KitchenAid KUIS185 User manual

KitchenAid KUIS185 User manual
Installation Instructions
KitchenAid”
FOR THE WAY IT'S МАРЕ:
Ice Maker Safety .................. 2
Before you plug it in .......... 2
General Information ............ 3
Unpack.....................ene...—. 3
Utilities required ................ 3
Thermostat calibrations..... 4
Shipboard operation .......... 4
Installation 5
Locate unit 5
Level unit... 5
Connect to water ............... 6
Connect to drain................. 7
Alternate drain method...... 7
Electrical requirements ..... 8
Grounding method ............ 8
Changing the Bin Door
Panel and Lower Panel ....... 9
Operating Instructions ........ 9
Check Operation .................. 9
Things to Remember ......... 10
How the Ice Maker
1-800-422-1230
Call our Consumer Assistance Center
with questions or comments.
KITCHENAID? Automatic Ice Maker
PART NO. 2181133
Model: KUIS185
49
[се Maker Safety
Before you plug it in
Your safety and the safety of others is very important.
“| We have provided many important safety messages in this manual and on your
| appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the
word “DANGER” or “WARNING.” These words mean:
You will be killed or seriously injured
A DAN С Е В if you don’t follow instructions.
You can be killed or seriously injured
AWAR N | N С if you don’t follow instructions.
All safety messages will identify the hazard, tell you how to reduce the chance of injury,
and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of fire, electric shock, or injury when using your ice
maker, follow these basic precautions:
* Plug into grounded 3 prong outlet. e Disconnect power before cleaning.
* Do not remove ground prong. Disconnect power before servicing.
* Do not use an adapter. ® Replace all panels before operating.
* Do not use an extension cord. e Use two or more people to move or install
ice maker.
— SAVE THESE INSTRUCTIONS —
eneral Information
AWARNING
Excessive Weight Hazard
Use two or more people to move and
install ice maker.
Failure to do so can result in back or
other injury.
Unpack
. Lay carton on rear face and break open
bottom flaps.
2. Set carton upright with all four
flaps outward.
. Lift carton up and off of machine.
4. Remove all tape and packaging materi-
als from the outside and inside of the Remove
cabinet. interior
NOTE: The Installation Instructions are packing
located in a plastic bag inside the ice bin.
5. Remove the lower access panel by Open bottom flaps
removing the two screws securing the
grille at the bottom and the one screw at
the top, and lift it free of cabinet.
6. Turn the fan by hand to make certain it
moves freely.
7. Loosen thumb screws holding cutter grid
and water pan to “thumb tight.”
8. Replace the lower access panel and
the screws.
Ww
Utilities required
(observe local codes)
Each installation is unique but will require:
1. A cold water inlet of 14" (6 mm) OD soft
copper tubing and a shut-off valve.
Water Electricity Drain
continued on the next page
3
General Information
2. A properly grounded 115 Volt, 60 Hz,
AC only, 15 ampere fused electrical
circuit, installed in accordance with the
National Electrical Code and with local
codes and ordinances.
NOTE: For proper location, see the
Built-In Opening Dimensions diagram
on page 6.
3. Either a gravity drain system or a sump
pump to lift the water to an existing drain.
Thermostat calibrations
If ice maker is to be operated at an elevation
of 2,000 feet (600 m) or more above sea
level, both the Bin Thermostat and the Ice
Thickness Thermostat will need to be
recalibrated. Call your dealer or an autho-
rized service group to have the necessary
changes made.
Shipboard operation
When this ice maker is installed aboard a
ship, it may be necessary to purchase and
install a water deflector. The deflector hangs
between the lower edge of the evaporator
and the cutter grid. It keeps the water
flowing over the evaporator from spilling into
the storage bin area. Order the necessary
parts from your local ice maker dealer.
[nstallation
Locate unit
1.
Place unit so the front side will be
completely unobstructed to provide
proper airflow.
. Area should be well ventilated with tem-
perature above 55°F (13°C) and below
110°F (43°C). Best results are obtained
between 70°F (21°C) and 90°F (32°C).
. Provisions for electricity, water, and
drain connections should be determined.
. The unit may be closed in on the top and
three sides, but the front must be unob-
structed for air circulation and proper
operation. Installation should be such
that the cabinet can be moved forward
for servicing, if necessary.
This unit
must be 90°F
installed in (32°C)
an area
protected
from the 70°F
elements, (21°C)
such as wind,
rain, and
water spray
or drip.
BEST
RANGE
| Go)
Level unit
1
. After placing unit in position, check to
make certain the unit is level side-to-side
and front-to-back.
. Accurate leveling is essential for proper
operation.
. Unit should be shimmed so that it is solid
as well as level. The shims should be of
hard, permanent type material.
. If you are installing this ice maker in a
commercial setting that requires National
Sanitation Foundation (NSF) installation
procedures, NSF requires that the ice
maker be sealed to the floor at the bottom
rail. For compliance with this NSF sealing
procedure, we recommend a silicone-type
sealer.
1 nstallation
Connect to water
(observe local codes)
1.
2.
Use 74" (6 mm) OD soft copper tubing for
the cold water supply.
Provide a convenient manual shut-off
valve in the water line.
. Position the tubing so it can enter the
access hole located in the right hand rear
of the cabinet. The tubing should extend
beyond the cabinet front when the
cabinet is pushed back into position.
. Always purge the water line before
making the final connection to the inlet of
the water valve to prevent possible water
valve malfunction.
- Slide the cabinet into place, bringing the
tubing through the rear access hole. Bend
the tubing to meet the connection at the
water valve. The garden hose threaded
compression fitting is found in the parts
bag, which is shipped under the ice
scoop. This joint provides a convenient
disconnect for service. Be sure the tubing
is clear of compressor to prevent rattle.
%" (19 mm)
| 23%" (606 mm)
a" (6 mm)
OD water line
compression
fitting at
water valve
Bend field-
supplied
water line to N
RIGHT END VIEW
= = око == = = == == о
<
me ew очков ав чо == #”
Water
inlet
solenoid
valve
Drain
ma tube
connect to re (95 mm)! | |
ing valve (190 mm) A =
BACK VIEW
17"
(200 mm)
м 7 4" (102 mm)
long 54" (16-
mm) rubber
drain tube —
341%" run to open
Hole for (874 mm)
field-
supplied
drain
74"
(190 mm)
water line — SIP gm
Da
(38 mm)
diameter
LITE standpipe
a |
ht
(76 mm) 4 A E
9" (229 mm)
BUILT-IN OPENING DIMENSIONS
90° И | XL 90°
34-1/2" »
Do not kink | |(s76 mm) 4-1/2" (114 mm)
or pinch -—+ to center line
supply cord | 5 N 9" (229 mm)
between ice Ep max.
maker and Locate outlet
cabinet. within this
space.
fr 18" (457 mm) J)
Connect to drain
(observe local codes)
1. The unit is provided with a gravity drain.
2. The ideal installation has a standpipe
(174" [32 mm] minimum) installed directly
below the outlet of the drain tube. Refer
to figures on the previous page for the
proper location of the standpipe.
3. It may be desirable to insulate drain line
thoroughly up to drain inlet.
4. Replace the lower access panel and its
SCrews.
Alternate drain method
If a drain connection directly below the drain
tube outlet is not available, install a drain
pump in the rear compartment of the ice
maker. The drain pump must meet these
specifications:
* |t must be U.L.-listed and have a U.L.-
listed, 120 VAC, 3-wire, grounded power
supply cord.
e Overall maximum outside dimensions:
15" (381 mm) wide x 6" (152 mm) deep x
9-7" (241 mm) high.
* Minimum pump flow rate: 24 gallons (91 L)
per hour (0.4 gallons [1.5 L] per minute) at
12 feet (3.7 m) lift.
* Operating temperature range: 55°F (13°C)
to 110°F (44°C).
AWARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
A Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or
electrical shock.
Electrical requirements
A 115 Volt, 60 Hz., AC only, 15 ampere It is recommended that a separate circuit,
fused electrical supply circuit, properly serving only this appliance, be provided.
grounded in accordance with the National Use a receptacle which cannot be turned off
Electrical Code and local codes and ordi- with a switch or pull chain. Do not use an
nances is required. extension cord.
Grounding method
For your personal safety, this appliance
must be grounded. This appliance is 3-prong grounding-type
equipped with a power supply cord which wall receptacle O]
has a 3-prong grounding plug. To minimize ==
possible shock hazard, the cord must be 2, à Za
plugged into a mating 3-prong grounding т
type wall receptacle, grounded in accor-
o
dance with the National Electrical Code and >
local codes and ordinances. If a mating wall TE)
receptacle is not available, it is the personal <
responsibility and obligation of the customer
to have a properly grounded 3-prong wall
receptacle installed by a qualified electrician.
3-prong
grounding plug
( hanging the Bin Door
Panel and Lower Panel
For complete information on how to change the bin door panel and lower panel, refer to
the Use and Care Guide.
perating Instructions
* For complete operation information, refer Cutter grid
to the Use and Care Guide. Ya" x Yı" (19 mm x 19 mm)
* Before starting, wash out interior of cabinet 9%" (241 mm) ——e-
with a baking soda solution (2 tablespoons —
[26 g] soda to 1 quart [1 L] of warm water).
Rinse thoroughly.
* Make certain the water is turned on.
* Turn switch to the “ON” position.
IMPORTANT: Allow unit to run for 3 hours
before expecting ice and for 24 hours before
trying to set the thickness control.
85"
(216 mm)
( heck Operation
Vv Start the unit by turning the service Vv Use a flashlight to look through space
switch to “ON” and opening the line between the cutter grid and liner to
water valve. check for even water flow over freezing
plate. Unit must be level for proper
“” NOTE: Left is “OFF” — Middle is “ON” — operation.
Right is “CLEAN.” In “CLEAN” position,
only the pump operates. Vv Check for desired cube thickness and
after 24 hours adjust if necessary.
¢/ Water will not enter pump pan until Maximum ice yield will be obtained
freezing plate gets cold and machine with ice thickness at 4" (13 mm) to
goes into a harvest cycle. 5%" (16 mm).
‘Things to Remember
* Water enters only during the defrost cycle.
Therefore the first cycle will be completed
without water in the system.
* As the room and water temperatures vary,
so will the amount of ice produced. This
means that higher operating temperatures
will result in reduced ice production.
* The unit will shut off when ice in the
storage bin touches the bin thermostat
well and will automatically cycle to keep
the bin full.
* The storage bin is not refrigerated and
some melting will occur. This also varies
with the room temperature.
* The unit needs good air circulation to
perform efficiently. Keep the front grille and
the condenser clean.
e The water system needs to be cleaned
periodically for good circulation. Instruc-
tions are located in the Use and Care
Guide.
How ihe Ice Maker Works
* Compressor runs
* Condenser fan runs
* Water pump runs (circulates water)
e Cutter grid is warm to touch
When the desired ice slab thickness is
reached, the harvest cycle begins and
the following happens:
es Evaporator thermostat is satisfied
* Compressor keeps running
* Condenser fan stops or turns very slowly
* Water pump stops
* Hot gas solenoid opens
e Water inlet valve opens
e Excess water is flushed out of the
drain pan
e Cutter grid is warm to the touch
NOTE: Normal harvest cycle takes 1 to
2 minutes.
Machine resumes freezing after slab is
released from evaporator and the cutting
process begins.
When the storage bin is filled, bin
thermostat opens.
* Cutter grid remains on
‘( Init Wiring Diagrams
This model operates at 115 volts except for voLTs == 80 HERTZ
the cutter grid circuit which operates at 8.5
volts at 1 amp. Maximum fuse size should
be 15 amps.
The compressor runs at all times except
when the Bin Thermostat becomes satisfied
and opens the circuit. This de-energizes the
system except for the transformer and cutter
grid.
Under normal operating conditions, when
the evaporator reaches the preset tempera-
ture (+10° to -3°F [-12° to -19°C], depending
on thickness of ice) the evaporator thermo- OVERÍÓAD compressons if! [ooo
stat opens, terminating operation of the fan y TRANSPORMER w — STARTRELAY | hor Ta
nena 157
motor and pump motor. The hot gas sole- — oe
noid and the water valve solenoid are A 8775 Y [vea
energized at this time and remain so until the 2 mm
evaporator reaches 38° + 2°F (3° + 1°C). AAV OT BE
CUTTER GRID GY | GRE
TRA(
AWARNING
“
Electrical Shock Hazard
Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death
or electrical shock.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project