Unique Appliances UGP-30E OF1 Cooking Appliance Product manual

Add to My manuals
51 Pages

advertisement

Unique Appliances UGP-30E OF1 Cooking Appliance Product manual | Manualzz

OFF GRID PROFESSIONAL

GAS RANGE

UGP-30E OF1

UGP-36E OF1

OWNER’S GUIDE

Read and save these instructions

serial number:

MAY 2015

TB

30E & 36E MODELS

OFF GRID GAS RANGE – LPG & NG CONVERTIBLE

Installation and Owner’s Manual

This manual contains information for:

Important Safeguards

Installation

Use and Care

Certain ranges come equipped with special features. Determine from a study of your range which of the instructions given in this booklet pertain to your range.

This booklet gives valuable instructions covering the installation, adjustment and use of your range.

How to Obtain Service and/or Parts

When your range does not operate in accordance with the instructions in the manual, you should contact the dealer in your immediate vicinity for service. Or, the purchaser may contact the service organization noted on the warranty.

Important

TO THE OWNER OF THE RANGE: Retain this owner’s manual for future reference.

TO THE INSTALLER: Leave this owner’s manual with the range.

Read and Save These Instructions

The installation of the appliance must conform with local codes ANSI

Z21.1a-2010, in the absence of local national Fuel Gas Code, ANSI Z233.1, and in Canada B149.2 Propane Storage and Handling Code

M A N U F A C T U R E D A N D C E R T I F I E D B Y

Unique Gas Products Ltd

2245 Wyecroft Road

Oakville, Ontario Canada L6L 5L7

Ph: 905-827-6154 Toll Free: 1-877-427-2266 Fax: 905-827-2027

www.UniqueOffGrid.com

Table of Contents

Contents

Welcome & Congratulations

Dimensions and Clearances

Installation Instructions

First use of your new Range and Oven

Cooktop Use

Operation of Range

Care and Cleaning the Range

Removing or Replacing the Oven Door

How to Gain Access to the Battery

Troubleshooting Guide

Wiring Diagrams

Parts List and Diagrams

Warranty

Pages 1 thru 7

Pages 8 thru 12

Pages 13 thru 17

Pages 18 thru 19

Pages 20 thru 25

Pages 26 thru 29

Pages 29 thru 32

Pages 33 thru 34

Page 35

Pages 36 thru 38

Pages 39 thru 40

Pages 41 thru 46

Page 47

U N I Q U E E L I T E 3 0 E & 3 6 E

Welcome &

Congratulations

C ongratulations on your purchase of a

UNIQUE

Elite range!. We are very proud of our products and are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority. Please read this manual very carefully. It contains valuable information on how to properly maintain your new Unique gas range.

We know you will enjoy your new range and Thank You for choosing Unique! We hope you will consider us for future purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This manual provides specific operation instructions for your model. Use your range only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining the appliance

Record in the space provided below the Model No. and Serial No. of this appliance.

These numbers are found on the serial plate located at the back of the appliance near the gas inlet connection .

Model No. ________________________ Type Number _______________________

Serial No. ________________________ Purchase Date________________________

Record these numbers for future use.

IMPORTANT:

Keep a copy of your bill of sale. The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

PLEASE DO THIS NOW!

The PRODUCT REGISTRATION CARD should be filled in completely, signed and returned. This information will register your product and help us to serve you quickly in the future if necessary.

.

1

U N I Q U E E L I T E 3 0 E & 3 6 E

If you smell gas

READ ALL IMPORTANT SAFEGUARDS AND

Open Windows

Don’t touch electrical switches

Extinguish any open flame

Immediately call your gas supplier

F

OR YOU

S

AFETY

Keep appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids.

Warnings

Destroy the carton and plastic bags after the range is unpacked. Children should not use packaging material for play. Cartons covered with rugs, bedspreads, or plastic sheets can become air-tight chambers. Remove all staples from the carton. Staples can cause severe cuts and destroy finishes if they come in contact with other appliances or furniture.

Be safety conscious.

The preparation of food in an oven requires temperatures that could cause severe burns. Before using this new appliance, carefully read and follow all instructions.

The California Safe Drinking Water and Toxic Enforcement Act of

1986 (Proposition 65)

requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm. In addition, businesses must warn customers of potential exposure to such substances.

Users of this appliance

are hereby warned that the burning of gas can result in low level exposure to some of the listed substances, including formaldehyde, benzene, soot and carbon monoxide. This is caused primarily from the incomplete combustion of natural gas or LP fuel. Properly adjusted burners will minimize incomplete combustion.

Exposure to these substances can also be minimized by properly venting the burners by opening a window or using a ventilating hood or fan.

2

U N I Q U E E L I T E 3 0 E & 3 6 E

Notice:

Never keep pet birds in the kitchen. Birds have a very sensitive respiratory system. Fumes released during cooking oil, fat, margarine or overheated non-stick cookware may be harmful or fatal to birds.

PROPER INSTALLATION:

Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the National Fuel Gas Code ANSI

Z223.1-latest edition, and the National Electrical Code ANSI/NFPA No. 70-latest edition. Install only per installation instructions provided in the literature package for this range. Be sure leveling legs are in place at the bottom corners of the range. If necessary, raise or lower the leveling legs at the base of the range by turning clockwise or counterclockwise to insure a level range.

Ask your dealer to recommend a qualified technician and an authorized repair service.

Have the technician familiarize you with the locations of the manual gas shut off valve and gas meter in the event it is necessary to shut off gas supply to the unit during an emergency.

The following situations may cause serious bodily harm, death or property damage.

TO REDUCE THE RISK OF TIPPING OF THE RANGE, THE RANGE

MUST BE SECURED BY A PROPERLY INSTALLED ANTI-TIP BRACKET

PROVIDED WITH THE RANGE. TO CHECK IF THE DEVICE IS

INSTALLED AND ENGAGED PROPERLY, CAREFULLY TIP THE

RANGE FORWARD. THE ANTI-TIP DEVICE SHOULD ENGAGE AND

PREVENT THE RANGE FROM TIPPING OVER. REFER TO THE

INSTALLATION INSTRUCTIONS PACKAGED WITH THE ANTI-TIP

BRACKET FOR PROPER ANTI-TIP BRACKET INSTALLATION.

Never leave children alone or unattended in the area where an appliance is in use

. They should never be allowed to sit or stand on any part of the appliance. Never leave the oven door open when the range is unattended.

Do not store items of interest to children in the cabinets above a range or on the backguard of a range.

Children climbing on the range to reach the items could be seriously injured.

Do not allow children to climb or play around the range.

The weight of a child on an open oven door may cause the range to tip, resulting in serious burns or other injury.

IMPORTANT:

Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

3

U N I Q U E E L I T E 3 0 E & 3 6 E

USER SERVICING: Do not repair or replace any part of the appliance unless specifically recommended in this owner’s guide.

All other servicing should be done only by a qualified technician. This will reduce the risk of personal injury and damage to the range.

Storage in or on appliance:

Flammable materials should not be stored in an oven, near surface burners or in the broiler section. This includes paper, plastic and cloth items, such as cookbooks, plastic ware and towels, as well as flammable liquids. Do not use the oven for storage. Do not store explosives, such as aerosol cans, on or near the range.

Remove the oven door from any unused range if it is to be stored or discarded.

Stepping, leaning or sitting on the doors or broiler section of this range can result in serious injuries and cause damage to the range.

The following situations could cause bodily injury or property damage

.

DO NOT TOUCH SURFACE BURNERS, AREAS NEAR THESE

BURNERS, OVEN BURNERS OR INTERIOR SURFACES OF THE

OVEN.

Both surface burners and oven burners may be hot even though the flame is not visible. Areas near surface burners may become hot enough to cause burns.

During and after use, do not touch, or let clothing or other flammable materials touch these areas until they have had sufficient time to cool. Among these areas are the range, surfaces facing the range, the oven vent openings and surfaces near these openings, oven door and windows.

NEVER use this appliance as a space heater to heat or warm the room.

Doing so may result in carbon monoxide poisoning and overheating of the oven.

Wear proper apparel.

Loose fitting or hanging garments should never be worn while using the appliance. Do not let clothing or other flammable materials contact surface burners or interior surfaces of the oven until they have had sufficient time to cool.

Never modify or alter the construction of the range.

Do not remove leveling legs, panels, wire covers, anti-tip brackets or any other permanent part of the product.

When heating fat or grease, watch it closely.

Fat or grease may catch fire if allowed to become too hot.

4

U N I Q U E E L I T E 3 0 E & 3 6 E

Do not use water or flour on grease fires.

Smother the fire with a pan lid, baking soda or use a dry chemical or foam-type extinguisher.

Operation of the Surface Burners.

When the burners are operated for the first time, a small amount of smoke may be generated due to tape residue or manufacturing lubrication.

THIS IS NOT DANGEROUS.

Operate the burners for about five minutes to rid the burners of this material before cooking.

Use only dry potholders.

Wet or damp potholders on hot surfaces could result in burns from steam. Do not let the potholder touch hot heating areas. Do not use a towel or other bulky cloth instead of a potholder.

Use proper flame size.

Adjust flame size so it does not extend beyond the edge of the cookware. The use of undersized cookware will expose a portion of the burner flame and may result in severe burns or direct contact and ignition of clothing. Also, proper relationship of cookware to burner will improve efficiency.

NEVER cover any slots, holes or passages in the oven bottom or cover an entire rack with materials such as aluminum foil.

Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard. Refer to the cleaning section of this manual for more information on the use of aluminum foil.

Placement of oven racks: Always place an oven rack in the desired location while the oven is cool.

If a rack must be moved when the oven is hot, use potholders and grasp the rack with both hands to reposition. Do not let potholders contact hot oven walls. Remove all cookware from the rack before moving.

Do not heat unopened food containers.

Build-up of pressure may cause the container to burst and result in injury.

Keep the oven vent duct unobstructed.

The oven vent is located along the bottom of the back guard. Touching the surfaces in the vent area when the oven is being operated may cause severe burns. Also, do not place plastic or heat-sensitive items on or near the oven vents. These items could melt or ignite. The range requires fresh air for proper burner combustion. Do not block the flow of air around the base or beneath the lower front panel of the range.

Use care when opening oven door: Stand to the side of the oven when opening the oven door.

Slowly open the door to allow hot air or steam to escape before removing or replacing food.

Know which knob controls each burner.

Place a pan of food on the burner before turning it on, and turn the burner off before removing the pan. Always turn to the full

5

U N I Q U E E L I T E 3 0 E & 3 6 E

LITE position when igniting top burners. Then adjust the flame size so it does not extend beyond the edge of the cookware.

Cookware handles should be turned inward and not extend over adjacent surface burners.

To reduce the risk of burns, ignition of flammable materials, and spillage due to unintentional contact with the cookware, the handle of a cookware should be positioned so that it is turned inward, and does not extend over adjacent surface burners.

Never leave the surface burners unattended.

Boilovers may cause smoking, greasy spillovers may catch fire or a pan which has boiled dry may melt.

Do not place hands between the spring tension hinge and the oven door frame when you are removing the oven door.

You could pinch your fingers.

Allow parts to cool to room temperature before touching or removing them from the range.

When a surface burner is first turned off, the burner and grate are hot enough to cause burns.

Clean the range regularly to keep all parts free of fat or grease which could catch fire.

Pay particular attention to the area underneath each surface burner. Exhaust fan ventilating hoods and grease filters should be clean. Do not allow fat or grease to accumulate. Greasy deposits in the fan could catch fire. Refer to the hood manufacturer’s instructions for cleaning.

Do not use a “cyclonic” range hood with this product.

Some range hoods circulate air by blowing downward toward the range top then drawing the air back up into the hood. This creates a “cyclonic” air wash that is designed for electric ranges only. A

“cyclonic” hood may cause the burners of a gas range to operate improperly.

Glazed cookware:

Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed cookware are suitable for rangetop service without breaking, due to the sudden change in temperature. Check the manufacturer’s recommendations for rangetop use.

Do not place plastic salt and pepper shakers, spoon holders or plastic wrappings on top of the range.

These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the flame.

Do not use a wok equipped with a metal ring that extends beyond the burner.

Because this ring traps heat, the burner and grate could be damaged. Also, the burner may not work properly, creating a carbon monoxide level above current health standards.

Do not clean the oven door gasket

. The door gasket is essential for a good seal. Care should be taken not to rub, damage or move the gasket.

6

U N I Q U E E L I T E 3 0 E & 3 6 E

Flexible Connectors: If the gas range/oven is connected to a gas supply with a metal flexible connector, move the range/oven with CAUTION for service or cleaning.

Flexible connectors are not intended for repeated bending. Do not allow cleaners to make contact with flexible connectors.

The connector and its fittings are designed for use only on the original installation and are not to be reused for another appliance or at another location. Connectors must comply with ANSI Z21.24.

It’s good practice for each household to have an appropriate fire extinguisher for use in the event of a house fire.

7

U N I Q U E E L I T E 3 0 E & 3 6 E

Dimensions and Clearances

All units must be installed in accordance to minimum rear and side wall clearance and clearances extended vertically above the cook top, specifics relating to minimum clearances are stated on the serial plate located at the back of the appliance near the gas inlet connection.

ANY OPENINGS IN THE WALL BEHIND THE UNIT AND IN THE FLOOR

UNDER THE UNIT MUST BE SEALED.

Note. Due to potential hazards it is recommended that storage cabinets

NOT

be installed above the cooking surface.

IN THE EVENT OVERHEAD CABINETS ARE INSTALLED, THE

MAXIMUM DEPTH OF CABINETS INSTALLED ABOVE COOKING TOPS

SHOULD BE 13”.

UGP 30E Specs

The range may be installed flush to the rear wall. You may install a non-combustible material on the rear wall above the range and up to the vent hood. It is not necessary to install non-combustible materials behind the range below the height of the counter top. The minimum distance from the side of the range above the counter top to combustible sidewalls must be at least 10 inches.

8

U N I Q U E E L I T E 3 0 E & 3 6 E

9

U N I Q U E E L I T E 3 0 E & 3 6 E

UGP 36E Specs

`

10

U N I Q U E E L I T E 3 0 E & 3 6 E

The bottom of the hood should be a minimum of 30” to 36” above the counter top. This would typically result in the bottom of the hood being 66” to 72” above the floor.

These dimensions provide safe and efficient operation of the hood.

11

U N I Q U E E L I T E 3 0 E & 3 6 E

UGP 30E and 36E Cut-out Specs

12

U N I Q U E E L I T E 3 0 E & 3 6 E

13

To reduce the risk of tipping the appliance by abnormal usage or improper door loading, the appliance must be secured by properly installing the anti-tip device packed with the appliance. To check if the device is installed and engaged properly, carefully tip the range forward. The anti-tip device should engage and prevent the range from tipping over.

If this range is removed for any reason,

(eg. service or cleaning), it must be replaced as outlined before placing the range back in operation.

Levelling a Free-Standing Range

All free-standing ranges must be level to obtain proper cooking results. The leveling legs should be screwed into the corner brackets. Place pan or measuring cup partially filled with water or a level on the oven rack. Adjust the leveling legs until the range is level. The top of the aside panels should be level with the counter top.

U N I Q U E E L I T E 3 0 E & 3 6 E

GAS CONNECTIONS (All Units)

NOTICE TO MASSACHUSETTS APPLIANCE DEALERS:

Be sure this document is included in all gas range appliances sold to consumers in the State of Massachusetts.

NOTICE: Massachusetts law requires the following:

Appliances must be installed by a licensed plumber or gas fitter.

Appliances must be connected with a three (3) foot (36” maximum length) flexible gas connector and

A “T” handle type manual gas valve in the gas supply line to the appliance

.

Have the dealer where you purchase your new range install it or have him recommend a qualified installer. Installation must conform with local codes. In the absence of local codes, the installation must conform with the National Fuel Gas

Code, ANSI Z223.1-Latest Edition in the U.S.A. or the CAN/CGA B149.1 or .2

Installation Codes in Canada.

The range should be connected to the supply line with 1/2-inch black iron pipe or a certified flexible type range connector. To prevent gas leaks, put an approved sealing compound, which is resistant to liquefied petroleum gases, on all threaded connections.

Important:

Do not apply pressure directly to the range manifold pipe when tightening supply connections. The manifold pipe should be held securely at the pressure regulator to prevent twisting. Hold the pressure regulator with a wrench during the tightening of the connection, or the manifold pipe may be twisted and split, and cause a dangerous leak.

The installation of ranges designed for manufactured (mobile) home installation must conform with the Manufactured Construction and Safety, Title 24 CFR, Part

3280, [formerly the Federal standard for Mobile Home Construction and Safety,

Title 24, HUD (Part 280)] in the U.S.A. or C.S.A. Standard CAN/CGA Z240.4.2 in

Canada or, when such standards are not applicable with local codes.

The installation of ranges designed for recreational vehicle installation must conform to state or other codes and in the absence of such codes with the standard for recreational vehicles ANSI A119.2.2–1982 in the U.S.A. or CAN/CGA Z240.4.2 in

Canada. The installation of appliances designed for recreational park trailers must conform to recreational park trailers, ANSI A119.5.

Note:

Check all piping connections in the unit for leaks. Never use an open flame to check for gas leaks using a soap solution with at recommend ratio of 75% water,

25% dish washing soap. It’s possible for connections made at the factory to leak, due to vibration encountered in transportation. Make certain you have checked them all, and repair any connections that leak.

14

U N I Q U E E L I T E 3 0 E & 3 6 E

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psig.

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.

Gas line shut-off valve

To reduce the possibility of gas leaks, apply Teflon tape or a thread compound approved for use with LP or Natural gases to all threaded connections.

Connect a ½” threaded pipe to the units regulator located at the back right of the unit. We suggest using a

½” female to 3/8” male flare adaptor on the end of the ½” threaded pipe.

Use a flexible appliance connector to connect your gas supply to the appliance. A 3 foot length is recommended for ease of installation but other lengths are acceptable.

Never use an old connector when installing a new range.

Check for leaks using a leak detector or soapy water with a recommended

Installation

ratio of 75% water, 25% dish washing soap

It is the responsibility of the installer to make certain that the range is properly adjusted at the time of installation. Situations caused by improper adjustments or improper installation are not covered under the warranty. Any expenses incurred due to such situations will not be paid by the manufacturer of the appliance.

Connecting gas to range

This range is designed to operate at a pressure of 4” of water column on natural gas

(NG) or 10” of water column on propane gas (LPG).

Make sure you are supplying your range with the type of gas for which it is designed.

This range comes equipped from the factory equipped for use with LPG

(propane).

This range is convertible for use on natural gas (NG) also. (Natural gas

15

U N I Q U E E L I T E 3 0 E & 3 6 E

orifices included in the packaging). When using this on NG gas, conversion must be made by a qualified NG installer before attempting to operate the range on that gas

For correct operation, the pressure of natural gas supplied to the regulator should be between 4” and 5” of water column. For LP gas, the pressure supplied must be between 10” and 12” of water column.

When checking for correct operation of the regulator, the inlet pressure must be at least 1” more than the operating -manifold- pressure as given above. The pressure regulator located at the back of the range manifold must remain in the supply line regardless of whether natural or LP gas is being used.

Regulator is only good for ½ psi (14” w.c.) so test pressure must not exceed ½” psi.

Shut off the main gas supply valve before removing the old range and leave it off until the new hook-up has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the range, the use of a CSA certified flexible metal appliance connector is recommended unless local codes require a hardpiped connection. Never reuse an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, use pipe joint compound resistant to LP or NG gases

(depending on set up) on all male -external- pipe threads.

1.

In an easily accessible location, install a service manual gas shut off valve. Be sure everyone operating the range knows where and how to shut off the gas supply to the range.

2.

When all connections have been made, be sure all range controls are in the off position and turn on the main gas supply valve. Check for gas leaks by using a soap and water solution. If a gas leak is present, shut off gas immediately, tighten all connections, and retest for leaks.

3.

Any opening in the wall behind the appliance and in the floor under the appliance shall be sealed.

16

U N I Q U E E L I T E 3 0 E & 3 6 E

After installation:

1.

Check ignition of cooktop burners.

2.

Check ignition of oven burner.

3.

Check ignition of broil burner

4.

Check ignition of griddle burner (36E model only)

5.

Check for gas leaks at all gas connections (using a gas detector, never a flame).

17

U N I Q U E E L I T E 3 0 E & 3 6 E

FIRST USE OF YOUR NEW RANGE & OVEN

When using the appliance for the first time, the oven and broiler burners should be turned on to burn off the manufacturing oils.

Conditioning the oven:

Conditioning will burn off any manufacturing residues and ensure that you get the best results right from the start.

1.

Insert all the shelves. See ‘Positioning the shelves’ for instructions.

2.

Turn on the ventilation hood above your range on high.

3.

Heat the empty oven at the highest temperature for:

30 minutes using BAKE

30 minutes using BROIL

There will be a distinctive smell while you are conditioning the oven. This is normal, but make sure the kitchen is well ventilated during the conditioning.

4.

Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.

Positioning the shelves:

Both the shelf racks (inside the oven) and oven shelves have safety stops at their front to prevent them from sliding out of the oven when pulled forward, and at their back to prevent the shelves from hitting the back wall of the oven.

18

U N I Q U E E L I T E 3 0 E & 3 6 E

Inserting the shelves:

1.

Hold both sides of the shelf firmly to keep it horizontal, with the front edge of the shelf closest to you.

2.

Insert the back edge of the shelf into the slots on the shelf racks.

3.

Lift the front edge of the shelf about 15 ˚ upwards, until the safety stops on the back of the shelf clears the safety stops on the shelf racks.

4.

Gently lower the shelf to horizontal and slide it all the way into the oven.

5.

Repeat these steps for the remaining shelves.

19

U N I Q U E E L I T E 3 0 E & 3 6 E

COOKTOP USE

Cooktop Burner Operation

Never leave the cooktop unattended when in use. Boil over causes smoking and greasy spills that may ignite.

Take care when deep-frying. Oil or fat can overheat and/or ignite very quickly, particularly on a high setting.

Make sure that all burner parts are properly in place. Incorrectly or incompletely assembled burners may produce dangerous flames. See

‘Replacing the Burner Parts’ in ‘Care and Cleaning’ on page 30.

Keep the burners clean. After a spill or boil over, make sure you clean the affected burners before using them again. Food residue may clog the igniter and the notches of the flame spreader, stopping the burner from functioning correctly. See ‘Care and Cleaning’ for instructions.

The top burner flame size should be adjusted so that is does not extend beyond the edge of the cooking utensil. As a matter of safety, it's recommended that you comply with these instructions.

A high flame on a surface burner is both inefficient and unsafe. The flame should always be adjusted so that it is no larger than the bottom of the pan. Fluctuations in flame size could be caused by pressure variations, improperly positioned burners, damage or debris.

Surface Burner Ignition

To light the top burners, push and turn the appropriate control knob counter clockwise to the “HI” position. You will hear a clicking noise - the sound of the electric spark igniting the burner. Once burner ignition has been achieved, turn the burner control knob to adjust the desired heat setting.

When one burner is turned to the “HI” position, the burner igniters will spark. Do not attempt to disassemble or clean around any burner while another burner is on. Do not touch any burner cap, burner base or igniter while the igniters are sparking.

20

U N I Q U E E L I T E 3 0 E & 3 6 E

Note: If the gas does not ignite within four seconds, turn off the valve and allow at least five minutes for any gas to dissipate.

In the event the electronic ignition system fails, the top burners and oven pilots can be lit by holding a lighted match near the burner head and turning the appropriate top burner knob to “HI” positon.

Simmer and Boil

A smaller flame setting will give the best simmer results. Small flames offer precise cooking performance for delicate foods, keeping food warm, melting chocolate or butter and for cooking that needs low heat for a long period of time.

A larger flame setting provides the maximum heat that is available on your range.

This setting should be used for higher temperature cooking such as stir fries, boiling water or cooking pasta.

Top Burner Height

21

U N I Q U E E L I T E 3 0 E & 3 6 E

Cooktop Surface

To prevent the cooktop from discoloring or staining, clean cooktop after each use, and wipe up acidic or sugary spills as soon as the cooktop has cooled.

The sealed burners of your range are not sealed to your cooktop and are designed to be removed. Boil overs or spills will not seep underneath the cooktop. The burners should be cleaned after each use.

Burner Grates

The grates must be properly positioned before cooking. Improper installation of the grates may result in scratches on the cooktop and/or poor combustion.

Oven Cooking Guidelines

Important:

Do not block the ducts on the rear of the range when using the oven. It is important that there is a continuous flow of hot air from the oven and fresh air into the oven burner. Avoid touching the vent opening or nearby surfaces during oven or broiler operation--they may become hot.

Keep oven door closed when using oven (bake or broil modes).

Never use aluminum foil to cover the oven shelves or to line the floor of the oven. This can trap heat, irreversibly damaging the enamel and may even cause fire.

Do not place water, ice, or any cookware or tray directly on the oven floor, as this will irreversibly damage the enamel.

Do not cover the slotted grid of the broil/roast pan with aluminum foil. This will catch grease and could catch fire.

Do not use plastic wrap or wax paper in the oven.

To ensure food safety, do not leave food in the oven for longer than two hours before and after cooking or defrosting. This is to avoid contamination by bacteria that could cause food poisoning. Take particular care during warmer weather.

According to the United Sates Department of Agriculture, DO NOT hold foods at temperatures between 40ºF to 140ºF more than 2 hours. Cooking raw foods below 275ºF is not recommended.

Never cover any slots, holes or passages in the oven bottom or cover an entire rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning.

Aluminum foil lining may also trap heat, causing a fire hazard.

22

U N I Q U E E L I T E 3 0 E & 3 6 E

Oven Function

Natural Airflow Bake occurs when heat is transferred into the oven from the bake burners in the bottom of the oven cavity. Heat is then circulated by natural airflow. This is a traditional bake setting.

Broiler

The upper broiler burner is located at the top of the oven. This burner sears the outside of broiled foods and sealing in juices.

Defrosting - Oven Function

To thaw uncooked frozen food, set the oven temperature to 100-150 ˚ F. Once thawed, cook the food immediately and do not refreeze. Prevent drips and spills from thawing food by ensuring that defrosting food is tightly wrapped in foil or is placed in oven-proof cookware.

Broiler Operation

Broiling is a method of cooking tender cuts of meat directly under the broiler in the oven.

Due to the high heat, it is normal and necessary for some smoke to be present during broiling, and therefore it is recommended to keep the oven door closed to maintain flavor, temperature and efficiency. When opening the oven door to check on the broiling process, do so as quickly as possible in order to preserve the cooking temperature and to prevent the control panel from the escaping heat.

For best results, it is recommended to use both a broil/roast pan and roasting rack. The rack helps to reduce smoking and splatter and promotes a uniform crust on the food by letting grease drip into the bottom of the pan, away from intense heat. To prevent food sticking to the rack during cooking, spray the rack with a light coating of non-stick cooking spray before placing food on it.

Broiler Operation - Preheating

Preheating is suggested when searing rare steaks. To preheat, turn the “OVEN” selector knob to the “BROIL” position. Wait for the broiler burner to become hot, approximately

2 minutes, and then place food beneath the broiler. Preheating is not necessary when broiling meat to well-done.

23

U N I Q U E E L I T E 3 0 E & 3 6 E

To Broil

When broiling, the heat radiates downward from the oven broiler for even coverage.

When broiling, use a roast pan with rack to allow fat and juices to drip down, away from the high heat of the oven broiler. DO NOT cover the roasting rack with foil, as the collected drippings could smoke or catch fire.

1.

Place a rack on a roasting pan and place the food on the rack. To prevent food sticking to the rack during cooking, spray the grid with a light coating of non-stick cooking spray before placing food on it.

2.

Arrange the interior oven shelves according to your recipe and place the broiler rack and pan assembly on the shelf. To assure even broiling, center the broiler pan and position directly under the broil burner. If preheating the broil burner first, position the broiler pan after the broil burner is preheated (see Broiler Operation - Preheating instructions above).

3.

Move selector switch to broil, turn “Broil” selector knob to High

Flame/Ignition to operate.

The broil indicator will remain on until the selector knob is turned to the off position or the temperature control cycles off.

Broil one side until food is browned; then turn and broil the other side to desired doneness. Season and serve. For safety, always pull the rack out to the “stop” position before turning or removing food.

For best results, it is recommended to use both a broil/roast pan and roasting rack, the rack helps to reduce smoking and splatter and promotes a uniform crust on the food by letting grease drip into the bottom of the pan, away from intense heat. To prevent food sticking to the rack during cooking, spray the rack with a light coating of non-stick cooking spray before placing food on it.

Broiler Guidelines

1.

Choose a suitable shelf position. To ensure that meat is cooked through rather than just browned on the outside, broil thick pieces of meat and poultry on shelf positions 2 or 3. Use shelf position 4 for thinner items that need less cooking time like steaks, chops, or hamburger patties.

2.

When finishing off meals by browning the top under the broiler, use metal or glass-ceramic cookware. Do not use heatproof glass or earthenware as these materials cannot withstand the intense heat of the broiler.

3.

To assure even cooking, center the pan and rack in the center of the oven, so that it is directly under the broiler.

24

U N I Q U E E L I T E 3 0 E & 3 6 E

UGP36E – Griddle Operation

Before using the griddle for the first time, clean it thoroughly with warm, soapy water to remove dust and any remaining manufacturing residue. Rinse with clean water and wipe dry with a clean, lint-free cloth.

Make sure that the grease trap is properly installed under the front edge of the griddle to neatly catch excess cooking oils and food residue.

Use the stainless steel cover to keep your griddle clean and dust free between uses.

Please note that the cover must be removed before turning the griddle on.

Griddle Cooking Guidelines:

Push and turn the griddle control knob counter-clockwise to the preferred cooking temperature.

Preheat the griddle for 10-12 minutes.

Butter or cooking oil should be added to the griddle surface to ensure a non-stick surface for efficient cooking.

The surface of the griddle is hot after use. Please allow sufficient time for the griddle to cool prior to cleaning.

Once cool, clean your griddle by scraping remaining cooking oils and residue into the grease trap. Remove the grease trap and the clean it thoroughly with warm, soapy water. Clean the griddle surface with warm, soapy water, rinse with clean water and wipe the griddle and grease trap dry with a clean, lint-free cloth.

25

U N I Q U E E L I T E 3 0 E & 3 6 E

OPERATION OF RANGE

UGP30E Control Panel

UGP36E Control Panel with Griddle

Control Panel Legend

Off

High Flame/Ignition

Off

Burner Position

Broil Burner

Bake Burner

Bake/Broil Toggle Switch

Oven Light

Griddle

26

U N I Q U E E L I T E 3 0 E & 3 6 E

Lighting the Top Burners/Griddle

1.

To obtain a flame more easily, light the burner before placing a cooking utensil on the burner grate.

2.

Decide which burner you’re igniting first using the screened diagram below the burner knob. The black dot indicates the position of the burner you’re igniting.

3.

To light a burner, press the burner knob in and turn counter clockwise to high flame/ignition position. You will hear the electronic ignition clicking as you continue to hold the knob down until the flame lights. Once the burner is lit, hold in for a few extra seconds to warm up the thermocouple so the electromagnet in the burner valve stays in the open position once you release.

4.

After lighting the flame, turn the control knob to adjust the flame size as required.

5.

If your lighting the griddle follow the same process, but watch the flame indicator above the knob go from the red into the green.

Lighting the Oven/Broiler

1.

Using the toggle switch, either select bake or broil burner.

2.

Depending on how long the gas line run is, it may take a while to light the oven pilot. It is suggested that you light a top burner first to ensure the gas is at the valve.

3.

Push in on oven or broiler knob, you will hear the electronic ignition. Hold until the oven or broiler pilot lights. Once lit, count to 10 then release. It should now stay lit; if not, repeat. You can tell when the bake or broil pilot is lit by viewing the flame indicator below the symbol.

4.

Once the oven or broiler pilot has been lit, lightly press in the oven or broiler control knob and turn counter clockwise to the desired temperature setting.

If you press the knob in too far during the ignition process, the knob will not turn.

Gently let up on the knob, and the thermostat shaft will release its safety key to let you rotate the control.

5.

When finished cooking, you may turn the oven or broiler control knob back to the “OFF” position. This will turn off the main oven or broiler burner and the pilot.

Note:

If you are using the oven or broiler for the first time, or if the oven or broiler has not been used in several days, it may take multiple attempts to successfully light.

If the ignitor pilot will not stay lit after 5 attempts, contact an authorized service technician.

27

U N I Q U E E L I T E 3 0 E & 3 6 E

If the oven or broiler pilot does not ignite and maintain the flame, check the following:

1.

The pilot burner has gone out

. Relight the oven or broiler pilot

2.

The pilot will not keep the flame safety probe heated

. Adjust the size of the pilot flame or the thermocouple connection at the thermostat may need to be tightened.

3.

The flame safety probe may not be properly located.

Locate the probe directly over the pilot burner. The end of the flame safety probe must be very close to the side of the burner right in front of the flame ports.

4.

The pilot burner is not in its proper position.

Make sure the rear of the burner is seated on the injector elbow and the front is bolted onto the burner support.

5.

The spark electrode is defective.

Contact an authorized service technician

If the batteries have grown weak and you need to use the oven or broiler before you are able to replace with fresh batteries, the oven or broiler can be lit manually.

Hot Oven Restart

If you turn off the oven but then decide to turn it back on before it has cooled to room temperature, the burner may not light properly. This is due to the thermostat still sensing “heated oven” and not allowing the maximum gas flow rate into the burner. After the burner lights, you may adjust the oven control to the desired temperature.

It is essential to maintain the gas pressure constantly at 10 inches water column pressure for ranges set for Propane (LP) Gas; and 4'' water column pressure for ranges set for Natural Gas (NG) to get proper pilot performance.

Note: Burner rates specified on the rating plate of your range apply for elevations up to 2,000 feet above sea level. For locations where altitudes are higher than 2,000 feet above sea level the b.t.u. rated input should be reduced four percent for each 1,000 feet higher than 2,000 feet above sea level. If this adjustment is necessary, you should contact a qualified serviceman. DO NOT ATTEMPT TO SERVICE THE RANGE

YOURSELF.

MOISTURE:

Moisture can have the same effect on the oven ignitor as the pilot flame. If sparking does not occur when the oven thermostat knob is turned on during the initial attempt to use or after several days of non-use, it COULD BE the result of moisture build-up in the ceramic sleeve of the oven electrode. This may happen in areas with high humidity, or if food having high water content is cooked.

This moisture can be driven out of the ignitor by lighting the pilot and operating the oven for a few minutes.

28

U N I Q U E E L I T E 3 0 E & 3 6 E

NEVER LEAVE THE CONTROL KNOBS IN ANY POSITION OTHER

THAN "OFF" IF THE IGNITORS OR BURNERS AREN'T WORKING

PROPERLY.

If the oven is working, to determine if moisture was the problem, wait a few minutes and attempt to light the oven by turning the oven control dial on. If sparking occurs at the oven electrode to ignite the oven pilot, and within sixty seconds ignites the oven burner, then moisture build-up was the problem. If the oven burner doesn't ignite within 60 seconds, turn the oven control off and call the serviceman.

.

Make certain the oven is cool when manually lighting oven or broiler pilot.

CARE & CLEANING THE RANGE

Cleaning guidelines

Read the “IMPORTANT SAFETY INSTRUCTIONS” on page 2 and these ‘CARE

AND CLEANING” guidelines before you start cleaning your range.

See the pages following for instructions on removing and replacing different parts of the range for cleaning and maintenance. To help you identify parts, see the range diagrams on pages 41-46.

Before cleaning or removing any part, make sure that all settings on the range and oven are set to “OFF”. Make sure all parts of the range and ovenware cool to the touch.

If you need to handle a warm or hot part of the range or oven (e.g. an oven shelf or a range grate) be sure to wear oven mitts and take extreme care to avoid burns or injury.

Do not use aerosol cleaners until the range has completely cooled. The propellant substance in these cleaners could catch fire in the presence of heat.

Do not let grease or food residue accumulate anywhere in or on the range. This will make future cleaning more difficult and may present a fire hazard.

29

U N I Q U E E L I T E 3 0 E & 3 6 E

Do not use any abrasive or harsh cleaners, cloths, scouring pads or steel wool on the exterior or interior of the range/oven. These will scratch and damage the appearance

Do not use a steam cleaner to clean any part of the range or oven.

Do not perform any cleaning or maintenance on parts not specifically listed in the chart below. If in doubt, contact Customer Care.

Do not lift the black grill and griddle frames off the cooktop.

Burner and Burner Caps

Check that the burner is turned OFF and allow it to cool. Lift off the burner cap. Use a stiff nylon brush or straight-ended paperclip to clear the notches of the burner. Wash them with a mild detergent in hot water, rinse, and dry. Replace the burner cap correctly.

Cooktop Surface

Clean the cooktop surface with a solution of mild detergent and warm water. Do not use harsh or abrasive cleaning agents, waxes, polishes, or commercial cooktop cleaners to clean the cooktop.

Treat stubborn, burnt-on grease and residue with the same solution of mild detergent and hot water - let it sit a few minutes and then wipe clean.

To protect the appliance finish, only use a sponge, soft cloth, fibrous or plastic brush, and nylon pad for cleaning.

Allow all components to dry thoroughly before using the cooktop.

Control Panel, Door Handles, Control Housing

Clean the control panel, door handles and control housing with a solution of mild detergent and warm water. Do not use harsh or abrasive cleaning agents, waxes, polishes, or commercial cooktop cleaners as they could damage the finish or printing.

Treat stubborn grease and residue with the same solution of mild detergent and hot water - let it sit a few minutes and then wipe clean.

To protect the appliance finish, only use a sponge, soft cloth, fibrous or plastic brush, and nylon pad for cleaning.

Dry all components thoroughly before using the cooktop.

30

U N I Q U E E L I T E 3 0 E & 3 6 E

Oven Side Racks and Oven Shelves:

Clean the oven side racks and oven shelves with a solution of mild detergent and warm water. To remove stubborn baked-on grease, apply soap and water, let it sit a few minutes and then scrub with a dampened, soap-filled, non-metal pad or brush, and wipe clean.

Apply a chrome cleaner with a damp sponge or cloth following manufacturer instructions.

Dry all components thoroughly before using the cooktop.

Bake and Broil Burners

Do not clean these parts. They self-clean during normal use.

Porcelain Surfaces

Clean the cooktop surface with a solution of mild detergent and warm water. Do not use harsh or abrasive cleaning agents, waxes, polishes, or commercial cooktop/oven cleaners to clean the cooktop.

Treat stubborn, burnt-on grease and residue with the same solution of mild detergent and hot water - let it sit a few minutes and then wipe clean.

To protect the appliance finish, only use a sponge, soft cloth, fibrous or plastic brush, and nylon pad for cleaning.

Allow all components to dry thoroughly before using the cooktop.

Oven Window

Clean all glass surfaces with a solution of mild detergent and hot water. Use a mild glass cleaner to remove fingerprints or smears.

Dry completely with a soft, lint-free cloth.

Oven Door Gasket

Take extreme care if you must clean or handle the oven door gasket, as the gasket is essential for a tight seal to ensure correct operating temperature. Any rubbing, scratching or displacement could damage the seal. If you need to remove any grease or residue from the gasket, proceed as follows:

1.

Dampen a sponge with clean hot water.

2.

Gently wipe off any residue with a blotting motion. Do not rub.

31

U N I Q U E E L I T E 3 0 E & 3 6 E

3.

Blot the area dry with a clean, soft towel and allow to fully dry before using the oven.

Stainless Steel Surfaces

Clean stainless steel surfaces with a solution of mild detergent and hot water.

Wipe away any remaining residue with a clean, damp cloth. Do not use any cleaning product containing chlorine bleach. Do not use harsh or abrasive cleaning agents or steel wool pads as these will damage the surface

Replacing the burner parts:

When replacing the burners, make sure that the two locating pins on the bottom of the brass flame spreader are properly aligned with the locating pin holes on the top of the simmer ring.

Incorrect alignment will produce a potentially dangerous flame and poor burner performance.

Replacing the oven light bulbs

To replace either of the oven light bulbs, release the glass cover on the lamp holder, and then replace the old bulb with a new bulb.

32

U N I Q U E E L I T E 3 0 E & 3 6 E

REMOVING OR REPLACING THE OVEN DOOR

Do not lift the oven door by its handle. Doing so may damage the handle or the door.

Before removing the door, make sure you have a flat, protected surface nearby on which to rest the oven door.

Take care when lifting or moving the oven door; it is heavy!

To remove the oven door, proceed as follows:

1.

Open the oven door fully.

2.

Open the levers fully on both sides of the door.

3.

Hold the oven door firmly on both sides and close it approximately halfway.

4.

Disengage the hinges and gently pull door free. Place it flat on a protected surface.

33

U N I Q U E E L I T E 3 0 E & 3 6 E

To replace the oven door, proceed as follows:

1.

Hold the door firmly in both hands.

2.

Holding the oven door at approximately half-way open, insert the hinge tongues into the slots, making sure that the notches on both sides drop into place as shown.

3.

Open the door fully.

4.

Fully close the levers on the left and right hinges as shown, then fully close the door.

34

U N I Q U E E L I T E 3 0 E & 3 6 E

HOW TO GAIN ACCESS TO THE BATTERY COMPARTMENT

Gaining access to the battery compartment:

1.

Locate the kick plate at the front bottom of the range

2.

The kick plate is clipped into place- simply lift up slightly and pull outwards.

3.

Pull away the kick plate. You now have access to the battery compartment

How to change the 9V volt batteries for oven lights and spark ignition

1.

Locate the battery holder which is fastened to the bottom right side of the range.

There are 2 x 9v batteries for the oven light and 2 x 9v batteries for the spark ignitions.

2.

Remove 9v volt batteries

3.

Ensure you replace with an Eveready or Duracell brand batteries, this will ensure a stronger spark and reduce the amount of times you will have to replace the batteries.

35

U N I Q U E E L I T E 3 0 E & 3 6 E

Troubleshooting Guide -

UGP Elite 30E & 36E Off Grid

Symptom

BURNERS   WILL  

NOT   LIGHT.

  

Possible Cause Solution

Burner   parts   or   igniters   may   be   wet,   dirty   or   misaligned.

 

Check   that   the   burner   parts   are   clean,   dry   and   correctly   assembled.

   Check   that   the   igniters   are   clean   and   dry.

  

FLAMES   DO  

NOT   BURN   ALL  

AROUND   THE  

BURNER   CAP.

 

BURNER  

FLAMES   ARE  

VERY   LARGE  

AND   YELLOW.

 

Burner   parts   may   be   dirty   or   misaligned.

 

See   “Care   and   Cleaning”   instructions.

 

Burner ports  

  bezel are  

  clogged.

 

Clean   burner   bezel   ring   ports   with   straightened   paper   clip,   needle,   or   wire.

 

Burner   ports   or   burner   caps   are   not   positioned   properly.

 

Remove burner  

  and bezel

 

  carefully and  

  caps.

re

 

‐ install  

Cooktop   is   being   operated   with   the   wrong   type   of   gas.

 

Ensure   that   the   type   of   cooktop   matches   the   gas   supply.

 

Check   installation, regulator,   or proper   gas.

 

  set  

  replace regulator

 

  for  

Regulator   is   not   installed,   is   faulty,   or   is   set   for   the   wrong   type   of   gas.

 

IGNITERS   ARE  

SPARKING   BUT  

BURNERS   ARE  

NOT   IGNITING.

 

Gas   shut ‐ off   valve   is   in   the   “OFF”   position.

 

Turn   shut ‐ off   valve   to   the   “ON”   position.

 

 

 

36

U N I Q U E E L I T E 3 0 E & 3 6 E

Symptom

BURNER   FLAME  

GOES   OUT   AT  

LOW   SETTING.

 

Possible Cause Solution

Low   gas   pressure.

  Contact   gas   company.

 

Air   intake   holes   around   burners   are   obstructed.

 

Remove   obstruction   from   air   intake   holes.

 

TOP   BURNER  

WILL   NOT   STAY  

LIT  

Failed   thermocouple   

THE   FLAMES  

HAVE  

SUDDENLY  

GONE   OUT.

 

Replace   thermocouple  

A   draft   or   spill   has   extinguished   the   flame.

 

Turn   the   burners   off,   cleaning   the   burners   and   sump   area.

  See   “Care   and   Cleaning”   for   instructions.

 

Once   clean,   reignite   top   burners.

 

 

NO   IGNITION

SPARK

 

 

 

 

THE   OVEN  

DOESN’T   WORK  

(NO   HEATING).

 

Dead   batteries   or  

 

 

 

  ignition   module   failed.

 

No   gas   supply   

Replace   batteries   with   new   batteries   and   attempt   ignition.

  If   there   is   still   no   spark   ignition,   the  

  cooktop   burners   can   still   be   used.

  

To   light   them:  

 

1.) Holding   a   lit   match   to   the   flame   spreader,   push   in   on   the   control   knob   and   turn   counter   clockwise   to   LIGHT.

 

 

2.) When   the   flame   is   burning   all   the   way   around   the   burner,   you   may   adjust   the   heat.

 

The   gas   supply   to   the   house   may   not   be   working   or   there   may   be   an   outage.

 

Contact   your   local   gas   supplier.

 

ONE   OF   THE  

OVEN   LIGHTS  

DOES   NOT  

COME   ON,   BUT  

THE   OVEN  

WORKS.

 

The   light loose.

 

  bulb   is  

The   light   bulb   has   blown.

 

See   instructions   for   “Replacing   the   oven   light   bulb”   in   section  

“Care   and   Cleaning”.

 

 

 

37

U N I Q U E E L I T E 3 0 E & 3 6 E

Symptom

CONDENSATION  

AROUND   OVEN  

(E.G.

  ON  

CONTROL  

PANEL   OR   TOP  

OF   OVEN  

DOOR.)  

Possible Cause Solution

Food   has   high   Condensation   is   normal.

  Simply   moisture   content   wipe   the   condensation   off   the   or   local   climate  

(temperature,   humidity)   is   contributing   to   condensation.

  control   panel.

  If   there   is   frequent   or   excessive   condensation,   make   sure   that   any   cabinetry   around   the   range   is   moisture   proofed.

 

STEAM   COMING  

FROM   OVEN  

VENTS   AT   THE  

BACK   OF   THE  

RANGE.

 

Moisture   from   food   evaporating   during   cooking.

 

This   is   normal,   especially   if   you   are   cooking   large   quantities   of   food.

 

 

FOODS   OVER ‐

COOKED   OR  

UNDER ‐

COOKED.

 

Incorrect   cooking   time   or   temperature.

 

•   Adjust   time,   temperature   or   rack   position.

   

“CRACKING”   OR  

“POPPING”  

SOUND   IS  

HEARD   COMING  

FROM  

RANGE/OVEN.

 

This   is   the   sound   of   metal   heating   and   cooling.

 

This   is   normal.

 

 

 

38

U N I Q U E E L I T E 3 0 E & 3 6 E

Wiring Diagram – UGP30E OF1

39

U N I Q U E E L I T E 3 0 E & 3 6 E

Wiring Diagram – UGP36E OF1

40

U N I Q U E E L I T E 3 0 E & 3 6 E

Parts Diagrams

UGP-30E OF1

41

U N I Q U E E L I T E 3 0 E & 3 6 E

UGP-36E OF1 – with Griddle

42

U N I Q U E E L I T E 3 0 E & 3 6 E

Parts List

UGP

30E

 

OF1

 

Item   #   Description  

1   Electrode  

2   Electrode  

3   Thermocouple  

4   Electrode  

5   cooking   grate  

6   Electrode  

7   Side   Panel,   Left  

8   Central   cooking   grate  

9   B   burn  

10   A   burn  

11   B   flame   ring  

12   A   Flame   ring  

13   B   flame   ring   base  

14   A   Flame   ring   base  

15   Orifice  φ 1.5MM

 

16   Orifice  φ 1.85MM

 

17   A   bottom   cup  

18   B   bottom   cup  

18   Aluminum   tube   A  

19   Drip   pan  

20   Aluminum   tube   B  

21   Decorate   box  

22   Oven   Lamp  

23   Oven   Side   Panel,   Left  

24   Oven   Rack   Support  

25   Oven   ceiling  

26   Oven   Rack  

27   Control   Panel   support  

28   Main   burner   valve  

29   Micro   switch  

30   Control   Panel  

31   Oven   Thermostat  

32   Fan/Light   Switch  

33   Indictor  

34   Bezel  

35   Option   Switch  

36   Broil   Pan   Cover  

37   Top   Burner   Knob  

43

Part   #  

UGP ‐ HX10090095 ‐ A0  

UGP ‐ HX10090094 ‐ A0  

UGP ‐ HX10050091 ‐ A0  

UGP ‐ HX10090093 ‐ A0  

UGP ‐ HX13010021 ‐ A0  

UGP ‐ HX10090092 ‐ A0  

UGP ‐ HX04020670 ‐ A0  

UGP ‐ HX13010025 ‐ A0  

UGP ‐ HX10010020 ‐ A0  

UGP ‐ HX10010076 ‐ A0  

UGP ‐ HX10010021 ‐ A0  

UGP ‐ HX10010077 ‐ A0  

UGP ‐ HX10010022 ‐ A0  

UGP ‐ HX10010078 ‐ A0  

UGP ‐ HX10050043 ‐ A0  

UGP ‐ HX10050084 ‐ A0  

UGP ‐ HX10010079 ‐ A0  

UGP ‐ HX10010023 ‐ A0  

UGP ‐ HX11020102 ‐ A0  

UGP ‐ HX04060680 ‐ A0  

UGP ‐ HX11020103 ‐ A0  

UGP ‐ HX04060569 ‐ A0  

UGP ‐ HX07040182 ‐ A0  

UGP ‐ HX04060538 ‐ A0  

UGP ‐ HX13030019 ‐ A0  

UGP ‐ HX04020392 ‐ A1  

UGP ‐ HX13030012 ‐ A2  

UGP ‐ HX20020107 ‐ A0  

UGP ‐ HX09010028 ‐ A0  

UGP ‐ HX17050018 ‐ A0  

UGP ‐ HX04020693 ‐ A0  

UGP ‐ HX09010029 ‐ A0  

UGP ‐ HX07020179 ‐ A0  

UGP ‐ HX07050180 ‐ A0  

UGP ‐ HX06010117 ‐ A0  

UGP ‐ HX14040009 ‐ A0  

UGP ‐ HX07020181 ‐ A0  

UGP ‐ HX04060555 ‐ A0  

U N I Q U E E L I T E 3 0 E & 3 6 E

Item   #  

Description  

38   Broil   Pan  

39   Door   Frame  

40   Door   hinge   receiver  

41   Baffle   plate   of   oven  

42   Door   hinge,   left  

43   Door   hinge,   right  

44   Door   Handle   Support,   Left  

45   Door   Handle   Support,   Right  

46   Door   Handle  

47   Door   Frame,   Outer  

48   U ‐ shape   Burner  

49   Unique   Logo  

50   Kick   Panel  

51   9V   Battery  

52   battery   holder  

53   back   panel  

54   backsplash  

55   Ignitor   1 ‐ 6  

56   Manifold  

57   Regulator  

58   Oven   Back   Panel  

59   Flash   Plate  

60   U ‐ shape   Burner   Assembly   

61   Oven   Side   Panel,   Right  

62   Flash   plate  

63   Right   side   plate  

64   Anti ‐ Tip   Bracket  

65   Adjustable   Leg   Support  

66   Adjustable   Leg  

44

Part   #  

UGP ‐ HX22990046 ‐ A0  

UGP ‐ HX04060554 ‐ A0  

UGP ‐ HX04010559 ‐ A0  

UGP ‐ HX05030017 ‐ A0  

UGP ‐ HX05030039 ‐ A0  

UGP ‐ HX05030040 ‐ A0  

UGP ‐ HX12020012 ‐ A0  

UGP ‐ HX12020013 ‐ A0  

UGP ‐ HX12010018 ‐ A0  

UGP ‐ HX04020519 ‐ A2  

UGP ‐ HX10020016 ‐ A1  

UGP ‐ HX08020009 ‐ A0  

UGP ‐ HX04020697 ‐ A0  

UGP ‐ HX07990178 ‐ A0  

UGP ‐ HX04020663 ‐ A0  

UGP ‐ HX04040525 ‐ A0  

UGP ‐ HX20010114 ‐ A0  

UGP ‐ HX07070185 ‐ A0  

UGP ‐ HX11050105 ‐ A0  

UGP ‐ HX09030009 ‐ A0  

UGP ‐ HX04050698 ‐ A0  

UGP ‐ HX04010527 ‐ A1  

UGP ‐ HX22990063 ‐ A0  

UGP ‐ HX04060539 ‐ A0  

UGP ‐ HX04030459 ‐ A0  

UGP ‐ HX04020670 ‐ A0  

UGP ‐ HX04040066 ‐ A0  

UGP ‐ HX20040092 ‐ A0  

UGP ‐ HX13030019 ‐ A0  

U N I Q U E E L I T E 3 0 E & 3 6 E

 

 

UGP

36E

 

OF1

 

 

Griddle

 

Item   #  

Description  

Electrode   1  

2  

3  

Electrode  

Thermocouple  

Electrode   4  

5  

6  

Electrode  

Griddle   Cover  

Griddle   handle   7  

8  

9   cooking   grate  

Side   Panel,   Left  

B   burn   10  

11  

12  

B   flame   ring  

A   burn  

B   flame   ring   base   13  

14  

15  

A   flame   ring  

A   flame   ring   base  

16  

17  

B   bottom   cup  

A   bottom   cup  

Aluminum   tube   A   18  

19  

20  

Drip   pan  

Aluminum   tube   B  

Oven   Lamp   21  

22  

23  

Oven   Side   Panel,   Left  

Oven   Rack   Support  

Oven   ceiling   24  

25  

26  

Oven   Rack  

Control   Panel   Support  

Main   burner   valve   27  

28  

29  

Control   Panel  

Fan/Light   Switch  

Indictor   30  

31  

32  

Bezel  

Option   Switch  

33  

34  

35  

Top   Burner   Knob  

Broil   Pan   Cover  

Broil   Pan  

36  

37  

38  

Door   hinge   receiver  

Door   Frame  

Baffle   plate   of   oven  

45

Part   #  

UGP ‐ HX10090086 ‐ A0  

UGP ‐ HX10090087 ‐ A0  

UGP ‐ HX10050091 ‐ A0  

UGP ‐ HX10090088 ‐ A0  

UGP ‐ HX10090089 ‐ A0  

UGP ‐ HX01010121 ‐ A1  

UGP ‐ HX12030005 ‐ A0  

UGP ‐ HX13010021 ‐ A0  

UGP ‐ HX01020669 ‐ A0  

UGP ‐ HX10010020 ‐ A0  

UGP ‐ HX10010021 ‐ A0  

UGP ‐ HX10010076 ‐ A0  

UGP ‐ HX10010022 ‐ A0  

UGP ‐ HX10010077 ‐ A0  

UGP ‐ HX10010078 ‐ A0  

UGP ‐ HX10010023 ‐ A0  

UGP ‐ HX10010079 ‐ A0  

UGP ‐ HX11020102 ‐ A0  

UGP ‐ HX24060586 ‐ A0  

UGP ‐ HX11020103 ‐ A0  

UGP ‐ HX07040182 ‐ A0  

UGP ‐ HX04060538 ‐ A0  

UGP ‐ HX13030019 ‐ A0  

UGP ‐ HX01020665 ‐ A0  

UGP ‐ HX13030010 ‐ A2  

UGP ‐ HX20020156 ‐ A0  

UGP ‐ HX09010028 ‐ A0  

UGP ‐ HX04020677 ‐ A0  

UGP ‐ HX07020179 ‐ A0  

UGP ‐ HX07050180 ‐ A0  

UGP ‐ HX14040009 ‐ A0  

UGP ‐ HX07020181 ‐ A0  

UGP ‐ HX22990039 ‐ A0  

UGP ‐ HX04060555 ‐ A0  

UGP ‐ HX04060554 ‐ A0  

UGP ‐ HX05030017 ‐ A0  

UGP ‐ HX04010684 ‐ A0  

UGP ‐ HX04020098 ‐ A1  

U N I Q U E E L I T E 3 0 E & 3 6 E

Item   #  

Description  

39   Door   hinge,   left  

40  

41  

Door

Door

 

 

Handle

Handle  

‐  Support,   Left  

Door   Frame,   Outer   42  

43  

44  

Door

Door

 

  hinge,

Handle

  right

 ‐ 

 

Support,   Left  

45  

46  

47  

U

U

 

Shape shape

Unique  

 

 

Burner

Burner

Logo  

 

 

Assy  

48  

49  

50  

U  

9V

Shape

 

Kick

Battery

 

  Burner

Panel  

 

 ‐  Orifice  

51  

52   backsplash

Grease  

Griddle  

 

Tray  

53  

54  

55  

Griddle

Griddle

 

  burner burner

Griddle   orifice  

 

  frame   Assembly  

56  

57  

58  

Back   Panel

Manifold  

Regulator  

 

59  

60  

61  

Infrared

Oven  

  nozzle

Back  

 

Panel  

Infrared   Flash   plate   62  

63  

64  

Oven

Flash

 

 

Side plate

  Panel

 

 

Side   Panel,   Right  

Right  

65  

66  

67  

Adjustable

Adjustable

 

 

Leg

Leg

 

 

Support  

46

Part   #  

UGP ‐ HX05030015 ‐ A0  

UGP ‐ HX12020012 ‐ A0  

UGP ‐ HX12010017 ‐ A0  

UGP ‐ HX04020510 ‐ A2  

UGP ‐ HX05030016 ‐ A0  

UGP ‐ HX12020013 ‐ A0  

UGP ‐ HX22990063 ‐ A0  

UGP ‐ HX10020016 ‐ A1  

UGP ‐ HX08020009 ‐ A0  

UGP ‐ HX07120190 ‐ A0  

UGP ‐ HX07990178 ‐ A0  

UGP ‐ HX04020668 ‐ A0  

UGP ‐ HX20010115 ‐ A0  

UGP ‐ HX04010093 ‐ A0  

UGP ‐ HX20990159 ‐ A0  

UGP ‐ HX22990064 ‐ A0  

UGP ‐ HX10020090 ‐ A0  

UGP ‐ HX05040051 ‐ A0  

UGP ‐ HX04060103 ‐ A2  

UGP ‐ HX11050104 ‐ A0  

UGP ‐ HX09030009 ‐ A0  

UGP ‐ HX05070036 ‐ A1  

UGP ‐ HX04060666 ‐ A0  

UGP ‐ HX04010527 ‐ A1  

UGP ‐ HX04060539 ‐ A0  

UGP ‐ HX04030683 ‐ A0  

UGP ‐ HX04020670 ‐ A0  

UGP ‐ HX20040092 ‐ A0  

UGP ‐ HX05010038 ‐ A0  

U N I Q U E E L I T E 3 0 E & 3 6 E

30” / 36” GAS RANGE

1 YEAR LIMITED WARRANTY*

 

Unique   Gas   Products   Ltd.

 

warrants   that   this   UNIQUE   range   is   free   from   defects   in   material   and   workmanship   under   normal   usage   and   service   under   the   following   terms:  

Parts   Warranty  

This   appliance   has   been   designed   for   domestic   household   use.

  If   properly   installed,   adjusted   and   operated   under   normal   conditions   in   accordance   with   printed   instructions,   it   will   satisfactorily   perform   the   functions   that   are   generally   expected   of   this   type   of   appliance.

  

If   the   appliance   fails   to   do   so   because   of   a   defect   in   material   or   workmanship   within   one   year   from   the   original   date   of   purchase:  

Unique   will   at   our   option,   repair,   exchange,   or   correct   by   other   means   Unique   consider   appropriate,   any   part(s)   Unique   finds   to   be   defective   except   for   the   surface   finish.

 

*Due   to   remote   locations,   it   is   the   customer’s   responsibility   to   bring   items   to   the   dealer   for   review

.

  Any   part(s)   replaced   or   repaired   will   be   warranted   only   for   the   balance   of   the   original   year.

 

Customer   is   responsible   for   labor.

  

Ownership  

This   Warranty   is   made   only   to   the   first   purchaser   (”original   purchaser”)   who   acquires   this   range   for   his/her   own   use   and   will   be   honored   by  

Unique   Gas   Products   Ltd.

 

and   by   the   Seller.

  Purchaser   must   retain   their   receipt   as   proof   of   purchase   date.

 

Warranty   Conditions  

This   warranty   does   not   apply   to   any   appliance   that   has   been   subjected   to   alterations,   misuse,   abuse  

(including   damage   by   foreign   agents   or   chemicals),   accident,   improper   installation   or   service,   delivery   damage,   or   other   than   normal   household   use   and   service.

 

This   UNIQUE   appliance  

must  

be   serviced   regularly   as   outlined   in   the   Owner’s   Manual.

 

Neither   Unique   Gas   Products   Ltd.

 

nor   the   selling   dealer   will   be   liable   for   direct   or   indirect   loss   of   foods   caused   by   failure   in   operation.

  In   case   of   damage,   the   owner   must   provide   proof   of   purchase,   Model,   and   Serial   Number   to   the   selling   dealer   or  

Unique   Gas   Products   Ltd.

 

This   warranty   is   LIMITED   STRICTLY   to   the   terms   indicated   herein,   and   no   other   expressed   warranties   or   remedies   thereunder   shall   be   binding   on   Unique.

 

Purchaser’s   Responsibilities  

The   purchaser   will   be   responsible   for   the   costs   of   any   service   calls   requested   to   demonstrate   or   confirm   the   proper   operation   of   the   appliance,   the   installation,   or   to   correct   malfunctions   in   the   appearance   created   by   the   operation   of   the   appliance   in   a   manner   not   prescribed   by   or   cautioned   against   in   the   use   and   care   instructions.

 

Model   and   Serial   Number  

The   appliance   model   number   and   serial   number   can   be   found   on   a   rating   plate   attached   on   the   floor   of   the   range,   at   the   front,   pull   out   the   broiler   rack   to   locate.

  The   purchaser   should   always   refer   to   the   model   and   serial   number   when   talking   to   or   contacting   the   dealer   from   whom   the   appliance   was   purchased.

 

Factory   Assistance  

If   the   purchaser   is   unable   to   locate   an   authorized   dealer/service   agent,   or   if   the   purchaser   does   not   receive   satisfaction   from   the   dealer,   they   may   contact   Unique   Gas   Products  ‐  Customer   Service   directly   at   Toll   Free   1 ‐ 877 ‐ 427 ‐ 2266   or   905 ‐ 827 ‐ 6154  

Unique   Gas   Products   Ltd,   2245   Wyecroft   Road,   Oakville,   Ontario,   Canada,   L6L   5L7  

Ph:   905 ‐ 827 ‐ 6154   Toll   Free:   1 ‐ 877 ‐ 427 ‐ 2266   Fax:   905 ‐ 827 ‐ 2027   www.UniqueOffGrid.com

  e ‐ mail:   [email protected]

 

47

advertisement

Related manuals

Download PDF

advertisement