Kicker SX650.1 Installation manual

SX .1 Series

Amplifier

Owners Manual

Mono-Block Models:

SX650.1 / SX1250.1

Attention:

Please take a moment and record the information asked for below in the provided area. It is also a good idea to attach the original sales receipt or a copy of it to this page for future reference

If for any reason you require service on this amplifier during the warranty period, you will need to provide this information and a copy of the receipt to Kicker to validate your warranty.

ALWAYS KEEP YOUR RECEIPT!

Congratulations!

You have just purchased the latest in amplifier technology to carry the famous KICKER name.

Your KICKER SX series amplifier employs the latest in DSP signal processing to give you total control over your sound. Like all KICKER products it is designed and built to give you years of powerful and trouble-free performance.

This installation manual contains valuable information on how to get the most out of your new SX series amplifier.

Thanks for buying KICKER. Enjoy!

Dealer Where Purchased:

_____________________________________________

Purchase Date:

Amplifier Model Number:

_____________________________________________

_____________________________________________

2

Amplifier Serial Number: _____________________________________________

SX .1 Series Amplifiers

Features

Low Impedance Operation Stable into 2 ohm

(SX650.1) or 1 ohm (SX1250.1) mono loads.

SORT Protection Circuitry (Short circuit, Over-voltage,

Reverse polarity, Thermal) Protects amplifier from accidents and out of spec operation.

MOSFET Power Supply Provides high efficiency operation.

PAST (Pre Amp Signal Transfer) Output RCA jacks to pass the incoming signal to another amplifier or component.

Class D High efficiency Class D design for maximum output power with minimal current draw.

Amp Strapping Allows you to combine two like models together for double the power at double the impedance!

Low Pass Filter Fully adjustable digital crossover with variable slope and crossover frequency. 30 Hz - 200 Hz in 1 Hz increments. OFF - 48 dB per octave slope in 6 dB increments.

High Pass Filter Fully adjustable digital crossover with variable slope and crossover frequency. 10 Hz - 60 Hz in 1 Hz increments. OFF - 24 dB per octave slope in 6 dB increments.

KickEQ Fully adjustable single band digital parametric equalizer with variable Q (bandwidth), variable center frequency and variable boost or cut. Q range .5 - 10 in .5 steps. Center frequency 20 Hz - 200 Hz in 1 Hz steps. Boost or cut range +/-

18 dB.

Adjustable Phase The output phase (polarity) can be set at 0 Degrees or 180 Degrees.

UltraMatch Gain Structure Digital input gain control with five selectable gain ranges (1 volt, 2 volt, 4 volt, 8 volt, 16 volt) with 12 dB of adjustment in each range in .5 dB steps.

SickBay and On Board Diagnostics Various tools to troubleshoot installation issues and check amp status.

Kompressor A 4-setting, user-selectable bass compressor used to fatten up your sub bass. OFF, RED-LINE, CONTOUR and

ATTACK with +/- 24 dB of adjustment to compensate for speaker size or listening style.

ISIS (pronounced eye-sis) ( I ndicate S tatus & I nput S ettings)

The user interface to view or adjust current settings and check the status of your Kicker SX amplifier.

BLAST Port ( Bass Level And Signal Transfer) Provides

Remote Bass Level Control and control signal transfer between multiple SX amplifiers.

EndKaps Cast aluminum, custom, removable covers to protect and hide all your wiring connections to the amplifier. Can be prepped and painted any custom color you choose.

SASA (S hake A S tick A t ) So many more features...it is more than you can Shake A Stick At. (It’s an Oklahoma thing!) Read on to find out!


3

4

ISIS

Meet the

ISIS

interface (Indicate Status & Input Settings).

The

ISIS

(pronounced eye-sis) allows you to view the current conditions and settings of your amplifier as well as change the many user-adjustable settings.The

ISIS

system consists of the VFD (Vacuum Fluorescent Display) and the nine soft touch buttons that make up the KEYPAD.

ISIS

VFD

ISIS

KEYPAD

VFD Display

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

* kicker

MEM-2 MEM-3 MEM-1

*

MEM-4

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

*

MEM-1

kicker

MEM-2 MEM-3

*

MEM-4

M1 M2 M3 M4

ESC HOME ENT

Here is a brief description of the indicators found on the

VFD.

AMP1 - Indicates amplifier 1 is selected for adjustment. Only available in four channel amps.

AMP2 - Indicates amplifier 2 is selected for adjustment.

Only available in four channel amps.

LOCK - Indicates the amplifier controls are locked out and not usable.

LEFT - Indicates an action or adjustment of the left channel.

SYS - Indicates you are in the system menu.

RIGHT - Indicates an action or adjustment of the right channel.

MUTE - Indicates you are in the mute menu or the mute function is active.


VFD DISPLAY - cont

GAIN - Indicates you are in the gain menu.

EQ

LPF

- Indicates you are in the equalizer menu.

- Indicates you are in the low pass filter menu.

HPF - Indicates you are in the high pass filter menu.

PHASE - Indicates you are in the phase menu.

KOMP

MEM-2

MEM-3

MEM-4

- Indicates you are in the Kompressor menu.

MEM-1 - Memory preset 1 activated.

- Memory preset 1 activated.



KEYPAD

The keypad consists of nine buttons that allow you to adjust your amplifier.

M1

M1 - Used to select memory preset 1 or to store current settings into preset 1.

M2


M3

M4



ESC ESC - Used to exit the current menu.

ENT - Used to enter the selected menu.

ENT

HOME

HOME - Used to return to the Main menu and other functions explained later.

UP - Used to advance up through menu selections and/or adjust amplifier controls.

DOWN - Used to advance down through menu selections and/or adjust amplifier controls.

These controls and their usage will be explained later with more detail in each menu usage section.


5

6

End Panel Views

The BLAST Port is used to connect the Remote Bass Level

Controller and for transferring control signals from one SX amplifier to another SX amplifier. An RJ45 cable is required to connect the BLAST Port (Out) of one amp to the BLAST Port

(In) of another. This is only required if you want to control more than one amplifier with the same Bass Level Controller.

More details on this further in the manual.

The speaker terminals are custom-machined connectors with full protective shrouds and are designed to accept heavy gauge speaker wire assures maximum power transfer and damping with minimal power loss.

Gold-plated RCA input connectors and PAST jacks provide solid input and output connections for your pre-amp signal.

BLAST Port In BLAST Port Out

Custom-machined power block accepts up to a 2 Ga wire for both power and ground connections and up to an 8 Ga for remote turn-on assures maximum power transfer with minimal loss.

On-board fusing (number of fuses vary by amp size) to protect amplifier against over current conditions and reverse polarity.

Power LED indicates amplifier is powered up and operating.

Check Fuse LED indicates a fault with the end panel fuses.

This could be fuses which are not seated properly, faulty fuses or blown fuses.

NOTE...

SX1250.1 does not have on-board fusing or the Check Fuse

LED due to larger external fusing requirements.

Power LED

Check Fuse LED

Fusing

XX XX

Speaker +

Speaker -

Left PAST

Right PAST

Right Input

Left Input

Ground

Remote

+ 12 Volt


Mounting

Remove Remove

When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the area that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc.

All amplifiers generate heat under normal operation. Be sure to choose a location that allows adequate ventilation for the amplifier. Also consider that the air temperature inside an automobile’s trunk can reach upwards of 140 degrees fahrenheit. An amplifier mounted in the trunk may require additional cooling such as extra fans moving air around the amplifier’s chassis or ventilating the trunk to exchange the hot air in the trunk for cooler air outside. If possible, mounting the amp in the passenger compartment will allow cooler operation.

Remember that the controls on top of the amp will need to be accessible for adjustment later. Keep this in mind as you choose your amplifier’s mounting location.

Now that you are ready to mount your amplifier, use the supplied 3mm allen wrench to remove the amplifier EndKaps.

This will give you access to the mounting holes in the amplifier and all wiring connections.

See Fig. 1

Remove

Fig. 1

R

R

LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

KOMP

* kicker


*

MEM-4

M1 M2 M3 M4

ESC HOME ENT

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

*

MEM-1 MEM-3

AMP2

MUTE

KOMP

Remove

With the EndKaps removed, you now have access to the four mounting holes in the mounting feet and all wiring connections. Drill 4 holes using a 7/64” drill bit and use the supplied

#

8 screws to mount the amplifier.

See Fig. 2

M1 M2 M3 M4

ESC HOME ENT

Fig. 2


7

Wiring

Signal is input into the amplifier using the low level RCA input connections. If your source unit does not have RCA output connectors you will need to use a Hi-Lo level signal adapter. See your Kicker dealer for more details on this.

The output (PAST) RCA jacks provide an unaltered signal output to feed another amplifier or component.

SOURCE UNIT

The ground should be connected to the amplifier first before making any of the other connections. This wire should be as short as possible (24 inches or less) and connected to a paint/corrosion free solid metal area of the car’s chassis. Use the same gauge wire as recommended for the amplifier’s power connection to the battery. Adding an additional ground wire between the car battery’s negative post and the car chassis of this same gauge (or larger) is also recommended.

If you ever need to remove the amp from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifier, just the opposite of when you installed it.

A fuse must be installed within 18 inches of the battery to protect the power wire feeding your amplifier. This fuse should be of at least the same value used in the amplifier but no higher than the capacity of the power wire. See the charts below for wire size and fusing recommendations.

Model Fuse Size Wire Size

SX650.1

SX1250.1

60A

150A

4 GA

2 GA

8

The use of twisted pair interconnects is recommended for all installations to minimize noise. When routing these cables through the automobile, try to keep them away from factory wiring harnesses and other power wiring. If you need to cross any of this wiring do so at a 90 degree angle to reduce the possibility for noise problems.

When working with power connections it is always recommended that you disconnect the battery to prevent accidents.

Wire Size Length Maximum Fuse

8 Ga

4Ga

2 Ga

0Ga

8 Ga

4 Ga

2 Ga

0 Ga

Less than

10 feet in length

10 feet to

20 feet in length

70 Amps

175 Amps

250 Amps

400 Amps

40 Amps

90 Amps

150 Amps

200 Amps


System Diagrams

SINGLE SPEAKER OR VOICE COIL

SX.1 series amplifiers are capable of operating into a minimum impedance of 2 ohms

(SX650.1) or 1 ohm (SX1250.1).

GROUND

SIGNAL IN

SIGNAL OUT _

+12V

BATTERY

FUSE

8

AMP 1 AMP 2

GAIN EQ LPF HPF PHASE KOMP

8 8 8 8 8 8 8 8 8

M1 M2 M3 M4

ESC HOME ENT

S -

S+

+

MULTIPLE SPEAKERS OR VOICE COILS PARALLEL WIRED

SX.1 series amplifiers are capable of powering multiple speakers or voice coils wired in parallel as long as the minimum impedance does not drop below 2 ohms (SX650.1) or 1 ohm (SX1250.1).

GROUND

SIGNAL IN

SIGNAL OUT _ _ _ _

+12V

BATTERY

FUSE

8

AMP 1 AMP 2


8 8 8 8 8 8 8 8 8

M1 M2 M3 M4

ESC HOME

ENT

S -

S+


+ + + +

9

10

MULTIPLE SPEAKERS OR VOICE COILS SERIES WIRED

SX.1 series amplifiers are capable of powering multiple speakers or voice coils wired in series as long as the minimum impedance does not drop below 2 ohms (SX650.1) or 1 ohm

(SX1250.1).

GROUND

SIGNAL IN

SIGNAL OUT _ _

+12V

BATTERY

FUSE

AMP 1 AMP 2


8 8 8 8 8 8 8 8 8 8

M1 M2 M3 M4

ESC HOME ENT

S -

S+

+ +

These are just a few of the many ways you can use your SX.1 series Kicker amplifier.

These system diagrams are designed to give you a basic understanding of the most common uses for this amplifier. For more complex systems please visit your local authorized

Kicker dealer. You can also download the SX Technical Manual from our website at www.kicker.com for more detailed information and complex system diagrams.

_

+


AMPLIFIER STRAPPING

SX.1 series amplifiers are capable of being strapped together to provide twice the power into twice their rated minimum impedance. Only like model amps can be strapped together. In other words, the SX650.1 can only be strapped to another SX650.1 and the SX1250.1 can only be strapped to another SX1250.1.

NOTE...

4 ohm minimum impedance for SX650.1 when strapped.

2 ohm minimum impedance for SX1250.1 when strapped.

1.) Wire both amplifiers to 12 volt power, ground and remote.

2.) Connect a RCA cable from the source unit to the RCA

Input jacks on the primary amp.

3.) Use the supplied 1/8 inch mono cable to connect the

Amp Strapping Out jack of the primary amplifier to the

Amp Strapping In jack of the secondary amplifier.

4.) Use a short piece of heavy gauge wire (12Ga, 10Ga, 8Ga) to connect the Speaker negative terminals of both amps together.

5.) The primary amplifier’s positive terminal is used for the positive speaker connections.

6.) The secondary amplifier’s positive terminal is used for the negative speaker connections.


AMP STRAPPING

AMP STRAPPING

_

+

SOURCE UNIT

11

12

AMPLIFIER STRAPPING WITH REMOTE BASS CONTROL

The Remote Bass Level Controller can be used to adjust the output level of both the amplifiers that are strapped together.

1.) Mount the Remote Bass Level Controller in the front of your vehicle and plug in the supplied cable.

2.) Route the supplied cable to the primary amplifier and connect to its BLAST In jack.

3.) Enjoy!

SUPPLIED

CABLE

BACK VIEW

SIDE VIEW

Mounting Surface

SOURCE UNIT

AMP STRAPPING


AMP STRAPPING

_

+

USING THE SIGNAL OUTPUT JACKS (PAST)

The Output (Pre Amp Signal Transfer) RCA jacks allow you to send the incoming signal from one Kicker SX series amplifier to another amplifier or processor without the need for Y cables. The signal from the PAST jacks is identical to the signal fed to the amplifier via its RCA input jacks and is not affected by any of the amplifier’s built-in digital signal processing.

Most head units with high voltage outputs should be capable of driving up to ten amplifiers in a chain.

AMP STRAPPING

SOURCE UNIT

AMP STRAPPING


To Next Amplifier or Processor

13

14

USING THE REMOTE BASS LEVEL CONTROL & BLAST

You can use the Remote Bass Level Control to control the output of your amplifier from the front of the car.

Mount the controller by simply screwing the metal bracket to the chosen location and then slide the housing onto the bracket until it snaps into place.

Route the cable from the controller to the BLAST input jack on the amplifier chassis. That’s it.

If you wish to control more than one amplifier with your remote, you will simply need to use a RJ45 cable (not supplied but available at any Radio Shack, computer store or electronics center) to connect the BLAST output jack of the first amp to the BLAST input jack of the next amplifier.

SUPPLIED

CABLE

BACK VIEW

SIDE VIEW

Mounting Surface

AMP STRAPPING

SOURCE UNIT

OPTIONAL

RJ45 CABLE

AMP STRAPPING


OPTIONAL

RJ45 CABLE

To Next Amplifier

Navigation

Your KICKER SX series amplifier uses the latest in Digital DSP control and provides you with valuable operational information about your amplifier, real-time diagnostics and a full multi-level menu-driven operating system to access and adjust your amplifier.

As you can see there can be an infinite number of menu levels and each one of these menu levels can have an infinite number of its own items.

Navigating this simple menu structure is very easy using the 5-way keypad.

ESC HOME ENT

The menu system is designed in layers. There is a starting point and you keep drilling down until you get to the menu item you want to view or change. This menu tree is an example of how the SX menu structure is set up.

You use the UP and DOWN available menu items, and the keys to scroll through the

ENT key is used to select that menu item. The ESC key backs you up one menu level from where you are, and the HOME key can return you all the way to MAIN MENU by pressing and holding it for 1.5 seconds.

NOTE: Not all the menus and menu items are shown below.

DEFAULT

SCREEN

MAIN MENU

* SYSTEM

GAIN

EQ

LO-PASS

HI-PASS

∝

SYSTEM MENU

VOLT NOW

VOLT MIN

VOLT MAX

TEMP NOW

TEMP MAX

RUN TIME

SICK BAY

∝

For example let’s begin at the DEFAULT SCREEN; our goal is to get to the HISTORY menu. Pressing the ENT key would get us to MAIN MENU. Now use the UP and

DOWN keys to scroll to SYSTEM, and then press the ENT key. Now you are in the SYSTEM MENU. Using the UP and

DOWN keys again you scroll to SICK

BAY and press the ENT key. You are

ESC HOME ENT

ESC HOME ENT now in the SICK

BAY MENU. Use the UP and DOWN keys again to scroll to HISTORY and then press the ENT key. That’s it! You are there.

SICK BAY MENU

This is how you view information and change settings in your KICKER SX amplifier.

CURRENT

HISTORY

∝ ∝


15

16

Continuing our example, we are now in the HISTORY item in the SICK BAY MENU. If we press the

ESC key we would go back up to the

SICK BAY MENU. If we press the ESC key again we would go to the SYSTEM

MENU. One more press of the ESC key and we are in the MAIN MENU.

ESC HOME ENT

Let’s start at the HISTORY item in the SICK BAY MENU again but instead press and hold the HOME key for 1.5 seconds. Doing this will take us all the way back to the MAIN

PRESS &

HOLD

MENU in one key press. Pressing and holding the HOME key will return you all the way back to the MENU ITEM you

ESC HOME ENT started with in the MAIN MENU, no matter how deep in the menu level structure you are. Pretty cool!

This is a very quick way to return to the MAIN MENU after drilling down several menu layers to view or change an item.

Pressing the key and holding it in for longer than 1.5 seconds will activate the accelerated scrolling mode and scroll through the menu items at a much faster rate. Releasing the key will return it to normal speed mode.

ESC

PRESS &

HOME

HOLD

ENT it!

Don’t try to scroll through every 1/12 octave step without

When adjusting any amplifier control the UP and arrow keys have 2 speeds, normal and accelerated.

DOWN

Pressing and releasing the key repeatedly will scroll through the menu items at normal speed.

PRESS &

RELEASE

ESC HOME ENT


Menu System

The menu system layout is as follows:

DEFAULT - This menu is displayed when your amp is operating and no adjustments are being made to your amplifier. This information scrolls through the display one after the other and then repeats.

1.)

KICKER

- Hey, we needed a brand plug for us since this amp is sooooo cool!

2.)

XX.X Volts

- Displays the current voltage at the amplifier’s + 12 volt battery input terminal.

3.)

XX.X DEG f

or

xx.x DEG c

- Displays the current temperature of the amplifier in celsius or fahrenheit.

4.)

amp name

- Model name of the amplifier or the name you have changed it to.

5.)

memory name

- Current memory preset in use (if any) or the name you have changed it to.

ESC HOME ENT

If you want to freeze the scrolling display simply press the HOME key and the scrolling will stop.

Now you can manually select the item you wish to have displayed by using the

UP or DOWN keys. ESC HOME ENT

If you want the display to continue scrolling simply press the HOME key again.

MAIN - This menu is the first menu accessed from the

DEFAULT menu and is the gateway to all the settings and information on your SX series amplifier.

To enter the MAIN menu simply press the ENT menu.

key while in the DEFAULT

ESC HOME ENT

The available selections in the MAIN menu are:

System

GAIN

EQ

Lo-Pass

Hi-Pass

Phase

Mute

Kompressor

Security

Use the UP and DOWN arrow keys to scroll through the available selections in the MAIN menu.

ESC

When you have the menu item selected that you want to view or adjust simply press the ENT key to select it.


ESC

HOME

HOME

ENT

ENT

17

18

SYSTEM

MENU - This menu item contains many diagnostic tools and first time setup options. Use the UP and DOWN arrow keys to scroll through the options and press select. Press the

ENT to

ESC key to return to the SYSTEM menu.

1.)

Volt Now

- Displays the current voltage at the amplifiers +12 volt terminal.

2.)

Volt Min

- Displays the lowest voltage seen at the amplifiers +12 volt terminal since being installed.

3.)

Volt Max

- Displays the highest voltage at the amplifiers +12 volt terminal since being installed.

4.)

Temp Now

the amplifier.

- Displays the current temperature of

5.)

Temp Max

- Displays the highest temperature the amplifier has reached since being installed.

6.)

Run Time

- Displays the total time the amplifier has been powered up since installation in 1/10th of an hour increments

7.)

Sick Bay

- Contains several diagnostic tools. Once in this menu you use the UP scroll through and DOWN

CURRENT

, keys to

HISTORY

and

PINK NOISE

options. Press the ENT key to select.

ESC HOME ENT

7a.)

CURRENT

shows amplifiers current status or fault code. The 6 possible codes are:

normal

- No problem, normal operation.

thermal

- Thermal cutoff protection engaged.

short

- Short circuit protection engaged.

Hi-Volt

- High voltage protection engaged.

FUSE

- Faulty or blown power fuse.

SERVICE

- Amp requires service by KICKER.

When you are done viewing the current status press the

ESC key to return to the SICK

BAY menu.

7b. )

HISTORY

logs the last 5 fault codes and how long ago they happened when compared to the RUN TIME log.

Use the UP and keys to select the

DOWN

HISTORY

log entry you want to view.

ESC

ESC

HOME

HOME

ENT

ENT

Press and hold the ENT key to view the time it happened.

ESC HOME ENT

When you are done viewing the history press the ESC key.

ESC HOME ENT


SICK BAY - cont

7c.)

PINK NOISE

is a built in pink noise generator to test operation of the amplifier

Use the UP and DOWN keys to select

NOISE ON

or

NOISE OFf

.

ESC HOME ENT

When the PINK NOISE is ON the

LEFT

and

RIGHT

indicators in the ISIS VFD will blink on and off.

LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

KOMP

noise on

MEM-2 MEM-3 MEM-1 MEM-4

8.)

Amp Name

- Here you can assign a unique name to your KICKER SX amplifier. This name will replace the model name in the DEFAULT screen. If you change your mind and do not want to change the name, press and hold the

HOME key for 1.5 seconds BEFORE making any changes.

The ESC and ENT keys move the cursor left or right to select which character to change. ESC HOME ENT

When you are done using the

PINK NOISE generator press the

ESC key to return to the SICK

BAY menu.

ESC HOME ENT

NOTE...

If you exit the SICK BAY menu with the PINK NOISE generator still on, the

LEFT

and blinking as a reminder.

RIGHT

ISIS VFD indicators will remain

Use the UP and DOWN keys to change the character displayed

(A, B, C...1, 2, 3...etc)

When you are finished press and hold the HOME key for 1.5 seconds to save your new amplifier name.

ESC HOME ENT

PRESS &

HOLD

ESC HOME ENT


19

20

9.)

Mem Name

- Here you can change the names of the memory locations. The factory defaults are

Memory-1

Memory-2

Memory-3

Memory-4

ESC HOME ENT

Use the UP and DOWN keys to select the memory location name you want to change and then press the

ENT key to select it.If you change your mind and do not want to change the name, press and hold the HOME key for 1.5 seconds BEFORE making any changes.

ESC HOME ENT

The ESC and ENT keys move the cursor left or right to select which character to change.

ESC

ESC

HOME ENT


(A, B, C...1, 2, 3...etc)

PRESS &

HOLD

HOME ENT

When you are finished press and hold the HOME key for 1.5 seconds to save your new memory name.

10.)

Remote Adr

- This feature is currently not used but is reserved for future expansion.

11.)

Gain Range

- Sets the input voltage window of the

UltraMatch gain control. Possible choices are:

1V, 2V, 4V, 8V, 16V

Select the one closest to the maximum RCA input voltage you expect to send to the amplifier.

Use the UP and DOWN keys to select your voltage. Press the ESC to return to the MAIN menu.

ESC HOME

12.)

Bypass DSP

- Bypasses all DSP processing and sends the input signal directly to the amplifier.

ENT

Use the select

UP and DOWN keys to

BYPASS ON

or

BYPASS OFF

.

Press the ESC the MAIN menu.

key to return to

ESC HOME ENT

13.)

Komp Adj.

- This adjusts the KOMPRESSOR activation threshold. Range is +24 dB to -24 dB to allow for different sized speakers or listener tastes. 0 is the default factory setting.

ESC HOME ENT

Use the UP and DOWN keys to select your setting and then press the

ESC to return to the MAIN menu.

Repeat the above steps to rename the other presets.


14.)

Display

- Several options to allow customizing the amplifier’s VFD display.

14a.)

BRIGHTNESS

- Adjust the intensity level of the ISIS VFD display. Five selectable levels.

MINIMUM

- dimmest setting.

LOW

MEDIUM

HIGH

MAXIMUM

- brightest setting.

14b.)

TEMP C/F

- Selects between Celsius (

CELSIUS

) or Fahrenheit ( readouts.

FAHRENHEIT

) for temperature

14c.)

HOLD TIME

- Adjusts the speed of the scroll in the Default Screen display. Determines how long each menu item stays in the display before scrolling to the next item. Adjustable from 1 - 11 seconds.

14d.)

SCRNSAVER

- Option to turn on or off the screensaver. When on (

AUTO

) the display will go to sleep when there is no button activity for 60 seconds.

Pressing any button once will wake up the display.

The

OFF

selection turns off the screensaver and the display is always on.

15.)

Lock Code

default is

- Set your own lock code! The factory

123

but you can change it and create your own code with up to 10 characters.

The ESC and ENT keys move the cursor left or right to select which character to change.

ESC HOME

ESC HOME ENT


(

A, B, C...1, 2, 3...etc)

ENT

When you are finished press and hold the HOME key for 1.5 seconds to save your new amplifier lock code.

IMPORTANT!!! Be sure to write this code down for future reference.

ESC

PRESS &

HOLD

HOME ENT


21

22

16.)

Reset Amp

- This option resets all adjustable settings back to their original factory defaults.

Use the select

UP and DOWN keys to

SKIP RESET

or

DO RESET

and then press the ENT the selected action. key to perform

ESC HOME ENT

Gain

MENU - Here is where you adjust your amplifier’s gain control settings.

Press the ENT key to enter the GAIN adjustment menu.

ESC HOME ENT

17.)

About

- This menu item will display information about the DAP (Digital Audio Processor) hardware, software and build date.

ESC HOME ENT

Use the UP and DOWN keys to view the DSP Version, Software Version,

Hardware Version and Build Date. Press the ESC key to return to the MAIN menu.

Now use the UP and DOWN keys to increase or decrease the gain of the amplifier in .5 dB increments from

0 dB to +12 dB. (

.0

to

12.0

) ESC HOME ENT

Press the ESC key to return to the

MAIN menu when finished adjusting the gain control.

ESC HOME ENT

NOTE...

While adjusting the GAIN you will notice the

gain

indicator on the ISIS VFD display is lit. This indicates you are in the

GAIN menu.


EQ

MENU - Here you can adjust the single band parametric equalizer. Your options are

frequency

,

bandwidth

and

boost/cut

.

Press the ENT adjustment menu.

key to enter the EQ

Use the UP scroll through and DOWN

frequency

, keys to

bandwidth

and

boost/cut

key to select.

and press the ENT

ESC

ESC

HOME ENT

HOME ENT

FREQUENCY

selects the center frequency of the EQ and can be set at any 1 Hz spaced frequency from

20 Hz

-

200 Hz

.

Use the UP and DOWN keys to select your frequency. Press the

ESC to return to the EQ menu.

ESC HOME ENT

BOOST/CUT

is how much you want to boost or cut the equalizer and has a range of

-18 dB

to

+ 18 dB

in .5 dB steps.

Use the UP and DOWN keys to boost or cut the EQ and then press the ESC menu.

key to return to the EQ ESC HOME ENT

When you are done adjusting the

EQ press the

EQ

frequency

ESC key while in the

,

bandwidth

and

boost/cut

option menu to return to the MAIN menu.

ESC HOME ENT

NOTE...

While adjusting the EQ you will notice the menu.

EQ

indicator on the ISIS VFD display is lit. This indicates you are in the EQ

BANDWIDTH

(better known as Q) can be set from

.5

to

10

in

.5 increments. In simple terms, lower Q effects more frequencies around the center frequency while higher Q effects fewer frequencies around the center frequency.

Use the UP and DOWN keys to select your Q value. Press the to return to the EQ menu.

ESC

ESC HOME ENT


23

Lo-Pass

MENU - Here is where you adjust the low pass crossover. Your options are

frequency

and

SLOPE

.

Press the ENT key to enter the

LO-PASS adjustment menu.

ESC HOME ENT

The KICKER SX amplifier monitors and prevents any low pass crossover point from being any closer than 1/3 octave from the high pass crossover point. If you cannot set the low pass crossover where you want then check the

HPF

indicator and see if it is flashing. If it is then you need to go to the HI-PASS menu and raise the high pass crossover point.

This is done as a safety precaution to prevent a notch filter condition.


frequency

keys to and

SLOPE

and press the ENT key to select.

ESC HOME ENT

24

FREQUENCY

selects the crossover point and can be set at any

1 Hz spaced frequency from

30 Hz

to

200 Hz

.

Use the UP and DOWN keys to select your frequency. Press the

ESC to return to the LO-PASS menu.

ESC HOME ENT

SLOPE

selects the rolloff of the crossover and can be set from

oFF

to

48 dB

in 6 dB steps.

Use the UP and DOWN keys to select your slope. Press the ESC to return to the LO-PASS menu.

ESC HOME ENT

NOTE...

While adjusting the low pass crossover you will notice the

LPF

indicator on the ISIS VFD display is lit. This indicates you are in the LO-PASS crossover menu.


hi-pass

MENU - Here is where you adjust the high pass crossover. Your options are

frequency

and

SLOPE

.


LO-PASS adjustment menu.

ESC HOME ENT


frequency

keys to and

SLOPE


ESC HOME ENT

FREQUENCY

selects the crossover point and can be set at any

1 Hz spaced frequency from

10 Hz

to

60 H

z.

Use the UP and DOWN keys to select your frequency. Press the ESC key to return to the HI-PASS menu.

ESC HOME ENT

The KICKER SX amplifier monitors and prevents any high pass crossover point from being any closer than 1/3 octave from the low pass crossover point. If you cannot set the high pass crossover where you want then check the

LPF

indicator and see if it is flashing. If it is then you need to go to the

LO-PASS menu and lower the low pass crossover point.

This is done as a safety precaution to prevent a notch filter condition.

SLOPE

selects the rolloff of the crossover and can be set from

OFF

to

24 dB

in 6 dB steps.

Use the UP and DOWN keys to select your slope. Press the ESC to return to the HI-PASS menu.

ESC HOME

NOTE...

While adjusting the high pass crossover you will notice the

hpf

indicator on the ISIS VFD display is lit. This indicates you are in the HI-PASS crossover menu.

ENT


25

26

Phase

MENU - Here you can switch the polarity of the amplifier’s output between 0 or 180 degrees. Your options are

0 degree

and

180 degree.


PHASE adjustment menu.

ESC HOME ENT

7.)

Mute

- Here you can mute the amplifier’s output for setup or testing purposes. Your options are

MUTE ON

and

MUTE OFF.


MUTE adjustment menu.

ESC HOME ENT


0 degree

keys to and

180 degree


ESC HOME ENT

Use the UP and DOWN keys to scroll through

MUTE ON

and

MUTE OFF.

ESC HOME ENT

Press the ESC key to make your selection and return to the

MAIN menu.

ESC HOME ENT

NOTE...

While adjusting the PHASE you will notice the are in the PHASE menu.

PHASE

indicator on the ISIS VFD display is lit. This indicates you

Press the ESC key to make your selection and return to the

MAIN menu.

ESC HOME ENT

NOTE...

While adjusting the MUTE you will notice the

mute

indicator on the ISIS VFD display is lit. This indicates you are in the MUTE menu.

If you exit the MUTE menu with the muting activated, the

MUTE

indicator will flash to indicate this.


Kompressor

MENU - Here you can select which Kompressor setting you wish to use. The SX amplifier utilizes a full digital compressor circuit to tweak the amplifier and the sound to your unique needs. Your options are

RED-LINE

,

CONTOUR

,

ATTACK

, and

OFF

.


KOMPRESSOR adjustment menu.

ESC HOME ENT

Once in this menu use the UP and

DOWN keys to scroll through

RED-LINE

,

contour

,

attack

and

OFF

.

ESC HOME ENT

Press the ESC key to accept your selection and return to the MAIN menu.

ESC HOME ENT

NOTE...

While adjusting the Kompressor you will notice the are in the KOMPRESSOR menu.

KOMP

indicator on the ISIS VFD display is lit. This indicates you

See the specifications pages for a brief description of each

Kompressor setting and some general guidelines for their use.


27

Security

MENU - Here you can lock down your amplifier to prevent any access to the settings. The DEFAULT screen is still active and you can select any of the four presets... but that is it!


SECURITY menu.

ESC HOME ENT

UNLOCK AMPLIFIER

You do remember your lock code right? You better because that is now the only way in! If you have not changed it then it is still at the factory default of

123

.

2 Times

To unlock your amplifier press the

ENT key. The display will show

UNLOCK

. Press the ENT key again.

You will now enter your code to unlock the amplifier.

ESC HOME ENT

Use the UP and DOWN keys to select

LOCK IT UP

and then press the or

DON’T LOCK

ENT key to accept your setting.

ESC HOME ENT

If you selected

LOCK IT UP

the display will now show

UNLOCK

and the LOCK indicator will be on . The menus are now locked.Press the ESC key to return to the

DEFAULT scrolling screen.

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

unlock


If you selected

DON’T LOCK

then you will return to the

MAIN menu and the amplifier will remain unlocked.

The ESC and ENT keys move the blinking cursor left or right to select which character to enter.

Use the UP and DOWN keys to

( enter the character.

A

,

B

,

C

...

1

,

2

,

3

...etc)

ESC

ESC

HOME

HOME

ENT

ENT

28

NOTE...

While your amplifier is in lock down you will notice the

LOCK

indicator on the ISIS VFD display is lit. This indicates your amplifier is locked down and will require a code to unlock it before any adjustments can be made.

When you are finished press and hold the HOME key for 1.5 seconds to enter your unlock code.

ESC HOME ENT

If the code is correct the amp will unlock and drop you back into the MAIN menu. If not, then read on...


UNLOCK AMPLIFIER - cont.

If you enter the wrong code the display will flash the message

BAD CODE

and then return you to

UNLOCK

screen.

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

bad code


AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

unlock


You will need to call KICKER directly at (405) 624-8583 to handle this situation. You will need your amplifier’s serial number AND your receipt as the guys and gals answering the phone will need this information from you to help you out.

So...before you call, gather this information up and have it ready to save us some time on the phone. Cool? Cool!

Better yet, take the time RIGHT NOW to fill out the first page in this manual and STAPLE your receipt to it. That way if or when you need service (like forgetting your lock code) you will have all the information you need right there in front of you.

Press the ENT key to enter your lock your code again.

ESC HOME ENT

Enter your code again making sure to place the correct character in the correct position in the display. Blank spaces count as part of the code so be sure you are entering it correctly.

Press and hold the HOME key and try again. If you have found your error then the amp will unlock. If not, the flashing

BAD CODE

will greet you and you can try again.

If you have tried several times (several is defined as more than 3...less than 10) and you still can not unlock your amplifier, this more than likely means means you have forgotten your lock code.


29

30

Memory Presets

There are four memory preset keys each with an indicator above it in the ISIS VFD display. The indicator will illuminate if that memory preset is currently in use.

Each preset stores all the values for each of the following amplifier controls:

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

*

MEM-1

kicker

MEM-2 MEM-3

*

MEM-4

INDICATORS PRESETS

*.)

*.)

*.)

*.)

*.)

*.)

*.)

GAIN

EQ

LO-PASS

HI-PASS

PHASE

MUTE

KOMPRESSOR

M1 M2 M3 M4

ESC HOME ENT

This gives you the ability to dial in four completely different amplifier settings and store them in presets for instant recall later.

It’s like a preset for your favorite radio stations...only better!

STORING A PRESET

Make all the adjustments you want to have stored in the preset and return to the DEFAULT screen.

To store your settings into a preset simply press and hold the desired memory key until the VFD display flashes

STORED

. Then release the memory key.

The indicator which matches the preset you used will illuminate.

M1 M2

HOLD

M3 M4

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

RIGHT

PHASE

AMP2

MUTE

KOMP

stored


RECALLING A PRESET

To recall a memory preset simply press and release the key. The matching indicator will light up and the amplifier will change all the corresponding controls to the values assigned to the memory preset.

PRESS &

RELEASE

M1 M2

AMP1

LOCK LEFT SYS

GAIN EQ LPF HPF

M3

RIGHT

PHASE

M4

AMP2

MUTE

KOMP

* kicker


*

MEM-4


PRESET PRESETS

Ok, we know that sounds like a certain pizza commercial, but seriously the four memory presets come with settings already in them.

You can use these as a starting point to do your own tweaking or for quick push-a-button-and-be-done setup.

Any preset you store will replace the ones that come from the factory. You can reset all four preset back to factory defaults anytime simply by doing a reset in the RESET AMP menu.

Here are the settings in each preset from the factory.

MEMORY-1 MEMORY-2 MEMORY-3 MEMORY-4

GAIN LEVEL 6 DB

EQ FREQUENCY 40 HZ

EQ BOOST/CUT FLAT

EQ BANDWIDTH 3

LO-PASS SLOPE 24 dB

LO-PASS FREQ 80 HZ

HI-PASS SLOPE 24 DB

6 DB

40 HZ

+ 6 DB

3

24 DB

80 HZ

24 DB

6 DB

40 HZ

+ 6 DB

3

24 DB

80 HZ

24 DB

6 DB

40 HZ

+ 6 DB

3

24 DB

80 HZ

24 DB

HI-PASS FREQ 25 HZ 25 HZ 25 HZ 25 HZ

PHASE L&R CH.

0 DEGREE 0 DEGREE O DEGREE O DEGREE

MUTE L&R CH.

KOMPRESSOR

KOMP ADJ.

OFF

OFF

0 DB

OFF

OFF

0 DB

OFF OFF

CONTOUR RED-LINE

0 DB 0 DB

In more general terms, each preset offers you these options.

Memory-1 sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz and an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies.

Memory-2 sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies and a 6 dB bass boost at 40 Hz.

Memory-3 sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies, a 6 dB bass boost at 40 Hz and sets the

Kompressor into CONTOUR mode.

Memory-4 sets the amplifier up with a 24 dB per octave low-pass crossover at 80 Hz, an infrasonic filter (often called subsonic filter) to protect the speakers from harmful ultra-low frequencies, a 6 dB bass boost at 40 Hz and sets the

Kompressor into RED-LINE mode.

As stated before you can always start with one of these presets, tweak it to fit your installation and then save your settings into a new preset.


31

Troubleshooting

If your amplifier does not appear to be working, check obvious things first such as blown fuses, poor or incorrect wiring connections, crossovers set improperly, gain controls improperly set, etc.

¬

Substitute known good source unit.

;

If amp does not make noise using PINK NOISE then:

¬

Check speaker connections.

¬

Test speaker outputs with known good speaker.

32

There are two LEDs on the end panel of your KICKER SX series amplifier, one green and one red. The green LED indicates the amplifier is turned on. The red LED indicates that there is a fault condition with the end panel fuses and they need checked.

The power indicator on top of the amplifier which illuminates the model badge follows the same function as the green LED.

Green LLED o

¬

With a Volt Ohm Meter (VOM) check:

¬

+ 12 volt power terminal (should read +12V to +16V).

¬

Remote turn-on terminal (should read +12V to +16V).

¬

Ground terminal to chassis ground (should read 0).

Green LLED o

¬

Check amp status in SICK BAY.

¬

Check GAIN RANGE in SYSTEM menu.

¬

Check GAIN LEVEL in GAIN menu.

¬

Check if MUTE is activated.

¬

Test amp using PINK NOISE in SICK BAY menu.

;

If amp makes noise using PINK NOISE then:

¬

Check RCA cable and connections.

¬

Check for signal on RCA cable with VOM in AC position.

Other SSymptoms:

;

Amp is very hot, no output.

¬

Thermal protection is engaged. Check SICK BAY to verify. Check for proper impedance at speaker terminals. Also check for adequate airflow around amplifier.

;

Amp shuts down while vehicle is running.

¬

Over Voltage protection engaged. Check SICK BAY to verify. Voltage to the amplifier is not within the

9-16 volt operating range. Have automobile charging/electrical system inspected.

;

Amp only plays at low volume levels.

¬

Short circuit protection engaged. Check SICK BAY to verify. Check for speaker wires shorted to each other or the vehicle chassis. Damaged speakers or operating amplifier below minimum recommended impedance will also cause this.

;

Weak bass output.

¬

Change the phase of the LEFT channel in the PHASE menu. If bass improves then one speaker channel is out of phase (polarity). You can leave PHASE changed for this channel to fix the problem or better yet;

Check speaker connections to amp and speakers to determine which one is wrong and correct. Be sure to set the PHASE of the LEFT channel back to original setting after correcting wiring connections.


Alternator n (whining sound that varies with engine RPM):

¬

Check for damaged RCA cables.

¬

Check routing of RCA cable.

¬

Check source unit for good ground.

¬

Check GAIN RANGE in SYSTEM menu, turn down if set too high.

¬

Check GAIN in MAIN MENU, turn down if set too high.

CAUTION: When jump-starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections (+ to - & - to +) will result in blown amplifier fuses as well as failure to other systems in the vehicle.

If you have more questions about the installation and operation of your new KICKER amplifier, see the Authorized KICKER

Dealer in your area. You may also call our Technical Services

Line at (405)624-8583 for assistance or visit our website at www.KICKER.com


33

34

Kompressor

Here is a brief explanation of each KOMPRESSOR setting.

Contour

- This preset applies expansion below the threshold point to provide a fuller sound at lower volume levels. Effect decreases at higher volume levels. Nice effect for someone wanting a fuller sound at low to moderate listening levels.

ATTACK

- This preset applies expansion above the threshold point to provide a nice quick punch or attack to the music.

Effect increase with higher volume levels. Like music with a quick and punchy sound? Give this one a try.

Red-line

- Provides a quick clamp to dynamic peaks while still allowing a full sound to come through. Effect increases at higher volume levels. Like to play it loud but want to protect your speakers? Want low level details to come through over road noise? Want a more even volume level to your music? All can be achieved with this preset.

OFF

- Pretty much says it all. This turns the KOMPRESSOR off. This is the factory default setting.

After selecting your KOMPRESSOR setting you can adjust its effect using the KOMPRESSOR ADJUSTMENT (

KOMP ADJ.

) setting located in the SYSTEM menu. There you can change the threshold point for each of these settings to customize the KOMPRESSOR effect to fit your speakers, car or personal tastes.

The possibilities are almost endless! Tweak away!


Performance

Model SX650.1

RMS Power

In Watts, All Channels Driven

@ 13.8V, 4Ω Mono, 1.5% THD

@ 13.8V, 2Ω Mono, 1.5% THD

@ 13.8V, 1Ω Mono, 1.5% THD

Dynamic Power

In Watts, All Channels Driven

@ 14.4V, 4Ω Mono, 1.5% THD

@ 14.4V, 2Ω Mono, 1.5% THD

@ 14.4V, 1Ω Mono, 1.5% THD

Length With EndKaps

Fusing

Recommended Power & Ground Wire

325 x 1

650 x 1 na

325 x 1

650 x 1 na

16”

(40.64cm)

30A x 2

4 GA

SX1250.1

na

625 x 1

1250 x 1 na

625 x 1

1250 x 1

22.50”

(57.15cm)

150A x 1 external

2 GA


35

36

Specifications common to all models.

Height:

Width:

2.5 inches / 6.35 centimeters

10 inches / 25.4 centimeters

Length Without EndKaps: Subtract 5 inches (12.7 cm) from chart above

Frequency Response:

Input Sensitivity:

Signal-t0-Noise Ratio:

20 Hz - 200 Hz, +0 / -1 dB

62.5 mV - 16 V

>98 dB

High Pass Crossover Freq.: 10 Hz - 60 Hz in 1 Hz steps

High Pass Crossover Slope: 0 (off) - 24 dB in 6 dB steps

Low Pass Crossover Freq.: 30 Hz - 200 Hz in 1 Hz steps

Low Pass Crossover Slope: 0 (off) - 48 dB in 6 dB steps

KickEQ Frequency:

KickEQ Bandwidth (Q):

KickEQ Boost/Cut:

20 Hz - 200 Hz in 1 Hz steps

.5 to 10 in .5 steps

+/- 18 dB per Octave

Remote Bass Level Control: Included with each amplifier

Power & Ground Terminals: Will accept up to 2 Gauge wire

DSP Reaction Time / Delay: 0.7 milliseconds

(In other Words...Real Fast!)

Friend’s Reaction:

Stranger’s Reaction:

That Shizzle's Off The Hizzle

Dude...Sweet...

ELECTRONICS LIMITED WARRANTY

Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of 90 DAYS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for TWO (2) YEARS from date of original purchase with receipt. If the product occkk” it is warranted for 9900 D AYYSS from date of original purchase

B SStto

Dealer, it is warranted for O cases you m usstt h

NEE ((11)) YYEEA R from date of purchase with receipt. In all orriig warranty for any reason due to manufacturing defect or malfunction during the warranty period, Kicker will replace or repair (at its discretion) the defective merchandise with equivalent merchandise at no charge. Warranty replacements on

“B-Stock” merchandise may have cosmetic scratches and blemishes.

Discontinued products may be replaced with more current equivalent products.

This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter.

Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you.

This warranty gives you specific legal rights; however you may have other rights that vary from state to state.

WHAT TO DO IF YOU NEED WARRANTY OR SERVICE

Defective merchandise must be returned to your local Authorized Stillwater

Designs (Kicker) Dealer for warranty. Assistance in locating an Authorized Dealer can be obtained by writing or calling Stillwater Designs direct. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.

If it becomes necessary for you to return defective merchandise, call the

Kicker Customer Service Department at (405)624-8510 for a Return Authorization

(RMA) number. Package all defective items in the original container or in a package that will prevent shipping damage, and return to

Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075

The RMA number must be clearly marked on the outside of the package.

Return only defective components. Return of entire cabinets, system packs, pairs, etc. increases your return freight charges. Non-defective items received will be returned freight collect.

Include a dated proof-of-purchase stating the Customer name, Dealer name, product purchased and date of purchase. Warranty expiration on items without proof-of-purchase will be determined from type of sale and the manufacturing date code. Freight must be prepaid; items received freight collect will be refused.

Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service Department at (405)624-8510.

WHAT IS NOT COVERED?

This warranty is valid only if the product is used for the purpose for which it was designed.

It does not cover:

• Damage due to improper installation.

• Subsequent damage to other components.

• Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation.

• Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered abuse.

• Any cost or expense related to the removal or reinstallation of product.

• Speakers damaged due to amplifier clipping or distortion.

• Items previously repaired or modified by any unauthorized repair facility.

• Return shipping on non-defective items.

• Products with tampered or missing barcode labels.

• Products returned without a Return Authorization (RMA) number.

• Freight Damage.

• The cost of shipping product to Kicker.

• Service performed by anyone other than Kicker.

• Speaker with any foreign caulk used for gasket material.

HOW LONG WILL IT TAKE?

Kicker strives to maintain a goal of 24-hour service for all returns.

Delays may be incurred if lack of replacement inventory or parts is encountered.

INTERNATIONAL WARRANTY

Contact your International Kicker dealer or distributor concerning specific procedures for your country’s warranty policies.

P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • 405 624-8510

WARNING:


KICKER drivers are capable of producing sound levels that can permanently damage your hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your hearing.

Please use common sense when controlling volume!

April 2003 37


Notes Pizza Delivery Chic’s Numbers Hook Ups

38

SX .1 Series Amplifiers SX .1 Series Amplifiers

39

No results