Multifunctional Food Processor
Multifunctional Food Processor
Pour la version française veuillez consulter notre site de web
www.andrewjamesworldwide.com
Die deutsche Version finden Sie auf unsere Webseite
www.andrewjamesworldwide.com
Bitte finden Sie die deutsche Version dieser Bedienungsanleitung auf unserer
Homepage: www.andrewjamesworldwide.com
Safety Instructions



When using any electrical
appliance,
basic
safety
precautions should always be
followed including:
This appliance can be used by
children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge if
they have been given
supervision or instruction
concerning use of the
appliance in a safe way and
understand
the
hazards
involved. Children shall not
play with the appliance.
Cleaning
and
user
maintenance shall not be
made by children unless they
are older than 8 and
supervised.
Keep
the
appliance and its cord out of
reach of children less than 8
years old.
Always ensure the voltage on
the rating label corresponds
to the voltage in your home.

Check the power cord and
plug regularly for any
damage. If the cord or the
plug is damaged, it must be
replaced by a qualified
electrician or a service repair
centre. If in doubt please
contact our customer service
team.

The appliance is intended for
domestic use only. Industrial
or commercial use will void
the warranty. The supplier
cannot be held responsible
for injury or damage if the
appliance has been used for
anything other than its
intended use.

Incorrect operation and use
can damage the appliance
and cause injury to the user.

Do not use the appliance if it
has been dropped or
damaged in any way. If the
unit has been damaged take
the unit for examination and
or repair by an authorised
service agent.

Do not immerse or expose
the motor assembly, plug or
the power cord in water or
any other liquid for any
reason.

If the supply cord is damaged,
it must be replaced by the
manufacturer or by someone
who is suitably qualified to
avoid a potential hazard.

Do not let the cord hang over
the edge of a table or
counter. Ensure that the cord
is not in a position where it
can be pulled or tripped over
accidentally.

Do not allow the cord to
touch hot surfaces and do not
place the cord near hot gas,
electric burners or in a
heated oven.

Use of an extension cord with
this
appliance
is
not
recommended. However if it
is necessary to use an
extension cord, ensure that
the extension cord is equal to
or greater than the power
consumption of the appliance
to avoid overheating of the
appliance and extension cord.
Do not use any other
appliance on the extension
cord. Do not place the
extension cord in a position
where it can be pulled on by
children or animals or be
tripped over.

Always
operate
the
appliance on a smooth, even
and stable surface. Do not
place the unit on a hot
surface.

Always remove the plug of
the appliance safely. Do not
pull on the appliances cord
to remove the appliance plug
from the electrical socket.

Never handle or operate the
appliance with wet hands.

Do not immerse the motor
unit in water.
Appliance specific
instructions





use.

Never touch parts of the
appliance whilst they are
moving.

Refrain
from
putting
utensils or fingers inside
the lid opening.

Never
press
down
ingredients into the lid
opening with your hands.

Do not use the appliance
for hard ingredients such as
frozen meats, bones etc.

Always
ensure
the
appliance is turned off
before removing the lid and
any attachments.

Always remove the blades
before
removing
the
ingredients from the bowl.

Demonstrate care when
you are handling, fitting,
cleaning or removing the
blades from the food
processor.
safety
Only use the appliance for a
maximum of 1 minute.
Allow the appliance to cool
for
a
short
period
afterwards. After using the
appliance for more than 5 x
1 minute periods allow the
appliance to cool for 90
minutes.
Clean
all
parts
and
accessories that come into
contact with food before
first time use.
Never exceed the maximum
quantities stated on the
bowl.
Do not pour liquids hotter
than 30 ̊C into the food
processor.
Never leave the appliance
unattended while it is in

Never immerse the motor
unit in water or any liquid
for any reason.

Switch off the appliance and
remove all accessories
before cleaning.

Allow the jug / bowl to
warm
up
to
room
temperature before adding
warm liquids.

The appliance has an
incorporated
protective
device to protect the
appliance
against
high
temperatures.
If
the
temperature becomes too
high the appliance will
automatically turn off and
will resume operation once
the appliance has fully
cooled down (Approx. 15
minutes).
Before first time use
 Unpack the appliance and remove all
packaging.
 Disassemble the unit before first
time use.
 Wash all parts of the appliance
before first time use. Refer to
cleaning and maintenance.
Appliance components illustration
(6)
(4)
(5)
(2)
(3)
(1)
(7)
1. Power Unit
2. Drive Shaft
3. Bowl
5. Feed Tube
6. Plunger
7. Control dial
4. Lid
PLEASE NOTE: If you try and lock the bowl into place with the lid on, the lids locking
mechanism will prevent the bowl from locking into place and will damage the appliance.
If the lid is on, do not try and force the bowl into place. Simply remove the lid and place
the bowl onto the motor unit as normal.
Please make sure the lid is in line with the handle and locked into place.
(8)
(10
(11
(12
(9)
(8) - Cover / Sprinkler
(9) - Mill / Grinder Cup
(13
(10) - Lid Cover
(14)
(11) - Blender Lid
(12) - Blender Jug
(13) - Grinder / Blender Unit
(14) - Chopping Blade
(16)
(16) - Cutting Discs
(15)
b)
a)
c)
d)
a) Rasping disc / parmesan grater
c) Thick slicer / coarse shredder
b) Thin slicer / fine shredder
d) Julienne chopper
(15) - Kneading Tool
(18)
(17)
(20
(18) - Spatula
(17) - Citrus Juicer
(19
(21
(20) - Mini Chopper Attachment Blade
(19) - Twin Beater Whisk
(21) - Mini Chopper Bowl
Mini Chopper
Use the mini processor for pesto, salsa,
baby purees etc.
Do not continuously use the appliance for
more than 30 seconds on this function.
The motor should be allowed to cool
down for at least 1 minute. Only use for
a maximum of 3 times before letting the
machine cool down fully. The motor
should be allowed to cool down for at
least 30 minutes before the next
operation.
Assembly
1. Place the drive shaft (2) on to the
power unit (1).
2. Put the bowl (3) onto the drive shaft
(2) rotating clockwise until it fits into
the power unit (1). Please note: Due to
a safety locking system the food
processor will not work until the
components are locked in place
correctly.
3. Place mini chopper bowl (21) inside
the bowl (3) and on top of the drive
shaft (2) followed by the mini chopper
blade (20) applying pressure to ensure
it is correctly fixed.
4. Place the bowl cover (4) on to the top
of the bowl (3) and turn clockwise until
it locks into place.
5. It is recommended to start the speed
setting on low then increase the
speed setting. Place food down the
feeding tube (5), use plunger (6) to do
so.
6. Turn off appliance when finished.
Disassembly
1. Switch off the appliance.
2. Remove the bowl cover (4) by
clasping the feeding tube and rotating
the bowl cover anti-clockwise to
unlock it from the bowl (3).
3. Remove mini chopper blade (20) and
mini chopper bowl (21) to empty
ingredients.
4. Unlock the bowl (3) from the power
unit (1) by rotating it clockwise using
the handle.
5. Remove the drive shaft (2) and clean
the appliance as instructed in the
cleaning section of the manual.
Cutting Discs
a) Use this disc for very fine grating such
as parmesan cheese and for rasping
vegetables like carrots
of the bowl (3) by aligning the lid of
the cover with the handle of the jug
and turned clockwise so it clicks into
place.
b) Use this disc one way up to create thin
slices, and use with the grater side up
for fine shredding of foods such as
potatoes, vegetables and cheese
5. Choose which size feed tube you want
to use (5). The plunger contains a
smaller feed tube for processing
individual items or thin ingredients
(this must be used for cheeses)
c) Use this disc one way up to create
thicker slices, and with the grater side
up for more coarse shredding
6. To use the small feed tube – first put
the large pusher inside the feed tube.
d) Use the Julienne disc to slice food such
as hard vegetables into thin sticks
Do not use this function for more than 3
minutes at a time. The motor should be
allowed to cool down for at least 30
minutes before the next operation.
Assembly
1. Place the drive shaft (2) onto the
power unit (1)
2. Put the bowl (3) onto the drive shaft
(2) rotating clockwise until it is aligned
with the locking system on the power
unit (1). Please note: Due to a safety
locking system the food processor will
not work until the components are
locked in place correctly.
3. Holding by the center grip on the disc,
place one of the discs onto the drive
shaft (2) with the appropriate side
facing upwards.
4. Place the bowl cover (4) on to the top
7. To use the large feed tube – use both
pushers together.
8. Turn the food processor on (7) and
guide the ingredients through the
feeder (5) with the food plunger (6).
9. Turn off appliance when finished and
clean as instructed in the cleaning
section of the manual.
Chopping
Assembly
Blade
/
Kneading
Tool
shaft (2) until it reaches the base of
the bowl(3).
The chopping blade is the most versatile
of all the attachments and the length of
the processing time will determine the
texture achieved. For coarser texture use
the pulse control.
4. Place the bowl cover (4) on the bowl
(3), aligning it with the locking
system. Turn the bowl cover
clockwise until the lid locks into place
at the top of the handle.
To ensure the long life of your machine,
do not use continuously for more than 3
minutes on this function. The motor
should be allowed to cool down for at
least 30 minutes before the next
operation.
5. Turn off appliance when finished.
Use the chopping blade for cake and
pastry making, chopping raw and cooked
meat, vegetables, nuts, pate, dips,
pureeing soups and to also make crumbs
from biscuits and bread. It can also be
used for yeasted dough mixes. Use the
kneading tool for kneading dough,
particularly yeasted mixes.
2. Turn the bowl (3) anti-clockwise until
it comes free of the locking system.
Assembly
1. Place drive shaft (2) into the centre of
the power unit (1). Ensure it is firmly in
place.
2. Guide the bowl (3) over the drive shaft
(2) rotating clockwise until it is aligned
with the locking system on the power
unit (1). Please note: Due to a safety
locking system the food processor will
not work until the components are
locked in place correctly.
3. Place the blade (14/15) over the drive
Disassembly
1. Unlock the bowl cover (4) by turning
it anti-clockwise and remove the
blade (14/15).
3. Clean as instructed in the cleaning
section of the manual.
Citrus Juicer
Assemble the appliance according to the
diagram
Use the citrus press to squeeze the juice
from citrus fruits (e.g. oranges, lemons,
limes and grapefruits).
To ensure the long life of your machine,
do not use it continuously for more than
3 minutes on this function. Only use for a
maximum of 3 times before letting the
machine cool down fully. The motor
should be allowed to cool down for at
least 30 minutes before the next
operation.
To use the citrus press
1. Place drive shaft (2) into the centre of
the power unit (1). Ensure it is firmly in
place.
2. Guide the bowl (3) over the drive shaft
(2) rotating clockwise until it is aligned
with the locking system on the power
unit (1).
3. Fit the filter part of the citrus juicer
(17) into the bowl (3) and turn
clockwise until it locks in place (it will
rest on top of the processor bowl)
Please note: The citrus press will not
operate if the sieve is not locked
correctly.
4. Fit the squeezer part of the citrus
press in the centre of the filter part
turning until it drops down into place
and can no longer be turned.
5. Cut the fruit in half. Then switch on
the processor (7) and place the fruit
onto the squeezer part of the citrus
press attachment (17), pushing down
gently to squeeze out the juice. Start
on a low speed and increase if
necessary.
6. Turn off appliance when finished.
Disassembly
1. To remove the attachment rotate the
citrus juicer (17) anti-clockwise to
unlock it from the bowl.
2. Turn the bowl (3) anti-clockwise until
it comes free of the locking system.
3. Clean as instructed in the cleaning
section of the manual.
Twin beater whisk attachment
Use for light mixtures only e.g. egg
whites, cream, evaporated milk and for
whisking eggs and sugar for fatless
sponges. Heavier mixtures such as fat
and flour will damage the attachments if
used. Do not use the balloon beater to
prepare cake mixtures with butter or
margarine or to knead dough. Use the
kneading accessory for these jobs.
To ensure the long life of your machine,
do not use continuously for more than 3
minutes on this function. The motor
should be allowed to cool down for at
least 30 minutes before the next
operation. Do not fill the bowl beyond
the MAX indication.
Assembly
1. Place drive shaft (2) into the centre of
the power unit (1). Ensure it is firmly in
place.
2. Guide the bowl (3) over the drive shaft
(2) rotating clockwise until it is aligned
with the locking system on the power
unit (1).
3. Clip the whisks into the whisk
attachment (19) by inserting the two
prongs into the cross-shaped slots.
4. Place the food you wish to whisk into
the bowl (3)
5. Attach the whisk attachment (19) to
the drive shaft (2) firmly and apply
pressure to ensure it is correctly fixed.
6. Place the bowl cover (4) on the bowl
(3), aligning it with the locking system.
Turn the bowl cover clockwise until
the lid locks into place at the top of
the handle.
7. It is recommended to start the speed
setting on low then increase the
speed setting (7).
8. Turn off appliance when finished.
Disassembly
1. Switch off the appliance.
2. Remove the bowl cover (4) by
clasping the feed and rotating the
bowl cover clockwise to unlock it
from the bowl (3).
3. Unlock the bowl (3) from the power
unit (1) by rotating it anti- clockwise
using the handle.
4. Lift off the twin beat whisk (19) and
empty out ingredients.
5. Remove the drive shaft (2) and clean
the appliance as instructed in the
cleaning section of the manual.
Mill
Use the mill function for grinding herbs,
nuts and coffee beans.
To ensure the long life of your machine,
do not use the machine continuously for
more than 1 minute at a time. The motor
should be allowed to cool down for at
least 30 minutes before the next
operation. Don’t process spices – they
may damage the plastic. The machine
won’t work if the mill is fitted incorrectly.
Use for dry ingredients only.
Assembly
1. Put your ingredients into the jar (9). Fill
it no more than half full.
2. Fit the silicone sealing ring into the
blade unit (13).
3. Turn the blade unit (13) upside down.
Lower it into the jar (9), blades facing
down.
4. Screw the blade unit (13) onto the jar
(9) and tighten until arrow at the base
of the jar (9) is aligned between the 2
bars on the blade unit (13).
5. Place the blade unit (13) onto the
power unit (1) and rotate clockwise
until it is aligned with the locking
system on the power unit (1).
6. Switch on to maximum speed or use
the pulse control.
7. Turn off appliance when finished.
Disassembly
1. Switch off the appliance.
2. Rotate the blade unit (13) anticlockwise until loose from the power
unit and remove it.
3. Turn the blade unit (13) upside down
so that the blade is facing downwards
and screw the jar (9) anti-clockwise to
remove.
4. Empty out the ingredients or replace
the blade unit (13) with the sprinkler
lid (8) to sprinkle ingredients.
5. Clean the appliance as instructed in
the cleaning section of the manual.
Please note: The sprinkler lid is not
airtight.
Blender
Use the blender for pasta sauces, soups,
milkshakes etc.
Do not use the machine continuously for
more than 30 seconds on this function.
The motor should be allowed to cool
down for at least 1 minute. Only use for
a maximum of 3 times before letting the
machine cool down fully.
 DO NOT PUT HOT LIQUIDS INTO THE
BLENDER AS THIS WILL CAUSE THE JUG
TO CRACK. THE TEMPERATURE OF
FOODS ADDED TO THE BLENDER
SHOULD NOT EXCEED 30°C ABOVE THE
TEMPERATURE OF THE ROOM.
 Allow the jug to warm up to room
temperature before adding warm
liquids.
Assembly
1. The plastic jug (12) does not come fully
assembled, fit the silicone sealing ring
into the blade unit (13).
2. Place the plastic jug (12) onto the
blade unit (13) and tighten until arrow
at the base of the Jug is aligned
between the 2 bars on the blade unit
(13).
3. Attach the blender to the power unit
(1) by rotating clockwise until it is
aligned with the locking system on the
power unit (1).
4. Remove the lid (11) by screwing anticlockwise, place in the ingredients and
replace the lid (11) back on the jug
(12) by reversing the action.
5. Turn the control dial to your required
setting (7).
Disassembly
1. Remove the jug (12) from the power
unit (1) by rotating anti-clockwise
using the handle.
2. Lift the lid (11) off the appliance by
screwing anti-clockwise and pour out
the ingredients.
3. Removed the blade unit (13) from the
plastic jug (12) by screwing anticlockwise
4. Clean as instructed in the cleaning
section of the manual.
Caramelised Onion Tart
Ingredients
340g short crust pastry
4 red onions, skinned and halved
4 eggs
200ml milk
120g Gruyere cheese
1 tbsp. oil
Salt and pepper
Attachment: Cutting discs (16)
Method
1. Preheat oven to 190°C/Gas mark 5.
2. Roll out pastry to fit a 20cm quiche tin.
Place the pastry in the tin and push in
to the sides. Trim the pastry around
the edge of the tin.
onion is sliced, turn off
Multifunctional Food Processor.
the
5. Heat 1 tbsp. of oil in a frying pan.
Sauté the onion in the frying pan until
soft and caramelised. Allow to cool
slightly then place on the pastry base.
6. Beat together eggs and milk and
season well with salt and pepper.
Pour over the onions on the pastry
base.
7. Attach the fine shredding disc (b) to
the drive shaft.
Turn the
Multifunctional Food Processor on to
minimum speed and use the food
pusher to guide the cheese down the
feeder. When all of the cheese is
grated, turn off the Multifunctional
Food Processor. Sprinkle the grated
cheese over the top of the tart
evenly.
3. Cut a circle of greaseproof paper just
larger than the tin and place on top
the pastry. Pour in baking beans or
dried peas/beans and bake in the oven
for 10mins. Remove the pastry from
the oven, take the greaseproof paper
and baking beans off the pastry then
put the pastry back in the oven for a
further 5 minutes.
8. Place in the oven for 35-40 minutes
until the cheese is golden brown and
the filling is firm.
4. Attach the thick slicing disc (c) onto
the drive shaft. Skin and halve the
onions. Turn the Multifunctional Food
Processor on to minimum speed and
use the food pusher to guide the onion
down the feed tube. When all of the
200g butter
9. Allow to cool slightly before serving.
Chicken Liver Pate
Ingredients
400g chicken livers, washed
2 shallots, finely chopped
2 cloves of garlic, finely chopped
75ml brandy
110ml double cream
7g yeast
1/2 tsp salt
55g sundried tomatoes, jarred
1/2 tsp black pepper
1 tbsp. oil from sundried tomatoes
1 tsp thyme
110ml warm water
Attachment: chopping blade (14)
Attachment: kneading tool (15)
Method
Method
1. Cut the livers into small pieces
(approx. 1.5cm). Heat a knob of
butter in a frying pan.
1. Add salt, flour and yeast to the 1.5l
bowl. Using kneading tool (15), mix
on minimum for 30 seconds.
2. Sauté shallot and thyme until soft.
2. Add water, sundried tomatoes and
oil. If the sundried tomatoes are
large, chop into 3 pieces.
3. Add chicken livers to the pan and
sauté until brown on the outside but
pink on the inside, then pour contents
of the pan into the food processor.
4. Add brandy to the pan and boil until
reduced. Pour into food processor.
5. Add double cream, salt, pepper and
140g of butter to the food processor
and blend until smooth.
6. Push the pate through sieve into a
serving dish/ramekins, leave to cool.
7. Melt the remaining butter and pour
over the pate. Cover and cool. Once
cooled, store in the fridge until
serving.
Tomato Bread
Ingredients
250g strong white bread flour
1 tsp salt
3. Mix for 1-2 minutes until dough is
formed.
4. Remove dough and place in a bowl
covered with cling film. Stand the
bowl in a warm place for
approximately 60 minutes, until the
dough has doubled in size.
5. Knead the dough by hand for 2
minutes. Shape and place in a tin,
cover and stand in a warm place until
the dough has doubled in size.
6. Preheat oven to 180°C/Gas mark 4.
7. Place the dough in the oven for 35
minutes.
Tip
To check the bread is cooked, tap the
base of the bread with your fingers, if
hollow sounding, it is ready.
Chunky Pesto
Ingredients
Bunch of fresh basil
3 cloves of garlic
3 tbsp. parmesan cheese
75g sunflower seeds
6 tbsp. olive oil
Attachment: Mini Chopper (20/21)
Method
1. Place garlic cloves, basil and 2 tbsp. of
olive oil into the mini chopper bowl.
Pulse until the garlic is fine.
2. Add grated parmesan cheese and the
rest of the olive oil. Pulse until
ingredients are combined.
3. Add the sunflower seeds. Pulse once
last time. Don’t pulse too much here
as you want the sunflower seeds to
remain chunky.
Serving tip
Stir through cooked gnocchi and sprinkle
with extra parmesan for an Italian treat.
St Clements Juice
Ingredients
8 oranges and 1 lemon
Sparkling water
Attachment: Citrus press (17)
Method
1. Halve 8 oranges. Place on the citrus
press and turn the Multifunctional
Food Processor to minimum. Hold
until all the juice has been extracted.
Continue until all the oranges are
juiced.
2. Halve a lemon and place on the citrus
press until the juice is extracted.
Continue with the other half.
3. Pour juice into a glass and top up with
sparkling water.
Meringue
Ingredients
6 egg whites
170g caster sugar
150g icing sugar
Attachment: Twin Beater Whisk (19)
Method
1. Preheat the oven 110°C/Gas mark ¼.
2. Pour egg whites into 1.5l bowl and
whisk on medium until the mixture
forms soft peaks.
3. Turn the Multifunctional Food
Processor onto high and add sugar a
desert spoonful at a time. Follow the
same procedure for adding the icing
sugar.
4. Once the icing sugar and caster sugar
is incorporated, gently scrape out and
shape the meringue onto a tray lined
with greaseproof paper. Choose
whether you want a large meringue or
individuals at this stage.
5. Place in the preheated oven for one
hour until crispy.
6. Turn the oven off and leave the
meringue to dry for a further hour.
Tip
For a chocolate ripple meringue, pour 25g
of cocoa into the Multifunctional Food
Processor once all the sugar is
incorporated and whisk for 10 seconds.
Ingredients list
Reference for processing size and time
Tool / Attachment
Function
Speed
Maximum
capacities
Max running
time
Chopping Blade
Grinding meat
2
500g meat
30sec
Chopping vegetables
1-2
Making stuffing: cut meat first, then
vegetables
2
Dough Tool
Making / kneading dough
2
500g flour
280ml water
60sec
Cutting Discs
Slicing/ shredding/ julienne slicing /
grating cheese and vegetables
1-2
1200ml
60sec
Blender
Making milk shake, smoothies, soup
etc.
1-2
1200ml
60sec
Citrus Press
Citrus fruit juicing
1
1200ml
60sec
Mill
Grinding nuts, herbs and coffee beans
2
200g
30sec
Twin Beater Whisk
Whisking egg whites
2
8 egg whites
30sec
Cleaning
 Switch off and always unplug the
processor from the power outlet
before cleaning the appliance.
 Clean the power unit with a soft
slightly damp cloth. Do not put it
under running water and do not
submerge it in water or any other
liquids.
 Do not immerse the blade unit in
water.
 All accessories can be washed by hand
or in the dishwasher, for hand washing
use tepid water and normal detergent.
For dishwasher cleaning always place
accessories in the upper part of the
dishwasher making sure the water
never exceeds a temperature of 30 ̊C.
 Do not use chemical or abrasive
washing up liquids.
 Store the appliance in a dry area,
preferably in its original box.
 Some foods may discolour the plastic.
This is perfectly normal and wont
harm the plastic or affect the flavour
of your food. Rub with a cloth dipped
in vegetable oil to remove the
discolouration.
UK and EU Guarantee
Your new Andrew James product comes
with a 24 month guarantee and a 2 year
fixed warranty, effective from receipt
confirmation. Your receipt or order
number is required as proof of purchase
date so it is imperative that you keep it
safe. This guarantee only applies if the
item has been used solely for the use
intended, and all instructions have been
followed accordingly. Please note this
product is only for domestic use only and
is not for commercial use.
Abuse of your product will invalidate the
guarantee. Returned goods can only be
accepted if repackaged properly within
the original colour product box, and
presented with the original receipt of
sale / order number. This does not affect
your statutory rights.
Returned products must be cleaned and
returned to us in as close to delivery
condition as possible.
If your product develops a problem
within the first 12 months of the fixed
warranty, we will pay all shipping costs to
have it returned to us. After 12 months
the customer will be liable for the cost of
returning the product to us. We will then
pay to have the repaired/replaced item
shipped back to the customer.
If you wish to return your item for a full
refund, you have the right to do so within
the first 7 days. For our returns policy
please go to:
www.andrewjamesworldwide.com
Customers are responsible for any taxes
applied to our products when they are
shipped outside of the EU.
All of our prices are inclusive of VAT.
Once a product has been returned to us,
we will aim to repair or replace it within
30 days of receipt.
The guarantee does not cover any defect
arising from improper use, damage, build
-up of lime scale or repair attempts made
by third-parties. Also, the guarantee does
not cover normal wear and tear of
individual parts.
Class II Double Insulated Products
Electrical Information
Always ensure the voltage on the rating
label corresponds to the power supply
where the product is being used.
Class II double insulation. This
tool
is
double
insulated
therefore no earth connection is
required.
Precautions should be followed for safe
cable management and connection to the
power supply
If a new mains plug needs to be fitted
follow the fitting instructions supplied
with good quality BS1363A plugs. If in
doubt consult a qualified electrician or
appliance repair agent.
 Safely dispose of the old plug.
 Connect the brown lead to the live
terminal “L” in the new plug.
 Connect the blue lead to the neutral
“N” terminal.
Warning! For double insulated product
no connection is made to the Earth
terminal.
Recommended fuse: 13A
If an extension cable is required, a 2 core
or 3 core (earthed) extension can be
used. To avoid overheating the extension
cable should be rated no less than 13A
and be fully unwound before use.
Do not attempt to modify electrical plugs
or sockets or attempt to make an
alternative connection to the electrical
supply.
Disposal of the appliance
Waste Electrical & Electronic Equipment
(WEEE) Waste & Recycling
Disposal of Electrical and Electronic
Waste
Non-household waste. This product must
not be disposed of together with
ordinary household waste.
Separate collection of used products,
batteries and packaging allows the
recovery and recycling of materials. Reuse of materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local authorities, retailers and collection Contact details
organisations may provide for separate
Andrew James UK LTD
collection of elec-trical products, batteries
Unit 1
and packaging.
P C Henderson Premises
Bowburn North Industrial Estate
Bowburn
Co Durham
DH6 5NG
Customer Service / Technical Support
Telephone: 0844 335 8464
Email:
[email protected]
e.com
Web: www.andrewjamesworldwide.com
Twitter: @andrewjamesltd
Facebook: Andrew James
Copyright Andrew James
Pour la version française de ce notice
veuillez
visiter
notre
site:
www.andrewjamesworldwide.com
Bitte finden Sie die deutsche Version
dieser Bedienungsanleitung auf unserer:
www.andrewjamesworldwide.com
AJ000233
01/2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement