User manual | Keysight Technologies FieldFox Handheld Analyzers

Keysight Technologies
FieldFox Handheld Analyzers
4/6.5/9/14/18/26.5/32/44/50 GHz
Technical Overview
N9913A
N9914A
N9915A
N9916A
N9917A
N9918A
N9950A
N9951A
N9952A
N9925A
N9926A
N9927A
N9928A
N9935A
N9936A
N9937A
N9938A
N9960A
N9961A
N9962A
02 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Carry Precision with You
Measuring up and earning a spot in your ield kit is the driving idea behind Keysight’s
FieldFox handheld analyzers. They’re equipped to handle routine maintenance, in-depth
troubleshooting and anything in between. Better yet, FieldFox delivers precise microwave and millimeter-wave measurements — wherever you need to go.
Why choose FieldFox?
– Measure with conidence — precise measurements agree with benchtop results
– Withstands your toughest working environments — rugged enough to meet MIL-specs
– Weighs less than alternative solutions — 7.1 lb (3.2 kg)
– Offers budget lexibility — choose capabilities you need today and easily upgrade later
RF and microwave
(combination) analyzers
Microwave vector
network analyzers
Microwave spectrum
analyzers
Base: Cable and antenna analyzer
Base: Transmission/reflection
vector network analyzer (VNA)
Base: Spectrum analyzer
Key options:
– Spectrum analyzer
– Vector network analyzer
– Built-in power meter
– Pulse measurement
Key options:
– Built-in power meter
– Pulse measurement
Key options:
– Built-in power meter
– Pulse measurements
03 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Leverage our Legacy of Measurement Leadership
With FieldFox, you’re carrying the
precision of our industry-standard
benchtop analyzers. By delivering levels
of consistency not available in any other
handhelds, FieldFox ensures conidence in
your results.
FieldFox industry innovations
Inside, we leveraged well-tested algorithms from Keysight’s high-performance
VNAs. To lighten your load, we simpliied
calibration by adding built-in standards
and eliminating the need to carry calibration kits.
Vector network analyzer
Dynamic range up to 100 dB
2012
FieldFox handheld microwave
analyzer
2008
FieldFox handheld RF analyzer
2009
PXA X-Series signal analyzer
2007
PNA-X vector network analyzer
2001
PSA spectrum analyzer
2000
PNA vector network analyzer
1984
8510A vector network analyzer
1978
HP 8566B spectrum analyzer
First 50 GHz handheld microwave analyzer
Cable and antenna analyzer
DTF and TDR in a single sweep
Spectrum analyzer
Absolute amplitude accuracy ± 0.5 dB
To enhance spectrum analysis, FieldFox
includes the same PowerSuite measurements used in Keysight signal analyzers,
enabling fast, accurate, one-button
characterization of channelized communication systems. The InstAlign capability
lets you instantly make accurate power
measurements in the ield, even when
temperature luctuates.
2015
FieldFox 50 GHz handheld
microwave analyzer
“FieldFox’s result is almost identical to my PNA.
I want one of these for all of my engineers.”
– Senior calibration engineer from spacecraft research and development center.
04 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Increase System Uptime and Reduce Mission Risk
Install and maintain cellular systems with the cable and antenna
(CAT) tester
– Ensure communication continuity with all the essential measurements needed to
troubleshoot and maintain microwave links
– Always be at the ready with an instrument display easily optimized for clear viewing
in direct sunlight or darkness
– Reduce measurement complexity and time-to-repair with quick and accurate line
sweeps in the ield without calibration kits
– Protect your investment by adding software license key upgrades as your needs
change
Photo courtesy of INTELSAT
– Increase your team’s preparedness in the harshest environments with a completely
sealed instrument rugged enough to meet MIL specs
Work better and faster in radar installation and maintenance (I&M)
– Improve your team’s eficiency with a single analyzer that provides network, spectrum,
and power measurements up through the Ka and Q bands
– Ensure your team’s readiness with an instrument rugged enough to meet
MIL-PRF-28800F Class 2 and IP53 specs
– Increase system uptime and reduce mission risk with fast and accurate characterization of cables, waveguides, and components
– Reduce your cost of ownership, with one instrument to purchase and maintain
Photo courtesy of INTELSAT
– Increase your conidence with system and component measurements that agree
with trusted Keysight/Agilent/HP benchtop instruments
Accelerate I&M work at satellite ground stations
– Validate system performance with fast, detailed analysis of up uplink and downlink
signals
– Quickly diagnose faults using built-in cable and antenna analysis, network analysis,
and power measurements
– Perform accurate frequency translation gain/loss measurements to verify upconverters and downconverters at the LRU level
– Depend on MIL-spec ruggedness and a completely sealed instrument, designed to
withstand harsh environments
Learn more about FieldFox applications and download resources at:
www.keysight.com/ind/ieldtest
Photo courtesy of INDRA S.A.
– Maintain cable, waveguide, and antenna systems consistently and eficiently with
calibrated VNA and CAT measurements
05 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Enhance Research and Education
Add the ultimate companion tool to every R&D bench
– Equip your lab with must-have measurements up to 50 GHz with the affordable
FieldFox
– Increase your conidence with measurements that agree with trusted Keysight/
Agilent/HP benchtop instruments
– Get unprecedented lexibility with the multi-function FieldFox
– Give your team measurement convenience with a portable form factor and battery
operation
– Free up high-performance benchtop instruments with FieldFox
Bring a new dimension to engineering classes and labs
– Optimize EE/ECE department budgets with as many as 10 instruments in one
– Buy what you need today, and add features via software license keys as your
curriculum changes
– Achieve maximum teaching eficiency with a portable instrument that is easy to
carry from class to lab and provides battery life of 3.5 hours
– Enhance student comprehension by remotely projecting, monitoring, and controlling
the instrument
– Reinforce theoretical concepts by easily demonstrating measured results
– Save time developing your curriculum with complimentary ready-made lesson plans
Learn more about FieldFox applications and download resources at:
www.keysight.com/ind/ieldtest
06 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Pick Up FieldFox for its Ergonomics
Portrait design and
large buttons for easy
operation – even
with gloves on
Convenient side
strap makes it easy
to hold and carry
Anti-glare 6.5 inch
LCD display with
LED backlight
11.5”
(292 mm)
Backlit keypad
Task-driven keys
are grouped to
easily perform ield
measurements
Dedicated marker
keys for quick marker
function access
7.4”
(188 mm)
07 | Keysight | FieldFox Handheld Analyzers – Technical Overview
… and Depend on Its Durability and Convenience
TOP
Type-N (f)
Port 1
3.5 mm (m)
2.4 mm (m)
Port 2
Connector bay protects
RF connectors
Get precise location using
the built-in GPS receiver
External reference and
external trigger input
Quick connect
shoulder strap clips
RIGHT SIDE
LAN port for data transfer
and SCPI programming
SD lash card for
data storage
Keep going with
ield-swappable
batteries that last
up to 3.5 hours
USB ports for easy
data storage and
SCPI programming1
External reference and
external trigger output
Gasketed doors protect
ports from moisture
LEFT SIDE
Built-in DC supply
for powering external
bias-tees, probes, and
active devices
1.
SCPI over USB available on N995xA and N996xA models only, not on other FieldFox models.
08 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Utilize the Industry’s Most Comprehensive Handheld Analyzers
Cable and antenna analyzer
– Distance-to-fault (DTF) and return loss/VSWR
– 1-port cable loss, 2-port insertion loss, and time-domain relectometry (TDR)
– Integrated QuickCal up to 18 GHz for simple ield measurements—
no calibration kit required
Spectrum analyzer
– Unprecedented amplitude accuracy of ± 0.5 dB with InstAlign 1—no warm-up
required
– Tracking generator, independent source, and preampliier covering the full
frequency range
– Channel power (CHP), occupied bandwidth (OBW), and interference analysis
Vector network analyzer
– All four S-parameters, magnitude and phase
– Time-domain analysis, mixed-mode relection S-parameters
– CalReady, QuickCal, full 2-port cal, TRL, waveguide cal, ECal support,
and a Guided Calibration Wizard
Built-in power meter
– Power measurements over a deined bandwidth, without an external sensor
– Easy to view analog and digital display
– ± 0.5 dB accuracy with InstAlign1
1.
With FieldFox InstAlign, internal amplitude alignments occur automatically as enviromental
conditions change, without any user intervention.
09 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Utilize the Industry’s Most Comprehensive Handheld Analyzers (continued)
Power measurements using a USB power sensor
– Accurate absolute power measurements at a CW frequency
– Swept-frequency power measurements
– Frequency-offset capability for converter test
Pulse measurements using a USB peak power sensor
– Peak power, average power and peak-to-average ratio measurements
– Pulse proile characterization
– Portable solution for radar pulse analysis
Vector voltmeter
– Cable trimming, phase shift, and electrical length measurements
– A/B and B/A ratio measurements
– Similar functionality to the HP 8508A VVM
Extended range transmission analysis (ERTA)
– Scalar insertion loss measurement of in-situ cables with long distances
between test ports
– InstAlign enables accurate microwave measurements with no warm-up
– Converter test using ERTA’s frequency-offset capability
10 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Choose the FieldFox that Meets Your Needs
1
Notes:
For more information on N9912A, see FieldFox N9912A RF Analyzer, Technical Overview (5989-8618EN)
For more information on N9923A, see FieldFox N9923A Vector Network Analyzer, Technical Overview (5990-5087EN)
1. Combination analyzer = Cable and antenna tester (CAT) + Vector network analyzer (VNA) + Spectrum analyzer (SA)
11 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Create the Right Coniguration for Your Application
Select the capabilities you need today and add more as needs change: features are ield-upgradeable and are added via software
licence keys. RF and microwave analyzers are referred to as combination analyzers in this section.
Feature
CAT/ vector network analysis
Cable and antenna analyzer
Combination analyzers
N9913/4/5/6/7/8A
N9950/1/2A
N9923A
N9925/6/7/8A
N9935/6/7/8A
N9960/1/2A
ü
ü
ü
ü
VSWR and relection
ü
VNA full 2-port S-parameters
–
1-port mixed-mode S-parameters
–
ü
ü
ü
QuickCal
TDR cable measurements
Vector voltmeter
Spectrum analysis
ü
–
1 port
Spectrum analyzer
ü
Extended range transmission analysis (ERTA)
–
Tracking generator
Pre-ampliier
Spectrum analyzers
N9912A
VNA transmission/relection
VNA time domain
Vector network analyzers
ü
ü
ü
ü
ü
1
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
–
ü
ü
ü
ü
ü
ü
ü
ü
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
ü
ü
ü
ü
Interference analyzer and spectrogram
ü
–
–
ü
–
Spectrum analyzer time gating
–
–
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
Power measurements
USB power sensor meas. versus frequency
USB power sensor support
Pulse meas. with USB peak power sensor
Built-in power meter
System features
Remote control capability
GPS receiver
DC bias variable-voltage source
ü
ü
ü
external
–
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
–
ü
ü
ü
ü
ü
external
–
ü
ü
ü
ü
Notes:
Some of the features listed here require an option. See page 22 for option information or see the FieldFox Handheld Analyzer Coniguration Guide for complete
information on all FieldFox products and accessories http://literature.cdn.keysight.com/litweb/pdf/5990-9836EN.pdf
1. QuickCal is not available on N995xA analyzers.
12 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Cable and Antenna Analyzer
Fifty to sixty percent of microwave-link
equipment issues are related to cables,
antennas and connectors. Degraded
feeder lines cause poor coverage, link
failures, and reduced sensitivity in the
receive path. To maintain the quality of a
microwave link, it is critical to keep cable
and antenna systems in good working
condition. FieldFox is uniquely qualiied to
provide all the necessary measurements to
troubleshoot and maintain these systems.
Insertion loss and cable loss
Insertion loss or cable loss characterizes
the loss of a jumper cable, feeder cable,
diplexer, or gain of a tower-mounted
ampliier (TMA). With FieldFox, you can
measure both the 1-port cable loss and
2-port insertion loss. Also, FieldFox’s ERTA
option, described on page 15, is useful for
measuring long, lossy in-situ cables.
Return loss/VSWR
Return loss (RL) or VSWR is the
single most important parameter used to
measure and verify a cable and antenna
system. This measurement relects the
power transfer eficiency of a given
system.
Distance-to-fault (DTF) and
time-domain relectometry (TDR)
DTF helps you determine the location
of discontinuities in feeder lines. TDR
helps you determine the nature of the
discontinuities, for example, short, open,
or water ingress.
With FieldFox, you can make RL and
DTF measurements at the same time.
This helps you correlate overall system
degradation with speciic faults in the
cable and antenna system. The built-in
cable editor lets you edit existing cable
types onsite, and save them as new cable
types with user-deined names.
View return loss and DTF simulteneously
Measure both DTF and TDR in
single sweep
FieldFox’s TDR complements RL and DTF
measurements. TDR measures impedance
changes along the cable and helps identify
speciic faults, RL exposes mismatch
issues, and DTF indicates faults and poor
connections. FieldFox is the only handheld
instrument that can measure both DTF
and TDR in a single sweep.
Characterize ilter insertion loss
Gain insight into faults with TDR measurements
13 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Cable and Antenna Analyzer (continued)
CalReady-calibrated at power
on and ready to go
Save time and get right to work with
FieldFox’s CalReady feature. With CalReady, the analyzer is already calibrated
and ready to make measurements such as
S11, S22, 1-port cable loss, and DTF/TDR
measurements without having to connect
and disconnect additional calibration
devices.
Hassle-free calibration in the
ield with QuickCal
FieldFox comes with a built-in calibration
capability that allows you to calibrate
the network analyzer without carrying a
cal kit into the ield. With any other test
instrument, when you add additional
devices to the test port, such as jumper
cables or adapters, you need to recalibrate
using a cal kit.
FieldFox’s QuickCal supports measurements such as insertion loss/gain, 1-port
cable loss, return loss, and DTF/TDR.
Note: N995xA does not support QuickCal.
Broadband calibration
FieldFox allows you to make broadband
calibrations, which means the instrument
is calibrated over the maximum frequency
range. After a broadband calibration,
you can change the frequency range or
number of points without recalibrating the
instrument. The calibration is interpolated,
and accuracy is maintained.
User cal kit support
Use FieldFox’s QuickCal capability and perform
calibrations without carrying a cal kit
For users who wish to use traditional
mechanical calibration kits, FieldFox
supports most HP/Agilent/Keysight cal
kits, and also allows you to deine your
own custom calibration kits.
Fast and accurate calibration
with ECal
The FieldFox calibration engine supports
Keysight’s USB ECal modules. ECal
support reduces calibration time and the
need to make multiple connections during
testing, while also providing for greater
consistency between measurements. For
FieldFox users, that translates into fewer
human errors and increased accuracy.
Perform fast and accurate calibrations using ECal
14 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Spectrum Analyzer
In microwave, radar, and satellite communications, and commercial microwave
backhaul, you may be responsible not only
for hardware installation and maintenance,
but also over-the-air signal quality. You
may also need to regularly monitor rogue
signals and perform signal surveillance.
FieldFox’s spectrum analyzer is
optimized to excel in a dynamic spectral
environment. You may face measurement
challenges such as the need to detect
a low-level signal under strong signal
conditions (requiring high dynamic range),
or close-in small interference signals
(requiring excellent phase noise).
FieldFox’s superior dynamic range (TOI >
+15 dBm), close in phase noise (—111 dBc/
Hz at 10 kHz), and fast sweep time make
these challenging tasks easier. FieldFox’s
spectrum analyzer also provides a full
power measurement suite and complete
trace and state control.
Unprecedented amplitude
accuracy without instrument
warm-up
With FieldFox’s InstAlign capability,
internal amplitude alignments occur
automatically as environmental conditions
change, without any user intervention.
This provides unprecedented amplitude
accuracy of ± 0.5 dB for spectrum analysis
and power measurements. Better yet,
FieldFox provides this accuracy
immediately upon instrument turn on—
no warm-up required.
Monitor frequency spectra up to 50 GHz with
FieldFox
Spectrum analyzer time gating
The testing of RF pulses is always
challenging because so many instrument
settings interact. With Option 238, gated
FFT with time gating, FieldFox behaves like
a spectrum analyzer and an oscilloscope.
This enables you to quickly detect pulses
in the time and frequency domains. A gate
time of 6 µs to 1.8 s enables simultaneous
examination of one or more pulses, or
pulse rise and fall times, revealing the
effects of spectrum growth due to various
pulse shapes. Functions such as video
trigger, external trigger and RF burst
ensure reliable pulse detection. Automatic
trigger-delay and bandwidth settings
enhance characterization of RF pulses.
Analyze pulsed RF signals using the time-gating
option
15 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Spectrum Analyzer (continued)
IF signal output
Independent signal source
FieldFox provides a spectrum analyzer
IF output with 25 MHz bandwidth. This
enables use as a frequency downconverter
and supports wideband signal analysis.
FieldFox has a built-in independent signal
source, with a frequency range of up to
50 GHz. The signal source can be tuned
to any frequency, independent of the
spectrum analyzer frequency. You can use
the signal source to create a test signal
to measure coverage, antenna isolation,
antenna direction alignment, and shielding
effectiveness, and to verify frequency-offset devices.
Field strength measurements
To characterize the electric and magnetic
ields, the gain and loss of the antenna
and cables must be accounted for. With
FieldFox, you can load antenna factors and
cable loss data using either the front panel
or the complimentary Data Link software.
Interference analyzer
Interference can be internal or external,
uplink or downlink, and has a direct
impact on the quality of service (QoS)
of a communication network. FieldFox’s interference analyzer is designed to identify
interfering signals quickly. Spectrogram
and waterfall displays detect intermittent
signals or monitor signals over a period
of time. You can record signal traces into
internal memory or external lash memory
devices, and play back the saved traces
for ofline processing. It has excellent
dynamic range with very fast sweep times
under narrow resolution bandwidths
(RBWs).
Use the internal microwave signal source for
transponder testing
Extended range transmission
analysis (ERTA)
Measuring long in situ microwave cables
such as those on ships is a challenging
task, and requires instruments with high
dynamic range and fast measurement
speed. These measurements were
traditionally done using benchtop scalar
analyzers, which are cumbersome to
operate in the ield. Using FieldFox’s ERTA,
you can measure dynamic ranges of 108
dB (at 6 GHz) or 77 dB (at 26.5 GHz) with
a portable analyzer that requires no calibration and no warm-up. ERTA uses two
FieldFoxes, one deployed at each end of
the cable. One FieldFox acts as a source,
while the other acts as a receiver. By
taking advantage of Keysight’s proprietary
InstAlign technique, this coniguration can
be used to make cable loss measurements
with accuracy of ± 0.7 dB.
Simplify interference hunting with the waterfall
display
Measure long, lossy cables using ERTA
16 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Vector Network Analyzer
FieldFox can be conigured with VNA
transmission/relection (T/R) capability
for S11 and S21 measurements, or with
full 2-port capability for measurements
of all four S-parameters and full 2-port
calibration.
With a full 2-port network analyzer, you
can measure the forward and reverse
characteristics of your component without
having to disconnect, turn around, and
reconnect it to the analyzer. Additionally,
the full 2-port calibration gives you the
best measurement accuracy possible.
Calibration
FieldFox’s guided Cal Wizard takes guessing out of calibration and allows you to
easily perform the following calibrations:
– Full 2-port unknown thru
– Full 2-port QSOLT
– OSL, response, enhanced response
– TRL, LRL, offset short
Simultaneously measure and view all four
S-parameters, with a single connection
FieldFox’s four independent, sensitive
receivers provide 94 dB of dynamic
range for measurement of high rejection,
narrowband devices such as cavity ilters.
The receivers also enable full 2-port error
correction with the unknown thru method,
allowing users to measure non-insertable
devices accurately and easily.
FieldFox’s calibration engine is the same
engine that powers the well-respected
Keysight ENA and PNA network analyzers.
FieldFox leverages Keysight microwave
expertise to deliver consistent measurements with Keysight benchtop VNAs.
Use the marker bandwidth/Q factor function to
simplify ilter testing and tuning
17 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Vector Network Analyzer (continued)
Network analyzer time domain
Vector voltmeter
With the time-domain option, FieldFox
computes the inverse Fourier transform
of the frequency-domain data to display
relection or transmission coeicients
versus time. Time-domain gating can be
used to remove unwanted responses such
as connector mismatch or cable discontinuities, and the results can be displayed
in either time or frequency domain.
Using FieldFox’s vector voltmeter (VVM),
you can measure the phase shift and
electrical length of a device. You can
view results on the large display as far as
ten feet or three meters away. VVM also
provides ratio measurements of magnitude
and phase of two channels, A/B or B/A.
You can use this capability to verify the
magnitude and phase differences between
multiple signal paths such as in an antenna
or phased array.
Waveguide support
Waveguides are widely used to provide
transmission links between microwave
transmitters and antennas, as waveguides
have less loss than coax. Keysight
offers both high-performance and also
economical waveguide calibration kits.
The economical kits are ideal for ield
maintenance and troubleshooting because
they provide good measurement results at
a lower cost.
Easily use waveguides with FieldFox
FieldFox offers all the key functionalities
of the HP 8508A in a handheld form factor,
and without the need for the source,
bridge and accessories required with the
8508A.
Mixed-mode S-parameters
With FieldFox, you can measure the common- and differential-mode relections of
a device. Mixed-mode S-parameters are
also known as balanced measurements.
This measurement requires the full 2-port
VNA and 2-port cal functionality.
Simplify cable trimming with the vector voltmeter
capability
Characterized common and differential mode relections with mixed-mode S-parameter measurements
18 | Keysight | FieldFox Handheld Analyzers – Technical Overview
USB power measurements
USB power sensor support
Pulse measurements
FieldFox can connect with Keysight
USB power sensors to make microwave
power measurements. Using USB peak
power sensors, you can measure both
the average and the peak power of a
modulated signal.
FieldFox’s pulse measurement option
allows you to eficiently characterize
pulsed RF signals such as those used in
radar and electronic warfare systems,
leveraging the Keysight USB peak power
sensors. Measurements include peak
power, peak to average ratio, and pulse
proile parameters such as rise time, fall
time and pulse repetition frequency.
USB power measurements
versus frequency
Simplify power measurements with USB power
sensors
In addition to power measurements at a
single CW frequency, you can measure
power versus frequency - a swept measurement. FieldFox’s source frequency
can be set equal to the sensor/receiver
frequency, or with an offset. The frequency
of both the source and receiver are swept,
and the two track each other. The offset
frequency can be negative, zero, or
positive.
This capability is useful for characterization of the scalar transmission response
of devices such as mixers and converters.
The FieldFox source stimulates the DUT
and the power sensor is used as the
measurement receiver.
Characterize mixers with FieldFox and a USB
power sensor
Use FieldFox to characterize pulses
19 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Software and System Features
Remote control capability with
iPad and iPhone
Engineers and technicians can now
remotely monitor and control their
FieldFox using their iOS device such as
an iPhone, iPad, or iPod Touch. FieldFox’s
Remote Viewer iOS app emulates the
front panel of the unit, letting you simply
press any FieldFox key right from your
iOS device. The app also allows you to
instantly access technical documents
such as data sheets.
FieldFox’s Data Link software
makes report generation and
documentation easier
FieldFox’s complimentary Data Link
software provides data transfer, data
deinition and report generation. You can
add markers and limit lines to traces,
and you can load cable iles and antenna
factors using Data Link.
Remote control via LAN and
FieldFox programming
Built-in variable voltage DC bias
FieldFox has a built-in variable voltage
DC bias source. The DC bias source can
provide DC power to ampliiers under test
and bias tower mounted ampliiers (TMA)
when you need to sweep through the TMA
to reach the antenna (bias tees available
separately).
Built-in GPS
Control and view your FieldFox via your iPad
A built-in GPS receiver provides
geo-location tags to measurements.
The geo data—time, latitude, longitude,
and elevation—can be displayed and
saved in data iles. In addition to location
information, the GPS provides an external
reference to improve FieldFox frequency
accuracy.
USB keyboard and mouse
support
Obtain geolocation data with the built-in GPS
capability
FieldFox supports use of USB keyboards
and mice to simplify the input of text such
as ile names while working in the ield.
All FieldFox models can be controlled
using SCPI over LAN. The N995xA and
N996xA models can additionally be
controlled using SCPI over USB.
Simplify text entry with a USB keyboard and mouse
20 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Designed for You and the Work You Do Everyday
Carry FieldFox wherever you
need to go
Field-proof usability for better
answers in less time
– Kit friendly at 6.6 lb (3.0 kg) for the
N991/2/3xA and 7.1 lb (3.2 kg) for the
N995/6xA
– Bright, low-relection display and
backlit keys enable easy viewing in
direct sunlight or darkness
– Large buttons are easy to operate,
even when wearing gloves
– Intuitive user interface is designed
for your worklow, enabling measurements in fewer key presses
– Field swappable battery lasts up to
3.5 hours
– Non-slip rubber grip securely its in
your hands and won’t slide off the
hood of your vehicle
– Vertical “portrait” orientation makes
it easy to hold and operate at the
same time
– One-button measurements simplify
complex setups and ensure quick,
accurate results with conidence
– Calibration Wizard guides user
to ensure simple and accurate
calibrations
– Three-year warranty ensures ield
conidence, especially in harsh
environments
Easily operate FieldFox, even when wearing
gloves, through the large frontpanel keys
Read measurements in direct sunlight with
the translective display
21 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Designed for Your Toughest Working Conditions
Rugged enough to meet MIL-specs
– Completely sealed instrument enclosure provides
measurement stability in harsh environments, -10 to +55 ºC
(14 to 131 ºF)
– Specially designed to protect instrument from damage due
to drops, shock or other external impacts
– Water-resistant chassis, keypad and case withstand wide
temperature ranges and salty, humid environments
– Meets MIL-PRF-28800F Class 2 requirements
– Type tested and meets MIL-STD-810G, Method 511.5,
Procedure I requirements for operation in explosive
environments
– Type tested and meets IEC/EN 60529 requirements for
ingress protection
Count on extended instrument reliability with FieldFox’s dust-free design:
no vents or fans
22 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Configuration in Brief
See the FieldFox Handheld Analyzer Coniguration Guide for complete information on all FieldFox products and accesories
http://literature.cdn.keysight.com/litweb/pdf/5990-9836EN.pdf
RF and microwave analyzers are referred to as combination analyzers in this section.
Option
Description
CAT/network analysis
010
VNA time domain
112
QuickCal
210
VNA transmission/relection
211
VNA full 2-port S-parameters
212
1-port mixed-mode S-parameters
215
TDR cable measurements
305
Cable and antenna analyzer
308
Vector voltmeter
320
Relection meas. (RL, VSWR and scalar meas.)
Spectrum analyzer
209
Extended range transmission analysis (ERTA)
220
Tracking generator
233
Spectrum analyzer
235
Pre-ampliier
236
Interference analyzer and spectrogram
238
Spectrum analyzer time gating
Power measurements
208
USB power sensor meas. versus frequency
302
USB power sensor support
310
Built-in power meter
330
Pulse meas. with USB peak power sensor
System features
030
Remote control capability
307
GPS receiver
309
DC bias variable-voltage source
Combination analyzers
Vector network analyzers
Spectrum analyzers
N991xA
N995xA
N992xA
N993xA
N996xA
ü
ü
-
ü
–
ü
Base model
–
ü
ü
ü on N991xA
not on N995xA
ü
ü
Base model
ü
ü
ü
ü
ü
–
–
–
Note 1
–
Note 2
Note 2
ü
ü
–
ü
Note 3
–
ü
–
Base model
ü
ü
ü
ü
–
–
ü
ü
-
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
Notes:
Base model means that the functionality listed is the primary function of that instrument. For example, on the N991xA or N995xA combo analyzers, cable and
antenna analysis is the standard function included with every N991xA or N995xA.
1. Option 305 is not available on the N993xA or N996xA. However, a subset of cable and antenna analyzer measurements, return loss and VSWR, is available
as Option 320.
2. Option 320 is not applicable to N991xA, N995xA, or N992xA. The relection measurements of return loss and VSWR are included with every N991xA,
N995xA, and N992xA. So there is no need for an Option 320 on these analyzers.
3. On the N991xA or N995xA analyzers, order Options 233 and 210 to obtain a tracking generator with the spectrum analyzer. There is no Option 220 on the
N991xA or N995xA analyzers. To obtain tracking generator capability, you need Options 233 and 210. Option 233 provides the spectrum analyzer capability
and Option 210 the “tracking” capability.
23 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Specifications in Brief
See the FieldFox Handheld Analyzer Data Sheet for a complete listing of the speciications:
http://literature.cdn.keysight.com/litweb/pdf/5990-9783EN.pdf
Cable and antenna tester is referred to as CAT and vector network analyzer is referenced as VNA in this section.
Model
CAT and VNA frequency
Spectrum analyzer frequency 1
Test port connectors
RF & microwave (combination) analyzers
N9913A
30 kHz to 4 GHz
100 kHz to 4 GHz
Type-N (f)
N9914A
30 kHz to 6.5 GHz
100 kHz to 6.5 GHz
Type-N (f)
N9915A
30 kHz to 9 GHz
100 kHz to 9 GHz
Type-N (f)
N9916A
30 kHz to 14 GHz
100 kHz to 14 GHz
Type-N (f)
N9917A
30 kHz to 18 GHz
100 kHz to 18 GHz
Type-N (f)
N9918A
30 kHz to 26.5 GHz
100 kHz to 26.5 GHz
3.5 mm (m)
N9950A
300 kHz to 32 GHz
9 kHz to 32 GHz
NMD 2.4 mm (m)
N9951A
300 kHz to 44 GHz
9 kHz to 44 GHz
NMD 2.4 mm (m)
N9952A
300 kHz to 50 GHz
9 kHz to 50 GHz
NMD 2.4 mm (m)
N9925A
30 kHz to 9 GHz
–
Type-N (f)
N9926A
30 kHz to 14 GHz
–
Type-N (f)
N9927A
30 kHz to 18 GHz
–
Type-N (f)
N9928A
30 kHz to 26.5 GHz
–
3.5 mm (m)
N9935A
–
100 kHz to 9 GHz
Type-N (f)
N9936A
–
100 kHz to 14 GHz
Type-N (f)
N9937A
–
100 kHz to 18 GHz
Type-N (f)
N9938A
–
100 kHz to 26.5 GHz
Type-N (f) 2
N9960A
–
9 kHz to 32 GHz
NMD 2.4 mm (m)
N9961A
–
9 kHz to 44 GHz
NMD 2.4 mm (m)
N9962A
–
9 kHz to 50 GHz
NMD 2.4 mm (m)
Vector network analyzers
Spectrum analyzers
Notes:
1. Usable to 5 kHz.
2. Order Option 100 for 3.5 mm (m) test port connectors. With N9938A-100, the spectrum analyzer is built with 3.5 mm test port connectors instead of the
standard Type-N (f). Option 100 is a prerequisite for Option 320 for N9938A.
24 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Specifications in Brief (continued)
Cable and antenna analyzer (CAT) and vector network analyzer (VNA)
The performance listed in this section applies to the cable and antenna analyzer (referred to as CAT) and vector network analyzer
(referred to as VNA) capabilities.
N9913 /14 /15 /16 /17 /18A
N9925 /26 /27 /28A
Model
N9950 /51 /52A
Measurements
CAT
Distance-to-fault (dB), return loss, VSWR, DTF (VSWR), cable loss (1 port), optional insertion loss
(2 port), DTF (linear), DTF / return loss dual display
TDR cable measurements
TDR (rho), TDR (ohm), DTF / TDR dual display
VNA T/R
S11, S21 and insertion loss under CAT
VNA full 2 port
S11, S21, S22, S12 mag and phase, VSWR, linear, phase, Smith chart, polar, group delay,
unwrapped phase, real/imaginary
Calibration types
CalReady, 1-port OSL, frequency response, enhanced response, QSOLT, unknown thru 2-port, ECal, QuickCal*
*not available in N995xA models
Number of traces
4
Number of markers
6
Marker functions
Data points
Peak, minimum, target, bandwidth measurement with Q, marker tracking
101, 201, 401, 601, 801, 1001 ,1601, 4001, 10,001
Frequency reference : -10 to 55 °C
Accuracy
± 0.7 ppm (spec) + aging
± 0.4 ppm (typical) + aging
Accuracy, when locked to GPS
Aging Rate
Corrected directivity (with full 2-port calibration)
± 0.01 ppm (spec)
± 1 ppm/year for 20 years (spec), will not exceed ± 3.5 ppm
Using 85520A or 85521A
cal kit
Using 85056D
cal kit
42 dB
–
< 0.5 to 9 GHz
36 dB
–
< 9 to 8 GHz
32 dB
–
< 18 to 26.5 GHz
32 dB
–
≤ 0.5 GHz
≤ 2 GHz
–
42 dB
< 2 to 20 GHz
–
34 dB
< 20 to 40 GHz
–
26 dB
< 40 to 50 GHz
–
26 dB
25 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Specifications in Brief (continued)
Model
N9913 /14 /15 /16 /17 /18A
N9950 /51 /52A
N9925 /26 /27 /28A
Test port output power (high power)
Frequency
Typical
Typical
Port 1 or port 2
30 to 300 kHz
—11 dBm
–
> 300 kHz to 2 MHz
—3 dBm
–
> 2 to 625 MHz
—2 dBm
–
> 625 MHz to 3 GHz
1 dBm
–
—1 dBm
–
> 6.5 to 9 GHz
—2 dBm
–
> 9 to 14 GHz
—4 dBm
–
> 14 to 18 GHz
—6 dBm
–
> 18 to 23 GHz
—10 dBm
–
> 23 to 26.5 GHz
—12 dBm
–
> 3 to 6.5 GHz
300 kHz to 2 MHz
Port 1
Port 2
–
0 dBm
0 dBm
> 2 MHz to 1 GHz
–
2 dBm
2 dBm
> 1 to 6.5 GHz
–
2 dBm
0 dBm
> 6.5 to 18 GHz
–
4 dBm
1 dBm
> 18 to 39 GHz
–
1 dBm
-2 dBm
> 39 to 46 GHz
–
-2 dBm
-5 dBm
> 46 to 50 GHz
–
-4 dBm
-7 dBm
Test port output power (low power)
Port 1 or port 2
30 kHz to 26.5 GHz
—45 dBm (lattened), nominal
–
Port 1
Port 2
–
-35 dBm
-38 dBm
> 10 MHz to 10 GHz
–
-38 dBm
-42 dBm
> 10 to 20 GHz
–
-43 dBm
-47 dBm
> 20 to 44 GHz
–
-44 dBm
-50 dBm
> 44 to 50 GHz
–
-53 dBm
-55 dBm
500 kHz to 10 MHz
Power level accuracy (typical)
± 1.5 dB at —15 dBm
for frequencies > 250 kHz
± 0.7 dB at −15 dBm,
for frequencies > 500 kHz to 10 MHz
± 0.5 dB at −15 dBm,
for frequencies > 10 MHz to 50 GHz
Power step size
Flat power, in 1 dB steps, is available across the whole frequency span (nominal)
26 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Speciications in Brief (continued)
N9913 /14 /15 /16 /17 /18A
N9925 /26 /27 /28A
Model
N9950 /51 /52A
Distance to fault
Range
Range = velocity factor x speed of light x (number of points -1) / frequency span x 2
Number of points auto coupled according to start and stop distance entered.
Range resolution
Resolution = range / (number of points -1)
System dynamic range
1, 2
Frequency
> 300 kHz to 9 GHz
3
: Port 1 or port 2, high power, 300 Hz IF bandwidth, —10 to 55 °C
Spec
Typical
Spec
Typical
95 dB
100 dB
–
–
> 9 to 14 GHz
91 dB
97 dB
–
–
> 14 to 18 GHz
90 dB
94 dB
–
–
> 18 to 20 GHz
87 dB
90 dB
–
–
> 20 to 25 GHz
74 dB
79 dB
–
–
> 25 to 26.5 GHz
65 dB
70 dB
–
–
> 300 kHz to 1 MHz
–
–
–
> 1 to 10 MHz
–
–
–
> 10 MHz to 20 GHz 4
–
–
100 dB
110 dB
> 20 to 44 GHz
–
–
90 dB
100 dB
–
–
81 dB
90 dB
> 44 to 50 GHz
5
70 dB (nominal)
100 dB (nominal)
Trace noise 6: Port 1 or port 2, high power, 300 Hz IF bandwidth, spec, —10 to 55 °C
Frequency
Magnitude/Phase (dB rms/deg rms)
> 300 kHz to 20 GHz
± 0.004 / ± 0.070
> 20 to 26.5 GHz
± 0.007/ ± 0.140
> 26.5 to 32 GHz
± 0.007/ ± 0.140
> 32 to 50 GHz
± 0.008 / ± 0.220
IF Bandwidth 7
Bandwidth
10 Hz, 30 Hz, 100 Hz, 300 Hz, 1 kHz, 3 kHz, 10 kHz, 30 kHz, 100 kHz
1. System dynamic range is measured in production with loads on test ports after thru normalization, test port output power high.
2. For CAT mode, “Insertion loss (2-port)”, decrease listed dynamic range speciications by 20 dB, as CAT mode IFBW is ixed at 10 kHz. Can obtain full
dynamic range by using S21 measurement in VNA mode with 100 Hz IFBW.
3. < 300 kHz: 63 dB nominal; 2 MHz to 9 MHz: 85 dB spec, 90 dB typical.
4. Decrease by 3 dB between 15 to 15.8 GHz.
5. Listed spec applies to S12, decrease by 4 dB for S21.
6. For CAT mode, increase trace noise by a factor of 5.7, as CAT mode IFBW is ixed at 10 kHz. Can use averaging in CAT mode to reduce trace noise or use
VNA mode with 300 Hz IFBW.
7. VNA mode only. Recommend using averaging in CAT mode.
27 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Speciications in Brief (continued)
Spectrum analyzer
The performance listed in this section applies to the spectrum analyzer capabilities.
Model
N9913 /14 /15 /16 /17 /18A
N9935 /36 /37 /38A
N9950 /51 /52A
N9960 /61 /62A
Measurements
Spectrum analyzer
Spectrum, channel power, adjacent power, ocuppied bandwidth, tune and listen
Number of traces
Same as network analyzer (see page 24)
Number of markers
Same as network analyzer (see page 24)
Interference analysis
Spectrogram, waterfall and record/playback
Input attenuator range
0 to 30 dB, in 5 dB steps
Frequency span
Resolution: 1 Hz
Frequency reference : -10 to 55 ° C
Same as network analyzer (see page 24)
Preampliier
The preampliier covers the full-band with nominal gain of 20 dB
Tracking generator
Built in, full-band based on the model maximum frequency
Resolution bandwidth (RBW), range (-3 dB bandwidth)
Zero span: 10 Hz to 5 MHz: 1, 3, 10 sequence
Non zero span: 1 Hz to 5 MHz: 1, 1.5, 2, 3, 5, 7.5, 10 sequence
Video bandwidth (VBW)
1 Hz to 5 MHz in 1, 1.5 , 2, 3, 5, 7.5, 10 sequence
Phase noise: Stability, SSB phase noise at 1 GHz
Offset
Spec (23 ± 5 ºC)
Typical (23 ± 5 ºC)
10 kHz
—106 dBc
—111 dBc
30 kHz
—106 dBc
—108 dBc
100 kHz
—100 dBc
—104 dBc
1 MHz
—110 dBc
—113 dBc
3 MHz
—119 dBc
—122 dBc
5 MHz
—120 dBc
—123 dBc
50 MHz absolute amplitude accuracy
10 dB attenuation, input signal 0 to -35 dBm, peak detector, preampliier off, 300 Hz RBW, all settings auto-coupled, -10 to 55 °C.
No warm-up required.
Spec
± 0.3 dB
Typical
± 0.1 dB
Spec
± 0.45 dB
Typical
± 0.2 dB
Total absolute amplitude accuracy Temperature (23 ± 5 ºC)
10 dB attenuation, input signal -10 to -5 dBm, peak detector, preampliier off, 300 Hz RBW, all settings auto-coupled, includes frequency response
uncertainties. No warm-up required.
100 kHz to 18 GHz
> 18 to 26.5 GHz
> 9 to 100 kHz
Spec
Typical
Spec
Typical
± 0.8 dB
± 0.35 dB
–
–
± 1.0 dB
± 0.5 dB
–
–
–
–
± 1.6 dB
± 0.6 dB
> 100 kHz to 2 MHz
–
–
± 1.3 dB
± 0.6 dB
> 2 MHz to 32 GHz
–
–
± 0.8 dB
± 0.3 dB
> 32 to 40 GHz
–
–
± 0.9 dB
± 0.5 dB
> 40 to 43 GHz
–
–
± 1.3 dB
± 0.5 dB
> 43 to 50 GHz
–
–
± 1.4 dB
± 0.5 dB
28 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Speciications in Brief (continued)
N9913 /14 /15 /16 /17 /18A
N9935 /36 /37 /38A
Model
N9950 /51 /52A
N9960 /61 /62A
Displayed average noise level (DANL): RMS detection, log averaging, reference level of —20 dBm, normalized to 1 Hz RBW
Preamp on (23 ± 5 ºC)
Spec
Typical
Spec
Typical
2 MHz to 4.5 GHz 1
—153 dBm
—155 dBm
–
–
> 4.5 to 7 GHz
—149 dBm
—151 dBm
–
–
> 7 to 13 GHz
—147 dBm
—149 dBm
–
–
> 13 to 17 GHz
—143 dBm
—145 dBm
–
–
> 17 to 22 GHz
—140 dBm
—143 dBm
–
–
> 22 to 25 GHz
—134 dBm
—137 dBm
–
–
> 25 to 26.5 GHz
—128 dBm
—131 dBm
–
–
9 kHz to 2 MHz
–
–
—94 dBm
—131 dBm
> 2 MHz to 2.1 GHz
–
–
—153 dBm
—159 dBm
> 2.1 to 2.8 GHz
–
–
—151 dBm
—157 dBm
> 2.8 to 4.5 GHz
–
–
—153 dBm
—158 dBm
> 4.5 to 7 GHz
–
–
—150 dBm
—156 dBm
> 7 to 13 GHz
–
–
—146 dBm
—152 dBm
> 13 to 22 GHz
–
–
—142 dBm
—149 dBm
> 22 to 35 GHz
–
–
—141 dBm
—147 dBm
> 35 to 40 GHz
–
–
—136 dBm
—144 dBm
> 40 to 46 GHz
–
–
—131 dBm
—138 dBm
> 46 to 50 GHz
–
–
—126 dBm
—135 dBm
Third order intermodulation distortion (TOI)
Two —20 dBm signals, 100 kHz spacing
at input mixer, —10 to 55 °C
Spec
At 2.4 GHz, +15 dBm
1.
Add 4 dB between 2.1 and 2.8 GHz.
Typical
< 1 GHz, +10 dBm
Spec
At 2.4 GHz, +15 dBm
Typical
50 to 500 MHz, +9.5 dBm
–
1 to 7.5 GHz, +15 dBm
–
> 500 MHz to 1 GHz, +13 dBm
–
> 7.5 GHz, +21 dBm
–
> 1 to 2.4 GHz, +16 dBm
–
> 2.4 to 2.6 GHz, +12 dBm
–
> 2.6 GHz, +13 dBm
29 | Keysight | FieldFox Handheld Analyzers – Technical Overview
General information
Model
N9913 /14 /15 /16 /17 /18A
N9925 /26 /27 /28A
N9935 /36 /37 /38A
N9950 /51 /52A
N9960 /61 /62A
Weight
3.0 kg or 6.6 lb including battery
3.2 kg or 7.1 lb including battery
Dimension H x W x D
Battery
Calibration cycle
Warranty
292 x 188 x 72 mm (11.5" x 7.4" x 2.8")
Lithium ion, 10.8 V, 4.6 A-h, 3.5 hours (typical)
1 year
3-year warranty standard on all FieldFox instruments
Environmental
MIL-PRF-28800F Class 2
Operating temperature, storing temperature, storing temperature, operating humidity,
random vibration, functional shock, bench drop
MIL-STD-810G, Method 511.5
This product has been type tested to meet the requirements for operating in explosive
environments in accordance with MIL-STD-810G, Method 511.5, Procedure 1.
Ingress protection
Complies with European EMC directive
This product has been type tested to meet the requirements for ingress protection IP53 in
accordance with IEC/EN 60529 (IP rating for instrument by itself with no cover).
IEC/EN 61326–1
CISPR Pub 11 Group 1, class B, Group 1 limit of CISPR 11:203/EN
55011:2007
AS/NZS CISPR 11
ICES/NMB–001
30 | Keysight | FieldFox Handheld Analyzers – Technical Overview
Accessories in Brief
See the FieldFox Handheld Analyzer Coniguration Guide for a comprehensive list of all FieldFox accessories.
http://literature.cdn.keysight.com/litweb/pdf/5990-9836EN.pdf
RF and microwave accesories
Cables
N9910X-709
Phase stable cable (3.5 mm (f) to 3.5 mm (f), 26.5 GHz, 3.28 ft or 1 m)
N9910X-810
Phase stable cable (Type-N (m) to Type-N (m), 6 GHz, 5 ft or 1.5 m)
Calibration kits
N9910X-800
3-in- OSL calibration kit (DC to 6 GHz, Type-N (m) 50 ohm)
85520A
4-in-1 OSLT calibration kit (DC to 26.5 GHz, 3.5 mm (m) 50 ohm)
N4690C
Electronic calibration module (ECal), 300 kHz to 18 GHz, Type-N, 50 ohm, 2-port
85056A
Mechanical calibration kit, DC to 50 GHz, 2.4 mm
85056D
Economy mechanical calibration kit, DC to 50 GHz, 2.4 mm
Antennas
N9910X-820
Directional antenna (multiband 800 MHz to 2.5 GHz, 10 dBi, Type-N (f))
N9910X-821
Telescopic whip antenna (70 MHz to 1 GHz, 10 dBi, BNC (m))
Carry Precision With You
Every piece of gear in your ield kit had to prove its worth. Measuring up and earning a
spot is the driving idea behind Keysight’s FieldFox analyzers. They’re equipped to handle
routine maintenance, in-depth troubleshooting and anything in between. Better yet,
FieldFox delivers precise microwave and millimeter-wave measurements—wherever you
need to go. Add FieldFox to your kit and carry precision with you.
Related literature
Number
FieldFox Handheld Analyzers, Data Sheet
5990-9783EN
FieldFox Handheld Analyzers, Coniguration Guide
5990-9836EN
FieldFox N9912A RF Analyzer, Technical Overview
5989-8618EN
FieldFox N9912A RF Analyzer, Data Sheet
N9912-90006
FieldFox N9923A RF Vector Network Analyzer, Technical Overview
5990-5087EN
FieldFox N9923A RF Vector Network Analyzer, Data Sheet
5990-5363EN
Download application notes, watch videos, and learn more:
www.keysight.com/ind/ieldfox
31 | Keysight | FieldFox Handheld Analyzers – Technical Overview
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System
Keysight Infoline
www.keysight.com/find/service
Keysight’s insight to best in class information management. Free access to
your Keysight equipment company reports and e-library.
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
www.keysight.com/find/fieldfox
www.keysight.com/find/fieldtest
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Paciic
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 11 2626
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
Austria
Belgium
Finland
France
Germany
Ireland
Israel
Italy
Luxembourg
Netherlands
Russia
Spain
Sweden
Switzerland
United Kingdom
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-04-23-15)
This information is subject to change without notice.
© Keysight Technologies, 2012 – 2015
Published in USA, August 14, 2015
5992-0772EN
www.keysight.com

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project