+MCX for pdf
E
IN G
L LO
N
O TA
A
C
MCX Miniature
Coaxial Connectors
APPLIED ENGINEERING PRODUCTS
104 John W. Murphy Drive • P.O. Box 510 • New Haven, CT 06513
(203) 776-2813 • FAX (203) 776-8294
www.aepconnectors.com • e-mail: aepsales@aepconnectors.com
MCX Miniature Coaxial Connectors
Mating Interfaces
Plug interface dimensions
Jack interface dimensions
Reference Plane
D
Reference Plane
D
E
20˚
E
øA
øI
øC
øC
B
H
F
K
K
F
B
Dimension Min. inches (mm) Max. inches (mm)
A
*
*
B
.006 (0,15)
—
C
.018 (0,48)
.021 (0,53)
D
.163 (4,15)
—
E
—
.029 (7,4)
F
.110 (2,80)
.126 (3,20)
H
—
.012 (0,30)
I
.079 (2,00)
—
K
.110 (2,80)
—
*Dimension to meet engagement and disengagement forces.
Specifications
øA
øH øI
Dimension
A
B
C
D
E
F
H
I
K
Min. inches (mm)
.142 (3,60)
.000
.150 (3,80)
.157 (4,00)
.030 (0,75)
.091 (2,3)
.135 (3,42)
—
.102 (2,60)
Max. inches (mm)
.148 (3,75)
—
—
.162 (4,12)
.033 (0,85)
.110 (2,80)
.137 (3,48)
.078 (1,98)
.110 (2,80)
(MIL-PRF-39012 as applicable)
Materials:
Plug spring fingers, female center contacts: Beryllium copper per ASTM B196, Condition HT.
Crimp sleeves: Seamless copper tube per ASTM B75, type C12000, temper: light anneal 050.
Other metal parts: Brass per ASTM B16, Alloy 360, 1⁄ 2 hard.
Insulators: Teflon (TFE) per ASTM D1710.
Finish:
Center contacts: Gold plated per MIL-G-45204 Type II, Class 0, Grade C, over .00010 to .00020
sulfamate nickel per QQ-N-290.
Other metal parts: Gold or nickel plated to meet MIL-PRF-39012 corrosion requirements.
Mechanical:
Force to engage: 6 pounds max.
Force to disengage: 1.8 pounds min.
Contact retention: 2.3 pounds min axial force.
Durability: 500 mating cycles.
Electrical:
Impedance: 50Ω.
Frequency range: DC–6 GHz.
Voltage Rating: 250VRMS (RG-178 cable); 335 VRMS (RG-316 cable).
Insulation Resistance: 1,000 megohms minimum.
Contact Resistance:
Center contact: 5.0 milliohms maximum.
Outer contact: 2.5 milliohms maximum.
VSWR:
Frequency
Straight connector
Right angle connector
1 GHz
1.22:1 max.
1.35:1 max.
6 GHz
1.35:1 max.
1.50:1 max.
Environmental (MIL-STD-202):
Temperature range: -65˚ C to +165˚ C.
Thermal shock: Method 107, condition C.
Corrosion: Method 101, condition B, 5% salt solution.
Vibration (Method 204): Condition D.
Moisture resistance: Method 106.
Contents
Right Angle Cable Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Straight and Right Angle P. C. Board Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Assembly Instructions and Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About AEP; other AEP Product LInes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4
5
6
APPLIED ENGINEERING PRODUCTS
104 John W. Murphy Drive • P.O. Box 510 • New Haven, CT 06513
(203) 776-2813 • FAX (203) 776-8294
www.aepconnectors.com • e-mail: aepsales@aepconnectors.com
2
MCX Miniature Coaxial Connectors
Click on part number to go directly to cable assembly instructions
Right Angle Cable Plugs
Crimp type for flexible cable
.321 (8,2)
.243 (6,2)
.156
(4,0)
.165 (4,2)
.234
(5,9)
.437
(11,1)
.344
(8,7)
ø.122 (3,1)
øA
CABLE TYPES
RG178, RG196, M17/93, M17/169
RG174, RG316, M17/113,
M17/119, M17/172, M17/189
Dim. A
.040 (1,0)
AEP P/N
8955-1521-002
.067 (1,7)
8955-1521-003
Direct solder for semi-rigid cable
D
E
G
F
C
B
øA
CABLE TYPES
.085" semi-rigid, RG405, M17/133
.141" semi-rigid, RG402, M17/130
Dim. A Dim. B
.089 (2,3) .210 (5,3)
.144 (3,1) .242 (6,1)
APPLIED ENGINEERING PRODUCTS
(203) 776-2813 • FAX (203) 776-8294
Dim. C
.303 (7,7)
.335 (8,5)
Dim. D
.321 (8,2)
.359 (9,1)
Dim. E
.243 (6,2)
.266 (6,8)
Dim. F
.165 (4,2)
.172 (4,4)
Dim. G
.156 (4,0)
.187 (4,7)
AEP P/N
8955-1561-010
8955-1561-009
www.aepconnectors.com • aepsales@aepconnectors.com
3
MCX Miniature Coaxial Connectors
Straight P.C. Board Jacks • Through-hole legs with standoff
.200 (5,1) typ.
.235 (5,9) sq.
.200 (5,1) typ.
A
.245
(6,2)
.100 (2,5) typ.
.060 (1,5)
sq. typ.
ø.046 (1,2)
ø.177
(4,5)
ø.038
ø.067(1,7)
.035 (0,9)
sq. typ.
(1,0)
4 places
Mounting hole drilling
LEG LENGTH (A) BODY PLATING
.155
GOLD
.068
GOLD
.068
NICKEL
AEP P/N
8959-1511-000
8959-1511-002
8959-7511-002
Straight P.C. Board Jack • Surface mount
.235 (5,9) sq.
.245(6,2)
.200 (5,1)
typ.
.060 (1,5)
sq. typ.
.030
(0,8)
.080 (2,0)
sq. typ.
ø.177
(4,5)
ø.038
ø.068
(1,0)
(1,68)
Solder pads for mounting
AEP P/N
8959-1511-003
Right Angle P.C. Board Jack • Through-hole legs with standoff
.304 (7,7)
.192 (4,9)
.068
(1,7)
.235 (5,9) sq.
.200 (5,1)
typ.
.200 (5,1) typ.
.060 (1,5)
sq. typ.
.100 (2,5) typ.
ø.046 (1,2)
ø.038
.371
(9,4)
.035 (0,9)
sq. typ.
(1,0)
.254
(6,5)
.136
(3,5)
.01 (2,5)
ø.067(1,7)
4 places
Mounting hole drilling
ø.177
(4,5)
BODY PLATING
GOLD
NICKEL
APPLIED ENGINEERING PRODUCTS
(203) 776-2813 • FAX (203) 776-8294
AEP P/N
8960-1511-001
8960-7511-001
www.aepconnectors.com • aepsales@aepconnectors.com
4
MCX Miniature Coaxial Connectors
Assembly Instructions
Right Angle Connectors—Flexible Cable
Center conductor Dielectric
.060 ±.010
(1,5 ±0,2)
Cable stripping
Braid
Jacket
Right Angle Connectors—Semi-Rigid Cable
Center conductor
Cable stripping
Jacket
Dielectric
.094
(2,4)
.126 (3,2)
.125 ±.010
(3,2 ±0,2)
.265 ±.010
(6,7 ±0,2)
1
1
Solder
—Trim cable as shown; tin end of center conductor.
—Slide crimp sleeve over cable.
—Flare cable braid by rotating dielectric and slide cable into crimp tail.
—Trim cable as shown; tin end of center conductor.
—Insert trimmed cable into body until jacket bottoms on step inside
body and center conductor is in contact slot.
—Solder cable jacket to body assembly.
Solder
2
2
—Solder center conductor into notch in rear of contact with
.025–.032" diameter chisel-tip soldering iron.
—Solder should cover center conductor, but not extend over top of notch
in contact, or exceed contact diameter.
—Position cable so braid touches rear of body assembly.
—Slide crimp sleeve forward to touch rear of body assembly.
—Crimp braid with appropriate die size from chart below.
3
Solder
3
—Place insulator in body cavity, and press cap into place with .125"
diameter flat punch. Cap will be slightly below end of body assembly.
—Solder center conductor into notch in rear of contact with
.025–.032" diameter chisel-tip soldering iron.
—Solder should cover center conductor, but not extend over top of
notch in contact, or exceed contact diameter.
Assembly Tools
4
TA-0105
—Place insulator in body cavity, and press cap into place with .125"
diameter flat punch. Cap will be slightly below end of body assembly.
DESCRIPTION
Crimp tool with .105" and .128" hex dies
DESCRIPTION
CABLE GROUP
(last two digits of part number)
02
03
HEX DIE SIZE
.105
.128
APPLIED ENGINEERING PRODUCTS
(203) 776-2813 • FAX (203) 776-8294
Capping tool
(arbor press)
with bases for
MCX right angle
plugs.
AEP P/N
TA-0105
AEP P/N
CP-18
www.aepconnectors.com • aepsales@aepconnectors.com
CP-18
5
About AEP
Since our foundation in 1973, we have always
believed that having our customers take a look
“inside AEP” is important in fostering strong
vendor/customer relationships. We are proud of
our physical plant and equipment, but even more
so of our dedicated staff. When customers see
first-hand how AEP’s people keep a constant focus
on maintaining and improving customer service
and satisfaction, the reason for our consistently
strong on-time delivery and quality records
becomes clear.
We invite you to see for yourself. Call us to
arrange a plant tour—or, if you can’t make a visit,
ask for your copy of INSIDE AEP, our facilities and
capabilities brochure.
Other AEP Products
The MIL-PRF-39012 QPL connectors in this brochure are only part
of our complete line of coaxial connectors and cable assemblies, including:
• SMA
• SMB
• SMC
• SSMB
• SSMC
• SLB (Slide-on version of SMB)
• SLB/SA Self-aligning P.C. board receptacles
• SSLB (Slide-on version of SSMB)
• 75 ohm Miniature SMB
• 75 ohm Snap-on mating
• 75 ohm Screw-on mating
• MMCX edge mount
• Adapters within and between series
• Semi-rigid cable assemblies
Call for a copy of our 184-page full catalog to see them all.
APPLIED ENGINEERING PRODUCTS
104 John W. Murphy Drive • P.O. Box 510 • New Haven, CT 06513
(203) 776-2813 • FAX (203) 776-8294
www.aepconnectors.com • aepsales@aepconnectors.com
ISO 9001 CERTIFIED
MCX 1.0 9/01 • AEP P/N 127-4 Rev.—
• Flexible cable assemblies
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising