cx36b compact excavator tier 4 interim certified

cx36b compact excavator tier 4 interim certified
CX36B
ENGINE
Model
Yanmar 3TNV88-BPYB
Tier 4 Interim Certified
Cylinders
3.46 x 3.54 in
(88 x 90 mm)
Displacement
100 in3 (1.6 L)
Fuel injection pump
Fuel Fuel filter
Cooling
Direct
Mechanical
Diesel
Full flow
Liquid
Net horsepower @ 2400 RPM—SAE J1349:
28.4 hp (21.2 kW)
Net maximum torque @ 1440 RPM:
72.6 lb·ft (98.4 N·m)
POWERTRAIN
Travel speeds:
Low
High
Gradeability
Drawbar pull
Forward / Reverse
1.6 mph (2.6 kph)
2.8 mph (4.5 kph)
58% (30°)
8,655 lb (38 kN)
ELECTRICAL
Voltage
Alternator rating
Battery
OPERATING WEIGHT
SERVICE CAPACITY
Operating weight
7,958 lb (3610 kg)
w/ operator / full fuel / standard equipment
Fuel tank
3
Bore/Stroke
Fuel injection
COMPACT EXCAVATOR
TIER 4 INTERIM CERTIFIED
12 Volts
24 amp
12-volt low-maintenance
OPERATOR ENVIRONMENT
ROPS/FOPS three post canopy; Pilot operated
hand controls and foot pedals; Adjustable seat
w/ seat belt; Arm rests.
Display includes:
Engine oil pressure; Water temperature lamp; Air filter lamp; Water separator
detection lamp; Low fuel warning lamp;
Battery charge lamp; Glow plug indicator
lamp; Water temperature gauge; Fuel
gauge and hourmeter.
HYDRAULICS
Main pumps
Tandem variable displacement/ axial piston pump
Max. rated flow
Auxiliary flow
System relief pressure:
Standard
2 x 10.1 gpm
(2 x 38.4 L / min)
10 gal (38 L)
12.7 gal (48 L)
Engine w/ filter change
1.8 gal (6.7 L)
Radiator
1.2 gal (4.6 L)
OTHER SPECIFICATIONS
15.5 gpm (59.0 L / min)
Swing speed
0 – 8.9 RPM
3,336 psi (230 bar)
Swing brake
Spring applied,
hydraulically released
w/ dual cushion relief
Pilot control hydraulic system:
Pump
Gear pump
Maximum capacity
3.2 gpm (12.2 L / min)
Relief pressure
514 psi (35.4 bar)
10 spool
Control valves
Pilot control for left/right track travel, boom, arm, bucket and swing.
Manual control for breaker and backfill blade.
Swing / Dozer blade:
Motor
10 gal (38 L)
Hydraulic tank:
Refill capacity
Total system Fixed displacement
axial piston
Travel:
Motors – 2
Two-speed
axial piston
Final drive
Planetary gear
reduction
Boom cylinder Bore diameter
Rod diameter
Stroke
One (1)
3.15 in (80 mm)
1.97 in (50 mm)
22.7 in (578 mm)
Arm cylinders Bore diameter
Rod diameter
Stroke
Two (2)
3.15 in (80 mm)
1.77 in (45 mm)
22.05 in (560 mm)
Bucket cylinder Bore diameter
Rod diameter
Stroke
One (1)
2.56 in (65 mm)
1.38 in (35 mm)
19.6 in (497 mm)
Page 1 of 5
Undercarriage:
Top tracks – each
Bottom tracks – each
Boom:
Swing
Length
Boom w/ arm cylinder and plumbing
Arm:
Length
Bare arm
Bucket cylinder linkage
and plumbing
Total weight
1 roller
4 rollers
70° left/60° right
8 ft 2 in (2.49 m)
485 lb (220 kg)
4 ft 4 in (1.32 m)
165 lb (75 kg)
111 lb (50.3 kg)
276 lb (125.3 kg)
LIFT CAPACITIES
Canopy model — 4 ft 4 in (1.32 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down.
Load
(Lift Point)
Height
5 ft
(1.5 m)
END
7.5 ft
(2.3 m)
SIDE
END
10 ft
(3.0 m)
SIDE
END
12.5 ft
(3.8 m)
SIDE
+10 ft
(3.0 m)
+7.5 ft
(2.3 m)
15 ft
(4.6 m)
END
SIDE
1,190 lb
(540 kg)
1,120 lb
(510 kg)
1,380 lb
(620 kg)
1,380 lb
(620 kg)
1,280 lb
(580 kg)
1,100 lb
(500 kg)
+5 ft
(1.52 m)
2,760 lb
(1250 kg)
2,380 lb
(1080 kg)
1,830 lb
(830 kg)
1,510 lb
(680 kg)
1,480 lb
(670 kg)
1,050 lb
(470 kg)
+2.5 ft
(0.8 m)
3,760 lb
(1700 kg)
2,180 lb
(990 kg)
2,270 lb
(1030 kg)
1,420 lb
(640 kg)
1,690 lb
(760 kg)
1,000 lb
(450 kg)
Ground
Level
2,550 lb
(1150 kg)
2,550 lb
(1150 kg)
4,020 lb
(1820 kg)
2,120 lb
(960 kg)
2,520 lb
(1140 kg)
1,360 lb
(610 kg)
1,820 lb
(820 kg)
970 lb
(440 kg)
-2.5 ft
(-0.8 m)
4,080 lb
(1850 kg)
4,080 lb
(1850 kg)
3,830 lb
(1740 kg)
2,120 lb
(960 kg)
2,520 lb
(1140 kg)
1,340 lb
(610 kg)
1,800 lb
(810 kg)
960 lb
(430 kg)
-5 ft
(-1.52 m)
5,790 lb
(2620 kg)
4,550 lb
(2060 kg)
3,290 lb
(1490 kg)
2,150 lb
(970 kg)
2,210 lb
(1000 kg)
1,360 lb
(620 kg)
-7.5 ft
(-2.3 m)
3,470 lb
(1570 kg)
3,470 lb
(1570 kg)
2,110 lb
(950 kg)
2,110 lb
(950 kg)
END
SIDE
1,390 lb
(630 kg)
750 lb
(340 kg)
*Rated loads are hydraulic limits rather than tipping load limits.
Cab model — 4 ft 4 in (1.32 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down.
Load
(Lift Point)
Height
5 ft
(1.5 m)
END
7.5 ft
(2.3 m)
SIDE
END
10 ft
(3.0 m)
SIDE
END
12.5 ft
(3.8 m)
SIDE
15 ft
(4.6 m)
END
SIDE
+10 ft
(3.0 m)
1,190 lb
(540 kg)
1,190 lb
(540 kg)
+7.5 ft
(2.3 m)
1,280 lb
(580 kg)
1,160 lb
(530 kg)
+5 ft
(1.52 m)
2,760 lb
(1250 kg)
2,510 lb
(1140 kg)
1,830 lb
(830 kg)
1,600 lb
(720 kg)
1,480 lb
(670 kg)
1,120 lb
(500 kg)
+2.5 ft
(0.8 m)
3,760 lb
(1700 kg)
2,310 lb
(1050 kg)
2,270 lb
(1030 kg)
1,500 lb
(680 kg)
1,690 lb
(760 kg)
1,070 lb
(480 kg)
Ground
Level
2,550 lb
(1150 kg)
2,550 lb
(1150 kg)
4,020 lb
(1820 kg)
2,250 lb
(1020 kg)
2,520 lb
(1140 kg)
1,450 lb
(660 kg)
1,820 lb
(820 kg)
1,040 lb
(470 kg)
-2.5 ft
(-0.8 m)
4,080 lb
(1850 kg)
4,080 lb
(1850 kg)
3,830 lb
(1740 kg)
2,250 lb
(1020 kg)
2,520 lb
(1140 kg)
1,430 lb
(650 kg)
1,800 lb
(810 kg)
1,030 lb
(460 kg)
-5 ft
(-1.52 m)
5,790 lb
(2620 kg)
4,800 lb
(2180 kg)
3,290 lb
(1490 kg)
2,280 lb
(1030 kg)
2,210 lb
(1000 kg)
1,450 lb
(660 kg)
-7.5 ft
(-2.3 m)
3,470 lb
(1570 kg)
3,470 lb
(1570 kg)
2,110 lb
(950 kg)
2,110 lb
(950 kg)
END
SIDE
1,390 lb
(630 kg)
800 lb
(360 kg)
*Rated loads are hydraulic limits rather than tipping load limits.
Canopy model — 5 ft 3 in (1.59 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down.
Load
(Lift Point)
Height
5 ft
(1.5 m)
END
7.5 ft
(2.3 m)
SIDE
END
10 ft
(3.0 m)
SIDE
END
12.5 ft
(3.8 m)
SIDE
+10 ft
(3.0 m)
+7.5 ft
(2.3 m)
15 ft
(4.6 m)
END
SIDE
1,110 lb*
(450 kg)*
1,010 lb*
(450 kg)*
END
SIDE
1,140 lb*
(510 kg)*
1,140 lb*
(510 kg)*
1,120 lb*
(510 kg)*
1,100 lb
(500 kg)
1,120 lb*
(510 kg)*
780 lb
(350 kg)
+5 ft
(1.52 m)
2,260 lb*
(1020 kg)*
2,260 lb*
(1020 kg)*
1,600 lb*
(720 kg)*
1,520 lb*
(690 kg)*
1,340 lb*
(600 kg)*
1,050 lb
(470 kg)
1,210 lb*
(540 kg)*
760 lb
(340 kg)
+2.5 ft
(0.8 m)
3,430 lb*
(1550 kg)*
2,210 lb
(1000 kg)
2,090 lb*
(950 kg)*
1,420 lb
(640 kg)
1,570 lb*
(710 kg)*
1,000 lb
(450 kg)
1,310 lb*
(590 kg)*
730 lb
(330 kg)
1,380 lb*
(630 kg)*
710 lb
(320 kg)
Ground
Level
2,310 lb*
(1040 kg)*
2,310 lb*
(1040 kg)*
3,930 lb*
(1780 kg)*
2,100 lb
(950 kg)
2,420 lb*
(1100 kg)*
1,350 lb
(610 kg)
1,750 lb*
(790 kg)*
950 lb
(430 kg)
-2.5 ft
(-0.8 m)
3,540 lb*
(1600 kg)*
3,540 lb*
(1600 kg)*
3,910 lb*
(1770 kg)*
2,080 lb
(940 kg)
2,510 lb*
(1140 kg)*
1,320 lb
(590 kg)
1,800 lb*
(810 kg)*
930 lb
(420 kg)
-5 ft
(-1.52 m)
4,990 lb*
(2260 kg)*
4,440 lb
(2010 kg)
3,520 lb*
(1590 kg)*
2,100 lb
(950 kg)
2,330 lb*
(1050 kg)*
1,320 lb
(600 kg)
1,620 lb
(730 kg)
940 lb
(430 kg)
-7.5 ft
(-2.3 m)
4,610 lb*
(2090 kg)*
4,580 lb
(2070 kg)
2,620 lb*
(1180 kg)*
2,170 lb
(980 kg)
*Rated loads are hydraulic limits rather than tipping load limits.
CX36B • Page 2 of 5
B
C
K
A
H
L
J
F
G
D
E
Line drawings are for illustrative purpose only and may not be exact representation of unit.
DIMENSIONS
A.
Overall height 8 ft 5 in (2.57 m)
B. Overall length 15 ft 5 in (4.71 m)
C. Width of upperstructure 5 ft 1 in (1.55 m)
D. Track overall length 7 ft 1 in (2.15 m)
E.
Track overall width with 11.8 in (300 mm) shoes 5 ft 7 in (1.70 m)
F.
Track shoe width 11.8 in (300 mm)
G. Center to center – idler to sprocket 5 ft 7 in (1.70 m)
H. Upperstructure ground clearance J.
1 ft 10 in (570 mm)
Minimum ground clearance 12.9 in (330 mm)
K. Tail swing radius L.
2 ft 9 in (850 mm)
Backfill blade height
1 ft 1 in (345 mm)
Working weight 7,958 lb (3610 kg)
Ground pressure 4.6 psi (32 kPa)
Boom swing
Left 70°/Right 60°
Tail swing overhang 0 ft 0 in (0 m)
CX36B • Page 3 of 5
M
N
S
R
Q
T
P
Line drawings are for illustrative purpose only and may not be exact representation of unit.
PERFORMANCE SPECS
5 ft 3 in (1.59 m) Arm
4 ft 4 in (1.32 m) Arm
M. Maximum dig radius
18 ft 0 in (5.50 m)
17 ft 2 in (5.24 m)
N. Dig radius at groundline 17 ft 7 in (5.37 m)
16 ft 8 in (5.11 m)
P.
11 ft 0 in (3.35 m)
10 ft 1 in (3.07 m)
12 ft 4 in (3.76 m)
11 ft 8 in (3.58 m)
16 ft 11 in (5.16 m)
16 ft 3 in (4.98 m)
Maximum dig depth
Q. Dump height R. Overall reach height S.
Bucket rotation T.
Vertical straight wall dig depth 178°
178°
8 ft 8 in (2.65 m)
7 ft 10 in (2.39 m)
Arm digging force 3,731 lb (17 kN)
4,203 lb (19 kN)
Bucket digging force:
2 position bucket
8,430 lb (37 kN)
8,430 lb (37 kN)
CX36B • Page 4 of 5
STANDARD EQUIPMENT
OPERATOR ENVIRONMENT
HYDRAULICS
UPPER STRUCTURE
See page 1
Zero tail swing
ENGINE
Auxiliary hydraulics – single / bi-directional –
and plumbing to arm
Yanmar 3TNV88-BPYB diesel
Large hydraulic oil cooler
Swing brake
4 Cycle
Control pattern selector valve
Swing shock valve
Water cooled
TRACK DRIVE
OTHER
Direct injection
Rubber tracks
Swing boom – 70° left / 60° right
One touch decelerator
Automatic 2-speed travel
Hydraulic backfill blade
Engine access under rear hood
Fully hydrostatic drive system
Dry type air cleaner with restriction indicator
Sealed and lubricated track rollers
Glow plug starting aid
Track tension adjustment – grease type
ELECTRICAL
Disc type parking brake – auto release and apply
Swing lock
12-volt electrical starting system
Heavy-duty battery
Horn
OPTIONAL EQUIPMENT
OPERATOR ENVIRONMENT
OTHER
Cab enclosure with heater
Steel tracks
5 ft 3 in (1.59 m) arm
Mechanical coupler
Rigid thumb
Rigid thumb-coupler
BUCKETS
Width
SAE Heaped Capacity
Weight
12 in (305 mm)
2.13 ft3 (0.060 m3)
155 lb (70 kg)
24 in (610 mm)
4.25 ft3 (0.120 m3)
218 lb (99 kg)
36 in (914 mm)
6.60 ft3 (0.186 m3)
290 lb (132 kg)
NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices,
where applicable.
NOTE: All engines meet current EPA emissions requirements.
IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications
without notice and without incurring any obligation relating to such change. Case Construction
Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers.
Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those
respective companies.
www.casece.com
Form No. CCE201212CX36B
Replaces form no. CCE5010801
Printed in U.S.A.
CX36B • Page 5 of 5
All Case construction equipment is biodiesel ready.
© 2012 CNH America LLC
All Rights Reserved
CX B SERIES
COMPACT EXCAVATORS
CX17B | CX27B | CX31B | CX36B | CX55B
MINI EXCAVATORS. MANY ADVANTAGES.
Whether you’re a small business or a general contractor needing impressive power within a small
space, the full line of CASE compact excavators offer all the features and functionality needed
to handle the toughest jobs in the tightest places. Four Tier 4 Interim models and the Tier 4 Final
CX55B deliver breakout forces from 3,417 to 11,028 lbs. and digging depths up to nearly 13 feet.
And it’s all powered by high-efficiency hydraulics that maximize performance, and precision
controls that instantly feel familiar. Experience the big-time benefits of the CX B Series.
Zero Tail Swing*
*Excludes CX55B
Center-Swing
Boom Control
Integrated-Flow
Pump System
Exclusive In-Frame
Sliding Door*
*Excludes CX55B
2
Models Available
CX17B
CX27B
CX31B
CX36B
Three-Post
ROPS Design
CX55B
Automatic*
Two-Speed Travel
*Manual two-speed travel on
CX17B and CX27B
3
IT HOLDS NOTHING BACK.
IN THE CLEAR WITH ZERO TAIL SWING*
CASE compact excavators offer a true, zero-radius tail swing that
keeps the sides and back of the machine within the width of the
tracks when rotating – even with the door open. You can dig and
dump 180°, right against obstacles, without a problem and with less
risk of damaging the machine or worksite.
*Excludes CX55B
FOOT PEDAL CENTER-SWING BOOM CONTROL
A foot-controlled boom swing allows for simultaneous operation
of the house and boom. Coupled with a center-swing design that
angles the boom up to 80° left and 65° right, operators are able to
dig and use attachments around trees and parallel with foundations,
fences, walls or whatever’s on the worksite.
INTEGRATED-FLOW PUMP SYSTEM:
SMART POWER PLACEMENT
This innovative system helps improve fuel efficiency and maximize
strength by directing hydraulic power to where you need it, when you
need it. With dozing, flow is focused on the tracks and blade. When
swinging or raising the arm, pump power is diverted to the boom.
During digging, all flow is pumped to the bucket and arm.
FASTER CYCLE TIMES WITH TWO-SPEED TRAVEL
Automatic on the CX31B, CX36B and CX55B, and push-button
activated on the CX17B and CX27B, the two-speed travel drive
function matches speed and performance to jobsite conditions. All
models also include one-touch engine deceleration to quickly cut
engine RPMs for greater fuel savings and reduced noise levels.
RETRACTABLE TRACKS
Getting through backyard gates or any tight spot is easy for the CX17B, thanks to tracks that
hydraulically retract from 52 inches to a narrow 39-inch width. And all our compact excavators come
standard with durable rubber tracks with big, deep nubs for greater grip. CASE even offers steel
tracks on every model for heavy-duty applications.
4
“My two CASE compact excavators
just shine. We have had zero problems.”
— Benoit Drainage
5
3-POST CANOPY*.
360° VISIBILITY.
Our ROPS-certified three-post
canopy design creates a wideopen entry area for easier
access in and out
of the operating
platform. And
as an added
benefit, the
absence of
a fourth post
provides greater
visibility of the
attachment and
around the
machine.
*CX55B features a
four-post ROPS/
FOPS-certified
canopy.
6
GET A LITTLE MORE COMFORTABLE.
SMARTEST CAB DOOR IN ITS CLASS
What’s the point of a zero tail swing design if the open door hangs
over the tracks? CASE compact excavators* come standard with
a cab door that slides all the way open within the machine frame,
keeping it securely out of the way.
*Excludes CX55B
Exclusive sliding cab door
maintains zero tail swing.
PRECISION CONTROLS COME STANDARD
All CASE compact excavators – even our smallest models – come
standard with hydraulic pilot controls for comfortable, highly
responsive operation. On top of that, all models also feature a
pattern control selector valve that lets you easily toggle between
ISO and SAE patterns to meet operator preference.
Proportional auxiliary hydraulics
joystick with thumb toggle puts
precision at your fingertips.
CONSTRUCTED FOR COMFORT
With an adjustable seat and standard arm rest, as well as an
optional heating and A/C system* for our enclosed cabs, the
spacious operating platforms of the CX B Series help keep you
comfortable all day long and all year ‘round.
*HVAC system only available on the CX31B and larger.
Spacious CX55B cab offers an optional
LCD display.
7
COMPACT CLASS,
MID-SIZE MUSCLE.
CX55B
The CX55B pushes the envelope of
what it means to be a mini-excavator. It
features best-in-class power, a wider
operating range and a cab design that
offers plenty of room and superior
visibility – all while maintaining
minimum tail swing and an
overall cab height of only 8-feet
4-inches. It’s perfect for when
you need a lot of strength in a
little package.
8
7.5-INCH MINIMAL TAIL SWING
Minimal tail overhang allows for excellent
maneuverability in tight areas.
ECO MODE
Achieve 25% less fuel consumption at the push
of a button (compared to previous generation).
iNDr COOLING SYSTEM
A revolutionary Integrated Noise and Dust
Reduction (iNDr) filter removes dust before
cooling components to maximize cooling
efficiency and reduce cleaning intervals. It also
delivers amazingly quiet operation.
DOZER-STYLE BLADE
A new, “one-pass” backfill blade design forms
material into an arc that always falls forward.
LCD MONITOR
An optional LCD monitor makes performance
data and machine diagnostics readily available.
9
MAINTENANCE MADE EASY.
SERVICEABILITY IS IN OUR DNA
When you invest in CASE equipment, you need it to last. We make it simple. CASE
compact excavators are no exception. From wide-open, swing-out access panels
to ground-level site gauges and service points, you can do daily maintenance in a
matter of minutes. It’s the easiest way to help you get the most performance and
longest life out of your machine.
Update Livery
EASY ACCESS TO EVERYTHING
10
1.Air filter
2.Water separator
3.Fuel filter
4.Hydraulic oil fill
5.Radiator
6.Grouped hydraulic hoses
7. Hydraulic site gauge
8.Hour meter
9.ISO/SAE pattern changer
10.Single/bi-directional select
11.Lockable fuel cap
12.Engine oil fill
13.Engine oil filter
14.Fuel drain
15.Coolant reservoir
SUPPORT COMES STANDARD
Base & Extended Warranty Coverage*
1-Year/1,000-Hour Full-Coverage
Limited Base Warranty.
*Please see your CASE dealer for limitations, exclusions
and confirmation of policies in effect.
Purchased Protection Plan
Extension of the factory base and extended
coverage is available at an additional cost.
Plans are available up to three years/3,000
hours on CASE compact excavators. Talk to
your CASE dealer to determine the plan that
best fits your needs. Breakdown Assistance
Standard on all CASE equipment.
STRONGER PRODUCT SUPPORT
SOLUTIONS
NO TOOLS NEEDED
The CX B Series continues the CASE hallmark of simple serviceability
with features like tool-free access to routine maintenance points.
Your CASE dealer knows best how you can
maximize your equipment investment and
uptime, with genuine CASE parts, expert
service and a complete range of product
support solutions – including CASE
remanufactured and all-makes parts. CASE
supports better parts availability and faster
deliveries, through nine parts distribution
centers in North America and a forecasting
system to ensure that the right parts will be
there when you need them. And only CASE
dealers have exclusive access to the Electronic
Service Tool that quickly pinpoints machine
issues to help maximize uptime.
11
AUXILIARY EXCELLENCE
Auxiliary hydraulics come standard
with lines plumbed all the way down
the arm for easy hook-up.
12
ATTACHMENTS GALORE.
BUCKETS AND MUCH MORE
There’s a full range of attachments, including a full
line of CASE buckets with a wide range of sizes
and digging forces.
INDUSTRY-EXCLUSIVE BLADE DESIGN
CASE dozer blades feature an increased 38°
approach angle and a unique shape that efficiently
rolls dirt as it pushes, leaving a smooth and level
surface. And with the optional 4-way blade*,
operators can raise and lower the blade for added
stability and improved backfilling or grading.
*4-way angle blade available on the CX31B and larger
SMARTFIT™ BUCKET TEETH
CASE compact excavator buckets come
standard with the innovative SmartFit bucket
tooth system. These heavy-duty, self-sharpening
teeth combine exceptional strength and
unmatched ease of installation, thanks to a
hammerless fastener system with reusable
locking pins. Available in a full range of styles.
13
THE CX B SERIES
COMPACT EXCAVATORS
CX17B
CX27B
CX31B
CX36B
CX55B Tier 4 Final
Mitsubishi
L3E-W231KBS
Yanmar
3TNV82-A-SYB
Yanmar
3TNV88-BPYB
Yanmar
3TNV88-BPYB
Yanmar
4TNV88-C-PYB
Net hp (kW)
15.2 (11.3)
@ 2200 RPM
21.3 (15.9)
@ 2200 RPM
28.4 (21.2)
@ 2400 RPM
28.4 (21.2)
@ 2400 RPM
39.3 (29.3)
@ 2400 RPM
Emissions certification*
Tier 4 Interim
Tier 4 Interim
Tier 4 Interim
Tier 4 Interim
Tier 4 Final
(CEGR/DPF)
Bucket digging force – lb. (kN)
3,417
(15.2)
6,351
(28.2)
8,430
(37.5)
8,430
(37.5)
11,128
(49.5)
Arm digging force – lb. (kN)
1,956
(8.7)
2,877
(12.8)
3,373
(15.0)
3,731
(17.0)
5,300
(23.7)
Operating weight – lb. (kg)
3,638
(1 650)
5,556
(2 520)
6,679
(3 030)
7,958
(3 610)
11,310
(5 130)
Overall height
7 ft. 9 in.
(2.35 m)
8 ft. 2 in.
(2.50 m)
8 ft. 5 in.
(2.57 m)
8 ft. 5 in.
(2.57 m)
8 ft. 4 in.
(2.55 m)
Overall length
11 ft. 3 in.
(3.42 m)
13 ft. 11 in.
(4.13 m)
14 ft. 4 in.
(4.39 m)
15 ft. 5 in.
(4.71 m)
17 ft. 10 in.
(5.42 m)
Width of upperstructure
2 ft. 11 in.
(0.89 m)
4 ft. 7 in.
(1.40 m)
5 ft. 1 in.
(1.55 m)
5 ft. 1 in.
(1.55 m)
6 ft. 4 in.
(1.94 m)
Track overall length
5 ft. 2 in.
(1.56 m)
6 ft. 6 in.
(1.98 m)
6 ft. 7 in.
(2.00 m)
7 ft. 1 in.
(2.15 m)
8 ft. 1 in.
(2.48 m)
Track overall width with shoes**
4 ft. 4 in.
(1.32 m)
4 ft. 11 in.
(1.50 m)
5 ft. 1 in.
(1.55 m)
5 ft. 7 in.
(1.70 m)
6 ft. 6 in.
(1.98 m)
Track shoe width
9.1 in.
(230 mm)
9.8 in.
(250 mm)
11.8 in.
(300 mm)
11.8 in.
(300 mm)
15.7 in.
(400 mm)
Upperstructure ground clearance
18.0 in.
(445 mm)
20.0 in.
(520 mm)
22.0 in.
(570 mm)
22.0 in.
(570 mm)
24.5 in.
(625 mm)
Minimum ground clearance
6.9 in.
(175 mm)
9.8 in.
(250 mm)
12.9 in.
(330 mm)
12.9 in.
(330 mm)
14.0 in.
(350 mm)
Rear tail swing radius
2 ft. 2 in.
(0.66 m)
2 ft. 5 in.
(0.75 m)
2 ft. 7 in.
(0.79 m)
2 ft. 9 in.
(0.85 m)
4 ft. 2 in.
(1.28 m)
7 ft. 1 in.
(2 159 mm)
8 ft. 4 in.
(2 540 mm)
9 ft. 2 in.
(2 794 mm)
10 ft. 1 in.
(3 073 m)
12 ft. 10 in.
(3 912 mm)
SPECIFICATIONS
Engine
DIMENSIONS
Digging depth
NOTE: *CEGR = Cooled Exhaust Gas Recirculation; DPF = Diesel Particulate Filter.
**Measurements taken using standard equipment.
14
BUILDING A STRONG CASE
Already in high gear with the arrival of founder J.I.
Case’s portable steam engine in 1869, we found
ourselves at the heart of the road construction
boom of the early 1900s. The path was set.
Today, CASE is a game changer in construction
equipment, financing, parts and service.
Revolutionary is nothing new to CASE, as
innovations like the integrated loader/backhoe
(1957), Ride Control™, over-center boom design
and ProCare have shown. It’s this ingenuity and
spirit that fuels our ongoing pursuit of building
industry-leading performance and productivity
into every machine throughout our full line of light,
medium and heavy equipment.
All of this is backed by a portfolio of more than
10,000 OEM, REMAN and Gold Value parts, more
than 350 North American dealer locations, and
unmatched financial and insurance services that
ensure the best support is always within reach.
When all is said and done, our strength is only as
solid as the machines we engineer, the support
and service we give, and most importantly, the
vote of confidence CASE customers have with
every bit of it.
Specialized finance programs and flexible leasing
packages put you in the driver’s seat of industryleading CASE equipment, while no-nonsense
warranties and comprehensive protection plans
ensure that your equipment is protected. As the
only finance company dedicated to CASE, we offer
strong products and services designed around
your unique needs and are the only ones supported
by the helpful service professionals at your CASE
dealer.
To learn more about CASE or for attentive
customer service, visit your nearest dealer, call
1-866-54CASE6 or visit us online at CaseCE.com.
15
CaseCE.com
©2014 CNH Industrial America LLC. All rights reserved. CASE is a
trademark registered in the United States and many other countries,
owned by or licensed to CNH Industrial N.V., its subsidiaries or
affiliates. CNH Industrial Capital is a trademark in the United States and
many other countries, owned by or licensed to CNH Industrial N.V., its
subsidiaries or affiliates. Printed in U.S.A.
Form No. CCE201401CEXC
Always read the Operator’s Manual
before operating any equipment. Inspect
equipment before using it, and be sure it
is operating properly. Follow the product safety signs and use any safety
features provided.
NOTE: All engines meet current EPA emission regulations.
NOTE: All specifications are stated in accordance with SAE Standards
or Recommended Practices, where applicable.
Contains 10%
post-consumer fiber
IMPORTANT: CASE Construction Equipment Inc. reserves the right
to change these specifications without notice and without incurring
any obligation relating to such change. Availability of some models
and equipment builds vary according to the country in which the
equipment is used. The illustrations and text may include optional
equipment and accessories and may not include all standard equipment. Your CASE dealer/distributor will be able to give you details of
the products and their specifications available in your area.
CASE Construction Equipment
is biodiesel friendly.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising