SSP118 Profundo Powered Subwoofer

Owner’s Manual

www.bassboss.com

©

®

2016 True Lee Loudspeakers, LLC – [email protected] – 512-368-3268 855-8-BASS-70 Toll Free

SSP118 Profundo Powered Subwoofer

Owner’s Manual

TABLE OF CONTENTS

Overview..................................................................................... 3

Technical Specifications............................................................ 4

Dimension Drawings ................................................................. 5

Frequency Response Graph ...................................................... 5

Safety Information..................................................................... 6

Setup Instructions...................................................................... 7

Troubleshooting......................................................................... 7

Operation................................................................................... 8

Warranty..................................................................................... 9

Export Warranty......................................................................... 9

FCC Compliance Notice.............................................................. 10

Need more assistance? Support is available via phone or email.

Email: [email protected]

Phone: 855-822-7770 toll free or 512-368-3268

Web Site: www.bassboss.com

SSP118 Profundo Powered Subwoofer

• Solid, Flat Response Down To 30 Hz

• Easy To Transport and Set Up

• Reliable, Protected, Self-Powered System

• Excellent Output-To-Size Ratio

• 2400W RMS Class D Amplifier

• Powerful, Loud, Deep Bass

The SSP118 is a high-powered self-amplified single 18-inch subwoofer designed to give you the low frequency output of an average double 18”in a single 18”box.The SSP118 features a single 18-inch subwoofer enclosure with a highpowered 2400 Watt Class-D amplifier.

Each SSP118 Powered Subwoofer gives you low frequency output to 30 Hz, typical of an average double 18”, from a single 18”box.

Delivering output to frequencies lower than many double 18” cabinets, each individual SSP118 enclosure does so with nearly half the space and considerably less weight.This is a very practical consideration from both a size and cost point of view. Each

SSP118 will give you more low-bass output than others of similar size and price because it is designed to give you the low frequency output of an average double 18” from a single 18” box.

For Mobile Professionals who provide superior sound quality, the SSP118 allows you to deliver premium service with less equipment and labor.

With two SSP118 Subwoofers, you will have the output of one of the worlds finest double-18" subwoofers, just divided into two smaller, more manageable pieces.

Optimized for remarkably deep bass response from a cabinet of manageable size, SSP118 Subwoofers are each loaded with a single 18"long-excursion, neodymium motor, low frequency driver.

Each driver has a 4” voice coil and is rated for 1500W nominal power handling, 3000W program power handling. Practically impossible to blow drivers, thanks to the combination of extremely rugged, very high power handling, long excursion drivers, carefully optimized cabinet and port design and several effective but transparent protection systems.The protection systems prevent thermal overload of the voice coils and minimize long-term thermal compression while having virtually no effect on the transient response and peak output of the loudspeakers.

Extremely flat, delivering response that is +- 3.0dB from 30Hz to 100Hz.

No equalization is required to achieve this response.

Unlike designs that require equalization, the SSP118’s tone, response and sensitivity are native to the design. Systems that require processing to achieve their stated response are still subject to the physical excursion and thermal limits of their drivers. Boosting low frequency EQ to achieve extended low-frequency response results in excessive distortion or woofer damage at full power unless limiting is applied.The limiting necessary to prevent failure also prevents the realization of their claimed frequency response at full power.The

SSP118 does not suffer from these limitations. It faithfully delivers the low bass where most others either roll off or die trying.

Finished in extremely durable black textured weatherproof polyurethane coating

.A top-mounted pole socket in each SSP118 provides for mid-high loudspeakers to be mounted on a straight speaker pole above the subwoofer.The enclosures also feature four large rubber feet and corresponding recesses in their tops to facilitate interlocking the boxes when stacked.The woofers' cones are made from a waterproof fiber matrix which can withstand exposure to spills and rain and can be wiped clean with a damp cloth.

Page 3

Performance

Loudspeaker Description:

Frequency Response (±3 dB):

Maximum Sustained Output:

Short-term Peak Output:

Nominal Dispersion (°H x °V):

Power

Amplification:

Processing:

Electrical Input Connector:

Electrical Connector, Mains

Voltage Operating Range:

Current Draw, Nominal:

Signal Input Connector:

Signal Output Connector:

Physical

Enclosure Type:

Transducers:

Cabinet Construction:

Dimensions (H x W x D):

Net Weight:

Exterior Finish:

Grill:

Suspension System:

Optional

Cover:

Transport Dollies:

Flying Hardware:

Installation Version:

Amplification for Installation:

Online Information:

Single 18" Subwoofer

30-100Hz

130 dB SPL, 1m, 2pi, half-space, (ground stacked)

136 dB

360 x 360

Response Graph

2400 Watt RMS Class D Amplifier

Integrated comprehensive DSP provides high pass, low pass, time alignment and limiting

Neutrik Powercon input (Blue) NAC3FCA

NEMA5-15 (Edison) or L530, upon request

90-132VAC, 55-65Hz

565 W, 4.7A

XLR-F

XLR-M pass-through only

Direct radiating, vented enclosure, optimally tuned for low frequency response with high sensitivity and high power handling

1 x 18 in. diameter (457 mm) woofer with 4 in. (100 mm) copper winding voice coil and 56 mm (2.2") peak to peak excursion. Waterproof fiber composite cone

18mm Baltic Birch plywood. Equipped with 2 handles and interlocking rubber feet

22.5" x 30" x 24" (23.25" high with feet)

125 lbs

Weatherproof bonded high-pressure polyurethane

Perforated, powder-coated steel

16x 3/8-16 threaded flypoints

Heavy-duty padded nylon transport covers for 1 to 2 cabinets

Dolly cart with 4 locking casters and recesses to accept interlocking cabinet feet for transporting 1 or 2 cabinets

Side-pull anchors and/or shoulder eyebolts

Available without handles and pole sockets

Complete power package including DSP in two space rack chassis www.bassboss.com/ssp118

Page 4

Page 5

SAFETY INFORMATION

Important information regarding safety and the use of your loudspeakers:

Never stand in the immediate vicinity of loudspeakers driven at a high level.Professional loudspeaker systems are capable of causing a sound pressure level detrimental to human health. Seemingly non-critical sound levels (from approx. 95 dB SPL) can cause hearing damage if people are exposed to it over a long period. To prevent potentially dangerous exposure to high levels of acoustic pressure, anyone who is exposed to these levels should use adequate protection devices.

When a transducer capable of producing high sound levels is being used,it is therefore necessary to wear ear plugs or protective earphones.

See the manual technical specifications to know the maximum sound pressure level.

In order to prevent accidents when setting up the loudspeakers or loudspeaker stands, make sure they are standing on a firm surface.

Ensure that all additional hardware, fixings and fasteners used for installation or mobile deployment are of an appropriate size and load safety factor.

Pay attention to the manufacturers' instructions and to the relevant safety guidelines.

Regularly check the loudspeaker housings and accessories for visible signs of wear and tear, and replace them when necessary.

Regularly check all load bearing bolts in the mounting devices.

Caution: Loudspeakers produce a static magnetic field even if they are not connected or are not in use. Therefore make sure when erecting and transporting loudspeakers that they are nowhere near equipment and objects which may be impaired or damaged by an external magnetic field. A distance of 3 feet (1m) should be maintained between loudspeakers and sensitive equipment such as CRT monitors or magnetic storage media.

Never attempt to carry out any operations, modifications or repairs that are not expressly described in this manual.

Contact your dealer or BASSBOSS support if the product is not functioning properly.

BASSBOSS strongly recommends this product be installed by a qualified,professional installer who can ensure correct installation and certify that is is installed in compliance with the regulations in force.

The entire audio system must comply with the current local standards and regulations regarding electrical systems.

IMPORTANT NOTES

To prevent the occurrence of noise on signal cables, use shielded cables only. Avoid routing signal cables close to equipment that produces high-intensity electromagnetic fields such as transformers, power cables and loudspeaker wires. Do not coil excess power cable. Do not coil or wrap power cables and signal cables together.

Page 6

SET UP INSTRUCTIONS

1. Place loudspeaker in the desired location. Ensure that it is secure and stable.

2. Rotate the input attenuator knob counterclockwise to the lowest setting.

3. Connect signal from the sound source (mixer) via the XLR female input jack.

4. Connect the XLR male output to the next available loudspeaker input via an XLR cable (if applicable.) This is a full-range pass-through connection and no processing is applied to this output.

5. Connect the Neutrik PowerCON (blue) connector to the blue power inlet socket. Do not force.To insert, align the indexing tabs on the connectors, insert the plug fully into the socket and rotate clockwise until the latches catch.To remove, pull back on the latch tab and rotate the connector counterclockwise to the index stop, then pull outwards.

6. The white PowerCON connector is used to daisy-chain mains power to a second amplified loudspeaker. The total current draw of all loudspeakers connected through a single PowerCON must not exceed 20A. Make all PowerCON connections before plugging in to mains power.

7. Connect the electrical plug to a power source.

8. Move the POWER switch to the ON position.

9. Move the Standby* switch to the ON position (if applicable)

10. Rotate the input attenuator clockwise to achieve the desired sound level.

Standby Switch: (Installation Addendum)

3-position switch that allows selection between ON, AUTO and 12V Trigger when the mains POWER switch is ON and power is connected to the amplifier. This feature is enabled primarily for installations where remote powering is desired.It is disabled for portable applications.Many portable products will not have this feature.If you use your amplifier for portable applications and this feature is available,leave the switch in the ON position.

In ON position, amplifier remains on when the POWER switch is on. In AUTO position, the amplifier will switch to Standby mode when no signal is present and will power on when it senses incoming signal. In OFF/12V position, the amplifier will remain OFF until a 12V trigger signal is applied to the trigger inputs.

TROUBLESHOOTING

If,after following the above instructions for setup,you have no output from the loudspeakers,please check the following:

Verify that the green power (ON) LED is lit. If not, check the following:

1. Is the power cord plugged into a live outlet?

2. Is the Neutrik PowerCON connector rotated into the locked position?

3. Is the Standby Switch in the ON position?

If the green power LED is on, check the following:

1. Is the signal cable connected to the input?

2. Is the signal cable connected to an operating output at the other end?

3. Is the signal flowing to the input? Check the integrity of the cable.

4. Is the attenuator turned all the way down or at a very low level?

5. Is the signal flowing to the input full-range? Filters in the signal may remove the operating frequencies of the loudspeaker receiving them.

Need more assistance? Support is available via phone or email.

Email: [email protected]

Phone: 855-822-7770 toll free or 512-368-3268 Web Site: www.bassboss.com

Page 7

OPERATION

There are 4 control knobs on the amplifier.

1: GAIN

Provides attenuation of the input from off to full output. Use appropriate gain structure to ensure the output feeding the subwoofer doesn't reach clipping and distortion before maximum desired sound level is achieved. The amplifier has a complement of limiters and safeties to protect itself and the driver however if audible distortion occurs,lower the level of the incoming signal.

2: LF ADJUST

Provides from 0 to 6dB of boost centered at 80Hz to increase "Punch". Particularly useful when the SSP118 is used with smaller tops that lack impact in the region of transition between the top and the sub.

3: CROSSOVER

Provides adjustment of the low-pass filter frequency from 68Hz (when fully counterclockwise) to 80Hz (when fully clockwise) in 12 steps. The effective crossover frequency between two loudspeakers is effected by gain. A lower filter frequency should be used when a higher gain is used on the subwoofer relative to the top cabinet.The low filter frequencies available on the SSP118 subwoofer are provided with the expectation that the gain of the subwoofer(s) will be higher than the gain of the top boxes and that the effective crossover frequency will be shifted upwards. This is intended to prevent the "boominess" that occurs with excessive output at overlapping frequencies.

4: DELAY

Provides delay adjustment from 0 ms to 2 ms.Use at 0 ms when tops are mounted directly above the subwoofer.When subs are ahead of the top, when the top is mounted far above the sub or when subs are located centered with the tops on the left and right, use the delay to compensate for the offset. Be sure to match the delay settings when boxes are adjacent to each other. Mismatched delay settings will cause a significant loss of energy.

The integrated DSP includes all the required processing for normal operation and alignment with the accompanying

BASSBOSS tops boxes.When connecting multiple BASSBOSS loudspeakers in a system,signal can be passed through from one powered loudspeaker to another using XLR cables. No processing is applied to the signal as it passes through from the input to the output connectors in each loudspeaker. Signal can be routed in any sequence because each loudspeaker receives a full-range signal and applies the necessary processing in order to operate as part of the overall system. It is recommended to run signal to the nearest box first and patch to the next nearest box in sequence.

No more than 2 powered SSP118 should be connected to a 20A circuit. The typical power draw of one SSP118 amplifier module is 5A. With heavy demand, the current draw can peak at 20A. It's recommended to power combinations of a subwoofer and a top on a circuit and to power each subwoofer and top combination on a separate circuit to reduce the chances of overdrawing a circuit and tripping a breaker.

Page 8

Thanks for your BASSBOSS purchase!

WARRANTY INFORMATION

Beyond ensuring your satisfaction, our extensive "Sound Defense" transferable warranty which covers all BASSBOSS products.

STANDARD CABINET WARRANTY

BASSBOSS loudspeaker cabinet integrity,including all joinery,fasteners,handles and wood,is warranted against defects in materials and workmanship for a period of six years from the date of purchase.This warranty does not cover items that are intended to wear and can be replaced if worn or damaged.Examples of items not covered by this warranty are cabinet feet, grills and the finish or coating applied to the cabinet.

ENHANCED COMPONENT WARRANTY

BASSBOSS self-powered loudspeaker amps and electronic components are covered against failures due to defects in materials and/or workmanship for a period of three years from the date of purchase. Speaker drivers and burned or open voice coils in subwoofers are covered for two years.

OUR SUPPORT

It is our goal to provide trouble-free loudspeakers.That objective begins as part of the design phase and continues on through to any service you may require.

In order to be able to provide the lowest possible failure rate, the best possible warranty service and the fastest turn-around time, we request that you contact us immediately if you notice any problem with your system, and before you attempt any repairs. We can provide the best and fastest solution if we know the details of the problem before any repair attempts are made. Often BASSBOSS technicians can troubleshoot problems that may arise and no repair or further service will be necessary.

Warranty support is a service,and part of that service includes helping you prevent failures and minimize repair and shipping costs.Please do not ship products without first obtaining a return authorization number by calling 512-368-3268 (855-822-7770 toll-free) or by emailing [email protected]. BASSBOSS service technicians will provide assistance and instructions on shipping and packaging requirements specific to your service needs.

WARRANTY LIMITATIONS

During the warranty period, if your loudspeaker malfunctions or fails due to any defect in components or manufacturing, the failed parts will be repaired or replaced.This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse. Warranty coverage will be determined upon inspection by BASSBOSS personnel. This warranty does not cover labor other than that authorized and performed by BASSBOSS personnel. Service will be performed upon the return of the failed unit, together with its original sales receipt or other proof of purchase, to BASSBOSS or an Authorized Service Facility.

Purchaser is responsible for all costs of shipping and handling. Cosmetic damage is specifically excluded from this warranty. This warranty is rendered void if service,repairs and/or modifications are attempted or made by anyone not specifically authorized by BASSBOSS to perform said services.Please contact BASSBOSS or your local BASSBOSS dealer before attempting any repairs and before shipping parts in for service.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. For more information concerning BASSBOSS service and warranty policies please contact us at 512-36-3268 or (855) 822-7770 toll-free.

EXPORT WARRANTY

BASSBOSS products can be purchased worldwide. In countries without local BASSBOSS distributors, product requiring service must be shipped back to the US for warranty repairs. In most cases, the entire cabinet will not need to be shipped. Generally only the individual affected parts will need to be shipped to the factory for servicing. Please contact BASSBOSS before attempting any repairs and before shipping parts in for service.

SHIPPING AND PACKAGING

Please package your returns safely and securely. BASSBOSS does not cover damage that occurs in transit. Freight insurance is recommended.

Page 9

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener- ates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

EC DECLARATION OF CONFORMITY

Manufacturer:

BASSBOSS 9501 Cargo Ave Ste 600 Austin TX 78719

We declare that under our sole responsibility the product: SSP118 Subwoofer

Intended use: Professional Audio Loudspeaker

Are in conformity with the provisions of the following EC Directives,including all amendments,and with national legislation implementing these directives:

• 2006/95/EC Low Voltage Directive

• 2004/108/EC Electromagnetic Compatibility Directive

• 2002/95/CE RoHs Directive

www.bassboss.com

©

®

2016 True Lee Loudspeakers, LLC – [email protected] – 512-368-3268 855-8-BASS-70 Toll Free

Page 10