installation instructions user guide

installation instructions user guide
INSTALLATION INSTRUCTIONS
USER GUIDE
Instructions d’installation
Guide d’utilisation
ActiveSmart™ refrigerator
Ice & Water and Non-Ice & Water
Réfrigérateur ActiveSmart™
Ice & Water et autres
RF135B, E522B, RF170W, RF170A, RF201A models
Modèles RF135B, E522B, RF170W, RF170A, RF201A
US CA
English
Page 1 – 52
Français
Page 55 – 106
CONTENTS
EN
Introduction3
Safety and warnings
4
Installation instructions
7
Moving or storing your appliance
21
Door conversion
22
Soft closing refrigerator door feature
ActiveSmart™ operating instructions
22
23
All about the external display (Ice & Water models only)
27
Using your water dispenser (Ice & Water models only)
28
Water filter (Ice & Water models only)
29
Using your ice maker (Ice & Water models only)
31
ActiveSmart™ special features (all models)
33
Cleaning and caring for your refrigerator
36
Storing food in your refrigerator
40
Storing food in your freezer
42
ActiveSmart™ user warnings and sounds
44
Troubleshooting45
Limited warranty
50
Filter performance data sheet
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may
not be available in all markets and are
subject to change at any time. For current
details about model and specification
availability in your country, please go to our
website www.fisherpaykel.com or contact
your local Fisher & Paykel dealer.
Note that the word ‘refrigerator’, throughout
this user guide, refers to the combination of
refrigerator/freezer products.
107
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
www.fisherpaykel.com
1
Introduction
EN
Thank you for buying a Fisher & Paykel ActiveSmart™ refrigerator.
At Fisher & Paykel we are very proud of this refrigerator. This refrigerator combines size
and storage space with the latest features and functions.
Thousands of hours of food care research and refrigeration experience has been
programmed into your refrigerator to give you the best possible performance.
We hope you enjoy your new refrigerator.
Refrigerator French door
and freezer drawer
Refrigerator door
and freezer drawer
Refrigerator door
and freezer door
Note: non Ice & Water models do not have an external water dispenser.
3
Safety and warnings
!
WARNING!
Electric Shock Hazard
Read and follow the safety and warnings outlined in this user guide before
operating this appliance.
Failure to do so can result in death, electric shock, fire or injury to persons.
Use this appliance only for its intended purpose as described in this user guide.
Important safety instructions
Warning!
When using this appliance always exercise basic safety precautions including the
following:
Danger
●●
●●
●●
●●
●●
●●
●●
●●
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Young children should be supervised to ensure they do not play with the appliance.
Refer to the stability bracket and leaflet supplied to avoid hazard due to instability of
the appliance.
The manufacturer’s installation instructions for product and cabinetry ventilation must
be followed when installing the appliance.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process.
Do not damage the refrigerant circuit.
In case of damage to the refrigerant circuit, ventilate the area by opening all windows.
Do not operate electrical equipment or any other equipment that may produce arcs,
sparks or flames in the area. Contact your Fisher & Paykel Authorized Service Agent
immediately to arrange for the appliance to be repaired.
Disposal
●●
●●
4
Extreme care must be taken when disposing your old appliance to avoid hazards:
– The refrigerant gas must be safely removed
–The doors should be removed and the shelves left in place so that children may
not easily climb inside.
Your Fisher & Paykel Authorized Service Agent will be able to give advice on
environmentally friendly methods of disposing of your old refrigerator or freezer.
Safety and warnings
EN
Cleaning
Many commercially available cleaning products contain solvents which may attack
plastic components of your refrigerator and cause them to crack. For further advice
please refer to section ‘Cleaning and caring for your refrigerator’.
Electrical
●●
●●
●●
●●
●●
●●
●●
●●
●●
This appliance must be installed in accordance with the installation instructions
before use.
Never unplug your refrigerator by pulling on the power cord.
Always grip the plug firmly and pull straight out from the outlet.
Do not plug in any other appliance at the same power point as your refrigerator or use
extension cords or double adapters.
Repair or replace immediately all electric service cords that have become frayed or
otherwise damaged. Do not use a cord that shows cracks or abrasion along its length
or at either the plug or appliance end.
If the power supply cord is damaged, it must only be replaced by your Fisher & Paykel
Authorized Service Agent because special purpose tools are required.
When moving your appliance away from the wall, be careful not to roll over or
damage the power cord.
Do not use electrical appliances inside the food storage compartments of the
appliance.
Do not remove the rear compartment cover. This can only be removed by Fisher &
Paykel Authorized Service Agents.
Important!
Your refrigerator is designed to operate for many years without the need for service
checks. However, if your refrigerator is malfunctioning, have it attended to by
your Fisher & Paykel Authorized Service Agent as soon as possible. All electrical
repairs must be carried out by an adequately trained service technician or qualified
electrician.
Storing food and drinks
●●
●●
●●
●●
●●
DO NOT store explosive substances such as aerosol cans with a flammable propellant
in this appliance.
Never store volatile or flammable materials in your refrigerator as they may explode.
Never freeze liquids in glass containers. Liquid expands during freezing, which may
cause the container to explode.
Never freeze carbonated drinks. They may explode.
Do not consume food if it is too cold. Food removed from the freezer compartment
may be cold enough to cause damage when brought into contact with bare skin, eg
frozen ice cubes.
5
Safety and warnings
Power failure – food safety
●●
Do not refreeze frozen foods that have thawed completely. The food may be
dangerous to eat. Follow the recommendations below if you discover food in your
freezer has thawed:
–Ice crystals still visible – food may be refrozen but should be stored for a shorter
period than recommended.
–Thawed but refrigerator cold – refreezing generally not recommended. Fruits
and some cooked food can be refrozen but use as soon as possible. Meat, fish,
poultry – use immediately or cook then refreeze. Vegetables – discard as they
usually go limp and soggy.
–Thawed and warmer than 41°F (5°C) – discard all food.
SAVE THESE INSTRUCTIONS
6
INSTALLATION INSTRUCTIONS
EN
Please follow the installation steps below to ensure your appliance operates correctly.
1. Power
●●
●●
●●
●●
The appliance must be installed so the plug is accessible.
To ensure that the appliance is not accidentally switched off, connect your refrigerator
to its own power point. Do not plug in any other appliance at this power point or use
extension cords and double adaptors, as the combined weight of both power cords can
pull the double adaptor from a wall outlet socket.
For power requirements, refer to the information on the serial plate located at the front
bottom right-hand side of the refrigerator when the door is open.
It is essential that the appliance is properly grounded (earthed).
2. Location
Your refrigerator should not be located in direct sunlight or next to any heat generating
appliance such as a cooktop, oven or dishwasher.
3. Ice & Water (Ice & Water models only)
●●
●●
Your Ice & Water refrigerator must be installed by an authorized plumber or Fisher &
Paykel Authorized Service Agent as incorrect plumbing can lead to water leaks.
Fisher & Paykel Appliances does not accept responsibility for damage (including water
damage) caused by faulty installation or plumbing.
7
INSTALLATION INSTRUCTIONS
Product and cabinetry dimensions
E
4. Freezer door models (RF135B, E522B)
(Ice & Water and non Ice & Water)
P
If integrating your refrigerator, please follow
Q
installation instructions provided with the
Q
integration kits.
F
Q
Q
Q
R
DA
PART: 838587
DA
7
8
P
9
DA
E
P B
Q
B
F
B
M
E
F
P
M
E
M
M
S
M
G
H/I
P
M
G
N
M
H/I
C
P H/I
M
M
PCS
C
M
F
S
S
R
Q
Flush with refrigerator chassis – full door rotation
G
R
P
M
N
DRAWING: 838587
6
P
T
N
K/L
P
M
P
K/L
T
T
K/L
P
Q
U
Flush with refrigerator door – full door rotation
R
G
P
M
H/I
v
T
J
M
P
N
O
K/L
W
C XP
Y
B
110VAC cord and water inlet dimensions
Flush with refrigerator door – 90° door rotation
RF135B
Product dimensions
8
E522B
inches
mm
inches
mm
A
Overall height of flat door product
67 17/32
1715
67 17/32
1715
A
Overall height of curved door product
–
–
66 15/16
1700
A
Overall height of curved door with
ice & water product
–
–
67 1/8
1705
B
Overall width of product
25
635
31 3/32
790
C
Overall depth of flat door product
(excludes handle, includes rear compartment cover)
27 3/8
695
27 3/8
695
C
Overall depth of curved door product
(excludes handle, includes rear compartment cover)
–
–
28 5/32
715
P
INSTALLATION INSTRUCTIONS
EN
RF135B
Cabinetry dimensions (including minimum clearances)
D
Inside height of cavity
E522B
inches
mm
inches
mm
68 5/16
1735
68 5/16
1735
Flush with refrigerator chassis – full door rotation
E
Inside width
26 9/16
675
32 11/16
830
F
Inside depth
24 13/32
620
24 13/32
620
31 3/32
790
37 7/32
945
–
–
26 25/32
680
27 3/8
695
27 3/8
695
29 11/32
745
35 7/16
900
–
–
26 25/32
680
27 3/8
695
27 3/8
695
Flush with refrigerator door – full door rotation
G
Inside width
H
Inside depth flush to curved door
I
Inside depth flush to flat door
Flush with refrigerator door – 90° door rotation
(for full drawer/shelf access, the doors need to be open past 90°)
J
Inside width
K
Inside depth flush to curved door
L
Inside depth flush to flat door
Minimum clearances
M
Side clearance
25/32
20
25/32
20
N
Side clearance – hinge side
flush with door – full rotation
5 5/16
135
5 5/16
135
O
Side clearance – hinge side
flush with door – 90° rotation
3 17/32
90
3 17/32
90
P
Rear clearance (incl. rear compartment cover)
1 3/16
30
1 3/16
30
Q
Vent – around top of cupboard (optional)
1 31/32
50
1 31/32
50
R
Top clearance – above refrigerator cabinet
1 31/32
50
1 31/32
50
S
Door clearance – hinge side
flush with chassis – full rotation
20 15/32
520
25 13/32
645
T
Door clearance – hinge side
flush with door – full rotation
15 15/16
405
20 7/8
530
40
1016
40
1016
110VAC AND WATER INLET DIMENSIONS
U
Power cord
V
Water inlet to bottom
5
127
5
127
W
110VAC to bottom
3
76
3
76
X
110VAC to edge
2
51
2
51
Y
Water inlet to edge
13
330
16
406
Note: these drawings and dimensions are also true for Ice & Water models.
9
S
INSTALLATION INSTRUCTIONS
Product and cabinetry dimensions
5. Freezer drawer models (RF170W, RF170A, RF201A)
P
(Ice & Water and non Ice & Water)
RF170W
F
Q
E
M
M
RF170A/RF201A
S
F
Q
Q
Q
R
R
G
PD A M
DA
H/I
B
C
E
ME
M
P
P
F
F
Q
Q
R
R
S
S
B
P
P
F
F
Q
Q
K/LH/I
T
P
M
M
P
N
C
E
ME
M
P
M
M
S
S
Q
Q
R
Flush with refrigerator chassis – full door rotation
Flush
R with refrigerator chassis – full door rotation
G
G
J
P
P
N
N
P
P
M
N
M
O
G
G
J
DA
P
P
N
N
P
P
M
N
M
O
E
DA
H/I
K/L
H/I
K/L
P
M
M
T
T
H/I
K/L
H/I
K/L
T
T
F
Q
B
CS P
Q
B
C
P
P
P
R door – full door rotation
Flush with refrigerator
J
M
P
N
B
C
10
G
N
H/I
K/L
T
P O
Flush with refrigerator door – full door rotation
N
T
P
J
N
O
K/L
P
Flush with refrigerator door – 90° door rotation
Flush with refrigerator door – 90° door rotation
INSTALLATION INSTRUCTIONS
RF170W
Product dimensions
EN
RF170A
RF201A
inches
mm
inches
mm
inches
mm
A
Overall height of product
67 17/32
1715
67 17/32
1715
70 15/32
1790
B
Overall width of product
31 3/32
790
31 3/32
790
35 7/16
900
C
Overall depth of product
(excludes handle, includes rear
compartment cover)
27 3/8
695
27 3/8
695
27 3/8
695
1735
68 5/16
1735
71 1/4
1810
Cabinetry dimensions (including minimum air clearances)
D
Inside height of cavity
68 5/16
Flush with refrigerator chassis – full door rotation
E
Inside width
32 11/16
830
32 11/16
830
37
940
F
Inside depth
24 13/32
620
24 13/32
620
24 13/32
620
37 7/32
945
41 23/32
1060
46 1/16
1170
–
–
–
–
–
–
27 3/8
695
27 3/8
695
27 3/8
695
Flush with refrigerator door – full door rotation
G
Inside width
H
Inside depth flush to curved door
I
Inside depth flush to flat door
Flush with refrigerator door – 90° door rotation
(for full drawer/shelf access, the doors need to be open past 90°)
J
Inside width
K
Inside depth flush to curved door
L
Inside depth flush to flat door
35 7/16
900
39 31/32
1015
44 9/32
1125
–
–
–
–
–
–
27 3/8
695
27 3/8
695
27 3/8
695
Minimum clearances
M
Side clearance
25/32
20
25/32
20
25/32
20
N
Side clearance – hinge side
flush with door – full rotation
5 5/16
135
5 5/16
135
5 5/16
135
O
Side clearance – hinge side
flush with door – 90° rotation
3 17/32
90
3 17/32
90
3 17/32
90
P
Rear clearance
(incl. rear compartment cover)
1 3/16
30
1 3/16
30
1 3/16
30
Q
Vent – around top of cupboard
(optional)
1 31/32
50
1 31/32
50
1 31/32
50
R
Top clearance – above refrigerator
cabinet
1 31/32
50
1 31/32
50
1 31/32
50
S
Door clearance – hinge side
flush with chassis – full rotation
25 13/32
645
12 25/32
325
14 3/8
365
T
Door clearance – hinge side
flush with door – full rotation
20 7/8
530
8 9/32
210
9 27/32
250
Note: these drawings and dimensions are also true for Ice & Water models.
11
INSTALLATION INSTRUCTIONS
U
v
W
X
Y
110VAC cord and water inlet dimensions
RF170W
110VAC AND WATER INLET DIMENSIONS
RF170A
RF201A
inches
mm
inches
mm
inches
mm
40
1016
40
1016
40
1016
U
Power cord
V
Water inlet to bottom
5
127
5
127
5
127
W
110VAC to bottom
3
76
3
76
3
76
X
110VAC to edge
2
51
2
51
2
51
Y
Water inlet to edge
16
406
16
406
18
457
Note: these drawings and dimensions are also true for Ice & Water models.
12
INSTALLATION INSTRUCTIONS
EN
6. Connecting water (Ice & Water models only)
Contents of filter kit
1 13 ft (4 m) white ¼” (6 mm) tubing
2 1 x 8” (200 mm) blue tubing
3 1 x pressure reducing valve (PRV)
4 1 x double sided tape
5 2 x locking keys
6 1 x water filter cartridge and head
7 1 x faucet connection
1
2
3
4
5
6
7
Important!
●●
●●
●●
●●
It is imperative the pressure reducing valve (PRV) is fitted prior to the filter. If the PRV
is not fitted to the connection line, the Ice & Water features may not function in some
circumstances.
The water connection to your Ice & Water refrigerator must be installed by an
authorized plumber or Fisher & Paykel Authorized Service Agent.
The water connection instructions below are intended only for the professional installer.
The new tubings supplied with the refrigerator are to be used, old tubings from old
Ice & Water connections should not be used.
Installation precautions/warning
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
DO NOT use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
WARNING – connect to potable water supply only.
DO NOT install on line pressure above 119 psi (827 kPa) or below 22 psi (150 kPa).
DO NOT use on hot water supply (100°F [38°C max.]).
DO NOT cut any length of tube shorter than 8” (200 mm).
DO NOT install near electrical wires or water pipes that will be in the path of drilling
when selecting the location of filter system.
DO NOT mount filter in such a position so that it will be struck by other items, such as
wastebaskets, etc.
DO NOT install the filter or any water tubing in direct sunlight as prolonged exposure
to light can weaken plastic components.
DO NOT install in a location that is susceptible to freezing temperatures as damage to
the housing could occur.
DO NOT screw filter to the refrigerator.
DO NOT install the filter or any water tubing in high temperature areas eg in a ceiling
cavity.
AVOID contamination of pipes during installation.
DO NOT use copper tubing. The plastic tubing supplied should always be used.
DO NOT continuously dispense water for longer than 2 minutes.
13
INSTALLATION INSTRUCTIONS
Installation instructions:
1 Ensure the refrigerator is NOT plugged into a
power supply.
2 Locate a cold water supply/feed only suitable
5
6
7
8
9
!0
PRV connection
Diagram 2
Waterline connection to
refrigerator
Diagram 3
Faucet connection
ET
4
Diagram 1
INL
3
for a water connection. Tee and tap fitting is
not supplied.
Connect the 8” (200 mm) blue tubing to the
outlet of the PRV (blue collet) and the inlet
connection of the water filter cartridge as
shown in Diagram 1. Gently pull on both ends to
ensure it is locked.
Connect the white ¼” (6 mm) tubing to the
outlet of the water filter cartridge as shown in
Diagram 2. Gently pull to ensure it is locked.
Measure the required length of tubing to run
from the PRV to the water connection point (no
less than 10” (250 mm)).
Cut the tubing making sure the ends are square
and clean.
Connect the tubing to the faucet connection
and the base of the PRV (white collet) and then
to the faucet as shown in Diagram 3. Please
note that the faucet connection supplied should
fit most installation situations.
Connect one locking key to each side of the
water filter cartridge in between the cartridge
and the locking collet as shown in Diagram 4.
To flush the water filter of any trapped air,
harmless carbon fines and to also check for
leaks, aim the end of the tubing into a bucket,
turn isolating faucet on and run at least 10 qt
(10 L) of water through. Once complete, turn
isolating faucet off.
Locate desired position for water filter noting
carefully the following points:
●●
It is recommended to fit the water filter in a
vertical orientation with the water filter head
at the top. This will minimize water leakage
when replacing cartridge.
●●
Ensure the filter is in a convenient location to
access every 6 months for replacement. We
suggest that this location is beside the water
filter supply faucet in a cupboard beside the
refrigerator.
●●
A minimum clearance of 2 ½” (64 mm) from
the bottom of the filter cartridge is required
to perform cartridge removal.
●●
Do not screw water filter to refrigerator.
Diagram 4
Locking key
14
INSTALLATION INSTRUCTIONS
EN
!1 Attach double sided foam to the
back of the water filter head as
shown in Diagram 5. Write the date
to be replaced on the filter (date
installed + 6 months). Remove the
double sided foam backing and
attach the filter to the desired
position, reinforcing the filter with
the screws provided as located in
step 10 (refer to the previous page).
Run the ¼” (6 mm) tubing to the
back of the refrigerator ensuring
there is enough tubing to pull the
refrigerator out for service.
Using the measurement guide
located on the rear compartment
cover as shown in Diagram 6. Mark
out 5/8” (16 mm), on the end of the
tubing as shown in Diagram 7.
Insert the tubing marked 5/8” (16 mm)
into the water (solenoid) valve up
to the marked line as shown in
Diagram 8.
Pull gently on tubing to ensure it is
locked in as shown in Diagram 9.
The completed installation should
look like Diagram 11 on page 16.
Turn the isolating faucet on and
check that all connections are dry
and free of drips.
Coil water line tubing behind the
refrigerator. Push your refrigerator
into place being careful not to
kink or squash the water line tube
running into the water (solenoid)
valve.
Read pages 16 – 17 carefully and
then turn refrigerator on.
PART: 838587
6
!3
6
!4
!5
!6
!7
!8
!9
8
9
Diagram 5
PART: 838587
6
!2
DRAWING: 838587
7
Double
sided foam
8
attachment
DRAWING: 838587
7
PART: 838587
9
DRAWING: 838587
7
8
9
Diagram 6
Diagram 7
Diagram 8
Diagram 9
Waterline connection to refrigerator
15
INSTALLATION INSTRUCTIONS
Important!
●●
●●
●●
●●
●●
All connections must be checked for leaks.
Ensure white ¼” (6 mm) tubing is routed away from sharp objects, sharp corners
(beware of kinking the tube as this will stop water flow), clear of the refrigerator rear
compartment and not in a location where it can be kinked or squashed.
Ensure all push-fit connections are firmly pushed into place. The tube should push in
5/8” (16 mm) before reaching the stop.
If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully
inserted to avoid leaks.
To remove tube from connection points first turn off the isolating faucet. Gently push
the dispensing pad a few times using a glass or container to remove the static line
pressure. Push in the collet firmly while pulling back on the tubing at the same time,
as shown in Diagram 10.
PART: 838587
6
DRAWING: 838587
7
8
9
Diagram 10
Diagram 11
Connection to water supply
System tested and certified by NSF International against NSF/ANSI Standard 53 for the
reduction of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane, Mercury,
P-Dichlorobenzene, Toxaphene & Turbidity; against Standard NSF/ANSI 42 for the
reduction of Chlorine Taste and Odor and Nominal Particulate Class I to a capacity of
750 gallons (2,838 liters).
16
INSTALLATION INSTRUCTIONS
EN
Before you start using your Ice & Water refrigerator
●●
●●
●●
●●
●●
●●
●●
Check your refrigerator is switched on.
Check that the isolation tap has been connected and turned on.
Run through and discard the first 3 qt (3 liters) of water from your water dispenser,
stopping intermittently to remove trapped air in the system. Failure to do this will result
in excessive dripping from your dispenser.
Note: there will be a 1 – 2 minute delay while the tank fills until water is dispensed.
Turn the ice maker on by pressing the
button. The light above the
button will be
illuminated when the ice maker is on.
Press and hold the
,
and
buttons together for 4 seconds and then close the
refrigerator compartment door to force an ice maker cycle. The ice tray will flip twice.
Repeat to force another ice maker cycle. The ice tray will flip twice and spill water into
the ice bin. Empty the water, dry and replace the bin. Note that the ice tray will not flip
until the refrigerator compartment door is closed.
Allow at least 2 hours for your refrigerator to cool before use.
Please discard the first 3 harvests of ice (8 cubes per harvest).
You are now ready to enjoy ice and water from your ActiveSmart™ refrigerator.
Water dispenser
Please note that once installation is complete a few drips may appear out of the
dispenser over the next few days as the remaining trapped air is cleared.
17
INSTALLATION INSTRUCTIONS
7. Installation (all models)
Your Fisher & Paykel ActiveSmart™ refrigerator
is fitted with front and rear rollers, designed
for moving the product in the forwards and
backwards direction.
Avoid moving the product in a sideways direction
as this may damage the rollers or the floor
covering/surface.
A Your refrigerator will arrive with the front feet
wound up making moving the product into its
final location a simple task.
Raise the front of
the refrigerator
Lower the front
of the refrigerator
Refrigerator feet
B Roll the refrigerator into its final position making
sure there is the correct air gap between the
product and surrounding cabinetry. See minimum
clearance in cabinetry dimensions table.
C Adjust the front feet down until the refrigerator
is leaning backward with the front approximately
1/2” (10 mm) higher than the back. This will ensure a
good door closing action.
(Non French door models only)
D Aligning your refrigerator with cabinetry.
●●
●●
●●
Align the sides of the refrigerator with the
cabinetry by adjusting the hinge side front foot.
Adjust the handle side foot until it touches the
floor and takes a small amount of weight.
Once the refrigerator is in place and aligned with
cupboards/alcove gently push on the front top
and check if the product is rocking or stable.
Uneven door alignment
8. Levelling of refrigerator doors
(French door models only)
●●
●●
●●
For uneven surfaces, front feet can be used to align
the 2 doors.
If left hand door is too low, then unscrew the left
hand foot to lift up the cabinet until the two doors
top edges are aligned.
If right hand door is too low, then adjust the right
hand foot in the same way.
Even door alignment
18
INSTALLATION INSTRUCTIONS
EN
9. What to do if your product is unstable
A Gently push the refrigerator back until the rear
rollers contact the floor.
●●
Measure the gap under the front foot, which has
come off the floor.
●●
Obtain some solid packing material (hardwood,
plastic, etc) which fits firmly into the gap under
the foot.
Example only
Note: do not use metallic materials that may
corrode, stain and/or damage floor coverings.
B Wind both front feet up and roll the product out
of position.
●●
Place the packing material in the location
diagonally opposite the front roller that lifts off
the floor.
●●
Make sure the packing material stays in place
when the product is pushed back into position.
●●
Ideally, the packing material is large enough to
rest against the back wall so as to prevent it
from moving when the cabinet is pushed into
position.
Unlevel floor
This foot lifts off the floor when
top front is gently pushed back
Unstable refrigerator
Packing material goes under rear roller
diagonally opposite front foot that lifts
Wall behind refrigerator
Stabilizing your refrigerator
For example: if this foot lifts off the floor when
pushing gently on the top front of the refrigerator
C Roll the refrigerator back into position and adjust front feet as per step 7 C.
(Check alignment and door closing action are satisfactory).
●●
Make small adjustments to front feet where necessary.
●●
Check that the product is stable (all 4 feet are on the floor). If not, repeat
9 A and 9 B.
19
INSTALLATION INSTRUCTIONS
Before placing food in the fresh food or freezer compartments
●●
●●
●●
●●
Remove all internal packaging. Ensure that all transit clips are removed from the
refrigerator. These are small rubber stoppers located at the back of the shelves.
Clean the inside of the appliance with a mix of warm water and a small amount of liquid
detergent, and a soft cloth to remove manufacturing and transportation dust.
Allow the refrigerator and freezer to run empty for 2 – 3 hours to allow each
compartment to cool to the appropriate temperature.
The appliance may have an odor on its initial operation, but this will go when the
refrigerator and freezer have cooled sufficiently.
Energy efficiency
●●
●●
●●
●●
●●
●●
●●
●●
●●
20
For the most energy efficient use of your appliance:
Ensure your refrigerator has adequate ventilation.
Do not cover your appliance with any material that will prevent air from flowing around
the cabinet sides.
Ensure you vacuum around the appliance to remove dust and possible pet hair
accumulation. Also keep the appliance and it’s cabinetry free of dust by wiping down
with a dry, lint-free cloth (refer to section ‘Cleaning and caring for your refrigerator’,
‘Rear compartment cover’).
Allow good clearances in front of air ducts within the cabinet for maximum cold air
distribution.
Cool hot foods down before placing them in the appliance.
Do not overfill the compartments.
Keep door openings to a minimum.
Select a temperature setting that isn’t too cold.
Check your door seals for leaks.
Moving or storing your appliance
EN
If your refrigerator is turned off for any reason, wait 10 minutes before turning it back
on. This will allow the refrigeration system pressures to equalize before restarting.
Moving your refrigerator
●●
●●
●●
●●
Turn off the appliance and unplug from the power point. Remove all food.
Turn the adjustable feet to the right as far as they will turn.
Ease the refrigerator out of its position. Tuck the power cord away, tape the shelves in
place and tape the doors closed. If the cabinet needs to be placed at an angle or laid
down, carefully lay it on its side (the right hand side when viewed from the front).
Relocate and install. If the appliance has been left on its side for any length of time,
leave it standing upright as long as you can (a few hours) before turning on.
Storing your refrigerator
●●
●●
When storing your cleaned appliance, leave the doors open. This allows air to circulate
and prevents the build up of bacteria and moulds.
Before using again, clean well using a mixture of warm water and a small amount of
liquid dishwashing detergent. Rinse with clean water and dry with a soft lint-free cloth.
Holiday time
We recommend you leave your refrigerator operating while you are on holiday.
21
Door conversion
ActiveSmart™ refrigerator models with silver handles need to be ordered at the point of
purchase either with left or right opening doors and can not be interchanged.
All other models need to have an appropriate conversion kit for that model refrigerator.
The kit is available from your Fisher & Paykel Authorized Service Agent or Dealer. Full
instructions are included in the conversion kit.
If you need to hinge your door on the opposite side we recommend that you call your
local Fisher & Paykel Authorized Service Agent or Dealer to make this conversion.
This does not apply to French door models.
Soft closing refrigerator door feature (where fitted)
The fresh food compartment of your refrigerator has been fitted with a soft closing door
feature. You do not need to push the door fully closed as this feature will automatically
close the door from a 45° (approximate) opening angle.
All soft close models
You may notice a little more resistance when opening the door(s) to what you are used to.
The closing speed of the door(s) decelerates at the end of closing. This is to prevent the
door(s) from slamming and to ensure your food items are cared for.
●●
●●
●●
The
The
The
The
speed of soft closing can depend on:
load stored in the door shelves.
temperature of the fresh food compartment.
ambient temperature.
French door soft close models only
The soft closing feature enables you to shut either the left or right door first.
You may notice that the closing speed of the left hand door is slightly faster than that of
the right hand door. This is perfectly normal.
The freezer drawer is fitted with an additional mechanism to soft close within the last
2” (50 mm).
Important!
●●
●●
22
Keep hands and food items clear of the door opening when the gap is less than 45°
(the soft close activation range).
The soft closing feature is located inside the door cavity therefore it is not serviceable
by the user. If a problem occurs, please contact your Fisher & Paykel Authorized
Service Agent.
ActiveSmart™ operating instructions
Models:
25” (635 mm) wide
31 1/8” (790 mm) wide
35 3/8” (900 mm) wide
EN
RF135B
E522B, RF170W, RF170A
RF201A
The control panel enables you to view and modify all the features and options on
your refrigerator.
Temperature control (all models)
●●
●●
●●
When the refrigerator is first turned on, the powerful cooling system will automatically
cool both refrigerator and freezer compartments to their set temperatures. This will
take between 2 – 3 hours.
The two compartment temperatures are accurately and independently controlled and
do not change with the temperature or humidity of the surroundings; whether summer
or winter.
If you wish to alter the temperature of either the fresh food compartment or freezer
compartment, this can be easily done by using the internal control panel located at the
front right of the refrigerator compartment.
Internal control panel to adjust temperatures
Internal control panel for
Tasman models
Internal control panel for
Designer and Elegance models
Internal control panel for
Ice & Water models
23
ActiveSmart™ operating instructions
Fresh food compartment (all models)
●●
●●
●●
The fresh food compartment light will automatically be illuminated. The temperature for
this compartment will show as a series of lights.
The temperature may be altered by pressing the
or
buttons. One press on either
of these buttons will reduce or increase the number of lights by one which indicates a
small change in temperature.
Fewer lights illuminated means a cooler temperature for the compartment selected.
Freezer food compartment (all models)
●●
●●
●●
●●
●●
To adjust the freezer temperature press the button once so the freezer compartment
light is illuminated.
The freezer temperature can be altered by pressing the
or
buttons.
One press on either of these buttons will reduce or increase the number of lights
illuminated which indicates a small change in temperature.
Fewer lights illuminated means a cooler temperature for the compartment selected.
Note: successively pressing the button will automatically scroll between the
compartments.
When the door is re-opened the control panel will return automatically to the fresh food
compartment setting.
Alarm Mute (all models)
For times when you require the door to be open longer than normal eg when cleaning
the interior of your refrigerator press the ‘Alarm Mute’ button to silence the door alarm
for 20 minutes.
●●
●●
●●
To activate, press the
button once. The ‘Alarm Mute’ light will be illuminated when the
function is activated.
‘Alarm Mute’ will deactivate after 20 minutes and the door alarms will return to normal.
To deactivate ‘Alarm Mute’ manually, press the
button again. When ‘Alarm Mute’ is
deactivated the light is off.
Note: when the fresh food or freezer compartment door is left open for long periods of
time food quality and / or safety may be compromised.
Door alarms (all models)
●●
●●
●●
If the fresh food compartment door is left open the alarm will beep after 90 seconds
and if the freezer door is left open the alarm will beep after 60 seconds.
While either door remains open, subsequent beeps will sound every 30 seconds for
5 minutes.
A continuous alarm will sound if either of the doors have been left open for 5 minutes or
longer and the interior compartment light(s) will turn off. The alarm will stop only when
the door(s) is closed.
Note: if ‘Alarm Mute’ has been activated the door alarms will be silenced for 20 minutes.
After 5 minutes of the doors being left open the compartment light will turn off however
the normal door alarms will be suspended. The ‘Alarm Mute’ light will be illuminated to
indicate that the appliance is in this mode.
24
ActiveSmart™ operating instructions
EN
Key Mute (all models)
‘Key Mute’ allows you to silence all button presses.
●●
●●
●●
●●
●●
●●
To activate ‘Key Mute’ and silence buttons, press and hold the
button for 4 seconds.
The
icon on the internal control panel will be illuminated.
The keys will be silenced when ‘Key Mute’ is activated.
Door alarms and ‘Bottle Chill’ alarm will still operate.
‘Key Mute’ will not automatically deactivate. To manually deactivate, press and hold the
button for 4 seconds.
The
icon will no longer be illuminated.
Key Lock (all models)
‘Key Lock’ allows you to disable the buttons on the internal control panel. This is useful
when cleaning your refrigerator.
●●
●●
●●
●●
●●
To activate ‘Key Lock’ press and hold the
and
buttons for 4 seconds.
The icon on the internal control panel will be illuminated.
Pressing any of the buttons will cause a raspberry beep to tell you that they are disabled.
‘Key Lock’ will not automatically deactivate. To manually deactivate, press and hold the
and
buttons for 4 seconds.
The icon will no longer be illuminated.
Sabbath mode activation (all models)
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
To activate ‘Sabbath mode’, open the door(s) of the fresh food compartment and
freezer compartment and then press and hold the
and
buttons on the internal
control panel for 4 seconds.
The candle icon will illuminate when ‘Sabbath mode’ has been activated.
When the product is in Sabbath mode:
The icon on the internal control panel will be illuminated.
All lights on the internal control panel except for the candle icon will be off.
The fresh food or freezer compartment lights will not operate when the door(s) is
opened.
The door alarms will not operate.
The internal control panel will not function except to indicate ‘Sabbath mode’ is active
as stated above.
Opening the door(s) will not affect the compressor or fans.
If the power to the refrigerator is turned off whilst in this mode, the product will
continue in ‘Sabbath mode’ when the power is restored.
‘Sabbath mode’ will automatically de-activate 80 hours after activation.
To de-activate earlier than 80 hours press and hold the
and
buttons for
4 seconds. The candle icon will no longer illuminate on the internal control panel (and
external display for Ice & Water models) and functionality of the internal control panel
will return to normal.
25
ActiveSmart™ operating instructions
Special Functions
Bottle Chill (Designer, Elegance and Ice & Water models only)
This function allows you to chill your beverages more rapidly in the freezer without the
worry of forgetting them. The timer is set for 15 minutes however the time taken to
chill depends on the size of your beverage. If after 15 minutes your beverage is not cold
enough, simply place it back in the freezer and reset the ‘Bottle Chill’ function.
●●
●●
●●
●●
To activate, press the button on the internal display. The ‘Bottle Chill’ light will be
illuminated when the function is activated. The icon will be illuminated on the external
display (Ice & Water models only).
An alarm will sound after the 15 minute time has elapsed.
–For non Ice & Water models: open the fresh food compartment door and press
the button on the internal control panel to silence the alarm.
–For Ice & Water models: the icon will flash on the external display. Press the
button on the external display to silence the alarm.
Remember to remove your beverage from the freezer.
To deactivate ‘Bottle Chill’ before 15 minutes has elapsed, press the button again on
the internal control panel. When ‘Bottle Chill’ is deactivated the light is off and the
icon is not visible on the external display (Ice & Water models only).
Fast Freeze (Designer, Elegance and Ice & Water models only)
We have created the ‘Fast Freeze’ feature to help you get the best possible results when
freezing fresh food. ‘Fast Freeze’ boosts the freezing speed by dropping the freezer to
its coldest temperature for 12 hours, which helps to ensure vital freshness, texture and
taste are retained during the freezing process.
●●
●●
●●
26
To activate, press the
button on the internal display. The ‘Fast Freeze’ light will be
illuminated when the function is activated.
To deactivate before the 12 hours has elapsed, press the
button again. When ‘Fast
Freeze’ is deactivated the light is off.
For best results we recommend that you activate the function before it is required.
Alternatively, activate it when placing food into the freezer.
All about the external display
(Ice & Water models only)
EN
This screen enables you to lock the water dispenser, indicates to you when ‘Bottle Chill’
is activated and when your water filter requires changing.
Electronic external display
EXTERNAL DISPLAY FEATURES
Dispenser lock button
and LED light
Locks/unlocks the water dispenser.
Bottle Chill indicator
Icon will illuminate indicating when ‘Bottle Chill’ is
activated and flashes when beverage is ready.
Filter change
indicator
Icon will illuminate indicating when water filter
requires changing.
When locked the LED above the button will
illuminate.
27
Using your water dispenser
(Ice & Water models only)
Dispensing
●●
●●
●●
Your water dispenser has been designed for one-handed
operation.
To dispense water push the dispensing pad gently, using a glass
or container. This pad requires only a gentle press to activate.
To stop the flow of water, simply pull your glass away from the
dispensing pad.
Please remember that pressing very hard against the
dispensing pad will not encourage the dispenser to operate
faster or produce greater quantities of water.
Water dispenser
First use
Please make sure you have read and followed page 17 before using your water dispenser.
Important!
To avoid damage to property or personal injury do not put hands, fingers or objects
up the dispenser opening.
Please note that once installation is complete a few drips may appear out of the
dispenser over the next few days as the remaining trapped air is cleared.
Dispenser Lock
The ‘Dispenser Lock’ prevents water from being dispensed. This
is useful when you are cleaning the external display or when
there are small children around.
●●
●●
●●
●●
28
Press and hold the
button for 4 seconds to activate
‘Dispenser Lock’.
The light above the ‘Dispenser Lock’ icon will be illuminated.
Pressing the water dispenser pad will cause a raspberry sound
indicating to the user that water cannot be dispensed.
To de-activate the ‘Dispenser Lock’, press and hold the
button for 4 seconds. The light above the ‘Dispenser Lock’
icon will no longer be illuminated and water dispensing will be
enabled.
Dispenser Lock
Water filter (Ice & Water models only)
EN
All the water to your refrigerator is filtered to remove impurities through a filter
cartridge located in a position of your choice outside the refrigerator. This will need
changing approximately every 6 months.
●●
●●
There is a replacement indicator icon
on the internal control panel and external
display which will appear when the filter needs replacing. It will flash, as a reminder,
when water is dispensed.
Replacement filter cartridges are available from your Fisher & Paykel Authorized Service
Agent. The details of the replacement filter cartridge are labelled on the cartridge.
Changing the water filter cartridge
It is not necessary to turn off the water supply before attempting to change the water
filter cartridge.
1 Grasp and firmly twist the cartridge in an anticlockwise direction (to the left when
installed in the recommended orientation).
2 Pull the cartridge away from the filter head (down when installed in the recommended
3
4
5
6
7
orientation).
– It is not unusual for a few drops of water to be present when the filter is removed.
Discard the old filter.
Filter installation:
– Remove protective cap on spigot on head.
–Push the cartridge up towards filter head while rotating it in a clockwise direction
(to the right when installed in the recommended orientation).
Reset filter indicator icon on the display (this will remind you when the filter is due to be
replaced again).
To flush the water filter of any trapped air, harmless carbon fines and to also check for
leaks, disconnect the tubing from the back of the refrigerator, aim the end of the tubing
into a bucket, turn isolating tap on and run at least 10 qt (10 liters) of water through.
Once complete turn isolating tap off. Reconnect the tubing.
A few drips may appear out of the dispenser over the next few days as the remaining
trapped air is cleared.
1
2
4
Changing the water filter cartridge
29
Water filter (Ice & Water models only)
To reset the filter indicator
Important!
●●
●●
●●
●●
We recommend the water filter to be used from the time of installation.
Do not reset indicator before filter is changed or filter monitoring will be inaccurate.
Press and hold and
for 4 seconds to reset the internal and external filter indicators.
The
icon on the internal and external displays will turn off when reset.
To disable the filter indicator
Note: if disabled, you will not be reminded to next change your filter.
●●
●●
●●
●●
When no filter is fitted, you can disable the filter indicator.
Press and hold
and
for 4 seconds to turn this feature off, the
icon will flash
once on the internal and external displays.
We recommend that you do not disable the filter indicator if you have a filter fitted to
the connection.
To turn this feature on press and hold
and
for 4 seconds, the
icon on the
internal and external displays will flash twice.
Important!
●●
●●
●●
●●
●●
●●
●●
●●
●●
30
To avoid serious illness or death, do not use the water filter where water is unsafe or
of unknown quality.
The water filter cartridge needs to be changed when the filter indicator icon flashes
on the interface panel.
We recommend the water filter cartridge is replaced when the internal and external
icons illuminate. This will happen every 6 months.
If the water filtration system has been allowed to freeze, replace filter cartridge.
The rate of water flow through the water dispenser can slow down as the filter
cartridge accumulates any sediments which may be present in the water supplied to
your home. This varies depending upon your local water quality, which may require
your filter cartridge to be changed more frequently.
In cases of excessively reduced filter life we recommend that you consult a local
plumber or your water supplier for advice on suitable filtration requirements for the
water supplied to your home.
Filter replacement is the consumer’s responsibility and will not be covered by the
warranty except in the case of faulty parts or materials within the filter cartridge.
If the water has not been dispensed for some time or water has an unpleasant taste or
odor, flush system by dispensing 10 qt (10 liters) of water.
If unpleasant taste or odor persists, you may wish to fit a new filter cartridge.
Using your ice maker (Ice & Water models only)
EN
Ice On/Off
Your ice maker is designed to automatically dispense ice
until it senses that the bin is full. So the more ice you use,
the more it makes. It is even clever enough to sense when
there is no bin in place to catch the ice and it will not
dispense any ice.
First use
●●
●●
●●
●●
●●
●●
When you first turn your refrigerator on after installation,
the ice maker will be off. The light above the ‘Ice On/Off’
icon will be off.
To turn your ice maker on press the
button. The light
above the ‘Ice On/Off’ icon will be illuminated when the
ice maker is on.
Press and hold ,
and
together for 4 seconds then
close the door(s). The ice tray will flip. Force another cycle.
The ice tray will flip and spill the water into the ice bin.
Empty water and replace bin.
If the bin is full of ice, inserted incorrectly or if all bins are
removed, the ice maker will not operate. When the bin is
inserted correctly the scoop will be on the right hand side
of the bin for models RF135B, E522B, RF170W and RF170A
and at the front of the bin for RF201A models.
Once your ice maker is in operation, discard the first
3 harvests of ice (8 ice cubes are produced per harvest).
This will flush away any impurities in the water line and
ensure that you get the best quality ice. We recommend
that you also do this after vacations or extended periods
of not using ice.
We recommend that you turn the ice maker off if:
–The water supply is to be off for several hours, or
–The ice storage bin is to be removed for a period of
time, or
– You are going on holiday/vacation.
Turning ice maker on
RF135A, E522B, RF170A
and RF170W
RF201A
Ice storage bin and
scoop in correct position
31
Using your ice maker (Ice & Water models only)
Information about your ice maker
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
Your automatic ice maker will produce approximately eight cubes of ice every
3 – 4 hours, depending on the freezer compartment temperature and the number of
door openings.
When the ‘Ice Boost’ function is activated, ice production will increase up to 25% from
standard ice making.
The ice cube tray will fill with water.
When cubes are frozen, they will be ejected from the ice tray into the ice storage bin.
Ice making will continue until the storage bin is full.
Ice making will resume once you start to use the stored ice.
Your Ice & Water product comes with a smaller ice bin inside the larger freezer bin.
Attached to the ice storage bin is the hygienic scoop for the ice. This scoop provides
hygienic access to the ice.
If a large amount of ice is required, remove an ice storage bin and allow ice to fall into
the larger bin.
For maximum ice storage, level the stored cubes with the ice scoop.
If ice is not used often, old cubes will become cloudy, taste stale, will shrink and may
stick together. Empty the ice storage bin periodically and wash in lukewarm water. Dry
thoroughly and place back into the correct position.
Ice boost function
This function is designed to be used for times when you require more ice eg when you
are having a party. The ‘Ice Boost’ function will increase ice production up to 30% from
standard ice making and deactivate automatically after 24 hours.
●●
●●
●●
●●
●●
●●
When you first turn your ice maker on, the ‘Ice Boost’ function will be off.
To turn this function on, press the
button. The light above the
button will be
illuminated when the ‘Ice Boost’ function is on.
The ‘Ice Boost’ function is paused once your ice bin is full.
To manually deactivate this feature press the
button again. The light above the
button will be off when the ‘Ice Boost’ function is off.
Activating the ‘Ice Boost’ function will automatically turn ice making on.
Deactivating ice making will automatically deactivate the ‘Ice Boost’ function.
Important!
●●
●●
●●
●●
32
Avoid contact with the moving parts of the ice maker ejector mechanism, and do not
place your fingers on the automatic ice making mechanism while the refrigerator is in
operation.
Do not use ice cubes that may have become discolored, usually with a greenblue color. If such discoloration is noted, discard the ice cubes and contact your
Fisher & Paykel Authorized Service Agent.
Ensure the ice maker is connected to the filter and to a drinkable water supply only.
Installation of the water connection to the ice maker must be completed by a qualified
service technician or a qualified plumber (refer to section, Installation instructions).
ActiveSmart™ special features (all models)
EN
Fruit and vegetable bins and humidity control lid
●●
●●
The fruit and vegetable bins feature a unique lid which provides two functions:
The humidity lid seals the bins and provides a humid microclimate to extend storage
times of fruit and vegetables.
The humidity lid prevents condensation, which forms at high humidities, from dripping
down onto the fruit and vegetables by retaining it in the grooves of the lid.
Fruit and vegetable bins and humidity slide
●●
●●
●●
●●
●●
Each fruit and vegetable bin has a humidity slide control that can be adjusted to a fruit
or vegetable setting depending on what is stored in the bins.
If possible try to store fruit and vegetables separately. This will help extend their
storage life.
If there is a mixture of fruit and vegetables in the bin adjust the position of the control
to the center.
If there is too much water in the bins (due to the high humidity in the bins), the control
can be adjusted towards the setting with fewer drips (fruit setting) and/or the water
can be wiped out as required.
Remember a minimum amount of water in the bins is beneficial for fruit and vegetable
storage.
Suitable for:
Salad
greens
Lettuce
Spinach
Broccoli
Cabbage
Carrots
Mixed fruit
& vegetables
Fruit with
skin/peel
Oranges
Lemons
Limes
Humidity control graphic
33
ActiveSmart™ special features (all models)
Slim storage drawer (where fitted)
The slim bins at the bottom of the fresh food
compartment provide storage space for items
that you may want to keep separate from the rest
of the refrigerator. These slim storage bins can
be used for deli item storage, beverages or for
defrosting foods.
Bottle holder (where fitted)
●●
●●
●●
●●
Slim storage drawer
The bottle holders can be used to store a variety of bottles.
To position the bottle holder in your refrigerator, simply slot the back edge of the bottle
holder onto the back trim of any shelf in the fresh food compartment.
If you are not using all or some of the bottle holders, the unused bottle holders can be
stacked up on top of one another so they do not take up unnecessary shelf space.
Bottles are best stored with the neck of the beverage facing the front of the refrigerator.
Glass shelves
●●
●●
Glass shelves can be repositioned in the cabinet as desired.
Remove shelves by lifting up the back of the shelf and then pulling the shelf forward.
Drip tray (Ice & Water models only)
●●
●●
●●
●●
34
The drip tray is designed to fit into
the bottom of the water dispenser
panel.
To insert the tray always ensure that
the rounded sides are fitted into the
dispenser panel first.
The purpose of the tray is to
capture any odd drips of water that
may fall after dispensing.
The tray can be easily removed for
cleaning.
Drip tray
ActiveSmart™ special features (all models)
EN
Manual ice system – RF170W and RF170A (non Ice & Water models only)
An ice storage bin which sits inside the upper top freezer bin provides storage for and
gives you access to clean, clear ice cubes.
Upper left freezer bin, ice storage bin, ice tray,
lid and scoop in correct position
Accessing your ice
Information about your manual ice system
●●
●●
●●
●●
●●
●●
●●
To make ice, take the ice tray and lid from the top of the ice storage bin. Remove the
lid from the ice tray and fill the tray with water. Place the lid back on the ice tray and
carefully position it back onto the ice storage bin.
Once the ice is solid, take the ice tray and lid off the ice storage bin, remove the lid from
the tray and twist the ice tray at each end in opposite directions. Turn the ice tray over
the ice storage bin to dislodge the cubes into the bin.
Fill the ice tray with clean water and repeat to fill the ice storage bin.
Attached to the ice storage bin is the ice scoop which provides hygienic access to ice.
To access ice cubes, take the ice tray and lid from the top of the ice storage bin and
place onto a flat surface. Take the scoop from the front of the bin, scoop cubes into
vessel and then replace the scoop, tray and lid back to the top of the bin.
For maximum ice storage, level the stored cubes around the bin with the ice scoop.
If ice is not used often, old cubes will become cloudy, taste stale, will shrink and may
stick together. Empty the ice storage bin periodically and wash in lukewarm water. Dry
thoroughly and place back in the correct position.
Ice trays and lid (all other non Ice & Water models)
●●
●●
●●
●●
To make ice, remove the lid from the ice tray and fill the tray with water. Place the lid
back on the ice tray and carefully position it on a flat surface in the freezer compartment.
To empty the ice cubes into the lid, hold the tray and lid together and twist the ends of
the tray in opposite directions to dislodge.
Refill the ice tray with water and store in the freezer.
Ice cubes are best stored in a closed container or plastic bag as they readily absorb
odors and tastes from other foods.
35
Cleaning and caring for your refrigerator
Exterior (all models)
Stainless exterior doors
●●
●●
●●
Clean the exterior door with liquid dishwashing detergent dissolved in warm water and
a soft cloth.
Dry the door with a lint-free cloth.
The use of any abrasive or stainless steel cleaners and solvents will damage the door
surface.
Other exterior surfaces (all models)
●●
●●
Clean all other exterior surfaces with a mix of warm water and liquid dishwashing
detergent, and a soft cloth.
If necessary, clean the magnetic door gasket and the center door gaskets with an old
toothbrush, warm water and liquid dishwashing detergent.
Rear compartment cover
●●
●●
●●
●●
●●
PART: 838587
6
To maximize operating efficiency regularly vacuum the
flooring around your appliance.
Cleaning behind the appliance is required once or twice a
year. More frequent cleaning may be necessary for dusty
homes or those with pets shedding hair.
To do this wind up the feet and carefully ease the
refrigerator out of its position. Switch off and unplug.
Vacuum the flooring behind your appliance and the rear
compartment cover to remove dust accumulation. Use a dry
lint-free cloth to clean the appliance walls and surrounding
cabinetry.
After cleaning, plug in and switch on. Push the appliance
into position and wind feet down.
DRAWING: 838587
7
8
Cleaning the rear
compartment cover
Warning!
Electric Shock Hazard. Do not remove rear compartment cover. This may expose you
to the risk of an electric shock.
Water dispenser pad and interface (Ice & Water models only)
●●
●●
We have incorporated a Dispenser and ‘Key
Lock’ function in your refrigerator to make
cleaning easier. This will help you to avoid
accidental water dispensing while you clean.
Clean the pad and interface panel with a soft
damp cloth.
Drip tray (Ice & Water models only)
●●
●●
36
To clean, take the tray out of the dispenser
panel and pull the two halves of the tray apart.
Clean in warm water with a mild detergent. Dry
and clip back together.
Cleaning the drip tray
9
Cleaning and caring for your refrigerator
EN
Interior (all models)
●●
●●
●●
●●
●●
●●
●●
It is important to keep the interior of the refrigerator and freezer clean to help prevent
food from becoming contaminated during storage.
The amount and types of food stored determines how often cleaning should be carried
out in the refrigerator (ideally once every 1 to 2 weeks).
Remove the shelves from cabinet and door. Wash shelves and storage bins in warm
water and detergent; rinse in clean water and dry before replacing.
Wipe over the interior surfaces with warm water and liquid dishwashing detergent.
Alternatively you can use 1 tsp baking soda dissolved in 1/2 qt (500 ml) of warm water.
Rinse with clean water.
To help remove “old stale refrigerator” smells add a few drops of vanilla essence or
vinegar to the water before cleaning.
Clean interior surfaces with warm water and liquid dishwashing detergent. Use a
toothbrush for the magnetic door gasket.
Do not use harsh, abrasive cloths on any part of the refrigerator or freezer.
Glass shelves (all models)
Clean with warm water and detergent or a glass cleaner.
Bottle holder (where fitted)
Clean with warm water and detergent. The use of abrasive cleaners and solvents may
cause damage.
Automatic ice dispenser (Ice & Water models only)
●●
●●
●●
●●
We do not recommend you clean the ice maker componentry, but it is important to
clean the bins occasionally.
The storage bin should be cleaned regularly and the old ice in the bottom of the bin
discarded.
Wash bin in lukewarm water. Dry thoroughly and replace.
When replacing the bin ensure that the scoop is on the right hand side or at the front of
the bin (model dependent).
Important!
Many commercially available cleaning products contain solvents that may attack
the plastic components of your refrigerator and cause them to crack. It is important
to use only warm water and a small amount of liquid dishwashing detergent on any
components inside and outside your refrigerator. Avoid using anti-bacterial cleaning
products on either the interior or exterior of the cabinet as they may cause rusting of
metal components and cracking of plastic components.
37
Cleaning and caring for your refrigerator
Humidity Control System
Important!
When cleaning the shelf above the vegetable
bins, we recommend that you do not
disassemble the Humidity Control System
from the shelf.
In the event that the humidity control lid
(plastic lid) and humidity slides become
separated from the glass shelf, follow these
instructions to reassemble.
Retainer
Humidity Slides
1 Turn shelf upside down
2 To attach humidity slides onto
shelf front corners, fit bottom
clips into shelf front trim. Next,
slide sideways towards shelf
until arm clips onto glass.
3 To attach humidity control
lid – with text facing you, align
lid with front of shelf. Hold
lid vertically and fit front end
into retainer on shelf. Ensure
lid fits into retainer as well as
underneath humidity slides.
4 At the sides of the shelf, adjust
humidity slide tabs so that the
plastic lid is between the shelf
and the tabs.
5 If clips on back of shelf are
present, fasten lid with rear clips.
Ensure that the cover is fully
secure at front and back of shelf.
Humidity Control System cleaning
38
Cleaning and caring for your refrigerator
EN
To remove trays or fixed bins
●●
●●
●●
●●
For ease of removal, empty food from
tray/bin first.
Hold the center front of the tray/bin
handle.
Lift vertically to unclip from the runners
and pull tray/bin towards you to remove.
Push both runners back into refrigerator.
Tray removal
To replace trays or fixed bins:
With the runners pushed back into the refrigerator, place the tray/bin on top of the
runners. Push the tray/bin back slowly until you feel it clip back onto the runners.
Important!
●●
●●
Ensure that trays and bins are securely clipped onto the runners before use.
Bin and tray runners are pre-lubricated, and will not need to be re-lubricated during
their life. Do not attempt to clean grease from the runners, as this will affect their
ability to function. Do not immerse runners in water.
Permanently fixed bins and trays (Freezer drawer models only)
The freezer bins and trays in this model are permanently fixed. They cannot be removed
from the freezer compartment. To clean simply wipe with a soft, damp cloth.
On vacation/holiday
●●
●●
●●
●●
●●
●●
Turn the ice maker to OFF on the internal control panel.
Shut off the water supply to the refrigerator.
On your return, turn on the water supply to the refrigerator.
Dispense 10 qt (10 liters) of water and discard to ensure the water tank is refilled with
fresh water.
Turn on the ice maker.
Discard the first 3 harvests of ice (8 ice cubes are produced per harvest).
39
Storing food in your refrigerator
Your refrigerator helps to extend the storage times of fresh perishable foods. The cold
temperature slows down the major causes of food spoilage – namely, the growth of
bacteria, moulds and yeasts, and any chemical and physical reactions.
Fresh food care
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
The quality of food before it is placed in the refrigerator is critical to successful
storage. For best results:
Select foods that are very fresh and of high quality.
Buy only the amount that you will use within the recommended storage time. If you
buy extra, plan to freeze it.
Ensure that food is well wrapped or covered before it is stored. This will prevent
food from dehydrating, deteriorating in color or losing flavor and will help maintain
freshness. It will also prevent odor transfer. Fruit and vegetables need not be wrapped
provided they are stored in the vegetable bins of the refrigerator.
Make sure that strong smelling foods are wrapped or covered and stored away from
foods such as butter, milk and cream which can be easily tainted by strong odors.
Refrigerate fresh, perishable foods as soon as possible after purchase. If left at room
temperature for any length of time the rate of deterioration will be accelerated.
Avoid placing food directly in front of air outlets, as it may freeze and cold air needs to
circulate to maintain safe food storage.
Do not open the refrigerator door unnecessarily.
Cool hot foods down before placing them in the refrigerator. This should be done
quickly. It can be aided by placing the container of food in a bowl of ice and water;
renew the ice as necessary. (Note also that hot containers may damage shelves and
walls of the refrigerator).
Store raw and cooked food in separate containers or packaging to prevent cross
contamination.
In addition:
Keep the refrigerator clean. Wipe the inside walls and shelves frequently (refer to
section ‘Cleaning and caring for your refrigerator’) and place only clean containers in
the refrigerator.
Keep a close check on the quality of food in your refrigerator. Discard any food that
shows signs of spoilage. Pay particular attention to meat, fish and poultry, as these
foods are highly perishable. Use food within the recommended storage times.
Dairy foods and eggs
●●
●●
●●
40
Most pre-packed dairy foods have a recommended ‘use by/best before/best by’ date
stamped on them. Store them in the refrigerator and use within the recommended
time.
Butter can become easily tainted by strong smelling foods so it is best stored in a
sealed container.
Eggs should be stored in the refrigerator. For best results, especially when baking,
remove the eggs from the refrigerator two hours before they are to be used.
Storing food in your refrigerator
EN
Red meat
●●
●●
●●
Place fresh red meat on a plate and loosely cover with waxed paper, plastic wrap or foil.
Store cooked and raw meat on separate plates. This will prevent any juices lost from the
raw meat contaminating the cooked product.
Delicatessen meats should be used within the recommended storage time.
Poultry
●●
●●
●●
Fresh whole birds should be rinsed inside and out with cold running water. Dry and
place on a plate. Cover loosely with plastic wrap or foil.
Poultry pieces should also be stored this way. Whole poultry should never be stuffed
until just before cooking, otherwise food poisoning may result.
Cool and refrigerate cooked poultry quickly. Remove stuffing from poultry and store
separately.
Fish and seafood
●●
●●
●●
Whole fish and fillets should be used on the day of purchase. Until required, refrigerate
on a plate loosely covered with plastic wrap, waxed paper or foil.
If storing overnight or longer, take particular care to select very fresh fish. Whole fish
should be rinsed in cold water to remove loose scales and dirt and then patted dry with
paper towels. Place whole fish or fillets in a sealed plastic bag.
Keep shellfish chilled at all times. Use within 1 – 2 days.
Precooked foods and leftovers
●●
●●
●●
These should be stored in suitable covered containers so that the food will not dry out.
Keep for only 1 – 2 days.
Reheat leftovers only once and until steaming hot.
Fruit and vegetable bins
●●
●●
●●
●●
●●
Although most fruit and vegetables keep best at low temperatures, take care not to
store the following at temperatures of less than 44.6°F (7°C) for long periods: Citrus
fruit, tropical fruit, tomatoes, cucumbers.
Undesirable changes will occur at low temperatures such as softening of the flesh,
browning, accelerated decaying and/or loss of flavor.
Do not refrigerate avocados (until they are ripe), bananas, mangoes or pepinos.
If possible store fruit and vegetables separately, ie fruit in one bin and vegetables in the
other.
Each fruit and vegetable bin has a humidity control slide that can be adjusted
depending on what is stored in the bins. For more information on using the Humidity
Control refer to section ‘ActiveSmart™ special features’.
41
Storing food in your freezer
The use of temperatures of -0.4°F (-18°C) or colder to store food means that the food
can be kept for longer periods than when refrigeration temperatures are used. This
is because the growth of bacteria, moulds and yeasts are stopped, and chemical and
physical reactions are severely restricted at such low temperatures.
Frozen food care
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
For best results:
Choose only high quality foods that freeze well.
Store at -0.4°F (-18°C) or colder. Take care to maintain this low storage temperature,
eg try to avoid opening the freezer door unnecessarily. If your ice cream is soft you are
running your freezer too warm.
Leave space at the top of containers, glass jars or plastic bags containing liquids or
semi-solid foods. These expand as they freeze. Usually 1 to 2” (20 – 50 mm) head space
is recommended. Seal. Ideally, remove all the air from the package after food is frozen.
Packages or containers of solid foods should have the air removed from them and be
sealed tightly before freezing.
Use the ‘Fast Freeze’ function when freezing fresh food. This helps to speed up the
freezing process, giving optimum freezing results. It is recommended that the function is
activated approximately 2 hours before required.
Freeze immediately or as quickly as possible. Freeze only small quantities of food at any
one time. For best results we recommend that only 2.2 pound (1 kg) of food be frozen
per 6.6 gal (25 L) or 0.88 cubic feet of freezer storage volume at any one time. (About
6.6 pound (3 kg) in small freezers and 8.8 pound (4 kg) in larger freezers). For faster
freezing in ActiveSmart™ models, we recommend that fresh food is placed at the top of
the freezer compartment close to the air vent.
Thaw foods preferably in a refrigerator, or using a microwave oven or multifunction
oven.
Keep a constant turnover of food. Use older items of food first and do not exceed
recommended storage times.
Use good quality freezer proof packaging to maintain food quality.
If food is only covered in plastic film place inside a freezer-proof plastic bag.
Recommended freezer storage times
These times should not be exceeded.
42
Months
Type of food stored
1
Bacon, casseroles, milk
2
Bread, ice cream, sausages, pies – (meat and fruit), prepared shellfish,
oily fish
3
Non-oily fish, shellfish, pizza, scones and muffins
4
Ham, cakes, biscuits, beef and lamb chops, poultry pieces
6
Butter, vegetables (blanched), eggs whole and yolks, cooked crayfish,
minced meat (raw), pork (raw)
12
Fruit (dry or in syrup), egg whites, beef (raw), whole chicken, lamb
(raw), fruit cakes
Storing food in your freezer
EN
Meat, poultry and game
●●
●●
●●
●●
Do not try to freeze more than 2.2 pound (1 kg) meat per 6.6 gal (25 L) or 0.88 cubic
feet of freezer storage volume at any one time. Meat must be frozen quickly in order to
maintain its texture.
Do not stuff poultry before freezing.
Red meat can be cooked from frozen, or from the partly or completely
thawed states. Remember to allow extra cooking time if cooking from frozen.
Always thaw poultry completely before cooking.
Fish
●●
●●
●●
Fish is best frozen commercially. If, however, you do want to freeze fish at home, make
sure the fish is very fresh and of high quality.
Clean, scale and preferably leave whole. All fish should be wrapped in two layers of
packaging as depending on the type of fish, odors and flavors can be readily transferred
either to or from it. Seal well.
For best results, cook from either the frozen or partly thawed state.
Fruit
●●
●●
●●
Choose high quality, mature, and ready to eat fruit. Preferably select varieties
recommended for freezing.
Avoid unripe and over-ripe fruit.
The way fruit is packed depends on how it is to be used. Fruits packed in syrup are ideal
for desserts, whereas fruits packed without sugar are better used for cooking. Most
fruits can be stored for 8 – 12 months.
Vegetables
●●
●●
●●
●●
●●
●●
●●
Most vegetables freeze well, although ‘salad’ vegetables lose their crispness. Other
vegetables, eg celery, onion and tomatoes, should only be used in cooked dishes as they
soften on freezing.
Freeze only high quality, mature, ready-to-eat vegetables.
Sort and discard any vegetables that are damaged.
It is necessary to blanch most raw vegetables prior to freezing.
Blanching involves a short cooking period during which vegetable enzymes are
destroyed. If these enzymes are not destroyed they cause undesirable physical and
chemical changes during freezer storage.
Vegetables can be blanched in boiling water, steam or microwave oven.
If using boiling water, boil vegetables for 2 – 4 minutes and cool quickly.
In general, frozen vegetables are best cooked from their frozen state.
Prepared and cooked foods
●●
Most cooked foods can be frozen but it is not recommended to freeze the following:
Cooked egg white, custards, cream fillings and milk puddings, gelatine or jelly-like
dishes, mayonnaise and similar salad dressings, meringue toppings. These tend to
separate on thawing.
43
ActiveSmart™ user warnings and sounds
User warnings
Faults
In the unlikely event a fault occurs the
icon will illuminate on the internal control
panel and an alarm will sound when the fresh food compartment door is opened.
●●
●●
Please count the number of beeps made when the fresh food compartment door
is opened. Please also take note of the number and sequence of temperature lights
displayed on the internal control panel and contact our Customer Care Center.
To silence the fault alarm press any button on the internal control panel. The
icon will
remain illuminated until the fault is corrected.
Normal refrigerator sounds
ActiveSmart™ refrigerators, with their excellent energy ratings and cooling performance,
can produce sounds somewhat different to your old refrigerator.
●●
●●
●●
●●
●●
●●
●●
44
Normal operational sounds include:
Fan air flow sound. ActiveSmart™ refrigerators have fans which change speed
depending on demand. During cooling periods, such as after frequent door openings,
fans circulate the cold air in the refrigerator and freezer compartments producing some
air flow sound. This is quite normal.
Cracking or popping which may occur when the defrost function is operating.
Running water sound. This is the liquid refrigerant in the system and can be heard as a
boiling or gurgling noise.
An audible hissing sound after closing the freezer door. This is due to the pressure
difference between the warm air that has entered the cabinet and suddenly cooled, and
the outside air pressure.
Other sounds may be heard for the following reasons:
– Cabinet not level.
– Floor uneven or weak.
– Bottles or jars rattling on shelves.
If this is your first refrigerator with an ice maker, you will hear occasional sounds that
may be unfamiliar. They are normal ice making sounds and are not cause for concern.
The following sounds are normal with the operation of an ice maker:
– Motor operation (low humming).
– Running water as the ice maker and/or water tank fills.
– Water valve opening and closing (hissing sound).
– Ice being loosened from the ice moulding tray (cracking).
– Ice dropping into bin (clunking).
Troubleshooting
EN
If there is a problem with your appliance, please check the following points before
contacting your local Fisher & Paykel Authorized Service Agent or the Customer Care
Center.
All models
Problem
Possible causes
What to do
Appliance does
not operate.
No electricity at power outlet.
Check that the plug is correctly
connected and power switched on.
Check another appliance at the
same outlet.
Check house fuse.
Light not
working.
Light not functioning.
The LED light cannot be serviced
by the user. Contact your Fisher &
Paykel Dealer or Fisher & Paykel
Authorized Service Agent.
Refrigerator not working.
Check refrigerator is turned on at
wall.
Light and
display not
working.
Product in ‘Sabbath Mode’.
Press and hold
for 4 seconds.
Motor operates
for long periods.
Hot weather.
Minimize door openings to allow
temperature to stabilize.
Frequent door openings.
,
and
together
Large amount of food
recently added.
Storage
compartments
too warm.
Temperature control set too
low.
Refer to section ‘Temperature
control’.
Doors not sealing properly.
Check that cabinet is level and
gasket seals are clean.
Temperature setting not
correct.
Refer to section ‘Temperature
control’.
Frequent door openings.
Minimize door openings to allow
temperature to stabilize.
Large amount of food
recently added.
Food freezing in
the refrigerator.
Unfamiliar
noises.
Temperature setting not
correct.
Refer to section ‘Temperature
control’.
Food placed directly in front
of air outlets.
Move chill sensitive foods away from
the center back of the shelves.
Cabinet not stable or level.
Refer to sections ‘Installation
instructions’ or ‘ActiveSmart™ user
warnings and sounds’.
Freezer is defrosting.
45
Troubleshooting
All models
Problem
Possible causes
What to do
Water in the
vegetable bins.
Condensation is formed by
the water produced by fruit
and vegetables.
A small amount of condensation is
beneficial for fruit and vegetable
storage.
Wipe out water with a cloth.
Set humidity slide to
low humidity setting
Exterior of
cabinet is warm.
This is normal.
Warm area on
central door seal
(French door
models only).
This is normal.
Condensation
on outside of
refrigerator/
freezer.
Not unusual during periods of
high humidity.
Wipe dry.
Condensation
inside fresh food
compartment.
Frequent or long door
openings.
Minimize door openings.
Door gasket leaking.
Check that gasket is sitting flat and
sealing tightly.
Not unusual during periods of
high humidity.
Wipe dry.
Door handles
out of
alignment.
With time and usage,
movement may occur.
Refer to section ‘Installation
instructions’.
Tray/bin does
not slide in and
out evenly.
Packaging trapped.
Check to ensure no food or
packaging is trapped behind the
tray/bin.
Runners not extending fully.
Holding onto sides of tray/bin,
extend the runners fully by using a
firm pull – this will reset the runner.
Taste of odor in
ice cubes
Transfer of odor/taste from
strong smelling foods.
Wrap or cover strong smelling foods.
Appliance
operating
inefficiently
Accumulation of dust on or
behind the rear compartment
cover.
Refer to section ‘Cleaning and caring
for your refrigerator’.
46
If problem persists please contact
Customer Care.
Troubleshooting
EN
Ice & Water models only
Problem
Possible causes
What to do
Automatic ice
maker does
not work.
Ice maker has not been turned on.
Switch on ice maker.
Bin is in the wrong way or there
is no bin in place.
Place bin so scoop is on the
right side.
Ice bin sits directly under ice
maker on top left side of freezer.
Ice cubes have
odor/taste.
Water supply turned off or not
connected.
Connect water supply.
Freezer compartment not working.
Contact Customer Care.
Water pressure too low.
Check water pressure.
Water line kinked/squashed.
Check water line for kinks/
squashing.
Filter clogged.
Water filter may need replacing.
Unsealed packages may be
transmitting odor/taste.
Old cubes need to be discarded.
Interior of freezer needs
cleaning.
Ice storage bin needs to be
emptied and washed.
Ensure food packaging is sealed.
Clean refrigerator.
Poor taste from incoming water.
Filter may need changing.
A new filter may need to be
installed.
Force 2 – 3 ice tray flips.
Slow ice cube
freezing.
Door may have been left ajar.
Close door.
Freezer compartment too warm.
Turn temperature to a colder
setting.
Warm spot on
central door
seal. (French
door models
only)
You may feel a warm spot
at times on the central seal
between the two refrigerator
doors.
This is perfectly normal and is
part of the normal refrigerator
operation.
47
Troubleshooting
Ice & Water models only
Problem
Possible causes
What to do
Wet ice/
ice clumping.
Low water pressure.
Check water pressure.
Filter blocked.
Replace filter.
Long freezer door openings.
Gently tap ice with scoop to
unstick or, if large clumps occur,
empty ice bin and make new ice.
High ambient temperature.
Ice bin left out of freezer
compartment for a length of
time.
Ice will stick together over time.
Water has poor
taste/odor.
Refrigerator not used for an
extended period.
Dispense 10 qt (10 L) of water so
fresh water supply is replenished.
Water dispenser
does not work.
Water supply turned off or not
connected.
Turn water on.
Water in first
glass is warm.
48
Press dispenser for 2 minutes to
remove trapped air from water
line and to fill the water system.
Supply line may be blocked.
Check supply for kinks or leaks.
On first installation there may be
air in water system.
To remove air, run 3 qt (3 L) of
water through the dispenser.
Filter may be blocked and need
replacing.
Replace filter (see back of this
booklet for Customer Care
contact details).
‘Dispenser Lock’ activated.
Press and hold the
4 seconds.
Water frozen in tank.
Increase temperature to a
warmer setting in fresh food
compartment and freezer.
Water dispenser not used for
extended period.
Discard first glass of water
dispensed.
Tank capacity used recently.
Allow water time to cool.
button for
Troubleshooting
EN
Ice & Water models only
Problem
Possible causes
What to do
Filter warning
is
light
flashing.
Filter needs replacing.
Replace filter as soon as possible.
Drips overflow
drip-shelf.
Air trapped in tank.
Flush 3 qt (3 L) water through
dispenser, stopping intermittently.
New filter installed.
Flush 10 qt (10 L) water through
filter and then 3 qt (3 L) through
dispenser.
Water flow rate
has slowed
down.
Filter cartridge is restricted.
Replace filter as soon as possible.
Ice buildup
inside freezer
compartment.
Freezer door not closing tightly.
Arrange items in freezer so door
can close tightly.
Ice maker makes
unfamiliar
sounds or seems
too loud.
Normal ice maker operation.
Refer to section ‘ActiveSmart™
user warning and sounds’.
Ice boost
function not
increasing
rate of ice
production.
Ambient temperature very warm.
Minimize door openings.
Check and clean door gasket seal.
Refrigerator is in high usage.
49
Limited warranty
When you purchase any new Fisher & Paykel ActiveSmart™ product for personal or
consumer use you automatically receive a two year limited warranty covering parts and
labor for servicing within the 48 mainland United States, Hawaii, Washington DC and
Canada. In Alaska the limited warranty is the same except that you must pay to ship the
product to the service shop or the service technician’s travel to your home. Products for
use in Canada must be purchased through the Canadian distribution channel to ensure
regulatory compliance.
If the product is installed in a motor vehicle, boat or similar mobile facility, you receive
the same two year limited warranty, but you must bring the vehicle, boat or mobile
facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.
You receive an additional three year limited warranty (for a total of five years) covering
parts and labor for sealed refrigeration system (compressor, evaporator, condenser, filter
dryer, and connecting tubing) within the 48 mainland United States, Hawaii, Washington
D.C. and Canada. In Alaska the limited warranty for the sealed refrigeration system is the
same except that you must pay to ship the product to the service shop or the service
technician’s travel to your home.
Fisher & Paykel undertakes to:
Repair or at its option replace without cost to the owner either for material or labor
any part of the product, the serial number of which appears on the product, which is
found to be defective within two years of purchase. In Alaska, you must pay to ship the
product to the service shop or for the service technician’s travel to your home. If the
product is installed in a motor vehicle, boat or similar mobile facility, you must bring
it to the service shop at your expense or pay for the service technician’s travel to the
location of the product. If we are unable to repair a defective part of the product after a
reasonable number of attempts, at our option we may replace the part or the product,
or we may provide you a full refund of the purchase price of the product (not including
installation or other charges).
This limited warranty extends to the original purchaser and any succeeding owner of the
product for products purchased for ordinary single-family home use.
All service under this limited warranty shall be provided by Fisher & Paykel or its
Authorized Service Agent during normal business hours.
How long does this limited warranty last?
Our liability under this limited warranty expires TWO YEARS from the date of purchase
of the product by the first consumer.
Our liability under any implied warranties, including the implied warranty of
merchantability (an unwritten warranty that the product is fit for ordinary use) also
expires TWO YEARS (or such longer period as required by applicable law) from the date
of purchase of the product by the first consumer. Some states do not allow limitations
on how long an implied warranty lasts, so this limit on implied warranties may not apply
to you.
50
Limited warranty
EN
This limited warranty does not cover:
A Service calls that are not related to any defect in the product. The cost of a service call
will be charged if the problem is not found to be a defect of the product. For example:
1 Correcting faulty installation of the product.
2 Instructing you how to use the product.
3Replacing house fuses, resetting circuit breakers, correcting house wiring or
plumbing, or replacing light bulbs.
4 Correcting fault(s) caused by the user.
5 Changing the set-up of the product.
6 Unauthorized modifications of the product.
7Noise or vibration that is considered normal, for example, drain/fan sounds,
refrigeration noises or user warning beeps.
8Correcting damage caused by pests, for example, rats, cockroaches, etc.
B Defects caused by factors other than:
1 Normal domestic use or
2 Use in accordance with the product’s user guide.
C Defects to the product caused by accident, neglect, misuse, fire, flood or Act of God.
D The cost of repairs carried out by non-authorized repairers or the cost of correcting
such unauthorized repairs.
E Travel fees and associated charges incurred when the product is installed in a location
with limited or restricted access. (eg airplane flights, ferry charges, isolated geographic
areas).
F Normal recommended maintenance as set forth in the product’s user guide.
G Filter replacement except in the case of faulty parts or materials within the filter cartridge.
H Damage (including water damage) caused by faulty installation or plumbing.
This product has been designed for use in a normal domestic (residential) environment.
This product is not designed for commercial use (whatsoever). Any commercial use by a
customer will affect this product’s limited warranty.
If you have an installation problem contact your dealer or installer. You are responsible
for providing adequate electrical, exhausting and other connection facilities.
We are not responsible for consequential or incidental damages (the cost of repairing
or replacing other property damaged if the product is defective or any of your expenses
caused if the product is defective). Some States do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
51
Limited warranty
How to get service
Please read your user guide. If you then have any questions about operating the
product, need the name of your local Fisher & Paykel Authorized Service Agent, or
believe the product is defective and wish service under this limited warranty, please
contact your dealer or call us at:
USA and Canada
TOLL FREE 1.888.9.FNP.USA (1.888.936.7872)
or use the link at: www.fisherpaykel.com/locator/servicer/
You may be required to provide reasonable proof of the date of purchase of the
product before the product will be serviced under this limited warranty.
No other warranties
This limited warranty is the complete and exclusive agreement between you and
Fisher & Paykel regarding any defect in the product. None of our employees (or our
Authorized Service Agents) are authorized to make any addition or modification to this
limited warranty.
Warrantor: Fisher & Paykel Appliances, Inc.
If you need further help concerning this limited warranty, please call us at above
number, or write to:
Fisher & Paykel Appliances, Inc.
695 Town Center Drive, Suite 180
Costa Mesa
CA 92626
This limited warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
52
107
108
www.fisherpaykel.com
Copyright © Fisher & Paykel 2015. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
Droits réservés © Fisher & Paykel 2015.
Les spécifications du produit contenues dans ce manuel s’appliquent aux
modèles et produits spécifiques comme décrits à la date de publication.
Dans le cadre de notre politique d’améliorations en permanence de nos
produits, ces spécifications pourront être modifiées à tout moment. Nous
vous recommandons de vérifier auprès de votre revendeur que ce manuel
décrit le produit actuellement disponible.
US CA
842117 A
02.15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement