Kodak | V600 Zoom | User's Manual | Kodak V600 Zoom User's Manual

Kodak V600 Zoom User's Manual
V600UserGuide.book Page 1 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector
KODAK V600 Zoom Digital Projector
With Kodak’s Exclusive Image Manager
User Guide
V600UserGuide.book Page 2 Tuesday, March 21, 2000 8:26 AM
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Canada
This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TUV, NOM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
Declaration of Conformity
Manufacturer: Eastman Kodak Company
Rochester, New York 14650 USA
We declare under our sole responsibility that the KODAK V600 Digital Projector and
KODAK V600 Zoom Digital Projector conform to the following directives and
norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMI: EN 55022 (1992) Class A
EMC: EN 50082-1 (1992)
IEC 801-2, IEC 801-3, IEC 801-4
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 1992 + A1 + A2 + A3: 1995
March, 2000
Australian Certification C-tick mark
V600UserGuide.book Page iii Tuesday, March 21, 2000 8:26 AM
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
If You Need Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 2
Online Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Faxed Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Telephone Customer Support . . . . . . . . . . . . . . . . . . . . . 3
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the Projector . . . . . . . . . . . . . . . . . . . . . . . . 6
Starting the Presentation . . . . . . . . . . . . . . . . . . . . . . 7
Using the Remote Control and Keypad . . . . . . . . . . . . 9
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . 10
Using KODAK Image Manager . . . . . . . . . . . . . . . . . . . 12
Adjusting the Display and Volume . . . . . . . . . . . . . . . 13
Setting Up the Image Source . . . . . . . . . . . . . . . . . . . 14
Selecting a Language . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Checking the Status. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
To reset lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Turning Off the Projector . . . . . . . . . . . . . . . . . . . . . . . 18
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changing the Lamp Module . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the Projection Lens . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the Exterior Case . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Image Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
iii
English
Table of Contents
V600UserGuide.book Page iv Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Safety Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Projector Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Battery Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
iv
V600UserGuide.book Page 1 Tuesday, March 21, 2000 8:26 AM
The easy-to-use KODAK V600 Digital Projector and KODAK V600
Zoom Digital Projector offer superb image quality at an affordable
price. Built into the V600/V600 Zoom Digital Projectors is Kodak’s
exclusive Image Manager feature. With this feature, you can select
the image display setting best suited for your specific presentation
material and projection environment.
In only minutes you can have your KODAK V600 Digital Projector
and KODAK V600 Zoom Digital Projector ready to go. Just connect
the projector to an image source such as a computer, DVD, VCR, or
digital camera.
If you are familiar with connecting and using digital projectors, refer
to the Quick Start Guide included with the projector. If not, follow
the directions in this user guide to connect your projector and run
your presentation.
What’s in the Box
Make sure that all of the following components were included with
the projector. Contact your dealer of KODAK products immediately
if anything is missing.
•
•
•
•
•
•
•
Soft carry case
Lens cap
Analog RGB (15 Pin HD) cable
S-video cable
Composite video cable
Stereo audio cable – 1/8” mini-plug
2 Power cords - US and European
(a UK power cord will be included where needed)
• User Manual
• Quick Start Guide
• Product registration card
• Remote control (included with V600 Zoom only)
• MACINTOSH adapter
For information on ordering projector accessories, visit our Web site
at www.kodak.com/go/projectors.
1
English
Introduction
V600UserGuide.book Page 2 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
If You Need Assistance
The first place to look for help is in “Troubleshooting” on
page 24. But you can also get help online, by fax, or by
phone.
Online Services
Contact Kodak via:
World Wide Web
http://www.kodak.com
(click on Service and Support)
America Online
(keyword) KODAK
CompuServe
GO KODAK
Kodak Internet List
Server
photo-cd@info.kodak.com; or
ftp.kodak.com
Faxed Information
Kodak offers automated support by fax:
2
U.S. and Canada
1-800-508-1531
Europe
44-0-131-458-6962
U.K.
44-0-131-458-6962
V600UserGuide.book Page 3 Tuesday, March 21, 2000 8:26 AM
If You Need Assistance
Telephone Customer Support
English
If you have questions concerning the operation of your KODAK
projector, you can speak directly to a customer support
representative. When you call, be at the image source and projector
and have the projector serial number ready.
In the U.S. and Canada call toll free:
1-800-23K-ODAK
9:00 a.m. and 8:00 p.m. (Eastern Standard Time)
Monday through Friday.
The International Toll Line is +44 (0) 131 458 6714.
In Europe call
Austria/Osterreich
01 795 67000
Germany/Deutschland
069 9509 6055
Spain/Espana
91 4069130
Belgium/Belgique
02 713 1398
Ireland/Eire
01 402 6815
Sweden/Sverige
08 587 70305
Denmark/Danmark
38 48 7088
Italy/Italia
02 696 33205
Switzerland/Schweiz/Suisse
01 838 5358
Finland/Soumi
0800 11 8043
Netherlands/Nederland
020 346 9128
UK (National Line)
0870 6061031
France
0141 918578
Norway/Norge
23 16 2041
3
V600UserGuide.book Page 4 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Austria/Osterreich
01 795 67000
Int. Fax Line
+44 (0) 131 458 6962
In other regions call:
4
Australia
613 9353-2261
Fax 613 9353-2567
Singapore/Malaysia/Indonesia/
India
65 4736 611
Fax 65 4798 397
Thailand
662 2713 040
Fax 662 6161 923
Philippines
632 8100 331 loc 223 or
416
Fax 632 8140 626
South Korea
822 7085 577
Fax 822 36721 450
HK/PRC
852 2564 9396
Fax 852 2562 4258
Taiwan
886 2-8938178
Fax 886 2-8951069
V600UserGuide.book Page 5 Tuesday, March 21, 2000 8:26 AM
Projector Features
Projector Features
English
keypad
remote
control sensor
focus ring
zoom ring
(V600 Zoom
model only)
foot release button (2)
connection panel
connection for
optional Kensington Lock
adjustable feet
5
V600UserGuide.book Page 6 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Connecting the Projector
PC/MAC connection
to the computer
monitor port
PC / MAC
S-Video
to the S-Video out port
S-VIDEO
VIDEO AUDIO
~
AC
100V
240V
Audio
to the source’s Audio out port
Video
to the Composite video
out port
Power cord connection
to an electrical outlet
The cables are color coded to assist you with making the connections.
When you connect the power cable to the projector, the Power light
on the keypad begins to blink.
You can connect more than one image source at a time. Use the Setup
tab on the menu screen to select which image source you want to
view. See “Setting Up the Image Source” on page 14.
If you are using an older MACINTOSH computer, you might need to
use the MACINTOSH adapter that was included with your projector.
Warning:Always turn off the image source (computer or video
source) and projector before connecting or disconnecting
cables.
6
V600UserGuide.book Page 7 Tuesday, March 21, 2000 8:26 AM
Starting the Presentation
We recommend turning on the projector and image sources in the
order listed here.
Note: You might not be using all of these components for your
presentation.
•
•
Video source such as VCR, DVD or digital camera.
Audio source if different from your video source or
computer
• Projector
• Computer
1. Connect the signal cable to the computer or video source.
2. Connect the power cord to the projector and to a power source.
The Power light begins to blink.
3. Turn on the presentation components in the order listed.
To turn on the projector, remove the lens cap and press the Power
button on either the remote control or the keypad.
power button
Power
Menu
Enter
Next
Adjust
POWER
MENU
ADJUST
ENTER
Volume
NEXT
The Power light stays a steady green when the lamp comes
on.
Either the title screen or the image from the image source
appears.
Note: Many laptop computers do not automatically turn on their
external video port when another display device is
connected. Refer to your computer’s user guide for the
function key or command that activates the port. MAC
users may need to turn on SimulSCAN or monitor
mirroring. Refer to the computer manual.
7
English
Starting the Presentation
V600UserGuide.book Page 8 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
4. Position the projector by using the adjustable feet on the bottom
of the projector. Press the foot release buttons on the front of the
projector to raise or lower the feet.
5. Turn the focus ring to focus the image and turn the zoom ring
(V600 Zoom model only) to zoom in or out on the image.
6. Make any necessary image adjustments by using the on-screen
menus. Press the Menu button to view the menu choices. Use the
Adjust + - buttons to go to the desired tab. Press the Menu button
again to dismiss the menus.
Go to the Kodak tab to select the type of content in your
presentation. See “Using KODAK Image Manager” on page 12.
Go to the Adjust tab to adjust brightness, contrast, color (video
only) and tint (video only). See “Adjusting the Display and
Volume” on page 13.
Go to the Setup tab to select the image source, type of projection,
video AGC (Automatic Gain Control), video format and to adjust
frequency, tracking and the image position. See “Setting Up the
Image Source” on page 14.
7. Run your presentation from your computer or video source.
8
V600UserGuide.book Page 9 Tuesday, March 21, 2000 8:26 AM
Using the Remote Control and Keypad
The remote control and projector keypad perform similar operations,
with one exception-the remote control has a volume control.
Menu
Power
Power—turns the projector
on and off
Menu—displays the menus
on the projected image
Enter
Next
Adjust
Enter—selects an option
button
Next—highlights the next
feature in the menu
POWER
MENU
ADJUST
ENTER
NEXT
Volume
Remote Control
(Optional with
V600)
Adjust—navigates between
tabs; moves a highlighted slider
bar left or right; and moves
between options for features
like Source and Projection
Keypad
Volume—increases or decreases volume
Press and hold the buttons to make repeated moves and adjustments.
9
English
Using the Remote Control and Keypad
V600UserGuide.book Page 10 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Positioning the Projector
The projector should be at least 2.5 feet (.9 m) from the screen but no
more than 32 feet (10 m) away from the screen.
V600 screen sizes are:
Distance
Width x Height
Diagonal
3’ (.9 m)
18 x 13" (.5 x .3 m)
22.5" (.6 m)
5’ (1.5 m)
31 x 23" (.8 x .6 m)
38.5" (1.0 m)
6.5’ (2.0 m)
40 x 30" (1.0 x .8 m)
50" (1.3 m)
8’ (2.4 m)
48 x 36" (1.21 x .9 m)
60" (1.5 m)
9’ (2.8 m)
56 x 42" (1.4 x 1.1 m)
70" (1.8 m)
10.5’ (3.2 m)
64 x 48" (1.6 x 1.21m)
80" (2.0 m)
12’ (3.6 m)
72 x 54" (1.8 x 1.4 m)
90" (2.3 m)
13’ (4.0 m)
80 x 60" (2.0 x 1.5m)
100" (2.5 m)
14.5’ (4.4 m)
88 x 66" (2.2 x 1.7 m)
110" (2.8 m)
16’ (4.8 m)
96 x 72" (2.4 x 1.8m)
120" (3.0 m)
17’ (5.2 m)
104 x 78" (2.6 x 2.0 m) 130" (3.3 m)
18’ (5.6 m)
112 x 84" (2.8 x 2.1m)
20’ (6.0 m)
120 x 90" (3.0 x 2.3 m) 150" (3.8 m)
33’ (10 m)
200 x 150" (5 x 3.8 m)
10
140" (3.6 m)
250" (6.4 m)
V600UserGuide.book Page 11 Tuesday, March 21, 2000 8:26 AM
Positioning the Projector
V600 Zoom screen sizes are:
Width x Height
Diagonal
3’ (.9 m)
13~17" x 10~13"
(.33~.43 x .25~.33 m)
16~21" (.4~.5 m)
5’ (1.5 m)
22~28"x 16~19"
(.55~.71 x .41~.48 m)
27~35" (.7~.9 m)
6.5’ (2.0 m)
29~38"x 22~28"
(.74~.97 x .56~.71 m)
36~47" (.9~1.2 m)
8’ (2.4 m)
34~46"x 26~32"
(.86~1.2 x .66~.81 m)
43~57" (1.1~1.5 m)
9’ (2.8 m)
41~54"x 31~40"
(1.0~1.4 x .79~1.0 m)
51~67" (1.3~1.7 m)
10.5’ (3.2 m)
46~61"x 35~46"
(1.2~1.5 x .89~1.2 m)
58~76" (1.5~ 1.9m)
12’ (3.6 m)
53~69"x 40~52"
(1.3~1.8 x 1.0~1.3 m)
66~86" (1.7~2.2 m)
13’ (4.0 m)
58~76" x 44~57"
(1.5~1.9 x 1.1~ 1.4m)
73~95" (1.9~2.4 m)
14.5’ (4.4 m)
64~84" x 48~62"
(1.6~2.1 x 1.2~1.6 m)
80~105" (2.0~2.7 m)
16’ (4.8 m)
70~91" x 53~69"
(1.8~2.3 x 1.4~1.8 m)
88~115" (2.2~3.0 m)
17’ (5.2 m)
74~99" x 57~74"
(1.8~2.5 x 1.4~1.9m)
95~124" (2.4~3.1 m)
18’ (5.6 m)
82~107" x 88~114"
(2.0~ 2.7 x 2.2~2.9 m)
103"~134" (2.6~3.4 m)
20’ (6.0 m)
88~114" x 66 ~86"
(2.2~2.9 x 1.7~2.1m)
110~143" (2.8~3.6 m)
33’ (10 m)
147~192" x 110~144"
(3.7~4.9 x 2.8~3.7 m)
184~240" (4.7~6.1 m)
English
Distance
11
V600UserGuide.book Page 12 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Using KODAK Image Manager
With one click, Kodak’s exclusive Image Manager lets you choose
the best image settings for your presentation type.
Important:The KODAK Image Manager settings work best if you
select Reset from the Adjust tab each time before selecting
an Image Manager setting.
1. Press Menu and use the Adjust + - buttons to move to the Kodak tab.
2. Press Next to move to the appropriate Image Manager feature.
3. Press Enter to select that feature.
4. Press Menu to dismiss the menu or wait for the menu to close
(about 15 seconds).
Photos (PC) matches the higher contrast found on a standard PC
monitor. This feature is best for:
• images created on a PC
• images from a KODAK digital camera
• a starting point for video input.
Photos (MAC) matches the lower contrast found on a standard
MACINTOSH monitor. It is generally used for images created on or
for a MACINTOSH. This setting also works well with a PC if you are
using higher than normal contrast PC images.
Rich Colors results in an image with deep contrast and saturated
vibrant colors. It is generally used under bright lighting conditions.
This setting works well to enhance colors of certain graphics and it
may be useful when images created for a MACINTOSH are displayed
from a PC.
Spreadsheets results in an image with contrast between a PC and
MACINTOSH monitor. It is generally used for text-rich tables, such
as financial displays. This setting factors in ambient light, subject
matter, and personal preferences to deliver the right balance of
contrast and brightness.
Graphics delivers the high contrast needed to project graphics and
text against solid colored backgrounds.
12
V600UserGuide.book Page 13 Tuesday, March 21, 2000 8:26 AM
Adjusting the Display and Volume
Adjusting the Display and Volume
English
The features available on the Adjust tab depend on your image
source.
Computer Source
Video source
Note: We recommend using the KODAK Image Manager to optimize
the display. Then, if further adjustments are needed, use the
brightness and contrast settings on the Adjust tab.
1. Press Menu and use the Adjust + - buttons to move to the Adjust tab.
2. Use the Next button to move to the feature that you want to
adjust.
3. Use the Adjust + - buttons to move the slider bars.
If you wish to return to the factory default settings, use Next to
highlight Reset and press Enter.
Note: The volume can also be adjusted from the remote control.
Brightness controls the intensity of the image.
Contrast controls the degree of difference between the lightest and
darkest parts of the image.
Color controls the saturation of the colors.
Tint controls the red-green color balance.
13
V600UserGuide.book Page 14 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Setting Up the Image Source
The features that are available on the Setup tab depend on the type of
image source that you are using.
Computer Source
Video Source
1. Press Menu and use the Adjust + - buttons to go to the Setup tab.
2. Use the Next button to select a feature.
3. Use the Adjust + - buttons to select an option for the selected
feature.
If you wish to return to the factory default settings, use Next to
highlight Reset and press Enter.
Source options are computer, video and S-video. When you change
sources, a source status message appears indicating if the projector is
receiving a signal from that source.
Signal is received:
No signal:
14
V600UserGuide.book Page 15 Tuesday, March 21, 2000 8:26 AM
Setting Up the Image Source
Projection options are front, rear and ceiling.
Front projection is used for projecting straight ahead
onto a screen.
• Rear projection reverses the image if you wish to project
from behind the screen.
• Use ceiling projection when you attach the projector to a
permanent ceiling bracket. (To purchase the optional
ceiling mount kit go to our Web site at
www.kodak.com/go/projectors.)
H Position and V Position adjustments are available only for images
from a computer.
Adjust Frequency and Tracking of images from a computer until the
image is evenly spaced, fuzzy vertical lines disappear, or the
projected image is as wide as the menu.
Video Format refers to the height and width ratio of the projected
image. The 4:3 ratio is the standard format. Use the 16:9 ratio when
projecting wide screen (anamorph) movies in 16:9 format.
We recommend leaving AGC (Automatic Gain Control) turned on.
When it is turned on, the image is automatically adjusted if the video
signal is too strong or too weak.
15
English
•
V600UserGuide.book Page 16 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Selecting a Language
The on-screen menus can be displayed in seven languages.
1. Press Menu and use the Adjust + - buttons to go to the Language
tab.
2. Press Next to highlight the desired language.
3. Press Enter to select the language.
16
V600UserGuide.book Page 17 Tuesday, March 21, 2000 8:26 AM
Checking the Status
Checking the Status
English
The information displayed on the Status tab depends on the type of
image source you use.
Computer Source
Video Source
The Reset Lamp Hours feature is the only item that can be adjusted
on this screen. Refer to the Lamp Hours Used when you want to
know how much longer your lamp will last. Estimated lamp life
expectancy is 2,000 to 4,000 hours.
Important:Only reset the lamp hours after you have installed a new
lamp.
To reset lamp hours
1. Press Menu and use the Adjust + - buttons to go to the Status tab.
2. Press Next to highlight Reset Lamp Hours.
3. Press Enter.
The Lamp Hours Used number resets to zero.
17
V600UserGuide.book Page 18 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Turning Off the Projector
Turn off the projector and image sources in the order listed here.
Note: You might not be using all of these components for your
presentation.
•
•
•
Computer
Projector
Audio source if different from your video source or
computer
• Video source such as VCR, DVD or digital camera.
To turn off the projector:
1. Press the Power button on the keypad or remote control.
A confirmation screen appears.
2. Press the Power button again to confirm.
The lamp turns off immediately but the fan continues to run until
the projector cools down.
The Power light continues to blink after the projector has cooled
and as long as the live power cord is connected to the projector.
18
V600UserGuide.book Page 19 Tuesday, March 21, 2000 8:26 AM
Transporting the Projector
When you place the projector in the carrying case make sure the lens
is positioned inside the lens notch of the foam insert. Secure the
projector with the velcro strap.
velcro strap
lens notch
foam insert
velcro strap
Important:The carrying case provided with the projector is not
designed to be checked through baggage. If you can not
hand carry this projector make sure it is packed properly to
prevent damage. The warranty does not cover damage
from improper handling.
A hard-sided case is available as an option. To purchase accessories,
go to our Web site at www.kodak.com/go/projectors.
19
English
Transporting the Projector
V600UserGuide.book Page 20 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Maintenance
Changing the Lamp Module
Important:The lamp in the KODAK V600 Digital Projector and the
KODAK V600 Zoom Digital Projector contains trace
amounts of mercury. Some governments require special
disposal of lamps containing mercury. Dispose of lamps in
accordance with the law and any applicable local
regulations.
The lamp module should be replaced with a certified replacement
part. To order a new lamp, contact your local dealer of KODAK
products or visit our Web site at www.kodak.com/go/projectors
After you have changed the lamp module, make sure that you reset
the lamp counter. See “To reset lamp hours” on page 17.
Warning: When replacing the lamp, be sure to turn off the power and
unplug the power cord. To avoid burns, wait 30 minutes before
opening the lamp module door.
Warning: When you open the lamp module door, be careful to not
touch the hot surfaces inside.
Warning: Do not loosen or remove any screws other than those on
the lamp module door and the lamp module. Doing so may result in
electric shock.
To replace the lamp module:
1. Turn off the projector and let the projector cool for at least 30
minutes.
The fan continues to run after the projector has been turned off.
2. Unplug the power cord from the projector.
3. Turn the projector upside down. With a flat head screw driver,
loosen but do not remove the slotted screw in the lamp module
door.
20
V600UserGuide.book Page 21 Tuesday, March 21, 2000 8:26 AM
Maintenance
English
4. Lift up on the screw side of the lamp module door. Then
carefully remove the lamp module cover.
5. Loosen the two slotted screws on the lamp module bracket.
6. Gently lift and pull up on the metal wire to remove the lamp
module.
&DXWLRQ 'RQRWWRXFKWKHJODVVSRUWLRQRIWKHQHZODPSPRGXOH
ZLWK\RXUKDQGVRUDOORZLWWRWRXFKRWKHUREMHFWVDVWKLV
PD\GDPDJHLWDQGVKRUWHQLWVRSHUDWLRQDOOLIH
&DXWLRQ 'RQRWGURSWKHODPSPRGXOHDVWKHJODVVPD\VKDWWHU
DQGFDXVHLQMXU\
21
V600UserGuide.book Page 22 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
7. Carefully place the new lamp module into the projector, with the
glass portion facing left. Make sure that it is inserted securely and
that the two holes match the two pins of the inner engine case.
Tighten the slotted screws.
8. Replace the lamp module door and tighten the screw.
9. Reset the lamp usage counter. See “To reset lamp hours” on
page 17.
Important:The only time that you should reset the counter is after you
have replaced the lamp module.
Cleaning the Projection Lens
1. Turn off the projector and allow it to cool.
2. Remove the lens cap.
3. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
&DXWLRQ $YRLGXVLQJDQH[FHVVLYHDPRXQWRIFDPHUDOHQVFOHDQHU
'RQRWXVHDEUDVLYHFOHDQHUVVROYHQWVRURWKHUKDUVK
FKHPLFDOVDVWKH\PLJKWVFUDWFKWKHOHQV'RQRWVSLOO
DQ\FDPHUDOHQVFOHDQHURQWKHH[WHULRUFDVHDVLWPD\
IDGHGHIRUPRUPHOWWKHH[WHULRUFDVH
4. Lightly wipe the cleaning cloth over the lens.
5. If you do not intend to use the projector immediately, replace the
lens cap.
Cleaning the Exterior Case
1. Turn off the projector and allow it to cool.
2. To remove dirt or dust, gently wipe the exterior case with a soft,
dry, lint-free cloth.
3. To remove stubborn dirt or stains, moisten a soft cloth with water
and a neutral detergent and gently wipe the exterior case.
&DXWLRQ 'RQRWXVHDOFRKROEHQ]HQHWKLQQHURURWKHUFKHPLFDO
FOHDQHUVZKLFKPD\IDGHGHIRUPRUPHOWWKHH[WHULRU
FDVH'RQRWDSSO\WKHGHWHUJHQWVROXWLRQWRWKH
SURMHFWRUOHQVDVLWPD\VFUDWFKWKHOHQV
22
V600UserGuide.book Page 23 Tuesday, March 21, 2000 8:26 AM
Maintenance
To ensure proper ventilation inside your multimedia projector, the air
filter should be periodically cleaned. More frequent cleaning may be
required if you use your projector in a dusty or dirty environment.
&DXWLRQ ,IWKHDLUILOWHULVQRWFOHDQHGSHULRGLFDOO\LWFDQEHFRPH
FORJJHGZLWKGXVWDQGSUHYHQWSURSHUYHQWLODWLRQ7KLV
PD\FDXVHRYHUKHDWLQJDQGGDPDJH
Important:If the filter cannot be cleaned or becomes damaged or
torn, it should be promptly replaced with an certified
KODAK replacement part. Contact your dealer of KODAK
products for additional information or visit our Web site at
www.kodak.com/go/projectors
1. Turn off the projector and wait for the fan to stop running.
2. Unplug the projector.
3. Turn the projector on its side so that the connection panel is
facing upwards.
Note: Standing the projector on its side keeps dust from getting
inside.
4. Locate the air filter cover on the bottom of the projector and slide
the cover latch downward to remove the cover.
The air filter is attached to the inside of the air filter cover.
5. Use a soft brush to clean the air filter being careful not to tear the
filter or loosen it.
&DXWLRQ ,QVWDOOLQJDZHWRUGDPSDLUILOWHUPD\GDPDJH\RXU
SURMHFWRU
6. Replace the air filter cover on the projector. Make sure that it
clicks into place.
&DXWLRQ 1HYHUUHSODFHWKHDLUILOWHUFRYHUZLWKRXWWKHDLUILOWHU
DWWDFKHGWKLVDOORZVGXVWWRJHWLQVLGH1HYHURSHUDWH
\RXUSURMHFWRUZLWKRXWWKHDLUILOWHUFRYHULQSODFH
'RLQJVRPD\GDPDJH\RXUSURMHFWRU
23
English
Cleaning the Air Filter
V600UserGuide.book Page 24 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Troubleshooting
If you don’t find the answer to your problem here, visit our Web site
at www.kodak.com/go/projectors for the latest updates on
troubleshooting.
Power Indicator
The power indicator on the keypad provides you with information
about the condition of the projector.
Light Status
24
Condition
Blinking
Lamp is off but live power cord is
connected to the projector.
Projector is in standby mode.
OR
Lamp is off and fan is running.
Projector is cooling down.
Steady
Lamp is on and fan is running.
Projector is ready.
Two blinks
Scaling chip is malfunctioning.
Call KIC-D at 800-23kodak.
Three blinks
RAM is malfunctioning.
Call KIC-D at 800-23kodak.
Four blinks
I2C bus is malfunctioning.
Call KIC-D at 800-23kodak.
Five blinks
Lamp is malfunctioning.
Call KIC-D at 800-23kodak.
Six blinks
Fan is malfunctioning.
Call KIC-D at 800-23kodak.
V600UserGuide.book Page 25 Tuesday, March 21, 2000 8:26 AM
Troubleshooting
Problem
Solution
Color or text is not being
projected.
Adjust the brightness up or down until
the text is visible.
Some text or fonts are not
sharp with a computer as an
image source.
For optimal results, set the computer’s
resolution to 800 x 600. (Refer to your
computer user manual.) But this projector
can compress resolutions up to
1024 x 768.
Image isn't centered on the
screen.
• Be sure that the projector is at a 90°
angle to the screen.
• Reposition the image. See “Setting Up
the Image Source” on page 14.
Image is out of focus.
• Turn the projection lens to focus the
image.
• Make sure that the projection screen is
at least 3 ft (.9 m) from the projector.
• Check the projection lens to see if it
needs cleaning.
Image and menus are upside • If projecting from a ceiling mount,
down.
make sure that Ceiling Projection is
selected on the Setup tab in the Menu.
• If projecting from an upright position,
make sure that Front or Rear projection
is selected on the Setup tab in the
Menu.
Image and menus are
reversed from left to right.
• If projecting from behind a screen
make sure that Rear Projection is
selected on the Setup tab in the Menu.
• If projecting in front of a screen, make
sure that Front or Ceiling Projection is
selected on the Setup tab in the Menu.
25
English
Image Quality
V600UserGuide.book Page 26 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Problem
Image appears flat with no
contrast
Solution
To adjust the contrast:
1.Press Menu and use the Adjust + buttons to go to the Adjust tab.
2.Use the Next button to highlight
Contrast.
3.Use the Adjust + - buttons to
increase or decrease the contrast.
Image appears washed out or • Check the projection lens to see if it
dark.
needs cleaning.
• To adjust the brightness:
1.Press Menu and use the Adjust + buttons to go to the Adjust tab.
2.Use the Next button to highlight
Brightness.
3.Use the Adjust + - buttons to
increase or decrease the brightness.
Image is "noisy" or streaked. • From the Setup tab in the menus, adjust
the frequency and tracking manually to
find an optimal setting.
• Try connecting to another computer.
The problem could be with your
computer's video card.
26
Image is wider at the top or
bottom of the screen.
This keystoning effect is caused by the
projection angle not being perpendicular
to the screen. For a more pleasing image
result, raise or lower the front legs or
prop up the back of the projector.
Image is wider at one side
than the other
Make sure the projector is at a 90 degree
angle to the screen.
V600UserGuide.book Page 27 Tuesday, March 21, 2000 8:26 AM
Troubleshooting
Solution
Projected colors don’t match Use the KODAK Image Manager to
the computer or video source select a setting that is more acceptable.
colors.
Important: The KODAK Image Manager
settings work best if you select
Reset from the Adjust Tab each
time before selecting an Image
Manager setting.
If further adjustment is needed, optimize
the brightness, tint, color and contrast
from the Adjust tab in the Menus.
27
English
Problem
V600UserGuide.book Page 28 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Sound
Problem
Cause and Solution
No sound.
• Adjust volume.
• Verify audio / input connections.
• Adjust audio source.
Poor sound quality.
• Make sure you are connected to the
earphone jack on your laptop or line out
jack on your desktop.
• Make sure the volume setting on your
computer is halfway.
No audio-out port on the
image source.
You are not able to connect audio to the
projector.
Remote Control
Problem
Projector responds poorly
or not at all to the remote
control.
28
Cause and Solution
• Make sure that the total distance from
the remote to the projector is no more
than 32 feet (10 m).
• Point the remote control at the screen or
at the front of the projector.
• Make sure nothing is blocking the
infrared sensor on the front of the
projector.
• Darken the room. The lighting might be
effecting the remote control.
• Replace the remote control batteries.
V600UserGuide.book Page 29 Tuesday, March 21, 2000 8:26 AM
Troubleshooting
Problem
Cause and Solution
No light is coming from the • Make sure that the power cord is
lamp.
properly connected to a fully functional
AC electric outlet. The Power light
blinks when the power is connected but
the projector is not turned on. The
Power light is a steady green when the
lamp is running.
• Make sure that the power cord is
properly connected to the projector.
• Make sure that you have removed the
lens cap on the projector lens at the front
of the projector.
• Make sure you have pressed the Power
button and the Power light is a steady
green.
• Check the projector's lamp to make sure
that it is securely connected in the lamp
module.
• Make sure that the lamp module door is
fully closed.
• Make sure that the cable connectors do
not have any bent pins.
• Replace the lamp.
Lamp shuts off.
• A minor power surge may cause the
lamp to shut off. Press the Power button
twice to turn off the projector. (The
Power light continues to blink and the
fan continues to run until the projector
cools down.) Wait at least three minutes,
then press the Power button again.
• Replace the lamp module.
29
English
Lamp
V600UserGuide.book Page 30 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Image Source
Problem
30
Cause and Solution
The S-Video image source
does not appear.
Some inexpensive cables are not
compatible with the projector. Be sure to
use the cable that came with your
projector.
Only the start-up screen
appears and not the image
from the image source.
• Verify that the cables are connected
correctly. See “Connecting the
Projector” on page 6.
• Verify that the proper image source is
connected and that it is selected on the
Setup tab of the menus.
• Make sure that the image source is
turned on.
• Turn off everything and power up again
in the proper order. See “Turning Off the
Projector” on page 18. See “Starting the
Presentation” on page 7.
• Make sure that your laptop's external
video port is turned on. See the
computer manual for details.
V600UserGuide.book Page 31 Tuesday, March 21, 2000 8:26 AM
Troubleshooting
The image source is
connected but a No Signal
message appears.
Cause and Solution
• Verify that the cables are connected
correctly. See “Connecting the
Projector” on page 6.
• Verify that the proper image source is
connected and that it is selected on the
Setup tab of the menus.
• Make sure there are no bent pins in the
connectors.
• Make sure the image source is turned
on.
• Turn off everything and power up again
in the proper order. See “Turning Off the
Projector” on page 18. See “Starting the
Presentation” on page 7.
• Make sure that your laptop's external
video port is turned on. See the
computer manual for details.
MFG Mode screen appears Turn off the projector and wait until the
instead of the image.
fan stops. Turn on the projector.
Note: The MFG mode screen appears if
you press the Power button at the
same time that you plug in the power
cord. This mode should only be used
by service technicians.
31
English
Problem
V600UserGuide.book Page 32 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Safety
These safety precautions include information to prevent personal
injury and damage to the projector.
Safety Definitions
Warning: Statements identify conditions or practices that could
result in personal injury.
Caution: Statements identify conditions or practices that could result
in damage to your equipment.
Warning: For information about use of a feature, please refer
to this User Guide.
Warning: Hot surface. Do not touch.
Projector Safety
Warning: To replace the lamp, turn off the power and unplug
the power cord. To avoid burns, wait 30 minutes before opening
the lamp door. Follow all instructions provided in this User
Guide. See “Changing the Lamp Module” on page 20.
Warning: When you open the lamp module door, be careful not
to touch the hot surfaces inside.
Warning: Please use the power cord provided. Connect the power
cord to a receptacle with a protective safety (earth) ground terminal.
Warning: Don’t look directly into the lens when the lamp is on.
Doing so may cause eye injury.
Warning: Servicing your own projector may expose you to hazards
or create potential hazards. Also, servicing your own projector will
void the warranty. Refer all service to qualified service personnel. See
“If You Need Assistance” on page 2.
Warning: In the unlikely event of the bulb rupturing, thoroughly
clean the area behind the projector and discard any food that might
have been contaminated with broken glass.
Warning: Do not loosen or remove any screws other than those on
the lamp module door and the lamp module. Doing so may result in
electric shock.
Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
Caution: Don’t put the projector on a hot surface or in direct sunlight.
Caution: Do not drop the projector.
32
V600UserGuide.book Page 33 Tuesday, March 21, 2000 8:26 AM
Caution: Never operate your projector without the lamp module or
lamp module door. Doing so may damage the projector.
Caution: Proper ventilation is important. Don’t block ventilation
openings. Never operate this projector in an enclosed area. Do not
place the projector on a tablecloth or other soft covering that may
block the vents. With ceiling installations, use approved mounting
hardware. Do not put the projector near heat ducts, air cleaners,
transformers or other electrical devices. For permanent installations
follow local codes.
Caution: Do not touch the glass portion of the new lamp module
with your hands or allow it to touch other objects as this may damage
it and shorten its operational life.
Caution: Do not drop the lamp module as the glass may shatter.
Battery Safety
•
•
•
•
•
•
•
•
•
•
•
Read and follow all warnings and instructions supplied by
the battery manufacturer.
Keep batteries away from children.
Store batteries in their original packaging.
When inserting batteries, verify that the (+) and (-) terminals
are aligned correctly.
Replace all batteries of a set at the same time.
Do not mix new batteries with used ones.
Do not use batteries of different chemistries, capacities,
brands or sizes together. Leakage could result.
Do not disassemble, recharge, or short-circuit batteries.
Do not subject batteries to high temperature or fire.
Discard used batteries according to all applicable local and
national regulations.
In the unlikely event of contact with battery electrolyte,
customers in the U.S. can contact the Kodak Information
Center (KIC) at 1-800-242-2424. U.S. customers can also
contact KIC for information regarding electrolyte removal
from KODAK product components. Customers outside the
U.S. can contact their local Kodak Customer Service
representative.
33
English
Safety
V600UserGuide.book Page 34 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Specifications
Specification
V600
V600 Zoom
Weight in lbs. (kg)
7.5 (3.4)
7.6 (3.4)
Dimensions (inches)
(WxDxH)
12.8 x 9.8 x 3.6
(with lens)
12.8 x 10.8 x 3.6
(with lens)
Dimensions (mm)
(WxDxH)
325 x 250 x 92
(with lens)
325 x 275 x 92
(with lens)
Color Palette
16.7 million (24 bit) 16.7 million (24 bit)
Resolution
800 x 600
800 x 600
XGA compression
(1024 x 768)
Yes
Yes
Three 0.9” panel
polysilicone LCD
Yes
Yes
Projection lamp
120w UHP, ultra
compact
120w UHP, ultra
compact
Lamp life
Up to 4000 hours
Up to 4000 hours
User-replaceable lamp
Yes
Yes
Brightness (ANSI lumens - 800
based on industry
specification practices)
800
Contrast ratio
(Full On/Off)
200:1
34
200:1
V600UserGuide.book Page 35 Tuesday, March 21, 2000 8:26 AM
Specifications
Projection Distances/
Image Sizes
V600
0.9 m (2.95 ft)
0.57 m (1.875 ft)
3.66 m (12 ft)
2.29 m (7.5 ft)
10 m (32.8 ft)
6.35 m (20.6 ft)
V600 Zoom
0.9 m (2.95 ft)
0.4 m (1.33 ft) to 0.53 m
(1.74 ft)
3.66 m (12 ft)
1.68 m (5.5 ft) to 2.19 m
(7.17 ft)
10 m (32.8 ft)
4.67 m (15.3ft) to 6.1 m
(20 ft)
Projection Lens
Fixed/manual focus
Manual zoom/focus
Zoom Factor
N/A
1.3x
Keystone Correction
10 degrees
10 degrees
Aspect Ratio
4:3, 16:9
4:3, 16:9
Audio (built in)
Stereo, 2 x 2 watts
Stereo, 2 x 2 watts
Video Compatibility –
Yes
NTSC/NTSC 4.43
PAL B/D/G/H/I/K/L/N/M
SECAM B/D/G/H/K/L
Yes
Computer compatibility
VGA/SVGA/XGA/
SXGA
VGA/SVGA/XGA/
SXGA
Vertical frequency (Hz)
56 – 85
56 – 85
Horizontal frequency
(KHz)
30 – 90
30 – 90
MACINTOSH
Compatibility
Yes
Yes
Audible noise – typical
42 measured
42 measured
35
English
Specification
V600UserGuide.book Page 36 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
Specification
V600
V600 Zoom
Connections on projector
Analog RGB (15 Pin HD) Yes
Yes
Composite video (RCA)
Yes
Yes
Stereo Audio (1/8” mini- Yes
plug)
Yes
S-video
Yes
Yes
Voltage (AC RMS)
100 - 240
100 - 240
Frequency (Hz)
50 – 60
50 – 60
Auto Sense
Yes
Yes
Typical Power
Consumption (watts)
195
195
Operating Temperature
Range
0 – 35 degrees C
0 – 35 degrees C
Storage Temperature
Range
-20 – 70 degrees C
-20 – 70 degrees C
Power Supply
Humidity Range (relative) 10 – 95%
10 – 95%
Altitude (operating)
0 – 10,000 ft
0 – 3,048 m
0 – 10,000 ft
0 – 3,048 m
Altitude (storage)
0 – 40,000 ft.
0 – 12,192 m
0 – 40,000 ft
0 – 12,192 m
36
V600UserGuide.book Page 37 Tuesday, March 21, 2000 8:26 AM
Warranty
WARRANTY TIME PERIOD
English
Kodak warrants the KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
(excluding lamps, which have an initial 90-day warranty from the date of purchase) to be free from
malfunctions and defects in both materials and workmanship for two years from the date of purchase.
WARRANTY REPAIR COVERAGE
This warranty will be honored within the geographical location that the product was purchased.
If the equipment does not function properly during the warranty period due to defects in either materials or
workmanship, Kodak will, at its option, either repair or replace the equipment without charge, subject to
the conditions and limitations stated herein. Such repair will include all labor as well as any necessary
adjustments and/or replacement parts.
If replacement parts are used in making repairs, these parts may be remanufactured, or may contain
remanufactured materials. If it is necessary to replace the entire system, it may be replaced with a
remanufactured system.
Kodak will also provide telephone assistance during the warranty period.
LIMITATIONS
WARRANTY SERVICE WILL NOT BE PROVIDED WITHOUT DATED PROOF OF PURCHASE.
THIS WARRANTY BECOMES NULL AND VOID IF YOU FAIL TO PACK YOUR DIGITAL
PROJECTOR IN A MANNER CONSISTENT WITH THE ORIGINAL PRODUCT PACKAGING AND
DAMAGE OCCURS DURING PRODUCT SHIPMENT.
THIS WARRANTY DOES NOT COVER: CIRCUMSTANCES BEYOND KODAK’S CONTROL;
SERVICES OR PARTS TO CORRECT PROBLEMS RESULTING FROM THE USE OF
ATTACHMENTS, ACCESSORIES, OR ALTERATIONS NOT MARKETED BY KODAK; SERVICE
REQUIRED AS THE RESULT OF UNAUTHORIZED MODIFICATIONS OR SERVICE; MISUSE,
ABUSE; FAILURE TO FOLLOW KODAK’S OPERATING, MAINTENANCE, OR REPACKAGING
INSTRUCTIONS; OR FAILURE TO USE ITEMS SUPPLIED BY KODAK (SUCH AS ADAPTORS
AND CABLES).
KODAK MAKES NO OTHER WARRANTIES, EXPRESS, IMPLIED, OR OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE FOR THIS EQUIPMENT OR SOFTWARE.
REPAIR OR REPLACEMENT WITHOUT CHARGE ARE KODAK’S ONLY OBLIGATION UNDER
THIS WARRANTY. KODAK WILL NOT BE RESPONSIBLE FOR ANY SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE PURCHASE, USE, OR
IMPROPER FUNCTIONING OF THIS EQUIPMENT REGARDLESS OF THE CAUSE. SUCH
DAMAGES FOR WHICH KODAK WILL NOT BE RESPONSIBLE INCLUDE, BUT ARE NOT
LIMITED TO, LOSS OF REVENUE OR PROFIT, DOWNTIME COSTS, LOSS OF USE OF THE
EQUIPMENT, COST OF ANY SUBSTITUTE EQUIPMENT, FACILITIES OR SERVICES, OR
CLAIMS OF YOUR CUSTOMERS FOR SUCH DAMAGES.
Depending on your geographical location, some limitations and exclusions may not apply.
Shipment of a unit from the customer to the KODAK Service Center will be at the customer’s expense.
This warranty is not transferable from the original purchaser of the equipment.
37
V600UserGuide.book Page 38 Tuesday, March 21, 2000 8:26 AM
KODAK V600 Digital Projector and KODAK V600 Zoom Digital Projector
HOW TO OBTAIN SERVICE
Please refer to the Service and Support section of your User’s Guide for the support hotline designated to
your location.
When returning a digital projector for repair, the unit shall be packed in its original packing materials. A
problem report should also be enclosed with the equipment. If the original packaging has been discarded or
is not available, packing will be at the owner’s expense.
The repaired or replaced unit will be shipped from Kodak within five business days from the date of the
digital projector receipt at the service center.
Unless a specific Kodak warranty is communicated to the purchaser in writing by a Kodak company, no
other warranty or liability exists beyond the information contained above, even though defect, damage, or
loss may be caused by negligence or other act.
To obtain warranty repair service contact your local Kodak representative. For assistance, refer to the
Service and Support information in the KODAK Digital Projector User’s Guide.
38
V600UserGuide.book Page 39 Tuesday, March 21, 2000 8:26 AM
V600UserGuide.book Page 40 Tuesday, March 21, 2000 8:26 AM
Eastman Kodak Company
343 State Street
Rochester, New York 14650
Kodak is a trademark of
Eastman Kodak Company.
PN 692934
3/2000
©Eastman Kodak Company, 2000
Printed in Taiwan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising