ACD-15 PRO
Data Sheet
ACD-15 PRO
2000A Clamp-on Multimeter
Wide range of measuring features built into one, professional meter.
■■ Measurements:
AC/DC Voltage
up to 600V, AC Current up to
2000A, Resistance, Frequency
and Capacitance
■■ Non-contact
Voltage Level
Detection
■■ Audible
continuity
■■ Auto-check
feature
automatically selects DCV,
ACV or Resistance (W)
■■ Auto
and manual ranging
■■ Auto
power off
■■ Automatic
■■ Low
polarity
battery indication
■■ Data
hold
■■ Large,
easy to read digital
LCD display
■■ Accommodates
conductors up to
45mm (1.77”) in diameter
■■ Carrying
case, test leads, batteries
(installed) and manual included
■■ Voltage
overload protection for all
functions up to 600V AC/DC
No hassle
warranty
No waiting.
No shipping
charges.
Our commitment to
high-quality products
and customer service
is demonstrated by
our industry exclusive
“No Hassle” warranty.
In the unlikely event
that an Amprobe Test
Tool requires warranty
service, any of our
local dealers are
authorized to replace
it, on the spot.
(note: $500 MSLP limit)
600V
Amprobe® Test Tools
www.Amprobe.com
Data Sheet
ACD-15 PRO 2000A Digital Clamp-on Multimeters
Electrical Specifications
Accuracy is ±(% reading digits + number of digits) or otherwise specified, at 23 ℃ ±5 ℃ and less than 75% R.H.
Function DC Voltage
NMRR : CMRR : Hi-Z DCV Input Impedance: AutoCheck™ Lo-Z DCV input impedance: AutoCheck™ DCV Threshold:
AC Voltage
50Hz / 60Hz
50Hz ~ 500Hz
CMRR: Hi-Z ACV Input Impedance: AutoCheck™ Lo-Z ACV input impedance: AutoCheck™ ACV Threshold: Resistance
Open Circuit Voltage: 0.4VDC typical 600W with Continuity Beeper
Continuity Beeper Response: Open Circuit Voltage: Audible Threshold: Frequency
Range
10Hz ~ 30kHz 0Hz ~ 1kHz 10Hz ~ 1kHz Accuracy: Max display: Amprobe® Test Tools
Range Accuracy
6.000V 0.5% + 3d
60.00V 1.0% + 5d
600.0V 2.0% + 5d
>30dB @ 50/60Hz
>100dB @ DC, 50/60Hz, Rs=1kW
5MW, 90pF nominal
Initially 1.6kW, 90pF nominal; Impedance increases significantly as display voltage
increases from 50V (typical). Typical impedances vs display voltages for reference are:
15kW @ 100V; 100kW @ 300V; 210kW @ 600V
> +1.5VDC or < -1.0VDC nominal
6.000V, 60.00V 1.5% + 5d
600.0V 2.0% + 5d
6.000V, 60.00V 2.0% + 5d
600.0V 2.5% + 5d
>60dB @ DC to 60Hz, Rs=1kW
5MW, 90pF nominal
Initially 1.6kW, 90pF nominal; Impedance increases significantly as display voltage
increases from 50V (typical). Typical impedances vs display voltages for reference are:
5kW @ 100V; 100kW @ 300V; 210kW @ 600V
> 2VAC (50/60Hz) nominal.
1.2% + 6d 1) 3)
6.000kW 2) 60.00kW, 600.0kW 1.0% + 4d
6.000MW 2.0% + 4d
1) Cool down interval 2 minutes after over 50V measurements in Auto-VW position
2) Beeper on while reading < 0.025kW
3) Add 40d to specified accuracy while reading is
600.0W
2.0%+8d 1)
< 100µs
0.4VDC typical
between 10W and 300W 1) Add 40d to specified accuracy while reading is below
20% of range
Sensitivity (Sine RMS)
4V 30V 1
60V 0.5%+4d
9999 counts
Voltage Range
6.000V
60.00V
600.0V
www.Amprobe.com
Data Sheet
ACD-15 PRO 2000A Digital Clamp-on Multimeters
Function Range Accuracy
Diode Tester
Open Circuit Voltage Test Current
< 1.6 VDC 0.4mA (typical)
Audible Threshold: between 0.015V & 0.080V
Capacitance
100.0nF 2), 1000nF,
3.5%+5d 1) 3)
10.00µF, 100.0µF, 2000µF
1) Accuracies with film capacitor or better
2) Accuracy below 50nF is not specified
3) Specified with battery voltage above 2.8V (approxmately half full battery). Accuracy decreases gradually to 12% at low
battery warning voltage of approximately 2.4V
Non-Contact EF-Detection
Typical Voltage Bar Graph Indication
15V TO 85V 40V TO 130V - 60V TO 210V
-- 90V TO 300V --- ABOVE 120V ---- Indication: Bar graph segments & audible beep tones proportional to the field strength
Detection Frequency: 50/60Hz
Detection Antenna: Top side of the stationary jaw
Probe-Contact EF-Detection: For more precise indication of live wires, use the Red (+) probe for direct contact measurements
AC Current (Clamp-on)
50Hz / 60Hz
400.0A, 2000A 1.5% + 5d 1) 2) 3)
1) Add 8d to specified accuracy while reading is below 10% of range
2) Induced error from adjacent current-carrying conductor: < 0.06A/A
3) Specified accuracy is for measurements made at the jaw center. When the conductor is not positioned at the jaw center, position errors introduced are: Add 1% to specified accuracy for measurements made within jaw marking lines (away from jaw opening) Add 4%
to specified accuracy for measurements made beyond jaw marking lines (toward jaws opening)
www.Amprobe.com
ACD-15 PRO 2000A Digital Clamp-on Multimeters
Data Sheet
General Specifications
Display: Update Rate: Polarity: Low Battery: Operating Temperature: Relative Humidity: Altitude: Storage Temperature: Temperature Coefficient: Sensing: Safety: Transient Protection: Pollution Degree: E.M.C.: In an RF field of 3V/m: Overload Protections: Power Supply: Power Consumption: APO Timing:
APO Consumption: Dimension: Weight: Jaw opening & Conductor Diameter: 3-5/6 digits 6000 counts LCD display
5 per second nominal
Automatic
Below approx. 2.4V
0°C to 40°C
Maximum relative humidity 80% for temperature up to 31°C decreasing linearly to 50%
relative humidity at 40°C
Operating below 2000m
-20℃ to 60℃, < 80% R.H. (with battery removed)
nominal 0.15 x (specified accuracy)/℃ @(0℃ -18℃ or 28℃ -40℃), or otherwise specified
Average sensing
Meets EN61010-1:2001; IEC61010-2-032(1994), EN61010-2-032(1995), UL3111-2-032(1999).
Category III 600 Volts AC & DC
6.5kV (1.2/50µs surge) for all models
2
Meets EN61326-1
Capacitance function is not specified. Total Accuracy = Specified Accuracy + 45 digits
Performance above 3V/m is not specified
ACA Clamp-on jaws: AC 2000A rms continuous + & COM terminals (all functions):
600VDC/VAC RMS
standard 1.5V AAA Size (NEDA 24A or IEC LR03) battery X 2
2.2mA typical for ACD-15 PRO; 2.8mA typical for ACD-15 TRMS-PRO
Idle for 3 minutes
40µA typical on voltage & current functions
L224mm X W78mm X H40mm
220 gm approx
45mm max
Included Accessories
Test leads, carrying case and manual
Optional Accessories
ELS2A Line splitter (Energizer)
ACF-3000AK 3000A AC Flexible Clamp-On Attachment
TMA-K
Temperature Adapter
TL36A
Industry Test Leads with Threaded Alligator Clips
Amprobe® Test Tools
website: www.Amprobe.com
email: info@amprobe.com
Everett, WA 98203
Tel: 877-AMPROBE
Amprobe® Test Tools Europe
In den Engematten 14
79286 Glottertal, Germany
Tel.: +49 (0) 7684 8009 - 0
©2007 Amprobe Test Tools. All rights reserved.
9/2007 3128817 Rev A
Amprobe® Test Tools
www.Amprobe.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising