Relays and Timers Technical Data
Technical Data
Relays and Timers Specifications
Bulletin Number 700
Topic
Page
General Purpose Relays
2
Timing Relays
41
NEMA Industrial Relays
81
IEC Control Relays
93
Solid State Relays
109
Additional Resources
These documents contain additional information concerning related products from Rockwell Automation.
Resource
Description
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Provides general guidelines for installing a Rockwell Automation industrial system.
Product Certifications website, http://www.ab.com
Provides declarations of conformity, certificates, and other certification details.
You can view or download publications at http://www.rockwellautomation.com/literature/. To order paper copies of
technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.
700-HA General Purpose Relay
Relays and Timers Specifications
Cat. No. 700-HA…
Electrical Ratings
Pilot Duty Rating‡
NEMA B300
Rated Thermal
Current (Ith )
HA = 10 A – 120V, 240V
HAX = 6 A – 120V, 240V
Rated Insulation Voltage (Ui)
Contacts
250V IEC – 300V UL/CSA
Inductive
Make
Break
Hp
120V AC
30 A
3A
1/3
240V AC
15 A
1.5 A
1
General Purpose
10 A, 240V AC
Resistive
10 A, 30V DC
Min. Low Energy Permissible Load
HA = 10V, 5 mA
HAX = 5V, 2 mA
Permissible Coil Voltage Variation
Pickup: 80…110% of Nominal Voltage at 50 Hz
80…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Coil Consumption ±10%
AC Coils
50 Hz
Inrush
3.3 VA
60 Hz
2.85 VA
Sealed
2.2 VA
1.9 VA
DC Coils
1.3 W
20% of nominal V AC
Must Dropout Voltage
10% of nominal V DC
50 MΩ (700-HA and 700-HAB)
30 MΩ (700-HAX)
Max. Contact Resistance
Design Specification/Test Requirements
Electrical
Pole-to-Pole
2000V
Contact to Coil
2000V
Electrical Life (Operating)
100 000 min.
Degree of Protection
(Open Type) IEC 529
IP 40
Mechanical Life Cycles (AC/DC)
> 20 x 106/ 50 x 106
Mechanical
Switching Frequency Operations
3600/HR
Coil Voltages
See Product Selection
Operating Time
Max. Pickup
10 ms
Max. Dropout
10 ms
Endurance
5G
Operational
2.5 G
Endurance
50 G
Operational
9G
Operating
AC/DC
–40…+70 °C
Storage
AC/DC
–40…+100 °C
Maximum Operating Rate
Vibration
Shock
4 Ops/s
Environmental
Temperature
Altitude
2000 m (6560 ft)
Insulating Material
Molded High-Dielectric Material
Enclosure
Transparent Dust Cover
Construction
Contact Material
700-HA:
10 A– AgNi
700-HAX:
6 A–Bifurcated/Gold Plating AgNi
Terminal Markings on Socket
In accordance with EN50 0005
Sockets
8-Pin Socket — 700-HN100, -HN125, -HN204
11-Pin Socket — 700-HN101, -HN126, -HN205
Certifications
cURus Recognized (File No. E3125, Guide NLDX2/NLDX8), cULus Listed when used with
Bulletin 700-HN sockets noted above (File No. E3125, Guide NLDX/NLDX7), CE Marked, CSA
Certified, UR Certified (File 229473)
Standards
UL508, CSA C22.2 No. 14, EN 61810-1
‡ NEMA Rating Chart is in publication 700-SG003*
2
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timers Specifications
700-HA General Purpose Relay
k Reduction Factor
Cycles
Max. Switching Current (A)
700-HA Relay Performance Graphs
Load (kVA)
Contact life vs. AC1 load at 1,800 cycles/h
Voltage DC (V)
Breaking capacity for DC1 load at 1,800 cycles/h.
COS
Load reduction factor vs. cos φ
A = load applied to one contact
B = load applied to two contacts in series
C = load applied to three contacts in series
Time Module Cat. No. 700-HT3
Electrical Ratings
Operating Voltage Range
12…240V AC (50/60 Hz) 12…240V DC
Power Consumption
0.1 W (12V)
1.0 W (230V)
Degree of Protection of Input (B1) Terminal
IP 20 (Guarded Terminal)
Input Terminal Wire Range
1.0 x 0.2 mm2…2.5 mm2 (24 AWG…14 AWG)
2.0 x 0.2 mm2…1.5 mm2 (24 AWG…16 AWG)
Mechanical
Input Terminal Torque Range
0.45…0.8 Nm (4…7 lb-in.)
LED Indicator
Red
Repeat Accuracy‡
±1%
Recovery Time
<50 ms
Selectable Timing Ranges
Three DIP switches, seven ranges (set from 5…100% of range):
1 s, 10 s, 100 s, 10 min, 100 min, 10 h, 100 h
Selectable Timing Modes
Three DIP switches, eight modes:
1. Power On–Delay
2. Power On One-Shot
3. Power On Repeat Cycle, On Start
4. Signal On-Delay and Signal Off-Delay
5. Signal Off-Delay
6. Signal On-One-Shot
7. Signal Off-One-Shot
8. Signal On and Signal Off Watchdog Monitor
Adjustable Trimmer Scale Accuracy
±5% of Time Range
Environmental
Temperature
Operating
Storage
–20 °C…+50 °C (–4 °F…+122 °F)
–55 °C…+85 °C (–67…+185 °F)
Altitude
2000 m (6560 ft)
Enclosure
Gray Plastic Housing
Mounting with Socket Only
8- or 11-Pin Socket with Module Plug
Sockets
700-HN204 (8-Pin with Plug)
700-HN205 (11-Pin with Plug)
Certifications
cURus Recognized (File No. E14843, Guide NRNT2/NRNT8), CE Marked
Standards
UL508, CSA C22.2 No. 14, EN 61810-1
Construction
‡ At constant voltage and temperature.
Rockwell Automation Publication 700-TD552A-EN-P
3
700-HA General Purpose Relay
Relays and Timer Specifications
Timing Charts, Cat. No. 700-HT3 Multi-Function Time
Module (t = Time Range 0.05 s…100 h)
Terms:
U is Power Input
R is Relay Output
S Signal, +A1 Socket, B1 Timer
t is the resulting Time Delay (Red LED)
3. Power On Repeat Cycle, On Start
Apply power (U) to timer. Relay contacts (R) change state
immediately and the time delay (t) begins. When the time delay is
complete, the contacts return to their shelf state for time delay (t)
(time on = time off). This cycle will repeat until the power is
removed. Terminal B1 is not used in this mode.
1. Power On-Delay
Apply power (U) to timer. Relay contacts (R) change state after time
delay (t) is complete. Contacts return to their shelf state when power
is removed. Terminal B1 is not used in this mode.
4. Signal On-Delay and Signal Off-Delay
2. Power On One-Shot
Apply power (U) to timer. Relay contacts (R) change state
immediately and the time delay begins. When the time delay (t) is
complete, contacts return to their shelf state. Contacts return to
their shelf state when power is removed. Terminal B1 is not used in
this mode.
4
Apply power (U) to timer. When the signal (S) is closed the time
delay (t) begins, after the time delay is complete the relay contacts
(R) change state. Opening the signal starts the time delay, after the
time delay is complete the contacts return to their shelf state. If the
signal is closed or opened before the time delay is complete, the
time delay is reset. Contacts return to their shelf state when power
is removed.
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HA General Purpose Relay
Cat. No. 700-HT3 Timing Modes, Time Description, Timing
Charts, and DIP Switch Selections
5. Signal Off-Delay
Apply power (U) to timer. When the signal (S) is closed, the relay
contacts (R) change state immediately. When the signal is opened,
the time delay (t) begins. If the signal is closed before the time delay
is complete, the time delay is reset and the relay remains energized.
When the time delay is complete, the contacts return to their shelf
state. Contacts return to their shelf state when power is removed.
7. Signal Off One-Shot
Apply power (U) to timer. When the signal (S) is closed and then
opened, the relay contacts (R) change state immediately and the
time delay (t) begins. After the time delay begins, opening or closing
the signal will not reset the time delay. When the time delay is
complete, the contacts return to their shelf state. Contacts return to
their shelf state when power is removed.
8. Signal On and Signal Off Watchdog Monitor
6. Signal On One-Shot
Apply power (U) to timer. When the signal (S) is closed, the relay
contacts (R) change state immediately and the time delay (t) begins.
After the time delay begins, opening or closing the signal will not
reset the time delay. When the time delay is complete, the contacts
return to their shelf state. Contacts return to their shelf state when
power is removed.
Apply power (U) to timer. When the signal (S) is closed, the relay
contacts (R) energize immediately and the time delay (t) begins. If
the signal is opened before the time delay is complete, the relay
remains energized and the time delay is reset. When the time delay
is complete the contacts return to their shelf state. If the signal is
opened after the time delay is complete, the relay contacts energize
immediately and the same time delay begins. Continuous cycling of
the signal at a rate that is faster than the time delay will cause the
relay contacts to remain energized. Contacts return to their shelf
state when power is removed.
Rockwell Automation Publication 700-TD552A-EN-P
5
700-HA General Purpose Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
54.1
(2-1/8)
32.8
(1-3/10)
36.5
(1-9/20)
Bulletin 700-HA Relay
12.5
(1/2)
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
6
Cat. No.
A
B
C
D
Approx. Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HA General Purpose Relay
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
24.6
(31/32)
40.1
(1-37/64)
20.8
(53/64)
30.0
(1-3/16)
26
(1-1/32)
24.9
(63/64)
65.0
(2-35/64)
54.9
(2-5/32)
51.1
(2-1/64)
4.2
(5/32)
38.0
(1-1/2)
#4–40
M3
Cat. No. 700-HN100
33.0
(1-19/64)
14.7
(37/64)
Panel Mounting
Cat. No. 700-HN125
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2-14 AWG… #2-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Wire Size: 2 x 2.5 mm2
Single Wire – Up to 12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG…#2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
26
(1-1/32)
30
(1-3/16)
59.2
(2-1/3)
7.9
(0.31)
24.6
(31/32)
20.8
(53/64)
26.9
(1.06)
65.0
(2-35/64)
54.9
(2-5/32)
4.2
(5/32)
51.1
(2-1/64)
38.0
(1-1/2)
#4-40
M3
Cat. No. 700-HN101
52.3
(2.06)
Panel Mounting
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG…#2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Cat. No. 700-HN126
2
Wire Size: 2 x 2.5 mm
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG…#2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
7
700-HA General Purpose Relay
Relays and Timer Specifications
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
33.5
(1.32)
33.5
(1.32)
26.9
(1.06)
11.0
(0.43)
77.5
(3.05)
3.2
(0.13)
26.9
(1.06)
11.0 (0.43)
20.4
(0.80)
20.4
(0.80)
77.5
(3.05)
49.7
(1.96)
3.2 (0.13)
35.5
(1.40)
16.8
(0.66)
21.6
(0.85)
16.8
(0.66)
38.0
(1.50)
38.0
(1.50)
Cat. No. 700-HN204
Cat. No. 700-HN205
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG …#2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
38.0
(1.50)
54
(2.13)
6.3
(0.25)
10.5
(0.41)
Cat. No. 700-HT3
2
Wire Size: 2 x 1.5 mm (#2 – 16 AWG…#1–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
35.5
(1.40)
21.6
(0.85)
4.0 (0.16)
4.0 (0.16)
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
8
49.7
(1.96)
Relays and Timer Specifications
700-HB General Purpose Relay
Specifications
Cat. No. 700-HB…
Electrical Ratings
Pilot Duty Rating‡
NEMA B300
Rated Thermal
Current ( Ith )
15 A – 120V, 240V
Rated Insulation Voltage (Ui)
250V IEC-300V UL/CSA
Make
Break
Hp
Inductive
Contacts
2 -Pole
3 -Pole
2 -Pole
120V AC
60 A
30 A
6A
3A
3/4
240V AC
30 A
15 A
3A
1.5 A
2
General Purpose
3 -Pole
15 A, 240V AC
Resistive
15 A, 30V DC
Min. Low Energy Permissible Load
1000 mW (10V, 10 mA)
80…110% of Nominal Voltage at 50 Hz
Permissible Coil Voltage Variation
80…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Coil Consumption
±10%
AC Coils
50 Hz
60 Hz
Inrush
3.3 VA
2.85 VA
Sealed
2.2 VA
1.9 VA
DC Coils
1.3 W
25% of VA
Max. Allowable Leakage
10% of W
Max. Contact Resistance
50 mΩ
Design Specification/Test Requirements
Electrical
Dielectric Withstand Voltage
Pole-to-Pole
2500V
Contact to Coil
4000V
Mechanical
Degree of Protection
(Open Type) IEC 529
IP 40
> 10 x 106/30 x 106
Mechanical Life Cycles (AC/DC)
Switching Frequency Operations
3600/HR
Coil Voltages
Operating Time
(ms)
See Overview/Product Selection
Pickup
20 ms
Dropout
4 ms
Maximum Operating Rate
Vibration
Shock
4 Ops/s
Endurance
5G
Operational
1.5 G
Endurance
50 G
Operational
15 G
Environmental
Temperature
Operating
AC/DC
–40…+70 °C
Storage
AC/DC
–40…+100 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High Dielectric Material
Enclosure
Transparent Dust Cover
Contact Material
AgCdO
Terminal Markings on Socket
In accordance with EN50 0005
Sockets
Certifications
700-HN153, -HN154
cURus Recognized (File No. E3125, Guide NLDX2/NLDX8), cULus Listed when used with Bulletin 700-HN sockets
noted above (File No. E3125, Guide NLDX/NLDX7), CE Marked, CSA Certified, UR Certified (File No. 229473)
Standards
UL508, CSA C22.2 No. 14, EN 61810-1
‡ NEMA Rating Chart is in publication 700-SG003*
Rockwell Automation Publication 700-TD552A-EN-P
9
700-HB General Purpose Relay
Relays and Timer Specifications
Cycles
Technical Data
Load (kVA)
Maximum Switching Current (A)
Contact life vs AC1 load at 600 cycles/h.
Voltage DC (V)
Reduction Factor
Breaking capacity for DC1 load at 600 cycles/h.
Load applied to 1 contact.
A = for N.O. types
B= other types
(Highly Resistive)
COS
(Inductive)
Load Reduction factor vs cos φ
10
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HB General Purpose Relay
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
60.9
(2.40)
35.8
(1.41)
38.2
(1.50)
30.25
(1.19)
27.0
(1.06)
40
(1.57)
34.3
(1.35)
Ø 3.2
(0.13)
51.4
(2.02)
91.3
(3.59)
35.4
(1.39)
95.3
(3.75)
46.3
(1.82)
21.6
(0.85)
35.5
(1.40)
Bulletin 700-HB Relay
32.0
(1.26)
Cat. No. 700-HN153
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
11
700-HB General Purpose Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
38.0
(1.50)
49.5
(1.95)
25.6
(1.01)
35.4
(1.40)
54
(2.13)
84.85
(3.34)
84.3
(3.32)
6.3
(0.25)
10.5
(0.41)
41.5
(1.63)
4.0
(0.16)
Cat. No. 700-HN154
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
12
Cat. No. 700-HT3
Wire Size: 2 x 1.5 mm2 (#2–16 AWG…#1–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HD General Purpose Relay
Specifications
Cat. No. 700-HD…
Electrical Ratings
Pilot Duty Rating‡
NEMA B300
Rated Thermal Current ( Ith )
15 A§ – 120V
15 A§ – 240V
Rated Insulation Voltage (Ui)
250V IEC-300V UL/CSA
Make
Inductive
Contacts
Break
Hp
2-Pole
3-Pole
2-Pole
120V AC
60 A
30 A
6A
3A
3/4
240V AC
30 A
15 A
3A
1.5 A
2
General Purpose
3-Pole
15 A, 240V AC
Resistive
15 A, 30V DC
Min. Low Energy Permissible Load
1000 mW (10V, 10 mA)
Permissible Coil Voltage Variation
80…110% of Nominal Voltage at 50 Hz
80…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Coil Consumption
±10%
AC Coils
50 Hz
60 Hz
Inrush
3.3 VA
2.85 VA
Sealed
2.2 VA
1.9 VA
DC Coils
1.3 W
Maximum Contact Resistance
50 mΩ
20% of Nominal V AC
10% of Nominal V DC
Must Dropout Voltage
Design Specification/Test Requirements
Electrical
Dielectric Withstand Voltage
Pole-to-Pole
2500V
Contact to Coil
4000V
Mechanical
Degree of Protection
(Open Type) IEC 529
IP 40
> 10 x 106 / 30 x 106
Mechanical Life Cycles (AC/DC)
Switching Frequency Operations
3600/HR
Coil Voltages
Operating Time
See Overview/Product Selection
Pickup
20 ms
Dropout
4 ms
Maximum Operating Rate
4 Ops/s
Minimum Low Energy Permissible Load
1000 mN (10V, 10mA)
Environmental
Temperature
Operating
–40…+70 °C
Storage
–40…+100 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High Dielectric Material
Enclosure
Transparent Dust Cover
Contact Material
Silver Cad. Ox.
Terminal Markings
Certifications
In accordance with EN50 0005
cURs Recognized (File No. E3125, Guide NLDX2/NLDX8), CSA Certified (File No. 229473), CE Marked, UR
Certified
Standards
UL 508, CSA C22.2 No. 14, EN 61810-1
‡ NEMA Rating Chart is on page 19 of publication 700-SG003*
§ 3-pole relays have a 20 A maximum total current rating for all three poles.
Note: Bulletin 700-HD wiring terminals are the quick connect/solder type 4.7 x 0.5 mm (0.187 x 0.020 in.) termination.
Rockwell Automation Publication 700-TD552A-EN-P
13
Relays and Timer Specifications
Cycles
Maximum Switching Current (A)
700-HD General Purpose Relay
Voltage DC (V)
Load (kVA)
Breaking capacity for DC1 load at 600 cycles/h.
Contact life vs AC1 load at 600 cycles/h.
Reduction Factor
Load applied to 1 contact.
A = for N.O. types
B= other types
(Highly Resistive)
COS
(Inductive)
Load Reduction factor vs cos φ
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
35.9
(1.41)
63
(2.48)
68
(2.67)
38.2
(1.50)
Bulletin 700-HD Relay
14
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HC Relays
Specifications
Cat. No. 700-HC…
Electrical Ratings
Pilot Duty Rating ‡
NEMA C300, R300
Rated Thermal
Current (Ith)
7 A and 10 A
Rated Insulation Voltage (Ui)
250V IEC – 300V UL/CSA
Inductive
Contacts
700-HC_4
Hp
700-HC22
Hp
120V AC
15 A
1.5 A
1/8
15 A
1.5 A
1/3
240V AC
7.5 A
0.75 A
1/3
7.5 A
0.75 A
3/4
General Purpose
7 A, 277V AC
10 A, 277V AC
Resistive
7 A, 30V DC
10 A, 24V DC
100 mW (10V, 10 mA) - Silver Contacts
50 mW (5V, 10 mA or 25V, 2 mA) - Gold Contacts
Min. Low Energy Permissible Load
80…110% of Nominal Voltage at
50 Hz
Permissible Coil Voltage Variation
Pickup:
20% of Nominal Voltage at AC
Must Dropout
Voltage:
80…110% of Nominal Voltage at
60 Hz
10% of Nominal Voltage at DC
80…110% of Nominal Voltage at
DC
Coil
Consumption
±10%
AC Coils
50 Hz
60 Hz
Inrush
2.2 VA
1.6 VA
Sealed
1.3 VA
1.1 VA
DC Coils
1.0 W
20% of VA (AC)
Max. Allowable Leakage
10% of W (DC)
Design Specification/Test Requirements
Electrical
Dielectric Withstand Voltage
Pole-to-Pole
2000V
Contact to Coil
4000V
Electrical Life (Cycles)
100 000 minimum
Mechanical
Degree of Protection
(Open Type) IEC 529
IP 20 (Guarded Terminal Sockets)
20 x 106 (AC) 50 x 106 (DC)
Mechanical Life Cycles
Switching Frequency Operations
1800/HR
Coil Voltages
Operating Time (ms)
See Product Selection
Max. Pickup
10
Max. Dropout
3
Maximum Operating Rate
8 cycles/s
Environmental
Operating
Temperature
Storage
Altitude
Insulating Material
Enclosure
Contact Material
Terminal Markings on Socket
Sockets
Certifications
Standards
–30…+55 °C
(–22…+131 °F)
–55…+85 °C
(–67…+185 °F)
2000 m (6560 ft)
Molded High Dielectric Material
Transparent Dust Cover
AgNi (700-HC2)
AgNi + 5 μm All (700-HC1)
In accordance with EN50 0005
700-HN103, -HN128, -HN104
cURus Recognized (File No. E14843, Guide NRNT2/NRNT8), cULus Listed when used with Bulletin 700HN103, -HN104, and -HN128 sockets (File No. E14843, Guide NRNT/NRNT7), CE Marked, LR Certified
UL 508, CSA 22.2 No. 14, EN 61810-1
‡ NEMA Rating Chart is in publication 700-SG003*
Rockwell Automation Publication 700-TD552A-EN-P
15
700-HC Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
37.2
(1.46)
36.7
(1.44)
5.6
(0.22)
6.1
(0.24)
20.7
(0.82)
27.7
(1.09)
20.7
(0.82)
27.7
(1.09)
Bulletin 700-HC Relay (Two-Pole)
Bulletin 700-HC Relay (Four-Pole)
27.0
(1.06)
60.9
(2.40)
21.5
(0.85)
35.6
(1.40)
76.0
(2.99)
3.2
(0.13)
18.9
(0.74)
34.9
(1.37)
32.0
(1.26)
35.5
(1.40)
2.5
(0.10)
Cat. No. 700-HN104
Single Wire: 0.2 mm2…2.5 mm2 (#24 AWG…14 AWG)
Double Wire: 2 x 0.2 mm2…2 x2.5 mm2 (2 x 24 AWG…2 x 14 AWG)
Wire Type: solid or stranded, copper only
Strip Length: 7 mm (9/32 in.), Torque: 0.5 N•m (4.4 lb•in)
30.0
(1-3/16)
6.1 (15/64)
Panel Mounting
28.9
(1-9/64)
24.5
(31/32)
8
7
6
5
4
3
2
1
24.9
(57/64)
21.1
(53/64)
67.0
(2-5/8)
4.2
(5/32)
#4-40
M3
30.0
(1-11/64)
14
12
13
11
10
62.0
(2-15/64)
65.0
(2-9/16)
9
26.0
(1-1/64)
16
Cat. No. 700-HN103
Cat. No. 700-HN128
Single Wire: 0.2 mm2…2.5 mm2 (#24 AWG…14 AWG)
Double Wire: 2 x 0.2 mm2…2 x 1.5 mm2 (2 x 24 AWG…2 x 16 AWG)
Wire Type: Solid or Stranded, Copper only
Strip Length: 8 mm (5/16 in.), Torque: 0.5 N•m (4.4 lb•in)
Wire Size: 2 x 1.5mm2 (#2-16 AWG…#1-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Toque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HK Relay
Cat. No. 700-HK…
Electrical Ratings
Rated Thermal Current ( Ith )
1-Pole, 1 CO, SPDT — 16 A
Rated Insulation Voltage (Ui)
120V AC
AC-15, 6.2 A
B300 Pilot Duty, 3 A
A300 (700-HKM_)
1/3 Hp (0.24 kW) 1-phase
120V AC
AC-15, 2.9 A
B300 Pilot Duty, 3.0 A
1/4 Hp (0.18 kW), 1-phase
240V AC
AC-15, 3.1 A
B300 Pilot Duty, 1.5 A
A300 (700-HKM_)
3/4 Hp (0.55 kW), 1-phase
240V AC
AC-15, 1.4 A
B300 Pilot Duty, 1.5 A
1/2 Hp (0.37 kW), 1-phase
230V AC
0.55 kW, 1-phase
230V AC
0.37 kW, 1-phase
24V DC
DC-13, 5.0 A
24V DC
DC-13, 3.0 A
125V DC
DC-13, 0.2 A
R300 Pilot Duty, 0.22 A
125V DC
DC-13, 0.2 A
R300 Pilot Duty, 0.22 A
250V DC
DC-13, 0.1 A
R300 Pilot Duty, 0.11 A
5 A, 250V
AC
DC-13, 0.1 A
R300 Pilot Duty, 0.11 A
230V AC
AC-1, 16 A
230V AC
AC-1, 8 A
277V AC
16 A, General Use
277V AC
8 A, General Use
30V DC
DC-1, 12 A
10 A, Resistive
30V DC
DC-1, 6 A
6 A, Resistive
Inductive V AC
Contacts
Inductive V DC
Resisitive
Make, Break &
Continuous
Min. Permissible Contact Ratings
Permissible Coil Voltage
Variation
Pickup:
holding Voltage:
Must Dropout Voltage:
2-Pole, 2 CO, DPDT — 8 A
250V IEC, 300V UL/CSA
300 mW (5V/60 mA or 60V/5 mA) for AgNi Contacts (700-HK3_)
50 mW (5V/10 mA or 25V/2 mA) for AgNi + Gold Contacts (700-HKX_)
500 mW (100V/5 mA or 5V/100 mA) for AgSnO2 Contacts (700-HKM_)
80…110% of Nominal Voltage at 50/60 Hz, 73...110% of Nominal Voltage at DC
80% of Nominal V AC at 50/60 Hz, 40% of Nominal V DC
20% of Nominal V AC at 50/60 Hz, 10% Nominal V DC
Power Consumption
1.2V A (V AC Coils), 0.5 W (V DC Coils)
Coil Voltages
See Overview/Product Selection
Design Specification/Test Requirements
Dielectric Withstand
Voltage
Pole to Pole (VRMS)
2000V AC
Contact to Coil (VRMS)
4000V AC
Degree of Protection
Mechanical
IP 20 (guarded terminal sockets), RT II — Flux-proof (Relay)
10 x 106
Mechanical Life Operations
Electrical Life Cycles
230V AC, 16 A Resistive: 100 000 min.
277V AC, 16 A Resistive: 30 000 min.
30V DC, 10 A Resisitive: 30 000 min.
B300, R300, Hp (kW): 6000 min.
A300 (700-HKM_): 100,000 min.
Mechanical: 18,000 cycles/hr.
Electrical: 900 cycles/hr.
Switching Frequency
Operating Time at
Nominal
Voltage at 20 °C (ms)
230V AC, 8 A Resistive: 100 000 min.
277V AC, 8 A Resistive: 30 000 min.
30V DC, 6 A Resistive: 30 000 min.
B300, R300, Hp (kW): 6000 min.
Pickup
Vibration
15 ms max.
Dropout
5 ms max.
Operational
10…2000 Hz, 0.76 mm (0.03 in.) 2.5 G
10…2000 Hz, 0.76 mm (0.03 in.) 5.0 G
Non-Operational
Shock
Operational
15 G
Non-Operational
50 G
Environmental
Operating
–40…+70 °C
(–40…+158 °F)
Storage
–40…+85 °C
(–40…+185 °F)
Temperature
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High Dielectric Material
Enclosure
Transparent Dust Cover
Contact Material
700-HK3_: Silver nickel (AgNi); 700-HKX_: Silver Nickel + Gold Plating (AgNi + Au); 700-HKM_: Silver Tin
Oxide (AgSnO2)
Terminal Markings on Socket
In accordance with EN 50005
1-Pole
2-Pole
Screw Terminal
700-HN121 (10 A @ 70 °C)
700-HN221 (16 A @ 50 °C, 12 A @ 70 °C)
700-HN122 (2 x 5 A @ 70 °C)
700-HN222 ( 2 x 8 A @ 70 °C)
Spring Clamp (Available
September 2006)
700-HN223 (15 A @ 40 °C with 2 conductors per
terminal)
(10 A @ 70 °C with 1 conductor per terminal)
700-HN224 (2 x 8 [email protected] 70 °C)
Sockets
Approvals
Rockwell Automation Publication 700-TD552A-EN-P
17
700-HK Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
12.4
(1/2)
29.0
(1-9/64)
12.4
(1/2)
29.0
(1-9/64)
32.8
(1-19/64)
32.8
(1-19/64)
30.1
(1-3/16)
6.5
(1/4)
6.5
(1/4)
2.5
(3/32)
4.75
(3/16)
0.5
(1/32)
A1
5
A2
1
A1
8
COM 11
4
NO 14
4
NC 12
2
0.5
(1/32)
COM 11
3
NC 12
2
A2 NC 22
1
7
NC 12 NO 14
2
3
COM 21
6
COM 11 NO 14 NC 12
3
4
2
A1
8
NO 24
5
NC 22
7
15.8
(5/8)
COM 21 NO 24 NC 22
6
5
7
A2
1
NO 14
3
NC 12
2
A2
1
Cat. No. 700-HN222
Cat. No. 700-HN224
COM 11
4
A1
5
COM 11 NO 14 NC 12
4
3
2
A1
5
15.8
(5/8)
15.8
(5/8)
A2
1
A2
1
Cat. No. 700-HN221
Cat. No. 700-HN223
64.9
(2-9/16)
44.7
(1-3/4)
18
NO 24
5
A1
8
15.8
(5/8)
COM 21
6
NO 14
4
Cat. No. 700-HK32_ (DPDT)
Cat. No. 700-HK36_ (SPDT)
COM 11
3
30.1
(1-3/16)
32.5
22.6 (1-9/32)
(57/64)
35.3
(1-25/64)
34.7
(1-3/8)
95.6
(3-49/64)
35.4
(1-13/32)
82.85
(3-17/64)
Cat. No. 700-HN223, 700-HN224
Wire Size: 0.2 mm2...1.5 mm2 (#24 AWG....#14 AWG)
Either Solid or Stranded
Strip Length: 8 mm (5/16 in)
Cat. No. 700-HN221, 700-HN222
Wire Size: 0.2 mm2...2.5 mm2 (#24 AWG....#12 AWG)
Either Solid or Stranded
Strip Length: 8 mm (5/16 in), Torque: 0.8Nm (7.0 lb.-in.)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HK Relay
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
46.0
(1-13/16)
14.4
(37/64)
3.6
(9/64)
14.4
(37/64)
38.0
(1-1/2)
46.9
(1-27/32)
42.4
(1-43/64)
36.6
(1-11/16)
39.8
(1-37/64)
18.1
(23/32)
2.0
(5/64)
34.8
(1-3/8)
Cat. No. 700-HN227
Cat. No. 700-HN226
1.0
(0.04)
12.5
6.2
(1/2)
(15/64)
50
(1-63/64)
27.0
(1.06)
35.0
(1.38)
5.2
(13/64)
7.5
(0.30)
1000
(39-3/8)
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
7.11
(9/32)
11
4
14
3
2.03
(5/64)
Five M3.5
x 0.315 Screws
4.06
(5/32)
12
2
3.0 Ø
(1/8)
Use M3 Screws
84.1
5 (+) (3-5/16)
(A1)
21
6
39.5
(1-17/32)
35.5
(1-13/32)
1 (-)
(A2)
4.06
(5/32)
15.6
(5/8)
29.9
(1-3/16)
54.1
(2-1/8)
7.11
(9/32)
11
3
22
7
24
5
Eight
M3.5 x 0.315
Screws
14
4
84.1
(3-5/16)
8 (+)
(A1)
4.06
(5/32)
2.03
(5/64)
12
2
4.06
(5/32)
39.5
(1-17/32)
3.0 Ø
(1/8)
Use M3 Screws
15.6
(5/8)
35.5
(1-13/32)
1 (-)
(A2)
29.9
(1-3/16)
54.1
(2-1/8)
Cat. No. 700-HN121
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #14 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Cat. No. 700-HN122
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #14 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Holes required for mounting [3 mm (1/8 in.) diameter].
Rockwell Automation Publication 700-TD552A-EN-P
19
700-HLT Relay
Relays and Timer Specifications
Cat. No. 700-HLT… (Relay Output)
Electrical Ratings
Pilot Duty Rating
B 300, R 300
Rated Thermal Current (Ith)
1-Pole — 6 A
Rated Insulation Voltage (Ui)
250V IEC, 300V UL/CSA
Inductive
Contacts
1-Pole
24V AC,
1-phase
30 A
5A
120V AC,
1-phase
30 A
3A
240V AC,
1-phase
15 A
1.5 A
Make, Break &
Continuous
V DC
1.0 A
0.2 A
240V DC
0.1 A
AC-15 250V, 3 A N.O. Contact, 1.5 A N.C. Contact
DC-13 24V, 1 A N.O. and N.C. Contact
Inductive Load
Min. Permissible Contact Ratings
12V, 6 mA (72 mW) for Silver Contacts, 8V, 2.5 mA (20 mW) for Gold Contacts
Pickup:
Must Dropout
10% of Nominal Voltage at AC
Voltage:
5% of Nominal Voltage at DC
85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Permissible Coil Voltage Variation
Power Consumption
±10%
24V DC
120V DC
AC
0.3 VA
DC
0.2 W
Design Specification/Test Requirements
Dielectric Withstand Voltage
Input Voltage
Impedance (Ohms)
Pole to Pole
(VRMS)
1000V
Contact to
Coil
(VRMS)
4000V
12V AC/DC
24V AC/DC
48V AC/DC
120V AC/DC
240V AC/DC
120V LCSC
240V LCSC
1K
2K
6K
26 K
56 K
16 K
35 K
Mechanical
Degree of Protection
IP20
1 x 107
Mechanical Life Operations
6 A Resistive: 100 000 min.
24V DC, 1 A Inductive: 200 000 min.
120V AC 1 A Inductive: 300 000 min.
Electrical Life Operations
Switching Frequency Operations (no-load)
10 cycles/sec
Coil Voltages
Operating Time at Nominal Voltage at 20 °C
(ms)
See Overview/Product Selection
Pickup
7 ms
Dropout
3 ms
Maximum Operating Rate (full load = 6 A)
6 cycles/min.
Per EN 61000-4.5; Surge Immunity (801-5)
Class III: 2 kV common and 1 kV differential mode
Coil Surge Protection
Environmental
Temperature
Operating
–40…+55 °C
Storage
–40…100 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High Dielectric Material
Enclosure
Relay IP67
Silver Tin Ox., AgSnO2 or Silver with Gold Plating, AgSnO2 + Au
Contact Material
Terminal Markings on Socket
Certifications
In accordance with EN50 0005
cULus Listed (File No. E3125, Guide NLDX/NLDX7) with Allen-Bradley socket, CE Marked, ABS (American
Bureau of Shipping)
Standards
EN 61810-1, CSA 22.2,UL 508,NEMA IEE MAC Compliant, ICS-2 Compliant
Class 1, Zn 2, Groups IIC, Ex nC IIC T5 Ta < 55 °C
Hazardous Location Approvals
20
UL Listed
(UL 60079-15)
700-HLT1Z12-EX (12V DC supply)
700-HLT1Z24-EX, 700-HLS1Z24-EX (24V DC supply)
700-HLT1U1-EX, 700-HLS1U1-EX (110V/125V AC/DC supply)
CSA Certified‡
(CAN/CSA
E60079-15)
700-HLT1Z12-EX (12V DC supply)
700-HLT1Z24-EX, 700-HLS1Z24-EX (24V DC supply)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HLS Relay
Cat. No. 700-HLS… (Solid State Output)
Electrical
Rated Thermal Current (Ith)
2 A (DC output)
Rated Insulation Voltage (Ui)
250V IEC, 300V UL/CSA
Control Circuit
Outputs
Power Consumption
±10%
1 A (AC output)
Min. Control Voltage
80% nominal voltage
Maximum Control Voltage
110% nominal voltage
Control Current
9 mA ±10% (24V) 4 mA ±10% (120/240V)
Release Voltage
0.4 x nominal voltage (24V), 0.35 x nominal voltage (120/240V)
Min. Control Circuit Resistance
3200 ohms (24V), 16k ohms (120V), 32k ohms
(240V)
2500 ohms (24V), 12k ohms
(120V), 24k ohms (240V)
24…240V AC
Load Voltage Range
0…24V DC
Max. Repetitive Blocking Voltage
33V
600V
Max. Switching Current
(inductive/resistive)
2 A DC
1 A AC
On State Voltage Drop @ Max.
Switching Current
<120 mV DC
<1V AC
Leakage Current
max. 100 μA (@U = 24V)
AC
0.6 VA (120V), 1 VA (240V)
DC
0.2 W
0.3 W
Design Specification/Test Requirements
Dielectric Withstand Voltage
Input Voltage
Impedance (Ohms)
Pole to Pole (VRMS)
2500V
Contact to Coil (VRMS)
2500V
24V DC
48V DC
120V AC/DC
240V AC/DC
120V LCSC
240V LCSC
2K
9K
26 K
58 K
16 K
35 K
Mechanical
Degree of Protection
IP20
Input Voltages
Operating Time at Nominal
Voltage at 20 °C (ms)
See Overview/Product Selection
Turn on Time
30 μs (DC only input voltage), 7 ms (AC/DC input voltage)
Drop Out Time
350 μs (DC only input voltage), 10 ms (AC/DC input voltage)
Maximum Operating Rate
300 Hz
Environmental
Temperature
Operating
–20…+55 °C
Storage
–40…70 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High-Dielectric Material
Enclosure
Relay IP67
Terminal Markings on Socket
Certifications
In accordance with EN50 0005
cULus Listed (File No. E14843, Guide NLDX/NLDX7), CE Marked, ABS (American Bureau of Shipping)
Standards
UL 508, CSA C22.2 No. 14, EN 61810-1
Class 1, Zn 2, Groups IIC, Ex nC IIC T5 Ta < 55 °C
Hazardous Location Approvals
UL Listed
(UL 60079-15)
700-HLT1Z24-EX, 700-HLS1Z24-EX (24V DC supply)
700-HLT1U1-EX, 700-HLS1U1-EX (110V/125V AC/DC supply)
CSA Certified
(CAN/CSA 60079-15)
700-HLT1Z24-EX, 700-HLS1Z24-EX (24V DC supply)
Product shall be installed in an enclosure providing at least IP54 protection. Provisions shall be made to prevent the rated voltage from being exceeded by
transient disturbances of more than 40%.
Rockwell Automation Publication 700-TD552A-EN-P
21
700-HL Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
76.0
(2.99)
76.0
(2.99)
93.0
(3.66)
88.0
(3.46)
6.2
(0.24)
6.2
(0.24)
Bulletin 700-HL Spring Terminal Design
Single Wire: 0.2 mm2…2.5 mm2 (#24 AWG…#14 AWG)
Wire Type: Solid or stranded, copper only
Strip Length: 9 mm (11/32 in.)
12.5
(1/2)
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
22
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HLT Relay
Cat. No. 700-HLT…2-Pole (Relay Output)
Electrical Ratings
Rated Thermal Current (Ith)
2-Pole — 10 A
Rated Insulation Voltage (Ui)
250V IEC, 300V UL/CSA
Inductive V AC
UL
Contacts
Inductive V
DC
Resistive
Make, Break
and
Continuous
Min. Permissible Contact Ratings
120V AC
AC-15, 3.0A
B 300, 3.0 A
1/4 HP (186 W), 1-phase
240V AC
AC-15, 3.0 A
B 300, 1.5 A
1/2 HP (373 W), 1-phase
24V DC
DC-13, 2.0 A
125V DC
DC-13, 0.3 A
250V DC
DC-13, 0.2 A
250V AC
10 A
24V DC
10 A
250V DC
0.28 A
12V, 10 mA (120 mW) for Silver Contacts, 5V, 1 mA (50 mW) for Gold Contacts
Pickup:
Permissible Coil Voltage Variation
85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Must Dropout
Voltage:
10% of
Nominal
Voltage at AC
5% of
Nominal
Voltage at DC
Design Specification/Test Requirements
Dielectric Withstand Voltage
Input Voltage
±10%
1000V
Contact to
Coil
(VRMS)
5000V
Adjacent
Contacts
(VRMS)
2500V
12V AC/DC
24V AC/DC
48V DC
120V AC/DC
1K
2K
3K
34 K
72 K
AC
N/A
0.5V A
N/A
0.4V A
0.8V A
DC
0.4 W
0.5 W
0.8 W
0.5 W
0.7 W
Impedance (Ohms)
Power Consumption
Pole to Pole
(VRMS)
240V AC/DC
Mechanical
Degree of Protection
IP20
3 x 107
Mechanical Life Operations
250V AC/24V DC, 8 A Resistive: 100 000 min.
24V DC, 10 A Resistive: 6000 min.
Electrical Life Operations
250V DC, 0.28 A Resistive: 6000 min.
250V AC, 10 A Resistive: 30 000 min.
Switching Frequency Operations (no-load)
1200 cycles/sec
Coil Voltages
Operating Time at Nominal Voltage at 20 °C (ms)
See Overview/Product Selection
Pickup
typical 10 ms
Dropout
typical 10 ms
Maximum Operating Rate (full load = 6 A)
6 cycles/min.
Environmental
Temperature
Operating
–40…+60 °C
Storage
–40…+100 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Enclosure
Contact Material
Terminal Markings on Socket
Certifications
Standards
Molded High-Dielectric Material
Relay RT II — flux-proof, pollution degree 2 installation environment
AgNi 90/10 or AgNi 90/10 + Au
In accordance with EN50 0005
cULus Listed (File No. E3125, Guide NRNT/NRNT7), CE Marked
UL 508, CSA C22.2 No. 14, EN 61810-1
Rockwell Automation Publication 700-TD552A-EN-P
23
700 Interposing Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate dimensions are shown in millimeters (inches). Approximate dimensions are not intended to be used for manufacturing purposes.
92.8
(3.65)
87.7
(3.45)
14
(0.55)
14
(0.55)
75
(2.95)
75
(2.95)
Bulletin 700-HL Screw Terminal Design
Single Wire: 0.14 mm2…2.5 mm2 (#26 AWG…14 AWG)
Double Wire: 2 x 0.14 mm2…2 x 1.5 mm2 (2 x #26 AWG…2 x 16 AWG)
Wire Type: Solid or stranded, copper only
Strip Length: 9 mm (11/32 in). Torque: 0.5 N•m (4.4 lb•in)
Bulletin 700-HL Spring Terminal Design
Single Wire: 0.2 mm2…2.5 mm2 (#24 AWG…#14 AWG)
Wire Type: Solid or stranded, copper only
Strip Length: 9 mm (11/32 in)
97.8
(3.85)
Bulletin 700-TBJ08_ 8-Way Jumper
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
24
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700 Interposing Relays
Function and Connection Diagrams
On-Delay
15
A1
U (A1/A2)
1 c/o (SPST)
t
R
LED
A2
18 16
One Shot
15
A1
U (A1/A2)
t
U (A1/A2)
1 c/o (SPST)
R
t
R
1 c/o15
(SPST)
A1
LED
t
t
A2
LED
18 16
A2
18 16
Pulse
A1
15
U (A1/A2)
1 c/o (SPST)
t
R
0.5s
LED
A2
18 16
Flasher
Rockwell Automation Publication 700-TD552A-EN-P
25
700-HLF Relay
Relays and Timer Specifications
Specifications
Cat. No. 700-HLF… (Relay Output)
Electrical Ratings
Pilot Duty Rating
B 300, R 300
Rated Thermal Current (Ith)
1-Pole — 6 A
Rated Insulation Voltage (Ui)
250V IEC, 300V UL/CSA
Inductive
Contacts
1-Pole
24V AC,
1-phase
30 A
5A
120V AC,
1-phase
30 A
3A
240V AC,
1-phase
15 A
1.5 A
Make, Break &
Continuous
V DC
1.0 A
0.2 A
240V DC
0.1 A
AC-15 250V, 3 A N.O. Contact, 1.5 A N.C. Contact
DC-13 24V, 1 A N.O. and N.C. Contact
Inductive Load
Min. Permissible Contact Ratings
12V, 6 mA (72 mW) for Silver Contacts, 8V, 2.5 mA (20 mW) for Gold Contacts
Pickup:
85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Permissible Coil Voltage Variation
Power Consumption
±10%
24V DC
120V DC
AC/DC
Must Dropout
Voltage:
10% of Nominal
Voltage at AC
5% of Nominal
Voltage at DC
0.5 VA
Design Specification/Test Requirements
Dielectric Withstand Voltage
Pole to Pole
(VRMS)
1000V
Contact to Coil
(VRMS)
4000V
Input Voltage
24V AC/DC
Impedance (Ohms)
2K
Mechanical
Degree of Protection
IP20
1 x 107
Mechanical Life Operations
6 A Resistive: 100 000 min.
24V DC, 1 A Inductive: 200 000 min.
120V AC 1 A Inductive: 300 000 min.
Electrical Life Operations
Switching Frequency Operations (no-load)
10 cycles/sec
Coil Voltages
See Overview/Product Selection
Timer Functions
On-Delay, One Shot, Pulse and Flasher
Timer Settings
0.1...3 s, 3...60 s, 1...20 min, and 0.3...6 hr
Timer Adjustments
Min and Max adjustments with Potentionmeter
Timer Accuracy
Repeatability 1%, Recovery Time < 50 ms, Setting Accuracy Full Range 5%
Per EN 61000-4.5; Surge Immunity (801-5)
Class III: 2 kV common and 1 kV differential mode
Coil Surge Protection
Environmental
Temperature
Operating
–40…55 °C
Storage
–40…100 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Enclosure
Contact Material
Terminal Markings on Socket
Molded High Dielectric Material
Relay IP67
Silver Tin Ox., AgSnO2 or Silver with Gold Plating, AgSnO2 + Au
In accordance with EN50 0005
Certifications
cULus Listed (File No. E3125, Guide NLDX/NLDX7) with Allen-Bradley socket, CE Marked
Standards
EN60947-4-1,EN60947-5-1,CSA 22.2,UL 508,NEMA IEE MAC Compliant, ICS-2 Compliant
‡ Product shall be installed in an enclosure providing at least IP54 protection. Provisions shall be made to prevent the rated voltage from being exceeded by
transient disturbances of more than 40%.
26
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HLF
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
76.0
(2.99)
6.20
(0.24)
88.0
(3.46)
Bulletin 700-HLF Screw Terminal Design
Single Wire: 0.14 mm2…2.5 mm2 (#26 AWG…14 AWG)
Double Wire: 2 x 0.14 mm2…2 x 1.5 mm2 (2 x #26 AWG…2 x 16 AWG)
Wire Type: Solid or stranded, copper only
Strip Length: 9 mm (11/32 in.). Torque: 0.5 N•m (4.4 lb•in)
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
Bulletin 700-HP Pin Style (PCB) Slim Line Relay, Socket, and Retainer Clip Reference Chart
Relay Type
Socket Cat. No.
700-HPX2
700-HN123
Retainer Clip Cat. No.
700-HN119
700-HP32
700-HN123
700-HN119
700-HPS2
700-HN123
700-HN119
700-HPSX
700-HN123
700-HN119
Rockwell Automation Publication 700-TD552A-EN-P
27
700-HP Relay
Specifications
Relays and Timer Specifications
1
Cat. No. 700-HP…
Cat. No. 700-HP3…, 700-HPX
Cat. No. 700-HPS…
AC 15 @ 500V AC
V AC
C300
B300
1/3 Hp @ 240V AC
1/2 Hp @ 240V AC
1/6 Hp @ 120V AC
1/3 Hp @ 120V AC
AC-1 2000VA
Inductive
⎯
R300
Contacts
V DC
DC-1: 8A @ 30V DC
DC-1: 0.3A @ 110V DC
DC-1: 0.65A @ 110V DC
DC-1: 0.1A @ 220V DC
DC-1: 0.2A @ 220V DC
AC
Resistive
8 A @ 277V AC (per pole)
DC
8 A @ 30V DC (per pole)
700-HPS2: 500 mW (10V, 10
mA)
700-HPSX: 50 mW (5V, 5 mA)
700-HP32: 300mW (5V, 5 mA)
700-HPX2: 50mW (5V, 5 mA)
Minimum Load
Nominal Coil Power (AC/DC)
1.2 VA / 0.65 W
0.7 W
Operating Range (AC/DC)
80...110% / 73...150%
Nominal Voltage
75...120% Nominal Voltage
DC
Holding Voltage (AC/DC)
80 / 40% Nominal Voltage
40% Nominal Voltage DC
Must Drop Out Voltage (AC/DC)
20 / 10% Nominal Voltage
10% Nominal Voltage DC
Insulation Voltage
250V AC
Design Specification/Test Requirements
Dielectric Withstand Voltage
for one minute
700-HP3, 700-HPX
Pole to Pole (VRMS)
700-HPS
2000V AC
Contact to Coil (VRMS)
4000V AC
Mechanical
Degree of Protection
Open Type (Sockets)
Mechanical Life Cycles
Switching Frequency Operations
10 x 106 (AC Coils), 20 x 106
(DC coils)
10 x 106 (DC Coils)
1800/hr (no load)
900/hr (no load)
Coil Voltages
Operating Time at Nominal
Voltage at 20 °C (ms)
See Overview/Product Selection
Pickup
12
4
Maximum Operating Rate
Vibration
Shock
10
Dropout
16 Ops/s (full load)
8 Ops/s (full load)
Enclosure
5G
Fragility
2.5 G
Endurance
50 G
Fragility
15 G
Max. Socket Torque
0.5 N•m (4.4 lb•in)
Environmental
Temperature
Operating
–40…+85 °C
–40…+70 °C
Storage
–45…+100 °C
–50…+80 °C
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High-Dielectric Material
Enclosure
Transparent Dust Cover
Red Transparent Dust Cover
Silver Nickel, (AgNi) (700-HP32 and 700-HPS2), Silver Nickel +
Gold Plating (AgNi + Au) (700-HPX2 and 700-HPSX)
Contact Material
Terminal Markings on Socket
In accordance with EN50 0005
2-Pole
Sockets
700-HN123
Approvals
Certifications
Standards
cURus Recognized (File No. E3125, Guide NLDX2/NLDX8),
cULus Listed when used with Bulletin 700-HN123 socket (File
No. E3125, Guide NLDX/NLDC7), CSA Certified (files 229473),
CE Marked, LR Certified (700-HP), IMQ & TUV Certified (700HPS)
UL 508, CSA 22.2 No. 14, EN 61810-1, EN 50205 (700-HPS)
‡ NEMA Rating Chart is in publication 700-SG003*
§ The inrush VA equals 1.5 times the sealed VA.
28
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HP Relay
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
29.0
(1.14)
12.4
(0.49)
25.0
(0.98)
Bulletin 700-HP Relay
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 700-HN123
Single Wire: 0.2.....2.5 mm2 (#24.....14 AWG)
Double Wire: 2 X 0.2.....2 X 2.5 mm2 (#2 X 24....2 X 14 AWG)
Wire Type: solid or stranded, copper only
Strip Length: 7 mm (9/32 in.), Torque: 0.5 N•m (4.4 lb•in)
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lb) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lb) (5/pkg)
Rockwell Automation Publication 700-TD552A-EN-P
29
700 Interposing Relays
Relays and Timer Specifications
21
6
11
3
24
5
14
4
22
7
12
2
17.5
(0.69)
60.9
(2.40)
17.5
(0.69)
21.6
(0.85)
Ø 3.2
(0.12)
Use M3 Screws
78.6
(3.09)
8 (+)
A1
1 (-)
A2
4.0
(0.16)
15.8
(0.62)
Cat. No. 700-HN123
Single Wire: 0.2.....2.5 mm2 (#24.....14 AWG)
Double Wire: 2 X 0.2.....2 X 2.5 mm2 (#2 X 24....2 X 14 AWG)
Wire Type: solid or stranded, copper only
Strip Length: 7 mm (9/32 in.), Torque: 0.5 N•m (4.4 lb•in)
30
Rockwell Automation Publication 700-TD552A-EN-P
35.4
(1.39)
21.6
(0.85)
Relays and Timer Specifications
700-HJ Magnetic Latching Relays
Specifications
Cat. No. 700-HJ…
Electrical Ratings
Pilot Duty Rating
—
th
Rated Thermal Current (I )
10 A
Rated Insulation Voltage (Ui)
250V IEC,
300V UL/CSA
Inductive
120V AC
240V AC
Contacts
Make
Break
Hp
30 A
15 A
3A
1.5 A
1/4
1/3
DC
24V DC, 10 A
85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Permissible Coil
Voltage Variation
AC Coils
Coil Consumption ±10%
Inrush
Sealed
DC Coils
Single
AC Coil
Single
DC Coil
Dual
DC Coil
1.44 VA
1.44 VA
—
—
—
1.2 W
12V 1.63 W
24V 1.67 W
Design Specification/Test Requirements
Dielectric
Withstand
Voltage
Pole-to-Pole
1500V AC
Contact-to-Pole
1500V AC
Contact-to-Frame
1500V AC
Mechanical
Open Type
(Guarded Terminal Sockets)
Degree of Protection
Mechanical Life Operations
10 x 106
Switching Frequency
Operations
1800/HR
Coil Voltages
See Product Selection
Operating Time at Nominal Voltage at 20 °C
Pickup
Dropout
25 ms
25 ms
Maximum Operating Rate
—
Environmental
Operating
–45…+50 °C
(–49…+122 °F)
Storage
–45…+100 °C
(–49…+212 °F)
Temperature
Altitude
2000 m (6560 ft.)
Construction
Insulating Material
Enclosure
Contact Material
Terminal Markings on Socket
Sockets
Certifications
Standards
Molded High
Dielectric Material
Transparent Dust Cover
Silver Cad. Ox.
In accordance with EN50 0005
11-Blade Socket
Cat. No. 700-HN153
Cat. No. 700-HN154
CSA Certified, File LR700026, UL Recognized, File E3125, Guide NLDX 2
UL 508, CSA 22.2 No. 14, EN/IEC 60947-4-1, -5-1
Rockwell Automation Publication 700-TD552A-EN-P
31
700-HJ Magnetic Latching Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
Bulletin 700-HJ Relay
Cat. No. 700-HN153
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) – Torque: 0.8 N•m (7 lb•in)
Cat. No. 700-HN154
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) – Torque: 0.8 N•m (7 lb•in)
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
32
Cat. No.
A
B
C
D
Approx.
Shipping Wt.
199-DR1
35
(1-3/8)
27
(1-1/16)
7.5
(19/64)
1.02
(1/64)
1.85 kg
(4.07 lbs.) (10/pkg)
199-DR4
35
(1-3/8)
27
(1-1/16)
15
(19/32)
2.3
(3/32)
3.68 kg
(8 lbs.) (5/pkg)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HG Power Relays
Specifications
Cat. No. 700-HG...
Electrical Ratings
Pilot Duty Rating ‡
A600
Rated Thermal Current (/th)
40 A
Rated Insulation Voltage (Ui)
600V UL
Contact Ratings: AC Ratings SPST-NO-DM
Contact Ratings: AC Ratings SPDT, DPST - NO and DPDT
Inductive
Volts
Resistive Make/Break
HP Volts
and
Continuous
Continuous
Make
Break
120
60 A
6A
10 A
40 A
240
30 A
3A
10 A
40 A
480
15 A
1.5 A
10 A
12 A
600
12 A
1.2 A
10 A
10 A
DC Ratings: Without Magnetic Blowouts - 28V 40 A - Make, Break and Continuous
2
Make
Break
Resistive Make/Break
and
Continuous
Continuous
120
60 A
6A
10 A
40 A
240
30 A
3A
10 A
40 A
480
15 A
1.5 A
10 A
5A
600
12 A
1.2 A
10 A
5A
HP§
1 - 1/2
1 - 1/2
Est Drop 125V 1.2...3 A
SPST - NO
- DM
SPDT, DPST - NO and DPDT
110V
20 A
10 A
220V
8A
4A
325V
4A
2A
500V
2A
DC Ratings: With Magnetic Blowouts:
Make, Break
and Continuous
2
Inductive
—
80...100% of Nominal Voltage at 50 Hz
Permissible Coil
Voltage Variation
85...110% of Nominal Voltage at 60 Hz
80...110% of Nominal Voltage at DC
50 HZ
Coil
Consumption
±10%
AC Coils
60 HZ
Inrush
13 VA
16 VA
Sealed
10 VA
11 VA
DC Coils
2.0 W
Design Specification/Test Requirements
Dielectric
Withstand
Voltage
Pole-to-Pole
2200V AC
Contact to Pole
2200V
Contact to Frame
2200V AC
Mechanical
Degree of Protection
Open Type
5 x 106
Mechanical Life Operations
Switching Frequency Operations
1600/Hr
Coil Voltage
Operating Time at Nominal
Voltage at 20 °C
See Overview/Product Selection
Pickup
Dropout
40 ms
35 ms
Maximum Operating Rate
—
Environmental
-30...+55 °C
Operating
(-22...+149 °F)
Temperature
-30...+65 °C
Storage
(-22...+149 °F)
Altitude
2000 m (6560 ft.)
Construction
Molded Thermo
Insulating Material
Setting Plastic
Enclosure
—
Contact Material
Silver Cadmium Oxide
Terminal Markings on Socket
—
Sockets
Certifications
N/A
CSA Certified, File 225674, UL Listed, File E3125, Guide NLDX, CE Marked
Standards
UL 508, CSA 22.2 No. 14, EN/IEC 60947-1, -5-1
‡ NEMA Rating Chart is on page 19 of publication 700-SG003B-EN-P.
§ For DPDT only: 2 Hp Switching 2 Poles, 200...600V AV, 50/60 Hz.
Rockwell Automation Publication 700-TD552A-EN-P
33
700-HG Power Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
Bulletin 700-HG Relays, SPST-NO-DM
Bulletin 700-HG Relays
34
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HHF Flange Mount Power Relays
Specifications
Cat. No. 700-HHF…
Electrical Ratings
SPST-NO-DM
NEMA A600
DPDT
NEMA B600
Pilot Duty Rating‡
3PDT
NEMA B300
th
Rated Thermal Current (I )
SPST-NO-DM 30 A, DPDT 25A, 3PDT 20 A
Rated Insulation Voltage (Ui)
Inductive
Contacts
250V IEC-300V UL/CSA
SPST-NO-DM
Hp
DPDT
Hp
3PDT
Hp
120V AC
60 A
6A
1
30 A
3A
1
30 A
3A
1/2
240V AC
30 A
3.0 A
1-1/2
15 A
1.5 A
1-1/2
15 A
1.5 A
—
DC
28V DC, 30 A
28V DC, 13 A
—
85…110% of Nominal Voltage at 50 Hz
Permissible Coil
Voltage Variation
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
SPST-NO-DM
Coil
Consumption
±10%
AC Coils
DPDT
3PDT
50 Hz
60 Hz
50 Hz
60 Hz
50 Hz
60 Hz
Inrush
7.2 VA
6.3 VA
7.2 VA
6.3 VA
7.2 VA
6.3 VA
Sealed
4.8 VA
4.2 VA
4.8 VA
4.2 VA
4.8 VA
4.2 VA
DC Coils
1.4 W
25% of VA
Max. Allowable Leakage
10% of W
Design Specification/Test Requirements
Dielectric Withstand
Voltage
Pole-to-Pole
2200V AC
Contact-to-Pole
2200V AC
Contact-to-Frame
1600V AC
Mechanical
Mechanical Life Operations
5 x 106
Switching Frequency Operations
3600/Hr
Coil Voltages
See Overview/Product Selection
Pickup
Operating Time at
Nominal Voltage at 20 °C Dropout
20 ms
15 ms
Maximum Operating Rate
4 Ops/s.
Environmental
–30…+50 °C
Operating
(–22…+122 °F)
Temperature
–30…+100 °C
Storage
(–22…+212 °F)
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Enclosure
Contact Material
Terminal Markings
Sockets
Certifications
Standards
Molded High Dielectric Material
Transparent Dust Cover
Silver Cadmium Oxide
In accordance with EN50 0005
§
cURus Recognized, File E3125,Guide NLDX2/NLDX8, CE Marked
UL 508, CSA 22.2 No.14, EN/IEC 60947-1, -5-1
‡ NEMA Rating Chart is in 700-SG003_-EN-P.
§ Bulletin 700-HHF relay wiring and terminals are the quick connect/solder type 6.35 x 0.82 mm (0.250 x 0.032 in) termination.
Rockwell Automation Publication 700-TD552A-EN-P
35
700-HHF Flange Mount Power Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
35.7
(1-13/32)
3.97
(5/32)
63.5
(2-1/2)
38.9
(1-17/32)
73.8
(2-29/32)
Bulletin 700-HHF Relays
36
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HTA - Alternating Relays
Specifications
Cat. No. 700-HTA…
Electrical Ratings
Pilot Duty Rating‡
NEMA B300 AC 15
th
Rated Thermal Current (I )
10 A
Rated Insulation Voltage (Ui)
250V IEC, 300V UL/CSA
Contacts
Inductive
Make
Break
120V AC
30 A
3A
1/3
240V AC
15 A
1.5 A
1/2
Resistive 30V DC
10 A
10 A
—
85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
Permissible Coil Voltage Variation
Power Consumption
±10%
HP
AC
24V AC
2 VA
120V AC
4 VA
240V AC
4 VA
Design Specification/Test Requirements
Dielectric Withstand Voltage
Pole-to-Pole, same
circuit (VRMS)
1000V AC
Pole-to-Pole, different
circuits (VRMS)
2000V AC
Contact-to-Coil (VRMS)
2000V AC
Electrical Life Operations
100,000 minimum
Switching Frequency Operations
1800/hr
Coil Voltages
See product selection
Mechanical
Degree of Protection
Open Type (Guarded Terminal Sockets)
Mechanical Life Operations
10 x 106
Switching Frequency Operations
18,000/hr
Start-up Time (max. time from power application until unit is timing)
0.05 sec
Max. Function Time (max. time power can drop out and unit continues timing)
0.01 sec
Min. Cycle Time
100 ms on release of the control switch
Environmental
Operating
–28…+65 °C (50 °C max., 240V AC coil)
(–18…+149 °F) (122 °F max., 240V AC coil)
Storage
–55…+85 °C
(–67…+185 °F)
Temperature
Altitude
2000 m (6560 ft)
Construction
Insulating Material
Molded High Dielectric Material
Enclosure
Impact Resistant Dust Cover
Contact Material
Silver Tin Oxide
Terminal Markings on Socket
In accordance with EN50 005
8- or 11-Pin Socket
700-HN100, -HN125
700-HN101, -HN126
Sockets
CSA Certified, File 223833, UL Recognized (File E3125 Guide NLDX2/NLDX8),
cULus Listed with 700-HN100, 700-HN101, 700-HN125, and 700-HN126
Sockets (File No. E3125 Guide NLDX/NLDX7), CE-Marked (per EU Low Voltage
Directive)
Certifications
Standards
EN 61812-1, EN/IEC 60947-1, -5-1, CSA 22.2 No. 14, UL 508
‡ NEMA Rating Chart is in publication 700-SG003_-EN-P.
Rockwell Automation Publication 700-TD552A-EN-P
37
700-HTA - Alternating Relays
Relays and Timer Specifications
Trigger Signal Cat. Nos. 700-HTA
Contact closure provides signal to timer. A low energy signal is generated by the 700-HTA alternating relay. For optimum reliability, use
contacts designed for low energy switching (10V, 1 mA) (Example: Bul. 800F-X__V, 800T-X__V). No external voltage should be connected to
the contact signal.
Load Diagrams
Common Input/Output SPDT/DPDT
Cross Wired
B1
Lead/Lag/Lag/lead Sequence
Lead
Load A
Lag
Load B
Load A
LED A
Load B
LED B
LED A
Power
LED B
Power
Socket
Pinout Map
SPDT
Relay Socket
Socket
Pinout Map
DPDT
Relay Socket
A1
4
A1
4
A2
3
A2
8
Note: pin out in wiring diagram may not match actual printed
socket see pinout map for wiring up the power source
Socket
Pinout Map
Cross-Wired
Relay Socket
A1
3
A2
6
Note: pin out in wiring diagram may not match actual printed
socket see pinout map for wiring up the power source
38
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HTA - Alternating Relays
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
79
(3-7/64)
74
(2-29/32)
60
(2-23/64)
(1-11/16)
24.6
(31/32)
40.1
(1-37/64)
30.0
(1-3/16)
20.8
(53/64)
26
(1-1/32)
24.9
(63/64)
65.0
(2-35/64)
54.9
(2-5/32)
4.2
(5/32)
51.1
(2-1/64)
38.0
(1-1/2)
#4–40
M3
33.0
(1-19/64)
14.7
(37/64)
Cat. No. 700-HN125
Cat. No. 700-HN100
Panel Mounting
Double Wire — 2 x 2.5 mm2 (#2 – 14 AWG…#2 – 20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) – Torque: 0.8 N•m (7 lb•in)
Wire Size: 2 x 2.5 mm2
Single Wire — Up to #12 AWG
Double Wire — 2 x 2.5 mm2 (#2 – 14 AWG… #2 – 20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) — Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
39
700-HTA - Alternating Relays
Relays and Timer Specifications
59.2
(2-1/3)
30
(1-3/16)
7.9
(0.31)
26
(1-1/32)
24.6
(31/32)
20.8
(53/64)
26.9
(1.06)
54.9
(2-5/32)
65.0
(2-35/64)
4.2
(5/32)
38.0
(1-1/2)
52.3
(2.06)
#4-40
M3
Cat. No. 700-HN101
Panel Mounting
Double Wire – 2 x 2.5 mm2 (#2 – 14 AWG…#2 – 20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) – Torque: 0.8 N•m (7 lb•in)
40
51.1
(2-1/64)
Cat. No. 700-HN126
Wire Size: 2 x 2.5 mm2
Single Wire — Up to 12 AWG
Double Wire — 2 x 2.5 mm2 (#2 – 14 AWG…#2 – 20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) — Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-FE DIN Rail Mounted Timing Relay
Function and Connection Diagrams
(A) On-Delay
A1/A2
U
Output
(B) Off-Delay
A1/A3
15
18
15
t
LED
A1/A2
U
A2
18
1 N.O. (SPST)
Output
LED
t
B1 S
A1
A1/B1
18
15
S
15
A2
18
A1 B1 S
15
A2
18 16
1 N.O. (SPST)
U
Output
LED
A1/A2
18
15 16
t
15
A1
S
A2
18 16
(D) One Shot
Output
15 18
16
t
1 C/O (SPDT)
(F) Flasher (Repeat Cycle Starting with Pulse)
A1/A2
15
t
15
A1
18
A2
18
A1
15
1 N.O. (SPST)
U
Output
LED
A1/B1
LED
1 C/O (SPDT)
U
Output
LED
A1/A2
U
A1/A2
A1/A2
A1
15
A2
18
A1
15
A2
18 16
18
t t t t t 15
LED
1 N.O. (SPST)
18
1516
t
U
Output
A2
18 16
U
Output
A1/A2
t
t
t
t
15 18
16
t
LED
1 C/O (SPDT)
1 C/O (SPDT)
(L) Pulse Converter
(E) Fleeting Off-Delay
LED
1)
1)
A1/A2
B1
S
A1 B1
15
t
A2
18 16
A1/A2
A1/B1
U
S
Output
LED
t
t
A1
S
B1
15
18
15 16
A2
18 16
1 C/O (SPDT)
(Y) Star-Delta Timing Relay
U
A1/A2
A1
17
A2
18 28
17/18
ţ
LED
tu = 50...65 ms
17/28
ţ
Bi-Color LED: 1 C/O (SPDT) or 1 N.O. Contact Timers
Single Color LED: 2 N.O. with Common
LED U = green: Supply voltage available.
LED Relay = red: Output is energized.
Rockwell Automation Publication 700-TD552A-EN-P
ON = green
OFF = red
41
700-FE DIN Rail Mounted Timing Relay
Relays and Timer Specifications
Specifications
Time Characteristics (according to VDE 0435, part 2021)
1 N.O.
Setting Accuracy
SPDT
±5% of full scale
Repeatability
±1% of setting (typical)
By voltage: ±0.01%/%ΔU
By temperature: ±0.25%/°C
Tolerance
By voltage: ±0.001%/%ΔU
By temperature: ±0.025%/°C
Supply
Supply Voltage
24V AC/DC‡ and 110…240V AC, 50/60 Hz
AC
Voltage Tolerance
24…48V DC and 24…240V AC, 50/60 Hz
–15%/+10%
DC
–15%/+20%
Power Consumption
0.5 W at 24V DC, 5 VA at 240V AC
Time Energized
100%
Reset Time
100 ms
Cable Length (Supply Voltage Control)
Max. 250 m (750 feet)
Pulse Control (B1)
≥ 250 ms
Impulse Duration
≥ 50 ms (AC), ≥ 30 ms (DC)
Input Voltage
supply voltage range
Input Current
1 mA
Cable Length
Max. 250 m without parallel load between B1 and A2
Max. 50 m with load (< 3 kΩ) between B1 and A2
Outputs
Contact Type
Dielectric Withstand
Voltage
Switching Capacity
1 N.O. contact
Contact-to-coil
4000 V
Power
1250 VA
According to IEC 947-5-1
AC-1
5 A /250V AC (resistive load)
AC-14
1 A/250V AC (inductive load)
DC-13
According to UL 508
Short-Circuit Resistance
Life
1 Form C – SPDT contact
1 A/24V DC (inductive load)
NEMA D300 - 1 A/300V AC
6 A gL (Fast Blow Fuse)
Mechanical
20 million operations
Electrical
0.4 million at 1 A/250V AC, resistive
0.4 million at 0.5 A/250V AC, cos φ = 0.4
0.4 million at 1 A/24V DC, resistive
State Indicator
Certifications
Standards
1 Bi-Color LED (Supply; Relay)
cULus Listed (File No. E14840, Guide NKCR/NKCR7), CE Marked
EN/IEC 60947-1, EN/IEC 60947-5-1, UL 508, CSA 22.2 No. 14
‡ Voltage is either 24V DC or AC 50/60 Hz.
42
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-FE DIN Rail Mounted Timing Relay
General Specifications
1 N.O.
Insulation Characteristics
The following requirements are fulfilled:
Surge capacity of the supply voltage
according to IEC 61000-4-5: Level 3
Burst according to IEC 61000-4-4: Level 3
ESD discharge according to IEC 61000-4-2: Level 3
EMC/Interference Immunity
EMC/Emmission
electromagnetical fields according to EN 55 022: Class B
Safe Isolation
Climatic Withstand
Vibration Resistance
according to VDE 0106 T 101
56 cycles (24 hr) at 25…40 °C and 95% relative humidity according to IEC 60068-2-30
4 g in three axes at 10…500 Hz, test FC according to IEC 60068-2-6
Shock Resistance
50 g according to IEC 68-2-27
Protection Class
IEC 60947-1
Weight
Certifications
Ambient Temperature
Connections
SPDT
2 kV AC/50 Hz test voltage according to VDE 0435
and 4 kV 1.2/50 μs surge voltage according to IEC 60947-1 between all inputs and outputs
Enclosure:IP 40
Terminal:IP 20
60 g
60 g
cULus, CE Certified
cULus, Germanischer Lloyd, CE Certified
Open:–25…+60 °C
Enclosed:–25…+45 °C
Storage:–40…+85 °C
Screw terminal M3 for Pozidriv No.1, Philips and slotted screws No.2. suitable for power screw-driver.
Rated tightening torque 8.8 lb.-in. (max. 1.0 Nm)
For terminal cross-sections of 1 x 0.5 mm2…2 x 1.5 mm2 (solid) or 2 x 1.5 mm2 (stranded with sleeve), #20…14 AWG.
Finger protection according to EN 50274
Mounting
For surface mounting in any position; snap-on mounting on 35 mm DIN Rail or by adapter and two screws (M4 type)
Disposal
Synthetic materials without dioxin according to EC/EFTA-Notification No. 93/0141/D
electrical contacts are AgCdO
Rockwell Automation Publication 700-TD552A-EN-P
43
700-FE DIN Rail Mounted Timing Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
80.0
(3-5/32)
13
(0.51)
22.5
(0.89)
43.0
(1-11/16)
4.3
(0.17)
45.0
(1-25/32)
35.0
(1.38) 58.0
(2.28)
17
12
(0.67) (0.47)
17.5
(11/16)
66.0
(2-9/16)
70.0
(2-49/64)
4.3
(0.17)
9.0
(0.35)
Cat. No. 700-FE…
44
Rockwell Automation Publication 700-TD552A-EN-P
2.0
(0.08)
5.5
(0.22)
Cat. No. 199-FSA…
75.0
(2.95)
Relays and Timer Specifications
700-FS DIN Rail Mounted Timing Relay
Connection Diagrams
(A) On-Delay
(G) Flasher (Repeat Cycle Starts with Pause)
Output
Output
Output
Output 1
Output 2
Output 2
(I) On-Delay Pulse Generator
(B) Off-Delay (Min. Pulse AC 50 ms…DC 30 ms)
Output
LED
Output
‡
Output 1
(J) On-Delay (Pulse Controlled)
Output 2
Output 2
(C) On- and Off-Delay
Output
LED
(K) One Shot/Watch Dog (Pulse Controlled)
Output
LED
‡
(D) One Shot
Output
LED
Output
(On) ON-Function (Off) OFF-Function
Output 1
Output 1
Output 2
Output 2
LED
LED
(E) Fleeting Off-Delay (Min. Pulse AC 50 ms…DC 30 ms)
(L) Pulse Converter (Min. Pulse AC 50 ms…DC 30 ms)
Output
t
LED
‡
Output
LED
‡
(F) Flasher (Repeat Cycle Starts with Pulse)
Cleverly Designed Function Display LED (Green)
Output
Output in Rest Position, No Timing
Output in Rest Position, Time Running
Output in Operation Position, No Time Running
Output in Operation Position, Time Running
* A VOLTAGE OTHER THAN THE SUPPLY VOLTAGE CAN BE USED AT
B1, BUT MUST BE WITHIN VOLTAGES SPECIFIED ON TIMER.
A voltage other than the supply voltage can be used at B1, but must be within voltages specified on timer.
† Output 2 is selectable as instantaneous contact with sliding switch (⊗) on front panel (instantaneous when switch is down, timed when switch is up).
‡ Available on multifunction "M," and single function "A" or "B" option timing relays along with code "4" (2PDT contacts). Bridge or potentiometer 10 kΩ, 0.25 W
min. (low voltage) for external time setting. Set timer dial to 0.0.
Rockwell Automation Publication 700-TD552A-EN-P
45
700-FS DIN Rail Mounted Timing Relay
Relays and Timer Specifications
Special Function Flasher (Repeat Cycle Starting with Pulse or Pause) Timing Relays
Description
t2 Setting
Up Switch
Down
1 Range Setting
Supply Voltages (A1/A2)
Z12 12V DC
Seperate Range
Settings
U23 24…48V DC, 24…240V AC, 50/60 Hz
t1 Setting
700-FSH3V
700-FSH3U
Function Diagram / Connection Diagram
(H) Flasher (Repeat Cycle Starting with Pulse or Pause)
The repeat cycle timer permits different settings for on and off times. The following operating modes are possible:
Oscillating mode; repeat cycle starts with voltage applied at A1 and B1, and continues to repeat until voltage is off.
One cycle mode; started by energizing B1 with voltage on A1 and A2.
Output starts with pulse or pause (switch ⊗ Up or Down).
700-FSH3U provides (1) range setting for t1 and t2.
700-FSH3V provides (2) range settings for t1 and t2.
Supply Voltage Controlled, Oscillating Mode Starting with Pause
— Switch ⊗ is Up
U
S
Output
LED
t2
t2
t1
t1
A1/A2
A1/B1
15 18
16
A1 B1
18 16
A2
Output
LED
A1/A2
t1
t2
A1
A1/B1
U
S
Output
15
Pulse Controlled, Output Starts With Pause (Min. Pulse AC 50
ms — DC 30 ms) — Switch ⊗ is Up One Cycle Mode — Voltage
Supplied at A1 and A2, then Pulsing “s” to Energize B1 will
Initiate One Cycle.
U
S
Supply Voltage Controlled, Oscillating Mode Starting with Pulse
— Switch ⊗ is Down
S
B1
t1
t2
t2 15 18
16
LED
15
U
S
Output
18 16
A1/A2
t1
A1/B1
t2
LED
LED Operation Chart Ñ Green LED
46
A2
15
18 16
Output at Shelf State, No Timing - LED OFF
Output at Shelf State, Time is Running - LED Flashing
Output NO Contact is Closed, No Timing - LED On
Output NO Contact is Closed, Time is Running - LED Long Flashing
Rockwell Automation Publication 700-TD552A-EN-P
s
A1 B1
15
t1 t2 15 18
16
Note: If B1 is pulsed, a one full time cycle consisting of t1 and t2 is completed.
LED
LED
LED
LED
A1 B1
Pulse Controlled, Output Starts with Pulse (Min. Pulse AC 50 ms
— DC 30 ms) — Switch ⊗ is Down One Cycle Mode — Voltage
Supplied at A1 and A2, then Pulsing “s” to Energize B1 will
Initiate One Cycle.
t1 t2 15 18
16
A2
t1
A1/A2
A1/B1
A2
18 16
Relays and Timer Specifications
700-FS DIN Rail Mounted Timing Relay
Function Diagram / Connection Diagram
(Q) Off-Delay without Supply Voltage (True Off-Delay) — When input power is turned on, the output contact changes state. When the
power is removed, the time delay begins. The output contact returns to shelf state at the end of the time delay.
U
Output
tp
A1/A2
t
15
15
A1
18
16
LED
A2
18 16
U
tp
Output 1
t
Output 2
LED
t
A1/A2
A1
15 18
16
25 28
26
A2
15
25
18 16 28 26
Note: Min. pulse (tp) required:
800 ms
(Y) Star-Delta Timing Relay — When power is applied, the output contact 17/18(Y) changes state. After the time setting, the output contact 17/18(Y) returns to
shelf state. After the fixed time (50… 60 ms), the output contact 17/28Δ changes state. Both output contacts return to shelf state whenever the power is
removed.
U
A1/A2
t
tu = 50...65 ms
LED
A1
17
A2
18
17/18
17/28
Rockwell Automation Publication 700-TD552A-EN-P
28
47
700-FS DIN Rail Mounted Timing Relay
Relays and Timer Specifications
Specifications
Time Characteristics (according to VDE 0435, Part 2021)
Setting Accuracy
±5% of full scale
Repeatability
±0.2% of the setting values
Tolerance
Voltage: ±0.001%/%ΔU
Temperature: ±0.025%/°C
General Data
Insulation Characteristics
2 kVAC/50 Hz test voltage according
to VDE 0435 and 6 kV 1.2/50 μs surge
voltage according to IEC 947-1
between all inputs and outputs
EMC/Interference Immunity
Performance of following requirements:
Surge capacity of the supply voltage
according to IEC 1000-4-5: 4 kV
1.2/50 μs
Burst according to IEC 1000-4-4: 6 kV
6/50 ns
ESD discharge according to IEC 10004-2: Contact 8 kV, air 8 kV
Electromagnetic HF field according to
IEC 801-3 and conducted
electromagnetic HF signal according to
IEC 801-6: Level 3
EMC/Emission
Electromagnetic fields according to EN
55 022: class B
Safe Isolation
According to VDE 106, part 101
Climatic Withstand
56 Cycles (24 hr) at 25…40 °C and
95% relative humidity according to IEC
68-2-30 and IEC 68-2-3
Supply
Supply Voltages
24…48V DC and 24…240V AC,
50/60 Hz (multi voltage)
Voltage Tolerance
–20…+20% (DC), –15…+10% (AC)
Power Consumption
0.5 W at 24V DC, 5 VA at 240V AC
Time Energized
100%
Reset Time
50 ms
Voltage Interruption
≤20 ms without reset (supply voltage)
Input Impedance
Relay ON: 3K-13K ohms
Relay OFF: 0.7K-4K ohms
Cable Length (Supply Voltage
Control)
Max. 250 m (800 ft)
Pulse Control (B1)
Pulse Duration
≥50 ms (AC), ≥30 ms (DC)
Vibration Resistance
4 g in three axes at 10…500 Hz, test
FC according to IEC 68-2-6
Input Voltage
Supply voltage range
Shock Resistance
50 g according to IEC 68-2-27
Input Current
1 mA
Max. Leakage Current
400 micro Amps
Protection Class
Enclosure:IP 40
IP 30 (Single-function)
Terminal:IP 20 according to IEC 947-1
Max. 250 m (800 ft) without parallel
load between B1 and A2
Max. 50 m (160 ft) with load (<3 kΩ)
between B1 and A2
Weight
100 g
Cable Length
Approval
UL, C-UL
Ambient Temperature
Open: –25…+60 °C
Enclosed: –25…+45 °C
Storage: –40…+85 °C
Terminals
Screw terminal M3.5 for Number 2
Posidrive, Philips, and slotted screws.
Suitable for power screwdriver. Rated
tightening torque 8.8 lb.-in. (0.8 N•m,
max. 1.2 N•m).
Dual-chamber system for terminal
cross-sections of 1 x 0.5 mm2…2 x 2.5
mm2 (solid) or stranded 2 x 2.5 mm2
(flexible with sleeve), #20…14 AWG.
Finger protection according to VDE
0106.
Mounting
Front mounting; For snap-on mounting
on 35 mm DIN Rail or screw fixing by
adapter and 2 screws (M4 type)
Disposal
Synthetic material without dioxin
according to EC/EFTA notification
Number 93/0141/D electrical contacts
with cadmium
Certifications
cULus Listed (File No. E14840, Guide
NKCR/NKCR7), CE Marked
Standards
EN/IEC 60947-1, EN/IEC 60947-5-1,
UL 508, CSA 22.2 No. 14
Outputs
Contact Type
Relay as changeover switch
Dielectric Coil to Contact
Withstand Voltage
5000 V
Voltage: 440V AC
Current Ith (AC-1): 8 A (5 A for 700FSQ)
Power: 2000 VA
According to IEC 947-5-1:
Switching Capacity
3 A/440V AC (inductive load, AC 14)
3 A/250V AC (inductive load, AC 15)
1 A/24V DC (inductive load, DC 13)
According to UL 508:
1.5 A/250V AC (B300)
3 A/120V AC (B300)
Short-Circuit Resistance
10 A gL
Mechanical: 30 million operations
Electrical operations:
4 Mil. at 1 A/250V AC, cos φ = 1
0.2 Mil. at 6 A/250V AC, cos φ = 1
1.5 Mil. at 1 A/250V AC, cos φ = 0.3
Life
0.3 Mil. at 3 A/250V AC, cos φ = 0.3
Temp. Code T4A
2A 32VDC MAX.
0.5 Mil. at 6 A/24V DC, resistive
2 Mil. at 4 A/24V DC, resistive
2 Mil. at 0.2 A/230V DC, resistive
1 Mil. at 0.4 A/24V DC, L/R = 20 ms
Mounting: Product shall be installed in an enclosure constructed in
accordance with the requirements of EN50021.
1 Mil. at 0.2 A/110V DC, L/R = 20 ms
1 Mil. at 0.1 A/230V DC, L/R = 20 ms
State Indicator
48
1 LED, combination signal
Rockwell Automation Publication 700-TD552A-EN-P
Accessories/ Specifications
Specifications
Ratings
Item
700-HNC
NEMA B300
Plug-in
85%…110% of rated supply voltage (12V DC: 90%…110% of rated supply voltage)‡
10% min. of rated supply voltage§
Relay ON:
1.5 VA (1.1 W) (at 24V AC, 60 Hz)
24V AC:
Relay OFF:
0.2 VA (0.1 W) (at 24V AC, 60 Hz)
Relay ON:
1.5 VA (1.3 W) (at 120V AC, 60 Hz)
100…120V AC:
Relay OFF:
0.8 VA (0.5 W) (at 120V AC, 60 Hz)
Relay ON:
1.8 VA (1.5 W) (at 230V AC, 60 Hz)
200…230V AC:
Relay OFF:
1.2 VA (0.9 W) (at 230V AC, 60 Hz)
Relay ON:
0.9 W (at 12V DC)
12V DC:
Relay OFF:
0.07 W (at 12V DC)
Relay ON:
0.9 W (at 24V DC)
24V DC:
Relay OFF:
0.07 W (at 24V DC)
Relay ON:
1.0 W (at 48V DC)
48V DC:
Relay OFF:
0.2 W (at 48V DC)
Relay ON:
1.3 W (at 110V DC)
100…110V DC:
Relay OFF:
0.3 W (at 110V DC)
Relay ON:
1.3 W (at 125V DC)
125V DC:
Relay OFF:
0.3 W (at 125V DC)
4PDT: 5 A at 250V AC, resistive load (cosφ = 1)
Pilot Duty Rating
Pin type
Operating voltage range
Reset voltage
Power consumption
Control outputs
Make
Break
Hp at 120V AC
Hp at 240V AC
Accuracy of operating time
Setting error
Reset time
Influence of voltage
Influence of temperature
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Ambient temperature
Ambient humidity
Life expectancy
120V
240V
120V
240V
AC
AC
AC
AC
Characteristics
30 A
15 A
3A
1.5 A
1/6 Hp
1/6 Hp
±1% FS max. (1 s range: ±1%±10 ms max.)
±10%±50 ms FS max.
Min. power-opening time: 0.1 s max. (including halfway reset)
±2% FS max.
±2% FS max.
100 mΩ min. (at 500V DC)
2000V AC, 50/60 Hz for 1 min (between current-carrying terminals and exposed non-current-carrying
metal parts)
2000V AC, 50/60 Hz for 1 min (between operating power circuit and control output)
2000V AC, 50/60 Hz for 1 min (between different pole contacts; 2-pole model)
1500V AC, 50/60 Hz for 1 min (between different pole contacts; 4-pole model)
1000V AC, 50/60 Hz for 1 min (between non-continuous contacts)
Malfunction:10…55 Hz, 0.5 mm single amplitude
Malfunction:100 m/s2 (approx. 10G)
Operating:-10 °C…50 °C (with no icing)
Storage:-25 °C…65 °C (with no icing)
Operating:35%…85%
Mechanical:10 000 000 operations min. (under no load at 1800 operations/hr)
Electrical:4PDT:
200 000 operations min. (3 A at 250V AC, resistive load at 1800 operations/hr)
Single-phase, full-wave-rectified power supplies can be used.
‡ When using the 700-HNC continuously in any place where the ambient temperature is in a range of 45 °C…50 °C, supply 90%…110% of the rated supply
voltages supply 95%…110% with 12V DC type).
Rockwell Automation Publication 700-TD552A-EN-P
49
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Characteristics, Continued
Noise immunity
±1.5 kV, square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)
Static immunity
Destruction:8 kV
Malfunction:4 kV
Enclosure rating
IP40
Weight
Approx. 50 g
Emission Enclosure:EN55011 Group 1 class A
Emission AC Mains:EN55011 Group 1 class A
Immunity ESD:EN61000-4-2:4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference:ENV50140:10 V/m (amplitude modulated, 80 MHz to 1 GHz) (level 3)
EMC
10 V/m (pulse modulated, 900 MHz)
Immunity Conducted Disturbance:ENV50141:10 V (0.15…80 MHz) (level 3)
Immunity Burst:EN61000-4-4:2 kV power-line (level 3)
2 kV I/O signal-line (level 4)
Standards
UL 508, CSA 22.2 No. 14, EN/IEC 61812-1
Certifications
cURus Recognized (File No. E14843, Guide NRNT2/NRNT8), CSA Certified (File 224268), CE Marked, CTick Marked
Timing Charts
Note :t:Set time
Rt:Reset time
Operating Mode
Timing Charts / Wiring Diagram
Power (13-14)
Time limit contact
NC (9-1, 10-2, 11-3, 12-4)
Time limit contact
NO (9-5, 10-6, 11-7,12-8)
Run/Power indicator (PW)
Output indicator (UP)
Power (13-14)
One Shot
Power
Output
Time limit contact
NC (9-1, 10-2, 11-3, 12-4)
Time limit contact
NO (9-5, 10-6, 11-7,12-8)
Run/Power indicator (PW)
Output indicator (UP)
Power (13-14)
Repeat Cycle OFF-Start
Time limit contact
NC (9-1, 10-2, 11-3, 12-4)
Power
Output
Time limit contact
NO (9-5, 10-6, 11-7,12-8)
Run/Power indicator (PW)
Output indicator (UP)
Power (13-14)
Repeat Cycle ON-Start
Power
Output
Time limit contact
NC (9-1, 10-2, 11-3, 12-4)
Time limit contact
NO (9-5, 10-6, 11-7,12-8)
Run/Power indicator (PW)
Output indicator (UP)
50
Rockwell Automation Publication 700-TD552A-EN-P
Timer
Circuit
UP
PW
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
General Timer Functions
Pulse Operation
A pulse output for a certain period can be obtained with a random external input
signal. Use the 700-HNC timing relay in interval mode as shown in the following
timing charts.
Output Indicator (Orange)
(Lit: Output ON)
Run/Power Indicator
(Green)
(Lit: Power ON)
1
2
3
4
5
6
7
8
Power (9-14)
Main Dial
Set the desired time
according to time range
selectable by DIP switch.
External short circuit
(5-13)
External input
(9-13)
9
10
11
Time limit contact NC
(10-2, 11-3, 12-4)
Run/Power indicator
(PW)
Output indicator (UP)
14
Timer
(—) Circuit
(~)
Time limit contact NO
(10-6, 11-7, 12-8)
12
13
(+)
(~)
UP FW
External Input
Note:
~
(
50 ms
min.
)
t: Set time
Rt: Reset time
DIP Switch Settings
Time Ranges
Cat. No.
Time Range
Time Setting Range
700-HNC44AZ12
700-HNC44AZ24
700-HNC44AZ48
700-HNC44AZ11
700-HNC44AZ25
700-HNC44AA24
700-HNC44AA12
700-HNC44AA23
1s
0.1 s…1 s
Yes
10 s
1 s…10 s
No
1 min
0.1 s…1 min
No
10 min
1…10 min
No
1 min
0.1…1 min
Yes
10 min
1…10 min
No
1 hr
0.1…1 hr
No
1 hr
1…10 hr
No
700-HNC44BZ12
700-HNC44BZ24
700-HNC44BZ48
700-HNC44BZ11
700-HNC44BZ25
700-HNC44BA24
700-HNC44BA12
700-HNC44BA23
Setting
Factory-Set
Note: The top two DIP switch pins are used to select the time ranges.
Operating Mode
Setting
Factory-set
ON-delay
Yes
One Shot
No
Repeat Cycle OFF-start
No
Repeat Cycle ON-start
No
Note: The bottom two DIP switch pins are used to select the time ranges.
Rockwell Automation Publication 700-TD552A-EN-P
51
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches) where not specified. Approximate Dimensions are not intended to be used for
manufacturing purposes.
Timers
Front Mounting
30.0
(1-3/16)
6.1 (15/64)
Fourteen 3 x 1.2 mm
Elliptic Holes
8
7
6
5
4
3
2
1
28
(1.10)
4.0
(0.15)
6.4
(0.25)
52.6
(2.07)
63.0
(2.48)
4.2
(5/32)
6.3
(.024)
21.5 max
(084)
24.9
(57/64)
21.1
(53/64)
14
13
12
11
10
62.0
(2-15/64)
65.0
(2-9/16)
9
26.0
(1-1/64)
Cat. No. 700-HN128
Wire Size: 2 x 1.5 mm2 (#2-16 AWG…#1-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) - Torque: 0.8 N•m (7 lb•in)
Cat.No. 700-HNC
27.0
(1.06)
Panel Mounting
60.9
(2.40)
21.5
(0.85)
28.9
(1-9/64)
24.5
(31/32)
35.6
(1.40)
76.0
(2.99)
67.0
(2-5/8)
3.2
(0.13)
18.9
(0.74)
34.9
(1.37)
32.0
(1.26)
35.5
(1.40)
2.5
(0.10)
#4-40
M3
30.0
(1-11/64)
Cat. No. 700-HN103
Cat. No. HN-104
Single wire: 0.2…2.5 mm2 (#24 AWG…14 AWG)
Double wire: 2 x 0.2 mm2…2 x 1.5 mm2 (2 x 24 AWG…2 x 16 AWG)
Wire type: solid or stranded, copper only
Strip length: 8 mm (5/16 in.), Torque: 0.5 N•m (4.4 lb•in)
Single Wire: 0.2…2.5 mm2 ( #24 AWG…14 AWG)
Double Wire: 2 x 0.2 mm2…2 x2.5 mm2 (2 x 24 AWG…2 x 14 AWG)
Wire Type: solid or stranded, copper only
Strip Length: 7 mm (9/32 in.), Torque: 0.5 N•m (4.4 lb•in)
Total height of 700-HN128 + 700-HNC is 82.5 mm.
52
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Specifications
Ratings
Item
Pilot Duty Rating
NEMA B300
Rated Supply Voltage
24V AC; 12, 24V DC
Pin Type
Plug-in
Operating Mode
ON-delay, One Shot, Repeat Cycle OFF start, or Repeat Cycle ON start selectable with DIP switch.
Operating Voltage Range
85%…110% of rated supply voltage (12 VDC: 90%…110% of rated supply voltage)
Power Consumption
24V AC:Relay ON:approx. 0.8 VA (at 24 VAC, 60 Hz)
Relay OFF:0.5 VA (at 24V AC, 60 Hz)
12V DC:Relay ON:approx. 0.4 W (at 12V DC)
Relay OFF:0.1 W (at 12V DC)
24V DC:Relay ON:approx. 0.5 W (at 24V DC)
Relay OFF:0.2 W (at 24V DC)
Control Outputs
5 A at 250V AC, resistive load (cosφ = 1)
The minimum applicable load is 10 mA at 5 VDC (P reference value).
Characteristics
120V AC
Make
Break
30 A
240V AC
15 A
120V AC
3A
240V AC
1.5 A
Hp at 240V AC
1/6 Hp
Accuracy of Operating Time
±1% FS max. (1 s range: +1%±10 ms max.)
Setting Error
±15%+50 ms FS max.
Reset Time
Min. power-opening time:
Influence of Voltage
±2% FS max.
12, 24V DC: 0.1 s max. (including halfway reset)
24V AC: 0.5 s max. (including halfway reset)
Influence of Temperature
±2% FS max.
Insulation Resistance
100 mΩ min. (at 500V DC)
Dielectric Strength
2000V AC, 50/60 Hz for 1 min (between operating circuit and control output, or contacts of different
poles)
1000V AC, 50/60 Hz for 1 min (between non-continuous contacts)
Vibration Resistance
Malfunction:10…55 Hz, 0.5 mm single amplitude
Shock Resistance
Malfunction:100 m/s2 (approx. 10G)
Ambient Temperature
Operating:-10 °C…50 °C (with no icing)
Storage:-25 °C…65 °C (with no icing)
Ambient Humidity
Operating:35…85%
Life Expectancy
Mechanical:10 000 000 operations min. (under no load at 1800 operations/hr)
Electrical:100 000 operations min. (3 A at 250V AC, resistive load at 1800 operations/hr)
Impulse Withstand Voltage
Between power terminals: 1 kV
Noise Immunity
±1.5 kV, square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)
Static Immunity
Destruction:8 kV
Malfunction:4 kV
Enclosure Rating
IP20
Weight
Approx. 18 g
EMC
Emission Enclosure:EN55011 Group 1 class A
Emission AC Mains:EN55011 Group 1 class A
Immunity ESD:EN61000-4-2:4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference:ENV50140:10 V/m (amplitude modulated, 80 MHz…1GHz) (level 3)
10 V/m (pulse modulated, 900 MHz)
Immunity Conducted Disturbance:ENV50141:10 V (0.15…80 MHz) (level 3)
Immunity Burst:EN61000-4-4:2 kV power-line (level 3)
2 kV I/O signal-line (level 4)
Standards
UL508, CSA C22.2 No. 14, EN/IEC 60947-5-1, EN/IEC 61812-1
Certifications
cURus Recognized Component (File No. E14843, Guide NRNTZ/NRNT8), CE Marked, C-Tick Marked
When using 700-HNK timer in any place where the ambient temperature is more than 50 °C, supply 90…110% of the rated voltages
(12V DC: 95…11 % of the rated voltage).
Note:
t: Set time
Rt: Reset time
Rockwell Automation Publication 700-TD552A-EN-P
53
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Bulletin 700-HNK — Ultra-Slim Timing Relay
General Timer Functions
Run/Power Indicator (Green)
(Lit: Power ON)
Main Dial
Set the desired time according to time
range selectable by DIP switch.
Output Indicator (Orange)
(Lit: Output ON)
Timing Chart
Operating Mode
700-HNK41…
700-HNK42…
Rt
t
t
Time limit contact
NC (4-2)
t
Output
t
Power (1-8)
ON-Delay
Power
Rt
t
Power (1-5)
Time limit contact
NO 4-3, 5-6
Time limit contact
NO (4-3)
Run/Power
indicator (PW)
Run/ Power
Output indicator
(OUT)
Indicator (PW)
Output Indicator
(OUT)
Power (1-5)
Rt
t
One shot
Time limit contact
NC (4-2)
Power
Time limit contact
NO (4-3)
Output
Run/ Power
t
Power (1-8)
Time limit contact
NO (4-3, 5-6)
Run/Power
indicator (PW)
Output indicator
(OUT)
Indicator (PW)
Output Indicator
(OUT)
t
t
t
t
Power (1-5)
Repeat Cycle OFF-Start
Power
t
t
t
t
Output indicator
(OUT)
Output Indicator
(OUT)
t
t
t
t
t
Power (1-5)
Power
Output
t
t
Time limit contact
NC (4-2)
t
Time limit contact
NO (4-3)
Run/ Power
Indicator (PW)
Output Indicator
(OUT)
54
t
Run/Power
indicator (PW)
Indicator (PW)
Repeat Cycle ON-Start
t
Time limit contact
NO (4-3, 5-6)
Time limit contact
NO (4-3)
Run/ Power
Output
t
Power (1-8)
Time limit contact
NC (4-2)
Power (1-8)
Time limit contact
NO (4-3, 5-6)
Run/Power
indicator (PW)
Output indicator
(OUT)
Rockwell Automation Publication 700-TD552A-EN-P
t
t
t
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Wiring Diagrams
3
4
5
4
2
6
3
Timer
Circuit
1
( )
( )
~
OUT
PW
Timer
1 Circuit
( )
( ~ ) OUT PW
8
( )
( )
~
5
( )
(~)
Cat. No. 700-HNK41...
Cat. No. 700-HNK42...
A pulse output for a certain period can be obtained with a random external input signal. Use the 700-HNK in interval mode as shown in the
following timing chart.
t
t
Rt
t
Power (3-8)
5
4
Rt
External Short Circuit (1-4)
External Input (1-3)
3
1
( )
( )
~
Time Limit Contact NO (6-5)
Run/Power Indicator (PW)
Output Indicator (OUT)
6
Timer
Circuit
OUT PW
50 ms
min.
8
( )
( )
~
Note: t: Set time
Rt: Reset time
External Input
~
(
)
Mode
Terminals
Pulse Operation
Power supply between 3 and 8
Short-circuit between 4 and 1
Input signal between 3 and 1
Operating mode; One shot and all other modes
Power supply between 1 and 8
Rockwell Automation Publication 700-TD552A-EN-P
55
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Time Ranges
Cat. No.
Time Range
Time Setting Range
1s
0.1…1 s
Yes
10 s
1…10 s
No
1 min
0.1 s…1 min
No
10 min
1…10 min
No
1 min
0.1…1 min
Yes
10 min
1…10 min
No
1 hr
0.1…1 hr
No
10 hr
1…10 hr
No
700-HNK41AZ12
700-HNK41AZ24
700-HNK41AA24
700-HNK42AZ12
700-HNK42AZ24
700-HNK42AA24
700-HNK41BZ12
700-HNK41BZ24
700-HNK41BA24
700-HNK42BZ12
700-HNK42BZ24
700-HNK42BA24
Setting
Factory-Set
Note: The left two DIP switch pins are used to select the time ranges.
Operating Modes
Operating Mode
Setting
On-delay
Yes
One Shot
No
Repeat Cycle Off-start
No
Repeat Cycle On-start
No
Note: The right two DIP switch pins are used to select the operating modes.
56
Factory-set
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
47.4
(1.86)
46.0
(1.81)
12.8
(0.50)
31.2
(1.22)
6
(0.23)
2.03
(5/64)
Five M3.5
x 0.315 Screws
21
6
4.06
(5/32)
12
2
3.0 Ø
(1/8)
Use M3 Screws
84.1
5 (+) (3-5/16)
(A1)
39.5
(1-17/32)
35.5
(1-13/32)
1 (-)
(A2)
4.06
(5/32)
15.6
(5/8)
6.0
(0.23)
Bulletin 700-HNK42 DPST-NO Contact
Approximate Dimensions
Bulletin 700-HNK41 SPDT Contact
Approximate Dimensions
11
4
14
3
46.0
(1.81)
31.2
(1.22) 28.8
(1.13)
28.8
(1.30)
7.11
(9/32)
47.0
(1.86)
12.8
(0.50)
29.9
(1-3/16)
54.1
(2-1/8)
7.11
(9/32)
22
7
24
5
2.03
(5/64)
Eight
M3.5 x 0.315
Screws
14
4
84.1
(3-5/16)
8 (+)
(A1)
4.06
(5/32)
11
3
12
2
4.06
(5/32)
39.5
(1-17/32)
3.0 Ø
(1/8)
Use M3 Screws
15.6
(5/8)
35.5
(1-13/32)
1 (-)
(A2)
29.9
(1-3/16)
54.1
(2-1/8)
Cat No. 700-HN121
Cat No. 700-HN122
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Total height: 700-HN121 + 700-HNK41 is 78.0 mm.
Holes required for mounting [3 mm (1/8 in.) diameter].
Wire Size: 2 x 2.5 mm2
Single Wire – Up to #12 AWG
Double Wire – 2 x 2.5 mm2 (#2–14 AWG… #2–20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) – Torque: 0.8 N•m (7 lb•in)
Total height: 700-HN122 + 700-HNK42 is 78.0 mm.
Holes required for mounting [3 mm (1/8 in.) diameter].
Rockwell Automation Publication 700-TD552A-EN-P
57
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
700-HR, HRS, -HRV
700-HRP
700-HRC
700-HRM
700-HRF
700-HRY
700-HRQ
700-HRT
(Transistor
Outputs)
Electrical Ratings
Pilot Duty Rating
NEMA B300
—
Thermal Current (Ith)
5A
100 mA @ 30V
DC max.
120V AC
30 A
—
240V AC
15 A
—
120V AC
3A
—
240V AC
1.5 A
Make
Break
Hp at 120V
—
1/6 Hp (0.12
kW)
1/4 Hp (0.18 kW)
1/6 Hp (0.12 kW)
Hp at 240V
1/3 Hp (0.25 kW)
Resistive Load
5 A at 250V AC/30V DC
Inductive Load
AC-15 @ 250V AC, 3 A/DC-13 @ 30V DC, 0.5 A
1/4 Hp (0.18
kW)
1/6 Hp (0.12
kW)
—
—
Accuracy of Operating Time
±0.2 % FS max. (±0.2 % ±10 ms max. in a range of 1.2 s)
Setting Error
±5 % FS ±50 ms (The value is ±5 % FS +100 ms to -0 ms max. when the C or D mode signal of the 700-HRVs are OFF.)
Influence of Voltage
±0.2 % FS max. (±0.2 % ±10 ms max. in a range of 1.2 s)
Influence of Temperature
±1 % FS max. (±1 % ±10 ms max. in a range of 1.2 s)
Permissible Leakage Current
Power Consumption
-HR52, -HRS
-HRV
-HRP, -HRC
-HRM
-HRF
-HRY
-HRQ
-HRT
240V AC, Output ON
2.1 VA
2.5 VA
2.0 VA
2.1 VA
10 VA
12 VA
0.4 VA
—
240V AC, Output OFF
1.3 VA
1.8 VA
2.0 VA
1.3 VA
10 VA
12 VA
0.4 VA
—
24V DC, Output ON
0.8 W
0.9 W
0.9 W
0.8 W
1.0 W
—
0.2 W
0.3 W
24V DC, Output OFF
0.2 W
0.3 W
0.9 W
0.2 W
1.0 W
—
0.2 W
0.2 W
Dielectric Strength
2000V
2000V
2000V
1000V
2000V
Vibration Resistance
Malfunction: 10…55 Hz with 0.5 mm double amplitude each in three directions for ten minutes each
Shock Resistance
Malfunction: 100 m/s2 (10 G)
Design Specifications
AC (1000V AC for 700-HRT), 50/60 Hz for 1 min (contact to frame)
AC (1000V AC for 700-HRT), 50/60 Hz for 1 min (between control output terminals and operating circuit)
AC, 50/60 Hz for 1 min (pole-to-pole)
AC, 50/60 Hz for 1 min (between contacts not located next to each other)
AC, 50/60 Hz for 1 min (contact to coil)
Mechanical
98 m/s2
(10 G)
294 m/s2
(10 G)
98 m/s2
(10 G)
100 m/s2
(10 G)
±1kV for
48V DC
±1.5 kV for
±600V DC
Environmental
Noise Immunity
±1.5 kV for ±600V DC
±400V for 12V DC
Static Immunity
Malfunction: 8 kV
Ambient Temperature
Operating: -10…55 °C (with no icing)
Storage: -25…65 °C (with no icing)
Ambient Humidity
Operating: 35…85 %
Life Rxpectancy
(Min. Operations)
Mechanical:20 000 000. (under no load at 1800 operations/h)
Electrical: 100 000 (5 A at 250V AC, resistive load at 1800 operations/h)
EMC
(EMI) EN50081-2
Emission Enclosure:EN55011 Group 1 class A
Emission AC Mains: EN55011 Group 1 class A
(EMS) EN50082-2
Immunity ESD:EN61000-4-2:4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference from AM Radio Waves: ENV50140:10 V/m (80 MHz…1 GHz) (level 3)
Immunity RF-interference from Pulse-modulated Radio Waves:ENV50204:10 V/m (900 ±5 MHz) (level 3)
Immunity Conducted Disturbance:ENV50141:10 V (0.15…80 MHz) (level 3)
Immunity Burst:EN61000-4-4:2 kV power-line (level 3)
Immunity Surge:EN61000-4-52 kV I/O signal-line (level 4)
1 kV line to line
2 kV line to ground (level 3)
Degree of Protection
IP40 (panel surface)
Construction
Mech: 107
Electrical: 104
Weight
Approx. 90 g
Certifications
CSA Certified (File No. 70751), UL Recognized (File No. E14843 Guide No. NRNT2), CE Marked, C-Tick Marked
Standards
UL 508, CSA C22.2 No. 14, EN 61812-1, EN 61000-6-2, -6-4
58
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Timer Functions
700-HR Multifunction Timer
Power indicator (green) (Flashes when Timer operates;
lit when Timer stops operating)
Operating mode display window
Operating mode selector
Select a mode from:
A, B, B2, C, D, E, J, and G (700-HR52, -HRV, and HRT 6)
A, E, B2, J, and B (800-HRS, -HRP, and -HRT4)
Output indicator (orange)
(Lit when energized)
Scale range display windows
Time unit display window
Time Range selector (select
one from 1.2, 3, 12, and 30 at
full scale.)
Time setting
knob (set time)
Time unit selector (select one from sec, 10 s, min, 10 m, hrs, and 10 h)
700-HRC -HRM On-Delay Timer
Power indicator (green) (Flashes when Timer operates;
lit when Timer stops operating)
Output indicator (orange)
(Lit when energized)
Scale range display windows
Time unit display window
Time Range selector (select
one from 1.2, 3, 12, and 30 at
full scale.)
Time setting
knob (set time)
Time unit selector (select one from sec, 10 s, min, 10 m, hrs, and 10 h)
700-HRF Twin Timer
OFF indicator (green)
Lit when the output is OFF.
OFF-time unit display
ON indicator (orange)
Lit when the output is ON.
OFF-time unit selector (select
one from sec, 10 s, min., 10 m, hrs, and 10 h)
ON-time setting knob (with orange pointer)
For ON-time setting
Scale range display windows
OFF-time setting knob (with green pointer)
For OFF-time setting
Time range selector (select
one from 1.2, 3, 12, and
30 at full scale.)
ON-time unit display
ON-time unit selector (select
one from sec, 10 s, min., 10 m, hrs, and 10 h)
700-HRY Star-Delta Timer
Star operation indicator
(green)
Delta operation indicator
(orange)
Time unit display
(sec. is fixed)
Scale range display windows
Time setting knob (for setting
star operation time)
Star operation time range selector
(select one from 6, 12, 60 and
120 at full scale.)
Star-delta transfer time selector (select
one from 0.05 s, 0.1 s, 0.25 s, 0.5 s, 0.75 s and 1.0 s)
Star-delta transfer time unit display
700-HRQ True Off-Delay Timer
Scale range display windows
Output indicator (red)
Time setting knob (for setting OFF-delay time)
Time range selector (select one from 0.6, 1.2, 6, and 12
at full scale.)
True OFF-Delay time unit display
Rockwell Automation Publication 700-TD552A-EN-P
59
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Specifications for Start, Gate, Reset Signal (Cat. Nos. 700-HR52, -HRT6, -HRV, -HRQR)
Start, Reset, and Gate signals are typically contact closures or signals from a solid-state sensor.
(R) Reset Signal
The reset signal is not required for normal operation. Reset
can be accomplished by removing power from the timing
relay. To reset the timer without removing power, a signal
must be applied which resets the timing cycle and returns
the output contacts to their shelf state. The reset signal will
override both the start signal and gate signal. The reset
signal can be either momentary or maintained.
Power to Timing Relay
t1< T
t1
T
t1
t2
Reset Signal
Timing Cycle
Timing Relay Output
(G) Gate Signal
The gate signal is not required for normal operation. The
gate signal provides a pause or retentive timing function.
When the gate signal is applied the timing cycle is
momentarily interrupted. When the signal is removed, the
timing cycle resumes timing at the point the cycle was
interrupted and will continue timing until the time delay is
completed or the gate signal is re-applied.
Power to Timing Relay
t1+t2 = T
Gate (pause)
Timing Cycle
Timing Relay Output
Contact Signal — Cat. Nos. 700-HR52, -HRT6, -HRQR
Contact closure provides signal to timer. A low energy signal
is generated by the 700-HR timing relay. For optimum
reliability, use contacts designed for low energy switching
(5V, 1 mA) (Bul. 800F-X__V, 800T-X__V). No external voltage
should be connected to the contact signal.
R
S
G
5v, 1mA
Contact Signal — Cat. No. 700-HRV
For use in applications where it is not possible to use
contacts designed for low energy switching. Contact closure
provides signal to timer. A signal is generated by the 700-HR
timing relay, and is the same potential as the supply voltage
of the timing relay. No external voltage should be connected
to contact signal. 700-HRV52TU24 supply voltage: 24...48V
AC, 12...48V DC / 700-HRV52TA17 supply voltage:
100...240V AC, 100...125V DC.
S
U
U
(+)
( )
Solid-State Signal — Cat. Nos. 700-HR52, -HRT6
Timing relay is suitable for use with a 3-wire NPN 12...24V
DC sensor. Supply voltage potential of sensor must be
the same as the supply voltage potential of the timing
relay. Permissible off-state leakage current from sensor:
0.01 mA max.
+ 12...24V DC
COM
0.1mA
R
S
G
COM ( )
(+) 12...24V DC
Solid-State Signal — Cat. No. 700-HRV
Timing relay is suitable for use with a 3-wire NPN or PNP
12...24V DC sensor. Supply voltage potential of sensor must
be the same as the supply voltage potential of the timing
relay. Permissible off-state leakage current from sensor: 0.01
mA max.
S
S
PNP Wiring Diagram
60
+ 12...24 V DC
COM
+ 12...24V DC
COM
COM ( )
(+) 12...24V DC
Rockwell Automation Publication 700-TD552A-EN-P
NPN Wiring Diagram
COM ( )
(+) 12...24V DC
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Signal Specifications
Circuit Impedance
Circuit impedance can be used to calculate the maximum wiring distance from the signal switch to the timing relay, for example.
Permissible signal-ON impedance: 1 kΩ max.
Permissible signal-OFF impedance: 100 kΩ min.
Power-OFF Reset
Min. power-off time: 0.1 s, Reset Voltage: 10% max. of rated voltage
Signal Duration
Min. pulse width: 0.05 s
Signal Options
700-HR52
700-HRT6
700-HRV5
700-HRQR
Start
X
X
X
NA
Reset
X
X
NA
X
Gate
X
X
NA
NA
Nomenclature
Timing Charts
Mode A — ON-Delay
a. Needs continuous input power applied.
b. Timing is initiated by the leading edge of the start signal.
c. Contacts change state after timing is complete.
d. Additional start signals during timing don't reset timing or contacts.
e. When the input power is removed contacts return to shelf state.
Basic Operation
T
Power
T
Power
Start
Start
Output (N.C.)
Output
Output (N.O.)
Power LED
Mode B — Repeat Cycle, Off Start
a. Need continuous input power applied.
b. Timing is initiated by the leading edge of the start signal. Additional start signals during timing do not reset timing or contacts.
c. For the first time period the contacts remain in their shelf state. When that time period is complete contacts change state for the same time
period (time on = time off).
d. This cycle repeats itself until input power is removed or reset signal is applied. When the input power is removed or reset signal is applied
contacts return to the shelf state.
Basic Operation
T
T
T
Power
Start
Output (N.C.)
Output (N.O.)
Power LED
T
T
T
Power
Start
Output
a. Need continuous input power applied.
b. Timing is initiated by the leading edge of the start signal. Additional start signals during timing do not reset timing or contacts.
c. For the first time period the contacts change state. When that time period is complete contacts return to the shelf state for the same time
period (time on = time off).
d. This cycle repeats itself until input power is removed or reset signal is applied. When the input power is removed or reset signal is applied
contacts return to the shelf state.
Basic Operation
Power
Start
Output (N.C.)
T
T
T
Power
Start
T
T
T
Output
Output (N.O.)
Power LED
Rockwell Automation Publication 700-TD552A-EN-P
61
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Mode C — Watchdog monitor (Trigger = Signal On/Off)
a. Need continuous input power applied.
b. Contacts change state immediately when start signal is applied or when start signal is removed (only if timing cycle was complete).
c. Timing is initiated at the leading edge of the start signal. After the first timing cycle is complete, timing is initiated by the trailing edge of the
start signal.
d. At the end of the time period contacts return to the shelf state.
e. Relay timing is reset when additional start signals are applied while the relay is timing. Contacts remain in energized state.
f. When the input power is removed contacts return to the shelf state.
Power
T
T
t
t<T
T
Basic Operation
Start
Output (N.C.)
T
Power
Start
Output (N.O.)
Power LED
Mode D — Off-Delay (Trigger=Signal Off)
T
Output
a. Need continuous input power applied.
b. Contacts change state immediately when start signal is applied.
c. Timing is initiated by the trailing edge of the start signal.
d. At the end of the time period contacts return to the shelf state.
e. Relay timing is reset when additional start signals are applied while the relay is timing. Contacts remain in energized state.
f. When the input power is removed contacts return to the shelf state.
Basic Operation
t
T
Power
t<T
Start
Power
Start
Output (N.C.)
Output
T
Output (N.O.)
Power LED
Mode E — One-Shot (Trigger=Signal On) 700-HR52, -HRV, and -HRT6
a. Need continuous input power applied.
b. Timing is initiated by the leading edge of the start signal.
c. Contacts change state immediately when start signal is applied.
d. At the end of the time period contacts return to the shelf state.
e. Relay timing is reset when additional start signals are applied while the relay is timing. Contacts remain in energized state.
f. When the input power is removed contacts return to shelf state.
Basic Operation
Power
T
t
T
t<T
Power
Start
Start
Output (N.C.)
Output (N.O.)
Power LED
T
Output
Mode E — One-Shot (Trigger = Power On) 700-HRS, -HRP, and -HRT4
a. Need continuous input power applied.
b. Timing is initiated when the input power is applied.
c. At the end of the time period contacts return to the shelf state.
d. Relay timing is reset when input power is removed.
Basic Operation
Power
Timed Output (N.C.)
Timed Output (N.O.)
Power LED
62
T
t<T
Power
Output
Rockwell Automation Publication 700-TD552A-EN-P
T
Relays and Timer Specifications
700-HNC Plug-in Timing Relay
Mode J — Delayed One-Shot (Trigger=Power On)
a. Need continuous input power applied.
b. No start signal applied.
c. Timing is initiated when input power is applied.
c. Contacts change state after the timing for a fixed time of 1s +/-0.5s
d. At the end of the 1 sec period the contacts return to the shelf state.
e. When the input power is removed contacts return to the shelf state.
Basic Operation
T
Power
T
1s ±0.5s
Output (N.C.)
Power
1s ±0.5s
Output (N.O.)
Output (N.O.)
Power LED
Power LED
Mode Star-Delta
a. Need continuous input power applied.
b. No start signal required. Timing is initiated when input power is applied.
c. Star ouput contact changes state when input power is applied.
d. After timing is complete star output contact returns to the shelf state then both the star & delta contacts remain in shelf states until transfer
time setting is complete.
e. Delta output contact changes state after transfer time is complete.
f. Instantaneous contact changes state when input power is applied.
g. All contacts return to the shelf state when input power is removed.
Power
Basic Operation
t2
t1
Output (N.C.)
Power
Output (N.O.)
Instantaneous Output
Output 8-5,
LED
Output 8-5,
LED
Output 8-6,
LED
Output 8-6,
LED
t1
t2
Mode True Off-Delay (Trigger=Power Off)
a. Continuous input power is NOT required.
b. No start signal applied.
c. Contacts change state immediately when input power is applied.
d. Timing starts when input power is removed.
e. At the end of the time period contacts return to the shelf state.
f. Relay timing is reset when input power is reapplied while the relay is timing. Contacts remain in energized state.
t<T
T
t
T
Basic Operation
Power
T
Output (N.C.)
Power
Output (N.O.)
Output
Relay On LED
Relay On LED
Rockwell Automation Publication 700-TD552A-EN-P
63
700-HNC Plug-in Timing Relay
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
81.5
(3-7/32)
52.3
(2-1/16)
15.0
(19/32)
3
Mode
2
4
hrs
6
Range
78
(3.07)
63.7
(2.51)
0.7
(0.03)
48.0
(1-57/64)
5
0
6
(.24)
Up
1
48.0
(1-57/64)
15
(.59)
Power
A
39
(1.54)
Unit
44.8
(1.76)
48.0
(1-57/64)
6.0
(1/4)
Cat. No. 700-HR, -HRM, -HRC, -HRF,
-HRS, -HRV, -HRP, -HRY, -HRQ Timing Relays
Cat. No. 700-HR, -HRM, -HRC,
-HRF, -HRS, HRV, HRP
Cat. No. 700-HRY, -HRQ Timing Relays
Timing Relays
Panel
35.0
(1-3/8)
45.0
(1-25/32)
57.0
(2-11/32)
32.0
(1-1/4)
45.0
(1-49/64)
24.0
(31/32)
45.0
(1-25/32)
Cat. No. 700-HN129 — 11-pin
Cat. No. 700-HN108 — 8-pin socket
Cat. No. 700-HR…
Panel Cutout
30
(1-3/16)
22
12
5
4
24
Retainer
24.6
(31/32)
20.8
(53/64)
40.1
(1-37/64)
26
(1-1/32)
14
6
Cat. No. 700-HN130
2
1
8
Ø 24.9
(63/64)
7
3
65
(2-35/64)
7
Ø 4.2
(5/32)
2
8
1
A2
A1
21
54.9
(2-5/32)
11
3
38
(1-1/2)
#4_40
M3
4
5
51.1
(2-1/64)
6
33.0
(1-19/64)
14.7
(37/64)
Cat. No. 700-HN100
Cat. No. 700-HN125
Wire Size: 2x2.5 mm
Single Wire — Up to #12 AWG
Double Wire — 2x2.5 mm (#2-14 AWG…#2-20 AWG)
(Either Solid or Stranded)
Strip length: 9 mm (3/8 in) — Torque: 0.8 N•m (7 lb•in)
Wire Size: 2x2.5 mm
Single Wire— Up to #12 AWG
Double Wire — 2x2.5 mm (#2-14…#2-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) — Torque: 0.8 N•m (7 lb•in)
Panel Mounting
30
(1-3/16)
24
21 22
1
12
32
6
7
9
3
65
(2-35/64)
10
11
1
54.9
(2-5/32)
9
4
8
5
7
6
Ø 4.2
(5/32)
51.1
(2-1/64)
2
14
#4_40
M3
A2 31 11 A1
38
(1-1/2)
64
26.9
(1.06)
10
3
4
24.6
(31/32)
20.8
(53/64)
11
2
5
8
34
59.2
(2-1/3)
7.9
(0.31)
26
(1-1/32)
52.3
(2.06)
Cat. No. 700-HN100
Cat. No. 700-HN126
Wire Size: 2x2.5 mm
Single Wire — Up to #12 AWG
Double Wire — 2x2.5 mm (#2-14 AWG…#2-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in.) — Torque: 0.8 N•m (7 lb•in.)
Wire Size: 2x2.5 mm
Single Wire— Up to #12 AWG
Double Wire — 2x2.5 mm (#2-14…#2-20 AWG)
(Either Solid or Stranded)
Strip Length: 9 mm (3/8 in) — Torque: 0.8 N•m (7 lb•in)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HX Plug-in Timing Relay
General Timer Functions
Operation Key
Display Section
1. Key Protect Indicator (orange)
2. Control Output Indicator (orange)
3. Reset Indicator (orange)
4. Present Value Display (Main display)
*)
(Character height: 12 mm, red
* Characters on models with screw terminals
can be switched between red, green, and orange.
1
2
3
8
4
8. Mode Key
5
9. Reset Key
6
(Changes modes and setting items)
(Resets present value and output)
7
10. Up Keys 1 to 4
10
11. Down Keys 1 to 4
11
9
Switches
5. Time Unit Indicators
(Color is same as present value display.)
(If the time range is 0 min, 0 h, 0.0 h, or 0 h
0 min, these indicators flash to indicate
timing operation.)
Front View
12. Key-protect Switch
(Default setting)
12
OFF
(Disabled)
ON
(Enabled)
6. Set Value Display (Sub-display)
(Character height: 6 mm, green)
7. Set Value 1, 2 Indicator (green)
Character Size
for Present
Value Display
12mm
Character Size
for Set Value
Display
6mm
Rockwell Automation Publication 700-TD552A-EN-P
65
700-HX Plug-in Timing Relay
Relays and Timer Specifications
Specifications
Electrical Ratings
Pilot Duty Rating
NEMA B300
Rated supply voltage
100 to 240V AC, 24V AC/12 to 24V DC (50/60Hz) (permissible ripple: 20%(p-p)
max.)
Operating voltage range
Power consumption
Inrush Current
Make
Break
85…110% of rated supply voltage
100…240V AC
4.3VA
24V AC/12…24V DC
3.4VA/1.7 W
100…240V AC
3A
24V AC/12…24V DC
5A
120V AC
30 A
240V AC
15 A
120V AC
3A
240V AC
Hp at 120V AC
1.5 A
1/4 Hp
Hp at 240V AC
1/3 Hp
Mechanical
Mounting Method
Flush mounting, surface mounting, DIN mounting
Display
Seven-segment, negative transmissive LCD; Present value (red, 12 mm high
characters); Set value (green, 6 mm high characters)
Digits
Four digits
Time ranges
Timer
Inputs
0.000…9.999 s, 0.00…99.99 s, 0.0…999.9 s, 0…9999 s, 0 min 00 s…99 min 59
s, 0.0…999.9 min, 0 hr 00 min…99 hr 59 min, 0.0 hr…999.9 hr, 0 hr…9999 hr
Timer modes
Elapsed time (Up), remaining time (Down), selectable
Output modes
A, A-1, A-2, A-3, B, B-1, D, E, F, Z, S, tOFF, tON, tOFF-1, or tON-1
Input signals
Start, reset
Input method
No-voltage input via:NPN transistor or switching of contact
Start, reset, gate
Minimum input signal width: 1 or 20 ms (selectable)
Power reset
Minimum power-opening time: 0.5 s (Except for A-3, B-1, and F mode)
SPDT contact output: 5 A at 250V AC, resistive load (cosine=1)
Minimum applied load: 10 mA at 5 V DC (failure level: P, reference value)
Control output
External Power Supply
No
Key Protect
Yes
Memory Backup
EEP-ROM (overwritten 100 000 times min), which can store data for 10 years
min.
Accuracy of Operating Time and Setting Error
Power-ON start: +-0.01% +-50 ms max.
* to be rated against set value
Signal start: +- 0.005% +-30 ms max.
* to be rated against set value
Signal start at transistor output model: +- 0.005% +-3 ms max.‡
If the set value is within the sensor waiting time
(250 ms max.)
The values are based on the set value.
‡ The value is applied for a minimum pulse width of 1 ms.
66
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HX Plug-in Timing Relay
Characteristics
Insulation Resistance
100 mΩ min. (at 500V DC)
Dielectric Strength
2000V AC, 50/60Hz for 1 min between current-carrying terminals and non-currentcarrying metal parts (1000V AC for 24V AC/12 to 24V DC type), 1000 VAC, 50/60 Hz for
1 min between non-continuous contacts
Noise Immunity
'+-1.5 kV (between power terminals) for 100 to 240 VAC, +-480V for 24VAC/12 to
24VDC, and +-600V (between input terminals), square-wave noise by noise simulator
(pulse width: 100 ns/1 μs, 1-ns rise)
Static Immunity
±8 kV (malfunction), ±15 kV (destruction)
Vibration Resistance
Malfunction
10…55 Hz with 0.35 mm single amplitude each in three directions for 10 min
Shock Resistance
Malfunction
98 m/s2 (approx. 10 G) each in three directions
Mechanical
10 million operations min. (under no load at 18 000 operation/hr)
Electrical
100 000 operations min. (5 A at 250V AC, resistive load at 1800 operation/hr)
Life Expectancy
EMC
(EMI)
EN61812-1
Emission Enclosure:
EN55011 Group1 class A
Emission AC mains:
EN55011 Group1 class A
(EMS)
EN61812-1
Immunity ESD:
EN61000-4-2: 4 kV contact discharge (level2) 8 kV air discharge (level3)
Immunity RF-interference:
EN61000-4-3: 10 V/m
Enclosure Ratings
Panel surface:IP66 and NEMA Type 4X (indoors)‡
Weight
Approx. 100 g
Certifications
CE Certified; cURus (File No. E14843, Guide NRNTZ/NRNT8), C-Tick Marked
Standards
EN61010-1, EN 61326, VDE0106/P 100, CSA C22.2 No. 14, UL 508
700-HX User Manual, pub. number 700-UM002_-EN-D, available at Literature Library.
‡ An attached waterproof packing is necessary to ensure IP66 waterproofing between the 700-HX and installation pan.
Rockwell Automation Publication 700-TD552A-EN-P
67
700-HX Plug-in Timing Relay
Relays and Timer Specifications
Timing Charts
One-Shot
Sustained Output
One-shot outputs can be set to
0.1s, 0.5 s, 1 s, 5 s, 10 s, or 20 s.
Output Mode A Mode: Signal ON-Delay (Timer resets when power comes ON.)
Timing starts when the start signal goes ON.
While the start signal is ON, the timer starts when
power comes ON or when the reset input goes OFF.
The control output is controlled using a sustained
or one-shot time period.
Power
Start signal
Basic Operation
Gate*
Reset
t
t
t
Control output
Power
**
Start Signal
Input
Timing
Set value
Timing
diagram
UP
Output
0
Set value
DOWN
0
*Output is instantaneous when setting is 0.
** Start signal input is enabled during timing.
Output Mode A-1: Signal ON-Delay 2 (Timer resets when power comes ON.)
Timing starts when the reset input goes ON and is
reset when the start signal goes OFF.
While the start signal is ON, the timer starts when
the power comes ON or when the reset input goes OFF.
The control output is controlled using a sustained
or one-shot time period.
Power
Start signal
Gate*
Basic Operation
Reset
Power
Control output
Start Signal
Input
Set value
UP
Timing
diagram
0
Timing
Output
Set value
DOWN
0
*Output is instantaneous when setting is 0.
Output Mode A-2: Power ON Delay 1 (Timer resets when power comes ON)
Power
Timing starts when the reset input goes OFF.
The start signal disables the timing function (i.e.,
same function as the gate input).
The control output is controlled using a sustained
or one-shot time period.
Start signal
Gate *
Basic Operation
Reset
Power
Control output
Timing
Set value
Timing
diagram
UP
Output
0
*Output is instantaneous when setting is 0.
Set value
DOWN
0
Output Mode A-3 Power ON Delay 2 (Timer does not reset when power comes ON)
Power
Timing starts when the reset input goes OFF.
The start signal disables the timing function (i.e.,
same function as the gate input).
The control output is controlled using a sustained
or one-shot time period.
Start signal
Gate *
Reset
Basic Operation
Power
Control output
Timing
Set value
Timing
diagram
UP
Sustained
Output
*Output is instantaneous when setting is 0.
0
Set value
DOWN
0
Gate not included on any mode of this relay.
68
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HX Plug-in Timing Relay
Output Mode B: Repeat Cycle (Timer resets when power comes ON.)
Timing starts when the start signal goes ON.
The status of the control output is reversed when time
is up (OFF at start).
While the start signal is ON, the timer starts when the
power comes ON or when the reset input goes OFF.
Sustained Output
Basic Operation
Power
Start signal
Power
Gate*
**
Start Signal
Input
Reset
Timing
Control output
UP
Timing
Timing
Output
Set value
Timing
diagram
Timing
0
* Normal output operation will not be possible if the
set time is too short.
Set the value to at least 100 ms (contact output type).
** Start signal input is disabled diring timing.
Set value
DOWN
0
Timing starts when the start signal goes ON.
The control output is turned ON when time is up.
While the start signal is ON, the timer starts when the
power cones ON or when the reset input goes OFF.
One-Shot Output
Power
Basic Operation
Start Signal
Power
**
Start Signal
Input
Gate*
Reset
Timing
Control Output
Timing
Timing
Timing
Output
* Normal output operation will not be possible if the
set time is too short.
Set the value to at least 100 ms (contact output type).
** Start signal input is disabled during timing.
Set Value
0
Timing UP
Set Value
Diagram
0
DOWN
Output Mode B-1: Repeat Cycle 2 (Timer does not reset when power comes ON)
Timing starts when the start signal goes ON.
The status of the control output is reversed when
time is up (OFF at the start).
While the start signal is ON, the timer starts when the
power comes ON or when the rest input goes OFF.
Sustained Output
Basic Operation
Power
Power
**
Start Signal
Input
Start signal
Gate*
Timing
Reset
Set value
Timing
diagram
Timing
Output
Control output
UP
Sustained
* Normal output operation will not be possible
if the set time is too short
Set the value to at least 100 ms (contact
output type).
** Start signal input is disabled during.
0
Set value
DOWN
0
One-Shot Output
Timing starts when the start signal goes ON.
The control output comes ON when time is up.
While the start signal is ON, the timer starts when
the power comes ON or when the reset input goes OFF.
Basic Operation
Power
Power
Start signal
Gate*
**
Start Signal
Input
Timing
Timing
Reset
Output
Control output
Set value
Timing
diagram
UP
0
Set value
DOWN
0
Sustaining
* Normal outout operation will not be possible if the
set time is too short.
Set the value to at least 100 ms (contact output type).
** Start signal input is disabled during timing.
Gate not included on any mode of this relay.
Rockwell Automation Publication 700-TD552A-EN-P
69
700-HX Plug-in Timing Relay
Relays and Timer Specifications
Output Mode D: Signal OFF-Delay (Timer resets when power comes ON.)
The control output is ON when the start signal is
ON (except when the power is OFF or the reset
is ON).
The timer is reset when the time is up.
Power
Start signal
Basic Operation
Gate*
Power
Reset
**
Start Signal
Input
Control output
Timing
Set value
Timing
diagram
UP
Output
0
* Output functions only during start signal input
when setting is 0.
** Start signal input is enabled during timing.
Set value
DOWN
0
Output Mode E: Interval (Timer resets when power comes ON.)
Timing starts when the start signal comes ON.
The control output is reset when time is up.
While the start signal is ON, the timer starts when
power comes ON or when the reset input goes OFF.
Basic Operation
Power
Start signal
Power
**
Start Signal
Input
Gate*
Reset
Timing
Control output
Set value
Timing
diagram
UP
Output
0
Set value
DOWN
0
* Output is disabled when the setting is 0.
** Start signal input is enabled during timing.
Output Mode F: Cumulative (Timer does not reset when power comes ON)
Start signal enables timing (timing is stopped when the
start signal is OFF or when the power is OFF).
A sustained control output is used.
Basic Operation
Power
Start Signal
Input
Timing
Output
Timing
Sustained
*Output is instantaneous when setting is 0.
Gate not included on any mode of this relay.
70
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HX Plug-in Timing Relay
Z Mode
Output quantity can be adjusted by changing the cycle time set in the adjustment level to 1 and by changing the ON duty (%) set value. The
set value shows the ON duty (%) and can be set to a value between 0 and 100 (%). When the cycle time is 0, the output will always be OFF.
When the cycle time is not 0 and when ON duty has been set to 0 (%), the output will always be OFF. When ON duty has been set to 100
(%), the output will always be ON.
Z mode: ON/OFF-duty Adjustable Repeat Cycle
Timing starts when the start signal goes ON.
The status of the control output is reversed
when time is up (ON at start).
While the start signal is ON, the timer starts when
power comes ON or when the reset input goes OFF.
Power
Start signal
Basic Operation
Power
* Gate
**
Start signal
input
Reset
Timing
ON duty (%)
ON duty setting
(%) ON time
0
UP
Timing
(cycle time)
Timing
(cycle time)
Control Output
Cycle time
Timing
ON duty (%)
Output
Cycle time
Timing
diagram
* Normal output operation will not be possible if the
set time is too short.
Set the value to at least 100 ms (contact output
type).
** Start signal input is enabled during timing.
ON duty setting
(%) ON time
DOWN
0
Output Mode S: Stop Watch (Timer resets when power comes ON)
Power
Start signal
Gate/Reset
Timing diagram
9999
The signal starts and stops timing.
The display is held and timing is continued if the reset
or gate input is received during timing operation.
The timer resets if the reset or gate input is received
when the timing operation is stopped.
Basic Operation
Set time
Power
UP
0
Start signal
input
Set time
Gate/Reset
Timing
DOWN
0
Output
*
Display
(for elapsed
time)
* RST flashes
Note: Output is instantaneous when setting is 0.
Output Mode T OFF: Twin Timer OFF start
Sustained Output
Power
Start signal
Timing starts when the start signal goes ON.
The status of the control output is reversed when time
is up (OFF at start).
While the start signal is ON, the timer starts when
power comes ON or when the reset input goes OFF.
Basic Operation
* Gate
Reset
Control Output
Power
**
Start Signal
Input
Timing
OFF
OFF Time
UP
Timing
diagram
ON Time
Timing
OFF
Timing
ON
Output
0
OFF Time
DOWN
Timing
ON
ON Time
0
* Normal output operation will not be possible if the
ON/OFF set time is too short. Set the value to at least
100 ms (contact output type).
** Start signal input is disabled during timing.
Gate not included on any mode of this Relay.
Rockwell Automation Publication 700-TD552A-EN-P
71
700-HX Plug-in Timing Relay
Relays and Timer Specifications
Output Mode T ON: Twin Timer ON start
Sustained Output
Timing starts when the start signal goes ON.
The status of the control output is reversed when time
is up (ON at start).
While the start signal is ON, the timer starts when
power comes ON or when the reset input goes OFF.
Power
Start signal
Basic Operation
* Gate
Power
**
Start Signal
Input
Reset
Control Output
Timing
ON
OFF Time
UP
ON Time
Timing
diagram
Timing
OFF
Timing
ON
Timing
OFF
Output
0
OFF Time
DOWN
* Normal output operation will not be possible if the
ON/OFF set time is too short. Set the value to at least
100 ms (contact output type).
** Start signal input is disabled during timing.
ON Time
0
Output Mode TOFF-1: Flicker OFF start 2 (Timer does not reset when power comes ON)
Timing starts when the start signal goes ON.
The status of the control output is reversed when time is
up (OFF at start).
While the start signal is ON, the timer starts when the
power comes ON or when the reset input goes OFF.
Power
Start signal
Basic Operation
Gate
Power
Reset
*
Start signal
input
Timing diagram
Control output
OFF time
UP
ON time
Timing
OFF
Timing
ON
Timing
OFF
a
b
Output
(a + b = ON time)
* Start signal input is disabled during timing.
0
Note: Normal output operation will not be possible if
the set time is too short.
Set the value to at least 100 ms (contact output
type).
OFF time
DOWN
ON time
0
Output Mode TON-1: Flicker ON start 2 (Timer does not reset when power comes ON)
Timing starts when the start signal goes ON.
The status of the control output is reversed when time is
up (ON at start).
While the start signal is ON, the timer starts when the
power comes ON or when the reset input goes OFF.
Basic Operation
Power
*
Start signal
input
Timing
ON
Timing
OFF
Timing
ON
a
b
Output
(a + b = OFF time)
* Start signal input is disabled during timing.
Note: Normal output operation will not be possible if
the set time is too short.
Gate not included on any mode of this Relay.
72
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HX Plug-in Timing Relay
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
48×48
7.5
14.3
63.7
44.8×44.8
60 min.
45 +0.6
−0
45 +0.6
−0
60 min. 15 min.
Cat. No. 700-HX…
Panel Cutout
5.2
(13/64)
6.2
(15/64)
50
(1-63/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
Terminal Arrangement
Internal circuit
Signal
Reset
4
5
3
6
7
2
1
8
0V
(–)
(+)
Cat. No. 700-HX…
Rockwell Automation Publication 700-TD552A-EN-P
73
700-HXM Plug-in Timing Relay
Relays and Timer Specifications
Bulletin 700-HXM — Preset Counter/Timing Relay
General Timer Functions
Operation Display 2
No. 1 Display
Indicator
Meaning
RST
Lit during reset using reset
input or Reset Key.
OUT
Lit when control output is ON.
TOTAL
Lit when totalizing value is displayed.
Displays the present value or
parameter type. When totalizing count
is displayed, the leftmost four digits of the
8-digit totalizing count will be displayed
(Zeros suppressed).
Operation Display 1
Displays the time unit when
the timer function
has been selected
Example
No. 2 Display
Displays set value
or set value of the parameter.
Displays the rightmost four digits
of the count value when the
700-HXM is used as a totalizing counter
(Zero suppressed).
5 h 30 min
123.4 s
Level Key
Displays the present
value or parameter type.
When totalizing count is
displayed, the leftmost four
digits of the 8-digit
totalizing count will be
displayed (Zeros
suppressed).
74
Mode Key
Press this key to select
parameters within
each level.
Down Key
Each press of this key
decreases values
displayed on the No. 2
display. Hold down this key
continuously to decrease
values quickly. Also returns
setting items.
Up/Reset Key
Each press of this key increases values displayed on
the No. 2 display. Hold down this key continuously to increase
values quickly. Also advances setting items.
To reset the present value, press this key while the present value
is displayed. If this key is pressed while the totalizing count value is
displayed, the totalizing count value and the present value will be reset.
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HXM Plug-in Timing Relay
Specifications
Electrical Ratings
Pilot Duty Rating
NEMA B300
Rated Supply Voltage
24V DC
Operating Voltage Range
85…110% of rated supply voltage
Power Consumption
1.5 W max. (for max. DC load) (Inrush current: 15 A max.)
120V AC
Make
Break
30 A
240V AC
15 A
120V AC
3A
240V AC
1.5 A
Hp at 120V AC
1/4 Hp
Hp at 240V AC
1/3 Hp
Mechanical
Mounting Method
Flush mounting (Panel or door)
Terminal Screw Tightening Torque
0.5 N•m max.
Display
Seven-segment, negative transmissive LCD; time display (hr, min, s); CMW,
OUT, RST, TOTAL
Present value (red, 7 mm high characters); Set value (green, 3.4 mm high
characters)
Digits
PV: Four digits
SV: Four digits
When total count value is displayed: eight digits
(Zeros suppressed)
Memory Backup
Counter
EEPROM (non-volatile memory) (number of writes: 100 000 times)
Maximum counting speed
30 Hz or 5 kHz
Counting range
-999…9,999
Input modes
Increment, decrement, individual, quadrature inputs
Output modes
N, F, C, or K
Time ranges
0.000…9.999 s, 0.00…99.99 s, 0.0…999.9 s, 0…9999 s, 0 min
00 s…99 min 59 s, 0.0…999.9 min, 0 h 00 min…99 h 59 min,
0.0…999.9 hr, 0 h…9999 hr
Timer
Inputs (OV input)
Control Output
Timer modes
Elapsed time (Up), remaining time (Down)
Output modes
A, B, D, E, F, or Z
Input signals
For Counter: CP1, CP2, and reset
For Timer: Start, gate, and reset
Input method
No-voltage input (contact short-circuit and open input)
Short-circuit (ON) impedance: 1 KΩ max. (Approx.
2 mA runoff current at 0Ω)
Short-circuit (ON) residual voltage: 2V DC max.
Open (OFF) impedance: 100 kΩ min.
Applied voltage: 30V DC max.
Start, reset, gate
Minimum input signal width: 1 or 20 ms (selectable)
Power reset
Minimum power-opening time: 0.5 s
SPDT contact output: 5 A at 250V AC/30V DC, resistive load (cos φ = 1)
Minimum Applied Load
10 mA at 5V DC (failure level: P, reference value)
Reset System
External, manual, and power supply resets (for timer in A, B, D, E, or Z modes)
Sensor Waiting Time
260 ms max. (Inputs cannot be received during sensor wait time if control
outputs are turned OFF.)
The figures given for maximum counting speed are for incrementing or decrementing operation with a prescale value of x1. If prescaling is used and 5 kHz is
set, the maximum counting speed will be reduced to about half. The non-prescaling maximum counting speed will also be reduced to about half when the
up/down mode is selected.
‡ “700-HXM User Manual” pub. no. 700-UM001*
Rockwell Automation Publication 700-TD552A-EN-P
75
700-HXM Plug-in Timing Relay
Relays and Timer Specifications
Characteristics
Signal start: ±0.03% ±30 ms max.
Power-ON start: ±0.03% ±50 ms max.
Timer Function
Insulation Resistance
100 mΩ min. (at 500V DC)
Dielectric Strength
1500V AC, 50/60 Hz for 1 min between output terminals and non-current-carrying metal parts
510V AC, 50/60 Hz for 1 min between current-carrying terminals (except output terminals) and
non-current-carrying metal parts
1500V AC, 50/60 Hz for 1 min between output terminals and current-carrying terminals (except
output terminals)
500V AC, 50/60 Hz for 1 min between communications terminals and current-carrying terminals
(except output terminals)
1000V AC, 50/60 Hz for 1 min between contacts not located next to each other
Noise Immunity
Square-wave noise by noise simulator;
±480V (between power terminals), ±600 V (between input terminals)
Static Immunity
±8 kV (malfunction), ±15 kV (destruction)
Vibration Resistance
Malfunction
10…55 Hz with 0.35 mm single amplitude each in three directions for 10 min.
Shock Resistance
Malfunction
100 m/s2 (approx. 10 G), 3 times each in six directions
Mechanical
10 million operations
Electrical
100 000 operations min (3 A at 250V AC, resistive load)
Life Expectancy
Ambient Temperature
Operating
-10…55 °C (with no icing or condensation)
Storage
-25…65 °C (with no icing or condensation)
Ambient humidity
25…85%
EMC
(EMI):
Emission Enclosure: EN61326 Class A
(EMS): EN61326
Immunity ESD:EN61000-4-2:4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference:EN61000-4-3:10 V/m (Amplitude-modulated,
80 MHz…1 GHz) (level 3);
10 V/m (Pulse-modulated,
900 MHz ±5 MHz) (level 3)
Immunity Conducted
Disturbance:EN61000-4-6:3 V (0.15…80 MHz) (level 2)
Immunity Burst:EN61000-4-4:2 kV power-line (level 3);
1 kV I/O signal-line (level 4);
1 kV communications-line (level 3)
Immunity Surge:EN61000-4-5:1 kV between lines
(power and output lines) (level 3);
2 kV between grounds
(power and output lines) (level 3)
Enclosure Ratings
Panel surface: IP66 and NEMA Type 4 (indoors)
Rear case: IP20
Terminal block: IP20
Weight
Approx. 80 g
Certifications
cURus Recognized Component (File No. E14843, Guide NRNT2/NRNT8), CE Marked, C-Tick
Marked
Standards
EN61010-1, EN 61326, UL 508, CSA C22.2 No. 14
76
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HXM Plug-in Timing Relay
Input/Output Modes and Count Values
Up (Increment) Mode CP1: Count Input
Down (Decrement) Mode CP1: Count Input
CP2: Count Prohibit input
CP1
CP1
CP2
CP2
CP2: Count prohibit input
UP
Count
Input
edge
CP1
H
L
CP2
H
L
CP1: Count Input
CP2: Count prohibit input
CP1: Count input
CP2: Count prohibit input
CP1
CP2
DOWN
Count
Count
Up/Down C Quadrature Input
Up/Down B Individual Input
CP1
CP1
CP2
CP2
Count
Count
Note: H = Short-circuited
L = Open
(A) indicates the minimum signal width and (B) requires at least 1/2 the minimum signal width. If these conditions are not met, a counting error
(+1 or -1) may occur.
Rockwell Automation Publication 700-TD552A-EN-P
77
700-HXM Plug-in Timing Relay
Relays and Timer Specifications
Input/Output Mode Settings
Counter Function
If there is a power failure during output ON, output will turn ON again when the power supply has recovered. For one-shot output, an output
will be made again for the duration of the output time setting once the power supply has resumed. Output timing restarted during one-shot
outputs is ignored.
Input Mode
Up
Down
Up/Down B.C
Reset
9999
SV
N
0
-999
Output
Reset
9999
SV
F
0
-999
Output
Output
mode
Reset
9999
SV
C
0
-999
t
t
t
t
t-a
t
t
t-a
t
Output
Reset
9999
SV
K
0
-999
t-a
t
t-a
t-a
t
t-a
t
Output
Note: t-a: Less than the output time
t: Output time
Totalizing Counter Operation
Reset
Totalizing Count Reset
(Reset Key)
PV
Totalizing counter continues to count the present value, regardless
of whether an reset input (by the reset key) has been made to
reset the PV.
When totalizing count value has reset, the PV is reset at the same
time.
The totalizing count range is 0…99999999. If the totalizing count
exceeds 99999999, the count returns to 0. If the count drops
below 0, it becomes 99999999.
Totalizing Count Value
78
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-HXM Plug-in Timing Relay
Timer Function
A Mode: Signal ON-Delay
B Mode: Repeat Cycle
Power
supply
Start
Start
Gate
Gate
Reset
Control
output
SV
Up
0
SV
Down
0
Reset
Control
output
SV
Up
0
SV
Down
0
Time display
Time display
Power
supply
D Mode: Signal OFF-Delay
E Mode: One Shot
Power
supply
Start
Start
Gate
Gate
Reset
Control
output
SV
Up
0
SV
Down
0
Reset
Control
output
SV
Up
0
SV
Down
0
Time display
Time display
Power
supply
F Mode: Accumulative
Z Mode: ON/OFF-Duty Adjustable Repeat Cycle
Power
supply
Power
supply
Start
Start
Gate
Time display
Time display
Gate
Reset
Control
output
SV
Up
0
SV
Down
0
Reset
Control
output
Cycle time
ON duty setting
(%) ON time
Up
0
Cycle time
ON duty setting
(%) ON time
Down
0
Z Mode
Output quantity can be adjusted by changing the cycle time set in the adjustment level to 1 and by changing the ON duty (%) set value.
The set value shows the ON duty (%) and can be set to a value between 0 and 100 (%). When the cycle time is 0, the output will always be
OFF. When the cycle time is not 0 and when ON duty has been set to 0 (%), the output will always be OFF. When ON duty has been set to
100 (%), the output will always be ON.
Cycle time
ON duty (%)
Cycle time
One-shot output or HOLD output can be selected for output:
Rockwell Automation Publication 700-TD552A-EN-P
79
700-HXM Plug-in Timing Relay
Relays and Timer Specifications
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
Cat. No. 700-HXM…
Terminal Arrangement
RS-485
Not
Not
Connected
connected
Output
Output
Out
CP1/
Start
24-VDC
24V DC
power supply
power
supply
CP2/
Gate
Reset
Reset
Contact
inputs
Contact Inputs
Open-collector
inputs
Open-collector
inputs
Cat. No. 700-HXM…
80
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-P Industrial Relays
Type
Standard Cartridge
Master Cartridge
Heavy duty
Bulletin No.
700-P
700-PMKIT
700-PHDKIT
10 A @ 600V AC
5 A @ 600V DC
20 A @ 600V AC
10 A @ 600V DC
35 A @ 600V AC
20 A @ 600V DC
AC
NEMA A600
2 x NEMA A600
2 x NEMA A600
DC
NEMA P600
N150 P600
N150 P600
Electrical
Contact Rating Continuous
Ratings
Make/Break
Additional Contact Ratings for
AC single-phase loads
3 Hp @ 240V AC - N.O.
5 Hp @ 240V AC - N.O.
2 Hp @ 240V AC - N.O./N.C.
3 Hp @ 240V AC - N.O./N.C.
1 Hp @ 120V AC - N.O./N.C.
2 Hp @ 120V AC - N.O./N.C.
20 A Resistive Heating to 600V AC
35 A General Use At 0.75 PF to 600V AC
20 A Tungsten Lighting Load to 480V AC 35 A Tungsten Lighting Load to 480V AC
—
DC Current
Ratings Make/Break
Cartridge Cat. No. 700-CP1
Cartridge Cat. No. 700-CPM
Cartridge Cat. No. 700-CPH
Volts DC
Contacts in
Series
DC Switching
Inductive Load
24
64
125
Coil
Consumption
600
24
64
125
250
500
5A
2.2 A 1.1 A .55 A .24 A
.2 A
10 A
5A
2
10 A
10 A
5A
2A
.7 A
.5 A
20 A
10 A
5A
2A
.7 A
3
—
—
7A
3A
1.5 A 1.0 A
—
15 A
7A
3A
4
—
—
10 A
5A
2.5 A 1.5 A
—
20 A
10 A
5A
2.2 A .55 A .24 A
85…110%
600
24
64
125
250
500
.2 A
10 A
5A
.5 A
20 A
10 A
2.2 A .55 A .24 A
5A
2A
.7 A
1.5 A 1.0 A
—
15 A
7A
3A
1.5 A 1.0 A
2.5 A 1.5 A
—
20 A
10 A
5A
2.5 A 1.5 A
85…110%
80…110%
80…110%
80…110%
85…115%
85…115%
85…115%
50 Hz
60 Hz
50 Hz
60 Hz
50 Hz
60 Hz
132VA‡
138VA‡
132VA‡
138VA‡
132VA‡
138VA‡
19VA‡
19.3 VA‡
19VA‡
19.3VA‡
19.3VA‡
12.7VA‡
12.7VA‡
12.7VA‡
.2 A
.5 A
85…110%
Battery
Charging
D Inrush
C Sealed
600
480W 480W 275W 138W 135W 120W
DC
A Inrush
C Sealed
PLL - PKLL
AC Latch Unit
500
1
AC
Coil Voltage
Range
250
19VA‡
12.7VA‡
12.7VA‡
12.7VA‡
Inrush
15VA‡
15.6VA‡
5VA‡
15.6VA‡
15VA‡
Sealed
5.4VA‡
5.5VA‡
5.4VA‡
5.5VA‡
5.4VA‡
15.6VA‡
5.5VA‡
PLL - PKLL
DC Latch Unit
Unlatch
35VA‡
35VA‡
Intermittent
35 W‡
35 W‡
—
Reset Time
PT – PKT
75 ms
75 ms
—
Minimum Pulse
PLL–PKLL
75 ms
75 ms
—
—
Mechanical
Pickup
AC – 10…20 ms
DC – 30…50 ms
AC – 10…20 ms
DC – 30…50 ms
AC – 10…20 ms
DC – 30…50 ms
Dropout
AC – 10…20 ms
DC – 20…33 ms
AC – 10…20 ms
DC – 20…33 ms
AC – 10…20 ms
DC – 20…33 ms
Operating Time
Mechanical Life
10 million operations
Construction
Contact Arrangement
Contact Material
Mounting
Up to 12 Poles, Convertible to N.O. or
N.C. (8 N.C. Maximum)
Up to 12 Poles, Convertible to N.O. or
N.C. (8 N.C. Maximum)
Up to 6 Poles, Convertible to N.O. or
N.C. (4 N.C. Maximum)
Silver Nickel
Silver Cadmium Oxide
Silver Cadmium Oxide
Panel, Strip Mount, or DIN Rail
Horizontal Mounting Recommended
Panel, Strip Mount, or DIN Rail
Horizontal Mounting Recommended
Panel, Strip Mount, or DIN Rail
Horizontal Mounting Recommended
Environmental
Temperature
Operating
–20…+65 °C (–4…149 °F)
–20…+65 °C (–4…149 °F)
–20…+65 °C (–4…149 °F)
Storage
–40…+65 °C (–40…149 °F)
–40…+65 °C (–40…149 °F)
–40…+65 °C (–40…149 °F)
Wire Terminations
Wire size per UL/CSA
#18 AWG…(2) #12 AWG
Tightening Torque
8…12 lb•in (0.9…1.4 N•m)
Temperature inside the panel.
‡ Average value for all coils within range. For values on a specific coil voltage, contact your local Rockwell Automation sales office or Allen-Bradley distributor.
International Symbol for Mechanically Linked Contacts
Rockwell Automation Publication 700-TD552A-EN-P
81
700-P Industrial Relays
Relays and Timer Specifications
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
Bulletin 700-P Relays with standard, master contact, or heavy-duty contact cartridge
103.43 (4-5/64)
— 171.68 (6-49/64)
1/2
2.77
(7/64)
2.77
(7/64)
2- and 4-pole Bulletin 700-P Relay
Approximate Shipping Weight: AC – 0.68 kg (1.5 lb), DC – 1.34 kg (2.95 lb)
2- and 4-pole Bulletin 700-P with Pneumatic Time Delay Attachment
Approximate Shipping Weight: AC – 0.85 kg (1.88 lb), DC – 1.5 kg (3.33 lb)
AC 136.75 (5-25/64)
171.68 (6-49/64)
2.77
(7/64)
2.77
(7/64)
6- and 8-pole Bulletin 700-P Relay with one -PB adder deck
Approximate Shipping Weight:
AC – 0.79 kg (1.75 lb), DC – 1.45 kg (3.20 lb)
Bulletin 700-P Relay with Mechanical Latch
Attachment Approximate Shipping Weight:
AC – 0.97 kg (2.13 lb), DC – 1.62 kg (3.58 lb)
170.10 (6-45/64)
Cat. No. 700
2.77
(7/64)
#8 Screws
(Captive)
Bulletin 700-P Relay, up to 12 poles with -PB and -PC adder decks
Approximate Shipping Weight: AC – 1.02 kg (2.25 lb), DC – 1.68 kg (3.7 lb)
Relay Rail for Bulletin 700-P, -N, -NM, -R, -RM, -RT, -RTA Relays
Secure the mounting strip with two screws at each end relay position.
Use a minimum of one screw at the 3rd, 5th, 7th, etc., relay positions.
Alternate between upper and lower horizontal slots.
178.60
(7-1/32)
AC – 170.49 (6-23/32)
DC – 187 (7-25/64)
700-PS
Timer
Cat. No. 700-N31, Type 1 Enclosure for
Bulletin 700-P, -RTC Relays
Approximate Shipping Weight: 1.26 kg (2.8 lb)
5.2
(13/64)
6.2
(15/64)
50
(1-63/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
1000
(39-3/8)
Bulletin 700-PS Timer Mounted on a Bulletin 700-P Relay
Approximate Shipping Weight: AC – 0.68 kg (1.5 lb) without 700-PS,
eDC – 1.34 kg (2.9 lb) without 700-PS
3.98
(0.16)
27.0
(1.06)
7.5
(0.3)
0.5
(.02)
2.25
(0.09)
0.5
(.02)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Cat. No. 199-DR4 DIN Mounting Rail Series B Has No Mounting Holes
82
Rockwell Automation Publication 700-TD552A-EN-P
DIN Rail Adapter
Relays and Timer Specifications
700S-P Industrial Relays
Type
Type
700S-P
700S-PK
Electrical
Electrical
Contact Rating
Continuous
Ratings
Make/
Break
AC
NEMA A600
DC
NEMA P600
Minimum Contact
Switching Ratings
DC
Switching
Volts DC
24V
64V
125V
250V
500V
600V
5A
2.2 A
1.1 A
0.55 A
0.24 A
0.2 A
2
10 A
10 A
5A
2A
0.7 A
0.5 A
3
—
—
7A
3A
1.5 A
1.0 A
—
—
10 A
5A
2.5 A
NEMA A600
DC
NEMA P600
Additional Contact
Ratings for AC
Single-Phase Loss
DC Current Ratings
Make/Break
Cartridge Cat. No. 700-CMS
DC
Switching
Volts DC
Contacts
in Series
24V
64V
125V
250V
500V
600V
1
10 A
5A
2.2 A
0.55 A
0.24 A
0.2 A
2
20 A
10 A
5A
2A
0.7 A
0.5 A
3
—
15 A
7A
3A
1.5 A
1.0 A
—
20 A
10 A
5A
2.5 A
1.5 A
85…110%
4
DC
80…110%
AC
85…110%
Battery
Charging
85…115%
DC
80…110%
50 Hz
60 Hz
Inrush
132 VA
138 VA
Sealed
19.3 VA
19 VA
Inrush
12.7 W
Sealed
12.7 W
Coil
Voltage
Range
AC
DC
All contacts are mechanically linked per IEC 9475-1 annex L for 2 to 12 poles
Pickup
AC – 10…20 ms
DC – 30…50 ms
Dropout
AC – 10…20 ms
DC – 20…33 ms
Mechanical Life
Battery
Charging
Coil Consumption
Mechanical
Mechanically Linked
Contacts
Operating
Time
AC
3 Hp @ 240V AC - N.O.
2 Hp @ 240V AC - N.O./N.C.
1 HP @ 120V AC - N.O./N.C.
20 A resistive heating to 600V AC
20 A Tungsten lighting load to 480V AC
1.5 A
1.5 million operations at 10A break at 120V AC
14 million operations at 1A break at 120V AC
6 million operations at 1A break at 24V DC
20 A @ 600V AC
10 A @ 600V DC
AC
Coil Consumption
DC
10V, 50 mA
1
Contact Electrical Life—
Resistive Loads
AC
Ratings
Make/
Break
Contacts
in Series
4
Coil
Voltage
Range
Contact Rating
Continuous
10 A @ 600V AC
5 A @ 600V DC
60 Hz
Inrush
132 VA
138 VA
Sealed
19.3 VA
Contact Material/Design
Mounting
Sealed
Mechanically Linked
Contacts
Operating
Time
AC – 10…20 ms
DC – 30…50 ms
Dropout
AC – 10…20 ms
DC – 20…33 ms
Contact
Material/Design
Silver Nickel/Bifurcated
Environmental
-20…+65 °C (-4…+149 °F)
Tightening Torque
Mechanical
(Mechanically-Linked
Contacts)
Mounting
2 to 12 Poles (8 N.C. Maximum)
Silver Cadmium Oxide
All contacts, are mechnically linked per IEC 947-5-1
Annex L for 2 to 12 poles
Panel mount or strip mount recommended
Environmental
Operating§
Temperature
Wire Terminations
Wire size per UL/CSA
All contacts are mechanically linked per IEC 947-5-1
annex L for 2 to 12 poles
Pickup
Contact Arrangement
Panel mount or mount on 700-MP Relay or DIN
Rail Horizontal Mounting Recommended
-40…+65 °C (-40…+149 °F)
12.7 W
Construction
2 to 12 Poles, Double Break Contacts
N.O. or N.C. (8 N.C. Maximum)
Storage Temperature
12.7 W
Mechanical
10 million operations
Operating Temperature§
19 VA
Inrush
Construction
Contact Arrangement
85…115%
50 Hz
#18 AWG…(2) #12 AWG
-20…+65 °C (-4…+149 °F)
-40…+65 °C (-40…+149 °F)
Wire Terminations
8…12 lb•in (0.9…1.4 N•m)
Coil voltage required for proper operation (percent of rated coil voltage).
§ Temperature inside the panel.
Wire size per UL/CSA
Tightening Torque
#18 AWG…(2) #12 AWG
8…12 lb•in (0.9…1.4 N•m)
Coil voltage required for proper operation (percent of rated coil voltage).
§ Temperature inside the panel.
Rockwell Automation Publication 700-TD552A-EN-P
83
700S-P Industrial Relays
Relays and Timer Specifications
Approximate Dimensions
Dimensions are shown in millimeters (inches). Dimensions are not intended for manufacturing purposes.
103.43 (4-5/64)
AC 136.75 (5-25/64)
1/2
2.77
(7/64)
2.77
(7/64)
2- and 4-pole Bulletin 700S-P Relay
Approximate Shipping Weight: AC – 0.68 kg (1.5 lb), DC – 1.34 kg (2.95 lb)
6- and 8-pole Bulletin 700S-P Relay
Approximate Shipping Weight: AC – 0.79 kg (1.75 lb), DC – 1.45 kg (3.20 lb)
170.10 (6-45/64)
Cat. No. 700
2.77
(7/64)
10- and 12-pole Bulletin 700S-P
Approximate Shipping Weight: AC – 1.02 kg (2.25 lb), DC – 1.68 kg (3.7 lb)
5.2
(13/64)
6.2
(15/64)
50
(1-63/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
1000
(39-3/8)
27.0
(1.06)
7.5
(0.3)
DIN Rail
84
Rockwell Automation Publication 700-TD552A-EN-P
#8 Screws
(Captive)
Relay Rail
Relays and Timer Specifications
700-N Industrial Relays
Bul. 700-N
Bul. 700-NT
Electrical Ratings
Rated Thermal Current Ith
10 A
Rated Insulation Voltage
300V
Contact Rating
Coil Voltage Range
10 A @ 300V AC, NEMA A300
AC
85…110%
—
DC
80…110%
—
Coil Consumption
AC
50 Hz
60 Hz
—
Inrush
120 VA
133 VA
—
Sealed
24 VA
20 VA
—
Mechanical
AC
—
Pickup
14 ms
—
Drop Out
13 ms
—
—
0.2…60 s
Repeat Accuracy
—
±15% of setting
Reset Time
—
75 ms
Timing Mode
—
On-Delay — convertible to OFF Delay, up to 2 poles
convertible to N.O. or N.C.
Max.
Operating Time
Timing Range
Construction
Contact Arrangement
Contact Material
Mounting
Up to 8 Poles, Convertible to N.O. or N.C.
—
Silver
Silver
Panel or strip mount
Horizontal mounting recommended
On relay only
Environmental
Ambient Temperature (Outside
Enclosure)
Operating Temperature Rise
(Inside Enclosure)
Operating
–20…+40 °C (–4…+104 °F)
Storage
–40…+60 °C (–40…+140 °F)
+25 °C Max
—
Wire Terminations
Wire size per UL/CSA
Tightening Torque
#18 AWG…(2) #12 AWG
8…12 lb•in. (0.9…1.4 N•m)
Rockwell Automation Publication 700-TD552A-EN-P
85
700-N Industrial Relays
Relays and Timer Specifications
Approximate Dimensions
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
Open Type
Without Enclosure
Type of Relay
No. of
Poles
Type 1
General Purpose Enclosure
Drawing
Number
A
Wide
B
High
C
Deep
D
Approx.
Ship. Wt.
kg (lbs.)
D
E
Approx.
Ship. Wt.
kg (lbs.)
88.90
(3-1/2)
82.55
(3-1/4)
79.38
(3-1/8)
0.68
(1-1/2)
107.95
(4-1/4)
185.74
(7-5/16)
103.19
(4-1/16)
146.05
(5-3/4)
85.73
(3-3/8)
1.59
(3-1/2)
A
Wide
B
High
C
Deep
Bulletin
700
2…4
1
57.15
(2-1/4)
Bulletin
700
6…8
2
57.15
(2-1/4)
88.90
(3-1/2)
106.36
(4-3/16)
79.38
(3-1/8)
0.79
(1-3/4)
112.71
(4-7/16)
228.60
(9)
120.65
(4-3/4)
206.38
(8-1/8)
92.08
(3-5/8)
2.27
(5)
N
with
Pneumatic
Timer
Bulletin
700
2…4
3
57.15
(2-1/4)
88.90
(3-1/2)
138.11
(5-7/16)
79.38
(3-1/8)
0.91
(2)
—
—
—
—
—
—
N
with
Solid-State
Timer
Bulletin
700
2…4
3
57.15
(2-1/4)
88.90
(3-1/2)
160.34
(6-5/16)
79.38
(3-1/8)
1.02
(2-1/4)
—
—
—
—
—
—
N
C
A
A
C
D B
A
C
D B
D B
Drawing Number 2
Drawing Number 1
Drawing Number 3
178.60
(7-1/32)
Cat. No. 700
#8 Screws
(Captive)
5.2
(13/64)
6.2
(15/64)
50
(1-63/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
7.5
(0.3)
1000
(39-3/8)
3.98
(0.16)
0.5
(.02)
2.25
(0.09)
0.5
(.02)
DIN Rail Adapter
86
Rockwell Automation Publication 700-TD552A-EN-P
27.0
(1.06)
Relays and Timer Specifications
700-R, -RM Sealed Switch Relays
Application Data – Because of the inherent characteristics of this device, the normally open contacts may close before the normally closed
contacts open on energization and the normally closed contacts may close before the normally open contacts open on de-energization.
Note: For Bul. 700-RM, energizing both the latch and unlatch coil together will cause the relay to be energized and both latch and unlatch
coils can be operated together continuously.
Ratings
AC Voltage
NEMA Rating
Designation
Voltage
Up to 300V
AC
B300
C600
Above 300V
AC
DC Voltage
Make
Break
120V
30
3
240V
15
1.5
480V
7.5
0.75
600V
6.0
0.60
Continuous
Carrying
Current [A]
NEMA Rating
Designation
5
Volts DC
Make/Break
Continuous
Carrying
Current [A]
46…300
138 VA
5
5…46
3A
5
NEMA P300
2.5
Maximum Allowable Off-State Leakage Current
Maximum Off-State Leakage
Current [mA]
Maximum Off-State Leakage
Current [mA]
Voltage
Type R
Type RM
24V DC
23
8
24V AC
23
8
120V AC
5
2
Relay Data
Type
700-R
Contact Arrangement
700-RM
Up to 8 poles, available in any combination of N.O. or N.C. contacts
Contact Material
W (tungsten in a controlled gas atmosphere)
24…250V AC
24…250V DC
Coil Voltage Range
Coil
Power
Sealed
Voltage Range: –15… +10%
5.5 VA, 50/60 Hz
5.5 W DC
1.7 VA, 50/60 Hz (latch or unlatch)
1.7 W DC
Inrush
5.5 VA, 50/60 Hz
5.5 W DC
1.7 VA, 50/60 Hz (latch or unlatch)
1.7 W DC
Pickup Time
30 ms
75 ms min. latch pulse
Dropout Time
30 ms
75 ms min. unlatch pulse
Operating Temperature
–40…+60 °C (–40…+140 °F)
Mounting
–40…+60 °C (–40…+140 °F)
Panel mount
Haz. Loc. Ratings
Class I, Division 2, Groups A, B, C, and D
Bulletin 700-R Operating Coils
Bulletin 700-R 2-…8-Pole AC
Coil Volts
Bulletin 700-R Operating Coil
60 Hz
50 Hz
Bulletin 700-R
2-…8-Pole DC
24
77AB27
77AB27
77D152
48
77AB134
77AB134
77D166
110
77AB86
77AB86
—
115…125
—
—
77D155
120
77AB86
77AB86
—
208
—
—
—
220
77AB83
77AB83
—
240
77AB83
77AB83
—
230…250
—
—
77D156
Rockwell Automation Publication 700-TD552A-EN-P
87
700-R, -RM Sealed Switch Relays
Relays and Timer Specifications
Dimensions are shown in millimeters (inches) shown. Dimensions are not intended to be used for manufacturing purposes.
C
A
C
B
C
A
B
D
Bulletin 700-R400…, -RM400…
A
B
D
Bulletin 700-R800, -RM800…
A
D
Bulletin 700-R with 852s timer
C
160.6 max
(6-21/64)
B
D
3.98
(0.16)
700-PS
Timer
700 Type R
E
Type 1 Enclosure
700-N26
2.25
(0.09)
0.5
(.02)
Cat. No. 700
0.5
(.02)
Secure the mounting strip with 2 screws at each
end relay position. Use a minimum of one screw at
the 3rd, 5th, 7th, etc., relay positions. Alternate
between upper and lower horizontal slots.
#8 Screws
(Captive)
Relay Rail
6.2
(15/64)
50
(1-63/64)
5.2
(13/64)
12.5
(1/2)
1.0
(0.04)
35.0
(1.38)
27.0
(1.06)
7.5
(0.3)
1000
(39-3/8)
Cat. No. 199-DR1 DIN Mounting Rail Series B
Bulletin 700-R, -RM Relays
Open Type
Without Enclosures
Type of Relay
R
Bulletin 700
and
Bulletin 700DC
R with
Bulletin 700
Bulletin 852S
and
Timer
Bulletin 700DC
RM
Bulletin 700
and
Bulletin 700DC
RM with
Bulletin 700
Bulletin 852S
and
Timer
Bulletin 700DC
88
Type 1
General Purpose Enclosure
Drawing
Number
A
Wide
B
High
C
Deep
D
Approx.
Ship Wt.
[kg (lb)]
D
E
Approx.
Ship Wt.
[kg (lb)]
2…4
1
55.56
(2-3/16)
88.90
(3-1/2)
92.25
(3-3/8)
79.38
(3-1/8)
0.91
(2)
104.78
(4-1/8)
185.74
(7-5/16)
103.19
(4-1/16)
146.05
(5-3/4)
85.73
(3-3/8)
1.81
(4)
5…8
2
55.56
(2-3/16)
88.90
(3-1/2)
111.13
(4-3/8)
79.38
(3-1/8)
1.02
(2-1/4)
112.71
(4-7/16)
228.60
(9)
120.65
(4-3/4)
206.38
(8-1/8)
92.08
(3-5/8)
2.49
(5)
2…4
3
55.56
(2-3/16)
88.90
(3-1/2)
165.1
(6-1/2)
79.38
(3-1/8)
1.25
(2-3/4)
—
—
—
—
—
—
2…4
1
55.56
(2-3/16)
88.90
(3-1/2)
95.25
(3-3/8)
79.38
(3-1/8)
0.91
(2)
104.78
(4-1/8)
185.74
(7-5/16)
103.19
(4-1/16)
146.05
(5-3/4)
85.73
(3-3/8)
1.81
(4)
5…8
2
55.56
(2-3/16)
89.90
(3-1/2)
111.13
(4-3/8)
79.38
(3-1/8)
1.02
(2-1/4)
112.71
(4-7/16)
228.60
(9)
120.65
(4-3/4)
206.38
(8-1/8)
92.08
(3-5/8)
2.49
(5)
2…4
3
55.56
(2-3/16)
88.90
(3-1/2)
165.1
(6-1/2)
79.38
(3-1/8)
1.25
(2-3/4)
—
—
—
—
—
—
No. of
Poles
A
Wide
B
High
C
Deep
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-RTC Industrial Relays
Voltage and Power Requirements
AC Voltage
+10% –15% 50/60 Hz
Total Power Required
Initiate Terminal Power
Maximum Allowable Leakage
Current
Coil Code
24V AC
8 VA
4 VA
10 mA
U24
110/120V AC
9 VA
4 VA
2.4 mA
U1
DC Voltage
+10% –20%
Total Power Required
Initiate Terminal Power
Maximum Allowable Leakage
Current
Coil Code
24V DC
10 W
5W
10 mA
U24
120V DC
11 W
5W
2.4 mA
U1
Type
Contact Rating
(See pub. 700-SG003*)
700-RTC
NEMA B600 600V AC, 5 A
NEMA P300 300V DC, 5 A
Contact Arrangement
1…4 poles. Max. of 2 timed and 2 instantaneous.
Available in any combination of N.O. and N.C. contacts
Contact Material
W (tungsten in a controlled gas atmosphere)
Operating Mode
Convertible to ON-Delay or OFF-Delay
Timing Range
0.015…64 minutes; 0.05...120 seconds
Reset Time
25 ms
Repeat Accuracy
±1% (or ±50 ms) at constant voltage and temperature
Mounting
Panel or strip mount
Surge Suppression
Not required. Timers have internal suppression
Haz. Loc. Ratings
Class I, Division 2, Groups A, B, C, and D
Maximum Allowable Leakage Current
24V AC/DC
10 mA
110/120V AC,
120V DC
2.4 mA
Ambient Temperature
Operating:
–20…+60 °C (–4…+140 °F)
Storage:
–20…+60 °C (–4…+140 °F)
Continuous duty units placed close to each other (3 in a row) have a temperature range of –20…+45 °C (–4…+113 °F) or should have air circulated around the
units. Approximate space of 3/4 in (mm) on all sides is needed.
Rockwell Automation Publication 700-TD552A-EN-P
89
700-RTC Industrial Relays
Relays and Timer Specifications
Typical Wiring Diagram
L1
External
Initiating Contact
(N.O. or N.C.)
Timed Contacts
Any Combination
of N.O. and N.C.
Instantaneous
Contacts Any
Combination of
N.O. and N.C.
L2
P TIMED
L1 +
INST
L2
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended to be used for manufacturing purposes.
5.2 (2-13/64) Dia. Mounting Holes
Approximate Shipping Weight 0.92 kg (2.1 lb.)
NEMA Type 1 Enclosure for RTC Relays
Approximate Shipping Weight 1.26 kg (2.8 lb.)
90
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-PS Industrial Relays
Specifications
Bulletin 700-PS
Operation
The timer must be energized continuously (L1-L2). ON-Delay: When the initiating contact closes, timing begins. At time-out, the output
contact closes. OFF-Delay: When the initiating contact closes, the output contact closes instantly. When the initiating contact re-opens,
timing begins. At time-out, the output contact re-opens.
Typical Wiring Diagram§
External
Initiating Contact
(See Attention)
Attention — To avoid damage to timer, do not switch any load
in addition to timing relay at terminals S1–S2. Do not apply an
external voltage to terminals S1–S2.
C1
Output
Contact
To Load
§ External Potentiometer units have R1, R2 terminals for
connecting the potentiometer.
S1
S2
Type PS Timer
C2
L1
L2
110/120V, 50/60 Hz
Approximate Dimensions
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
Bulletin 700-PS
Cat. No. 700-N25
2 Mounting Screws
with Springs
5.2 (13/64)
2 Mounting Slots
Bulletin 700-PS Timer Mounted on the Adapter Plate
Cat. No. 700-N25
Approximate Shipping Wt. 0.45 kg (1 lb)
Rockwell Automation Publication 700-TD552A-EN-P
91
700-PS Industrial Relays
Relays and Timer Specifications
160.6 max.
(6-5/16)
164.7 max.
(6-31/64)
700 Type P
700 Type R
700-PS
Timer
700-PS
Timer
Cat. No. 700-N26
Bulletin 700-PS Timer Mounted on a 4-Pole
Bulletin 700-P or -PK, or 2-Pole Bulletin 700-PH Relay
Approximate Shipping Wt. 1.02 kg (2.3 lb)
92
Bulletin 700-PS Timer Mounted on a 4-Pole
Bulletin 700-R or -RM Relay
Approximate Shipping Wt. 1.25 kg (2.8 lb)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-CF Control Relays
Assignment of Contacts
Device Combinations in Accordance with IEC 60947-1 / -4-1
Auxiliary Contact Blocks
Control Relays 700-CF (AC and DC Control)
700-CF⊗220
700-CF⊗310
A1 13 21 31 43
A1 13 21
K1
Circuit Diagram
Control
700-CF⊗400
A1 13 23 33 43
33 43
K1
A2 14 22 32 44
K1
A2 14 22 34 44
A2 14 24 34 44
Front Mounting 51 61
100-FA02
AC/DC
22E + 02E = 24Y
31E + 02E = 33Y
40E + 02E = 42Y
AC/DC
22E + 11E = 33Y
31E + 11E = 42Y
40E + 11E = 51Y
AC/DC
22E + 20E = 42Y
31E + 20E = 51Y
40E + 20E = 60Y
AC/DC
22E + 22E = 44Y
31E + 22E = 53Y
40E + 22E = 62Y
AC/DC
22E + 31E = 53Y
31E + 31E = 62Y
40E + 31E = 71Y
AC/DC
22E + 40E = 62Y
31E + 40E = 71Y
40E + 40E = 80Y
AC/DC
22E + L22E = L44Y
31E + L22E = L53Y
40E + L22E = L62Y
52 62
53 61
100-FA11
54 62
53 63
100-FA20
54 64
53 61 71 83
100-FA22
54 62 72 84
53 61 73 83
100-FA31
54 62 74 84
53 63 73 83
100-FA40
54 64 74 84
53 61 75 87
100-FAL22
54 62 76 88
Control relay and auxiliary contact block AC/DC max. 4 N. C.
700-CF (DC conventional coils), vertical mounting, 60 °C ♦
700-CF (AC and DC electronic coils), vertical mounting, 60 °C♦
Cat. No.
700…
Max.
N.O.
Side
Aux.
Max.
N.C.
Side
Aux.
Max.
N.O.
Front
Aux.
Max.
N.C.
Front
Aux.
Max.
N.O.
Front +
Side
Aux.
Max.
N.C.
Front +
Side
Aux.
Max.
N.O. +
N.C.
Front +
Side
Aux.
Cat. No.
700…
Max.
N.O.
Side
Aux.
Max.
N.C.
Side
Aux.
Max.
N.O.
Front
Aux.
Max.
N.C.
Front
Aux.
Max.
N.O.
Front +
Side
Aux.
Max.
N.C.
Front +
Side
Aux.
Max.
N.O. +
N.C.
Front +
Side
Aux.
8
CF400
2
4
4
4
6
7
8
CF400
2
2
4
4Δ
6
5
CF310
2
4♣
4
4Δ
6
5
8
CF310
2
2
4
4Δ
6
5
8
CF220
4
4♣
4
2
8
5
8
CF220
2
2
4
2
6
4
8
CF040
2
2
4
0
6
2
6
♣ With no front auxiliary contacts installed. Otherwise 3 N.C. Maximum
Δ With no side auxiliary contacts installed. Otherwise 3 N.C. Maximum
♦ For other operating conditions, please contact your local
Rockwell Automation sales office or Allen-Bradley distributor.
Δ With no side auxiliary contacts installed. Otherwise 3 N.C. Maximum
♦ For other operating conditions, please contact your local
Rockwell Automation sales office or Allen-Bradley distributor.
Rockwell Automation Publication 700-TD552A-EN-P
93
700-CF Control Relays
Relays and Timer Specifications
Cat. No. 100-JE
Cat. No. 100-JE12
Cat. No. 100-JE48
Electrical
Input Voltage
24V DC
12V DC
48V DC
Input Voltage Range
18…30V DC
6…12V DC
35…48V DC
110…240V AC
Output Voltage
110…240V AC
110…240V AC
Power Consumption
0.1…0.4 W
0.02…0.12 W
0.2…0.5 W
Minimum Actuation
5V DC, 2 mA DC
5V DC, 2 mA DC
5V DC, 2 mA DC
Mechanical
Finger Protection
IP20
IP20
IP20
Pickup Time
0…10 ms + pickup time
of the
contactor
0…10 ms + pickup time
of the
contactor
0…10 ms + pickup time
of the
contactor
Dropout Time
0…10 ms + dropout time 0…10 ms + dropout time 0…10 ms + dropout time
of the contactor
of the contactor
of the contactor
Max. Cycles Per Second
2
2
2
Isolation/Breakdown Voltage
In: 50V, Out: 250V
In: 50V, Out: 250V
In: 50V, Out: 250V
4 kV
4 kV
4 kV
Rated Impulse Withstand Voltage
Environmental
Ambient Temperature Range
-25…60 °C
-25…60 °C
-25…60 °C
Storage Temperature Range
-50…+80 °C
-50…80 °C
-50…80 °C
100+ million ops
100+ million ops
100+ million ops
Operating Life
Construction
1 Wire
0.5…2.5 mm2
0.5…2.5 mm2
0.5…2.5 mm2
2 Wire
0.75…2.5 mm2
0.75…2.5 mm2
0.75…2.5 mm2
Flexible wire
Wire Size Range
1 Wire
Solid wire
2 Wire
2
1.0…2.5 mm
2
1.0…2.5 mm2
2
1.0…2.5 mm2
1.0…2.5 mm
1.0…2.5 mm
1.0…2.5 mm
18…14 AWG
18…14 AWG
18…14 AWG
Tightening Torque
1…1.5 N•m/7…15 lb•in
1…1.5 N•m/7…15 lb•in
1…1.5 N•m/7…15 lb•in
Type of Light
LED
LED
LED
Solid and Stranded
To consider the maximum operations/hour of the relays.
94
2
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-CF Control Relays
Coils
AC Coil Code
Q
R
J
K
KJ
V
W
X
Y
KY
KP
D
KD
P
S
KG
H
L
KL
A
F
KF
VA
T
KA
I
E
N
KN
G
B
KB
M
C
50Hz
—
12V
—
24V
—
32V
36V
42V
48V
—
100V
110V
—
120V
127V
200V
—
200 - 220V
—
220V
220 - 230V
—
230 - 240V
240V
—
—
—
380 - 400V
—
400-415V
440V
—
500V
550V
AC Voltages
60Hz
12V
—
24V
—
—
36V
—
48V
—
—
100 - 110V
120V
—
—
—
200 - 220V
208V
208 - 240V
—
240V
260V
—
—
277V
—
347V
380V
440V
—
—
480V
—
—
600V
50/60Hz
—
—
—
—
24V
—
—
—
—
48V
100V
—
110V
—
—
200V
—
—
200 - 230V
—
—
230V
—
—
240V
—
—
—
400V
—
—
440V
—
—
Cat. No.
700-CF
TA006
TA404
TA013
TA407
TA855
TA481
TA410
TA482
TA414
TA860
TA861
TA473
TA856
TA425
TA428
TA862
TA049
TA296
TA864
TA474
TA441
TA851
TA440
TA480
TA858
TA065
TA067
TA071
TA863
TA457
TA475
TA859
TA479
TA476
DC Coil
Code
ZR
ZQ
DJ
ZJ
ZW
ZY
ZZ
ZB
ZG
ZE
ZD
ZP
ZS
ZA
ZF
ZT
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DC Voltages
9V
12V
24V Diode
24V
36V
48V
60V
64V
72V
80V
110V
115V
125V
220V
230V
250V
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Cat. No.
700-CF
TA766
TA708
TA714M
TA714
TA719
TA724
TA774
TA727
TA728
TA729
TA733
TA734
TA737
TA747
TA749
TA751
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Utilization Category Table from EN 60947-5-1
Verification of Making and Breaking Capacities of Switching Elements Under Normal Conditions
Corresponding to the Utilization Categories‡
Normal Condition of Use
Utilization
Category
Number and Rate of Making and Breaking
operations
Break§
Make§
I/Ie
U/Ue
cos ψ
I/Ie
U/Ue
cos ψ
No. operating
cycles♣
Operating cycles per
minute
AC-12♠
1
1
0.9
1
1
0.9
6050
6
0.05
AC-13♠
2
1
0.65
1
1
0.65
6050
6
0.05
AC-14♠
6
1
0.3
1
1
0.3
6050
6
0.05
AC-15♠
10
1
0.3
1
1
0.3
6050
6
0.05
DC
—
—
T0.95
—
—
T0.95
—
—
—
DC-12
1
1
1 ms
1
1
1 ms
6050
6
0.05♦
DC-13
1
1
6 x PΔ
1
1
6 x PΔ
6050
6
0.05♦
DC-14♠
10
1
15 ms
1
1
15 ms
6050
—
0.05♦
ON time [s]♦
Ie Rated operational current, I Current to be made or broken
Ue Rated operational voltage, U Voltage before make
PUeIe Steady-state power consumption (W)
T0.95 Time to reach 95% of the steady-state current (ms)
‡ See sub-clause 8.3.3.5.2.
§ For tolerances on test quantities, see sub-clause 8.3.2.2.
♣ The first 50 operating cycles shall be run at U/Ue=1.1 with the loads set at Ue.
Δ The value “6 x P” results from an empirical relationship which is found to represent most DC magnetic loads to an upper limit of P = 50 W, e.g., 6 x P= 300 W.
♦ The ON time shall be at least equal to T0.95.
♠ Where the break current differs from the make current value, the ON time refers to the make current value after which the current is reduced to the break
current value for a suitable period e.g., 0.05 s.
Rockwell Automation Publication 700-TD552A-EN-P
95
700-CF Control Relays
Relays and Timer Specifications
General
Main Relay
Cat. Nos.
700-CF, 700SCF
Front Mounted
Main Relay
Standard
Cat. No.
Auxiliary
700-CFB, 700SContacts
CFB
Master Relay
Cat. No.
700-CFM
Front Mounted
Bifurcated
Auxiliary
Contacts
Side-mounted
Auxiliary
Contacts
Contact Ratings — NEMA
A600, P600
A600, Q600
A600, Q600
2 x A600, P600
A600, Q600
A600, Q600
Min. Contact Rating
17V, 10 mA
17V, 5 mA
8V, 5 mA
—
5V, 3 mA
17V, 10 mA
24V
10 A
6A
3A
15 A
3A
6A
48V
10 A
6A
3A
15 A
3A
6A
120V
10 A
6A
3A
15 A
3A
6A
240V
10 A
5A
3A
15 A
3A
5A
400V
6A
3A
2A
7.5 A
2A
3A
480V/500V
2.5 A
1.6 A
1.2 A
5A
1.2 A
1.6 A
600V
1A
1A
0.7 A
2A
0.7 A
1A
690V
1A
1A
0.7 A
2A
0.7 A
1A
Ith
20 A
10 A
10 A
20 A
10 A
10 A
6A
6A
20 A
6A
6A
Contact Ratings — IEC AC-15
(solenoids, contactors) at rated
voltage
IEC 60947-5-1
40 °C
AC-12 (Control
of resistive
loads)
IEC 60947-5-1
60 °C
DC-12 Switching DC Loads
L/R < 1ms, Resistive Loads
IEC 60947-5-1
DC-13 IEC 60947-5-1, Solenoids
and contactors
230V
8 kW
400V
14 kW
690V
24 kW
Ith
20 A
230V
8 kW
400V
14 kW
690V
24 kW
24V
15 A
10 A
6A
20 A
6A
6A
48V
10 A
9A
3.2 A
20 A
3.2 A
3.2 A
110V
6A
3.5 A
1A
8A
1A
1A
220V
1A
0.7 A
0.5 A
1.5 A
0.5 A
0.5 A
440V
0.4 A
0.2 A
0.2 A
0.4 A
0.2 A
0.2 A
24V
5A
5A
2.5 A
5A
2.5 A
5A
48V
3A
3A
1.5 A
3A
1.5 A
2.5 A
110V
1.2 A
1.2 A
0.6 A
1.2 A
0.6 A
0.68 A
220V
0.6 A
0.6 A
0.3 A
0.6 A
0.3 A
0.32 A
440V
0.3 A
0.15 A
0.15 A
0.3 A
0.15 A
0.15 A
State of N.C. Contacts if N.O. contact welds
Location of welded N.O.
contacts
Main
Front aux.
Side aux.
Main
Open
Open
Open
Front aux.
Open
Open
—
Mechanically Linked
Contacts‡
Side mounted auxiliary contacts provide “mirror contact” performance with main poles only.
‡ Defined in IEC 60947-5-1 annex L. Mechanically linked is a relationship between contacts of opposite types (i.e., N.O. and N.C.).
Mechanical Life
Electrical Life
Cat. No.
700-CF
Aux./Pneu
matic
Timer
Contact
(Frontmounted)
DC Switching Ratings for 700-CF Main Poles in Series (Resistive Load at
60 °C)
1 pole
2 poles
24/48V
15/10 A
25 A
25 A
125V
6A
25 A
25 A
[Mil]
15
5
220V
1.5 A
8A
25 A
AC-15
(240V, 3 A)
[Mil]
1.5
1.5
440V
0.4 A
1A
3A
AC Coil
[g]
390
—
2 x A4
2 x A4
1.5…6
0.5…2.5
0.75…2.5
Weight
Terminal Cross-Sections
Terminal Type
Terminal Size per IEC60 947-1
Solid/
Stranded
1
Conductor
[mm2]
♣
2
Conductor
[mm2]
1.5…6
Max. Wire Size per UL/CSA
[AWG]
16…10
18…14
Tightening Torque
[lb·in]
13.3…17.7
8.9…13.3
Tightening Torque
[N·m]
1.5…2.0
1…1.5
♣ For 16 or more strands, end ferrule is required.
96
3 poles
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-CF Control Relays
Control Circuit
General
Cat. No. 700-CF
Cat. No. 700-CF
Operating Voltage
AC 50/60 Hz
DC
(conventional)
DC (electronic EQ, EW)
DC (electronic EY)
Rated Insulation Voltage Ui
Pickup
[x Us]
0.85…1.1
IEC
690V
Dropout
[x Us]
0.3…0.6
UL; CSA
600V
Pickup
[x Us]
0.8…1.1
Rated Impulse StrengthUimp
6 kV
Dropout
[x Us]
0.1…0.6
2500V
Pickup
[x Us]
0.7...1.25
High Test Voltage
1 minute (per IEC 60947-4)
Dropout
[x Us]
0.3...0.4
Pickup
[x Us]
0.8...1.25
Dropout
[x Us]
0.3...0.4
Rated Voltage Ue
AC
115, 230, 400, 500, 690V
DC
24, 48, 110, 220, 440V
Short-Circuit Protection gG Fuse 20 A
DC (electronic ED)
Pickup
[x Us]
0.7...1.12 ‡
Dropout
[x Us]
0.3...0.4
DC (electronic EA)
Pickup
[x Us]
0.8...1.1
Storage
–55…+80 °C (–67…176 °F)
Dropout
[x Us]
0.3...0.4
Operation at nominal current
–25…+60 °C (–13…140 °F)
15% current reduction
for AC-12 at > 60 °C
–25…+70 °C (–13…158 °F)
Corrosion Resistance
humid-alternating climate, cyclic,
per IEC 60068-2-30 and
DIN 50 016, 56 cycles
Altitude
2000 m above mean sea level, per
IEC60 947-4
Coil Consumption
AC 50/60 Hz
DC (conventional)
DC (electronic EQ, EJ)
DC (electronic EY)
DC (electronic ED)
DC (electronic EA)
Inrush
[VA]
75
Sealed
[VA/W]
9.5/2.7
Inrush
[W]
7.7
Rated Frequency
50/60 Hz, DC
Ambient Temperature
Sealed
[W]
6.3
Inrush (avg./
peak)
[W]
10/17
Sealed
[W]
1.7
IP2X (IEC 60529 and DIN 40050)
in connected state
Inrush (avg./
peak)
[W]
10/17
Shock Resistance
IEC 60068-2: Half sinusoidal shock
11 ms, 30 G (in 3 directions)
Sealed
[W]
1.9
Inrush (avg./
peak)
Vibration Resistance
[W]
12/19
IEC 60068-2: Static >2 G, in normal
position no malfunction <5 G
Type of Protection
Sealed
[W]
2.1
Inrush (avg./
peak)
[W]
14/22
Sealed
[W]
3.0
Operating Times
AC 50/60 Hz
Pickup Time
[ms]
15…30
Dropout Time
[ms]
10…60
40…70
Pickup Time
[ms]
Dropout Time
[ms]
7…15
With integrated
diode
Opening Delay
[ms]
14...20
With external
diode
Opening Delay
[ms]
70...125
Closing Delay
[ms]
25…50
Opening Delay
[ms]
27...45
DC (conventional)
DC (electronicEQ, EJ)
Min OFF time
[ms]
50
Max. ripple
DC (electronicEY, ED, EA)
± 15%
Closing Delay
[ms]
25...50
Opening Delay
[ms]
23...33
Min OFF time
[ms]
50
Max. ripple
± 15%
Latch Attachment Release, 100-FL
Coil Consumption
AC
[VA/W]
DC
[W]
25
[min./max]
0.03…15 s
Contact Signal Duration
45/40
Timing Attachment
Reset Time, 100ETA, 100-ETB
Repeat Accuracy
at min. time
setting
[ms]
at max. time
setting
[ms]
10
70
± 10%
For 9V DC, code ZR, use operating voltage 0.65…1.3 x Us.
For 24V DC, code ZJ, DJ, or EJ use operating voltage 0.7…1.25 x Us.
‡ At 110V DC, coil code ED has an operating voltage range of 0.7...1.25 x Us.
Rockwell Automation Publication 700-TD552A-EN-P
97
700-CF Control Relays
Relays and Timer Specifications
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended for manufacturing purposes.
Mounting Position
AC and DC Control Relay with DC Electronic Coil
Front View
May be mounted to 35 mm EN 50 022 DIN Rail.
Side View
DC Control Relay
Side View
Front View
AC and DC Control Relays with 12V or 24V DC Electronic Coil
Type
a
b
c
c1
c2
700-CF, -CFB,
-CFM
45
(1-25/32)
81
(3-3/16)
80.5
(3-11/64)
75.5
(3-3/32)
6
(1/4)
Ød
2 screws
4.5
(3/16)
d1
d2
60
(2-23/64)
35
(1-25/64)
d1
d2
60
(2-23/64)
35
(1-25/64)
d1
d2
60
(2-23/64)
35
(1-25/64)
DC Control Relays with 48...72V, 110...125V or 220...250V DC Electronic Coil
Type
a
b
c
c1
c2
700-CF, -CFB,
-CFM
45
(1-25/32)
105
(4-1/8)
80.5
(3-11/64)
75.5
(3-3/32)
6
(1/4)
Ød
2 screws
4.5
(3/16)
DC Control Relays with Conventional Coil
Type
a
b
c
c1
c2
700-CF, -CFB,
-CFM
45
(1-25/32)
81
(3-3/16)
106.5
(4-3/16)
101.5
(4)
6
(1/4)
Ød
2 screws
4.5
(3/16)
Accessories
AC Control Relay
Relay with
(inches)
mm
(inches)
c/c1 + 39
(c/c1 + 1 – 37/64)
c/c1 + 39
c/c1 + 1 – 37/64)
Auxiliary Contact for Front Mounting
2- or 4-pole
Auxiliary Contact for Side Mounting
1- or 2-pole
a+9
(a + 23/64)
a+9
(a + 23/64)
Pneumatic Timing Module
⎯
on coil terminal side
c/c1 + 58
(c/c1 + 2 – 23/64)
b + 24
(b + 15/16)
⎯
b + 24
⎯
(b + 15/16)
⎯
on coil terminal side
c/c1 + 61
(c/c1 + 2 – 31/64)
⎯
⎯
DC Interface
b+9
(b + 23/64)
Surge Suppressor
on coil terminal side
b+3
(b + 1/8)
⎯
b+3
⎯
(b + 1/8)
Labelling with:
label sheet
+0
(+0)
+0
(+0)
⎯
marking tag with cover
+0
(+0)
+0
(+0)
⎯
marking tag carrier for System V4/V5
+5.5
(+7/32)
+5.5
(+7/32)
⎯
marking tag carrier for System Bull.
1492W
+5.5
(+7/32)
+5.5
(+7/32)
Solid-state Timing Module
Mechanical Latching
98
DC Control Relay
mm
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700S-CF Control Relays
Cat. No.
Aux. Contact
700S-CF (Front-mounted)
Mechanical Life
[Mil]
15
15
[Mil]
1.5
1.5
[g]
390
⎯
2 x A4
2 x A4
[mm2]
1.5…6
0.5…2.5
[mm2]
1.5…6
0.75…2.5
Max. Wire Size per UL/CSA
[AWG]
16…10
18…14
Tightening Torque
[lb•in]
13.3…22
8.9…13.3
Tightening Torque
[N•m]
1.5…2.5
1…1.5
Electrical Life
AC-15
(240V, 3 A)
Weight
AC Coil
Terminal Cross-Sections
Terminal Type
Terminal Size per IEC 947-1
1 Conductor
Solid/
Stranded§ 2 Conductor
§ For 16 or more strands, end ferrule is required
DC Switching Ratings for 700S-CF Main Poles in Series
(Resistive Load at 60 °C)
1 pole
2 poles
3 poles
24/48V
15/10 A
25 A
25 A
125V
6A
25 A
25 A
220V
1.5 A
8A
25 A
440V
0.4 A
1A
3A
Assignment of Contacts
Safety Control Relays with Front-mount Auxiliary Contacts, 8-Pole AC or DC Coil Voltage
A1
53 61 71 81
53 61 71 83
53 61 73 83
54 62 72 82
54 62 72 84
54 62 74 84
A1
13 21 33 43
K1
13 21 33 43
K1
A2
14 22 34 44
700S-CF440……
700S-CFB440……
A1
13 21 33 43
A2
14 22 34 44
K1
A2
14 22 34 44
700S-CF530……
700S-CFB530……
Rockwell Automation Publication 700-TD552A-EN-P
700S-CF620……
700S-CFB620……
99
700S-CF Control Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters (inches). Approximate Dimensions are not intended for manufacturing purposes.
c2
c1
c
AC and DC Safety Control Relays with 12V or 24V DC Electronic Coil
Cat. No.
700S-CF
a
b
c
c1
c2
Ød
d1
45
81
119.5
114.5
6
2 - 4.5
60
d2
35
(1-25/32)
(3-3/16)
(4-3/4)
(4-43/64)
(1/4)
(2 - 3/16)
(2-23/64)
(1-25/64)
d2
DC Safety Control Relays with 48...72V, 110...125V or 220...250V DC Electronic Coil
Cat. No.
700S-CF
a
b
c
c1
c2
Ød
d1
45
105
119.5
114.5
6
2 - 4.5
60
35
(1-25/32)
(4-1/8)
(4-3/4)
(4-43/64)
(1/4)
(2 - 3/16)
(2-23/64)
(1-25/64)
d2
DC Safety Control Relays with Conventional Coil
Cat. No.
700S-CF
100
a
b
c
c1
c2
Ød
d1
45
81
145.5
140.5
6
2 - 4.5
60
35
(1-25/32)
(3-3/16)
(5-49/64)
(5-37/64)
(1/4)
(2 - 3/16)
(2-23/64)
(1-25/64)
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700S-CF Control Relays
Safety Relay Circuit With 5 Safety Outputs
Use for E-stop control. E-stop will work properly if any one fault occurs (a fault could be one welded contact or one undesired open
connection such as a loose wire).
High output switching capability and long contact life.
Circuit complies with EN 954 categories 1, 2, 3, 4.
Helps prevent restart of the 5 safety outputs if there is a single fault anywhere in the system.
Use (3) 700S-CF relays and this diagram to construct the circuit
Basic Circuit
(1) Output Circuit (3 Relays, 9 Terminal Blocks)
Basic Circuit
(1) Output Circuit (3 Relays, 9 Terminal Blocks)
Start
Push To Stop
Pull To Reset
Included in factory
wired units
LOAD 1
(5) Output Circuit (3 Relays, 17 Terminal Blocks)
LOAD 2
LOAD 3
LOAD 4
LOAD 5
Numbers shown are the line numbers where the contacts for this relay appear.
Contact your local Rockwell Automation sales office or Allen-Bradley distributor for availability.
Rockwell Automation Publication 700-TD552A-EN-P
101
700S-CF Control Relays
Relays and Timer Specifications
Accessories
Safety Control Relays with
mm
[in.]
Auxiliary contact block for side mounting 1- or 2-pole
a+9
(a + 23/64)
Electronic Timing Module on coil terminal side
b + 24
(b + 15/16)
Interface Module on coil terminal side
b+9
(b + 23/64)
Surge Suppressor on coil terminal side
b+3
(b + 1/8)
Labeling with label sheet
+0
(+ 0)
Marking tag sheet with clear cover
+0
(+ 0)
Marking tag adapter for System Bul. 1492W
+ 5.5
(+ 7/32)
Mounting Position
AC and DC E Safety Control Relays
Front View
102
Side View
DC Safety Control Relays
Front View
Side View
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-K Control Relays
Assignment of Contacts
Device Combinations in Accordance with IEC 60947-1 / -4-1
Table valid for : AC / DC = 0.85…1.1 x Us, Tamb. = -25 °C…+60 °C, normal position (horizontal rail mounting). Also valid for Bulletin 700-KR
relays and Bulletin 100-KR auxiliary contacts. Auxiliary Contact Blocks
Circuit Diagram
Control Relays 700-K (AC and DC Control)
Control
700-K22Z-⊗
700-K31Z-⊗
700-K40E-⊗
700-KL22Z-⊗
A1 13 43 21 31
A1 13 33 43 21
A1 13 23 33 43
A1 13 47 21 35
A2 14 44 22 32
A2 14 34 44 22
A2 14 24 34 44
A2 14 48 22 36
Front Mounting
51 61
100-KFA02E
AC/DC
—
31Z + 02E = 33Y ‡
40E + 02E = 42Y
—
AC/DC
22Z + 11E = 33Y
31Z + 11E = 42Y
40E + 11E = 51Y
L22Z + 11E = L33Y
AC/DC
22Z + 20E = 42Y
31Z + 20E = 51Y
40E + 20E = 60Y
L22Z + 20E = L42Y
AC/DC
—
—
40E + 04E = 44Y ‡
—
AC/DC
—
31Z + 13E = 44Y ‡
40E + 13E = 53Y
—
AC/DC
—
31Z + 22Z = 53Y ‡
40E + 22Z = 62Y
—
AC/DC
—
—
40E + 31Z = 71Y §
—
AC/DC
22Z + 40E = 62Y
31Z + 40E = 71Y
40E + 40E = 80Y
L22Z + 40E = L62Y
52 62
53 61
100-KFA11E
54 62
53 63
100-KFA20E
54 64
51 61 71 81
100-KFA04E
52 62 72 82
53 61 71 81
100-KFA13E
54 62 72 82
53 83 61 71
100-KFA22Z
54 84 62 72
53 73 83 61
100-KFA31Z
54 74 84 62
53 63 73 83
100-KFA40E
54 64 74 84
For other operating limits, please contact our technical consultant.
‡ Tamb. max. +40 °C
§ Tamb. max. +40 °C and only allowed for coil voltage 24V DC or 230V AC
Rockwell Automation Publication 700-TD552A-EN-P
103
700-K Control Relays
Relays and Timer Specifications
Auxiliary Contact Blocks
Connection
Diagrams
Description
Screw Type
Terminals
Spring Clamp
Terminals
Cat. No.
Cat. No.
N.O.
N.C.
For Use With
0
2
100/104-K,
700-K
1
100-KFA02E
100-KRFA02E
1
1
100/104-K,
700-K
1
100-KFA11E
100-KRFA11E
2
0
100/104-K,
700-K
1
100-KFA20E
100-KRFA20E
0
4
100/104-K,
700-K
1
100-KFA04E
100-KRFA04E
1
3
100/104-K,
700-K
1
100-KFA13E
100-KRFA13E
2
2
100/104-K,
700-K
1
100-KFA22Z
100-KRFA22Z
3
1
100/104-K,
700-K
1
100-KFA31Z
100-KRFA31Z
4
0
100/104-K,
700-K
1
100-KFA40E
100-KRFA40E
51 61
52 62
53 61
54 62
53 63
54 64
Front-mounted auxiliary contacts
Auxiliary Contact Blocks
2- and 4-pole versions
Choice of contact configurations
Snap on, no tools required
Electronic-compatible bifurcated
contacts for signals down to 15V/2 mA
Pkg.
Qty. 51 61 71 81
52 62 72 82
53 61 71 81
54 62 72 82
53 83 61 71
54 84 62 72
53 73 83 61
54 74 84 62
53 63 73 83
54 64 74 84
May be ordered in package quantities of 10. Add letter M to the end of the cat. no. Example: 100-KFA02EM.
Control Modules
Connection
Diagrams
Description
Mechanical Interlock
For interlocking of two adjacent contactors
No added width to contactor assembly
Front mount plug-in type
Optional auxiliary contact blocks and suppressor modules mount onto
the interlock
24…48V AC
RC Suppressor
110…280V AC
380…480V AC
Surge Suppressor
Plug-in type
Limits surge voltage on
coil drop-off
100/104-K/KR, 700-K/KR
100/104-K/KR, 700-K/KR
12…55V AC,
12…77V DC
MOV Suppressor
56…136V AC,
78…180V DC
100/104-K/KR, 700-K/KR
137…277V AC,
181…250V DC
Diode Suppressor
12…250V DC
May be ordered in package quantities of 10. Add letter M to the end of the cat. no. Example: 100-KFSC50M.
104
For Use With
Rockwell Automation Publication 700-TD552A-EN-P
100/104-K/KR, 700-K/KR
Pkg.
Qty.
Cat. No.
1
100-KMCH
1
100-KFSC50
1
100-KFSC280
1
100-KFSC480
1
100-KFSV55
1
100-KFSV136
1
100-KFSV277
1
100-KFSD250
Relays and Timer Specifications
700-K Control Relays
IEC Specifications
700-K
700-KR
AC-12 Rated Thermal Current
Ambient temperature 40°C
Ith
24…240V
[A]
10
230…500V
[A]
10
230…690V
[A]
10
Ambient temperature 60°C
Ith
24…240V
[A]
6
230…500V
[A]
6
230…690V
[A]
6
24V
[A]
3
48V
[A]
3
120V
[A]
3
230V
[A]
2
240V
[A]
2
400V
[A]
1.2
480V
[A]
1
500V
[A]
1
600V
[A]
0.6
690V
[A]
0.6
[A]
10
AC-15/B600
Switching of Solenoids and contactors
Ie
Short-circuit Protection
"gG" Fuse acc. to IEC 60947-5-1, no welding of contacts
Fuse gG
Min. Switching Capacity 15V
For bifurcated contacts (control relays and auxiliary contact blocks)
[mA]
2
[mΩ]
6.5
[W]
2.6
AC control, warm
[W]
4.4
DC control, warm
[W]
5.2
Resistance and Power Dissipation
Main current circuit resistance, 1 pole
Power dissipation, 4 poles
Total power dissipation
Lifespan
Mechanical
[Mio. op.]
15
Electrical AC-15 (240V / 2 A)
[Mio. op.]
0.7
Weight
AC control
kg (lbs.)
0.16 (0.35)
DC control
kg (lbs.)
0.2 (0.44)
Load Carrying Capacity per UL/CSA
Rated voltage
AC
[V]
40 °C
[A]
Switching capacity
AC
[A]
B 600
Rated voltage
DC
[V]
max. 600
Switching capacity
DC
[A]
Q 600
Continuous rating
max. 600
10
Rockwell Automation Publication 700-TD552A-EN-P
6
105
700-K Control Relays
Relays and Timer Specifications
700-K
DC-13/Q600
1 pole
24V
[A]
48V
[A]
2.3
1
110V
[A]
0.55
125V
[A]
0.55
220V
[A]
0.27
250V
[A]
0.27
400V
[A]
0.15
440V
[A]
0.15
600V
[A]
0.1
Cross Sections
Conductor Cross Sections
- Main Contacts, Auxiliary Contacts, and Coil
Terminals
700-K
700-KR
Terminal type
Fine stranded
with ferrule
(1) Conductor
(2) Conductors
[mm2]
[mm2]
0.75…2.5
0.75…2.5
0.50…2.5
0.50…2.5
Solid or coarse
stranded
(1) Conductor
(2) Conductors
[mm2]
[mm2]
1…4
1…2.5 + 1…4
0.75…2.5 ♣
0.75…2.5 ♣
Recommended torque
Cross section per UL/CSA
Recommended torque
1.2
—
[AWG]
[Nm]
18…12 ‡
18…14 ♣
[lb-in]
10.6
—
Pozidriv No. 2 / Blade No. 3 screw
‡ Use same cross sections
♣ Stranded wire only
106
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-K Control Relays
Coil Data
700-K
Operating Limits
AC control
50 Hz, 60 Hz, 50/60 Hz
DC control
pick-up
[x Us]
0.85…1.1
dropout
[x Us]
0.2…0.75
pick-up
[x Us]
0.8…1.1
9, 12, 24, 110V DC: 0.7…1.25
dropout
[x Us]
0.1…0.75
pick-up
[VA/W]
35/32
hold-in
[VA/W]
pick-up
[W]
cold 3.0, warm 2.6
hold-in
[W]
cold 3.0, warm 2.6
closing delay
[ms]
15…40
opening delay
[ms]
15…33
opening delay
[ms]
15…28
closing delay
[ms]
18…40
6…12
Coil Consumption
AC control
50 Hz, 60 Hz, 50/60 Hz
DC control
5/1.8
Operating Times
AC
With RC module
DC
opening delay
[ms]
With integrated diode
opening delay
[ms]
8…12
With external diode
opening delay
[ms]
35…50
Rockwell Automation Publication 700-TD552A-EN-P
107
700-K Control Relays
Relays and Timer Specifications
Approximate Dimensions
Approximate Dimensions are shown in millimeters. Approximate Dimensions are not intended for manufacturing purposes.
(mm)
12
35
45
4
35.2
*)
*) -Minimum distance to grounded parts or walls
49
79
108
180°
54
56
50
25° 25°
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SA Solid State Relays
Control/Input Ratings
Rated Control
Voltage
Cat. No.
700-SAZY5Z25
700-SANY3Z25
Control Voltage Levels
Max. Operating
Control Voltage Range
Max. Reverse
Control Voltage
Impedance
4…32V DC
-32V DC
15 mA max.
4…30V DC
-30V DC
1.5 kΩ (+20% -10%)
5…24V DC
Pick-up Voltage
Drop-out Voltage
4V DC max.
1V DC min.
Load/Output Ratings
Continuous Load Current (Resistive) [A]
Cat. No.
Rated Load Voltage
Maximum Load
Voltage Range
Min.
Max
Max. Inrush Current‡
700-SAZY5Z25
100…240V AC
75…264V AC
0.1
5.0
80 A, @ 50/60 Hz
for 1 cycle
700-SANY3Z25
5…110V DC
3…125V DC
0.1
3.0
12 A (10 ms)
Characteristics
Description
Cat. No. 700-SAZY5Z25
Load Switching Method/Device
Cat. No. 700-SANY3Z25
Triac
Transistor
Pick-up Time
1/2 cycle of load power source cycle time§ + 1 ms
max.
0.5 ms max.
Drop-out Time
1/2 cycle of load power source cycle time§ + 1 ms
max.
2.5 ms max.
Output ON Voltage Drop
1.6V (RMS) max.
1.5V max.
Output Leakage Current
5 mA max. (at 100V AC); 10 mA max. (at 200V AC)
5 mA max. (at 125V DC)
Output VDRM VCEO (V)
600
150
Output di/dt (A/uS)
50
—
Output dv/dt (V/uS)
500
—
Output I2t (A2S)
41.6
—
Output Tj (ºC) Max.
125
150
Insulation Resistance
100 MΩ min. (at 500V DC)
Dielectric Strength
1500V AC, 50/60 Hz for 1 min
Vibration Resistance (Max.)
10…55 Hz, 1.5 mm double amplitude (10 G)
1000 m/s2 (100 G)
Shock Resistance (max.)
Ambient Temperature
Operating
–30…80 °C (–22…176 °F) with no icing or condensation
Storage
–30…100 °C (–22…212 °F) with no icing or condensation
Ambient Humidity
45…85% (no condensation)
Standards Compliance
UL 508, CSA C22.2 No. 14, EN 60947-1, -4-3
Certifications
cURus Recognized (File No. E96956, Guide NMFT2/NMFT8), CE Marked, VDE Certified
Weight
Approx. 70 g
1 With constant current input system. SSR input impedance varies with a change in input (control) voltage.
Refer to the following graph “Load Current Vs. Ambient Temperature Characteristics” for additional load current details.
‡ If the SSR operation is continuous ON/OFF, this value should be reduced by 50%. Refer to “Inrush Current Resistivity” graph below.
§ 60 Hz full cycle time = 16.6 ms, 50 Hz full cycle time = 20 ms.
Load Current vs. Ambient Temperature Characteristics
Inrush Current ResistivityΔ
700-SA
700-SA
80
2
1
40
700-SAZY5Z25
30
20
10
Ambient Temperature [° C]
500
100
700-SANY3Z25
200
0
30
50
100
80
60
40
20
0
0
-30
-20
50
5000
700-SANY3Z25
3
10
Load Current [A]
4
70
60
1000
Inrush Current [A. Peak]
700-SAZY5Z25
5
Energizing Time [ms]
Δ Inrush current resistivity is the ability of an SSR to withstand a large surge current for a short period of time. Surges are considered non-repetitive (max.
repeatability once every 5 seconds). Keep the inrush current to half the rated value if it occurs repetitively. Exceeding the non-repetitive inrush current will
damage the SSR.
Rockwell Automation Publication 700-TD552A-EN-P
109
700-SA Solid State Relays
Relays and Timer Specifications
Terminal Arrangement (Bottom View)
Load
Load
power
supply
Load
Input
Input voltage
Note: The plus and minus symbols shown in parentheses
are for DC loads.
Basic Application Considerations
High Density Mounting of Multiple SSRs
If multiple SSRs are installed side-by-side be aware that the outer case wall of the SSR serves to dissipate heat. Install the relays so that they
are adequately ventilated. If poor ventilation is unavoidable, reduce the load current to half.
Protective Component
When controlling AC inductive loads, connect an inrush/surge absorbing device (varistor) across the SSR load terminals. If the SSR has builtin surge suppression (Bulletins 700-SE and 700-SH) and additional surge suppression is required, connect the varistor across the terminals of
the load device. Select a varistor that meets the conditions of the load voltage outlined in the table below.
Load Voltage
Varistor Voltage [V]
100…120V AC
240…270
200…240V AC
440…470
380…480V AC
820…1000
Varistor Surge Resistance
1000 A min.
Note: For additional details applying solid-state relays, refer to pub. 700-AT001*, Solid-State Relay Application Guide.
For a DC inductive load, a diode should be connected parallel to the load to absorb the counter electromotive force (OFF) of the load.
EMC Directive Compliance
1. AC-switching models comply with EMC Directives
under the following conditions:
Load
Load power
supply
SSR
Input
3 m max.
Load
Input
700-SA
Varistor: 470 V, 0.6 W
Film Capacitor: 1μ F, 250 VAC
Output
Varistor
Film Capacitor
• Connect a varistor between the output terminals.
• Connect a film capacitor to the load power supply.
• The input cable must be less than 3 m.
2. DC-switching models comply with EMC Directives
under the following conditions:
Less than 10 m
Load
Input
700-SA Output
• The input cable must be less than 10 m.
Approximate Dimensions
All units in millimeters unless otherwise indicated. To convert millimeters to inches multiply by 0.0394. Dimensions are not intended to be
used for manufacturing purposes.
Bul. 700-SA
+
35
max.
+
35
max.
52.5
max.
Bulletin 700-SA is compatible with Cat. Nos. 700-HN100, -108, -125, and -204 (sockets).
110
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SC Solid State Relays
Control/Input Ratings
Cat. No.
Rated Control
Voltage
Max. Operating
Control Voltage
Range
Max. Reverse
Control Voltage [V]
Control Voltage Levels
Impedance
Pick-up Voltage
700-SCZY3Z25
5…24V DC
4…28V DC
-28.8
15 mA max. 4V DC max.
1V DC min.
700-SCZY2A1
100/110V AC
75…125V AC
NA
41 kΩ± 20%
75V AC max.
20V AC min.
40V AC min.
700-SCZY2A2
200/220V AC
150…250V AC
NA
72 kΩ± 20%
150V AC max.
700-SCTY3Z24
24V DC
19.2…28.8V DC
-28.8
2 kΩ± 20%
19.2V DC max.
700-SCNY3Z25
5…24V DC
4…28V DC
-28
1.5 kΩ +20%/ -10% ‡
4V DC max.
700-SCZN3Z26
4…24V DC
3…28V DC
-28.8
15 mA max. 3V DC max.
700-SCTN3Z24
24V DC
19.2…28.8V DC
-28.8
2 kΩ± 20%
19.2V DC max.
700-SCNN3Z26
4…24V DC
700-SCNN2Z25
5…24V DC
1.5 kΩ +20%/ -10% ‡
3V DC max.
-28
3…28V DC
-28.8
Drop-out Voltage
1V DC min.
Load/Output Ratings
Cat. No.
Rated Control
Voltage
Max. Load
Voltage Range
100…240V AC
75…264V AC
Continuous Load Current
(Resistive) [A]
Min.
Max.♣
0.1
3
Max. Inrush Current§
700-SCZY3Z25
700-SCTY3Z24
700-SCZN3Z26
700-SCTN3Z24
45 A (@50/60 Hz, 1
cycle)
700-SCZY2A1
700-SCZY2A2
700-SCNN3Z26
2
4…48V DC
3…52.8V DC
0.1
3
18 A (10 ms)
5…110V DC
3…125V DC
0.1
2
10 A (10 ms)
700-SCNY3Z25
700-SCNN2Z25
0.1
With constant current input circuit system. SSR impedance varies with a change in input (control) voltage.
‡ Input impedance attains its maximum at the operating voltage.
§ If the SSR operation is continuous ON/OFF, this value should be reduced by 50%. Refer to “Inrush Current Resistivity” graphs on page 9-177 for details.
♣ Refer to the following “Load Current Versus Ambient Temperature Characteristics” graphs on page page 9-177 for additional load current details.
Characteristics
Description
Cat. No. 700-SCZ…
Load Switching Method/Device
Pick-up time
Drop-out time
Cat. No. 700-SCT
Cat. Nos. 700-SCNY, 700SCNN3…
Triac
1/2 of load power source cycle
time Δ+ 1 ms max. (DC input)
3/2 of load power source cycle
time Δ+ 1 ms max. (AC input)
Cat. Nos. 700-SCNN2…
Transistor
1 ms max
1/2 of load power source cycle
timeΔ + 1 ms max. (DC input) 1/2 of load power source cycle
timeΔ + 1 ms max
3/2 of load power source cycle
timeΔ + 1 ms max. (AC input)
0.5 ms max.
0.5 ms max.
2 ms max.
2.5 ms max.
Output On Voltage Drop
1.6 V (RMS) max.
1.6 V (RMS)
1.5 V max.
1.5 V max.
Output Leakage Current
5 mA max (@ 100 V AC)
10 mA max (@ 200 V AC)
2.5 mA max (@ 100 V AC) 5
mA max (at 200 V AC)
5 mA max (@ 50 V DC)
0.1 mA max (@ 100 V DC)
Output VDRM, VCEO (V)
600
600
80
80
Output di/dt (A/uS)
50
50
—
—
Output dv/dt (V/uS)
250
250
—
—
Output I2t (A2S)
18
18
—
—
Output Tj (°C) Max.
125
125
150
150
Insulation Resistance
100 MΩ min (@500V DC)
Dielectric Strength
1500V AC, 50/60 Hz for 1 minute
Vibration Resistance (max.)
10…55 Hz, 1.5 mm double amplitude (10 G)
Shock Resistance (max.)
1000 m/s2 (100 G)
Ambient Temperature
Operating: -30…+80 °C (-22...+176 °F) with no icing or condensation
Storage: -30…+100 °C (-22...+212 °F) with no icing or condensation
Standards Compliance
UL5 08, CSA C22.2 No. 14, EN/IEC 60950, EN 50011, EN 61000-6-2, EN/IEC 60947-1, -4-3
Certifications
cURus Recognized (File No. E96956, Guide NMFT2/NMFT8), CE Marked, VDE Certified
Ambient Humidity
Operating: 45…85% (no condensation)
Weight
Approx. 50 g
Δ 60 Hz full cycle time = 16.6 ms, 50 Hz full cycle time = 20 ms
Rockwell Automation Publication 700-TD552A-EN-P
111
700-SC Solid State Relays
Relays and Timer Specifications
Load Current Versus Ambient Temperature Characteristics
700-SC_ _2...
5
4
4
Ambient Temperature [° C]
Inrush Current Resistivity
700-SCNN3...
700-SCZ....
700-SCT...
100
80
700-SCNN2...
Energizing Time [ms]
10
8
6
4
5000
3000
1000
300
500
100
0
20
30
50
2
10
2000
Inrush Current [A. Peak]
Energizing Time [ms]
1000
5000
500
1000
200
10
0
100
10
700-SCNY3
200
300
500
20
20
30
50
70
100
30
Ambient Temperature [° C]
12
10
Inrush Current [A. Peak]
40
30
50
Inrush Current [A. Peak]
50
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
60
60
20
100
0
80
0
40
1
0
1
40
2
20
2
3
0
3
-30
-20
Load Current [A]
5
-30
-20
Load Current [A]
700-SC_ _3...
Energizing Time [ms]
Inrush current resistivity is the ability of an SSR to withstand a large surge current for a short period of time. Surges are considered non-repetitive (max.
repeatability once every 2…5 seconds). Keep the inrush current to half the rated value if it occurs repetitively. Exceeding the non-repetitive inrush current will
damage the SSR.
EMC Directive Compliance
1. AC-switching models comply with EMC Directives under the
following conditions
3 m max.
Load
Input
700-SC
Varistor: 470 V, 0.6 W
Film capacitor: 1μ F, 250 VAC
Output
Varistor
Film capacitor
• Connect a varistor between the output terminals.
• Connect a film capacitor to the load power supply.
• The input cable must be less than 3 m.
2. DC-switching models comply with EMC Directives under the
following conditions
Less than 10 m
Load
Input
700-SC
Output
• The input cable must be less than 10 m.
112
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SC Solid State Relays
Approximate Dimensions
All units in millimeters unless otherwise indicated. To convert to inches multiply by 0.0394. Dimensions are not intended for manufacturing
purposes.
Terminal Arrangement/
Internal Connections
(Bottom View)
28 max.
1
4
5
8(+)
9
Load
Load
(+)
12(–)
(–)
21.5 max.
13
36.5 max.
Input
14
–
42.5 max.
–
Note:
Load
power
supply
+
Input voltage
+
The plus and minus symbols shown
in parentheses are for DC loads.
Cat. No 700-SC…
Bulletin 700-SC is compatible with Cat. Nos. 700-HN103, -HN104, and -HN128 socket.
Rockwell Automation Publication 700-TD552A-EN-P
113
700-SC Solid State Relays
Relays and Timer Specifications
Basic Application Considerations For Bulletin 700-SC
Connection
For DC Load Switching, Bulletin 700-SC will operate properly if the load is connected to either the positive or negative SSR load terminal.
High-Density Mounting of Multiple SSRs
If multiple relays are mounted side-by-side, be aware that the outer wall of each SSR works as a radiator.
The SSR casing serves to dissipate heat. Install the relays so that they are adequately ventilated. If poor ventilation is unavoidable, reduce the
load current by half.
Protective Component
When controlling AC inductive loads, connect an inrush/surge absorbing device (varistor) across the SSR load terminals. If the SSR has builtin surge suppression (Bulletins 700-SE and 700-SH) and additional surge suppression is required, connect the varistor across the terminals of
the load device. Select a varistor that meets the conditions of the load voltage outlined in the table below.
Load Voltage [V AC]
Varistor Voltage [V]
100…120
240…270
200…240
440…470
380…480
820…1000
Varistor Surge Resistance
1000 A min.
For a DC inductive load, a diode should be connected parallel to the load to absorb the counter electromotive force (OFF) of the load.
Load
Input
SSR
Load power
supply
Note: For additional details when using Solid-State Relays, refer to pub. 700-AT001*, Solid-State Relay Application Guide.
114
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SF Solid State Relays
Specifications
Control/Input Ratings
Cat. No.
Rated Control
Voltage
Max. Operating
Control Voltage
Range [V DC]
Max. Reverse
Control Voltage [V]
Impedance
Pick-up Voltage
700-SFZY3Z25
5…24V DC
4…28V DC
–32
15 mA max.
4V DC max.
1V DC min.
700-SFTY3Z24
24V DC
19.2…28.8V DC
–28.8
2 kΩ ± 20%
19.2V DC max.
1V DC min.
700-SFNY3Z25
5…24V DC
4…28V DC
–28.8
1.5 kΩ + 20%/–10%‡
4V DC max.
1V DC min.
Control Voltage Levels
Drop-out Voltage
Load/Output Ratings
Cat. No.
Rated Load Voltage
700-SFZY3Z25
700-SFTY3Z24
700-SFNY3Z25
Max. Load Voltage
Range
100…240V AC
75…264V AC
4…48V DC
3…52.8V DC
Continuous Load Current (Resistive) [A]
Min.
Max.♣
0.1
3
0.1
3
0.1
3
Max. Inrush Current§
45 A @ 50/60 Hz, 1 cycle
18 A (10 ms)
Characteristics
Description
Load Switching Method/Device
Pick-up Time
Drop-out Time
Cat. No. 700-SFZY3Z25
Cat. No. 700-SFTY3Z24
Triac
Cat. No. 700-SFNY3Z25
Transistor
1/2 cycle of load power source cycle
time Δ + 1 ms max.
1 ms max.
0.5 ms max.
2 ms max.
1/2 cycle of load power source cycle timeΔ + 1 ms max.
Output ON Voltage Drop
1.6V (RMS) max.
1.5V max.
5 mA max. (@ 100 V AC);
10 mA max. (@ 200 V AC)
2.5 mA max. (@ 100V AC);
5 mA max. (@ 200V AC)
5 mA max. (@ 50V DC)
Output VDRM, VCEO (V)
600
600
80
Output di/dt (A/uS)
50
50
—
Output dv/dt (V/uS)
250
250
—
Output I2t (A2S)
18
18
—
Output Tj (°C) Max.
125
125
150
Output Leakage Current
Insulation Resistance
Dielectric Strength
Vibration Resistance (Max.)
Shock Resistance (Max.)
Ambient Temperature
Ambient Humidity
Standards Compliance
Certifications
Weight
100 MΩ min. (at 500V DC)
1,500V AC, 50/60 Hz for 1 min
10…55 Hz, 1.5 mm double amplitude (10 G)
1000 m/s2 (100 G)
Operating: –30…+80 °C (–22…+176 °F) with no icing or condensation
Storage: –30…+100 °C (–22…=212 °F) with no icing or condensation
45…85% (no condensation)
UL 508, CSA C22.2 No. 14, EN/IEC 60947-1, -4-3, EN/IEC 60950
cURus Recognized (File No. E96956, Guide NMFT2/NMFT8), CE Marked, VDE Certified
Approx. 50 g
With constant curent input circuit system, SSR impedance varies with a change in input voltage.
‡ Input impedance reaches its maximum at the operating voltage.
§ If the SSR operation is continuous ON/OFF, this value should be reduced by 50%. Refer to the “Inrush Current Resistivity” graphs on page 9-181 for more
details.
♣ Refer to “Load Current vs. Ambient Temperature Characteristics” on page 9-181 for additional load current details.
Δ 60 Hz full cycle time = 16.6 ms, 50 Hz full cycle time 20 ms.
Rockwell Automation Publication 700-TD552A-EN-P
115
700-SF Solid State Relays
Relays and Timer Specifications
Note: This data is non-repetitive. Keep the inrush current to half the rated value if it occurs repetitively. Inrush current resistivity is the ability of an SSR to
withstand a large surge current for a short period of time. Surges are considered non-repetitive (max. repeatability once every 2…5 seconds). Keep the
inrush current to half the rated value if it occurs repetitively. Exceeding the non-repetitive inrush current will damage the SSR.
Inrush Current
Resistivity
700-SFZ… 700SFT…
2000
500
Energizing Time [ms]
Energizing Time [ms]
Ambient Temperature [° C]
1000
5000
100
80
60
40
20
-20
-30
0
10
30
50
0
0
500
10
200
300
Inrush Current [A]
20
1000
1
30
200
2
40
100
3
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
50
70
100
50
Inrush Current [A Peak]
Load Current [A]
4
Inrush Current Resistivity
700-SFN…
20
30
700-SF…
10
Load Current vs. Ambient
Temperature Characteristics
Inrush current resistivity is defined as the ability of an SSR to withstand a large surge current for a short period of time. Surges are considered non-repetitive
(max. repeatability once every 2…5 seconds). Keep the inrush current to half the rated value if it occurs repetitively. Exceeding the non-repetitive inrush current
will damage the SSR.
EMC Directive Compliance
1. AC-switching models comply with EMC Directives under the
following conditions
3 m max.
Load
Input
700-SF
Varistor: 470 V, 0.6 W
Film capacitor: 1μ F, 250 VAC
Output
Varistor
Film capacitor
• Connect a varistor between the output terminals.
• Connect a film capacitor to the load power supply.
• The input cable must be less than 3 m.
2. DC-switching models comply with EMC Directives under the
following conditions
Less than 10 m
Load
Input
700-SF
Output
• The input cable must be less than 10 m.
116
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SF Solid State Relays
Approximate Dimensions
All units are in millimeters unless otherwise indicated. To convert to inches multiply by 0.0394. Dimensions are not intended for manufacturing
purposes.
Terminal Arrangement/Input Connections
(Bottom View)
28
max
1
2
3
4(+)
5
Load
Load
(+)
6(-)
(-)
7
21.5
max
36.5 max
42.5 max
Input
-
-
8
+
Input Voltage
+
Notes: 1. The plus and minus symbols
shown in parentheses are
for DC loads.
2. The coil has no polarity.
Note: Bul. 700-SF is compatible with Cat. No. 700-HN116 socket.
Rockwell Automation Publication 700-TD552A-EN-P
117
700-SF Solid State Relays
Relays and Timer Specifications
Basic Application Considerations of Bulletin 700-SF
High Density Mounting of Multiple SSRs
If multiple SSRs are mounted side-by-side, be aware that the outer case wall of the SSR acts as a radiator. The SSR case serves to dissipate
heat. Install the relays so that they are adequately ventilated. If poor ventilation is unavoidable, reduce the load current by half.
Connection
For DC load switching, the Bul. 700-SF SSR will operate properly if the load is connected to either the positive or negative load terminals.
Protective Component To Extend SSR Life
When controlling AC inductive loads, connect an inrush/surge absorbing device (varistor) across the SSR load terminals. If the SSR has builtin surge suppression (Bulletins 700-SE and 700-SH) and additional surge suppression is required, connect the varistor across the terminals of
the load device. Select a varistor that meets the conditions of the load voltage outlined in the table below.
Load Voltage [V AC]
Varistor Voltage [V]
100…120
240…270
200…240
440…470
380…480
820…1000
Varistor Surge Resistance
1000 A min.
For a DC inductive load, a diode should be connected parallel to the load to absorb the counter electromotive force (OFF) of the load.
Load
Input
SSR
Load power
supply
Note: For additional details when using Solid-State Relays, refer to pub. 700-AT001*, Solid-State Relay Application Guide.
118
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SH Solid State Relays
Control/Input Ratings
Cat. No.
700-SH10J…
700-SH_ _ H…
700-SH_ _ G…
Operating Voltage
Input Current @ Max.
Voltage
Voltage Level Pickup Voltage
3…32V DC
12 mA
2.75V DC max.
1.2V DC min.
80…130V AC
13 mA
70V AC max.
30V AC min.
200...280V AC
13 mA
190V AC max.
90V AC min.
4…32V DC
12 mA
4V DC max.
1V DC min.
20…280V AC/22…48V DC
20 mA
18V AC/DC
6V AC/DC
3…32V DC
12 mA
2.5V DC
1.2V DC
20…280V AC/22…48V DC
20 mA
-32V DC
6V AC/DC
Drop-Out Voltage
4…32V DC
12 mA
3.5V DC
1.2V DC
20…280V AC/22…48V DC
20 mA
18V AC/DC
6V AC/DC
700-SH_ _ W…
Current Control
4…20 mA
—
—
700-SH_ _ F…
3…32V DC
12 mA
3V DC max.
1.0V DC
700-SH_ _ V…
When specified heatsink is used.
Output Ratings
Cat. No.
Load Voltage Range
Applicable Load Current with Heat Sink [A]‡
700-SH5FZ24
3…60V DC
0.001…5 A DC
700-SH10J…
42…265V AC
0.15…10
700-SH10H…
42…530V AC
0.15…10
700-SH25G…
24…265V AC
0.15…25
700-SH25H…
42…530V AC
0.15…25
0.15…25
700-SH25V…
42…660V AC
700-SH25W…
90…280V AC
0.15…25
700-SH50G…
24…265V AC
0.15…50
700-SH50H…
42…530V AC
0.15…50
700-SH50V…
42…660V AC
0.15…50
700-SH50W…
90…280V AC
0.15…50
700-SH75H…
42…530V AC
0.15…75
700-SH75V…
42…660V AC
0.15…75
700-SH100H…
42…530V AC
0.15…100
700-SH100V…
42…660V AC
0.15…100
Cat. Nos. 700-SH10, 25, 50 (not including 700-SH_
_W)
Cat. Nos. 700-SH75, 100
‡ AC unless indicated.
Characteristics
Description
Pick-up Time
1/2 of load power source cycle time(DC input)
1 of load power source cycle time (AC input)
Drop-out Time
1/2 of load power source cycle time (DC input)
2 of load power source cycle time (AC input)
Output ON Voltage Drop
1.6V (RMS) max.
Output Leakage Current
<3 mArms
100 MΩ min (@ 500V DC)
Insulation Resistance
100 MΩ min. (at 500V DC)
Dielectric Strength
Vibration Resistance
>4000 VACrms
Malfunction: 10…55 Hz, 1.5 mm double amplitude
Malfunction: 1000 m/s2
Shock Resistance
Ambient Temperature
Operating: –20…+70 °C with no icing or condensation
Storage: –40…+100 °C with no icing or condensation
Ambient Humidity
Standards Compliance
Certifications
Weight
0…95% no condensing
UL 508, CSA C22.2 No. 14, EN/IEC 60947-1, -4-2, -4-3, EN 61000-6-2, EN 61000-6-4
cURus Recognized (File No. E14843, Guide NPNT2), CSA Certified (File No. 240924)
Approx. 60 g
Rockwell Automation Publication 700-TD552A-EN-P
Approx. 100 g
119
700-SH Solid State Relays
Relays and Timer Specifications
Characteristics
Description
Cat. No. 700-SH_ _W
Pick-up Current
4.2 mA
Drop-out Current
4.1 mA
Voltage Drop
<10V DC @ 20 mA
Leakage Current
<3 mA
Insulation Voltage
<4000 Vrms
Vibration Resistance
Malfunction: 10…55 Hz, 1.5 mm double amplitude
Shock Resistance
Malfunction: 1000 m/s2
Ambient Temperature
Operating: –20…+70 °C with no icing or condensation
Ambient Humidity
0…95% no condensing
Standards Compliance
UL 508, CSA C22.2 No. 14, EN/IEC 60947-1, -4-2, -4-3, EN 61000-6-2,
EN 61000-6-4
Certifications
cURus Recognized (File No. E14843, Guide NPNT2), CSA Certified
(File No. 24024)
Weight
Approx. 60 g
Description
Cat. No. 700-SH5FZ24
Pick-up Voltage
<3V DC
Drop-out Voltage
>1V DC
Activating Frequency
<100 Hz
Input Impedance
1kΩ
Response Time Pick-up @ Vin > 5V
<4000 uS
Response Time Drop-out
<1 mS
On-state Voltage Drop @ Rated Current
<1.5V
Off-state Current Drop @ Rated Voltage
<1 mA
Insulation Voltage
<1 mA
Vibration Resistance
Malfunction: 10…55 Hz, 1.5 mm double amplitude
Shock Resistance
Malfunction: 1,000 m/s2
Ambient Temperature
Operating: –20…+70 °C with no icing or condensation
Ambient Humidity
0…95% no condensing
Standards Compliance
UL 508, CSA C22.2 No. 14, EN/IEC 60947-1, -4-2, -4-3, EN 61000-6-2,
EN61000-6-4
Certifications
cURus Recognized (File No. E14843, Guide NPNT2), CSA Certified (File No.
240924)
Weight
Approx. 60 g
Surge Current vs. Ambient Temperature Characterstics
Surge current resistivity for 700-SH50....
700A
300A
600A
250A
500A
Inrush current (Apk)
Inrush current (Apk)
Surge current resistivity for 700-SH10, 25....
350A
200A
150A
400A
300A
100A
200A
50A
100A
0A
10ms
100ms
1000ms
10000m s
0A
10ms
Energizing time (ms)
120
100ms
1000ms
Energizing time (ms)
Rockwell Automation Publication 700-TD552A-EN-P
10000m s
Relays and Timer Specifications
700-SH Solid State Relays
Surge current resistivity for 700-SH75....
1200A
Surge current resistivity for 700SH100....
2000A
1800A
1000A
1600A
Inrush current (Apk)
1400A
600A
400A
1200A
1000A
800A
600A
200A
400A
200A
0A
10ms
100ms
1000ms
10000m s
0A
10ms
Energizing time (ms)
100ms
1000ms
10000m s
Energizing time (ms)
Load current vs. ambient temperature characteristics for 700-SH10….
Load current vs. ambient temperature characteristics for 700-SH25….
12
30
700-SN50VHC
10
700-SN50HC
700-SN10
700-SN50(V)HC
25
700-SN25
700-SN10
6
4
No heatsink
15
No heatsink
5
0
-10
0
10
20
700-SN50
10
2
-20
700-SN25
20
700-SN50
Load Current (A)
Load Current (A)
8
30
40
50
60
70
0
80
-20
Ambient temperature (ºC)
-10
0
10
20
30
40
50
60
70
80
Ambient temperature (ºC)
Load current vs. ambient temperature characteristics for 700-SH75….
Load current vs. ambient temperature characteristics for 700-SH5…..
80
6
700-SN50(V) HC
700-SN50VHC
70
5
700-SN50HC
60
700-SN10
700-SN25
700-SN50
50
700SN10
40
700-SN25
Load Current (A)
Load Current (A)
4
700-SN50
30
No heatsink
3
2
20
1
10
No heatsink
0
0
-20
-10
0
10
20
30
40
50
60
70
80
-20
-10
0
10
20
Ambient temperature (ºC)
30
40
50
60
70
80
Ambient temperature (ºC)
Load current vs. ambient temperature characteristics for 700-SH50….
60
Load current vs. ambient temperature characteristics for 700-SH100….
120
50
700-SN50VHC
100
700-SN50HC
700-SN50VHC
Load Current (A)
700-SN50
40
80
Load Current (A)
Inrush current (Apk)
800A
60
700-SN10
700-SN10
700-SN25
700-SN50
700-SN50HC
30
700-SN25
20
40
20
10
No heatsink
No heatsink
0
-20
-10
0
10
20
30
40
Ambient temperature (ºC)
50
60
70
80
0
-20
-10
0
10
20
30
40
50
60
70
80
Ambient temperature (ºC)
Rockwell Automation Publication 700-TD552A-EN-P
121
700-SH Solid State Relays
Relays and Timer Specifications
Mounting Considerations§♣Δ
All units are in mm's unless otherwise indicated. To convert to inches multiply by 0.0394. Dimensions are not intended for manufacturing purposes.
24.5
30.0
45.5
Mounting Holes
(Bottom View)
5.3
2 x M5
Screws
Load
Two Ø 4.4
or M4 Holes
47.5
47.5
58.2
Terminal Arrangement/
Internal Connections
(Top View)
Load
L1
A2
2 x M3
Screws
Input
Load
Power
Supply
T1
A1
13.0
25
45.5
Cat. No. 700-SH5F…
44.8
28.8
Two Ø 4.4
or M4 Holes
47.5
12.3
2 X M5
Screws
8.6
47.5
58.2
Operating
Indicator
APPLY
HEATSINK
COMPOUND
2 X M3
Screws
5.2
5.25
25
45.5
Cat. No. 700-SH10, -SH25, -SH50, -SH75, -SH100
The proper mounting orientation of the heat sink is so the heat fins run perpendicular to the floor (vertical) to maximize ventilation flow. If the fins do not run
perpendicular to the floor, a 30% current derating is required.
§ When attaching a heat sink to Bulletin 700-SH, apply a thin layer of heat conductive grease (approximately 0.002 in. thick) on the heat sink to maximize heat
transfer between the SSR and the heat sink. Recommended types: Silicon based, Dow Corning 340, Toshiba YG6240; Non-silicon based, AOS company type
53300 (Cat. No. 46801-010-01).
♣ Tighten the SSR panel/heat sink mounting screws to a torque of 0.78…0.98 N•m (6.9…8.7 lb•in).
Δ Tighten the SSR terminal wiring screws as follows M4: 0.98…1.37 N•m (8.67…12.12 lb•in), M5: 1.57…2.35 N•m (13.89…20.8 lb•in).
122
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SH Solid State Relays
700-SN10
700-SN25
700-SN50
700-SN50HC
700-SN50VHC
♦ Tighten the heat sink mounting screws (M4) to a torque of 0.98…1.37 N•m (8.67…12.12 lb•in).
♠ Heat sink weight: Cat. Nos. 700-S10 = 200 g, 700-S20 = 400 g, 700-S30 = 560 g.
Rockwell Automation Publication 700-TD552A-EN-P
123
700-SH Solid State Relays
Relays and Timer Specifications
12
47
27
45
67
27,5
Cat. No. 700-SHCOV
Cat. No.700-SHTRMA
28,5
Load Connection
For an AC load, use a power supply rated at 50 or 60 Hz. The maximum operating frequency is 10 Hz.
The Bulletin 700-SH has a built-in varistor for surge/inrush protection of AC loads. If additional suppression is required, connect an external
varistor across the load device terminals. Select a varistor which meets the load voltage condition outlined in the table below.
Load Voltage [V AC]
Varistor Voltage [V]
100…120
240…270
200…240
440…470
380…480
820…1000
Varistor Surge Resistance
1000 A min.
Zero Cross Function
A SSR with a zero cross function operates when an AC load voltage reaches the zero point or its vicinity. This reduces clicking noises when
the load is switched and minimizes the influence of an inductive load, (e.g., lamp, heater, or motor) on the power supply because the inrush
current of the load is reduced. This can also minimize the scale of the inrush current protection circuit.
Output (load voltage)
Input
ON
OFF
At a low applied voltage (e.g., 24V AC) the load current is not fully supplied. When the unit is switched ON, the voltage required to power the
unit deprives the output signal of the necessary voltage level and thus creates loss time. The lower the load voltage is, the greater the loss
time is. This condition, however, will not create any serious problems.
Loss time
For a DC inductive load, a diode should be connected parallel to the load to absorb the counter electromotive force (OFF) of the load.
Load
Input
SSR
Load power
supply
Note: For additional details when using Solid-State Relays, refer to pub. 700-AT001*, Solid-State Relay Application Guide.
124
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SK Solid State Relays
Input Sensor Module
Input Sensor Ratings
Cat. No.
Rated Input Voltage
Max. Operating Input
Voltage Range
Input Current
Pick-up Voltage
Drop-out Voltage
700-SKICZ24
12…24V DC
6.6…32V DC
8 mA max.
6.6V DC max.
3.6V DC min.
700-SKICA18
100…240V AC
60…264V AC
15 mA max.
60V AC max.
20V AC min.
Output Logic Ratings
Cat. No.
Logic Level Supply Voltage
Logic Level Supply Current Draw
4…32V DC
0.1…100 mA
Cat. No. 700-SKICA18
Cat. No. 700-SKICZ24
700-SKICZ24
700-SKICA18
Characteristics
Description
Pick-up time
20 ms max.
0.1 ms max.
Drop-out time
20 ms max.
0.1 ms max.
Response frequency
10 Hz
1 kHz
Output ON voltage drop
1.6V max.
5 μA max.
Leakage current
Output VDRM, VCEO (V)
80 (ref. value)
80 (ref. value)
Output di/dt (A/uS)
—
—
Output dv/dt (V/uS)
—
—
Output I2t (A2S)
Output Tj (°C) Max.
—
—
150
150
Insulation Resistance
100 MΩ min. between input and output
Dielectric Strength
4000V AC, 50/60 Hz for 1 min between input and output
Vibration Resistance (Max.)
10…55 Hz, 1.5 mm double amplitude (10 G)
1000 m/s2 (100 G)
Shock Resistance (Max.)
Ambient Temperature
Operating
–30…+80 °C (–22…+176 °F) with no icing or condensation
Storage
–30…+100 °C (–22…+212 °F) with no icing or condensation
Standards Compliance
UL 508, CSA C22.2 No. 14, EN/IEC 60950
Certifications
cURus Recognized (File No. E96956, Guide NMFT2/NMFT8), CE Marked, TÜV Certified
Ambient humidity
Operating
45…85% (no condensation)
Weight
Approx. 18 g
Output SSR Module
Control/Input Ratings
Cat. No.
Rated Control Voltage
Max. Operating Control
Voltage Range
Max. Reverse
Control Voltage
Impedance
-32V DC
15 mA max.
at 25 °C
(77 °F)
700-SKOZ2Z25
700-SKON2Z25
5…24V DC
4…32V DC
700-SKOC2Z25
Pick-up
Voltage
Drop-out
Voltage
4V DC
max.
1V DC min.
8 mA max.
700-SKOC1Z25
Load/Output Ratings
Cat. No.
700-SKOZ2Z25
700-SKON2Z25
Rated Load
Voltage
Maximum
Load Voltage Range
100…240V AC
75…264V AC
Continuous Load Current
(Resistive) [A]
Min.
Max.§
Max. Inrush Current‡
0.05
2
30 A (@50/60 Hz, 1
cycle)
700-SKOC2Z25
5…48V DC
4…60V DC
0.1
2
8 A (10 ms)
700-SKOC1Z25
48…200V DC
40…200V DC
0.1
1.5
8 A (10 ms)
With a constant current input system. SSR impedance varies with a change in input voltage.
‡ If the SSR operation is continuous ON/OFF, this value should be reduced by 50%. Refer to the “Inrush Current Resistivity” graphs on page 9-193 for more
details.
§ Refer to "Load Current vs. Ambient Temperature Characteristics" graphs on page 9-193 for additional details.
Rockwell Automation Publication 700-TD552A-EN-P
125
700-SK Solid State Relays
Relays and Timer Specifications
Output Module, Continued
Characteristics
Description
Cat. No. 700-SKOZ2Z25
Load Switching Method/Device
Cat. No. 700-SKON2Z25
Cat. No. 700-SKOC2Z25
Cat. No. 700-SKOC1Z25
Triac
Transistor
Pick-up Time
1/2 cycle of load power source cycle time + 1 ms
max.
1 ms max.
Drop-out Time
1/2 of load power source cycle time + 1 ms max.
2 ms max.
20 Hz
100 kHz
Response Frequency
Output ON Voltage Drop
1.6V max.
Leakage Current
2.5V max.
1.5 mA max.
Output VDRM, VCEO (V)
1 mA max.
600 (ref.value)
600 (ref.value)
80 (ref.value)
400 (ref.value)
Output di/dt (A/uS)
30
30
—
—
Output dv/dt (V/uS)
300
300
—
—
Output I2t (A2S)
10.4
10.4
—
—
Output Tj (°C) Max.
125
125
150
150
Insulation Resistance
100 MΩ min. between input and output
Dielectric Strength
4000V AC, 50/60 Hz for 1 min between input and output
Vibration Resistance (Max.)
10…55 Hz, 1.5 mm double amplitude (10 G)
1000 m/s2 (100 G)
Shock Resistance (Max.)
Ambient Temperature
Operating
–30…+80 °C (–22…+176 °F) with no icing or condensation
Storage
–30…+100 °C (–22…+212 °F) with no icing or condensation
Standards Compliance
UL 508, CSA C22.2 No. 14, EN/IEC 60950
Certifications
cURus Recognized (File No. E96956, Guide NMFT2/NMFT8), CE Marked, TÜV Certified
Ambient Humidity
Operating
45…85% (no condensation)
Weight
Approx. 18 g
60 Hz cycle time = 16.6 ms, 50 Hz cycle time = 20 ms.
Load Current vs. Ambient Temperature Characteristics
10
9
9
8
8
3
2
100
5
4
3
2
Energizing Time (ms)
10
2000
1000
0
300
500
1
0
100
1
2000
4
6
1000
5
7
300
500
6
700-SKOZ/SKOC1
100
Inrush Current (A)
7
10
Inrush Current (A)
Energizing Time (ms)
5000
1000
500
100
200
30
50
10
Inrush Current (A)
30
700-SKOC2
30
50
10
30
50
Inrush Current Resistivity‡
700-SKOZ/SKON
10
80
Ambient Temperature [° C]
Ambient Temperature [° C]
20
60
-20
0.5
100
80
60
40
20
0
0.5
1
40
1
1.5
20
1.5
2
0
Maximum Load Current (A)
2
-20
Maximum Load Current (A)
For 2 A Versions
Energizing Time (ms)
‡ Inrush current resistivity is the ability of an SSR to withstand a large surge current for a short period of time. Surges are considered non-repetitive (max.
repeatability once every 2…5 seconds). Keep the inrush current to half the rated value if it occurs repetitively. Exceeding the non-repetitive inrush current will
damage the SSR.
126
Rockwell Automation Publication 700-TD552A-EN-P
Relays and Timer Specifications
700-SK Solid State Relays
All units are in millimeters unless otherwise indicated. To convert to inches multiply by 0.0394. Dimensions are not to be used for
manufacturing purposes.
Note: The input module ( Bul. 700-SKI) and output module (Bul. 700-SKO) are compatible with the Cat. No. 700-HN121 socket.
1
5.2
Terminal Arrangement/
Internal Connections
(Bottom View)
3
0.5
29 max.
17.4
4.75
1
13 max.
28 max.
5
(+)
4
9.6
(–)
4.7
Input
0.5 4.75
4
4
Load
5
7.5
3
10
1
5
(–)
(+)
2
20
Application Considerations of Bulletin 700-SK
Connection
For DC load switching, Bulletin 700-SK SSR will operate properly if the load is connected to either the positive or negative SSR load terminal.
The load can be connected to either positive or negative output terminals of the SSR.
Protective Element (to extend SSR life)
Since the SSR does not incorporate a surge absorption component, be sure to connect a surge absorption component when using the SSR
to control an inductive load.
For additional details applying solid-state relays, refer to pub. 700-AT001A*, Solid-State Relay Application Guide.
Rockwell Automation Publication 700-TD552A-EN-P
127
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required
to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be
impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the
use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this
document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/.
Allen-Bradley, Rockwell Software, Rockwell Automation, and LISTEN. THINK. SOLVE are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Publication 700-TD552A-EN-P - September 2014
Copyright © 2014 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement