KitchenAid | 9871915B | User's Manual | KitchenAid 9871915B User's Manual

INTEGRATED COMPACTOR
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at
www.kitchenaid.com
In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca
Table of Contents............................................................................................................ 2
9871915B
TABLE OF CONTENTS
COMPACTOR SAFETY ..................................................................2
INSTALLATION INSTRUCTIONS ..................................................3
Unpacking ....................................................................................3
Location Requirements ................................................................4
Electrical Requirements ...............................................................5
Undercounter Installation.............................................................5
COMPACTOR USE.........................................................................7
How Your Compactor Works.......................................................7
Loading.........................................................................................7
WHISPER QUIET™ Plus System.................................................7
Starting Your Compactor.............................................................8
Using Solid (Locked) Cycle ..........................................................8
Using the Air Filter or Freshener ..................................................8
Removing a Filled Bag .................................................................8
Installing a New Bag.....................................................................8
COMPACTOR CARE ......................................................................9
Changing the Air Filter or Freshener ............................................9
Cleaning........................................................................................9
TROUBLESHOOTING ..................................................................10
ASSISTANCE OR SERVICE .........................................................11
In the U.S.A. ...............................................................................11
In Canada ...................................................................................11
Accessories ................................................................................11
WARRANTY ..................................................................................12
COMPACTOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed, including the
following:
■
Read all instructions before using the compactor.
■
Close supervision is necessary when used by or
near children. Do not allow to be used as a toy, or
to run unattended at any time. Lock Key Switch
when not in use and store key out of reach of
children.
■
Do not touch moving parts.
■
Do not operate with a damaged cord set, plug,
motor, or after damage in any manner. Have the
compactor examined, repaired or adjusted by an
authorized serviceperson.
■
Use only for intended use as described in this
manual. Do not use other than manufacturer's
recommended attachments.
■
Do not compact toxic or volatile flammable material
such as oily rags and insect sprays. Do not compact
lighted cigarettes, cigars, or other hot or burning
items. Do not overload the compactor.
■
Do not take apart the compactor. Incorrect
reassembly can cause electric shock when
subsequently used.
■
Handle a loaded trash bag with care. Sharp objects
can pierce the bag and cause injury. Do not
overload trash bag with heavy material such as
glass.
■
This compactor is intended for household use only.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Installer: Leave Use and Care Guide with the homeowner.
Homeowner: Keep Use and Care Guide for future reference and
for local electrical inspector’s use, if required.
2. Be sure the power cord is attached to the cord clip on the
rear of the compactor.
A
Unpacking
WARNING
Excessive Weight Hazard
Use two or more people to move and install
compactor.
Failure to do so can result in back or other injury.
IMPORTANT:
■ Do not grasp console to move compactor.
■
Begin in the room where the compactor will be located.
1. Remove compactor from shipping carton. Remove all
protective packaging materials such as tape and shipping
pads. Use a mild detergent and warm water to remove waxy
residue caused by protective shipping material. Dry
thoroughly with a soft cloth. For more information, see
“Cleaning.”
A. Cord clip
3. Place the 2 corner posts from the carton on the floor near the
compactor. Open the compactor drawer and remove any
shipping materials or other items from the drawer. Do not
remove the compactor bag. Grasp the handle and raise the
front of drawer until it clears the drawer stops. Grasp sides of
drawer and lift drawer out of compactor. Place the drawer on
the 2 corner posts.
3
4. Place the other 2 corner posts on the floor to the side of the
compactor. Grasp the sides of the compactor cabinet and put
compactor on its side on top of the corner posts. Remove the
shipping base from the bottom of the compactor.
A
Cutout Dimensions
B
3" min.
(7.6 cm)
A
34¹⁄₄" min.
(87 cm)
A. Leveling legs
B. Shipping base
24" min.
(61 cm)
18" min.
(45.7 cm)
Location Requirements
Product Dimensions
15¹⁄₄" min.
(38.7 cm)
A. Grounded eletrical outlet must be a minimum
of 3" (7.6 cm) away from surrounding cabinets
or nearby walls as shown. It can be placed
either to the left or the right side of the
compactor.
Clearance Dimensions
34¹⁄₈"
(86.7 cm)
15"
(38.1 cm)
24"
(61 cm)
B
A
A. Leave 6" (15.2 cm) of clearance space to the right side of
the compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor
in order to fully open or remove the compactor drawer.
4
Electrical Requirements
WARNING
Undercounter Installation
NOTE: Proper installation is your responsibility. Make sure you
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
National and Local codes and ordinances.
Tools needed:
Gather the required tools and parts before starting installation.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Recommended Grounding Method
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is
recommended that a separate circuit serving only this appliance
be provided.
■
Level
■
Phillips No. 2 screwdriver
■
Tape measure
■
Flat-blade screwdriver
■
Pliers
■
⁵⁄₁₆" Hex-head socket wrench
■
Scissors
■
Utility knife
IMPORTANT:
■ Do not grasp control panel to move compactor.
■
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
■
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
Undercounter Installation
NOTE: Installation hardware is not provided with full cabinet
models.
1. Measure the height of your cabinet opening. The top of the
compactor should be at least ¹₈" (3 mm) from the top of the
cabinet opening.
The rear wheels are preset for a cabinet opening height of
34¹⁄₄" (87 cm) (Position 1).
To adjust for other cabinet opening heights:
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a threeconductor cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Do not connect the
green (or green and yellow) wire to a live terminal.
■
Loosen self-tapping screw just enough to clear stud from
hole in position “1.”
■
Move the rear wheel and stud to position “2” or “3” as
needed for your cabinet opening measurement:
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
■
NOTE: To level the unit in position 3, you may need to
add shims under the leveling legs.
Tighten screw. Repeat for other rear wheel.
B
C
1
2
3
A
D
A. Wheel bracket assembly
B. Cabinet
C. Locating stud
D. Self-tapping screw (pivot)
5
2. Use pliers to lower leveling legs away from cabinet. Adjust
legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm) space
between the top of the compactor and the top of the cabinet
opening. Stand the compactor upright.
3. For model with cabinet, remove the plastic plugs from the
compactor cabinet top.
4. Move the compactor close to its final position.
5. Plug into a grounded 3 prong outlet.
6. Determine if you want the compactor frame or drawer front
flush with the cabinet front.
Using the two #8-18 x ⁵₁₆" screws, install the retaining
brackets to cabinet top as needed:
■
If the compactor frame is to be flush with the cabinet
front, place retaining bracket screws through “1.”
■
If the compactor drawer front is to be flush with the
cabinet front, place retaining bracket screws through “3.”
■
If the compactor is to be midway between “1” and “3,”
place the retaining bracket screws through “2.”
A
B
3 2
Cabinet-front mounting
C
A
B
D
A. Mounting clip
B. Cabinet
C. Retaining bracket
D. Mounting screw
8. Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see if drawer opens
freely. If the toe plate rubs against floor, see “Adjusting the
Toe Plate” for further instructions.
Adjusting the Toe Plate
1
A. Countertop
B. Retaining bracket
7. Slowly lift the front slightly and roll compactor into the cabinet
opening.
Using the two #8-18 x ¹₂" screws, fasten the retaining
brackets to the countertop with the mounting screws.
If brackets cannot be attached to the underside of
countertop, attach mounting clips to brackets. Fasten
compactor to cabinet front with mounting screws through
mounting clips.
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
2. Remove the drawer from the unit. (See Step 3 in the
“Unpacking” section.)
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4. Use scissors or utility knife to cut toe plate along line.
5. Replace drawer. If toe plate still rubs floor covering, repeat
Steps 1-4.
Installing a Custom Panel
Dimensions
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be a minimum of ¹⁄₂" (13 mm)
thick.
Countertop mounting
A
29 ³⁄₈"
(74.6 cm)
B
C
A. Countertop
B. Retaining bracket
C. Mounting screw
15"
(38.1 cm)
Installation
1. Align the bottom of the custom panel with the bottom of the
drawer front.
NOTE: The bottom of the custom panel should not extend
below the bottomof the drawer front.
2. Secure the panel from the back using four #8 x 1" wood
screws as shown.
6
3. Attach a 15" x ¹⁄₂" quarter-round filler along the top of the
drawer front using glue or screws.
B
A
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a “misload” and causes the ram to return to the “up”
position without compacting.
C
C
Loading
IMPORTANT: Do not push items down into compactor with
hands or feet.
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
¹⁄₂ full before the compactor can begin to compress the load.
1. Open the drawer. Lift and pull the handle or press the toe bar
to open the drawer.
NOTE: Pressing the toe bar opens the container only 3" to 6"
(7.6 cm to 15.2 cm), depending on the load.
D
E
F
A. Custom panel
B. 15"x ¹⁄₂" Quarter-round
C. #8 x 1" Wood screws
D. Toe guard
E. Washer
F. Toe guard screw
COMPACTOR USE
How Your Compactor Works
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
NOTE: The compactor drawer should be more than ¹⁄₂ full before
the compactor can begin to compress the load.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about ¹⁄₄ the size of its original bulk.
2. Place trash in compactor.
■ Wrap or cover wet or messy trash.
■
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
■
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
3. Close the drawer.
WHISPER QUIET™ Plus System
The WHISPER QUIET™ Plus system helps to maintain a quiet
home environment during compactor operation.
NOTE: The contents of the trash may affect the noise level of
your compactor. See “Compactor Use.”
7
Starting Your Compactor
1.
2.
3.
4.
5.
Open container. Load trash.
Leave Key-Knob in ON position.
Set Solid Cycle switch to OFF.
Close container.
Lift foot pedal UP to START cycle.
Using Solid (Locked) Cycle
The Solid (Locked) Cycle extends the use of the bag by putting
constant pressure on the trash to keep it from springing back.
Regular use of solid cycle can increase bag capacity up to
25 percent.
During Solid Cycle, the ram will stay in the down position for
extra compacting. The drawer is locked and cannot be opened
when the ram is down.
For best results, use the Solid Cycle for at least 30 minutes at a
time.
1. Open container. Load trash.
2. Set compactor Solid Cycle switch to ON.
Removing a Filled Bag
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
IMPORTANT: Do not push items down into compactor with
hands or feet.
1. Pull the drawer completely open.
2. Remove top of bag from bag retainer buttons. Pull up all four
bag cuffs. Close bag with twist tie provided.
3. Push Side-Lock Latch down and tilt drawer side open.
4. Lift out bag.
3. Close container.
4. Lift the foot pedal UP to START cycle.
5. Container remains LOCKED untill you RESET by lifting the
foot pedal UP.
Using the Air Filter or Freshener
1. Set the Air Filter switch to ON. The fan creates air movement
in the compactor for odor removal.
NOTE: The charcoal Air Flter works only when the Key-Knob
is in the ON position.
IMPORTANT: The air freshener will work with or without the
fan.
2. Set the Air Filter switch to OFF to turn off the fan.
Installing a New Bag
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the “Assistance or Service” section.
IMPORTANT:
Before installing a new bag, be sure:
■ The drawer side is securely locked.
■
The container is clean and free of debris.
1. Place folded bag into the drawer. Open bag and pull top
edges over the drawer top.
2. Lock bag in place by pulling the four prepunched holes over
the bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
8
3. Press inside of bag against the drawer bottom, sides and
corners for a smooth fit.
Cleaning Exterior Surfaces
1. Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
2. Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
Cleaning Inside the Drawer
COMPACTOR CARE
Your new compactor is designed to give you many years of
dependable service. However, there are a few things you are
expected to do in order to properly maintain your compactor.
This section will tell you how to clean and care for your
compactor.
NOTE: You may want to wear protective gloves since there may
be bits of glass in the drawer.
1. Remove the bag. See the “Removing a Filled Bag.”
2. Press down on the lever-action lock (or Side-Lock latch).
Changing the Air Filter or Freshener
It is recommended that you use either the charcoal air filter or the
air freshener in the filter compartment. The solid air freshener
system is an alternative to the air filter and is designed to control
odors that might develop in the trash.
To order the correct replacement charcoal filters or air fresheners,
call the toll-free number listed on the cover or in the “Assistance
or Service” section.
1. Insert fingertips in the air filter cover and pull until the side
tabs release. Then, lift the cover to release the bottom tabs.
2. Remove the air filter by pulling the top edge of the filter. The
filter should pull out easily. Throw away used filter.
OR
Remove the air freshener by simply lifting out of the filter
compartment. Throw away used freshener..
3. Hold the lever-action lock down and tilt the side of the drawer
out until the lock clears the drawer front.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
4. Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted
position.
6. Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7. Latch the drawer side by pushing up the lever-action lock (or
Side-Lock Latch).
Cleaning Inside the Cabinet
3. To replace air filter, push the replacement filter into place.
OR
NOTE: You may want to wear protective gloves since there may
be bits of glass in the cabinet.
1. Pull the drawer out until it stops.
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
To replace the air freshener, place the replacement in the filter
compartment.
4. Insert the bottom tabs of the air filter cover and push in until
the side tabs snap into place.
Cleaning
Before cleaning the compactor, turn the Key-Knob (or KeySwitch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
2. Lift the front of the drawer to clear the stops.
9
3. Grasp the drawer on the sides and pull it out the rest of the
way. Set the drawer down gently.
Cleaning the Ram
NOTE: You may want to wear protective gloves since there may
be bits of glass on the ram cover.
1. Wipe glass particles off of the ram cover with a cloth or paper
towels.
2. Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
4. Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum
designed to pick up liquids.
Cleaning Before a Vacation
5. Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
6. To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children’s reach.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Trash is not compacting
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted.
■
The drawer won’t open
■
To raise the ram on models with a Key-Knob (or KeySwitch): Turn the Key-Knob (Key-Switch) to START and
release. See “Starting Your Compactor.”
Your compactor won’t operate
■
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
■
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■
Is the drawer completely closed? Close the drawer firmly
and start the compactor again.
■
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See “Starting Your Compactor.”
■
To raise the ram on models with push button controls:
Press OFF, and then press ON. See “Starting Your
Compactor.”
■
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
There is not enough compaction or force
■
Did you press ON before pressing START? Press ON
before pressing START (on some models). See “Starting the
Compactor.”
Do you use the compacting cycle frequently enough?
Compacting works best when only a few items are loaded.
Bottles don’t break
■
10
Is the ram all the way up? Drawer will open only when ram is
fully raised.
How often do you notice this? Bottles will not break every
time. The thickness of the bottle’s glass and the content of
the trash load below it may keep the bottle from breaking.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new KITCHENAID® appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
In the U.S.A.
Call the KitchenAid Customer eXperience Center
toll free: 1-800-422-1230
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■
Installation information.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in the United States.
To locate the KitchenAid designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to KitchenAid with
any questions or concerns at:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the KitchenAid Canada Customer Interaction Centre toll free:
1-800-807-6777.
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■
Warranty information.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to KitchenAid
Canada with any questions or concerns at:
KitchenAid Canada
Customer Interaction Centre
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
Accessories
To ensure the proper functioning of your compactor, use
KITCHENAID® replacement parts only. To order replacement
parts or accessories, call 1-800-462-3819 and ask for the
appropriate part number listed below or contact your authorized
KitchenAid dealer. In Canada, call 1-800-807-6777.
Replacement Parts
Replacement Bags - Call for Part Number.
Charcoal Air Filters - Order Part Number 4151750.
Air Fresheners (scent):
Order Part #9872166GA (Fresh Green Apple)
Order Part #9872166L (Lavender)
Order Part #9872166LG (Lemon Grove)
Color Panel Kits and Handles
See section “Installing a Custom Panel” for custom panel
dimensions.
Color Panel with Handles:
Order Part #4396299 (Cobalt Blue)
Order Part #4396300 (Empire Red)
Order Part #4396301 (Majestic Yellow)
Order Part #4396296 (Black)
Order Part #4396297 (White)
Order Part #4396298 (Biscuit)
Handles:
Order Part #9871564 (Brushed stainless steel)
Order Part #9871564W (White)
Order Part #9871564B (Black)
Order Part #9871564T (Biscuit)
11
KITCHENAID® COMPACTOR WARRANTY
ONE-YEAR LIMITED WARRANTY
For one year from the date of purchase, when this compactor is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada will pay for factory specified parts and repair labor costs to correct
defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
KitchenAid or KitchenAid Canada will not pay for:
1. Service calls to correct the installation of your compactor, to instruct you how to use your compactor, to replace household fuses, or
to correct household wiring.
2. Repairs when your compactor is used in other than normal, single-family household use.
3. Pickup and delivery. Your compactor is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not
approved by KitchenAid or KitchenAid Canada.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Charcoal Filters.
8. In Canada, travel or transportation expenses for customers who reside in remote areas.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY
BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND
PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR
REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY.
KITCHENAID OR KITCHENAID CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to
determine if another warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the KitchenAid Customer eXperience Center, 1-800-422-1230 (toll-free),
from anywhere in the U.S.A. In Canada, contact your designated KitchenAid Canada servicer or call 1-800-807-6777.
6/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your compactor to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the inside panel of the compactor
drawer.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number __________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
9871915B
© 2005. All rights reserved.
Tous droits réservés.
® Registered Trademark/TM Trademark of KitchenAid, U.S.A., KitchenAid Canada licensee in Canada
® Marque déposée/TM Marque de commerce de KitchenAid, U.S.A., Emploi licencié par KitchenAid Canada au Canada
7/05
Printed in U.S.A.
Imprimé aux É.-U.
Download PDF

advertising