portable stereo fm radio with cd-player and cassette scd-420

portable stereo fm radio with cd-player and cassette scd-420
PORTABLE STEREO FM RADIO WITH
CD-PLAYER AND CASSETTE
SCD-420
INSTRUCTION MANUAL
For information and support, www.lenco.com
WARNING
CLASS 1 LASER PRODUCT
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
This product contains a low power laser device.
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage
it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local voltage.
ON CONDENSATION
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the CD player.
• When there is condensation inside the unit, the unit may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
* Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.
* Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspapers,
table-cloths, curtains, etc..
* Do not place naked flame sources, such as lighted candles on the apparatus.
* Take attention to the environmental aspects of battery disposal.
* Use the apparatus only in moderate climates.
* Do not expose the apparatus to dripping or splashing.
* Do not place objects filled with liquids, such as vases, on the apparatus.
* Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
* The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightening flash
with arrowhead symbol
within the triangle is a
warning sign alerting
the user of "dangerous
voltage" inside the unit.
ATTENTION : To reduce the risk
of electric shock, do not remove the
cover. There are no user serviceable
parts inside the unit. Refer all servicing
to qualified personnel.
The exclamation point within
the triangle is a warning sign
alerting the user of important
instructions accompanying
the product.
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from mains supply.
THE MARKING PLATE IS LOCATED AT THE BACK OF ENCLOSURE OF THE APPARATUS.
LOCATION OF CONTROLS
1. VOLUME CONTROL
2. FUNCTION SWITCH
3. CARRYING HANDLE
4. CASSETTE PAUSE
5. CASSETTE STOP/EJECT
6. CASSETTE F.FWD
7. CD DOOR
8. CASSETTE REWIND
9. CASSETTE PLAY
10. OPEN / CLOSE CD DOOR AREA
11. LCD DISPLAY
12. TUNING CONTROL
13. PROG/CLK-ADJ./PLAY MODE
BUTTON
14.SPEAKER
15. CD NEXT BUTTON
16. PLAY/PAUSE
BUTTON
17. CASSETTE DOOR
18. CD STOP
BUTTON
19. CD BACK BUTTON
20. STANDBY BUTTON
21. PHONES JACK
22. TELESCOPIC ANTENNA
23. BATTERY COMPARTMENT
24. AC SOCKET
POWER SUPPLY
USING HOUSE CURRENT
Before use, check that the rated voltage
of your unit matches your local voltage.
To AC socket
Note: Plug is used as the disconnect device.
The disconnect device shall remain readily
operable.
To AC outlet
USING BATTERIES
Disconnect the AC power cord from the AC inlet of the
unit. Battery power is cut automatically by the cord while
it is connected.
battery door
When the volume decrease, or the sound distorts, replace
all of the batteries with new ones.
Insert eight UM-2 ( size C ) batteries.
GB 1
TURN ON / OFF THE SYSTEM
Press the STANDBY button to turn the audio on.
To change the audio mode between CD, RADIO AND TAPE ,
set the FUNCTION switch while the power is on.
The audio mode is displayed.
Turn off the unit by pressing the STANDBY button.
" OFF " word will be shown on the display and then resume the current time.
STANDBY
CLOCK ADJUSTMENT
The clock is displayed on LCD display at standby mode.
1. Press and hold the PROG / CLOCK-ADJ./PLAY MODE button,
2. Press the NEXT or BACK to select 12 hours or 24 hours display.
3. Press the PROG / CLOCK-ADJ./PLAY MODE button, the hour digit flash.
4. Press the NEXT or BACK to adjust hour digit.
5. Press the PROG / CLOCK-ADJ./PLAY MODE button,
the minute digit flash.
6. Press the NEXT or BACK to adjust minute digit.
7. Press the PROG / CLOCK-ADJ./PLAY MODE button again,
LCD display
the correct time is shown on display.
CLOCK-ADJ.
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
MIN.
FOR PRIVATE LISTENING
Plug in headphones (ø3.5 mm stereo mini-plug) to the
PHONES jack.
When headphones are plugged in, the speakers are
automatically disconnected.
MAX.
VOLUME
LISTENING TO THE RADIO
1 . Turn on the unit by
pressing the STANDBY button.
3 . Tune in to a station.
TUNING
STANDBY
4 . Adjust the sound.
2 . Set to RADIO
FUNCTION
RADIO
LCD display
MIN.
MAX.
VOLUME
GB 2
FOR BETTER RECEPTION
FM
AFTER LISTENING
Turn off the unit by pressing the STANDBY button.
COMPACT DISC PLAYBACK
4.
5 .
1 . Turn on the unit by
pressing the
STANDBY button.
STANDBY
2 . Set to CD
Insert a disc with the label side facing up.
Close the disc holder.
The disc will rotate and
the total tracks of the disc
will show on the display.
FUNCTION
CD
6. Press the PLAY/PAUSE
button.
Track number "01" & the symbol " " will be shown during normal compact disc playback.
3 . Open the disc holder by pushing the CD door open area.
LCD display
TO INTERRUPT PLAYBACK
Press the Play/Pause button and the symbol " " will
be flashed. Press the button again to resume playback.
LCD display
TO STOP PLAYBACK
Press the STOP button and the display
shows the total tracks of the disc.
PLAY/PAUSE
TO SKIP TO THE BEGINNING OF A TRACK
•
Press either one of the skip buttons according to the desired skip direction.
•
Play/back resumes from the selected track.
•
When the button is pressed once during play, the previous track starts again.
•
When the button is pressed once during play, the next track plays.
LCD display
SEARCHING FOR A PASSAGE WITHIN A TRACK
•
Keep the or button pressed during playback,
and release the button as soon as you recognise the
desired passage. Then normal CD playback will resume from this point.
Unit will be automatically off within 30mins without further operation (in stop mode / CD door open).
GB 3
REPEAT , REPEAT ALL AND MIX PLAYBACK
Press PLAY MODE button during CD playback. CD plays with a single track repeat,
all tracks repeat or randomly.
PLAY MODE
FOR NORMAL COMPACT DISC PLAYBACK
Mode sequence REPEAT >> REPEAT ALL >> MIX >> CLEAR.
During Mix mode,
display shows
During Repeat 1 mode,
display shows
LCD display
During Repeat 2 mode,
display shows
LCD display
PROGRAMMED PLAYBACK
PROGRAMMED PLAYBACK
FOR NORMAL COMPACT DISC PLAYBACK
Programmed playback enables tracks on a disc to be played
in the desired order. Up to 20 tracks can be programmed.
1. Press the " PROGRAM " button.
2. Press the " NEXT " and " BACK " buttons to select the desired track number.
3. Press the " PROGRAM " button again to memorize the track.
4. Repeat steps 2 and 3 until all desired tracks are programmed.
5. Press the " PLAY/PAUSE " button to start.
" " , " PROG " & track number are shown on the
LCD display.
6. Press the " STOP " button once to stop programmed
playback.
7. Press the " PLAY/PAUSE " button to resume
programmed playback.
8. Open the CD door, turn off the CD player or press
the " STOP " button twice to clear the programmed memory.
Note : Programming can only be made when the player is in stop mode.
LCD display
LCD display
" PROGRAM "
Note on CD-R/RW discs
- Because of non-standardized format definition/ production of CD-R/RW,
playback quality and performance are not guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions, such as PC performance, writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- It is recommended to record only audio files on CD-R/RW discs for easy reading.
GB 4
TAPE PLAYBACK
1 . Set to TAPE
FUNCTION
TAPE
2 . Insert the cassette.
3 . Press the
PLAY button.
PLAY
TO STOP PLAYBACK
Press the STOP / EJECT button.
TO INTERRUPT PLAYBACK
Press the PAUSE button.
To resume play, press the PAUSE button again.
TO FAST WIND
Press the REWIND or F.FWD button. Press the STOP/EJECT
button to stop winding at the desired position.
MAINTENANCE
CLEANING CD
If the CD skips or will not play , the disc may need
cleaning. Before playing, wipe the disc
from the centre out with a
cleaning cloth. After playing,
store the disc in its case.
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower.
Blow several times on the lens and remove the dust
with the brush. Finger prints may be removed with
a cotton swab moistened with alcohol.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping
with a soft cloth.
IMPORTANT NOTE
If an abnormal display indication or an operating problem occurs,
disconnect the AC power cord and remove the batteries. Wait at least 5
seconds, then reconnect the AC power cord or reinstall the batteries.
WARNING
Should the CD door be opened before the reading of the CD completed, a
jamming noise may occur. This is resolved by closing the CD door.
GB 5
SPECIFICATIONS
CASSETTE SECTION
Track format:
Tape speed:
F.F. & REW time:
Frequency response:
2 track stereo
4.75 cm / sec.
170 sec. (F-60 tapes)
125 Hz - 8000 Hz (Normal tape)
CD SECTION
Channels:
S / N ratio:
Wow & Flutter: Sampling frequency:
Quantization:
Pick up light source: Pick up wave length
2 channels
60 dB
undetectable
44.1 kHz 8 x over sampling
1 bit DA converter
Semi - conductor laser
790 mm
RADIO SECTION
Tuning ranges:
Antennas:
FM 87.5 - 108 MHz
FM Rod antenna
GENERAL
Output power:
1.2W + 1.2W (RMS)
Power consumption:
13W
Speaker: 3" 8 OHM
Phones jack:
3.5MM
Power source: AC : 230V~50Hz
DC : 12V ( 8 x 1.5V LR14/"C"/UM2 )
Dimensions:
288(L) x 238(D) x 155(H)mm
Weight
2.2 KGS
Due to continuing improvement, the features and the design are subject to change without notice.
Guarantee
Lenco offers service and warranty in accordance with the European law, which means that in case of repairs (both during and after the warranty period)
you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation
may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation. No
legal right or entitlements may be obtained from the description made in this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general
household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose
them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries.
In so doing, you will help to conserve natural resources and improve standards of environmental protection in
treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
CE Marking
Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive
(2014/35/EU) issued by the Commission of the European Community.
Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at [email protected]
WARNING: Prolonged exposure to loud sounds from personal music players may lead to temporary or
permanent hearing loss.
Where to place the item :
Today’s furniture is coated with a wide variety of lacquers and synthetic-coatings that are treated with an extensive range of cleaning products. Therefore,
the possibility that some of these substances contain components that react adversely to the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause discoloring to furniture surfaces. If necessary, place the appliance on a non-slide surface.
®All rights reserved
Service
For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, Nuth, The Netherlands
GB 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement