KitchenAid | 4176199 | User's Manual | KitchenAid 4176199 User's Manual

Part No. 4176199
Pure Delivery
Water Pump
IMPORTANT:
Read and save
these instructions.
IMPORTANT:
Installer: Leave Installation Instructions with
the homeowner.
Homeowner: Keep Installation Instructions
for future reference.
Save Installation Instructions for local
electrical inspector’s use.
Rev. A
Before you start...
location where water pump will be
installed. Proper installation is your
responsibility. Make sure you have everything
necessary for correct installation.
The rating information is located on the base of
pump.
Check
The water pump can be connected to the refrigerator ice maker and water dispensing system.
Electrical Shock Hazard
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation
is adequate and in conformance with
National Electrical Code, ANSVNFPA 70latest edition**, and all local codes and
ordinances.
Failure to do so could result in fire,
electrical shock or other personal injury.
l
Personal Injury Hazard
Do Not use water pump to pump any
other liquids, use only for bottled water.
Clean system after extended periods of
non-use.
Failure to follow these instructions may
result in personal injury.
Important: Observe all governing codes and
ordinances.
Grounded electrical outlet is required. See
l
l
Electrical requirements.
to pump Do Not require
sealing compounds to prevent leaking.
l
Water connections
A separate water faucet can be connected to
the water pump. The water pump can be
connected to any water faucet that can handle
40-60 PSI. A water faucet kit, Part No.
4319154 is available from your KitchenAid
dealer or authorized parts distributor.
L
**Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Property/Product Damage
Do Not store water bottle and water
pump in an area where temperatures
fall below 32°F.
Failure to follow these instructions may
result in product or property damage.
l
L
Tools needed for
installation:
knife or
tubing cutter
6
12
Parts supplied
for installation:
.
water bottle
tubing
\
outlet
tubing
P
\
Q
\\
bottle cap
4
+
\?
\
l/4” outside
diameter
tubing
/
318” outside
diameter
tubing
‘arts not supplied
‘or installation:
- faucet kit Model
KWPFHXWO (Part
No. 4319154)
If additional tubing is
required, you will need
tubing connector,
Part
No. 4319153 and 114”
O.D. tubing, Part No.
4319151
I
I
switch
Electrical requirements
If codes permit and a separate grounding
wire is used, it is recommended that a
qualified electrician determine that the
grounding path is adequate.
Electrical Shock Hazard
Electrical ground is required on this
appliance.
If cold water pipe is interrupted by
plastic, non-metallic gaskets or other
insulating materials, Do Not use for
grounding.
. Do Not ground to a gas pipe.
Do Not modify the power supply cord
plug. If it does not fit the outlet, have a
proper outlet installed by a qualified
electrician.
Do Not have a fuse in the neutral or
grounding circuit. A fuse in the neutral or
grounding circuit could result in
electrical shock.
. Do Not use an extension cord with this
appliance.
l
l
l
l
- “T” fittings to route
tubing to multiple
locations (Part No.
4319152)
Check with a qualified electrician if you
are in doubt as to whether the appliance
is properly grounded.
This appliance is equipped with a power
supply cord having a 3-prong grounding
plug. To minimize possible shock hazard,
the cord must be plugged into a mating
3-prong grounding-type wall receptacle,
grounded in accordance with National
Electrical Code, ANSVNFPA 70-latest
edition and all local codes and ordinantes. See Figure 1. If a mating wall
receptacle is not available, it is the
personal responsibility and obligation of
the customer to have a properly
grounded 3-prong wall receptacle
installed by a qualified electrician.
Failure to follow these instructions could
result in a serious injury or death.
l
A 120-volt, 60-HZ, AC-only, fused electrical
supply is required. The total circuit ampere
load used including the water pump must not
exceed 90% of circuit-rated ampere capacity.
The ampere rating of the water pump is
located on the base of the pump.
l
3-prong grounding-type
wall receptacle
3-prong
grounding
\
ding
supply
cord
Figure 1
Panel A
Now start...
With pump in room where it
will be installed.
Determine where you wish to locate
water pump and water bottle. The
water bottle and water pump should be installed
on the same level.
The water bottle and water pump must be
located close together since the tubing
connecting the pump to the water bottle is 6 feet
long. Use existing tubing between water
pump and water bottle. Do Not cut this tubing
or add tubing between pump and water
bottle. Do Not remove clamp on end of tubing
that connects inner tubing to outer tubing.
Suggested locations:
l
l
Under the sink - especially for faucet
connection.
Cabinet next to outlet connection.
Route the tubing to the faucet or refrigerator.
Cut tubing to length needed. Use proper fitting to
attach tubing to faucet or refrigerator. A “T”
fitting, (Part No. 4319152), for routing tubing to
more than one location is available from your
KitchenAid dealer or authorized parts distributor.
121
’
Press the switch on the water
pump to the “0” position.
/31
.
Remove bottle cap from water bottle.
Replace empty water bottle. Attach
bottle cap to full water bottle.
El
Plug power supply cord into grounded,
electrical outlet. Press the switch to the
“I” position.
.
14
21
Determine where you will need to run
water lines and the length of tubing that
will be needed. If more tubing is needed
than what is supplied, tubing (Part No.4319151)
and tubing connectors (Part No. 4319153) can
be obtained from your KitchenAid dealer or
authorized parts distributor.
.
.
Press the switch on the water
pump to the “I” position.
If water bottle empties while
unattended, the pump will run for
minutes and then automatically
I
I
2-i/2
shut off.
Press the switch on the water
pump to the “0” position.
ctor
tub
121
.
collet
u-l
1
C1
Attach bottle cap to water bottle.
Push the tubing into the water bottle
until the end of the tubing reaches the bottom of
the bottle. Do Not remove clamp from end of
H Run enough water through faucet
or refrigerator to fill a glass or other
container. Check all connections for leaks. If a
connection leaks, push in collet and remove
tubing. Cut off l/2” of tubing and reinsert into
connector.
If unit is connected ONLY to a refrigerator
icemaker, the icemaker will have to call for water
before pump can be checked for leaks.
tubing.
Keep Installation
Instructions
for future reference.
The instructions
will make it simple to reinstall
your
water pump.
Use and Care
Information
141
Insert one end of the l/4” O.D. outlet
. tubing l/2” to 3/4” into connector
located on outside of pump. Check that you
have pushed tubing into connector as far as it
will go.
The water pump operates
automatically when outlet (faucet,
etc.) is opened. When the outlet is
closed, the water pump automatically
stops operating.
When water bottle empties during
Use: Pressurized air is expelled through faucet
or refrigerator when water bottle is empty.
Turn the faucet to “OFF” position or
stop dispensing from the refrigerator.
Panel B
Remove bottle cap from water bottle.
Replace empty water bottle. Attach
bottle cap to full water bottle.
/31
.
Press the switch on the water pump
to the “I” position.
If water system is ex osed to
temperatures below tl 2-F, the system
must be drained.
Remove tube from bottle. Open all outlets and
run pump to inject air through all outlets.
Cleaning and sanitizing system:
System should be cleaned after extended
periods of non-use.
El
’
Add one-half teaspoon of chlorine
bleach to one gallon of water.
Insert tube into solution and start pump.
131
M-l
.
Open all outlets to fill system with
solution. Let stand five minutes.
.
Flush system with water until
chlorine is removed.
Troubleshooting
Problem
Water pump cycles on
and off:
sause
Water leaks at one or more outlet
connectors.
Solution
l
l
l
Water pump does not run:
Electrical power not being
supplied.
Water bottle is empty.
Check all fittings and water
pump connections for
leaks.
Push in connector and
remove tubing. Cut off l/2”
of tubing and reinsert into
connector.
Do Not cut water bottle to
pump tubing.
Check that power supply
cord is plugged into outlet.
. Check if circuit breaker has
tripped or if fuse has blown.
Check to see if water bottle
is empty. Replace water
bottle according to
instructions.
Press switch on the water
pump to “0” position.
Then press the switch to
the“l” position to reset
motor timer.
l
l
l
l
Water pump operates
continuously until motor
timer stops motor:
Water bottle is empty.
Air in system.
Air leak in water bottle to
pump tubing.
Replace water bottle
according to instructions.
Check that tubing in water
bottle is touching bottom of
bottle. If tubing is too high, it
will take in air.
. Check that tubing is tightly
pushed in place inside water
pump connector.
l
Pure Delivery Water Pump Warranty
Length of Warranty
KitchenAid Will Pay For:
ONE YEAR FULL
WARRANTY
Replacement parts and repair labor to correct defects in materials
or workmanship.
Service must be provided by an authorized
KitchenAid servicing company.
From date of purchase.
KitchenAid Will Not Pay For:
A. Service calls to:
1. Correct the installation of the pump.
2. Instruct you how to use the pump.
3. Replace house fuses, circuit breakers or correct house wiring.
B. Repairs when pump is used in other than normal use.
C. Damage resulting from accident, alteration, misuse, abuse, improper installation or installation
not in accordance with local electrical codes.
E. Replacement parts or repair labor costs for units operated outside the United States.
F. Pick up and delivery.
KitchenAid does not assume any responsibility for incidental or consequential damages. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation
may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state
Panel C
If you need
service...
In the event that your KitchenAid appliance
should need service, call the dealer or store
from which you purchased the appliance or a
KitchenAid-authorized
service company. A
KitchenAid-authorized
service company is listed
in the Yellow Pages of your telephone directory
under “Appliances - Household - Major Service or Repair”. You can also obtain the
service company’s name and telephone number
by dialing, free, within the continental United
States, the KitchenAid Consumer Assistance
Center telephone number, 800-422-l 230. A
special operator will tell you the name and
number of your nearest KitchenAid-authorized
service company.
Maintain the quality built into your appliance call a KitchenAid-authorized
service company.
Download PDF

advertising