Place your appliance where it is easy to use.
2. Avoid placing the unit near heat sources, direct sunlight or moisture.
3. To avoid vibrations, the appliance must be leveled.
4. Don't install the appliance below 504",,.
It may cause affect the performance.
Door removal
z_
Warning
ElectricShock Hazard
Disconnect electricalsupply to refrigerator before installing.
Failureto do so could result in death or serious injury.
If your access door is too narrow for the
_,_
refrigerator to passthrough, remove the
Remove lower
cover and
then feed water
tube
Remove the
freezer
compartment
door
refrigerator door and passthe refrigerator laterally.
Removethe lower cover by lifting upward, and
then pull up the feed water tube while pressing
area ¢ shown in the figureto the right.
[_
_:::_-_--J_
Lower
--
Uppe_hing /J'_ "j
2) Removethe keeper by rotating it counter
clockwise (@)and then lifting the upper
hinge up (@).
',\ __
Kee?_
,gx
3) Removethe freezer compartmentdoor by
lifting it upward.This time, the door should
be lifted enough for the reed water pipe tube
to be completely pulledout.
Lower hinge
Remove the
refrigerator
door
_
Hinge
/" ..................
...... Connection
cover //f_"
w res
)_,
1) Removingthe hinge cover by loosening the
screws.Separateall connectionwires except
for the earth line after.
; _
_
J _/:;_1
_/
"@"k.
Feed water
tube
1) Loosen the hinge cover screws and remove
the cover, Remove connection wire, if any,
except for the earth line.
wires
2) Remove keeper by rotating it clockwise (@)
and then remove the upper hinge by lifting
it up (@).
3) Removethe refrigeratorcompartment door
by lifting it up.
Lower hinge
EarthNne
[_pei hinge
cover
Pass the
refrigerator
Passthe refrigerator laterally through the access
door as shown in the right figure,
Door replacement
Mount them in the reverse sequence of removal after they pass through the access
door.
Feed water pipe installation
Before
installation
• Automatic ice maker operation needs water pressure of 147-834 kPa (1.5-8.5
kgr/cm 2)(That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).
• If water pressure does not reach the rating 147 kPa (1.5 kgf/cm 2) or below, it is
necessary to purchase a separate pressure pump for normal automatic icing and
cool water reed.
• Keep the total length of the feed water pipe tube within 8 m and be careful for the
tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed
owing to the drain water pressure.
• Install the reed water pipe tube at a place free from heat.
Warning
• Connect to potable water supply only.
• Refer to instructions with water filter kit for installation.
Water connection
Connecting
the refrigerator
to a water source
Warning
Tools required
instruction guide
Read all directions carefully before you begin.
Connect to potable water supply only.
• Standard screwdriver
• 7/16 - inch and 1/2 -inch open-end wrenches or two adjustable wrenches
• 1/4 -inch nut driver
• 1/4 -inch drill bit
• Hand drill or electric drill (properly grounded)
Cold water supply
The ice maker water valve contains a flow washer which is used as a water
pressure regulator.
The ice maker needs to be connected to a cold water line with water pressure
207 o-827 kPa (30 o- 120 psi).
Ira problem occurs, call your utility company.
Connect
the tubing to
water line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long enough to empty
water pipes.
3. Find a 1/2 -inch to 1-1/4 -inch vertical COLD water pipe near the refrigerator,
4. To determine the length of copper tubing you will need, measure from the
connection on the lower left rear of the refrigerator to the water pipe. Add 7
feet (2.1m)to allow for moving refrigerator for cleaning. Use 1/4 -inch O.D.
(outside diameter) copper tubing. Be sure both ends of copper tubing are cut
square.
5. Using a grounded drill, drill a 1/4 - inch hole in the cold water pipe you have
selected.
6. Fasten shut - off valve to cold water pipe with pipe clamp. Be sure outlet end
is solidly in the 1/4dnch drilled hole in the water pipe and that the washer is
under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do not over tighten or
you may crush the copper tubing, especially if soft (coiled) copper tubing is
used. Now you are ready to connect the copper tubing.
7. Slip compression sleeve and compression nut on copper tubing as shown.
Insert end of tubing into outlet end squarely as far as it will go. Screw
compression nut onto outlet end with adjustable wrench. Do not over tighten.
8. Place the free end of the tubing into a container or sink, and turn ON main
water supply and flush out tubing until water is clear. Turn OFF shut- off valve
on the water pipe. Coil copper tubing.
Pipe
Packing Nut\
Coil of polyethylene or
Copper Tubing
Shut Off Valve
Compression Sleeve
Compression Nut
Operation
Connect the tubing to
the refrigerator
instruction guide
Before making the connection to the
refrigerator, be sure the refrigerator
power cord is not plugged into the wall
outlet.
Copper tubing
(Provided)
Compression nut
(Provided)
1. Remove the plastic flexible cap from
the water valve.
*_
Ferrule
2. Place the compression nut and ferrule
(sleeve) onto the end of the tubing as
shown.
3. Insert the end of the copper tubing into
the water valve connection as far as
possible. While holding the tubing,
tighten the fitting.
Turn the water on at
the shutoff valve
Automatic ice maker
Tighten any connections that leak.
• Plug In the Refrigerator
Arrange the coil of copper tubing so that it does not vibrate against the back of
the refrigerator or against the wall. Push the refrigerator back to the wall.
• Start the Icemaker
Set the ice making stop switch to the ON position The icemaker will not begin
to operate until it reaches its operating temperature of 15 °F (-9 °C) or below. It
will then begin operation automatically if the ice making stop switch is in the
ON position.
• The automatic ice maker can automatically make 8 pieces of ice cube at a time,
80-100 pieces a day.
But these quantities may be varied according to various conditions including
how many times the refrigerator door opens and closes,
• Ice making stops when the ice storage bin is full.
When ice maker
does not operate
smoothly
Ice is clumped together
• When ice is clumped together, take the ice clumps out oftheice storage bin,
break them into small pieces, and then place them into the ice storage bin
again.
• When the ice maker produces too small or clumped ice, the amount of water
supplied to the ice maker need to adjusted. Contact the service center.
• If ice is not used frequently, it may clump together.
Power failure
• Water may drop into the freezer compartment. Take the ice storage bin out and
discard all the ice then dry it and place it back.
The unit is newly installed
• It takes about 12 hours for a newly installed refrigerator to make ice in the
freezer compartment.
CAUTION
Throw away the ice (about 20 pieces) first made after refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or
feed water box.
This is also necessary if the refrigerator has not been used for a long time.
Never store beverage cans or other foods in ice storage bin for the purpose of rapid
cooling.
Such actions may damage the automatic ice maker.
Never remove the ice maker cover.
Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice may pile upjust around the ice maker causing the ice maker to think that the ice
storage bin is rul.
If discolored ice is dispensed, immediately contact Service Center.
Do not use until problem is solved.
Height adjustment
If the freezer
compartment door
is lower than the
Levelthe door by inserting flat (- type) driver into the groove of the left height adjusting
screw and rotate it clockwise (0).
Height difference
refrigerator
compartment door
q-4
Left height
adjustment screw
If the freezer
compartment door
is higher than the
refrigerator
compartment door
Levelthe door by inserting flat (- type) driver into the groove of the right height
adjusting screw and rotate it clockwise (0).
Height difference
1
N
_
Right height
adjustment screw
After leveling the
door height
Next
The refrigerator doors will close smoothly by heightening the front side by adjusting
the height adjusting screw. If the doors do not close correctly, performance may be
affected.
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their
proper places.They are packed together to prevent possible damage during shipping.
3. Connect the power supply cord (or plug) to the outlet. Don't double up with other
appliances on the same outlet.
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating
temperatures for 2-3 hours prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
AdJusting the temperatures and functions
Water/Ice Output
Dispenser
Push Switch
Dispenser Lamp
(Bottom ceiling of
funct+bn d+splayboard)
j_
Function display board
EXPRESSFRZ DISPENSER FREEZERREFRIGERATOR
FILTERRESET LOCK
Lock button.
Dispenser
selection button.
for freezer compartment.
Filter reset button.
Temperature adjustment button
for refrigerator compartment.
You can adjust temperature of and freezer room and refrigerator room,
How to adjust the
temperature
in
the freezer
compartment
F_eezer room temperatureadjustment
FREEZER
Setting
temperature
How to adjust the
temperature
in
the refrigerator
compartment
,_frigerator roomtemperatureadjustment
REFRIGERATOR
Setting
temperature
L_IL._°F
FRZ TEMP
_._ll
°F
FRZ TEMP
FRZTEMP
FRZTEMP
FRZTEMP
_:_
Whenever pressing button, setting is repeated in the order of (Middle) ÷
(Middle Strong) -_ (Strong) ÷ (Weak) -_ (Middle Weak).
• The actual inner temperature varies depending on the rood status, as the
indicated setting temperature is a target temperature, not actual temperature
within refrigerator.
• Refrigeration function is weak in the initial time. Please adjust temperature as
above after using refrigerator for minimum 2-3 days.
Dispenser use
selection
You can select water or ice.
_:_Please select
water, slice ice and square ice by
_SPENSER
pressing
button as you desire.
_ Please press the push button lightly by catching and
pushing in cup.
• The border line is indicated for the selected function,
• "Tak!" sounds if 5 seconds pass after ice comes out.
It is sound that the outlet of ice is closed.
• Reference
: Please wait for 2-3 seconds in order to take final ice
slices or drops of water when taking out cup from the
pressing switches
after taking ice or water.
DISPENSER
Pressing
Switch
.........
Automatic
ice
maker
• The icemaker can automatically make 8 pieces of ice cubes at anyone time,
approximately 80 pieces per day. However these quantities may vary according to
certain conditions. E.g. the duration and amount of times the refrigerator door is
opened.
• The Ice making proceeds ceases automatically when the ice storage bin is full.
• If you choose not to use the automatic ice making function, repositioned the
icemaker selection switch to the off position or the on position for reselection. Note:
The manual selection function is only applicable to some models only.
When ice maker
does not operate
smoothly
Ice is lumped together
• When ice is lumped together, take the ice lumps out of the ice storage bin, break
them into small pieces, and then place them into the ice storage bin again.
• When the ice maker produces too small or lumped together ice, the amount of
water supplied to the ice maker need to adjusted. Contact the service center.
÷ If ice is not used frequently, it may lump together.
Power failure
• Ice may drop into the freezer compartment. Take the ice storage bin out and discard
all the ice then dry it and place it back. After the machine is powered again, crushed
ice will be automatically selected.
The unit is newly installed
• It takes about 12 hours for a newly installed refrigerator to make ice in the freezer
compartment.
Super freezer
Please select this function for prompt freezer.
ressin _PREss_z
• "On" or "Off" is repeated whenever p ,
g @
button.
EXPRESSFRZ
• The arrow mark graphic remains at the On
status when selecting Special Refrigeration "On".
• Super freezer function automatically turns off if a
fixed time passes.
Lock
This button stops operation of different
button.
LOCK
• Locking or Release
is repeated whenever
LOCK
pressing the (_ .
• Pressing the other button when selecting 'LOCK',
the button does not operate.
Ex) In selecting
"LOCK....
Ex) In selecting
UNLOCK"
The other
functions
Door open warning
• 3 times of warning sounds at the interval of 30 seconds if a minute passes with the
door of refrigerator and the hombar door opened or completely closed.
• Pleasecontact with the local service center if warning continue to sound even after
closing the door.
Diagnosis (failure detection) function
• Diagnosisfunction automatically detects failurewhen failure is found in product during
the use of refrigerator.
• If failure occurs at product, it does not operate though pressing any button and normal
indication is not done. In this case, do not turn power off but immediately contact with
the local service center. A lot of time are need for service engineer to detect the failed
part if turning it off.
How ice/cold
water
is supplied
How to use
dispenser
Water is cooled while stored in the water tank in the refrigerator compartment, and
then sent to the dispenser.
Ice is made in the automatic ice maker and sent to the dispenser divided into crushed
or cubed form ice.
• Select one among crushed ice, water, and cubed ice and slightly press the push
switch with a glass or other container.
Water
Light the water
indicating lamp by
pressing the selection
button.
• Water will be dispensed
by pressing the push
switch with a glass.
DISPENSER
Crushed ice
Light the crushed ice
indicating
lamp by
pressing the selection
button.
• Crushed icewill be
dispensedby pressingthe
pushswitch with a glass.
D,SPE,SER
L
Cubed ice
Light the cubed ice
indicating lamp by
pressing the
selection button.
• Cubedicewill be dispensed
by pressing the push
switch with a glass.
DISPENSER
6 Filter condition
(filter replacement
cycle) display
function
Cautions
• After 6 months, the following sentence and
will appear on the filter condition
part of the LEE). "Press for 3 seconds after replacing filter"
• After 6 months have passed, and if the filter has been replaced or you want to reset
the filter condition display, press the filter replacement button for more than 3
seconds and it will reset to the initial Power On state.
Throw away the ice (about 20 pieces) and water (about 7 glasses) first made
after refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or feed
water box. This is necessary in case that the refrigerator has not been used for a long
time.
Keep children away from the dispenser.
Children may push switch incorrectly bad or damage lamps.
Be careful that food is not block the ice
passage.
If foods are placed at the entrance of ice
passage, ice may not be dispensed. The ice
passage may also be covered with ice
powder if splinter ice is used only. This time,
remove the ice powder accumulated.
Freezer
door
Never store beverage cans or other
foods in ice storage bin for the purpose
of rapid cooling.
Such actions may damage the automatic ice maker.
Never use thin crystal glass or crockery to collect ice.
Such glasses or containers may be broken.
Put ice first into a glass before filling water or other beverages.
Water may be splashed if ice is added to existing liquid in a glass.
Never touch a hand or other tools on ice outlet.
Touch may cause a part breakage or hand injury.
Never remove the ice maker cover.
Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice is piled up just near the ice maker. So, such status may be considered, by the ice
maker, that the ice storage bin is fully filled and ice making operation may stop,
If discolored ice is dispensed, immediately contact service center, stopping use.
Never use too narrow or deep glass.
Ice may be jammed in ice passage and, thus, the refrigerator may be failed.
Keep the glass at a proper distance from ice outlet.
A glass too close to the outlet may hinder ice from coming out.
Shelf (Applicableto somemodelsonly)
Silde-Under
Shelf
You can store taller items such as a gallon container or bottles by simply pushing
in Fronthalf of shelf underneath back half of shelf. Pull toward you to return to a
FullshelF.
Wine holder
(Applicableto somemodelsonly)
Wine holder
adjustment
Bottles can be stored laterally with this wine corner. This can be attached to any
shelf,
)
In case of inserting the wine holder :
Pull the wine holder downward as in
!®
® aRer inserting it into the side anchoring
part of the shelf as in 0 by catching it
upward as in ¢.
In case of separating the wine holder :
Pull the wine holder inward as in @ after
holding it upward as in ® by catching it.
l®
Egg box
You can move the egg box to a place you want and select another form of box
according to the amount of eggs.
[Normal]
[For Many Eggs]
Humidity control in the vegetable compartment
The humidity carl be controlled by adjusting the humidity control switch to the
left/right when storing vegetabes or fruits.
High humidity
I
Close I ..........
_..........
0 Open
Low humidity
Convert into a vegetable or meat compartment
• The bottom drawer in the refrigerator can be converted into a vegetable or meat
compartment
0
Meats
Vegetables
,
Vegetable
compartment
.0
Meats
Vegetables
Meat compartment
The meat compartment maintains the temperature at a lower point than the
refrigerator compartment so that meat or fish can be stored fresh longer.
Deodorizer
(Applicableto somemodelsonly)
This system efficiently absorbs strong odors
by using the optical catalyst. This system
does hot have any affect on stored rood.
f=i
J_
./I
./
./
Deodorizing
system
Vegetable
I
I
compartment
tl
How to use the
deodorizing
system
COrnVersion
• Since it is installed already installed onto the cool air intake duct from the from
the refrigerator compartment, you need no separate installation,
• Pleaseuse closed containers to store food with pungent odors,
Otherwise, this oder can be absorbed by other food in the compartment,
Location
of foods
(Refer to identification of parts)
Wine holder
Snack
Store wine.
drawer
Store small foods such as bread, snacks, etc..
Freezer
Store various frozen foods such as meat, fish,
ice cream, frozen snacks, etc..
compartment
shelf
Freezer
compartment
door rack
Freezer
compartment
drawer
Milk product
corner
Egg box
• Store small packed frozen food.
• Temperature is likely to increase as door
opens. So, do not store long-term rood such
ice cream, etc..
• Store meat, fish, chicken, etc.. after
wrapping them with thin foil.
• Store dry.
Store milk products such as butter, cheese,
etc..
Place this egg box in the proper location.
Refreshment
center
Store foods of frequent use such as beverage,
etc,,
Refrigerator
compartment
shelf
Store side dishes or other foods at a proper
distance.
Refrigerator
compartment
door rack
Store small packed rood or beverages such
as milk,juice, beer, etc..
Vegetable
drawer
Vegetable
drawer
/meat drawer
conversion corner
Store vegetables
or fruits.
Store vegetable, fruits, meat to thaw, raw
fish, etc.. setting the conversion switch as
necessary.
Be sure to check the conversion switch
setting before storing foods.
Storing foods
• Store fresh food in the refrigerator compartment. How food is frozen and thawed is an
important factor in maintaining its freshness and flavor.
• Do not store rood which goes bad easily at low temperatures, such as bananas, and
melons.
• Allow hot rood to cool prior to storing, placing hot rood in the refrigerator could spoil
other rood, and lead to higher energy consumption.
• When storing the rood, cover it with vinyl wrap or store in a container with a lid. This
prevents moisture from evaporating, and helps rood to keep its taste and nutrients.
• Do not block air vents with rood. Smooth circulation of chilled air keeps refrigerator
temperatures even.
• Do not open the door frequently. Opening the door lets warm air enter the refrigerator,
and cause temperatures to rise.
• Never keep too much rood in door rack because they may push against by inner racks
so that the door cannot be fully closed.
Freezer
compartment
• Do not store bottles in the freezer compartment - they may break when frozen.
• Do not refreeze rood that has been thawed. This causes loss of taste and nutrient.
• When storing frozen food like ice cream for a long period, place it on the freezer
shelf, not in the door rack.
• Do not touch the cold foods or containers- especially made of metallic -, with wet
hands and place glass products in the freezer compartment.
- That'swhy you may have chilblainsand they may be broken when their inner matters
are frozen, causing personal injury,
Refrigerator
compartment
• Avoid placing moist food in top refrigerator shelves, it could freeze from direct
contact with chilled air.
• Always clean food prior to refrigeration. Vegetables and fruits should be washed and
wiped, and packed food should be wiped, to prevent adjacent food from spoiling.
• When storing eggs in their storage rack or box, ensure that they are fresh, and always
store them in an upright position, which keeps them fresh longer,
How to dismantle parts
Freezer
compartment
lamp
Dispenser
lamp
Freezer
compartment
shelf
Door rack and
support
Ice storage
bin
Separatethe lamp by pulling it out (®)while
slightlystriking((1))and rotating ((9)the lamp
cover,
Turn the bulb counterclockwise,Max. 40 W bulb
for refrigerator is used and can be purchased at
a service center.
Seperate the lamp by pulling it out, and then
remove the lamp. Max. 15 W bulb for
refrigerator is used and can be purchased at a
service center.
©
To remove a shelf, lift the left part of the shelf
a bit, push it to the direction (O), lift the right
part to the diretion (®), and take it out.
Lift the door rack holding both sides ((b) and
pull it out to (®) direction.
Hold the ice storage bin as shown in the right
figure and pull it out (®) while slightly lifting it
(®).
• It is recommended not to dismantle the ice
storage bin unless it is necessary.
• Be sure to use both hands when removing
the ice storage bin, so as not to drop it on the
floor.
• If the ice storage bin does not fit well, slightly
rotate the rotating device.
Rotating
device
After dispenser
is used
The water collector has no self-drainage
function. So it should be cleaned regularly.
Remove the cover by pressing the left side of
water collector cover and dry it with a cloth.
Press the point marked as shown in the figure
to the right to remove the water collector
cover.
Lamp in
refrigerator
compartment
To remove the lamp cover, press the protrusion under the lamp cover to the front and
then pull the lamp cover out.
Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can be
purchased at a service center.
Vegetable
compartment
cover
• To remove the vegetable compartment
cover, pull out the vegetable compartment
a bit to the front (b, lift the front part of the
vegetable compartment cover as shown by
@, and take it out.
®
General information
Vacation
time
During average length vacations, you will probably find it best to leave the refrigerator
in operation. Placefreezable items in freezer for longer life.
When you plan not to operate, remove all food, disconnect the power cord, clean the
interior thoroughly, and leave each door OPEN to prevent odor formation.
Power failure
Most power failures that are corrected in an hour or two will not affect your
refrigerator temperatures.
However, you should minimize the number of door openings while the power is off.
If you move
Remove or securely fasten down all loose items inside the refrigerator.
To avoid damaging the height adjusting screws, turn them all the way into the base.
Anti
condensation
pipe
The outside wall of the refrigerator cabinet may sometimes get warm, especiallyjust
after installation.
Don't be alarmed. This is due to the anti-condensation pipe, which pumps hot
refrigerator to prevent "sweating" on the outer cabinet wall.
Cleaning
It is important that your refrigerator be kept clean to prevent undesirable odors. Spilled
rood should be wiped up immediately, since it may acidify and stain plastic surfaces if
allowed to settle.
After
Exterior
Use a lukewarm solution of mild soap or detergent to clean the durable finish of your
refrigerator.
Wipe with a clean damp cloth and then dry.
Interior
Regular cleaning is recommended. Wash all compartments a baking soda solution or a
mild detergent and warm water. Rinse and dry.
cleaning
Please verify that the power cord is not damaged, power plug is not overheated, or
power plug is well inserted into the power consent.
Warning
Always remove power cord from the wall outlet prior to cleaning in the vicinity of
electrical parts (lamps, switches, controls, etc.).
Wipe up excess moisture with a sponge or cloth to prevent water or liquid from
getting into any electrical part and causing an electric shock.
Never use metallic scouring pads, brushes, coarse abrasive cleaners, strong alkaline
solutions, flammable or toxic cleaning liquids on any surface.
Do not touch frozen surfaces with wet or damp hands, because damp object will stick
or adhere to extremely cold surfaces.
Trouble shooting
Before calling for service, review this list. It may save you both time and expense,
This list includes common occurrences that are not the result of defective
workmanship or materials in this appliance.
Runing of
refrigerator
Refrigerator
compressor
does not run.
Refrigerator
runs too much
or too long
Refrigerator control is off.
Set refrigerator control. See setting the
controls.
Refrigerator is in defrost cycle.
This is normal for a fully automatic
defrosting refrigerator. The defrost
cycle occurs periodically.
Plug at wall outlet is disconnected.
Make sure plug is tightly pushed into
outlet.
Power outage. Check house lights.
Call local electric company.
Refrigerator is larger than the previous
one you owned,
This is normal. Larger, more efficient
units run longer in these conditions.
Room or outside weather is hot.
It is normal for the refrigerator to work
longer under these conditions.
Refrigerator has recently been
disconnected for a period of time.
It takes some hours for the refrigerator
to cool down completely.
Large amounts of warm or hot food
may have been stored recently,
Warm food will cause the refrigerator to
run longer until the desired temperature
is reached.
Doors are opened too frequently or too
long.
Warm air entering the refrigerator
causes it to run longer. Open the door
less often.
Refrigerator or freezer door may be
slightly open.
Make sure the refrigerator is level.
Keep food and containers from
blocking door. See problem section.
OPENING/CLOSING of doors.
Refrigerator control is set too cold.
Set the refrigerator control to a
warmer setting until the refrigerator
temperature is satisfactory.
Refrigerator or freezer gasket is dirty,
worn, cracked, or poorly fitted,
Clean or change gasket. Leaks in the
door seal will cause refrigerator to run
longer in order to maintain desired
tern peratures.
Thermostat is keeping the refrigerator
at a constant temperature,
This is normal. Refrigerator goes on and
off to keep the temperature constant,
Refrigerator
compressor
does not run.
Thermostat is keeping the refrigerator
at a constant temperature,
This is normal. The refrigerator goes on
and offto keep the temperature constant,
Freezer control is set too cold
Set the Freezercontrol to a warmer
setting until the Freezertemperature is
satisfactory.
Refrigerator control is set too cold.
Set the refrigerator control to a
warmer setting
Refrigerator control is set too cold.
See above solution.
Temperatures
are
too cold
Temperature in the
freezer is too cold
but the refrigerator
temperature is
satisfactory.
Temperature in the
refrigerator is too
cold and the freezer
temperature
is satisfactory.
Food stored in
drawers freezes.
Meat stored in
fresh meat
drawer freezes.
Meat should be stored at a temperature
just below the freezingpoint of water (32°F,
OC) for maximum fresh storage time.
It is normal For ice crystals to Form due
to the moisture content of meat.
Temperatures
are too warm
Temperatures in
the refrigerator
or freezer are
too warm.
Temperature in the
refrigerator
is too warm but
the freezer
temperature is
satisfactory.
Freezer control is set too warm.
......
ReFrigeratorcontrol is set too warm.
Refrigerator control has some effect on
freezer temperature,
Set the Freezeror refrigerator control to
a colder setting until the Freezeror
refrigerator temperature is satisfactory.
Set the freezer or refrigerator control to a
colder setting until the freezer or
refrigerator temperature is satisfactory.
Doors are opened too Frequently or too
long.
Warm air enters the refrigerator/freezer
whenever the door is opened.
Open the door less often.
Door is slightly open.
Close the door completely.
Large amounts of warm or hot food
may have been stored recently,
Wait until the refrigerator or freezer
has a chance to reach its selected
temperature.
Refrigerator has recently been
disconnected for a period of time.
A refrigerator requires some hours to
cool down completely.
Refrigerator control is set too warm.
Set the refrigerator control to a colder
setting.
Sound
and noise
Louder sound
levelswhen
refrigerator is on.
Today's refrigerators have increased
storage capacity and maintain more
even temperatures.
It is normal for sound levels to be higher.
Louder sound
levels when
compressor
comes on.
Refrigeratoroperates at higher pressures
during the start of the ON cycle,
This is normal. The sound will level off as
the refrigerator continues to run.
Vibrating or
rattling noise.
Floor is uneven or weak.
Refrigerator rocks on the floor when it is
moved slightly.
Be sure floor is level and solid and can
adequately support refrigerator.
Items placed on the top of the refrigerator
are vibrating.
Remove items.
Dishes are vibrating on the shelves in
the refrigerator.
It is normal for dishes to vibrate slightly.
Move dishes slightly.
Make sure refrigerator is level and firmly
set on floor.
Refrigerator is touching wall or cabinets.
Move refrigerator so that it does not
touch the wall or refrigerator.
The weather is hot and humid which
increases the rate of frost buildup
and internal sweating.
This is normal.
Door is slightly open.
See problem section opening/closing of
doors.
Door is opened too often or too long.
Open the door less often.
Weather is humid.
This is normal in humid weather.
When humidity is lower, the moisture
should disappear.
Door is slightly open,causing cold air
from the inside the refrigerator to meet
warm air from the outside.
This time, close the door completely.
Water/Moisture
/Ice inside
refrigerator
Moisture collects
on the inside walls
of the refrigerator,
Water/Moisture
/Ice outside
refrigerator
Moisture forms
on the outside of
the refrigerator
or between doors.
Odors in refrigerator
Interior needs to be cleaned.
Clean interior with sponge,warm water
and baking soda.
Food with strong odor is in the refrigerator.
Cover rood completely.
Some containers and wrapping materials
produce odors,
Use a different container or brand of
wrapping materials.
Food package is keeping door open.
Move packages that keep door from
closing.
Door was closed too hard, causing other
door to open slightly.
Close both doors gently.
Refrigerator is not level. It rocks on the
floor when it is moved slightly.
Adjust the height adjusting screw.
Floor is uneven or weak.
Refrigerator rocks on the floor when it
is moved slightly.
Be sure floor is level and can adequately
support refrigerator.
Contact carpenter to correct sagging or
sloping floor.
Refrigerator is touching wall or cabinets.
Move refrigerator..
Food is touching shelf on top of the
drawer
Keep less rood in drawer.
Track that drawer slides on is dirty.
Clean drawer and track.
Ice storage bin is empty.
When the first supply or ice is dropped
into the bin, the dispenser should operate,
Freezer temperature is set too warm.
Turn the freezer control to a higher
setting so that ice cubes will be made,
When the first supply of ice is made,
the dispenser should operate.
Household water line valve is not open.
Open household water line valve and
allow sufficient time Forice to be made.
When ice is made, dispenser should
operate.
Refrigerator or freezer door is not closed.
Be sure both doors are closed.
Opening/Closing of
doors/Drawers
Door(s) will not
close,
Door(s) will not
close,
Drawers are
difficult to move.
Dispenser
Dispenser will not
dispense ice
Dispenserwill
IcehasmeltedandFrozen
around
auger Remove
icestorage
bin,andthawand
not dispense
ice.
due to infrequent use, temperature
Fluctuations and/or power outrages,
the contents. Clean bin, wipe dry and
replace in proper position.
When new ice is made, dispenser should
operate.
Ice dispenser
is jammed,
Ice cubes arejammed between the ice
maker arm and back oFthe bin.
Remove the ice cubes that arejamming
the dispenser.
Ice cubes are Frozentogether.
Use the dispenser often so that cubes do
not Freezetogether.
Ice cubes that have been purchased or
made in some other way have been
used in the dispenser.
Only the ice cubes made by the ice maker
should be used with the dispenser.
Household water line valve is not open.
See problem "Ice maker is not making
any ice."
Open household water line valve.
ReFrigeratoror Freezer door is not closed.
Be sure both doors are closed.
Water has been in the tank Fortoo long.
[)raw and discard 7 glasses oFwater
to Freshenthe supply. [)raw and discard
an additional 7 glasses to completely rinse
out tank.
Unit not properly connected to cold
water line.
Connect unit to cold water line which
supplies water to kitchen Faucet.
Dispenser will
not dispense
water,
Water has an
odd taste
and/or odor.
Sound of ice
dropping
Sound of water
supply
Other
This sound is normally made when automatically made ice is dropped into ice storage
bin. Volume may vary according to refrigerator's location.
This sound is normally made when ice maker is supplied with water after dropping
the automatically made ice.
Pleasethoroughly read 'Automatic ice maker and dispenser' in this manual.
LG Electronics
Inc.
LG Twin Tower, 20, Yoido-Dong,
Youngdungpo-Gu, Seoul, 150-721, Korea.
http://www.lge.com
P/NO : 3828JD8792G
Printed in Korea
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising