User Manual - Projector Central

User Manual - Projector Central
LCD Projector
8961WU/8963
8962WU/8960W
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
WARNING ►Before using this product, please read all manuals for this
product. Be sure to read Safety Guide first. After reading them, store them in a
safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
described below.
WARNING This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
CAUTION This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect handling.
NOTICE
This entry notices of fear of causing trouble.
 Please refer to the pages written following this symbol.
NOTE • The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• VESA and DDC are trademarks of the Video Electronics Standard Association.
•H
DMITM, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
• DICOM® is the registered trademark of the National Electrical Manufacturers Association
for its standards publications relating to digital communications of medical information.
• HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
• MHL®, the MHL logo, and Mobile High-Definition Link are trademarks or registered
trademarks of MHL, LLC in the United States and other countries.
All other trademarks are the properties of their respective owners.
430-8960W-8961WU-8962WU-8963-General-00
1
Contents


Introduction . . . . . . . . . . . . . . . 3 AUDIO menu . . . . . . . . . . . . . . 75
Features . . . . . . . . . . . . . . . . . . . . . . . 3 SCREEN menu. . . . . . . . . . . . . 76
Checking the contents of package. . . . . 3
Part names . . . . . . . . . . . . . . . . . . . . . 4 OPTION menu. . . . . . . . . . . . . 82
Projector, Control panel, Ports,
NETWORK menu. . . . . . . . . . . 95
Remote control
SECURITY menu. . . . . . . . . . . 96
Setting up . . . . . . . . . . . . . . . . . 8
Arrangement. . . . . . . . . . . . . . . . . . . . 9 Maintenance. . . . . . . . . . . . . 103
Connecting with your devices. . . . . . 12 Replacing the lamp. . . . . . . . . . . . . 103
Fastening the cables. . . . . . . . . . . . . 22 Cleaning and replacing the air filter . 105
Fastening the adapter cover. . . . . . . 23 Replacing the internal clock battery. .107
Attaching the terminal cover. . . . . . . 24 Other care. . . . . . . . . . . . . . . . . . . . 108
Using the security bar and slot . . . . . 25 Troubleshooting . . . . . . . . . . 109
Connecting power supply . . . . . . . . . 26 Related messages. . . . . . . . . . . . . . . 109
Remote control. . . . . . . . . . . . 27 Regarding the indicator lamps . . . . 112
Installing the batteries. . . . . . . . . . . . 27 Resetting all settings. . . . . . . . . . . . 116
Changing the frequency of remote control signal. . . 28 Phenomena that may be easy to
About the remote control signal . . . . 29
be mistaken for machine defects. . . 117
Power on/off . . . . . . . . . . . . . . 30 Specifications. . . . . . . . . . . . 124
Turning on the power . . . . . . . . . . . . 30
Turning off the power . . . . . . . . . . . . 31
Operating . . . . . . . . . . . . . . . . 32
Adjusting the volume. . . . . . . . . . . . . 32
Temporarily muting the sound. . . . . . 32
Selecting an input signal. . . . . . . . . . 33
Selecting an aspect ratio. . . . . . . . . . 34
Adjusting the projector's elevator . . . . . 35
Adjusting the zoom and focus. . . . . . 35
Adjusting the lens shift . . . . . . . . . . . 36
Using the automatic adjustment feature. . . 37
Correcting the distortion . . . . . . . . . . 38
Using the EDGE BLENDING features. . . 41
Using the magnify feature. . . . . . . . . 45
Temporarily freezing the screen . . . . 46
Temporarily blanking the screen. . . . 46
PbyP (Picture by Picture) /
PinP (Picture in Picture). . . . 47
Using the menu function . . . . . . . . . . 51
Indication in OSD,
Containing items of each menu
EASY MENU. . .
PICTURE menu .
IMAGE menu. . .
INPUT menu . . .
SETUP menu. . .
2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 54
56
60
63
68
Introduction
Introduction
Features
The projector provides you with the broad use by the following features.
ü T
he HDMITM/MHL/HDBaseTTM ports can support various image equipment
which have digital interface to get clearer pictures on a screen.
ü The wealth of I/O ports is believed to support any business scene.
ü H
as an HDCR and an ACCENTUALIZER features which are Dukane's original
image stabilizer for a clearer image.
ü H
as a DICOM® (“Digital Imaging and Communication in Medicine”) simulation
mode. This mode simulates the DICOM standard, which is a standard
applicable to digital communications in medicine.
ü The built-in 16W speaker can deliver sufficient sound volume in a large space
like a classroom without external speakers.
ü E
quipped with IMAGE OPTIMIZER which is Dukane's original function to
maintain visibility by automatic image correction in accordance with lamp
deterioration.
Checking the contents of package
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Require
of your dealer immediately if any items are missing.
WARNING ►Keep small parts away from children and pets. Take care not
to put in the mouth. If swallowed, consult a physician immediately for emergency
treatment.
NOTE • Keep the original packing materials for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
Note: The Dukane models described in this document are manufactured by Hitachi and use
the same firmware, software programs, control code, and accessory parts. The equivalent
Dukane to Hitachi models are; 8960W (CP-WX5505), 8961WU (CP-WU5500), 8962WU
(CP-WU5505), and 8963 (CP-X5550).
3
Introduction
Part names
Projector
(1) Lamp cover (103)
The lamp unit is inside.
(2) Speaker (32, 75)
(3) Filter cover (105)
The air filter and intake vent
are inside.
(4) Elevator feet (x2) (35)
(5) Elevator buttons (x2)
(6) Remote sensor (29, 89)
(7) Lens cover
(8) Intake vents
(9) Control panel (5)
(10) AC (AC inlet) (26)
(11) Exhaust vents
(12) Ports (6)
(13) Security bar (25)
(14) Security slot (25)
(15) Battery cover (107)
8961WU/8962WU
(6)
(3)
(7)
(2)
8960W
8963
(6)
(5)
(4)
(3)
(7)
(2)
(5)
(4)
(9)
(1)
(14)
(12)
(10)
(8)
(13)
(11)
(5)
(4)
(15)
(continued on next page)
4
Introduction
Part names (continued)
WARNING ►Do not open or remove any portion of the product, unless the
manuals direct it.
►Do not subject the projector to unstable conditions.
►Do not apply a shock or pressure to this product. Remove all the attachments
including the power cord and cables, from the projector when carrying the
projector.
►Do not look into the lens and the openings on the projector while the lamp is on
since the projection ray may cause a trouble on your eyes.
►Keep any object away from concentrated projection light beam. Blocking the
beam by something causes high temperature and could result in fire or smoke.
CAUTION ►Do not touch around the lamp cover and the exhaust vents
during use or just after use, since it is too hot.
►Do not attach anything onto the lens except the lens cover of this
projector because it could damage the lens, such as melting the lens.
Control panel
(1) STANDBY/ON button (&30)
(2) INPUT button (&33, 51)
(3) MENU button (&51)
(4) SECURITY indicator (&102)
(5) LAMP indicator (&112 ~ 115)
(6) TEMP indicator (&112 ~ 115)
(7) POWER indicator (&30, 112 ~ 115)
(5) (4)
(1)
(2)
(3)
(6) (7)
(continued on next page)
5
Introduction
Part names (continued)
Ports (&12~21)
(1) COMPUTER IN port
(2) HDBaseT port *
(3) LAN port
(4) WIRELESS port
(5) HDMI 1 / MHL port
(6) HDMI 2 port
(7) HDMI OUT port
(8) VIDEO port
(9) AUDIO IN1 port
(10) AUDIO IN2 (L, R) ports
(11) AUDIO OUT port
(12) MONITOR OUT port
(13) REMOTE CONTROL IN port
(14) REMOTE CONTROL OUT port
(15) CONTROL port
* 8962WU/8960W only
8960W/8962WU
(7)
(5)
(6) (12) (4)
(3)
(2)
(1)
(11)
(10)
(8) (9) (15)
(13) (14)
8961WU/8963
(7)
(5)
(6) (12) (4)
(3)
(1)
(11)
(10)
6
(8) (9) (15)
(13) (14)
Introduction
Part names (continued)
Remote control
(1) INPUT button (&33)
(2) MY BUTTON-1 button (&84)
(3) MY BUTTON-2 button (&84)
(4) STANDBY/ON button (&30)
(5) ASPECT button (&34)
(6) PbyP button (&47)
(7) AUTO button (&37)
(8) FREEZE button (&46)
(9) MAGNIFY ON button (&45)
(10) FOCUS + button *
(11) ZOOM + button *
(12) VOLUME + button (&32)
(13) MAGNIFY OFF button (&45)
(14) FOCUS - button *
(15) ZOOM - button *
(16) VOLUME - button (&32)
(17) PAGE UP button
(18) GEOMETRY button (&38)
(19) PICTURE button
(20) MUTE button (&32)
(21) PAGE DOWN button
(22) INTERACTIVE button *
(23) NETWORK button
(24) BLANK button (&46)
(25) ESC button (&28)
(26) MENU button (&51)
(27) ENTER button (&51)
(28) OSD MSG button (&73)
(29) RESET button (&51)
(30) ▲/▼/◄/►cursor buttons (&51)
(31) Battery cover (&27)
(2)
(1)
(6)
(5)
(10)
(9)
(14)
(13)
(17)
(18)
(21)
(22)
(25)
(30)
(28)
MYBUTTON
INPUT
1
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
PAGE
UP
DOWN
+
GEOMETRY
2
+
PICTURE
INTERACTIVE NETWORK
ESC
+
-
MUTE
BLANK
MENU
ENTER
OSD MSG
RESET
(3)
(4)
(7)
(8)
(11)
(12)
(15)
(16)
(20)
(19)
(24)
(23)
(26)
(27)
(29)
(31)
Back of
the remote control
NOTE • Any button marked with “*” is not supported on this projector (&111).
• Some keys are unavailable when OSD MESSAGE is set to INHIBIT(&73).
7
Setting up
Setting up
Install the projector according to the
environment and manner the projector will be
used in.
For the case of installation in a special state
such as ceiling mount, the specified mounting
accessories and service may be required.
Before installing the projector, consult your
dealer about your installation.
Secure a clearance of 50cm or greater between the exhaust vents and walls, and
a clearance of 30cm or greater between the intake vents and walls. Assume that
there is enough clearance in the front, back, and top of the projector in the figure
below.
50cm or greater
Exhaust
vents
30cm or greater
Intake
vents
Secure a clearance of 30cm or greater between the intake vents and walls.
Assume that there is enough clearance in the front, sides, and top of the projector
in the figure below.
30cm or greater
Intake
vents
8
Setting up
Arrangement
Refer to tables T-1 to T-3 at the back of User’s Manual (concise) as well as the
following to determine the screen size and projection distance. The values shown
in the table are calculated for a full size screen.
Projector top
Projector bottom
Ⓗ × Ⓥ : Screen size
ⓐ : Projection distance (from the front of the projector unit)
(continued on next page)
9
Setting up
Arrangement (continued)
WARNING ►Install the projector where you can access the power
outlet easily. If an abnormality should occur, unplug the projector urgently.
Otherwise it could cause a fire or electric shock.
►Do not subject the projector to unstable conditions. If the projector falls
or topples over, it could result in injury or damage to the projector and the
surrounding things. Using a damaged projector could result in a fire and an
electric shock.
• Do not place the projector in unstable places, such as an inclined surface,
places subject to vibration, on top of a wobbly table or cart, or a surface that is
smaller than the projector.
• Do not put the projector on its side, front or rear position.
• Do not attach nor place anything on the projector unless otherwise specified in
the manual.
• Do not use any mounting accessories except the accessories specified by the
manufacturer. Read and keep the manuals of the accessories used.
• For special installation such as ceiling mounting, be sure to consult your dealer
beforehand.
• Remove all the attachments including the power cord and cables, from the
projector when carrying the projector.
►Do not install the projector near thermally conductive or flammable
things. Such things when heated by the projector could result in a fire and burns.
• Do not place the projector on a metal stand.
►Do not place the projector where any oils, such as cooking or machine
oil, are used. Oil may harm the product, resulting in malfunction, or falling from
the mounted position.
►Do not place the projector in a place where it may get wet. Getting the
projector wet or inserting liquid into the projector could cause a fire and an
electric shock, and damage the projector.
• Do not place the projector near water, such as in a bathroom, kitchen, or
poolside.
• Do not place the projector outdoors or by the window.
• Do not place anything containing liquid near the projector.
►Do not block the intake vents and exhaust vents of the projector. If the
intake vents and exhaust vents of the projector are blocked, the accumulated
inside heat may cause fire.
(continued on next page)
10
Setting up
Arrangement (continued)
CAUTION ►Place the projector in a cool place with sufficient
ventilation. The projector may shutdown automatically or may malfunction if its
internal temperature is too high.
Using a damaged projector could result in a fire and an electric shock.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
• Do not place the projector on carpet, cushions or bedding.
• Do not stop up, block nor cover the projector's vent holes. Do not place
anything around the projector that could be sucked in or stuck to the projector's
intake vents.
• Do not place the projector at places that are exposed to magnetic fields, doing
so can cause the cooling fans inside the projector to malfunction.
►Avoid placing the projector in smoky, humid or dusty place. Placing the
projector in such places could cause a fire, an electric shock and malfunction of
the projector.
• Do not place the projector near humidifiers. Especially for an ultrasonic
humidifier, chlorine and minerals contained in tap water are atomized and could
be deposited in the projector causing image degradation or other problems.
• Do not place the projector in a smoking area, kitchen, passageway or by the
window.
NOTICE • Position the projector to prevent light from directly hitting the
projector's remote sensor.
• Do not place the product in a place where radio interference may be caused.
• Set the ALTITUDE of the SERVICE item in the OPTION menu correctly. If the
projector is used at an altitude of about 1600 m or higher, set ALTITUDE of
the SERVICE item in the OPTION menu to HIGH (&88). Otherwise, set it to
NORMAL.
• Keep heat-sensitive things away from the projector. Otherwise, they may be
damaged by the heat from the projector.
NOTE • When the temperature inside the projector rises high, it may cause the
high rotation of the fan for cooling temporarily.
11
Setting up
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to
confirm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform
the connection, according to the following instructions. Refer to the figures in
subsequent pages.
Before connecting the projector to a network system, be sure to read Network
Guide too.
WARNING ►Use only the appropriate accessories. Otherwise it could
cause a fire or damage the projector and devices.
• Use only the accessories specified or recommended by the projector’s
manufacturer. It may be regulated under some standard.
• Neither disassemble nor modify the projector and the accessories.
• Do not use the damaged accessory. Be careful not to damage the accessories.
Route a cable so that it is neither stepped on nor pinched out.
CAUTION ►For a cable with a core at only one end, connect the end
with the core to the projector. That may be required by EMI regulations.
NOTE • Do not turn on or off the projector while connected to a device in
operation, unless that is directed in the manual of the device. Otherwise it may
cause malfunction in the device or projector.
• The function of some input ports can be selected according to your usage
requirements. Check the reference page indicated beside each port in the
following illustration.
• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it
may cause malfunction in the device or projector.
- When connecting a connector to a port, make sure that the shape of the
connector fits the port.
- Tighten the screws to connect a connector equipped with screws to a port.
- Use the cables with straight plugs, not L-shaped ones, as the input ports of
the projector are recessed.
About Plug-and-Play capability
• Plug-and-Play is a system composed of a computer, its operating system
and peripheral equipment (i.e. display devices). This projector is VESA DDC
2B compatible. Plug-and-Play can be used by connecting this projector to a
computer that is VESA DDC (display data channel) compatible.
- Take advantage of this feature by connecting a computer cable to the
COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
- Please use the standard drivers in your computer as this projector is a Plugand-Play monitor.
(continued on next page)
12
Setting up
Connecting with your devices (continued)
8962WU/8960W
Computer
HDBaseT
Smartphone
Tablet
8961WU/8963
Computer
Smartphone
Tablet
(continued on next page)
13
Setting up
Connecting with your devices (continued)
NOTE • Before connecting the projector to a computer, consult the computer’s
manual and check the compatibility of the signal level, the synchronization
methods and the display resolution output to the projector.
- Some signal may need an adapter to input this projector.
- Some computers have multiple screen display modes that may include some
signals which are not supported by this projector.
- Although the projector can display signals with a resolution up to UXGA
(1600x1200) or up to W-UXGA (1920x1200), the signal will be converted
to the projector’s panel resolution before being displayed. The best display
performance will be achieved if the resolutions of the input signal and the
projector panel are identical.
• If you connect this projector and a notebook computer, you need output the
display to an external monitor, or output simultaneously to the internal display
and an external monitor. Consult the computer's manual for the setting.
• Depending on the input signal, the automatic adjustment function of this
projector may take some time and not function correctly.
- Note that a composite sync signal or sync-on-green signal may confuse the
automatic adjustment function of this projector (&65).
- If the automatic adjustment function does not work correctly, you may not see
the dialog to set the display resolution. In such a case, use an external display
device. You may be able to see the dialog and set an appropriate display
resolution.
(continued on next page)
14
Setting up
Connecting with your devices (continued)
8962WU/8960W
External
device
Computer
USB
wireless
adapter
(optional)
Access
point
8961WU/8963
External
device
Computer
USB
wireless
adapter
(optional)
Access
point
(continued on next page)
15
Setting up
Connecting with your devices (continued)
WARNING ►Heat may build up in the USB wireless adapter, to avoid
possible burns disconnect the projector power cord for 10 minutes before
touching the adapter.
►When using the USB wireless adapter, use the supplied adapter cover or terminal
cover (&24).
CAUTION ► Before connecting the projector to a network system be sure
to obtain the consent of the administrator of the network.
►Do not connect the LAN port to any network that might have the excessive voltage.
►The designated USB wireless adapter that is sold as an option is required to use
the wireless network function of this projector. Before connecting the USB wireless
adapter, turn off the power of the projector and disconnect the power cord. Do not
use any extension cable or device when connecting the adapter to the projector.
►To connect both the LAN cable and USB wireless adapter to the projector, use
a LAN cable that is flat on the side where the plug’s wire is visible. Otherwise,
both of them cannot be connected correctly, or the wire may break (malfunction).
(continued on next page)
16
Setting up
Connecting with your devices (continued)
8962WU/8960W
VCR/DVD/
Blu-ray DiscTM
player
8961WU/8963
VCR/DVD/
Blu-ray DiscTM
player
(continued on next page)
17
Setting up
Connecting with your devices (continued)
About HDBaseT™ connection
• HDBaseT is a technology to transmit image, sound, ethernet or serial control
signal via LAN cable.
• Please go to the following URL regarding the device of other company that
supports HDBaseT and has been confirmed compatible with this projector.
www.dukaneav.com
LAN or HDBaseT input port can be selected as ethernet signal input by
switching in the menu.
• Use LAN cables of up to 100m long. Exceeding this length, the image
and sounds will be deteriorated, and even experience malfunction on LAN
transmission.
NOTE • The HDMI ports of this model are compatible with HDCP (High-bandwidth Digital Content Protection) and therefore capable of displaying video
signals from HDCP compatible DVD players or the like.
- The HDMI ports support the following signals:
For Video signals, refer to User’s Manual (detailed) Technical.
Audio signal : Format Linear PCM
Sampling frequency 48kHz / 44.1kHz / 32kHz
- This projector can be connected with another equipment that has HDMITM
connector, but with some equipment the projector may not work properly,
something like no video.
- Qualified cable is required for HDBaseT connection.
- Be sure to use an HDMITM cable that has the HDMITM logo.
- Use a Category 2-certified HDMITM cable to input 1080p@50/60 signal to the
projector.
- When the projector is connected with a device having DVI connector, use a
DVI to HDMITM cable to connect with the HDMITM input.
- The MHL supports the following signals.
For Video signals, refer to User’s Manual (detailed) Operating Guide –
Technical.
Audio signal : Format Linear PCM
Sampling frequency 48kHz / 44.1kHz / 32kHz
- Be sure to use an MHL cable that has the MHL logo.
• The HDMITM cables might come off easily due to the lack of a mechanical lock
on the cables and connectors. It is recommended to fasten the HDMI cables by
using the HDMI cable holder and the Cable tie to prevent them from coming off
(&22).
(continued on next page)
18
Setting up
Connecting with your devices (continued)
NOTE • This projector has HDMI input/output ports and can be connected to
multiple devices such as projectors or monitors with HDMI cable.
・The projected image is output when HDMI 1 / MHL or HDBaseT is selected.
・The resolution of the signal input to the projector and signal output from the
projector may be restricted by the maximum resolution of the connected device
such as projector or monitor.
・HDMI output operation in normal standby depends on the setting of the
menu (&74). It is not output during saving standby.
・When outputting HDMI signal, turn on the output side connected device
before inputting image signal to the projector.
・Up to 7 devices can be connected in series for HDMI output port of this
projector.
・The number of devices that can be connected varies depending on HDCP
version, the restriction of the number of devices for HDCP repetition of source
device, and the quality of a cable.
・The projected image from the projector may be interrupted when POWER
OFF/ON, input switching, or HDMI cable removal/insertion is executed on the
second or subsequent projector or monitor.
・When a device corresponding to MHL is connected to HDMI 1 / MHL port and
the state of a device connected to HDMI output port changes, selected input
port may be switched to HDMI 1 / MHL.
・HDMI output may be interrupted when the projector is turned on/off.
(continued on next page)
19
Setting up
Connecting with your devices (continued)
8962WU/8960W
Monitor
Speakers
(with an amplifier)
Another
projector
(Wired)
Remote
control
8961WU/8963
Monitor
Speakers
(with an amplifier)
Another
projector
(Wired)
Remote
control
(continued on next page)
20
Setting up
Connecting with your devices (continued)
NOTE • To use a wired remote control, connect a wired remote control to
the REMOTE CONTROL IN port. You can also connect another projector to
the REMOTE CONTROL OUT port to control it from the wired remote control.
You can utilize this projector as a remote control-relay with the REMOTE
CONTROL IN and OUT ports. To connect the wired remote control or another
projector to the REMOTE CONTROL IN or OUT ports, use audio cables with
3.5 mm diameter stereo mini plugs. This function is useful when a wireless
remote signal may not reliably reach the projector.
21
Setting up
Fastening the cables
Use the supplied cable tie to fasten the
cables.
Remove the screw located on the lower
side of HDMI connector and use it to
attach the HDMI cable holder.
screw
It is recommended to fasten the HDMI cables by using the HDMI cable holder and
the Cable tie to prevent them from coming off. Use a Cable tie with the size of 2.0
x 4.0mm or smaller.
No cable tie
HDMI cable
holder
With cable tie
cable tie
WARNING ►Do not fasten the cables other than HDMI.
CAUTION ►To fasten the cable, use a supplied Cable tie or plastic tie
with the size of 2.0 x 4.0mm or smaller. A metallic tie may cause damage to the
cables and tie holder.
►Do not bind the cables too tightly. The cables or the hole might be damaged.
22
Setting up
Fastening the adapter cover
When using the USB wireless adapter, use the supplied adapter cover for theft
prevention.
USB wireless adapter: USB-WL-11N
Temperature range: 0 ~ 45°C(operating)
1.
Loosen the screw on the bottom left of the WIRELESS port.
Insert the tab of the cover into the hole at the upper right of the WIRELESS
2. port in the direction of the arrow.
Tab
Align the screw holes on the projector and the cover. Then insert the screw
3. removed from the projector into the hole and tighten the screw.
WARNING ►Keep small parts away from children and pets. Take care not
to put in the mouth.
►Heat may build up in the USB wireless adapter, to avoid possible burns
disconnect the projector power cord for 10 minutes before touching the adapter.
23
Setting up
Attaching the terminal cover
Terminal cover
Hook
Claw
Insert the two claws of the Terminal cover into the hole of
the case and confirm Hook is fitting into the case.
When detaching the Terminal cover, push the Hook
in the direction of the arrow and pull it forward.
24
Setting up
Using the security bar and slot
Security slot
A commercially available anti-theft chain or
wire can be attached to the security bar on
the projector. Refer to the figure to choose
an anti-theft chain or wire.
Also this product has the security slot for
the Kensington lock.
For details, see the manual of the security
tool.
11mm
19mm
15mm
security bar
Anti-theft
chain or wire
WARNING ►Do not use the security slot to prevent the projector from
falling down, since it is not designed for it.
CAUTION ►Do not place anti-theft chain or wire near the exhaust vents.
It may become too hot.
NOTE • The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
When using the optional suspension bracket (HAS-9110), fix the bundled hook
metal and screws securely, and attach the drop-prevention chain.
Hook metal
・Pass the drop-prevention
chain through the hole of the
optional suspension bracket
and hook metal, and fix it
securely with a quick link.
Screw
Suspension bracket
(HAS-9110)
Drop-prevention chain
・Fix the drop-prevention
chain with a quick link so
that it cannot have any slack
as shown in the drawing.
25
Setting up
Connecting power supply
the connector of the power
1. Put
cord into the AC (AC inlet) of
the projector.
AC
plug the power cord’s plug into the
2. Firmly
outlet. In a couple of seconds after the power
Power
cord
supply connection, the POWER indicator will
light up in steady orange.
Please remember that when the DIRECT POWER ON function activated, the
connection of the power supply make the projector turn on.
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one. Never modify the power cord.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in fire, electric shock
or other accidents.
• Connect the ground terminal for the AC inlet of this unit to the ground terminal
of the building using an appropriate power cord (bundled).
NOTICE • This product is also designed for IT power systems with a phase-to
phase voltage of 220 to 240 V.
26
Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote
control starts to malfunction, try to replace the batteries. If you will not use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
1. Remove the battery cover.
and insert the two AA batteries
2. Align
according to their plus and minus terminals
3.
as indicated in the remote control. (Use
the appropriate AA carbon-zinc or alkaline
batteries (non-rechargeable) in accordance
with laws and regulations.)
Put the battery cover back to the former state.
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage, which
could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different types at
the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
27
Remote control
Changing the frequency of remote control signal
The accessory remote control has the two choices on signal frequency Mode
1:NORMAL and Mode 2:HIGH. If the remote control does not function properly,
attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of two buttons
listed below simultaneously for about 3 seconds.
(1)Set to Mode 1:NORMAL
VOLUME - and RESET buttons
(2)Set to Mode 2:HIGH
MAGNIFY OFF and ESC buttons
MAGNIFY
OFF button
ESC
button
(2)
INPUT
1
MYBUTTON
2
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
-
PAGE
UP
DOWN
+
GEOMETRY
+
PICTURE
INTERACTIVE NETWORK
ESC
+
MUTE
BLANK
MENU
ENTER
OSD MSG
RESET
(1)
VOLUME button
RESET
button
Please remember that the REMOTE
FREQ. in the SERVICE item of the OPTION menu (89) of the projector to be
controlled should be set to the same mode as the remote control.
28
Remote control
About the remote control signal
The remote control works with
the projector’s remote sensor.
This projector has a remote
sensor on the front.
The sensors can sense signals
within the following range:
60 degrees (30 degrees to the
left and right of the sensor)
within about 3 meters.
(approx.)
3m
30° 30°
NOTE • You can deactivate one of the sensors using the REMOTE RECEIV.
item in the SERVICE menu of the OPTION menu (89).
• The remote control signal reflected in the screen or the like may be available.
If it is difficult to send the signal to the sensor directly, attempt to make the
signal reflect.
• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.
• The remote control may not work correctly if strong light (such as direct
sun light) or light from an extremely close range (such as from an inverter
fluorescent lamp) shines on the remote sensor of the projector. Adjust the
position of projector avoiding those lights.
29
Power on/off
Power on/off
Turning on the power
STANDBY/ON button
POWER indicator
sure that the power cord is
1. Make
firmly and correctly connected to the
projector and the outlet.
sure that the POWER indicator is
2. Make
lighted in steady orange (112). Then
remove the lens cover.
INPUT
ASPECT
1
MYBUTTON
1
ASPECT
PbyP
MAGNIFY
ON
DOWN
3.
FOCUS
+
OFF
ZOOM
+
-
GEOMETRY
-
PICTURE
INTERACTIVE NETWORK
ESC
2
2
AUTO
PbyP
PAGE
UP
MAGNIFY
ON
MYBUTTON
INPUT
FREEZE
VOLUME
+
AUTO
-
BLANK
MENU
FOCUS
FREEZE
MUTE
ZOOM
VOLUME
Press the STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and POWER indicator will begin blinking in
green. When the power is completely on, the indicator will stop blinking and
light in steady green (112).
+
+
ENTER
OSD MSG
+
RESET
OFF
PAGE
UP
DOWN
GEOMETRY
PICTURE
INTERACTIVE NETWORK
MUTE
BLANK
To display the picture, select an input signal according to the section Selecting an
input signal (33).
ESC
MENU
The INITIAL SETTING Menu will be displayed by factory default upon startup.
Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET
(94) is executed. If you wish to change the settings, refer to the LANGUAGE
(76) and ALTITUDE (88) menu.
ENTER
OSD MSG
(1) LANGUAGE: Use the ▲/▼/◄/►buttons to
select the desired language and press the
ENTER button of the remote control or the
INPUT button of the projector to execute.
(2) ALTITUDE: Use the ▲/▼ buttons to select
NORMAL for altitude below 1600 m (5250 feet),
otherwise select HIGH and press the ENTER
button of the remote control or the INPUT button
of the projector to execute.
(continued on next page)
30
RESET
Power on/off
Turning off the power
the STANDBY/ON button on the projector or the remote control.
1. Press
The message “Power off?” will appear on the screen for about 5 seconds.
the STANDBY/ON button again while the message appears.
2. Press
The projector lamp will go off, and the POWER indicator will begin blinking
in orange. Then the POWER indicator will stop blinking and light in steady
orange when the lamp cooling is complete (112).
3. Attach the lens cover, after the POWER indicator turns to steady orange.
Do not turn the projector on for about 10 minutes or more after turning it off.
Also, do not turn the projector off shortly after turning it on. Such operations might
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING ►A strong light is emitted when the projector’s power is on.
Do not look into the lens of the projector or look inside of the projector through
any of the projector’s openings since the projection ray may cause a trouble on
your eyes.
►Keep any object away from concentrated projection light beam. Blocking the
beam by something causes high temperature and could result in fire or smoke.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
NOTE • Turn the power on/off in right order. Please power on the projector
prior to the connected devices.
• This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON (83) and AUTO POWER OFF (83)
items of the OPTION menu.
31
Operating
Operating
Adjusting the volume
MYBUTTON
INPUT
1
ASPECT
PbyP
AUTO
FREEZE
FOCUS
ZOOM
VOLUME
-
-
Use the VOLUME + / - buttons to adjust the volume.
A dialog will appear on the screen to aid you in
adjusting the volume. If you do not do anything, the
dialog will automatically disappear after a few seconds.
MAGNIFY
ON
INPUT
1
MYBUTTON
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
-
OFF
PAGE
UP
DOWN
+
GEOMETRY
+
PICTURE
INTERACTIVE NETWORK
ESC
PAGE
UP
+
+
2
ASPECT
2
+
VOLUME + / -
+
MUTE
-
buttons
BLANK
MENU
ENTER
GEOMETRY
OSD MSG
DOWN
PICTURE
MUTE
RESET
INTERACTIVE NETWORK
BLANK
NOTE • When is selected for current picture input port, the volume
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (75).
• Even if the projector is in the standby mode, the volume is adjustable when
both of the following conditions are true:
- An option other than is selected for AUDIO OUT in the STANDBY
OUTPUT item of the SETUP menu (74).
- NORMAL is selected in the STANDBY MODE item of the SETUP menu (72).
ESC
MENU
ENTER
RESET
OSD MSG
INPUT
Temporarily muting the sound
MYBUTTON
1
2
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
Press MUTE button on the remote control.
A dialog will appear on the screen indicating
that you have muted the sound.
To restore the sound, press the MUTE, VOLUME +
or VOLUME - button. Even if you do not do anything,
the dialog will automatically disappear after a few seconds.
+
OFF
INPUT
ASPECT
PAGE
UP
1
MYBUTTON
PbyP
MAGNIFY
ON
FOCUS
OFF
-
PAGE
UP
DOWN
FREEZE
ZOOM
VOLUME
OSD MSG
-
+
GEOMETRY
GEOMETRY
-
+
2
AUTO
+
+
-
PICTURE
INTERACTIVE NETWORK
ESC
DOWN
+
-
PICTURE
MUTE
MUTE
BLANK
MENU
INTERACTIVE NETWORK
ENTER
BLANK
MUTE
button
RESET
ESC
MENU
ENTER
NOTE • When is selected for current picture input port, the sound is always
muted.
Please see AUDIO SOURCE item of AUDIO menu (75).
• C.C. (Closed Caption) is automatically activated when sound is muted and an
input signal containing C.C. is received. This function is available only when the
signal is NTSC for VIDEO or COMPUTER IN, and when AUTO is selected for
DISPLAY in the C.C. menu under the SCREEN menu (81).
OSD MSG
32
RESET
Operating
Selecting an input signal
INPUT button
Press INPUT button on the projector or the remote
control. Select a desirable input referring to the
displayed input list.
LAN  COMPUTER IN  HDMI 1 / MHL
VIDEO
HDBaseT*
* 8962WU/8960W/ only

HDMI 2
INPUT
INPUT
1
MYBUTTON
ASPECT
PbyP
MAGNIFY
ON
FOCUS
OFF
PAGE
UP
DOWN
+
FREEZE
ZOOM
VOLUME
+
-
GEOMETRY
2
AUTO
-
PICTURE
INTERACTIVE NETWORK
ESC
+
1
MYBUTTON
2
INPUT button
-
MUTE
BLANK
ASPECT
PbyP
MAGNIFY
ON
FOCUS
AUTO
FREEZE
ZOOM
VOLUME
MENU
ENTER
OSD MSG
RESET
+
+
+
NOTE • If you have set SKIP to some ports from SOURCE SKIP -in the
OPTION menu, the input from the ports cannot be selected (82).
• While ON is selected for AUTO SEARCH item in OPTION menu, the projector
will keep checking the ports in above order repeatedly till an input signal is
detected (82).
OFF
PAGE
UP
DOWN
GEOMETRY
PICTURE
INTERACTIVE NETWORK
ESC
MUTE
BLANK
MENU
ENTER
OSD MSG
RESET
33
Operating
Selecting an aspect ratio
Press ASPECT button on the remote control.
Each time you press the button, the projector
switches the mode for aspect ratio in turn.
INPUT
ASPECT
INPUT
1
MYBUTTON
ASPECT
PbyP
MAGNIFY
ON
FOCUS
OFF
PAGE
UP
DOWN
+
FREEZE
ZOOM
VOLUME
+
-
GEOMETRY
2
AUTO
-
PICTURE
INTERACTIVE NETWORK
ESC
+
-
MUTE
1
MYBUTTON
PbyP
2
AUTO
FREEZE
ASPECT button
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
-
+
+
+
BLANK
MENU
ENTER
OSD MSG
RESET
or a computer signal
F
8963:
NORMAL  4:3  16:9  16:10  ZOOM
8961WU, 8960W, 8962WU:
NORMAL  4:3  16:9  16:10  ZOOM  NATIVE
PAGE
UP
DOWN
GEOMETRY
PICTURE
INTERACTIVE NETWORK
ESC
F
or HDMITM , HDBaseTTM and MHL signals
8963:
NORMAL  4:3  16:9  16:10  14:9  ZOOM
8961WU, 8962WU, 8960W:
NORMAL  4:3  16:9  16:10  14:9  ZOOM  NATIVE
BLANK
MENU
ENTER
OSD MSG
F
or a video signal
8963:
4:3  16:9  14:9  ZOOM
8961WU, 8962WU, 8960W:
4:3  16:9  16:10  14:9  ZOOM  NATIVE
F
or an input signal from the LAN port, or if there is no signal
8963: 4:3 (fixed)
8961WU, 8962WU, 8960W: 16:10 (fixed)
NOTE • ASPECT button does not work when no proper signal is input.
• NORMAL mode keeps the original aspect ratio setting.
34
MUTE
RESET
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly
uneven to the left or right, use the elevator feet to
place the projector horizontally. Using the feet can
also tilt the projector in order to project at a
11°
suitable angle to the screen, elevating the front
side of the projector within 11 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is
adjustable while pushing the elevator button on the same side as it.
Holding the projector, push the elevator buttons to loose the elevator feet.
1.
2.
3.
Position the front side of the projector to the desired height.
Release the elevator buttons in order to lock the elevator feet.
After making sure that the elevator feet are locked, put the projector down
4. gently.
If necessary, the elevator feet can be manually twisted to make more precise
5. adjustments. Hold the projector when twisting the feet.
To loose an elevator foot,
push the elevator button
on the same side as it.
To finely adjust,
twist the foot.
CAUTION ►Do not handle the elevator buttons without holding the
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 11 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
Adjusting the zoom and focus
1.
2. Use the FOCUS ring to focus the picture.
Use the ZOOM ring to adjust the screen size.
ZOOM ring
FOCUS ring
35
Operating
Adjusting the lens shift
the VERTICAL adjuster fully counter
1. Turn
clockwise. Then turn it clockwise and
VERTICAL adjuster
HORIZONTAL adjuster
adjust the vertical lens position upward.
the HORIZONTAL adjuster clockwise
2. Turn
or counter clockwise to adjust the
horizontal lens position.
V50%
V
H
H5% :8960W/8961WU/8963
H4.4%:8962WU/8961WU
CAUTION ►Operate the lens adjusters gently as the lens may malfunction
when subjected to shocks. It may need more strength to turn the adjusters near
the adjustment limits. Be careful not to apply too much strength. If the lens adjuster
is turned excessively, it runs idle by a clutch mechanism inside the adjuster.
Although it makes a clicking sound, it is not a malfunction. When the lens adjuster
runs idle, the lens shift cannot be performed further. Turn the lens adjuster to the
opposite direction to adjust the lens shift. When the lens adjuster is turned too
quickly, it may make a clicking sound by a clutch mechanism. In that case, turn it
slowly to adjust the lens shift.
・When adjusting the lens shift to the maximal oblique direction, the periphery of
the projected screen may be dark or a shadow may be cast.
・When adjusting the lens shift vertically, perform it by moving the projected
screen upward. If adjusting the lens shift by moving the projected screen
downward, the projected screen may be adjusted slightly low.
NOTE • When the lens adjuster runs idle
with a clicking sound and it still makes a sound
by a clutch mechanism even if it is turned to the
opposite direction, turn the lens adjuster while
pressing it downward to perform the lens shift.
36
Operating
Using the automatic adjustment feature
INPUT
1
MYBUTTON
2
Press AUTO button on the remote control.
AUTO
FREEZE
ASPECT
PbyP
Pressing this button performs the following.
AUTO button
MAGNIFY
VOLUME
FOCUS
ZOOM
F
or a computer signal
ON
+
+
+
The vertical position, the horizontal position and the
OFF
horizontal phase will be automatically adjusted.
Make sure that the application window is set to its
PAGE
GEOMETRY
PICTURE
MUTE
maximum size prior to attempting to use this feature. A UPdark
picture
may
still be
incorrectly adjusted. Use a bright picture when adjusting.
BLANK
DOWN INTERACTIVE NETWORK
F
or a video signal
The video format best suited for the respective input signal will be selected
ESC
MENU
automatically. This function is available only when the AUTO is selected for
the VIDEO FORMAT item in the INPUT menu (64). The vertical position and
horizontal position will be automatically set to the default.
ENTER
 For a component video signal
The vertical position and horizontal position will be automatically set to the default.
RESET
The horizontal phase will be automatically adjusted. OSD MSG
INPUT
1
MYBUTTON
ASPECT
PbyP
MAGNIFY
ON
FOCUS
OFF
-
PAGE
UP
DOWN
+
GEOMETRY
2
AUTO
FREEZE
ZOOM
VOLUME
+
-
PICTURE
INTERACTIVE NETWORK
ESC
+
-
MUTE
BLANK
MENU
ENTER
OSD MSG
RESET
NOTE • The automatic adjustment operation requires approx. 10 seconds. Also
please note that it may not function correctly with some input.
• When this function is performed for a video signal, a certain extra such as a line
may appear outside a picture.
• When this function is performed for a computer signal, a black frame may be
displayed on the edge of the screen, depending on the computer model.
• The items adjusted by this function may vary when the FINE or DISABLE is selected
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (88).
37
Operating
Correcting the distortion
MYBUTTON
INPUT
1
ASPECT
PbyP
2
AUTO
FREEZE
To correct the distortion of projected screen, you can select one of three
options,
+
+
+
KEYSTONE, PERFECT FIT, and WARPING. First press the GEOMETRY button
to display the GEOMETRY CORRECTION menu, and point at one of
the
- items
with the ▲/▼ buttons.
GEOMETRY
KEYSTONE: a
llows you to adjust the vertical and
button
horizontal keystone.
PERFECT FIT: a
llows you to adjust each of the screen
corners and sides to correct the
distortion.
WARPING: a
llows you to project an image on several
types of screen.
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
GEOMETRY
PICTURE
MUTE
OFF
INPUT
ASPECT
MAGNIFY
ON
OFF
PAGE
UP
DOWN
1
MYBUTTON
AUTO
PbyP
FOCUS
+
ZOOM
+
-
GEOMETRY
PAGE
UP
-
PICTURE
INTERACTIVE NETWORK
ESC
FREEZE
VOLUME
+
-
MUTE
BLANK
MENU
ENTER
OSD MSG
2
DOWN
INTERACTIVE NETWORK
BLANK
RESET
ESC
MENU
ENTER
Use KEYSTONE / PERFECT FIT / WARPING for adjustment. When one of
them is selected, other items are not available.
OSD MSG
RESET
Then follow the procedure shown below for the item you selected.
NOTE • The menu or dialog will automatically disappear after several seconds
of inactivity. Press the GEOMETRY button again, or point the cursor at EXIT in
the dialog and press the ►or ENTER button to end the operation and close the
menu or dialog.
 KEYSTONE:
When KEYSTONE is pointed at, pressing the ► or
ENTER button displays the KEYSTONE dialog.
1.
2.
Select the vertical or horizontal keystone ( / )
with the ▲/▼ buttons.
Use the ◄/► buttons to adjust the keystone distortion.
NOTE • When the zoom adjustment is set to the TELE (telephoto focus),
this function may be excessive. This function should be used when the zoom
adjustment is set to the full WIDE (wide-angle focus) whenever possible.
• When the horizontal lens shift is not set to the center, this function may not
work well.
• Point at RETURN in the dialog with the ▲/▼ buttons and press ◄ or ENTER
button to return to the GEOMETRY CORRECTION menu.
38
Operating
Correcting the distortion (continued)
 PERFECT FIT:
When PERFECT FIT is pointed at, pressing the
► or ENTER button displays the PERFECT FIT
dialog.
This projector is equipped with a test pattern for
PERFECT FIT. Select PATTERN with the ▲/▼
buttons, then press the ◄/► buttons to switch on
and off.
Select SETUP with the ▲/▼ buttons and
press the ► or ENTER button.
Select one of the corners or sides to be adjusted
with the ▲/▼/◄/► buttons and press the
ENTER or
button.
Adjust the selected part as below.
1.
2.
3.
● For adjusting a corner, use the ▲/▼/◄/► buttons to adjust the position of
the corner.
● For adjusting the upper or lower side, use the ▲/▼ buttons to adjust the
distortion of the side.
● For adjusting the left or right side, use the ◄/► buttons to adjust the
distortion of the side.
button and follow
● To adjust another corner or side, press the ENTER or
the procedure from step 2.
(continued on next page)
39
Operating
Correcting the distortion (continued)
projector is equipped with a memory feature for PERFECT FIT
4. This
adjustment. Up to 3 sets of adjustments can be stored.
● SAVE:
To store the current PERFECT FIT adjustment, select one of the "SAVE"
options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and
press the ►, ENTER or
button.
Remember that the current data being stored of a memory will be lost by
saving new data into the memory.
● LOAD:
To recall stored adjustments, select one of the "LOAD" options numbered
1 to 3 (number of the memory) with the ▲/▼ buttons and press the ►,
ENTER or
button.
Remember that the current adjusted condition will be lost by loading data. If
you want to keep the current adjustment, please save it before performing a
LOAD function.
NOTE • The LOAD functions whose linked memory has no data are skipped.
• There may be some noise and the screen may flicker for a moment when
loading data. This is not malfunction.
ARPING:
W
Projection on several types of screen can be performed by WARPING function.
This function is operated by using dedicated PC tool, "Warping Tool".
PC and projector are required to be connected with LAN cable in order to use
this function.
You can get the PC tool from the URL below.
http://www.hitachi.co.jp/proj/
Refer to Application Manual for operations.
40
Operating
Using the EDGE BLENDING features
1. MODE (MANUAL)
OFF: Disables the Blending function.
MANUAL: Allows you to adjust Blending Region or Blending Level by using menu.
• IMAGE OPTIMIZER is not selectable when Blending is set to other than OFF.
• ECO MODE is not selectable when Blending is set to other than OFF.
2. BLENDING LEVEL
Select BLENDING LEVEL with ▲/▼ buttons.
[1-25] can be selected with ◄/► buttons.
Adjust the brightness of Blending Region according to the settings.
3. BLENDING REGION
3.1 Specifying Blending Region
Select one of the four sides with ▲/▼/◄/► buttons and press ENTER or
button. Blending Region can be specified for left and right sides with ◄/►
buttons and for top and bottom sides with ▲/▼ buttons.
Specify Blending Region for each projector.
Adjust them referring to the guide displayed during the adjustment of Blending
Region.
Blend Region
* The minimum value
Blending Region is 200 dots.
LeftofImage
Right Image
Guide line
(continued on next page)
41
Operating
4. CROPPING
When inputting the same image to each projector, Cropping function enables
projector to cut out a part of input image and display one image on a large
screen. The following patterns are supported.
2x1
1x2
2x2
.1 Displaying Cropping Menu
4
Select CROPPING with ▲/▼ buttons and press ►,
ENTER or
button to display Cropping Menu.
4.2 Setting Cropping
Select MODE with ▲/▼ buttons and select ON with
◄/► buttons.
Input image is automatically cut out according to the
settings of Blending Region.
(continued on next page)
42
Operating
4.3 Adjusting Cropping Area
Adjust Cropping Area when cutting out a part of input image.
Select SETUP with ▲/▼ buttons and press ►, ENTER or
button.
* MODE is set to [OFF] temporarily and the guide of Cropping Area
is displayed.
Select [LT]/[WH] with ▲/▼ buttons and press ENTER or
button.
Move the guide display with ▲/▼/◄/► buttons to select the region of the
screen to be cut out.
Press ENTER or
button and then press ◄ button to select SETUP, and
MODE switches to ON automatically.
Input Image
Cropping
4.4 Adjust Cropping Area of the other projector.
Set Cropping Area of the other projector with the same value as one projector.
Input image is automatically cut out according to the settings of Blending
Region.
* When you want to keep input image from not being seen while setting up, set
BLANK to ON.
Input Image
Cropping
(continued on next page)
43
Operating
5. DIMMING LEVEL
Adjusts the brightness of the projectors which are using Blending.
Using the ◄/► buttons to adjust the dimming level.
6. WHITE BALANCE
Adjusts the white balance of the whole screen.
6.1 OFFSET
OFFSET adjustments change the color intensity on the whole tones.
6.2 GAIN
GAIN adjustments mainly affect color intensity on the brighter tones.
NOTE • The positional deviation of the screen may occur after installing
the projector over time. In that case, perform the screen adjustment again to
correct the positional deviation.
44
Using the magnify feature
the MAGNIFY ON button on the remote
1. Press
control.
The picture will be magnified, and the MAGNIFY
dialog will appear on the screen. When the
MAGNIFY ON button is pressed for the first time
after the projector is turned on, the picture will be
zoomed by 1.5 times. On the dialog, triangle marks
to show each direction will be displayed.
INPUT
1
MYBUTTON
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
PAGE
UP
DOWN
+
+
-
GEOMETRY
-
PICTURE
INTERACTIVE NETWORK
ESC
1
ASPECT
PbyP
MAGNIFY
ON
2
ASPECT
+
-
MUTE
BLANK
OFF
MENU
FOCUS
+
AUTO
FREEZE
ZOOM
VOLUME
+
+
MAGNIFY
ON/OFF
button
-
ENTER
OSD MSG
RESET
display magnification of the projector switches in order
2. The
with every press of the MAGNIFY ON button.
PAGE
UP
DOWN
GEOMETRY
PICTURE
INTERACTIVE NETWORK
ESC
MUTE
BLANK
MENU
ENTER
or computer signals, HDMI (RGB) signals, HDBaseT
F
input signals from the LAN port
1.5times  2 times  3 times  4 times  1 time
TM
2
Operating
MYBUTTON
INPUT
TM
signals,
OSD MSG
RESET
F
or video signals, HDBaseT signals, MHL signals or HDMITM signals
1.5times  2 times  1 time
the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor
3. While
buttons to shift the magnifying area.
4. Press the MAGNIFY OFF button on the remote control to exit magnification.
NOTE • The MAGNIFY dialog will automatically disappear in several seconds
with no operation. The dialog will appear again if the MAGNIFY ON button is
pressed when the dialog has automatically disappeared.
• The magnification is automatically disabled when the displaying signal or its
display condition is changed.
• While the magnification is active, the keystone distortion condition may vary. It
will be restored when the magnification is disabled.
• Some horizontal stripes might be visible on the image while magnification is
active.
• This function is not available in the following cases:
-A sync signal in the range not supported is input.
-There is no input signal.
45
Operating
Temporarily freezing the screen
INPUT
Press the FREEZE button on the remote control.
The “FREEZE” indication will appear on the screen
(however, the indication will not appear when
SILENT is selected for the OSD MESSAGE item
in the SETUP (73)), and the projector will go into the
FREEZE mode, which the picture is frozen.
To exit the FREEZE mode and restore the screen to
normal, press the FREEZE button again.
ASPECT
MAGNIFY
ON
MYBUTTON
1
PbyP
INPUT
1
MYBUTTON
2
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
-
PAGE
UP
+
GEOMETRY
+
PICTURE
DOWN
MUTE
+
INTERACTIVE NETWORK
AUTO
FREEZE
ZOOM
VOLUME
-
-
+
FOCUS
ESC
2
BLANK
+
MENU
FREEZE
button
+
ENTER
RESET
OSD MSG
OFF
PAGE
UP
DOWN
-
GEOMETRY
PICTURE
INTERACTIVE NETWORK
MUTE
BLANK
NOTE • The projector automatically exits from the FREEZE mode when some
control buttons are pressed.
• If the projector continues projecting a still image for a long time, the LCD
panel might possibly be burned in. Do not leave the projector in the FREEZE
mode for too long.
• Images might appear degraded when this function is operated, but it is not a
malfunction.
ESC
Temporarily blanking the screen
Press BLANK button on the remote control.
The BLANK screen will be displayed instead of
the screen of input signal. Please refer to BLANK
item in SCREEN menu (76).
To exit from the BLANK screen and return to the
input signal screen, press BLANK button again.
MENU
ENTER
MYBUTTON
INPUT
1
ASPECT
OSD MSG
PbyP
MAGNIFY
ON
OFF
PAGE
UP
AUTO
FREEZE
RESET
FOCUS
ZOOM
VOLUME
-
-
-
+
GEOMETRY
INPUT
1
MYBUTTON
ASPECT
PbyP
MAGNIFY
ON
FOCUS
OFF
DOWN
2
+
PICTURE
FREEZE
ZOOM
VOLUME
+
DOWN
GEOMETRY
-
PICTURE
INTERACTIVE NETWORK
ESC
MUTE
+
-
INTERACTIVE NETWORK
PAGE
UP
+
2
AUTO
-
+
MUTE
BLANK
BLANK
MENU
ENTER
ESC
OSD MSG
RESET
MENU
BLANK
button
ENTER
• The projector automatically exits from the BLANK mode when some control
buttons are pressed.
OSD MSG
RESET
CAUTION ►If you wish to have a blank screen while the projector's lamp
is on, use the BLANK function above.
Taking any other action may cause the damage on the projector.
NOTE • The sound is not connected with the BLANK screen function. If
necessary, set the volume or mute first.
46
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture)
The PbyP / PinP is a function for displaying two different picture signals on a
screen that is separated into main and sub areas for each signal.
INPUT
1
1
ASPECT
PbyP
MYBUTTON
2
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
OFF
-
-
-
PAGE
UP
DOWN
ESC
MYBUTTON
INPUT
+
+
GEOMETRY
PbyP
AUTO
FREEZE
button
+
PICTURE
MUTE
MAGNIFY
ON
INTERACTIVE NETWORK
BLANK
MENU
2
FOCUS
ZOOM
VOLUME
-
-
-
+
+
ð
main
area
sub
area
ð
main
area
+
ENTER
OSD MSG
RESET
OFF
Normal mode
PbyP mode
PinP mode
sub area
Press the PbyP button on the remote control. This acctivates the PbyP mode.
Then, press the PbyP button again. The projector goes into PinP mode. The
screen displayed before the PbyP button was pressed will be displayed as the
main area. Most of operations are effective for the main area only. Only outputs
the audio input signal paired with the picture input signal for the main area.
To quit the PinP mode, press the PbyP button again.
PAGE
UP
DOWN
GEOMETRY
PICTURE
INTERACTIVE NETWORK
ESC
MUTE
BLANK
MENU
ENTER
NOTE • If the LAN port is selected when the PbyP button is pressed, input
from other port is displayed on the main area.
• When in the PbyP / PinP mode, use the MENU button on the remote control
or ▲/▼ buttons on the control panel to display the OSD menu.
• There are certain functions that cannot be used when in the PbyP / PinP mode.
• A message will be displayed when buttons that cannot be used are pressed
(111). However, note that there are certain unusable buttons for which
messages are not displayed.
• The functions on the OSD menu that cannot be used are displayed in gray
and cannot be selected.
OSD MSG
RESET
(continued on next page)
47
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
etting information
S
The setting information will be appeared for several seconds when the PbyP /
PinP function is started. Displays the input information for each area. A frame
around the main area and an audio mark indicating the audio output will also be
displayed. The information can be redisplayed with the ◄/► buttons after it has
been erased.
Audio mark
Audio mark
Frame
main area
main area sub area
Frame
sub area
Input information
Input information
PbyP mode
PinP mode
C
hanging the main area
The position of the main area can be toggled with the ◄/► buttons when the
setting information is displayed on the screen. The frame and the audio mark will
move together with it.
main
area
sub
area
PbyP mode
(continued on next page)
48
sub
area
main
area
main area
sub area
sub area
PinP mode
main area
Operating
PbyP (Picture by Picture) / PinP(Picture in Picture) (continued)
LAN
HDMI 1 / MHL
HDMI 2
HDBaseT *
VIDEO
Sub area
COMPUTER IN
C
hanging the picture input signal
Press any button to select an input port on the remote control or press the
INPUT button on the control panel. A dialog box to select the input signal for
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To
change the signal in the sub area, switch temporarily across to the main area
with the ◄/► buttons.
Displaying the same signal on the both areas is not allowed. Refer to the table
for details on available input signal combinations. Any combinations marked
with "X" cannot be selected.
COMPUTER IN X
X
O
O
O
X
LAN X
X
X
X
X
X
HDMI 1 / MHL O
X
X
O
X
O
Main area
HDMI 2 O
X
O
X
O
O
HDBaseT * O
X
X
O
X
O
VIDEO X
X
O
O
O
X
* 8962W/8960W only
main area sub area
Input signal
PbyP mode
main area
Input signal
sub area
PinP mode
NOTE • The combined input signals marked with an "O" can be selected and
displayed in the PbyP / PinP mode even when the port is set to SKIP with the
SOURCE SKIP on the OPTION menu (82).
(continued on next page)
49
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
P
byP /PinP SWAP function
Press the MY BUTTON assigned the PbyP / PinP SWAP (84). The position of
the both area is exchanged without any setting change.
main
area
sub
area
sub
area
main
area
sub area
PbyP mode
sub area
main area
PinP mode
main area
NOTE • For some signals, it may not be displayed correctly in the PbyP / PinP
mode, even if it can be displayed properly in the normal mode.
• PbyP/PinP is unavailable when MANUAL is selected in GEOMETRY
CORRECTION > EDGE BLENDING > MODE.
C
hanging the size of main area in PbyP mode
Using ▲/▼ buttons on the remote control changes the size of main area in
PbyP mode.
main area
sub area
main area sub area
main area
sub area
C
hanging the position of sub area in PinP mode
1. Select INPUT MENU > PbyP / PinP SETUP > PinP POSITION (67).
2. Using ▲/▼ buttons on the remote control changes the position of sub area
in PinP mode.
main area
sub area
50
main area
sub area
main area
sub area
main area
sub area
Operating
Using the menu function
This projector has the following menus:
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK,
SECURITY and EASY MENU. EASY MENU consists of functions often used, and
the other menus are+ classified
into each purpose and brought together as the
+
+
ADVANCED MENU.
Each of these menus
using the same methods. While the projector
- is -operated
is displaying any menu, the MENU button on the projector works as the cursor
buttons. The basic operations of these menus are as follows.
MYBUTTON
INPUT
1
ASPECT
PbyP
AUTO
FREEZE
MAGNIFY
ON
FOCUS
ZOOM
VOLUME
GEOMETRY
PICTURE
MUTE
2
OFF
PAGE
UP
DOWN
INTERACTIVE NETWORK
ESC
INPUT
1
MYBUTTON
ASPECT
PbyP
MAGNIFY
ON
FOCUS
OFF
PAGE
UP
DOWN
+
FREEZE
ZOOM
VOLUME
+
-
PICTURE
INTERACTIVE NETWORK
ESC
MENU button
INPUT button
MENU
Cursor buttons
2
AUTO
-
GEOMETRY
BLANK
+
-
MUTE
ENTER
BLANK
MENU
ENTER
OSD MSG
RESET
OSD MSG
ENTER button
RESET
RESET button
start the MENU, press the MENU button. The MENU you last used (EASY
1. To
or ADVANCED) will appear. EASY MENU has priority to appear just after
powered on.
EASY MENU
2. In(1)the
Use the ▲/▼ cursor buttons to select an item to
operate. If you want to change it to the ADVANCED
MENU, select the ADVANCED MENU.
(2) Use the ◄/► cursor buttons to operate the item.
In the ADVANCED MENU
(1) Use the ▲/▼ cursor buttons to select a menu.
If you want to change it to the EASY MENU, select
the EASY MENU.
The items in the menu appear on the right side.
(2) Press the ► cursor button or ENTER button to
move the cursor to the right side. Then use the
▲/▼ cursor buttons to select an item to operate and press the ► cursor
button or ENTER button to progress. The operation menu or dialog of the
selected item will appear.
(3) Use the buttons as instructed in the OSD to operate the item.
(continued on next page)
51
Operating
Using the menu function (continued)
close the MENU, press the MENU button again or select EXIT and press
3. To
the ◄ cursor button or ENTER button. Even if you do not do anything, the
dialog will automatically disappear after about 30 seconds.
NOTE • Some functions cannot be performed when a certain input port is
selected, or when a certain input signal is displayed.
• When you want to reset the operation, press RESET button on the remote
control during the operation. Note that some items (ex. LANGUAGE, VOLUME)
cannot be reset.
• In the ADVANCED MENU, when you want to return to the previous display,
press the ◄ cursor button on the remote control.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
Indication
Meaning
EXIT
Selecting this word finishes the OSD menu. It's the same as
pressing the MENU button.
RETURN
Selecting this word returns the menu to the previous menu.
CANCEL or NO
OK or YES
52
Selecting this word cancels the operation in the present
menu and returns to the previous menu.
Selecting this word executes the prepared function or shifts
the menu to the next menu.
Operating
Using the menu function (continued)
Containing items of each menu
The items contained in the menus are as below;
Menu
Items
EASY MENU (54)
ASPECT, KEYSTONE, PERFECT FIT, PICTURE MODE,
ECO MODE, INSTALLATION, RESET, FILTER TIME,
LANGUAGE, ADVANCED MENU, EXIT
PICTURE(56)
BRIGHTNESS, CONTRAST, COLOR, TINT, SHARPNESS,
ACTIVE IRIS, PICTURE QUALITY, MY MEMORY
IMAGE (60)
ASPECT, OVER SCAN, V POSITION, H POSITION, H PHASE,
H SIZE, AUTO ADJUST EXECUTE
INPUT (63)
PROGRESSIVE, VIDEO NR, COLOR SPACE,
VIDEO FORMAT, DIGITAL FORMAT, DIGITAL RANGE,
COMPUTER IN, FRAME LOCK, RESOLUTION,
PbyP/PinP SETUP, MHL STANDBY PWR.
SETUP (68)
GEOMETRY CORRECTION, LAMP & FILTER, IMAGE OPTIMIZER,
PICTURE POSITION, INSTALLATION, STANDBY MODE,
COLOR UNIFORMITY, OSD MESSAGE, HDMI OUTPUT,
STANDBY OUTPUT
AUDIO (75)
VOLUME, SPEAKER, AUDIO SOURCE
SCREEN(76)
LANGUAGE, MENU POSITION, BLANK, AUTO BLANK,
START UP, MyScreen, MyScreen Lock, SOURCE NAME,
TEMPLATE, C.C.
OPTION (82)
SOURCE SKIP, AUTO SEARCH, DIRECT POWER ON,
AUTO POWER OFF, SHADE TIMER, MY BUTTON,
SCHEDULE, SERVICE
NETWORK (95)
NETWORK INFORMATION, WIRELESS NETWORK,
NETWORK SETUP, MY IMAGE, EXTERNAL CONTROL,
OTHER OPERATION
SECURITY (96)
ENTER PASSWORD, SECURITY PASSWORD CHANGE,
MyScreen PASSWORD, PIN LOCK, TRANSITION DETECTOR,
MY TEXT PASSWORD, MY TEXT DISPLAY, MY TEXT WRITING,
SECURITY INDICATOR, STACK LOCK
53
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then
perform it according to the following table.
Item
ASPECT
KEYSTONE
PERFECT FIT
Description
Using the ◄/► buttons switches the mode for aspect ratio.
See the ASPECT item in IMAGE menu (60).
Pressing the ► button displays the KEYSTONE dialog.
See the KEYSTONE item in SETUP menu (68).
Pressing the ► button displays the PERFECT FIT dialog.
See the PERFECT FIT item in SETUP menu (68).
Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP
settings. Choose a suitable mode according to the projected source.
PICTURE MODE
STANDARD ó NATURAL ó CINEMA ó DYNAMIC


USER-3
BOARD(BLACK)


USER-2
BOARD(GREEN)


USER-1 ó DICOM SIM. ó DAYTIME ó WHITEBOARD
• Lines or other noise might appear on the screen when this function
is operated, but it is not a malfunction.
• DICOM SIM. is the projector's DICOM® ("Digital Imaging and
Communication in Medicine") simulation mode. This mode
simulates the DICOM standard, which is a standard applicable to
digital communications in medicine, and can be useful for displaying
medical images, such as X-rays photos. This projector is not a
medical device and is not compliant to the DICOM standard, and
neither the projector nor the DICOM SIM. mode should be used for
medical diagnosis.
(continued on next page)
54
EASY MENU
Item
ECO MODE
INSTALLATION
Description
Using the ◄/► buttons turns off/on the Eco mode.
See the ECO MODE item in SETUP menu (69).
Pressing the ► button displays the INSTALLATION dialog.
See the INSTALLATION item in SETUP menu (71).
RESET
Performing this item resets all of the EASY MENU items except the
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting the OK using the ►
button performs resetting.
FILTER TIME
The usage time of the air filter is shown in the menu.
Performing this item resets the filter time which counts usage time
of the air filter.
A dialog is displayed for confirmation. Selecting the OK using the ►
button performs resetting.
See the FILTER TIME item in SETUP menu (70).
LANGUAGE
Using the ◄/► buttons changes the display language.
See the LANGUAGE item in SCREEN menu (76).
Press the ► or ENTER button to use the menu of PICTURE,
ADVANCED MENU IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or
SECURITY.
EXIT
Press the ◄ or ENTER button to finish the OSD menu.
55
PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
BRIGHTNESS
CONTRAST
Description
Using the ◄/► buttons adjusts the brightness.
Dark ó Light
Using the ◄/► buttons adjusts the contrast.
Weak ó Strong
COLOR
Using the ◄/► buttons adjusts the strength of whole color.
Weak ó Strong
• This item can be selected only for a video and component video
signal.
• For HDMITM, MHL, and HDBaseTTM signals, this item can also be
selected if either (1) or (2) applies.
(1) DIGITAL FORMAT item in the INPUT menu for selected port is
set to VIDEO.
(2) DIGITAL FORMAT item in the INPUT menu for selected port is
set to AUTO, and the projector recognizes that it receives video
signals.
TINT
Using the ◄/► buttons adjusts the tint.
Reddish ó Greenish
• This item can be selected only for a video and component video
signal.
• For HDMITM, MHL, and HDBaseTTM signals, this item can also be
selected if either (1) or (2) applies.
(1) DIGITAL FORMAT item in the INPUT menu for selected port is
set to VIDEO.
(2) DIGITAL FORMAT item in the INPUT menu for selected port is
set to AUTO, and the projector recognizes that it receives video
signals.
SHARPNESS
Using the ◄/► buttons adjusts the sharpness.
Weak ó Strong
• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.
(continued on next page)
56
PICTURE menu
Item
Description
Using the ▲/▼ cursor buttons changes the active iris control mode.
PRESENTATION ó THEATER ó OFF
ACTIVE IRIS
PRESENTATION : The active iris displays the best presentation
image for both bright and dark scenes.
THEATER : The active iris displays the best theater image for
both bright and dark scenes.
OFF : The active iris is always open.
• The screen may flicker when the PRESENTATION or THEATER
modes are selected. If this occurs select OFF.
Selecting this item displays the PICTURE
QUALITY menu.
Select an item using the ▲/▼ buttons,
and press the ► button or the ENTER
button on the remote control to execute
the item.
PICTURE
QUALITY
PICTURE MODE
STANDARD ó NATURAL ó CINEMA ó DYNAMIC


USER-3
BOARD(BLACK)


USER-2
BOARD(GREEN)


USER-1 ó DICOM SIM. ó DAYTIME ó WHITEBOARD
After selecting USER-1 / USER-2 / USER-3, the following features
are adjustable.
Gamma, Color Temp
GAMMA
This feature is only available when USER-1 / USER-2 / USER-3 is
selected.
Using the ▲/▼ buttons switches the gamma mode.
DEFAULT-1 ó CUSTOM-1 ó DEFAULT-2 ó CUSTOM-2


CUSTOM-8
DEFAULT-3


DEFAULT-8
CUSTOM-3


CUSTOM-7
DEFAULT-4


DEFAULT-7

CUSTOM-4

CUSTOM-6 ó DEFAULT-6 ó CUSTOM-5 ó DEFAULT-5
(continued on next page)
57
PICTURE menu
Item
Description
GAMMA (continued)
Selecting a mode whose name includes CUSTOM and then
pressing the ► button or the ENTER button displays
a dialog to aid you in adjusting the mode. This function is useful
when you want to change the brightness of particular tones.
Choose an item using the ◄/► buttons, and adjust the level using
the ▲/▼ buttons.
• Lines or other noise might appear on the screen when this function
is operated, but it is not a malfunction.
COLOR TEMP
This feature is only available when USER-1 / USER-2 / USER-3 is
selected.
Using the ▲/▼ buttons switches the color temperature mode.
HIGH ó CUSTOM-1 ó MID-1 ó CUSTOM-2
PICTURE


QUALITY
CUSTOM-7
MID-2
(continued)


Hi-BRIGHT-3
CUSTOM-3


CUSTOM-6
LOW


Hi-BRIGHT-2 ó CUSTOM-5 ó Hi-BRIGHT-1 ó CUSTOM-4
Selecting a mode whose name includes CUSTOM and then pressing
the ► button or the ENTER button displays a dialog to aid you in
adjusting the OFFSET and GAIN of the selected mode.
OFFSET adjustments change the color intensity on the whole tones.
GAIN adjustments mainly affect color intensity on the brighter tones.
Choose an item using the ◄/► buttons, and adjust the level using
the ▲/▼ buttons.
• Lines or other noise might appear on the screen when this function
is operated, but it is not a malfunction.
(continued on next page)
58
PICTURE menu
Item
PICTURE
QUALITY
(continued)
Description
ACCENTUALIZER
ACCENTUALIZER is a function to improve the legibility.
Using the ◄/► buttons adjusts the sharpness.
Weak ó Strong
• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.
• This function may not work properly when IMAGE OPTIMIZER is
enabled.
HDCR
A function to show a clear picture in a bright room.
Using the◄/► buttons adjusts the contrast.
• This function may not work properly when IMAGE OPTIMIZER is
enabled.
This projector has 4 memories for adjustment data (for all the items
of the PICTURE menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or
ENTER button performs each function.
LOAD-1 ó LOAD-2 ó LOAD-3 ó LOAD-4
SAVE-4 ó SAVE-3 ó SAVE-2 ó SAVE-1
MY MEMORY
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked
in the number included in the function’s name, and adjusts the
picture automatically depending on the data.
• The LOAD functions whose linked memory has no data are
skipped.
• Remember that the current adjusted condition will be lost by
loading data. If you want to keep the current adjustment, please
save it before performing a LOAD function.
• There may be some noise and the screen may flicker for a
moment when loading data. This is not malfunction.
• You can perform the LOAD function using MY BUTTON. Please
see MY BUTTON item in OPTION menu (84).
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into
the memory linked in the number included in the function’s name.
• Remember that the current data being stored of a memory will be
lost by saving new data into the memory.
59
IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table for selected port.
Item
Description
Using the ▲/▼ buttons switches the mode for aspect ratio.
ASPECT
For a computer signal
8963:
NORMAL ó 4:3 ó 16:9 ó 16:10 ó ZOOM
8961WU, 8962WU, 8960W:
NORMAL ó 4:3 ó 16:9 ó 16:10 ó ZOOM ó NATIVE
For HDMITM, HDBaseT™, and MHL signals
8963:
NORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9 ó ZOOM
8961WU, 8962WU, 8960W:
NORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9 ó ZOOM ó NATIVE
For a video signal
8963:
4:3 ó 16:9 ó 14:9 ó ZOOM
8961WU, 8962WU, 8960W:
4:3 ó 16:9 ó 16:10 ó 14:9 ó ZOOM ó NATIVE
For an input signal from the LAN port, or if there is no signal
8963: 4:3 (fixed)
8961WU, 8962WU, 8960W: 16:10 (fixed)
• The NORMAL mode keeps the original aspect ratio of the signal.
(continued on next page)
60
IMAGE menu
Item
Description
OVER SCAN
Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnifies picture) ó Large (It reduces picture)
• This item can be selected for a video signal.
• For HDMITM, MHL and HDBaseTTM signals, this item can also be
selected if either (1) or (2) applies.
(1) DIGITAL FORMAT item in the INPUT menu for selected port is
set to VIDEO.
(2) DIGITAL FORMAT item in the INPUT menu for selected port is
set to AUTO, and the projector recognizes that it receives video
signals.
V POSITION
Using the ◄/► buttons adjusts the vertical position.
Down ó Up
• Over-adjusting the vertical position may cause noise to appear on
the screen. If this occurs, please reset the vertical position to the
default setting. Pressing the RESET button when the V POSITION
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal, the range of
this adjustment depends on OVER SCAN (above) setting. It is not
possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the LAN, HDMI 1 /
MHL, HDMI 2 or HDBaseT port.
H POSITION
Using the ◄/► buttons adjusts the horizontal position.
Right ó Left
• Over-adjusting the horizontal position may cause noise to appear on
the screen. If this occurs, please reset the horizontal position to the
default setting. Pressing the RESET button when the H POSITION is
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal, the range of
this adjustment depends on OVER SCAN (above) setting. It is not
possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the LAN, HDMI 1 /
MHL, HDMI 2 or HDBaseT port.
(continued on next page)
61
IMAGE menu
Item
Description
H PHASE
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right ó Left
• This item can be selected only for a computer signal or a
component video signal.
• This function is unavailable for a signal from the LAN, HDMI 1 /
MHL, HDMI 2 or HDBaseT port.
H SIZE
Using the ◄/► buttons adjusts the horizontal size.
Small ó Large
• This item can be selected only for a computer signal.
• This function is unavailable for a signal from the LAN, VIDEO,
HDMI 1 / MHL, HDMI 2 or HDBaseT port.
• When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
by pressing the RESET button on the remote control during this
operation.
• Images might appear degraded when this function is operated, but
it is not a malfunction.
AUTO ADJUST
EXECUTE
Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal
phase will be automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal
The video format best suited for the respective input signal will
be selected automatically. This function is available only when
the AUTO is selected for the VIDEO FORMAT item in the INPUT
menu (64). The vertical position and horizontal position will be
automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds.
Also please note that it may not function correctly with some input.
• When this function is performed for a video signal, a certain extra
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black
frame may be displayed on the edge of the screen, depending on
the computer model.
• The items adjusted by this function may vary when the FINE or
DISABLE is selected for the AUTO ADJUST item of the SERVICE
item in the OPTION menu (88).
62
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó OFF
PROGRESSIVE
• This function works only for a video signal, component video signal
(of 480i@60 or 576i@50 or 1080i@50/60), an HDMITM signal
(of 480i@60 or 576i@50 or 1080i@50/60), an MHL signal (of 480i@60
or 576i@50 or 1080i@50/60) and HDBaseTTM signal (of 480i@60 or
576i@50 or 1080i@50/60).
• When TV or FILM is selected, the screen image will be sharp.
FILM adapts to the 2-3 Pull-Down conversion system. But these
may cause a certain defect (for example, jagged line) of the picture
for a quick moving object. In such a case, please select OFF, even
though the screen image may lose sharpness.
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW
VIDEO NR
• This function works only for a video signal, component video signal
(of 480i@60 or 576i@50 or 1080i@50/60), an HDMITM signal
(of 480i@60 or 576i@50 or 1080i@50/60), an MHL signal (of 480i@60
or 576i@50 or 1080i@50/60) and HDBaseTTM signal (of 480i@60 or
576i@50 or 1080i@50/60).
Using the ▲/▼ buttons switches the mode for color space.
AUTO ó RGB ó SMPTE240 ó REC709 ó REC601
COLOR SPACE
• This item can be selected only for a computer signal (except for
signals from the LAN port).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a
case, it might be good to select a suitable mode except AUTO.
(continued on next page)
63
INPUT menu
Item
Description
VIDEO FORMAT
The video format for VIDEO port can be set.
Using the ◄/► buttons
switches the mode for video
format.
AUTO ó NTSC ó PAL ó SECAM
N-PAL ó M-PAL ó NTSC4.43
• This item is performed only for a video signal from the VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the
picture becomes unstable (e.g. an irregular picture, lack of color),
please select the mode according to the input signal.
The digital format of HDMITM/MHL input signals from the HDMI 1/
MHL, HDMI2 and HDBaseTTM ports can be set.
8962WU/8960W
C
8961WU/8963
CP-X5550
DIGITAL FORMAT (1) Use the ▲/▼ buttons to select the port to be set.
(2) Use the ◄/►buttons to select the digital format.
AUTO ó VIDEO ó COMPUTER
AUTO: automatically sets the optimum mode.
VIDEO: sets the suitable mode for DVD signals.
COMPUTER: sets the suitable mode for computer signals.
• When the COMPUTER is selected, the function OVER SCAN
(IMAGE menu) is unavailable.
(continued on next page)
64
INPUT menu
Item
Description
TM
The digital range of HDMI /MHL input signals from the HDMI 1/
MHL, HDMI 2 and HDBaseTTM ports can be set.
8962WU/8960W
CP-X5555
DIGITAL RANGE
8961WU/8963
CP-X5550
(1) Use the ▲/▼ buttons to select the port to be set.
(2) Use the ◄/►buttons to select the digital range.
AUTO ó NORMAL ó ENHANCED
AUTO: a
utomatically sets the optimum mode.
NORMAL: sets the suitable mode for DVD signals. (16-235)
ENHANCED: sets the suitable mode for computer signals. (0-255)
• If the contrast of the screen image is too strong or too weak, try
finding a more suitable mode.
COMPUTER IN
The computer input signal type for COMPUTER IN port can be set.
Use the ◄/► buttons to select the
computer input signal type.
AUTO ó SYNC ON G OFF
• Selecting the AUTO mode allows
you to input a sync on G signal or component video signal from the
port.
• In the AUTO mode, the picture may be distorted with certain
input signals. In such a case, remove the signal connector so that
no signal is received and select the SYNC ON G OFF, and then
reconnect the signal.
Set the frame lock function on/off for each port.
8962WU/8960W
CP-X5555
FRAME LOCK
8961WU/8963
CP-X5550
(1) Use the ▲/▼ buttons to select the input ports.
(2) Use the ◄/► buttons to turn the frame lock function on/off .
ON ó OFF
• This item can be performed only on a signal with a vertical
frequency of 49 to 51Hz, 59 to 61 Hz.
• When ON is selected, moving pictures are displayed more
smoothly.
(continued on next page)
65
INPUT menu
Item
Description
RESOLUTION
The resolution for the COMPUTER IN input signal can be set on this
projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼
buttons and press the ► button.
The RESOLUTION menu will be
displayed.
(2) In the RESOLUTION menu select the
resolution you wish to display using
the ▲/▼ buttons.
Selecting AUTO will set a resolution
appropriate to the input signal.
(3) Pressing the ► or ENTER button when
STANDARD
selecting a STANDARD resolution will
↓
automatically adjust the horizontal and
vertical positions, clock phase and
horizontal size.
The INPUT_INFORMATION dialog will be
displayed.
(4) To set a custom resolution use the ▲/▼ buttons to select
the CUSTOM and the RESOLUTION_CUSTOM box will be
displayed.
CUSTOM
Set the (HORZ) and (VERT)
↓
resolutions using the ▲/▼/◄/►
buttons.
This function may not support all
resolutions.
(5) Move the cursor to OK on screen and press the ► or ENTER
button. The message "ARE YOU SURE YOU WISH TO CHANGE
RESOLUTION?" appears. To save the setting, press the ►
button.
The horizontal and vertical positions, clock phase and horizontal
size will be automatically adjusted.
The INPUT_INFORMATION dialog
will be displayed.
(6) To revert back to the previous resolution without saving changes,
move the cursor to CANCEL on screen and press the ◄ or
ENTER button.
The screen will then return to the RESOLUTION menu displaying
the previous resolution.
• For some pictures, this function may not work well.
(continued on next page)
66
INPUT menu
Item
Description
PinP POSITION
Using ▲/▼ buttons on the remote control changes the position of
sub area in PinP mode (50).
PbyP / PinP
SETUP
PbyP / PinP FRAME LOCK
Select the screen that enables FRAME LOCK function when using
PbyP or PinP.
LEFT / PRIMARY: Enables FRAME LOCK function for input on left
screen of PbyP or on primary area of PinP.
RIGHT / SECONDARY: Enables FRAME LOCK function for input on
right screen of PbyP or on secondary area of PinP.
MHL STANDBY
PWR.
Using the ▲/▼ buttons switches the MHL STANDBY PWR. ON/
OFF.
ON ó OFF
• When the STANDBY MODE is set to SAVING, the MHL STANDBY
PWR. menu cannot be operated and MHL power feeding is
unavailable with standby mode (72).
• When the MHL STANDBY PWR. is set to ON, there may be some
noise with standby mode. This is not malfunction.
67
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
KEYSTONE
Selecting this item displays the KEYSTONE dialog.
For details, see KEYSTONE in Correcting the distortion(38).
• When the zoom adjustment is set to the TELE (telephoto focus),
this function may be excessive. This function should be used when
the zoom adjustment is set to the full WIDE (wide-angle focus)
whenever possible.
• When the horizontal lens shift is not set to the center, this function
may not work well.
• This function is unavailable when the screen is activated by
PERFECT FIT (39), and WARPING (40).
GEOMETRY
CORRECTION
PERFECT FIT
Selecting this item displays the PERFECT FIT dialog. For details,
see PERFECT FIT in Correcting the distortion (39).
• This function is unavailable when the screen is activated by
KEYSTONE (38), and WARPING (40).
WARPING
Selecting this item displays the WARPING dialog. For details, see
Application Manual of this feature.
• This function is unavailable when the screen is activated by
KEYSTONE (38) and PERFECT FIT (39).
EDGE BLENDING
Selecting this item displays the EDGE BLENDING dialog. For
details, see EDGE BLENDING feature (41 ~ 44).
(continued on next page)
68
SETUP menu
Item
GEOMETRY
CORRECTION
(continued)
LAMP & FILTER
Description
PATTERN
Select PATTERN with ▲/▼ buttons.
Displayed pattern [Off/1/2/3/4/5/6] can be switched with ◄/► buttons.
PATTERN 1: Frame
PATTERN 2: Red Grid
PATTERN 3: Green Grid
PATTERN 4: Blue Grid
PATTERN 5: Vertical 9 steps
PATTERN 6: Horizontal 9 steps
OFF: D
isplays the input signal.
Selecting this item displays the LAMP
& FILTER menu.
Select an item using the ▲/▼ buttons,
and press the ► button or the ENTER
button on the remote control to
execute the item.
ECO MODE
Using the ▲/▼ buttons switches the Eco mode.
NORMAL ó ECO
• When the item other than NORMAL is selected, acoustic noise and
screen brightness are reduced.
LAMP TIME
The lamp time is the usage time of the lamp, counted after the last
resetting. It is shown in the LAMP & FILTER menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the lamp time, select the OK using the ► button.
CANCEL  OK
• For the lamp replacement, see the section Replacing the lamp
(103).
• The IMAGE OPTIMIZER function does not work properly unless
LAMP TIME is initialized when replacing a lamp.
(continued on next page)
69
SETUP menu
Item
Description
FILTER TIME
The filter time is the usage time of the air filter, counted after the last
resetting. It is shown in the LAMP & FILTER menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the filter time, select the OK using the ► button.
CANCEL  OK
• Please reset the filter time only when you have cleaned or
replaced the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section Cleaning and replacing
the air filter (105).
LAMP & FILTER
(continued)
IMAGE
OPTIMIZER
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message
when to replace the filter unit
1000h ó 2000h ó 5000h ó 10000h ó 15000h ó 20000h ó 25000h ó 30000h ó OFF
After choosing an item except OFF, the message “REMINDER ***
HRS PASSED ....” will appear after the timer reaches the interval
time set by this feature.
When the OFF is chosen, the message will not appear. Utilize this
feature to keep the air filter clean, setting the suitable time according
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is
no message. If the air filter becomes to be blocked by dust or
other matter, the internal temperature will rise, which could cause
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector
and the condition of the filter unit.
When this function is enabled, automatic image correction is
performed to maintain visibility in accordance with lamp deterioration.
• This function may not work properly when HDCR/ACCENTUALIZER
is set to other than 0.
• This function does not work properly unless LAMP TIME is initialized
when replacing a lamp.
(continued on next page)
70
SETUP menu
Item
Description
PICTURE
POSITION
Using the ▲/▼/◄/► cursor buttons selects the desirable picture
position.
The PICTURE POSITION is not changed if any of the following
cases apply.
・There is no non-display area (black display or background display)
or it is not displayed on the screen.
• One of the following messages is displayed on the screen:
"NO INPUT IS DETECTED"
"SYNC IS OUT OF RANGE"
"INVALID SCAN FREQ."
• The BLANK or TEMPLATE function is selected.
Pressing the ►button displays the dialog for changing the
INSTALLATION setting.
FRONT / DESKTOP
REAR / DESKTOP
INSTALLATION

REAR / CEILING


FRONT / CEILING
Use the ▲/▼ buttons to select the desired setting on the
INSTALLATION dialog, and press the ENTER button of the remote
control or the INPUT button of the projector to execute.
If TRANSITION DETECTOR is ON and the INSTALLATION status
is changed, the TRANSITION DETECTOR ON alarm (99) will be
displayed when the projector is restarted.
(continued on next page)
71
SETUP menu
Item
Description
STANDBY MODE
Using ▲/▼ buttons switches the standby mode setting between
NORMAL and SAVING.
NORMAL ó SAVING
• When SAVING is selected, the RS-232C communication control
except to turn the projector on and the network function are disabled
while the projector is in the standby mode. If the COMMUNICATION
TYPE in the COMMUNICATION menu is set to NETWORK
BRIDGE, all of the RS-232C commands are disabled (90).
• When SAVING is selected, STANDBY OUTPUT is invalid.
• When SAVING is selected, the HDMI Link and HDBaseT™
functions are disabled while the projector is in the standby mode.
• This function is available only when OFF is selected for STACK
MODE. (OPTION menu > SERVICE > COMMUNICATION >
STACK).
• When SAVING is selected, SCHEDULE function (Ex. POWERON) at STANDBY MODE will not be operated.
• When SAVING is selected, the MHL STANDBY PWR. menu
cannot be operated and MHL power feeding is unavailable with
standby mode(67).
COLOR
UNIFORMITY
Selects image level and region that are desired to be corrected, and
adjusts Color Balance.
Divides the screen into 9 regions and adjusts gain of R/G/B of each
region.
(continued on next page)
72
SETUP menu
Item
Description
Using the ▲/▼ buttons turns on/off the message function.
NORMAL ó SILENT  INHIBIT
OSD MESSAGE
■SILENT : The following message functions do not work.
“AUTO IN PROGRESS” while automatically adjusting.
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“Searching….” while searching for the input.
“Detecting….” while an input signal is detected.
The indication of the input signal displayed by changing.
The indication of the aspect ratio displayed by changing.
The indication of the PICTURE MODE displayed by changing.
The indication of the ACTIVE IRIS displayed by changing.
The indication of the MY MEMORY displayed by changing.
The indication of “FREEZE” and “II” while freezing the screen by
pressing the FREEZE button.
The indication of the TEMPLATE displayed by changing.
The indication of the ECO MODE displayed by changing.
■INHIBIT : All message functions do not work.
The only buttons will function are as below.
STANDBY, ON
•To change this function, follow the steps below.
1. Press the OSD MSG button on the remote control for 3 sec.
2. The INHIBIT OSD will be displayed.
While this OSD is displayed, press the OSD MSG button again
on the remote control.
3. Toggle and change the function.
NORMAL ó SILENT  INHIBIT
(continued on next page)
73
SETUP menu
Item
HDMI OUTPUT
STANDBY
OUTPUT
Description
To select the image output on the HDMI OUT in the normal operation.
AUDIO OUT
To select the sound output in the standby mode.
MONITOR OUT
To select the image output on the MONITOR OUT in the standby mode.
HDMI OUT
To select the image output on the HDMI OUT in the standby mode.
• When the STANDBY MODE is set to SAVING, the STANDBY
OUTPUT menu can not be operated.
74
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below
can be performed. Select an item using the ▲/▼ cursor
buttons, and press the ► cursor button or the ENTER
button to execute the item. Then perform it according to
the following table.
Item
Description
VOLUME
Using the ◄/► buttons adjusts the volume of the audio output.
Low ó High
SPEAKER
Using the ▲/▼ buttons turns on/off the built-in speaker.
ON ó OFF
When OFF is selected, the built-in speaker does not work.
While the image signal from the input port chosen in step (1) is
projected, the audio signal from the input port selected in step
(2) is output to both the AUDIO OUT port and built-in speaker of
this projector. However, the built-in speaker does not work when
SPEAKER is set to OFF.
8962WU/8960W
CP-X5555
AUDIO SOURCE
8961WU/8963
CP-X5550
(1) Choose a picture input port using the ▲/▼ buttons.
(2) Select an audio input port or the mute icon using the ◄/► buttons.
The icons indicate the following;
No.2: AUDIO IN2 port
No.1: AUDIO IN1 port
No.3: HDMI 1 / MHL port No.4: HDMI 2 port
No.5: HDBaseT port
No.6: LAN port
: mutes the sound
• Audio input from port Nos.3 to 6 can only be selected by each of
the picture input ports and AUDIO OUT STANDBY.
• C.C. (Closed Caption) is automatically activated when is selected
and an input signal containing C.C. is received. This function is
available only when the signal is NTSC for VIDEO or COMPUTER
IN, and when AUTO is selected for DISPLAY in the C.C. menu under
the SCREEN menu (81).
• For the setting of AUDIO OUT, refer to AUDIO OUT of STANDBY
OUTPUT in the SETUP menu.
75
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
LANGUAGE
Description
Using the ▲/▼/◄/► buttons switches the OSD (On Screen
Display) language.
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL
(shown in the LANGUAGE dialog)
Press the ENTER or
MENU POSITION
button to save the language setting.
Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the MENU button on the remote control
or keep no operation for about 10 seconds.
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
(46). It is displayed by pressing the BLANK button on the remote
control.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK
BLANK
MyScreen : S
creen can be registered by the MyScreen item (78).
ORIGINAL : S
creen preset as the standard screen.
BLUE, WHITE, BLACK : P
lain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL
screen will change to the AUTO BLANK screen after several
minutes.
(continued on next page)
76
SCREEN menu
Item
Description
Using the ▲/▼ buttons switches the mode for the AUTO BLANK
screen.
BLUE ó WHITE ó BLACK
AUTO BLANK
• To avoid remaining as an afterimage, displayed image will change
to the designated blank color screen by AUTO BLANK after several
minutes at the following conditions.
- When MyScreen or ORIGINAL is displayed as BLANK screen.
- When start-up screen is displayed.
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an
unsuitable signal is detected.
MyScreen ó ORIGINAL ó OFF
START UP
MyScreen : S
creen can be registered by the MyScreen item (78).
ORIGINAL : S
creen preset as the standard screen.
lain black screen.
OFF : P
• To avoid remaining as an afterimage, the START UP screen will
change to the AUTO BLANK screen after several minutes.
• When the ON is selected to the MyScreen PASSWORD item in
the SECURITY menu (97), the START UP is fixed to MyScreen.
(continued on next page)
77
SCREEN menu
Item
Description
MyScreen
This item allows you to capture an image for use as a MyScreen
image which can be used as the BLANK screen and START UP
screen. Display the image you want to capture before executing the
following procedure.
(1) Selecting this item displays a dialog
titled “MyScreen”. It will ask you if
you start capturing an image from
the current screen.
Please wait for the target image to be displayed, and press the
ENTER or
button when the image is displayed. The image
will freeze and the frame for capturing will appear.
To stop performing, press the RESET button on the remote
control.
(2) Using the ▲/▼/◄/► buttons adjusts
the frame position.
Please move the frame to the position
of the image which you want to use. The
frame may not be able to be moved for
some input signals.
To start registration, press the ENTER
button on the remote control or INPUT
button on the control panel.
To restore the screen and return to the previous dialog, press the
RESET button on the remote control or press the ◄ and INPUT
buttons at the same time on the control panel.
Registration may take several minutes.
When the registration is completed, the registered screen and
the following message is displayed for several seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed:
“A capturing error has occurred. Please try again.”
• This function cannot be selected when the ON is selected to the
MyScreen Lock item (79).
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu (97).
• This function is unavailable for a signal from the LAN, HDMI 1/
MHL, HDMI 2 or HDBaseT port.
(continued on next page)
78
SCREEN menu
Item
MyScreen Lock
Description
Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON ó OFF
When the ON is selected, the item MyScreen is locked. Use this
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu (97).
Each input port for this projector can have a name applied to it.
(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE
NAME and press the ► or ENTER button.
The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE NAME menu to select
the port to be named and press the ► button. The SOURCE
NAME dialog will be displayed.
Right side of the menu is blank until a name is specified.
8962WU/8960W
CP-X5555
SOURCE NAME
8961WU/8963
CP-X5550
(3) Select an icon you would like to assign to
the port in the SOURCE NAME dialog.
The name assigned to the port will also be
automatically switched according to your
icon selection. Press the ENTER or
button to determine your icon selection.
(4) Select a number you would like to assign
to the port along with the icon. You can
select the number either from blank (no
number assigned), 1, 2, 3, or 4.
Then press the ENTER or
button.
(5) If you would like to modify the name
assigned to the port, select CUSTOM NAME and press the
button.
ENTER or
8962WU/8960W
CP-X5555
8961WU/8963
CP-X5550
(continued on next page)
79
SCREEN menu
Item
Description
SOURCE NAME
(continued)
(6) The current name will be displayed
on the first line. Use the ▲/▼/◄/►
buttons and the ENTER or
button to
select and enter characters. To erase 1
character at one time, press the RESET
button or press the ◄ and
button
at the same time. Also if you move the
cursor to DELETE or CLEAR ALL on
screen and press the ENTER or
button, 1 character or all characters will
be erased. The name can be a maximum
of 16 characters.
(7) To change an already inserted character,
press the ▲ button to move the cursor to
the first line, and use the ◄/► buttons to
move the cursor on the character to be
changed.
After pressing the ENTER or
button, the character is selected.
Then, follow the same procedure as described at the item (6)
above.
(8) To finish entering text, move the cursor to the OK on screen
button. To revert to the previous
and press the ►, ENTER or
name without saving changes, move the cursor to the CANCEL
button.
on screen and press the ◄, ENTER or
TEMPLATE
Using the ▲/▼ cursor buttons switches the mode for the template
screen.
Press the ► cursor (or the ENTER) button to display the selected
template, and press the ◄ cursor button to close the displayed
screen.
The last selected template is displayed when the MY BUTTON
allocated to the TEMPLATE function is pressed (84).
TEST PATTERN ó DOT-LINE1 ó DOT-LINE2 ó DOT-LINE3


STACK ó MAP2 ó MAP1 ó CIRCLE2 ó CIRCLE1 ó DOT-LINE4
You can turn a map upside down and scroll it horizontally when
MAP1 or MAP2 is selected. To invert or scroll the map, display
the guidance by pressing the RESET button on the remote three
seconds or more when MAP1 or MAP2 appears.
(continued on next page)
80
SCREEN menu
Item
Description
The C.C. is the function that displays a
transcript or dialog of the audio portion of
a video, files or other presentation or other
relevant sounds. It is required to have NTSC
format video or 480i@60 format component
video source supporting C.C. feature to
utilize this function.
It may not work properly, depending on equipment or signal source.
In this case, please turn off the Closed Caption.
DISPLAY
Select Closed Caption DISPLAY setting from following options using
▲/▼ buttons.
AUTO ó ON ó OFF
C.C.
(Closed Caption)
AUTO : C
losed Caption automatically appears when the input signal
(C.C. compatible) from the port with the mute icon set at
AUDIO SOURCE is selected.
ON : Closed Caption is on.
OFF : Closed Caption is off.
• The caption is not displayed when the OSD menu is active.
• The Closed Caption is the function to display the dialogue,
narration, and / or sound effects of a television program or other
video sources. The Closed Caption availability is depending upon
broadcaster and/or content.
MODE
Select Closed Caption MODE setting from following options using
▲/▼ buttons.
CAPTIONS ó TEXT
CAPTIONS : Display Closed Caption.
isplay Text data, which is for additional information such as
TEXT : D
news reports or a TV program guide. The information covers
the entire screen. Not all of the C.C. program has Text
information.
CHANNEL
Select Closed Caption CHANNEL from following options using ▲/▼
buttons.
1ó2ó3ó4
1: Channel 1, primary channel / language
2: Channel 2
3: Channel 3
4: Channel 4
The channel data may vary, depending on the content. Some
channel might be used for secondary language or empty.
81
OPTION menu
OPTION menu
From the OPTION menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
The ports can be set to be ignored in searching by the AUTO
SEARCH function (below) or in selecting by buttons on the control
panel.
8962WU/8960W
CP-X5555
8961WU/8963
CP-X5550
SOURCE SKIP
(1) Choose a picture input port using the ▲/▼ buttons.
(2) Using the ◄/►buttons turns on/off the SOURCE SKIP function.
NORMAL  SKIP
The port that is set to SKIP will be ignored.
• It is not possible to set SKIP to all ports at the same time.
• This setting is not valid when in the PbyP /PinP mode (47).
AUTO SEARCH
Using the ▲/▼ buttons turns on/off the automatic signal search
function.
ON  OFF
When the ON is selected, detecting no signal automatically cycles
through input ports in the following order. The search is started from
the current port. Then when an input is found, the projector will stop
searching and display the image.
LAN  COMPUTER IN  HDMI 1 / MHL


VIDEO ï HDBaseT * ï HDMI 2
* 8962WU/8960W only
(continued on next page)
82
OPTION menu
Item
Description
DIRECT POWER
ON
Using the ▲/▼ buttons turns on/off the DIRECT POWER ON
function.
ON  OFF
When set to the ON, the lamp in projector will be automatically turned
on without the usual procedure (30), only when the projector is
supplied with the power after the power was cut while the lamp was on.
• This function does not work as long as the power has been
supplied to the projector while the lamp is off.
• After turning the lamp on by the DIRECT POWER ON function,
if neither input nor operation is detected for about 30 minutes, the
projector is turned off, even though the AUTO POWER OFF function
(below) is disabled.
Using the ▲/▼ buttons adjusts the time to count down to
automatically turn the projector off.
Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)
AUTO POWER
OFF
SHADE TIMER
When the time is set to 0, the projector is not turned off
automatically.
When the time is set to 1 to 99, and when the passed time with
no-signal or an unsuitable signal reaches at the set time, the
projector lamp will be turned off.
If one of the projector's buttons or the remote control buttons
is pressed or one of the commands (except get commands) is
transmitted to the CONTROL port during the corresponding time,
projector will not be turned off.
Please refer to the section Turning off the power (31).
Using the ▲/▼ buttons sets the time from closing the lens shade to
automatically turning the projector off.
1h ó 3h ó 6h
• The shade will open automatically when turning the projector on
again.
(continued on next page)
83
OPTION menu
Item
Description
MY BUTTON
This item is to assign one of the following functions to MY BUTTON
(1 to 2) on the remote control (7).
(1)Use the ▲/▼ buttons on the MY BUTTON menu to select a
button from MY BUTTON - 1 to 4 and press the ► or ENTER
button to display the MY BUTTON setup dialog.
(2)Then using the ▲/▼/◄/► buttons sets one of the following
button to
functions to the chosen button. Press the ENTER or
save the setting.
MY IMAGE: Displays the MY IMAGE menu.(5. My Image
Function in the Network Guide)
MESSENGER: Turns the messenger text displayed on the screen
on/off (6. Messenger Function in the Network Guide).
When there is no transferred text data to display, the message
”NO MESSENGER DATA" appears.
SHADE: Turns the lens shade closed and opened.
PbyP / PinP SWAP: Swaps the picture on the right with one on
the left in the PbyP mode. Swaps the primary picture and the
secondary picture in the PinP mode. (50)
PinP POSITION: Toggles the PinP position.
ACCENTUALIZER: Turns on/off the ACCENTUALIZER dialog (59).
HDCR: Turns on/off the HDCR dialog (59).
INFORMATION: Displays SYSTEM_INFORMATION → INPUT_
INFORMATION (94) → NETWORK_INFORMATION.
MY MEMORY: Loads one of adjustment data stored (59).
When more than one data are saved, the adjustment
changes every time the MY BUTTON is pressed.
When no data is saved in memory, the
dialog "No saved data" appears.
When the current adjustment is not
saved to memory, the dialog as shown in
the right appears.
If you want to keep the current adjustment, please press
the ► button to exit. Otherwise loading a data will overwrite the
current adjusted condition.
ACTIVE IRIS: Changes the active iris mode (57).
PICTURE MODE: Changes the PICTURE MODE (57).
FILTER RESET: Displays the filter time reset confirmation dialogue
(70).
TEMPLATE: Makes the template pattern selected to the TEMPLATE
item (80) appear or disappear.
RESOLUTION: Turns on/off the RESOLUTION dialog (66).
ECO MODE: Changes the ECO MODE dialog (69).
(continued on next page)
84
OPTION menu
Item
Description
■ How to setup the item
1. Use the ▲/▼/◄/► cursor buttons to select or adjust.
2. Select OK to finish the settings.
NOTE Please refer to the actual on-screen display(OSD) for
appropriate operation.
Item
DATE & TIME
Description
Set the DATE(Year/Month/Date) and Time(24hour scale).
SPECIFIC DATE
Set specific date from 1 to 10.
PROGRAM EDIT
The TIME and EVENT for Program 1 to 16
can be edited.
■ How to activate (DATE AND TIME / SPECIFIC DATE)
Place a check mark in the box.
SCHEDULE
Check mark
in the box
Date and first
setup info could
be seen with the
check mark.
1/2 page (Set the DATE(Year/Month/Date) and Time(24-hour scale).)
(continued on next page)
85
OPTION menu
Item
Description
Check mark
in the box
Date and first
setup info could
be seen with the
check mark.
2/2 page (Set specific date from 1 to 10.)
SCHEDULE
(continued)
■ PROGRAM EDIT
The TIME and EVENT for Program 1 to 16 can be edited.
• RETURN
Select this to go back
to the top menu of the
SCHEDULE.
• SELECT
Select from PROGRAM-01
to 16 to edit.
Each PROGRAM can be
setup up to 20 settings.
• COPY TO
The selected program
(with the settings of TIME
and EVENT) can be
copied to other program.
• APPLY
Select this to apply and
save all adjustments and
settings.
(continued on next page)
86
OPTION menu
Item
Description
■ How to edit the selected PROGRAM
1. Select from 1 to 20 events.
Use the ▲/▼ cursor buttons to select.
Press ► cursor button to set the TIME and EVENT.
2. Use the ◄/► cursor
buttons to select.
3. Use the ▲/▼ cursor
buttons to adjust.
SCHEDULE
(continued)
EVENT can be selected as listed below.
◦ POWER − ON, STANDBY
◦ INPUT SOURCE − "input source" channel
◦ MY IMAGE − IMAGE-1 to 4, IMAGE OFF
◦ MESSENGER − TEXT-1 to 12, TEXT OFF
◦ ECO MODE − N
ORMAL, ECO
◦ BLANK − ON, OFF
4. Press ► cursor button to finish the settings.
5. Select APPLY to save the settings.
NOTE • Please refer to the actual on-screen display(OSD) for
appropriate operation.
• When the STANDBY MODE is set to SAVING, SCHEDULE
function (Ex:POWER-ON) at STANBY MODE will not be operated.
(continued on next page)
87
OPTION menu
Item
Description
Selecting this item displays the SERVICE
menu.
Select an item using the ▲/▼ buttons,
and press the ► button or the ENTER
button on the remote control to execute
the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling
fans. If the projector is used at an altitude of about 1600 m or higher,
select HIGH. Otherwise, select NORMAL. Note that the projector is
noisier when the HIGH is selected.
HIGH ó NORMAL
SERVICE
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the
DISABLE is selected, the automatic adjustment feature is disabled.
FINE ó FAST ó DISABLE
FINE: Finer tuning including H.SIZE adjustment.
FAST: Faster tuning, setting H.SIZE to prearranged data for the
input signal.
• Depending on conditions, such as input image, signal cable to
the projector, environment around the projector, etc., the automatic
adjustment may not work correctly. In such a case, please
choose DISABLE to disable the automatic adjustment, and make
adjustment manually.
GHOST *
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
* 8960W/8963 only
(continued on next page)
88
OPTION menu
Item
Description
KEY LOCK
(1)Use the ▲/▼ buttons to choose the operations control.
CONTROL PANEL ó REMOTE CONTROL
(2)Use the ◄/► buttons to select ON or
OFF.
ON ó OFF
Selecting ON in Step 2 locks the buttons except STANDBY/ON on
the operations control selected in Step 1.
Selecting OFF releases the locked buttons on the operations
control selected in Step 1.
• Please use this function to prevent tampering or accidental
operation.
• It's not possible to disable both options at the same time.
REMOTE RECEIV. *
Switch it using the ◄/► button.
ON ó OFF
SERVICE
(continued)
REMOTE FREQ.
(1)Use the ▲/▼ button to change the projector's remote sensor
frequency setting (4, 28).
1:NORMAL ó 2:HIGH
(2)Use the ◄/► button to change the
projector's remote sensor on or off.
ON ó OFF
If the remote control does not function correctly, disable either of
them.
• It's not possible to disable both options at the same time.
REMOTE ID
Use the ▲/▼ buttons on the REMOTE ID menu to select ID and
press the ► button.
ALL ó 1 ó 2 ó 3 ó 4
The projector is controlled by the remote control whose ID button
is set the same number as this number. When the ALL is selected,
the projector is controlled by a remote control irrespective of the ID
setting.
• Available only in optional remote control.
* 8962WU/8960W only
(continued on next page)
89
OPTION menu
Item
Description
Selecting this item displays COMMUNICATION
menu.
In this menu, you can configure the serial
communication settings of the projector using the
CONTROL port.
• Select an item using the cursor buttons ▲/▼.
Then pressing the ► button opens the submenu
for the setting item you selected. Or, pressing
the ◄ button instead of the ► button makes the
menu back to the previous one without changing
the setup. Each submenu can be operated as
described above.
• When COMMUNICATION TYPE (below) is
set to OFF, the other items except STACK in
COMMUNICATION menu are invalid.
• For the function of serial communication, refer to
the Network Guide.
SERVICE
(continued)
COMMUNICATION TYPE
COMMUNICATION Select the communication type for transmission via
the CONTROL port.
NETWORK BRIDGE (WIRELESS)

NETWORK BRIDGE (WIRED)

OFF
NETWORK BRIDGE: Select this type, if it is
required to control an external device as a
network terminal, via this projector from the
computer. Select WIRELESS or WIRED as your
network connection mode.
The CONTROL port does not accept RS-232C
commands (7. Network Bridge Function in
the Network Guide).
OFF: Select this mode to receive RS-232C
commands using the CONTROL port.
• OFF is selected as the default setting.
• When you select the NETWORK BRIDGE, check
the item, TRANSMISSION METHOD (91).
・When NETWORK BRIDGE is selected, RS-232C
menu of CONTROL TERMINAL cannot be set. The
setting of RS-232C is forcibly set to CONTROL.
(continued on next page)
90
OPTION menu
Item
Description
SERIAL SETTINGS
Select the serial communication condition for the
CONTROL port.
BAUD RATE
4800bps ó 9600bps ó 19200bps ó 38400bps
PARITY
NONE ó ODD ó EVEN
• The BAUD RATE is fixed to 19200bps and PARITY
is fixed NONE when the COMMUNICATION TYPE
is set to OFF (90).
SERVICE
(continued)
COMMUNICATION TRANSMISSION METHOD
(continued)
Select the transmission method for communication by
the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX ó FULL-DUPLEX
HALF-DUPLEX: This method lets the projector
make two way communication, but only one
direction, either transmitting or receiving data, is
allowed at a time.
FULL-DUPLEX: This method lets the projector
make two way communication, transmitting and
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of
the item RESPONSE LIMIT TIME (92).
(continued on next page)
91
OPTION menu
Item
Description
RESPONSE LIMIT TIME
Select the time period to wait for receiving
response data from other device communicating by
the NETWORK BRIDGE and the HALF-DUPLEX
through the CONTROL port.
OFF ó 1s ó 2s ó 3s
SERVICE
(continued)
OFF: Select this mode if it is not required to check
the responses from the device that the projector
sends data to. In this mode, the projector can
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the
projector waiting for response from the device
that the projector sends data to. While waiting the
response, the projector does not send out any
COMMUNICATION data from the CONTROL port.
(continued)
• This menu is available only when the NETWORK
BRIDGE is selected for the COMMUNICATION
TYPE and the HALF-DUPLEX is selected for the
TRANSMISSION METHOD (91).
• OFF is selected as the default setting.
STACK
Selecting this item displays the STACK menu.
For more information, please see Instant Stack
Guide.
• When STACK MODE is set to MAIN or SUB,
the other items in COMMUNICATION menu are
invalid.
• When STACK MODE is set to MAIN or SUB,
RS-232C menu of CONTROL TERMINAL cannot
be set. The setting of RS-232C is forcibly set to
CONTROL.
(continued on next page)
92
OPTION menu
Item
Description
WIRED NETWORK
Selects whether to use LAN or HDBaseT port.
LAN ó HDBaseT
NOTE • Only either LAN or HDBaseT port
can be used for the connection to the network.
Switch it according to the environment.
CONTROL
TERMINAL *
RS-232C
Selects whether to use CONTROL or HDBaseT
port.
CONTROL ó HDBaseT
NOTE • Only either CONTROL or HDBaseT
SERVICE
(continued)
port can be used for the RS-232C connection.
Switch it according to the environment.
Selects the device to refer to the resolution
information of HDMI output.
EXTERNAL DEVICE ⇔ PROJECTOR
・When EXTERNAL DEVICE is selected, the
HDMI OUT
resolution of the signal input to the projector and
RESOLUTION signal output from the projector may be restricted
by the maximum resolution of the connected
device such as projector or monitor.
・When PROJECTOR is selected, the image from
the device connected to HDMI OUT may not be
displayed normally.
* 8962WU/8960W only
(continued on next page)
93
OPTION menu
Item
Description
INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”.
It shows the information about the current input.
SERVICE
(continued)
• The “FRAME LOCK” message on the dialog means the frame lock
function is working.
• This item cannot be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is
displayed together with the input information in the
INPUT_INFORMATION box (101).
FACTORY RESET
Selecting OK using the ► button performs this function. By this
function, all the items in all of menus will collectively return to the
initial setting. Note that the items LAMP TIME, FILTER TIME,
LANGUAGE, AUTO BLANK, FILTER MESSAGE, STANDBY MODE,
COMMUNICATION, NETWORK and SECURITY settings are not
reset.
CANCEL  OK
94
NETWORK menu
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble on
the network. Be sure to consult with your network administrator before connecting
to an existing access point on your network.
95
SECURITY menu
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table
below can be performed.
To use SECURITY menu: User registration is required
before using the security functions.
Enter to the SECURITY menu
1. Press the ► button. The ENTER PASSWORD box will be displayed.
2. Use the ▲/▼/◄/► buttons to enter the registered password. The
factory default password is as follows.
8961WU/8962WU : 2905 8960W : 1205
8963: 2805
This password can be changed (below). Move the cursor to the
right side of the ENTER PASSWORD box and press the ► button to
display the SECURITY menu.
• It is strongly recommended the factory default password to be
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box
will be displayed again. If incorrect password is input 3 times, the
projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.
3. Items shown in the table below can be performed.
If you have forgotten your password
(1) While the ENTER PASSWORD box is displayed, press and hold the
RESET button on the remote control for about 3 seconds or press
and hold the INPUT button for 3 seconds while pressing the ►
button on the projector.
(2) The 10 digit Inquiring Code will be displayed. Contact your dealer
with the 10 digit Inquiring Code. Your password will be sent after
your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will
close. If necessary, repeat the process from (1). Item
SECURITY
PASSWORD
CHANGE
Description
(1) Use the ▲/▼ buttons on the SECURITY menu
to select SECURITY PASSWORD CHANGE
and press the ► button to display the ENTER
NEW PASSWORD box.
(2) Use the ▲/▼/◄/► buttons to enter the new password.
(3) Move the cursor to the right side of the ENTER
NEW PASSWORD box and press the ► button
to display the NEW PASSWORD AGAIN box,
enter the same password again.
(4) Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press the ►
button and the NOTE NEW PASSWORD box
will be displayed for about 30 seconds, please
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
(continued on next page)
96
SECURITY menu
Item
Description
The MyScreen PASSWORD function can be used to prohibit access to the
MyScreen function and prevent the currently registered MyScreen image
from being overwritten.
1 Turning on the MyScreen PASSWORD
MyScreen
PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select MyScreen PASSWORD and press the ►
button to display the MyScreen PASSWORD on/
off menu.
1-2 Use the ▲/▼ buttons on the MyScreen
PASSWORD on/off menu to select ON.
The ENTER NEW PASSWORD box (small)
will be displayed.
ENTER NEW PASSWORD
box (small)
1-3 Use the ▲/▼/◄/► buttons to enter the
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, enter the same
PASSWORD again.
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
the ► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
please make note of the password during
this time.
Pressing the ENTER button on the remote control or ► button on the
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD
2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
ENTER PASSWORD box
MyScreen PASSWORD on/off menu.
(large)
If an incorrect PASSWORD is input, the menu will
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
97
SECURITY menu
Item
Description
PIN LOCK is a function which prevents the projector from being used unless
a registered Code is input.
1 Turning on the PIN LOCK
PIN LOCK
1-1 Use the ▲/▼ buttons on the SECURITY menu
to select PIN LOCK and press the ► button or
the ENTER button to display the PIN LOCK on/off
menu.
1-2 Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN
Code box will be displayed.
1-3 Input a 4 part PIN code using the ▲/▼/◄/►
or INPUT button.
The PIN Code again box will appear. Reenter
the same PIN code. This will complete the PIN
code registration.
• If there is no key input for about 55 seconds
while the Enter PIN Code box or the PIN Code again box is displayed,
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power is turned off
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN code is input 3 times, the projector will turn off. Afterwards
the projector will turn off every time an incorrect PIN code is input. The
projector will also turn off if there is no key input for about 5 minutes while
the Enter PIN code box is displayed.
This function will activate only when the projector is started after AC power
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK
2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu.
2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be
displayed.
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn off.
3 If you have forgotten your PIN code
3-1 While the Enter PIN code box is displayed, press and hold the RESET
button for three seconds or press and hold the INPUT button for 3
seconds while pressing the ► button on the projector.
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes
while the Inquiring Code is displayed, the
projector will turn off.
3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will
be sent after your user registration information is confirmed.
(continued on next page)
98
SECURITY menu
Item
Description
If this function is set to ON and the vertical angle of
the projector or the INSTALLATION setting is different
from the previous recorded setting, the TRANSITION
DETECTOR ON alarm will be displayed and the input
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON
alarm, the lamp will turn off.
1 Turning on the TRANSITION DETECTOR
TRANSITION
DETECTOR
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select TRANSITION DETECTOR and press the ►
or the ENTER button to display the TRANSITION
DETECTOR on/off menu.
1-2 Use the ▲/▼ buttons on the TRANSITION
DETECTOR on/off menu to select ON.
Selecting ON will save the setting of the
current angle and the INSTALLATION setting.
ENTER NEW PASSWORD
The ENTER NEW PASSWORD box (small)
box (small)
will be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter a
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, enter the same
password again.
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
the ► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
please make note of the password during this time.
Pressing the ENTER button on the remote control or the ► button on the
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off
the AC power.
• This feature may not function properly if the projector is not in a stable
position when ON is selected.
2 Turning off the TRANSITION DETECTOR
2-1 Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
TRANSITION DETECTOR on/off menu.
ENTER PASSWORD box
If an incorrect password is input, the menu will
(large)
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
99
SECURITY menu
Item
Description
The MY TEXT PASSWORD function can prevent the MY TEXT from being
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD
MY TEXT
PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT PASSWORD and press the
► button to display the MY TEXT PASSWORD
on/off menu.
1-2 Use the ▲/▼ buttons on the MY TEXT
PASSWORD on/off menu to select ON. The
ENTER NEW PASSWORD box (small) will
be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter the
ENTER NEW PASSWORD
box (small)
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, and then enter the
same password again.
1-4 Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press ► button
to display the NOTE NEW PASSWORD box
for about 30 seconds, then please make note
of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will return to the MY TEXT PASSWORD on/off menu.
2 Turning off the MY TEXT PASSWORD
2-1 Follow the procedure in 1-1 to display
the MY TEXT PASSWORD on/off menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
ENTER PASSWORD box
MY TEXT PASSWORD on/off menu.
(large)
If an incorrect password is input, the menu will close.
If necessary, repeat the process from 2-1
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
inquiring code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit inquiring code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
100
SECURITY menu
Item
MY TEXT
DISPLAY
MY TEXT
WRITING
Description
(1) Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT DISPLAY and press the ► or
ENTER button to display the MY TEXT DISPLAY
on/off menu.
(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY
on/off menu to select on or off.
ON ó OFF
When it is set ON, the MY TEXT will be displayed
on the START UP screen and the INPUT_
INFORMATION when the INFORMATION on the
SERVICE menu is chosen.
• This function is available only when the MY TEXT
PASSWORD function is set to the OFF.
(1) Use the ▲/▼ buttons on the
SECURITY menu to select the MY
TEXT WRITING and press the ►
button. The MY TEXT WRITING dialog
will be displayed.
(2) The current MY TEXT will be displayed
on the first 3 lines. If not yet written, the
lines will be blank.
Use the ▲/▼/◄/► buttons and the
ENTER or
button to select and enter
characters. To erase 1 character at one
time, press the RESET button or press
the ◄ and
button at the same time.
Also if you move the cursor to DELETE
or CLEAR ALL on screen and press the
button, 1 character or
ENTER or
all characters will be erased. The MY
TEXT can be input up to 24 characters
on each line.
(3) To change an already inserted
character, press the ▲/▼ button to
move the cursor to one of the first 3
lines, and use the ◄/► buttons to
move the cursor on the character to be
changed.
After pressing the ENTER or
button, the character is selected. Then,
follow the same procedure as described at the item (2) above.
(4) To finish entering text, move the cursor to the OK on screen and press
the ►, ENTER or
button. To revert to the previous MY TEXT without
saving changes, move the cursor to the CANCEL on screen and press
the ◄, ENTER or
button.
• The MY TEXT WRITING function is available only when the MY TEXT
PASSWORD function is set to OFF.
(continued on next page)
101
SECURITY menu
Item
Description
SECURITY
INDICATOR
Selecting this item displays the SECURITY INDICATOR dialog. Use
the ▲/▼ buttons to select ON or OFF.
ON ó OFF
When ON is selected while PIN LOCK or TRANSITION DETECTOR
is ON, the SECURITY indicator blinks in yellow in the standby mode
(98, 99).
STACK LOCK
102
Selecting this item displays the STACK LOCK dialog. For more
information, please see Instant Stack Guide.
Maintenance
Maintenance
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause the
pictures darker or the color tone poor. Note that each lamp has a different lifetime, and
some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare a
new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8960W
Lamp cover
Replacing the lamp
the projector off, and unplug the power cord. Allow
1. Turn
the projector to cool for at least 45 minutes.
a new lamp. If the projector is mounted with
2. Prepare
specified mounting accessories, or if the lamp has broken,
3
also ask the dealer to replace the lamp.
In case of replacement by yourself, follow the following
procedure.
the screw (marked by arrow) of the lamp cover and
3. Loosen
then slide down and lift the lamp cover to remove it.
the 3 screws (marked by arrow) of the
4. Loosen
lamp, and slowly pull the lamp out by the handles.
5.
6.
7.
4, 5
Handles
Never loosen any other screws.
Insert the new lamp, and retighten firmly the 3 screws
of the lamp that are loosened in the previous process to
lock it in place.
While putting the interlocking parts of the lamp cover and
the projector together, slide the lamp cover back in place.
Then firmly fasten the screw of the lamp cover.
Turn the projector on and reset the lamp time using the
LAMP TIME item in the SETUP menu.
6
(1) Press the MENU button to display a menu.
(2) Point at the ADVANCED MENU in the menu using the ▼/▲
button, then press the ► button.
(3) Point at the SETUP in the left column of the menu using the ▼/▲button, then press
the ► button.
(4) Point at the LAMP & FILTER using the ▼/▲button, then press the ► button.
(5) P
oint at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
(6) Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.
CAUTION
taken out.
►Do not touch the interior of the projector, while the lamp is
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
103
Maintenance
Replacing the lamp (continued)
Lamp warning
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp
can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or
worn over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, if the bulb bursts, it is possible
for shards of glass to fly into the lamp housing, and for gas containing mercury and
dust containing fine particles of glass to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For lamp recycling, go to www.lamprecycle.org (in the US).
• For product disposal, consult your local government agency
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, call your dealer.
Disconnect
the plug
from the
power
outlet
104
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the
room well, and make sure not to inhale the gas or fine particles that come out
from the projector's vent holes, and not to get them into your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type. Use of a lamp that does not
meet the lamp specifications for this model could cause a fire, damage or
shorten the life of this product.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light up or to burst.
When the pictures appear dark, or when the color tone is poor, please replace the
lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.
Maintenance
Cleaning and replacing the air filter
Please check and clean the air filter periodically. When the indicators or a message
prompts you to clean the air filter, comply with it as soon as possible.
The filter unit with 2 sheets of filters is inside of the filter cover. In addition, the extra
air filter is attached to inner side of the filter cover. If one of the filters is damaged or
heavily soiled, replace whole filter set with a new one.
Request for a filter set with the following type number from your dealer when
purchasing a new one.
Type number : UX41161
1.
2.
3.
4.
5.
6.
7.
8.
Turn the projector off, and unplug the power
2
cord. Allow the projector to sufficiently cool
down.
Use a vacuum cleaner on and around the
filter cover.
3
Pick and pull up the filter cover knobs to
take it off.
Press up slightly the bottom side knobs
to unlock the bottom side of the filter unit.
Pull the center knob to take the filter unit
off.
Filter cover
Use a vacuum cleaner for the filter vent
knobs
of the projector and the outer side of the
4, 5
filter unit.
Use a vacuum cleaner for the inner side
of each part of the filter unit to clean them
up. If the filters are damaged or heavily
soiled, replace them with the new ones.
Filter unit
knobs
Put the filter unit back in an upright state
into the projector.
8
Put the filter cover back into the place. 7
Filter cover
Filter unit
(continued on next page)
105
Maintenance
Cleaning and replacing the air filter (continued)
9.
Turn the projector on and reset the filter time using the FILTER TIME item in
the EASY MENU.
(1) Press the MENU button to display a menu.
(2) Point at the FILTER TIME using the ▲/▼ cursor buttons, then press the
► cursor (or the ENTER / the RESET) button. A dialog will appear.
(3) Press the ► cursor button to select the “OK” on the dialog. It performs
resetting the filter time.
WARNING ► Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently.
►Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the
like, internal temperatures rise and could cause a fire, a burn or malfunction to
the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as the “CHECK THE AIR FLOW”
or turn off the projector, to prevent the internal heat level rising.
106
Maintenance
Replacing the internal clock battery
Installing the battery is required in some cases. (Event Scheduling in the
User's Manual - Network Guide) A battery is not contained at the time of factory
shipment. Please replace a battery according to the following procedure.
1.
2.
Turn the projector off, and unplug the power cord. Allow the
projector to cool sufficiently.
3.
Turn the battery cover fully in the direction indicated “OPEN”
using a coin or the like, and pick the cover up to
remove it.
Replace the battery with a new HITACHI MAXELL,
Part No.CR2032 or CR2032H.
Slide the battery in under the plastic claw, and push it
into the holder until it clicks.
6.
Replace the battery cover in place, then turn it in the
direction indicated “CLOSE” using such as coins, to fix.
OPEN
CLOSE
90°
OPEN
5.
90°
CLOSE
Pry up the battery using a flathead screwdriver or the like
to take it out. Do not use any metal tools.
While prying it up, put a finger lightly on the battery since it
may pop out of the holder.
OPEN
CLOSE
After making sure that the projector has cooled adequately,
slowly turn over the projector, so that the bottom is facing.
OPEN
CLOSE
4.
Battery Cover
WARNING ►Always handle the batteries with care and use them only as
directed. Battery may explode if mistreated. Do not recharge, disassemble or
dispose of in fire.
And also improper use may result in cracking or leakage, which could result in
fire, injury and/or pollution of the surrounding environment.
・Be sure to use only the batteries specified.
・Make sure the plus and minus terminals are correctly aligned when loading a battery.
・Keep a battery away from children and pets. If swallowed consult a physician
immediately for emergency treatment.
・Do not short circuit or solder a battery.
・Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
・If you observe battery leakage, wipe out the leakage and then replace a battery. If the
leakage adheres to your body or clothes, rinse well with water immediately.
・Obey the local laws on disposing a battery.
107
Maintenance
Other care
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and
inspected by your dealer about once every year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display
quality. Please take care of the lens, being cautious of handling.
the projector off, and unplug the power cord. Allow the projector to cool
1. Turn
sufficiently.
making sure that the projector is cool adequately, lightly wipe the lens
2. After
with a commercially available lens-cleaning wipe. Do not touch the lens
directly with your hand.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint,
etc.
the projector off, and unplug the power cord. Allow the projector to cool
1. Turn
sufficiently.
making sure that the projector is cool adequately, lightly wipe with gauze
2. After
or a soft cloth.
If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner
diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a
soft, dry cloth.
WARNING ►Before caring, make sure the power cord is not plugged in,
and then allow the projector to cool sufficiently. The care in a high temperature
state of the projector could cause a burn and/or malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so
dangerous.
►Avoid wetting the projector or inserting liquids in the projector. It could result in
a fire, an electric shock, and/or malfunction to the projector.
• Do not put anything containing water, cleaners or chemicals near the projector.
• Do not use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the
following. Incorrect care could cause not only an injury but adverse influence
such as discoloration, peeling paint, etc.
►Do not use cleaners or chemicals other than those specified in this manual.
►Do not polish or wipe with hard objects.
NOTICE ►Do not directly touch the lens surface with hands.
108
Troubleshooting
Troubleshooting
If an abnormal operation should occur, stop using the projector immediately.
WARNING ►Never
use the projector if abnormal operations such as
Troubleshooting
smoke, strange odor, excessive sound, damaged casing or elements or cables,
penetration of liquids or foreign matter, etc. should occur. In such cases,
immediately disconnect the power plug from the power outlet. After making sure
that the smoke or odor has stopped, contact to your dealer or service company.
Otherwise if a problem occurs with the projector, the following checks and
measures are recommended before requesting repair.
If this does not resolve the problem, please contact your dealer or service
company. They will tell you what warranty condition is applied.
Related messages
When some message appears, check and cope with it according to the following
table. Although these messages will be automatically disappeared around several
minutes, it will be reappeared every time the power is turned on.
Message
Description
There is no input signal.
Please confirm the signal input connection, and the
status of the signal source.
Projector is waiting for an image file.
Check the hardware connection, settings on the projector
and network-related settings.
The computer-Projector network connection might be
disconnected. Please re-connect them.
(continued on next page)
109
Troubleshooting
Related messages (continued)
Message
Description
The horizontal or vertical frequency of the input
signal is not within the specified range.
Please confirm the specs for your projector or the signal
source specs.
An improper signal is input.
Please confirm the specs for your projector or the signal
source specs.
The internal temperature is rising.
Please turn the power off, and allow the projector to cool
down at least 20 minutes. After having confirmed the
following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Please use the unit within the usage temperature
parameters (0°C to 35°C or 40°C (User's Manual
(concise))).
• Is the setting for ALTITUDE appropriate?
• Is the exhaust air (hot/cold) from peripheral
equipments blowing against the ventilation opening of
projector?
For details of ALTITUDE, refer to ALTITUDE of SERVICE
in the OPTION menu (88). If the projector is used with
a wrong setting, it may cause damage to the projector
itself or the parts inside.
(continued on next page)
110
Troubleshooting
Related messages (continued)
Message
Description
A note of precaution when cleaning the air filter.
Please immediately turn the power off, and clean or
change the air filter referring to the Cleaning and
replacing the air filter section of this manual. After you
have cleaned or changed the air filter, please be sure to
reset the filter timer (70, 106).
The button operation is not available.
Check the button you are going to use (7).
111
Regarding the indicator lamps
Troubleshooting
Regarding the indicator lamps
The indicators may differ from usual, check and cope with it according to the
following table.
The indicators are described as below.
Lit
Steady light
Blinking
Off
Indicator Status
Description
The projector is in a standby state.
Orange
Please refer to the section “Power on/off”.
The projector is warming up.
Green
Please wait.
The projector is in an on state.
Green
Ordinary operations may be performed.
The projector is cooling down.
Orange
(continued on next page)
112
Please wait.
Regarding the indicator lamps
Regarding the indicator lamps (continued)
Indicator Status
descretionary
Red
Description
The projector is cooling down. A certain error
has been detected.
Please wait until POWER indicator finishes blinking,
and then perform the proper measure using the item
descriptions below.
The lamp cover has not been properly fixed.
Red
Red
Please turn the power off, and allow the projector to
cool down at least 45 minutes. After the projector has
sufficiently cooled down, please make confirmation
of the attachment state of the lamp cover. After
performing any needed maintenance, turn the power
on again. If the same indication is displayed after
the remedy, please contact your dealer or service
company.
The cooling fan is not operating.
Red
Red
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation
that no foreign matter has become caught in the fan,
etc., and then turn the power on again.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
The lamp does not light, and there is a
possibility that interior portion has become
heated. Otherwise, AC power supply is
unstable (ACBLK).
Red
Red
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Please use the unit within the temperature range.
NORMAL MODE: 0 to 35°C
ECO MODE: 0 to 40°C
If the same indication is displayed after the remedy,
please change the lamp referring to the section
Replacing the lamp.
(continued on next page)
113
Regarding the indicator lamps
Regarding the indicator lamps (continued)
Indicator Status
Red
Red
Description
There is a possibility that the interior portion
has become heated.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Please use the unit within the temperature range.
NORMAL MODE: 0 to 35°C
ECO MODE: 0 to 40°C
• Is the setting for ALTITUDE appropriate?
• Is the exhaust air (hot/cold) from peripheral
equipments blowing against the ventilation opening
of projector?
For details on ALTITUDE, refer to ALTITUDE of
SERVICE in the OPTION menu. If the projector is
used with a wrong setting, it may cause damage to
the projector itself or the parts inside.
It is time to clean the air filter.
Red
Red
Blinking at the
same time
Red
(continued on next page)
114
Please turn the power off immediately, and clean or
change the air filter referring to the section Cleaning
and replacing the air filter. After cleaning or
changing the air filter, please be sure to reset the
filter timer.
After the remedy, restart the projector.
This is a Lamp Error.
Lamp is turned off.
Please turn the power off, and allow the projector to
cool down at least 45 minutes. Restart the projector.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
Regarding the indicator lamps
Regarding the indicator lamps (continued)
Indicator Status
Yellow
Description
PIN LOCK function is active.
Please see SECURITY menu > PIN LOCK(98)
If the same indication is displayed after the remedy,
please contact your dealer or service company.
Red
Blinking
alternately
Green
There is a possibility that the interior portion
has become overcooled.
• Please use the unit within the temperature range.
NORMAL MODE: 0 to 35°C
ECO MODE: 0 to 40°C
AC BLACKOUT error has occured.
(continued on next page)
115
Regarding the indicator lamps
Regarding the indicator lamps (continued)
NOTE • When the interior portion has become overheated, for safety
purposes, the projector is automatically shut down, and the indicator lamps
may also be turned off. In such a case, disconnect the power cord, and wait at
least 45 minutes. After the projector has sufficiently cooled down, please make
confirmation of the attachment state of the lamp and lamp cover, and then turn
the power on again.
For the SECURITY indicator, see SECURITY INDICATOR in the SECURITY
menu (102).
Resetting all settings
When it is hard to correct some wrong settings, the FACTORY RESET function of
SERVICE item in OPTION menu (94) can reset all settings (except settings such
as LANGUAGE, AUTO BLANK, LAMP TIME, FILTER TIME, FILTER MESSAGE,
STANDBY MODE, COMMUNICATION, SECURITY and NETWORK)
to the factory default.
116
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
About the phenomenon confused with a machine defect, check and cope with it
according to the following table.
Phenomenon
Cases not involving a machine defect
The electrical power cord is not plugged in.
Correctly connect the power cord.
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Please disconnect the power plug from the power outlet,
and allow the projector to cool down at least 10 minutes,
then turn the power on again.
Power does not
come on.
Either there is no lamp and/or lamp cover, or either
of these has not been properly fixed.
Please turn the power off and disconnect the power
plug from the power outlet, and allow the projector to
cool down at least 45 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the attachment state of the lamp and lamp cover, and
then turn the power on again.
The signal cables are not correctly connected.
Correctly connect the connection cables.
Neither sounds
nor pictures are
output.
Reference
page
26
26
103
12 ~ 21
Signal source does not correctly work.
Correctly set up the signal source device by referring to
the manual of the source device.
–
The input changeover settings are mismatched.
Select the input signal, and correct the settings.
33
The BLANK function for pictures and the MUTE
function for sounds are working.
AV MUTE may be active.
Refer to the item “Sound does not come out” and “No
pictures are displayed” on the next page to turn off the
MUTE and BLANK functions.
32
(continued on next page)
117
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
Sound does not
come out.
No pictures are
displayed.
Cases not involving a machine defect
The signal cables are not correctly connected.
Correctly connect the audio cables.
12 ~ 21
The volume is adjusted to an extremely low level.
Adjust the volume to a higher level using the menu
function or the remote control.
32, 75
The AUDIO SOURCE/SPEAKER setting is not correct.
Correctly set the AUDIO SOURCE/SPEAKER in AUDIO
menu.
75
The Sound button (♪) or checkbox is disabled.
If you have selected LAN, remove the check mark from
the Sound checkbox in the Option menu of “LiveViewer”.
–
The MUTE function is working.
Restore the sound pressing MUTE or VOLUME +/button on the remote control.
32
The signal cables are not correctly connected.
Correctly connect the connection cables.
12 ~ 21
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu
function.
56
The computer cannot detect the projector as a plug
and play monitor.
Make sure that the computer can detect a plug and play
monitor using another plug and play monitor.
12
The lens shade is closed.
Press SHADE button (MY BUTTON) on the remote control.
84
The BLANK screen is displayed.
Press BLANK button on the remote control.
46
(continued on next page)
118
Reference
page
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
Cases not involving a machine defect
The remote
The batteries in the remote control are near the end.
control does not
Replace the batteries.
work.
Video screen
display freezes.
Colors have
a faded-out
appearance,
or color tone is
poor.
Pictures appear
dark.
The FREEZE function is working.
Press FREEZE button to restore the screen to normal.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR TEMP,
COLOR and/or TINT settings, using the menu functions.
27
46
56, 58
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB,
SMPTE240, REC709 or REC601.
63
The brightness and/or contrast are adjusted to an
extremely low level.
Adjust BRIGHTNESS and/or CONTRAST settings to a
higher level using the menu function.
56
The projector is operating in Eco mode.
Set ECO MODE in the LAMP & FILTER menu to NORMAL.
69
The lamp is approaching the end of its product
lifetime.
Replace the lamp.
103
Dimming Level of Blending function is working.
Set Dimming Level to a higher level or set Blending Mode to OFF.
The lens cover is attached.
Remove the lens cover.
Pictures appear
blurry.
Reference
page
Either the focus and/or horizontal phase settings are
not properly adjusted.
Adjust the focus using the focus ring, and/or H PHASE
using the menu function.
41, 44
–
35, 62
(continued on next page)
119
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
Cases not involving a machine defect
Reference
page
Pictures
appear blurry.
(continued)
The lens is dirty or misty.
Clean the lens referring to the section Caring for the lens.
108
When the projector is operating in Eco mode,
flickering may appear on screen.
Set ECO MODE in the LAMP & FILTER menu to NORMAL.
69
The OVER SCAN ratio is too big.
Adjust OVER SCAN in the IMAGE menu smaller.
61
Excessive VIDEO NR.
Change the setting of VIDEO NR in the INPUT menu.
63
The FRAME LOCK function cannot work on the
current input signal.
Set FRAME LOCK in the INPUT menu to OFF.
65
The SAVING function is working.
Select NORMAL for STANDBY MODE item in the
SETUP menu.
72
Some kind
of image
degradation
such as
flickering or
stripes appear
on screen.
RS-232C is set to HDBaseT.
RS-232C does
Select CONTROL for RS-232C item in the OPTION
not work on
control terminal. menu.
93
The COMMUNICATION TYPE for the CONTROL port
is set to NETWORK BRIDGE.
Select OFF for COMMUNICATION TYPE item in the
OPTION - SERVICE - COMMUNICATION menu.
90
The SAVING function is working.
Select NORMAL for STANDBY MODE item in the
SETUP menu.
72
The same network address is set for both wireless
and wired LAN.
Change the network address setting for wireless or wired
LAN.
–
Displayed
image is
partially dark.
Blending Region is set.
Set all Blending Region to OFF or set Blending – Mode
to OFF.
41
ECO MODE
setting cannot
be changed.
Blending - Mode is set to MANUAL.
Set Blending – Mode to OFF.
41
Network does
not work.
(continued on next page)
120
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
Cases not involving a machine defect
Reference
page
The IR and
RS-232C does
not work on
HDBaseTTM
connection.
The SAVING function is working.
Select NORMAL for STANDBY MODE item in the
SETUP menu.
72
RS-232C
does not work
on HDBaseT
connection.
RS-232C is set to CONTROL.
Select HDBaseT for RS-232C item in the OPTION menu.
93
HDBaseT
connection
does not work.
IR and LAN
does not work
via HDBaseT.
LAN does not
work, if LAN is
connected to
the projector
while having
an input signal
from HDBaseT.
The SAVING function is working.
Select NORMAL for STANDBY MODE item in the
SETUP menu.
72
The connected equipment may not be supported by
HDBaseT.
Refer to User's manual(detailed) for connection.
13
Check if the IR setting is OFF under HDBaseT.
EASY MENU > ADVANCED MENU > OPTION >
SERVICE > REMOTE RECEIV.
89
Check if the LAN setting is HDBaseT.
EASY MENU > ADVANCED MENU > OPTION
> SERVICE > CONTROL TERMINAL > WIRED
NETWORK
–
Check if the LAN setting is HDBaseT.
EASY MENU > ADVANCED MENU > OPTION
> SERVICE > CONTROL TERMINAL > WIRED
NETWORK
–
This projector is compatible with 100BASE-T only.
Check the specification of the connected equipments.
–
If the LAN cable is connected with the hub, try to change
the connected port at the hub
–
If the LAN cable is connected directly to the computer,
try to connect to other computer
–
(continued on next page)
121
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
No image is
displayed via
HDBaseT.
NETWORK
BRIDGE
function does
not work.
Schedule
function does
not work.
MHL power
feeding does
not work with
standby mode.
STANDBY
OUTPUT
(AUDIO OUT,
MONITOR OUT,
HDMI OUT)
does not work
with standby
mode.
Cases not involving a machine defect
Check the LAN cable if it is CAT5e certified or higher.
–
Try to change the LAN cable.
–
If the LAN cable is connected with more than 3 extension
connector, the transmission of 100 meters may fail.
–
Check if the extension connector is compatible with
CAT5e.
All LAN cable and extension connector connected with
HDBaseT port must be CAT5e certified.
–
The NETWORK BRIDGE function is turned off.
Select NETWORK BRIDGE for COMMUNICATION TYPE
item in the OPTION - SERVICE - COMMUNICATION
menu.
90
The SAVING function is working.
Select NORMAL for STANDBY MODE item in the
SETUP menu.
72
The internal clock has been reset.
Once you turn off the projector in the SAVING mode or
the AC power, the current date and time setting is reset.
Check the SCHEDULE setting for WIRELESS SETUP or
WIRED SETUP in the NETWORK menu.
–
MHL STANDBY PWR. function is not working.
When the STANDBY MODE is set to SAVING, MHL
power feeding is unavailable with standby mode. Select
NORMAL for STANDBY MODE item in the SETUP
menu, then select ON for MHL STANDBY PWR. item in
the INPUT menu.
67
Check if SAVING is set in SETUP - STANDBY MODE.
Set NORMAL in the menu above.
If the signal is not output yet, check if a desirable item is
set in SETUP - STANDBY OUTPUT.
(continued on next page)
122
Reference
page
72
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Phenomenon
Cases not involving a machine defect
Reference
page
Check if PROJECTOR is set in OPTION - SERVICE -
The signal from HDMI OUT RESOLUTION.
HDMI OUT is
Set EXTERNAL DEVICE in the menu above.
not output in the
external device. If the signal is not output yet, check the supported
93
The signal from Check if EXTERNAL DEVICE is set in OPTION HDMI OUT is
SERVICE - HDMI OUT RESOLUTION.
not output in
Set PROJECTOR in the menu above.
other connected
projectors.
93
resolution of the external device.
When the
projector is
connected to
the network, it
powers off and
on as described
below.
Powers off
POWER
indicator blinks
in orange a few
times
Goes into
standby mode
Disconnect the LAN cable and check that the
projector is working properly.
If this phenomenon occurs after connecting to the
network, there may be a loop between two Ethernet
switching hubs within the network, as explained below.
-There are two or more Ethernet switching hubs in a
network.
- Two of the hubs are doubly connected by LAN cables.
- This double connection forms a loop between the two
hubs.
Such a loop may have an adverse effect on the projector
as well as the other network devices.
Check the network connection and remove the loop by
disconnecting the LAN cables such that there is only one
connecting cable between two hubs.
–
NOTE • Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and it does not constitute or
imply a machine defect.
123
Specifications
Specifications
Please see the Specifications in the User’s Manual (concise) which is a book.
End User License Agreement for the Projector Software
• Software in the projector consists of the plural number of independent software
modules and there exist our copyright and/or third party copyrights for each of
such software modules.
• Be sure to read “End User License Agreement for the Projector Software” which
is separated document.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
avservice@dukane.com
www.dukaneav.com
124
430-8960W-8961WU-8962WU-8963-General-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising