- Entertainment & hobby
- Musical instruments
- Musical Instrument Amplifier
- Kustom
- GROOVE 410H
- Owner's manual
Kustom GROOVE 410H Owner's Manual
Add to my manuals8 Pages
Kustom GROOVE 410H is a bass guitar speaker cabinet designed to offer exceptional sound quality and long-term performance reliability. It features four 10-inch Eminence speakers with an average sensitivity of 35-5Khz, providing a frequency response of 40Hz-15kHz. The cabinet has an impedance of 8 ohms and can handle up to 500 watts of power.
The GROOVE 410H is equipped with a horn attenuator that allows you to adjust the volume of the horn to your preference. It also has two 1/4-inch input/output jacks and two Speakon input/output jacks, giving you the flexibility to connect to a variety of amplifiers and other equipment.
advertisement
OWNER'S MANUAL
GROOVE 410H
Congratulations on the purchase of your new Kustom bass guitar speaker cabinet!
Your new GROOVE 410H has been designed to offer exceptional sound quality and long-term performance reliability. Inside this manual you’ll find detailed information regarding the cabinet’s features. We wish you many years of enjoyment with your
Kustom GROOVE 410H.
Product Contents
These items are included with your GROOVE 410H speaker cabinet.
Be sure to contact your dealer if any items are missing.
GROOVE 410H
Speaker Cable
KAC-GRVSCC
Caster Plate
KAC-GCP
(Packaged Separately)
2
Warranty Card
7
6
8
10
12
16
5
4
0
3
2
1
Rear Panel
2
MODEL: GROOVE 410H
IMPEDANCE: 8 OHMS
POWER: 500 WATTS RMS
SENSITIVITY:95dB 1W/1M
+1 tip, -1 sleeve
INPUT/OUTPUT
+1 and -1 used
HORN ATTENUATION dB
Designed by Kustom Inc. Cincinnati, Ohio
MADE IN CHINA
1
1
Horn Attenuator:
This is a “volume” control for the horn. To disable the horn, turn the knob counter clockwise until the indicator reaches
:
. To set the horn for maximum output, turn the knob
2
Speaker Input/Output
:
These jacks can be used as an input and/or output. The jacks accept a standard
¼
” cable.
Note:
When using these jacks as an output to another cabinet, refer to the Amplifier Loading
Chart (page 4) for important amplifier loading information.
XXXX-XXXXXX
3
3
Speaker Input/Output
:
These jacks can be used as an input and/or output. They accept standard
Speakon type speaker cables. To connect a cable: Insert and twist one quarter turn clockwise until the release button locks. To remove a cable: Pull back release button on cable connector, twist connector counter clockwise one quarter turn, and pull out connector.
Note:
When using these jacks as an output to another cabinet, refer to the
Amplifier Loading Chart (page 4) for important amplifier loading information.
3
Speaker Connection Diagram
(Shown using the Kustom GROOVE 1200 amplifier)
15
15A
BREAKER
MODEL: GROOVE 1200
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
SERIAL NUMBER
DESIGNED IN USA
MADE IN CHINA
2001124
CAUTION
CHASSIS SURFACE HOT
ATTENTION
SUPERFICE DE CHASSIS CHAUDE
SPEAKER OUTPUT
GROUND PRE EQ
LIFT
DIRECT OUTPUT
EFFECTS LOOP
POST EQ
TUNER OUT
SEND RETURN FOOTSWITCH
Cabinet
A
Cabinet
B
Speaker cabinet loads (ohms) applied to the amplifier
Cabinet
B’s
Impedance open
16
8
5.33
4
3.20
2.67
2
Amplifier Loading Chart
Cabinet A’s Impedance (ohms) open open
16
8
5.33
4
3.2
16
16
8.00
5.33
4.00
3.20
2.67
8
8
5.33
4.00
3.20
2.67
2.29
5.33
5.33
4.00
3.20
2.67
2.29
2.00
4
4
3.20
2.67
2.29
2.00
1.78
3.20
3.2
2.67
2.29
2.00
1.78
1.60
2.67
2.67
2.29
2.00
1.78
1.60
1.46
2.67
2
2.29
1.78
2.00
1.60
1.78
1.45
1.60
1.33
1.46
1.23
1.34
1.14
Total load on amplifier Note: Refer to amplifier specifications for proper loading information.
1.14
1.00
2
2
1.78
1.60
1.45
1.33
1.23
This chart can help you determine what load (ohms) is present on the amplifier when using multiple cabinets.
- To use this chart with two cabinets (A and B), find cabinet A’s impedance (ohms) column and cabinet B’s impedance row on the chart. The total load on the amplifier is shown in the box where they meet. For example: If cabinet A’s impedance is 8 ohms and cabinet B’s impedance is 4 ohms, the total load on the amplifier would be 2.67
ohms.
- To use this chart with three or more cabinets, find the total load for two cabinets and then use the result for cabinet A’s impedance column. The third cabinet will then be used for cabinet B’s impedance row on the chart.
Find the total load on the amplifier and repeat if more cabinets are used. For example (using 3 cabinets): If the first cabinet (cabinet A) has an impedance of 16 ohms and the second (cabinet B) has an impedance of 8 ohms, the total load would be 5.33 ohms. Using this load (5.33) as cabinet A’s impedance and a third cabinet’s (new cabinet
B) impedance of 4 ohms, you would find that the total load on the amplifier is 2.29 ohms.
Note: It is not recommended to use any combination of cabinets that has a resulting load in a shaded area of the chart.
Alternate Connection Diagrams
15A
BREAKER
MODEL: GROOVE 1200
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
SERIAL NUMBER
DESIGNED IN USA
MADE IN CHINA
2001124
CAUTION
CHASSIS SURFACE HOT
ATTENTION
SUPERFICE DE CHASSIS CHAUDE SPEAKER OUTPUT
GROUND PRE EQ
LIFT
DIRECT OUTPUT
EFFECTS LOOP
POST EQ
TUNER OUT
SEND RETURN FOOTSWITCH
15A
BREAKER
MODEL: GROOVE 1200
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
SERIAL NUMBER
DESIGNED IN USA
MADE IN CHINA
2001124
CAUTION
CHASSIS SURFACE HOT
ATTENTION
SUPERFICE DE CHASSIS CHAUDE
SPEAKER OUTPUT
GROUND PRE EQ
LIFT
DIRECT OUTPUT
EFFECTS LOOP
POST EQ
TUNER OUT
SEND RETURN FOOTSWITCH
8 Ohms 8 Ohms 8 Ohms 8 Ohms =
8 Ohms 8 Ohms
Total Load On Amplifier = 2 Ohms
8 Ohms 8 Ohms
Total Load On Amplifier = 2 Ohms
4
GROOVE 410H
Specifications
Model
Input Power
Impedence
Speakers
Sensitivity per speaker
Frequency Response
Dimensions
Accessories Included
Groove 410H
500 Watts
8 Ohms
4 X 10"
95dB 1W at 1 meter
40HZ-15kHz mm/kg
Inches/Pounds
Speakon Cable
Caster Plate
Bass guitar speaker cabinet
RMS
Specially Designed Eminence Speakers
Average sensitivity 35-5Khz using factory test conditions
System Response
820 (Height) x 617 (Width) x 510 (Depth), 46.4 kg
32.25 (Height) x 24.25 (Width) x 20.125 (Depth), 102.3 lbs
3 meter Speakon speaker cable
Plywood with swivel casters
5
6
EC Declaration of Conformity
We: Kustom Musical Amplification Inc.
4940 Delhi Pike
Cincinnati, OH 45238
Tel: 1-513-451-5000 Fax: 1-513-347-2192
Declare that the product
Product name:
Product model number:
Kustom
GROOVE 410H to which this declaration relates is in conformity with the following standards;
EN55013 (A12) : 1995 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment.
EN55020: 1995
EN61000-3-2: 1995
EN61000-3-3: 1995
Electromagnetic immunity of broadcast receivers and associated equipment.
Limits for harmonic current emissions (equipment input current rated currents < 16A.
< 16A per phase).
Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with
EN55103-1: 1995
EN60065: 1994
Electromagnetic Compatibility - Product family standard for Audio, Video Audio-visual and entertainment Lighting Control Apparatus.
Safety requirements for main operated electronic and related apparatus for household and similar general use.
Following the provisions of EU Council Directive(s): 72/73 EEC and 89/336/EEC.
We the undersigned, hereby declare that the equipment specified above conforms to the aforementioned directive(s).
Name of authorized person: Rick Kukulies, VP Engineering
Signature:______________________ Date: 05 June 2001
Kustom Musical Amplification Inc. (BC Rich)
4940 Delhi Pike
Cincinnati, OH 45238
Tel: 1-513-451-5000 Fax: 1-513-347-2192
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project