Product Data: Modal Exciter Types 4825 and 4826 (BP1937)

Product Data: Modal Exciter Types 4825 and 4826 (BP1937)
P R O D U C T D ATA
Modal Exciter Types 4825 and 4826
Modal Excitation System Types 3625 and 3626
Designed for demanding modal test applications, electrodynamic
Modal Exciter Types 4825 and 4826 provide precise, reliable, stable
and long-lasting operation. High quality materials, rugged
construction and stringent quality control assure versatile means of
modal excitation for any experimental modal test.
The two modal exciters are available as stand-alone units – supplied
only with the appropriate trunnion, blower and connecting cable – or
as complete systems (Types 3625 and 3626) with matching power
amplifiers and a standard set of stingers.
Optional accessories include traditional push/pull stingers, tension
wire stingers, robust lateral modal exciter stands, turnbuckles, hose
and cable extension kits, chuck nut assemblies and various adaptors.
Uses and Features
Uses
• General mechanical mobility measurements
• Experimental modal analysis using SISO, MISO, SIMO and
MIMO test techniques
• Advanced structural dynamics investigations
• Structural damage detection
• Finite element model correlation and validation
Features
• Force rating:
– 200 N sine (Type 4825)
– 400 N sine (Type 4826)
• 1-inch peak-to-peak displacement for best low-frequency
excitation
• Wide operating frequency range: DC – 5000 Hz
• Through-hole design for choice of tension wire stingers or
traditional push/pull stingers
• Rugged, industrial design
• High force-to-weight ratio due to rare earth magnet
technology
• High-rigidity, low-mass magnesium armature for minimized
force drop-offs at resonance frequencies
• Compact, light-weight construction enabling easy positioning/
orientation relative to test object
• Low stray magnetic field
• Ideal for any excitation signal (sine, impulse and random
signals)
• Built-in air switch for protection against damage related to
excessive current
• Built-in optical sensor for accurate determination of armature
position
• Electronic DC control of tension wire pre-tensioning (optional)
• Full range of stringers – tension wire technology or traditional
push/pull stringer technology (optional)
• Robust lateral exciter stands for easy positioning and
orientation (optional)
• Can be delivered as complete turnkey excitation systems:
Types 3625 and 3626
Description
The low-weight modal exciters feature small physical dimensions relative to their force ratings and a lowmass, high-rigidity spring-suspended armature. The light-weight armature helps to ensure high-quality
force measurements by minimizing force drop-offs at the test specimen’s resonance frequencies.
The “hole-through” design makes it possible to use tension wire stingers or traditional push/pull stingers
with the exciters. Easy and rapid attachment of stingers is achieved by use of a chuck nut assembly (for use
with tension wire stingers) or with an M6 to 10–32 UNF threaded insert (for use with push/pull stingers).
In lateral setups of Types 4825 and 4826, tension wire stingers can easily be mechanically pre-tensioned
with the use of a Lateral Modal Exciter Stand. For electrical pre-tensioning, especially useful in vertical,
skewed setups and for excitation in confined spaces, use DC Static Centring Unit Type 1056. The modal
exciters have a Video HR-10 socket that outputs the signal from the built-in optical sensor, providing
necessary feedback to the DC Static Centring Unit. Traditional push/pull stingers require no pre-tensioning.
220
306
180
ø200
ø10
M6
M6
10
10
M8
142.4
76
ø40
100
72.9
63
63
99.1
Fig. 1
Dimensions of
Modal Exciter
Types 4825 or 4826 in
its trunnion (in mm)
ø7
226
010125
Modal Excitation System Types 3625 and 3626
Types 3625 and 3626 are complete turnkey excitation systems comprising Modal Exciter Types 4825 and
4826 with trunnion and blowers, matching power amplifier, stingers and all necessary cables.
Modal Exciter Configurations
See Modal Exciter Configuration Guide (BG 1483) for an overview of modal excitation systems, exciter
stands, stingers, tension wires, and force and impedance transducers.
Compliance with Standards
Temperature
Humidity
2
The CE marking is the manufacturer's declaration that the product meets the requirements of the applicable EU
directives
RCM mark indicates compliance with applicable ACMA technical standards – that is, for telecommunications, radio
communications, EMC and EME
China RoHS mark indicates compliance with administrative measures on the control of pollution caused by electronic
information products according to the Ministry of Information Industries of the People’s Republic of China
WEEE mark indicates compliance with the EU WEEE Directive
IEC 60068–2–1 & IEC 60068–2–2: Environmental Testing. Cold and Dry Heat.
Operating Temperature: 5 to + 40 °C (41 to 104 °F)
Storage Temperature: –25 to +70 °C (–13 to +158 °F)
IEC 60068–2–78: Damp Heat: 90% RH (non-condensing at 40 °C (104 °F)).
Specifications – Modal Exciter Types 4825 and 4826
Table 1 Specifications for Modal Exciter Types 4825 and 4826 in system configurations
Type 4825/3625
Type 4826/3626
Matching Power Amplifier
Type 2720
Type 2721
Matching Blower
UH-1035
UH-1036
Rated Force – without forced air cooling [sine (peak)/random (RMS)]
100/70 N
100/70 N
Rated Force – with forced air cooling [sine (peak)/random (RMS)]
*
200/140 N
400/280 N*
Useful Frequency Range
2 – 5000 Hz
2 – 5000 Hz
Operating Frequency Range
DC – 5000 Hz
DC – 5000 Hz
Max. Rated Travel
25.4 mm (1 in)
25.4 mm (1 in)
Max. Velocity [sine (peak)/random (RMS)]
Max. Acceleration [sine (peak)/random (RMS)]
1.5/1.5 m/s
1.5/1.5 m/s
863/608 m/s2 (88/62 g)
981/697 m/s2 (100/71 g)
11.2 A
18 A
4 N/mm
4 N/mm
Rated Current
Suspension Stiffness
Effective Moving Mass
Main Resonance Frequency
Weight with Trunnion
0.23 kg
0.40 kg
>6000 Hz
4000 Hz
21 kg (46 lb)
21 kg (46 lb)
* Brüel & Kjær assumes no responsibility if blowers other than UH-1035 or UH-1036 are used for cooling
Table 2 Specifications for Blowers UH-1035 and UH-1036
UH-1035
UH-1036
Mains
Power
Frequency
Max.
Air
Capacity
Max.
Diff. Pressure
(Vacuum)
Electromotor
Hose
diameter
50 Hz
80 m3/hr.
110 hPa
0.37 kW
60 Hz
90 m
3/hr.
130 hPa
0.45 kW
50 Hz
140 m3/hr.
150 hPa
1.1 kW
60 Hz
3/hr.
180 hPa
1.3 kW
175 m
SPL
Weight
Approx.
Dimensions
Enclosure
40 mm
(1.6 in)
58 dB(A)
10 kg
(22.0 lb)
248 × 230 × 250 mm
(9.8 × 9.1 × 9.8 in)
IP class 54
40 mm
(1.6 in)
63 dB(A)
16 kg
(35.3 lb)
287 × 241 × 305 mm
(11.3 × 9.5 × 12.0 in)
IP class 54
61 dB(A)
64 dB(A)
Ordering Information
Modal Exciters
Modal Excitation Systems
Type 4825
Modal Exciter
includes the following:
• AQ-0649: Cable with two 4-pin Neutrik® speakON® plugs,
length 5 m (16.4 ft)
• KC-1007: Trunnion
• UH-1035: 200 N Blower
• AF-1101: Air Hose for UH-1035, 5 m (16.4 ft)
• UA-1612: Three Adaptors M6 to 10–32 UNF
Type 3625
Modal Excitation System
includes the following:
• Type 4825: Modal Exciter
• Type 2720: Power Amplifier (500 VA)
• UA-1598: Three Push/Pull Steel Stingers with:
– 3 × fastening screws
– 3 × adaptors, diameter 2.5 mm to 10–32 UNF
– 3 × steel rods, length 500 mm, diameter 2.5 mm
– 1 × 2.5 mm collet chuck (chuck nut with collet insert)
Type 4826
Modal Exciter
includes the following:
• AQ-0659: Cable with two 8-pin Neutrik speakON plugs,
length 5 m (16.4 ft)
• KC-1007: Trunnion
• UH-1036: 200 N Blower
• AF-1103: Air Hose for UH-1036, length 5 m (16.4 ft)
• UA-1612: Three adaptors, M6 to 10–32 UNF
Type 3626
Modal Excitation System
includes the following:
• Type 4826: Modal Exciter
• Type 2721: Power Amplifier (1250 VA)
• UA-1598: Three Push/Pull Steel Stingers, with:
– 3 × fastening screws
– 3 × adaptors, diameter 2.5 mm to 10–32 UNF
– 3 × steel rods, length 500 mm, diameter 2.5 mm
– 1 × 2.5 mm collet chuck (chuck nut with collet insert)
3
Optional Accessories
UA-1603
ELECTRICAL TENSION WIRE PRE-TENSIONING
Type 1056
DC Static Centring Unit
POWER AMPLIFIERS
Type 2720
Power Amplifier (500 VA)
Type 2721
Power Amplifier (1250 VA)
UA-1606
FORCE TRANSDUCERS AND IMPEDANCE HEAD
Type 8230
CCLD Force Transducer (+44/–44 N range)
Type 8230-001
CCLD Force Transducer (+220/–220 N range)
Type 8230-002
CCLD Force Transducer (+2200/–2200 N range)
Type 8230-003
CCLD Force Transducer (+22000/–2200 N range)
Type 8230-C-003 Charge Force Transducer (+22200/–2200 N range)
Type 8231-C
Charge Force Transducer (+110000/–2200 N range)
Type 8203
Force Transducer/Impact Hammer
Type 8001
Impedance Head
THREAD AND BUSHING ADAPTORS
UA-2052
Set of 10 Stud Adaptors, 10–32 UNF to ¼–28 UNF
UA-2054
Set of 20 Bushing Adaptors, 10–32 UNF to
¼–28 UNF
CABLE AND HOSE EXTENSIONS
AQ-0648
Extension Cable with Neutrik speakON 4-pin
connector at both ends, length 10 m
AQ-0655
Extension Cable with Neutrik speakON 8-pin
connector at both ends, length 10 m
AF-1102
Extension Air Hose, length 10 m
AQ-0658
Extension Cable with 9-pin D-sub connector to
video HR-10 connector
LATERAL MODAL EXCITER STANDS
UA-1607
Modal Exciter Stand, height 1.4 m
Mechanical pre-tensioning of tension wire possible
via adjustable spring
UA-1608
Modal Exciter Stand, height 2.0 m
Mechanical pre-tensioning of tension wire possible
via adjustable spring
TRADEMARKS
Neutrik and speakON are registered trademarks of Neutrik AG
Brüel & Kjær reserves the right to change specifications and accessories without notice. © Brüel & Kjær. All rights reserved.
Brüel & Kjær Sound & Vibration Measurement A/S
DK-2850 Nærum · Denmark · Telephone: +45 77 41 20 00 · Fax: +45 45 80 14 05
www.bksv.com · info@bksv.com
Local representatives and service organisations worldwide
ËBP-1937---]Î
BP 1937 – 14
2014-08
STINGERS, TENSION WIRES AND ACCESSORIES
UA-1596
Five 2.5 mm Push/Pull Steel Stingers, including:
• 10 × adaptors, diameter 2.5 mm to 10–32 UNF
• 5 × steel rods, length 200 mm, diameter 2.5 mm
• 10 × fastening screws
UA-1597
Five 3.0 mm Push/Pull Steel Stingers, including:
• 10 × adaptors, diameter 3.0 mm to 10–32 UNF
• 5 × steel rods, length 200 mm, diameter 3.0 mm
• 10 × fastening screws
UA-1598
Three 2.5 mm Push/Pull Steel Stingers, including:
• 3 × fastening screws
• 3 × adaptors, diameter 2.5 mm to 10–32 UNF
• 3 × steel rods, length 500 mm, diameter 2.5 mm
• 1 × 2.5 mm collet chuck (chuck nut with collet insert)
UA-1599
Three 3.0 mm Push/Pull Steel Stingers, including:
• 3 × fastening screws
• 3 × adaptors, diameter 3.0 mm to 10–32 UNF
• 3 × steel rods, length 500 mm, diameter 3.0 mm
• 1 × 3.0 mm collet chuck (chuck nut with collet insert)
UA-1600
One 0.75 mm Tension Wire, length 5000 mm,
including:
• 1 × fastening screw
• 1 × adaptor, diameter 0.75 mm to 10–32 UNF
• 1 × 0.75 mm collet chuck (chuck nut with collet
insert)
UA-1601
Three 1.5 mm Tension Wires, length 500 mm,
including:
• 3 × fastening screws
• 3 × adaptors, diameter 1.5 mm, 10–32 UNF
• 3 × 1.5 mm collet chucks (chuck nut with collet
insert)
UA-1602
Three 0.75 mm Collet Chucks and Adaptors, for tension
wire, including:
• 3 × chuck nuts
• 3 × collet inserts, diameter 0.75 mm
• 3 × fastening screws
• 3 × adaptors, diameter 0.75 mm to 10–32 UNF
UA-1604
Three 1.5 mm Collet Chucks and Adaptors, for
tension wire, including:
• 3 × chuck nuts
• 3 × collet inserts, diameter 1.5 mm
• 3 × fastening screws
• 3 × adaptors, diameter 1.5 mm to 10–32 UNF
Three 2.5 mm Collet Chuck and Adaptor, for
push/pull rod, including:
• 3 × chuck nuts
• 3 × collet inserts, diameter 2.5 mm
• 3 × fastening screws
• 3 × adaptors, diameter 2.5 mm to 10–32 UNF
Five 3.5 mm Nylon Stingers, including:
• 5 × nylon rods, length 200 mm, diameter 3.5 mm
• 10 × fastening screws
• 10 × adaptors, diameter 3.5 mm to 10–32 UNF
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising