ACC-5595 - Platforma Internetowa ASTOR.

ACC-5595 - Platforma Internetowa ASTOR.
GE
Intelligent Platforms
ACC-5595
2 Gb/s Reflective Memory Hub Assembly
Features
• For use with GE Intelligent Platforms 5565
Reflective Memory network of products
• Provides up to eight ports using small form
factor pluggable (SFP) transceivers
• Hub assemblies can be cascaded with a
maximum of 256 nodes
• Automatically bypasses defective or disconnected nodes in a fiber-optic network
• Automatic bypass can be optionally
controlled by the loss of signal or by the
loss of sync pattern
• Each port regenerates the serial optical
signal, eliminating link losses and reducing jitter
• Configurable for use with cables up to
10 km in length
• 10BaseT Ethernet TCP/IP port for remote
access and control
• RS232 port for local access and control
• Optional 19 - inch 1U rack mount or
desktop enclosure
• Internal universal power supply
• Dark on Dark option turns off the board’s
transmitter if the receiver does not detect
a signal (available for firmware versions
02.00 and later)
The ACC-5595 is a managed hub designed
to operate with the GE Intelligent Platforms
5565 family of Reflective Memory real-time
network products. The Reflective Memory
hub can automatically bypass ports when
it detects a loss of signal or the loss of valid
synchronization patterns, allowing the other
nodes in the network to remain operational.
Since the optical ports are implemented
with small form factor pluggable (SFP) transceivers, only the required ports need to be
populated. The ACC-5595 SFP transceivers
can be a combination of either multimode
(short distance) or single-mode (long distance) transceivers. This feature permits a
cost saving in small networks as well as system optimization. For larger networks, several
ACC-5595 assemblies can be cascaded,
permitting a managed hub array with up to
256 nodes. Each port regenerates the serial
optical signal, eliminating the problems with
insertion losses and cable attenuation. Signal
regeneration also reduces jitter. The RS232
port gives you the ability to monitor and control your Reflective Memory network through
a simple PC serial port. The Ethernet port
feature allows you to monitor and control
the hub from great distances through a local
area network (LAN) or via a Web browser.
As an option, the ACC-5595 can be configured
as a 19-inch 1U rack-mountable enclosure or
as a desktop enclosure. The universal power
supply permits operation with nearly any
international power standard.
The ACC-5595 automatically bypasses ports
when the absence of valid synchronization
patterns is detected. Three LEDs, adjacent to
each port, provide a visual indication of the
port status. Additional status indications and
modes of operation are available through
either the serial port or the Ethernet port.
Status information includes the detection of
installed transceivers, the detection of signal
(light), the detection of valid synchronization patterns and the port operation speed
(2 Gb/s). Control registers allow the channel
bypass to be based on the absence of a single valid synchronization pattern or multiple
synchronization patterns. A bypass can also
be based simply on the loss of a signal (light).
In addition, each port can be manually forced
either active or bypassed regardless of the
status indicators.
An additional control register permits the transmitter of any port to be manually disabled.
ACC-5595 2 Gb/s Reflective Memory Hub Assembly
Front panel manual switches include a
recessed momentary reset switch and a
Gang Select switch. The Gang Select switch
configures the ACC-5595 ports as one loop
of eight ports or two separate loops of four
ports each.
• Single-Mode (10 km) Cable Length:
80 km (maximum)
• Dark on Dark: The Dark on Dark option
turns off the board’s transmitter if the
receiver does not detect a signal (available
for firmware versions 02.00 and later).
Functional Characteristics
Ethernet Controller: 10BaseT interface is compliant with Transmission Control Protocol/
Internet Protocol (TCP/IP) standards. Each hub
assembly will have a unique MAC address.
The hub assembly can operate on either a
LAN or a wide area network (WAN).
• Multimode Port Wavelength: 830 to 860 nm
• Multimode Cable Length: 300 m (maximum)
• Single-Mode (10km) Port Wavelength:
1,300 to 1,335 nm
• Single-Mode (10 km) Cable Length:
10 km (maximum)
• Single-Mode (80 km) Port Wavelength:
1,540 to 1,570 nm
connection. The remote interface is controlled by the use of standard HTML-based
Web browsers. The user interface presents
status data, such as “loss of signal” and “sync
detect” information. Bypass mode, “Dark on
Dark’ and the ability to force each port on/off
or automatic are supported. These settings
are retained in NVRAM.
The ACC-5595 includes a remote user interface available through a standard Ethernet
Block Diagram
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
SFP7
Transceiver
SFP6
Transceiver
SFP5
Transceiver
SFP4
Transceiver
SFP3
Transceiver
SFP2
Transceiver
SFP1
Transceiver
SFP0
Transceiver
Sync
Detect
Unit7
Sync
Detect
Unit6
Sync
Detect
Unit5
Sync
Detect
Unit4
Sync
Detect
Unit3
Sync
Detect
Unit2
Sync
Detect
Unit1
Sync
Detect
Unit0
1
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
0
Universal
Power Supply
Status & Control
10BaseT
Ethernet
Port
RS232
Port
Ethernet
RS232
Reset
Switch
Front Panel
Gang
Select
Switch
Power Switch,
Fuse,
IEC Receptacle
Rear Panel
ACC-5595 2 Gb/s Reflective Memory Hub Assembly
Cascade of Three ACC-5565s with 24 Nodes
ACC-5595
Port 0
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
Node 1
xxx-5565
ACC-5595
Node 3
xxx-5565
Node 4
xxx-5565
Node 5
xxx-5565
Node 6
xxx-5565
Node 7
xxx-5565
Port 0
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
Node 8
Node 9
Node 10
Node 11
Node 12
Node 13
Node 14
Simplex Cable
CBL-000-F5-0xx
ACC-5595
Node 2
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
Port 0
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
TX RX
Duplex Cable
CBL-000-F6-0xx
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
RX TX
Node 15
Node 16
Node 17
Node 18
Node 19
Node 20
Node 21
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
xxx-5565
ACC-5595 2 Gb/s Reflective Memory Hub Assembly
Specifications
Ordering Information
Desktop Assembly Dimensions
• 16.73 inches wide by 10.0 inches deep by (1U) 1.72
inches high. Dimensions do not include nonskid selfadhesive feet.
ACC-5595
-
Rack Mount Assembly Dimensions
• The basic dimensions are the same as the desktop
assembly, but include two 1U rack mount brackets
for the standard 19-inch rack.
A
B
C
0
A = Enclosure Options
0 = Reserved 1 = Reserved
2 = Rack Mount or Desktop
B = Number of Single-Mode (10km) Pluggable Transceivers
0, 1, 2, 3, 4, 5, 6, 7, or 8
Front Panel Connectors
• 8 SFP transceivers. The SFP receptacles not populated with transceivers contain EMI dust plugs.
There is one RJ45 Ethernet connector and one 9-pin
female D-subminiature RS232 connector.
C = Number of Multimode Pluggable Tranceivers
0, 1, 2, 3, 4, 5, 6, 7, or 8
Cabling
• Each installed SPF transceiver requires either one
Duplex LC-type fiber-optic cable or two Simplex
LC-type fiber-optic cables. The Simplex cables are
best suited for cascading hubs. The Duplex cables
can be used for all other interconnectivity.
CBL-000-F5
-
Rear Panel Connectors
• A power entry module that includes a power ON/OFF
switch, a 4A/250V fuse, and a globally accepted
IEC receptacle.
Fuse
• 1 A, 250 V, 5 x 20 mm, fast acting, IEC 60127-2
standard glass or equivalent
MTBF
• Total fit x qty: 2,317.3641
• MTBF (hours): 431,524.76
Power Requirements
• 90 to 264VAC
• 47 to 440Hz
• 25W. Power supply and power entry module meet
safety standards: UL, C-UL: UL 1950 TUV: EN69050
CE: EN55022, EN61000-4-2, 3, 4, 5; EN61000-3-2
Environmental
• Temperature
- Operating:
- Storage: • Relative Humidity
- Operating:
- Storage:
Simplex Cable Specifications
Fiber-optic cable - Multimode 62.5 micron core
A
ABC = Cable Lengths
000 = 0.5 ft (01.5 m)
001 = 1 ft (0.31 m)
002 = 5 ft (1.52 m)
003 = 10 ft (3.04 m)
004 = 25 ft (7.62 m)
B
C
005 = 50 ft (15.24 m)
006 = 80 ft (24.40 m)
008 = 150 ft (45.72 m)
009 = 200 ft (60.98 m)
010 = 250 ft (76.20 m)
011 = 350 ft (106.68 m)
012 = 500 ft (152.15 m)
013 = 574 ft (175 m)
014 = 656 ft (200 m)
016 = 1,000 ft (304.30 m)
Duplex Cable Specifications
Fiber-optic cable - Multimode 62.5 micron core
CBL-000-F6
-
ABC = Cable Lengths
000 = 3 ft (1 m)
001 - 6 ft (2 m)
002 = 10 ft (3 m)
003 = 16 ft (5 m)
004 = 32 ft (10 m)
005 = 66 ft (20 m)
A
B
C
006 = 98 ft (30 m)
007 = 164 ft (50 m)
008 = 230 ft (70 m)
011 = 426 ft (130 m)
012 = 492 ft (150 m)
013 = 557 ft (170 m)
014 = 656 ft (200 m)
015 = 721 ft (220 m)
016 = 754 ft (23 0)
017 = 820 ft (250 m)
018 = 885 ft (270 m)
019 = 984 ft (300 m)
Note:
Sum of B + C + D Modules should be less than or equal to 8.
0° to +65°C
-40° to +85°C
20% to 80%, noncondensing
20% to 80%, noncondensing
Regulatory Compliance
• European Union (CE Mark)
- EN55024
- EN55022 Radiated Emissions Class A
- EN55022 Conducted Emissions Class A
- EN61000-4-2 (ESD)
- EN61000-4-3 (Radiated Immunity)
- EN61000-4-4 (EFT)
- EN61000-4-5 (Surge)
- EN61000-4-6 (Conducted RF)
- EN61000-4-8 (Power Frequency Magnetic Fields)
• United States FCC Part 15, Class A
• Canada ICES-003, Class A
• UL60950
• EN60950(LVD)
About GE Intelligent Platforms
GE Intelligent Platforms, a General Electric Company (NYSE: GE), is an experienced high-performance
technology company and a global provider of hardware, software, services, and expertise in automation
and embedded computing. We offer a unique foundation of agile, advanced and ultra-reliable technology
that provides customers a sustainable advantage in the industries they serve, including energy, water,
consumer packaged goods, government and defense, and telecommunications. GE Intelligent Platforms
is a worldwide company headquartered in Charlottesville, VA and is part of GE Home and Business Solutions.
For more information, visit www.ge-ip.com.
GE Intelligent Platforms Contact Information
Americas: 1 800 433 2682 or 1 434 978 5100
Global regional phone numbers are listed by location on our web site at www.ge-ip.com/contact
www.ge-ip.com
©2010 GE Intelligent Platforms, Inc. All rights reserved.
All other brands or names are property of their respective holders.
Specifications are subject to change without notice.
01.10 GFA-1227A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising