LG | 32LA62**-Z* | User's Manual | LG 32LA62**-Z* User's Manual

Internal Use Only
North/Latin America
Europe/Africa
Asia/Oceania
http://aic.lgservice.com
http://eic.lgservice.com
http://biz.lgservice.com
LED TV
SERVICE MANUAL
CHASSIS : LD33B
MODEL : 32LA62**
32LA62**-Z*
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL67727123 (1306-REV01)
Printed in Korea
CONTENTS
CONTENTS . ............................................................................................. 2
SAFETY PRECAUTIONS ......................................................................... 3
SERVICING PRECAUTIONS..................................................................... 4
SPECIFICATION........................................................................................ 6
ADJUSTMENT INSTRUCTION............................................................... 14
BLOCK DIAGRAM ................................................................................. 21
EXPLODED VIEW .................................................................................. 22
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-2-
LGE Internal Use Only
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 MΩ and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-3-
LGE Internal Use Only
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions
on page 3 of this publication, always follow the safety precautions. Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug
or other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an explosion hazard.
2. Test high voltage only by measuring it with an appropriate
high voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10 % (by volume) Acetone and 90 %
(by volume) isopropyl alcohol (90 % - 99 % strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication
of contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks
are correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors
and semiconductor “chip” components. The following techniques
should be used to help reduce the incidence of component damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent
potential shock reasons prior to applying power to the unit
under test.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder
ES devices.
4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or
comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will
be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within
the range or 500 °F to 600 °F.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500 °F to 600 °F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500 °F to 600 °F)
b. First, hold the soldering iron tip and solder the strand
against the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
-4-
LGE Internal Use Only
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by
gently prying up on the lead with the soldering iron tip as the
solder melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing
the IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close
as possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and
if necessary, apply additional solder.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the
good copper pattern. Solder the overlapped area and clip off
any excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the
lead of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-5-
LGE Internal Use Only
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LED TV used LD33B
chassis.
3. Test method
2. Requirement for Test
1) Performance: LGE TV test method followed
2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
Each part is tested as below without special appointment.
1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C
2) Relative Humidity: 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 20 minutes prior to
the adjustment.
4. Model General Specification
No.
1
Item
Market
Specification
Remarks
DTV & Analog (Total 37 countries)
DTV (MPEG2/4, DVB-T) : 29 countries
Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Luxemburg,
Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia,
Estonia, Lithuania, Poland, Portugal, Romania, Albania,
Bosnia, Serbia, Slovakia, Beralus
EU(PAL Market-37Countries)
DTV (MPEG2/4, DVB-T2): 8 countries
UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine,
Kazakhstan, Russia
DTV (MPEG2/4, DVB-C): 37 countries
Germany, Netherland, Switzerland, Hungary, Austria,
Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia,
Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania,
Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden,
Denmark, Finland, Norway, Ukraine, Kazakhstan
DTV (MPEG2/4,DVB-S): 30 countries
Germany, Netherland, Switzerland, Hungary, Austria,
Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia,
Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania,
Albania, Bosnia, Serbia, Slovakia, Beralus
Supported satellite : 22 satellites
HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,
ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4,
EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A,
HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/
KR, ASTRA 3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3,
EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURKSAT 2A/3A, INTERSAT10
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-6-
LGE Internal Use Only
No.
2
3
4
Item
Broadcasting system
Program coverage
Receiving system
Specification
1) PAL-BG
2) PAL-DK
3) PAL-I/I’
4) SECAM-L/L', DK , BG, I
5) DVB-T
6) DVB-C
7) DVB-T2
8) DVB-S/S2
1 ) Digital TV
- VHF, UHF
- C-Band,Ku-Band
2) Analogue TV
- VHF : E2 to E12
- UHF : E21 to E69
- CATV : S1 to S20
- HYPER : S21 to S47
Remarks
Model : *L*V*-Z* (T2 only Model)
DVB-S: Satellite
► DVB-T
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-T2 (Model : *L*V*-Z* (T2 only Model))
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
Analog : Upper Heterodyne
Digital : COFDM, QAM
► DVB-C
- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s
- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM
5
Scart (1EA)
PAL, SECAM
6
Video Input RCA(1EA)
PAL, SECAM, NTSC
7
Head phone out
8
Component Input (1EA)
9
HDMI Input (3EA)
10
Audio Input (3EA)
11
12
13
SDPIF out (1EA)
USB (1EA)
Ethernet Connect(1EA)
Antenna, AV1, AV2, Component, HDMI1,
HDMI2, HDMI3, USB1, USB2, USB3
Y/Cb/Cr
Y/Pb/Pr
HDMI1-DTV
HDMI2-DTV
HDMI3-DTV
DVI Audio
Component/AV2
AV1
SPDIF out
EMF, DivX HD, For SVC (download)
Ethernet Connect
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-7-
► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
Scart 1 Jack is Full scart and support ATV/DTV-OUT
(not support DTV Auto AV)
4 System : PAL, SECAM, NTSC, PAL60
Common port
Hybrid Type
HDMI1: PC support(HDMI version 1.3)
Support HDCP
L/R Input.
JPEG, MP3, DivX HD
LGE Internal Use Only
5. Component Video Input (Y, Pb, Pr)
No.
Resolution
H-freq(kHz)
V-freq(Hz)
Pixel clock
1.
720×480
15.73
60.00
SDTV, DVD 480i
2.
720×480
15.63
59.94
SDTV, DVD 480i
3.
720×480
31.47
59.94
480p
4.
720×480
31.50
60.00
480p
5.
720×576
15.625
50.00
SDTV 576i
6.
720×576
31.25
50.00
SDTV 576p
7.
1280×720
45.00
50.00
HDTV 720p
8.
1280×720
44.96
59.94
HDTV 720p
9.
1280×720
45.00
60.00
HDTV 720p
10.
1920×1080
31.25
50.00
HDTV 1080i
11.
1920×1080
33.75
60.00
HDTV 1080i
12.
1920×1080
33.72
59.94
HDTV 1080i
13.
1920×1080
56.250
50
HDTV 1080p
14.
1920×1080
67.5
60
HDTV 1080p
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-8-
LGE Internal Use Only
6. HDMI Input
6.1. DTV mode
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
1.
640*480
2.
720*480
31.469 / 31.5
59.94/60
SDTV 480P
31.469 / 31.5
59.94 / 60
SDTV 480P
3.
4.
720*576
31.25
50
SDTV 576P
720*576
15.625
50
SDTV 576I
5.
1280*720
6.
1280*720
37.500
50
HDTV 720P
44.96 / 45
59.94 / 60
HDTV 720P
7.
1920*1080
8.
1920*1080
33.72 / 33.75
59.94 / 60
HDTV 1080I
28.125
50.00
HDTV 1080I
26.97 / 27
23.97 / 24
HDTV 1080P
25
HDTV 1080P
29.976 / 30.00
HDTV 1080P
9.
1920*1080
10.
1920*1080
11.
1920*1080
12.
1920*1080
56.250
50
HDTV 1080P
13.
1920*1080
67.43 / 67.5
59.94 / 60
HDTV 1080P
33.716 / 33.75
6.2. PC mode
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
1
640 x 350 @70Hz
31.468
70.09
EGA
2
720 x 400 @70Hz
31.469
70.08
DOS
3
640 x 480 @60Hz
31.469
59.94
VESA(VGA)
4
800 x 600 @60Hz
37.879
60.31
VESA(SVGA)
5
1024 x 768 @60Hz
48.363
60.00
VESA(XGA)
6
1152 x 864 @60Hz
54.348
60.053
VESA
7
1280 x 1024 @60Hz
63.981
60.020
VESA(SXGA)
8
1360 x 768 @60Hz
47.712
60.015
VESA(WXGA)
67.5
60.00
WUXGA(Reduced Blanking)
25
HDTV 1080P
9
1920 x 1080 @60Hz
10.
1920*1080
11.
1920*1080
33.716 / 33.75
29.976 / 30.00
HDTV 1080P
12.
1920*1080
56.250
50
HDTV 1080P
13.
1920*1080
67.43 / 67.5
59.94 / 60
HDTV 1080P
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
-9-
LGE Internal Use Only
7. 3D Mode
7.1. HDMI 1.4b (3D supported mode automatically)
No.
Resolution
1
2
640*480
3
4
5
720*480
6
7
8
720*576
9
10
11
720*576
12
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
VIC
3D input proposed mode
Proposed
31.469 / 31.5
59.94/ 60
25.125
1
Top-and-Bottom
Side-by-side(half)
Secondary(SDTV 480P)
Secondary(SDTV 480P)
62.938/63
59.94/ 60
50.35/50.4
1
Frame packing
Line alternative
Secondary(SDTV 480P)
(SDTV 480P)
31.469 / 31.5
59.94/ 60
50.35/50.4
1
Side-by-side(Full)
(SDTV 480P)
Secondary(SDTV 480P)
Secondary(SDTV 480P)
31.469 / 31.5
59.94 / 60
27.00/27.03
2,3
Top-and-Bottom
Side-by-side(half)
62.938/63
59.94 / 60
54/54.06
2,3
Frame packing
Line alternative
Secondary(SDTV 480P)
(SDTV 480P)
31.469 / 31.5
59.94 / 60
54/54.06
2,3
Side-by-side(Full)
(SDTV 480P)
Secondary(SDTV 576P)
Secondary(SDTV 576P)
31.25
50
27
17,18
Top-and-Bottom
Side-by-side(half)
62.5
50
54
17,18
Frame packing
Line alternative
Secondary(SDTV 576P)
(SDTV 576P)
31.25
50
54
17,18
Side-by-side(Full)
(SDTV 576P)
Secondary(SDTV 576I)
Secondary(SDTV 576I)
15.625
50
27
21
Top-and-Bottom
Side-by-side(half)
31.25
50
54
21
Frame packing
Field alternative
Secondary(SDTV 576I)
(SDTV 576I)
15.625
50
54
21
Side-by-side(Full)
(SDTV 576I)
Primary(HDTV 720P)
Primary(HDTV 720P)
Primary(HDTV 720P)
(HDTV 720P)
13
37.500
50
74.25
19
Top-and-Bottom
Side-by-side(half)
14
75
50
148.5
19
Frame packing
Line alternative
37.500
50
148.5
19
Side-by-side(Full)
(HDTV 720P)
Primary(HDTV 720P)
Primary(HDTV 720P)
Primary(HDTV 720P)
(HDTV 720P)
15
1280*720
16
44.96 / 45
59.94 / 60
74.18/74.25
4
Top-and-Bottom
Side-by-side(half)
17
89.91/90
59.94 / 60
148.35/148.5
4
Frame packing
Line alternative
18
44.96 / 45
59.94 / 60
148.35/148.5
4
Side-by-side(Full)
(HDTV 720P)
19
33.72 / 33.75
59.94 / 60
74.18/74.25
5
Top-and-Bottom
Side-by-side(half)
Secondary(HDTV 1080I)
Primary(HDTV 1080I)
20
67.432 / 67.50
59.94 / 60
148.35/148.5
5
Frame packing
Field alternative
Primary(HDTV 1080I)
(HDTV 1080I)
33.72 / 33.75
59.94 / 60
148.35/148.5
5
Side-by-side(Full)
(HDTV 1080I)
Secondary(HDTV 1080I)
Primary(HDTV 1080I)
21
1920*1080
28.125
50.00
74.25
20
Top-and-Bottom
Side-by-side(half)
23
56.25
50.00
148.5
20
Frame packing
Field alternative
Primary(HDTV 1080I)
(HDTV 1080I)
24
28.125
50.00
148.5
20
Side-by-side(Full)
(HDTV 1080I)
25
26.97 / 27
23.97 / 24
74.18/74.25
32
Top-and-Bottom
Side-by-side(half)
Primary(HDTV 1080P)
Primary(HDTV 1080P)
26
43.94/54
23.97 / 24
148.35/148.5
32
Frame packing
Line alternative
Primary(HDTV 1080P)
(HDTV 1080P)
27
26.97 / 27
23.97 / 24
148.35/148.5
32
Side-by-side(Full)
(HDTV 1080P)
Secondary(HDTV 1080P)
Secondary(HDTV 1080P)
22
28
28.125
25
74.25
33
Top-and-Bottom
Side-by-side(half)
29
56.24
25
148.5
33
Frame packing
Line alternative
Secondary(HDTV 1080P)
(HDTV 1080P)
28.12
25
148.5
33
Side-by-side(Full)
(HDTV 1080P)
Primary(HDTV 1080P)
Secondary(HDTV 1080P)
Primary(HDTV 1080P)
(HDTV 1080P)
30
1920*1080
31
33.716 / 33.75
29.976 / 30.00
74.18/74.25
34
Top-and-Bottom
Side-by-side(half)
32
67.432 / 67.5
29.976 / 30.00
148.35/148.5
34
Frame packing
Line alternative
33
33.716 / 33.75
29.976 / 30.00
148.35/148.5
34
Side-by-side(Full)
(HDTV 1080P)
Primary(HDTV 1080P)
Secondary(HDTV 1080P)
Primary(HDTV 1080P)
Secondary(HDTV 1080P)
34
56.250
50
148.5
31
Top-and-Bottom
Side-by-side(half)
35
67.43 / 67.5
59.94 / 60
148.35/148.50
16
Top-and-Bottom
Side-by-side(half)
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 10 -
LGE Internal Use Only
7.2. HDMI Input(1.3)
No.
Resolution
H-freq(kHz) V-freq.(kHz)
Pixel clock(MHz)
Proposed
1
1280*720
45.00
60.00
74.25
HDTV 720P
2
1280*720
37.500
50
74.25
HDTV 720P
3
1920*1080
33.75
60.00
74.25
HDTV 1080I
4
1920*1080
28.125
50.00
74.25
HDTV 1080I
5
1920*1080
27.00
24.00
74.25
HDTV 1080P
6
1920*1080
28.12
25
74.25
HDTV 1080P
7
1920*1080
33.75
30.00
74.25
HDTV 1080P
8
1920*1080
67.50
60.00
148.5
HDTV 1080P
9
1920*1080
56.25
50
148.5
HDTV 1080P
3D input proposed mode
2D to 3D, Side by Side(half),
Top & Bottom, Single Frame Sequential
2D to 3D, Side by Side(half),
Top & Bottom
2D to 3D, Side by Side(Half),
Top & Bottom, Checker Board
2D to 3D, Side by Side(half),
Top & Bottom, Checkerboard,
Single Frame Sequential,
Row Interleaving, Column Interleaving
7.3. RF Input(3D supported mode manually)
No.
Resolution
Proposed
3D input proposed mode
1
HD
1080I
720P
2D to 3D
Side by Side(Half)
Top & Bottom
2
SD
576P
576I
2D to 3D
7.4. RF Input (3D supported mode automatically)
No.
Signal
1
Frame Compatible
3D input proposed mode
Side by Side(Half),
Top & Bottom
7.5. USB Input (3D supported mode manually)
No.
1
Resolution
1920*1080
Others
H-freq(kHz)
33.75
-
V-freq.(Hz)
30
-
Pixel clock(MHz)
Proposed
3D input proposed mode
74.25
HDTV 1080P
2D to 3D, Side by Side(Half)*,
Top & Bottom*, Checkerboard*,
Row Interleaving, Column Interleaving
(Photo : side by Side(half), Top & Bottom)
-
640*350
720*400
640*480
800*600
1152*864
1280*1024
2D to 3D
(“*” 3D supported mode manually & automatically)
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 11 -
LGE Internal Use Only
7.6. HDMI-PC Input (3D supported mode manually)
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock(MHz)
3D input proposed mode
Proposed
1
1024*768
48.36
60
65
2D to 3D, Side by Side(half)
Top & Bottom
2
1360*768
47.71
60
85.5
2D to 3D, Side by Side(half)
Top & Bottom
HDTV 768P
148.50
2D to 3D, Side by Side(half)
Top & Bottom, Checker Board,
Single Frame Sequential,
Row Interleaving,
Column Interleaving
HDTV 1080P
2D to 3D
640*350
720*400
640*480
800*600
1152*864
3
4
1920*1080
67.500
Others
60
-
-
-
HDTV 768P
7.7. DLNA Input (3D supported mode manually)
No.
1
Resolution
1920*1080
H-freq(kHz)
33.75
V-freq.(Hz)
30
Pixel clock(MHz)
Proposed
3D input proposed mode
2D to 3D, Side by Side(Half)*,Top &
Bottom*,Checker Board*, Row Interleaving, Column Interleaving(Photo : Side by
Side(Half), Top&Bottom)
74.25
(“*” 3D supported mode manually & automatically)
7.8. Component Input(3D) (3D supported mode manually)
No.
Resolution
H-freq(kHz)
V-freq.(Hz)
Pixel clock
Proposed
1
1280*720
45.00
60.00
74.25
HDTV 720P
2
1280*720
37.500
50
74.25
HDTV 720P
3
1920*1080
33.75
60.00
74.25
HDTV 1080I
4
1920*1080
28.125
50.00
74.25
HDTV 1080I
5
1920*1080
27.00
24.00
74.25
HDTV 1080P
6
1920*1080
28.12
25
74.25
HDTV 1080P
7
1920*1080
33.75
30.00
74.25
HDTV 1080P
8
1920*1080
67.50
60.00
148.5
HDTV 1080P
9
1920*1080
56.250
50
148.5
HDTV 1080P
3D input proposed mode
2D to 3D, Side by Side(Half), Top & Bottom
7.9. 3D Input mode
No.
Side by Side
Top & Bottom
ii.
iii.
Checker board
Single Frame
Sequential
Frame
Packing
2D to 3D
1
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
iv.
- 12 -
v.
vi.
LGE Internal Use Only
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LED TV with
LD33B chassis.
3.2. LAN Inspection
3.2.1. Equipment & Condition
▪ Each other connection to LAN Port of IP Hub and Jig
2. Designation
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep AC 100-240
V~, 50/60 Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15.
3.2.2. LAN inspection solution
▪ LAN Port connection with PCB
▪ Setting automatic IP
In case of keeping module is in the circumstance of 0 °C, it
should be placed in the circumstance of above 15 °C for 2
hours.
In case of keeping module is in the circumstance of below
-20 °C, it should be placed in the circumstance of above 15
°C for 3 hours.
▪ If you want manual connection, enter Network connection at
MENU Mode of TV. Press Start connection key, then
Network will be connected.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (Especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
3. Automatic Adjustment
3.1. M
AC address D/L, CI+ key D/L, Widevine
key D/L, ESN D/L, HDCP14/20 D/L
Connect: USB port
Communication Prot connection
▪ Com 1,2,3,4 and 115200(Baudrate)
Mode check: Online Only
▪ Check the test process: DETECT -> MAC -> CI -> Widevine
-> ESN -> HDCP14 -> HDCP20
▪ Play: Press Enter key
▪ Result: Ready, Test, OK or NG
▪ Printer Out (MAC Address Label)
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 13 -
▪ Setting state confirmation
- If automatic setting is finished, you confirm IP and MAC
Address at ‘in start’ menu mode.
LGE Internal Use Only
3.2.3. WIDEVINE key Inspection
- Confirm key input data at the "IN START" MENU Mode.
3.4. Model name & Serial number Download
3.4.1. Model name & Serial number D/L
Press "P-ONLY" key of service remote control.
(Baud rate : 115200 bps)
▪ Connect RS-232C Signal to USB Cable to USB.
▪ Write Serial number by use USB port.
▪ Must check the serial number at Instart menu.
▪
3.4.2. Method & notice
(1) Serial number D/L is using of scan equipment.
(2) Setting of scan equipment operated by Manufacturing
Technology Group.
(3) Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0.
* Manual Download (Model Name and Serial Number)
If the TV set is downloaded by OTA or service man, sometimes
model name or serial number is initialized.(Not always)
It is impossible to download by bar code scan, so It need
Manual download.
1) Press the "Instart" key of Adjustment remote control.
2) Go to the menu "7.Model Number D/L" like below photo.
3) Input the Factory model name(ex 42LA690V-ZA) or Serial
number like photo.
3.3. LAN PORT INSPECTION(PING TEST)
Connect SET → LAN port == PC → LAN Port
SET
PC
3.3.1. Equipment setting
(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2
3.3.2. LAN PORT inspection(PING TEST)
(1) Play the LAN Port Test Program.
(2) Connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) Remove LAN cable.
4) Check the model name Instart menu. → Factory name
displayed. (ex 42LA690V-ZA)
5) C heck the Diagnostics.(DTV country only) → Buyer
model displayed. (ex 42LA690V-ZA)
3.5. CI+ Key checking method
- Check the Section 3.1
Check whether the key was downloaded or not at ‘In Start’
menu. (Refer to below).
=> Check the Download to CI+ Key value in LGset.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 14 -
LGE Internal Use Only
4. Manual Adjustment
3.5.1. Check the method of CI+ Key value
(1) Check the method on Instart menu
(2) Check the method of RS232C Command
1) Into the main ass’y mode(RS232: aa 00 00)
CMD 1
CMD 2
Data 0
A
A
0
* ADC adjustment is not needed because of OTP(Auto ADC
adjustment)
0
2) Check the key download for transmitted command
(RS232: ci 00 10)
CMD 1
CMD 2
C
I
4.1. EDID DATA
4.1.1. 3D EDID
Data 0
1
0
3) Result value
- Normally status for download : OKx
- Abnormally status for download : NGx
3.5.2. Check the method of CI+ key value(RS232)
1) Into the main ass’y mode(RS232: aa 00 00)
CMD 1
CMD 2
Data 0
A
A
0
▪ Reference
- HDMI1 ~ HDMI4 / RGB
- In the data of EDID, bellows may be different by S/W or
Input mode.
ⓐ Product ID
0
2) Check the mothed of CI+ key by command
(RS232: ci 00 20)
CMD 1
CMD 2
C
I
Data 0
2
HEX
0001
0001
0
3) Result value
i 01 OK 1d1852d21c1ed5dcx
3.6. WIFI MAC ADDRESS CHECK
(1) Using RS232 Command
Transmission
V-freq.(Hz)
[A][I][][Set ID][][20][Cr]
[O][K][X] or [NG]
DDC Function
Analog
Digital
ⓑ Serial No: Controlled on production line.
ⓒ Month, Year: Controlled on production line:
ex) Monthly : ‘01’ → ‘01’
Year : ‘2013’ → ‘17’
ⓓ Model Name(Hex): LGTV
CI+ Key Value
H-freq(kHz)
EDID Table
0100
0100
Chassis
MODEL NAME(HEX)
LD33B
00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓔ Checksum(LG TV): Changeable by total EDID data.
ⓔ1
(2) Check the menu on in-start
HDMI1
HDMI2
HDMI3
E8
E8
E8
ⓔ2
10bit
/none XvYcc
85
75
65
ⓔ2
8bit
/none XvYcc
CC
BC
AC
ⓔ3
X
X
X
ⓕ Vendor Specific(HDMI)
1) Deep color (module 10bit)
INPUT
MODEL NAME(HEX)
HDMI1
78 03 0C 00 10 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI2
78 03 0C 00 20 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI3
78 03 0C 00 30 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
2) None deep color (module 8bit)
INPUT
MODEL NAME(HEX)
HDMI1
78 03 0C 00 10 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI2
78 03 0C 00 20 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI3
78 03 0C 00 30 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
ⓖ Colorimetry Data Block(HDMI)
1) The Model not supporting XvYcc
INPUT
HDMI1
HDMI2
HDMI3
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 15 -
MODEL NAME(HEX)
E3 05 00 00
E3 05 00 00
E3 05 00 00
LGE Internal Use Only
4.1.2. 2D EDID
4.2.3. Equipment connection MAP
Co lo r Analyzer
RS -232C
Probe
Co m p ut er
RS -232C
RS -232C
Pat t ern Generat o r
Signal Source
* If TV internal pattern is used, not needed
▪ Reference
- HDMI1 ~ HDMI4 / RGB
- In the data of EDID, bellows may be different by S/W or
Input mode.
ⓐ Product ID
HEX
0001
0001
EDID Table
0100
0100
4.2.4. Adj. Command (Protocol)
DDC Function
Analog
Digital
ⓑ Serial No: Controlled on production line.
ⓒ Month, Year: Controlled on production line:
ex) Monthly : ‘01’ → ‘01’
Year : ‘2012’ → ‘16’
ⓓ Model Name(Hex): LGTV
Chassis
LD33B
HDMI1
HDMI2
HDMI3
ⓔ3
X
X
X
A
CMD
A
00
A
VAL
A
CS STOP
Explantion
wb
00
00
Begin White Balance adjustment
wb
00
10
Gain adjustment(internal white pattern)
wb
00
1f
Gain adjustment completed
wb
00
20
Offset adjustment(internal white pattern)
wb
00
2f
Offset adjustment completed
wb
00
ff
End White Balance adjustment
(internal pattern disappears )
wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f → Gain adj. completed
*(wb 00 20(Start), wb 00 2f(end)) → Off-set adj.
wb 00 ff → End white balance auto-adj.
MODEL NAME(HEX)
67 03 0C 00 10 00 80 2D
67 03 0C 00 20 00 80 2D
67 03 0C 00 30 00 80 2D
4.2. White Balance Adjustment
4.2.1. Overview
▪ W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panel's W/B deviation
(2) How-it-works : When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one
of R/G/B is fixed at 192, and the other two is lowered to
find the desired value.
(3) Adjustment condition : normal temperature
1) Surrounding Temperature : 25 °C ± 5 °C
2) Surrounding Humidity : 20 % ~ 80 %
4.2.2. Equipment
(1) Color Analyzer: CA-210 (LED Module : CH 14)
(2) Adjustment Computer(During auto adj., RS-232C protocol
is needed)
(3) Adjustment Remote control
(4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model: 217, Pattern: 78)
→ Only when internal pattern is not available
▪ Color Analyzer Matrix should be calibrated using CS-1000.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
A LEN A 03
Ex)
ⓕ Vendor Specific(HDMI)
INPUT
HDMI1
HDMI2
HDMI3
50
RS-232C COMMAND
[CMD
ID
DATA]
ⓔ Checksum(LG TV): Changeable by total EDID data.
ⓔ2
15
05
F5
A
- LEN: Number of Data Byte to be sent
- CMD: Command
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
▪ RS-232C Command used during auto-adjustment.
MODEL NAME(HEX)
00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓔ1
43
43
43
<Command Format>
START 6E
- 16 -
▪ Adj. Map
Applied Model : LD33B Chassis ALL MODELS
Adj. item
Cool
Medium
Warm
R Gain
G Gain
B Gain
R Cut
G Cut
B Cut
R Gain
G Gain
B Gain
R Cut
G Cut
B Cut
R Gain
G Gain
B Gain
R Cut
Command
(lower caseASCII)
CMD1
CMD2
j
g
j
h
j
i
Data Range
(Hex.)
MIN
MAX
00
C0
00
C0
00
C0
j
j
j
a
b
c
00
00
00
C0
C0
C0
j
j
j
d
e
f
00
00
00
C0
C0
C0
Default
(Decimal)
G Cut
LGE Internal Use Only
4.2.5. Adj. method
(1) Auto adj. method
1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the
Display.
3) Connect Cable.(RS-232C to USB)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sign), check adj. status pre
mode. (Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
▪ W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.
▪ Standard color coordinate and temperature using CA-210(CH 14)
▪ Adjustment condition and cautionary items
1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.
2) Probe location
: Color Analyzer(CA-210) probe should be within 10 cm
and perpendicular of the module surface (80° ~ 100°)
3) Aging time
- After Aging Start, Keep the Power ON status during 5
Minutes.
- In case of LCD, Back-light on should be checked
using no signal or Full-white pattern.
4.2.6. Reference (White balance Adj. coordinate and
color temperature)
▪ Luminance : 204 Gray
▪ Standard color coordinate and temperature using CS-1000
(over 26 inch)
Coordinate
Mode
Temp
∆uv
x
y
Cool
0.269
0.273
13000 K
0.0000
0.285
0.293
9300 K
0.0000
Warm
0.313
0.329
6500 K
0.0000
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
x
y
Temp
∆uv
Cool
0.269 ± 0.002
0.273 ± 0.002
13000 K 0.0000
Medium
0.285 ± 0.002
0.293 ± 0.002
9300 K
0.0000
Warm
0.313 ± 0.002
0.329 ± 0.002
6500K
0.0000
4.2.7. ALELF & EDGE LED White balance table
(2) Manual adjustment. method
1) Set TV in Adj. mode using POWER ON.
2) Zero Calibrate the probe of Color Analyzer, then place it
on the center of LCD module within 10 cm of the
surface.
3) Press ADJ key → EZ adjust using adj. R/C → 7. WhiteBalance then press the cursor to the right(key ►).
(When right key(►) is pressed 204 Gray internal pattern
will be displayed)
4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
5) Adjustment is performed in COOL, MEDIUM, WARM 3
modes of color temperature.
▪ If internal pattern is not available, use RF input. In EZ Adj.
menu 7.White Balance, you can select one of 2 Testpattern: ON, OFF. Default is inner(ON). By selecting OFF,
you can adjust using RF signal in 204 Gray pattern.
Medium
Coordinate
Mode
- 17 -
- EDGE LED module change color coordinate because of
aging time.
- Apply under the color coordinate table, for compensated
aging time.
* Normal Line
[LN5xxx, LA6xxx, LA7xxx, LA8xxx]
NC4.0
Aging
time
(Min)
1
2
3
4
5
6
7
8
9
0-2
3-5
6-9
10-19
20-35
36-49
50-79
80-119
Over 120
Cool
X
y
271
270
283
287
282
285
281
284
279
281
277
277
275
274
273
272
272
271
271
270
Medium
x
y
286
289
298
306
297
304
296
303
294
300
292
296
290
293
288
291
287
290
286
289
Warm
x
y
313
329
322
342
321
340
320
339
318
336
316
332
314
329
312
327
311
326
310
325
Medium
x
y
286
289
297
304
293
299
290
294
287
291
284
288
283
286
282
285
281
283
280
282
Warm
x
y
313
329
321
340
317
335
314
330
311
327
308
324
307
322
306
321
305
319
304
318
*Aging Chamber
[LN5xxx, LA6xxx, LA7xxx, LA8xxx]
NC4.0
Aging
time
(Min)
1
2
3
4
5
6
7
8
9
0-5
6-10
11-20
21-30
31-40
41-50
51-80
81-119
Over 120
Cool
X
y
271
270
282
285
278
280
275
275
272
272
269
269
268
267
267
266
266
264
265
263
LGE Internal Use Only
4.3. Local Dimming Function Check
(2) When 3D OSD appear automatically, then select OK key.
Step 1) Turn on TV.
Step 2) At the Local Dimming mode, module Edge Backlight
moving right to left Back light of IOP module moving.
Step 3) Confirm the Local Dimming mode.
Step 4) Press "exit" key.
(3) Don't wear a 3D Glasses, check the picture like below.
4.6. Wi-Fi Test
4.4. Magic Motion Remote control test
- R esults are automatically marked in Instart OSD after
through the AP/Magic Remocon Equipment on the line
Step 1) Turn on TV
Step 2) Select Network Connection option in Network Menu.
Step 3) Select Start Connection button in Network Connection.
Step 4) If the system finds any AP like blow PIC, it is working
well.
4.5. 3D function test
(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])
* HDMI mode NO. 872 , pattern No.83
(1) Please input 3D test pattern like below.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 18 -
LGE Internal Use Only
4.7. LNB voltage and 22KHz tone check
(only for DVB-S/S2 model)
▪ Test method
(1) Set TV in Adj. mode using POWER ON.
(2) Connect cable between satellite ANT and test JIG.
(3) Press Yellow key(ETC+SWAP) in Adj Remote control to
make LNB on.
(4) Check LED light ‘ON’ at 18 V menu.
(5) Check LED light ‘ON’ at 22 KHz tone menu.
(6) Press Blue key(ETC+PIP INPUT) in Adj Remote control
to make LNB off.
(7) Check LED light ‘OFF’ at 18 V menu.
(8) Check LED light ‘OFF’ at 22 KHz tone menu.
7. GND and Internal Pressure check
7.1. Method
(1) GND & Internal Pressure auto-check preparation
- Check that Power cord is fully inserted to the SET.
(If loose, re-insert)
(2) Perform GND & Internal Pressure auto-check
- Unit fully inserted Power cord, Antenna cable and A/V
arrive to the auto-check process.
- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX.)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow the
pallet to move on to next process.
▪ Test result
(1) After press LNB On key, ‘18 V LED’ and ‘22 KHz tone
LED’ should be ON.
(2) After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone
LED’ should be OFF.
4.8. Option selection per country
7.2. Checkpoint
4.8.1. Overview
▪ TEST voltage
- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA
▪ TEST time: 1 second
▪ TEST POINT
- GND TEST = POWER CORD GND & SIGNAL CABLE
METAL GND
- Internal Pressure TEST = POWER CORD GND & LIVE &
NEUTRAL
▪ LEAKAGE CURRENT: At 0.5 mArms
- Option selection is only done for models in Non-EU
4.8.2. Method
(1) Press ADJ key on the Adj. R/C, then select Country Group
Meun
(2) Depending on destination, select Country Group Code 04
or Country Group EU then on the lower Country option,
select US, CA, MX. Selection is done using +, - or ►◄
key.
5. Tool Option selection
▪ Method : Press "ADJ" key on the Adjustment remote control,
then select Tool option.
8. Audio
6. Ship-out mode check(In-stop)
▪ After final inspection, press "IN-STOP" key of the Adjustment
remote control and check that the unit goes to Stand-by
mode.
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 19 -
Measurement condition:
(1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
(2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms
(3) RGB PC: 1 KHz sine wave signal 0.7 Vrms
No.
Item
Min
Typ
Max
Unit
9
10
12
W
1.
Audio practical
max Output, L/R
(Distortion=10%
max Output)
8.10
10.8
Vrms
2.
Speaker (8Ω
Impedance)
10
12
W
9
Remark
EQ Off
AVL Off
Clear Voice Off
LGE Internal Use Only
9. USB S/W Download(Service only)
(1) Put the USB Stick to the USB socket
(2) Automatically detecting update file in USB Stick
- I f your downloaded program version in USB Stick is
Lower, it didn’t work.
B ut your downloaded version is Higher, USB data is
automatically detecting (Download Version High & Power
only mode, Set is automatically Download)
(3) Show the message “Do not unplug!”
(4) Updating is starting.
(5) Updating Completed, The TV will restart automatically
(6) If your TV is turned on, check your updated version and
Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV have,
TV can lost all channel data. In this case, you have to
channel recover. if all channel data is cleared, you didn’t
have a DTV/ATV test on production line.
* After downloading, have to adjust Tool Option again.
(1) Push "IN-START" key in service remote control.
(2) Select "Tool Option 1" and push "OK" key.
(3) Punch in the number. (Each model has their number)
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 20 -
LGE Internal Use Only
R
E
A
DVB-S
R
(H)
Air/
Cable
T/C/S2 Tuner
LNB
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
- 21 R
E
A
R
S
I
D
E
S
I
D
E
SPDIF OUT
ETHERNET
OPTIC
LAN
CVBS/YPbPr
HDMI
MUX
USB
CVBS/RGB
AMP
OCP
MHL
IC
OCP
OCP
P_TS
LGE2122
T/C Demod
Analog Demod
P_TS
X_TAL
SCART
AV/COMP
H/P
(MHL)
HDMI3
HDMI2
HDMI1
USB2
USB3
USB1
(HDD)
P_TS
IF (+/-)
P_TS
CI Slot
A
LEVEL
SHIFTER
USB_WIFI
X_TAL
Sub Micom
IR
LOGO LIGHT
KEY
WIFI
BLUTOOTH
Audio AMP
PM
IC
UART
50P
50P
eMMC
SYSTEM EEPROM
DDR3
LOCAL DIMMING
B
SPI
EPI
DDR3
SUB
ASSY
BLOCK DIAGRAM
LGE Internal Use Only
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
- 22 -
* Set + Stand
* Stand Base + Body
AG1
A10
122
200T
200
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Only LGD Module
A2
510
LV1
123
120
501
570
502
530
500
540
521
900
400
910
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by
in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
LGE Internal Use Only
EAX64797001* : LD33B
EAX64872101* : LA33B
X-TAL
IC100-*1
M24256-BRMN6TP
NVRAM
+3.3V_NORMAL
E0
E1
E2
R101
4.7K
R102
4.7K
OPT
R100
IC100
AT24C256C-SSHL-T
VSS
8
2
7
3
6
4
5
VCC
A0
WC
A1
SCL
A2
SDA
VSS
NVRAM_ST
A0
4.7K
OPT
+3.3V_NORMAL
1
IC100-*2
R1EX24256BSAS0A
A1
A2
1
8
2
7
3
6
1
8
2
7
3
6
4
5
X-TAL_1
1
C114
GND_1
1.0pF
2
50V DVB_1pF
MT5398_XTAL_IN
Close to eMMC Flash
(IC8100)
GND_2
4
X-TAL_2
3
EMMC_CLK
WP
R168
10K
MT5398_XTAL_OUT
C115
1.0pF
50V
C114-*1
2.7pF
50V
ATSC_2.7pF
VCC
SCL
X100
27MHz
C115-*1
2.7pF
50V
ATSC_2.7pF
DVB_1pF
SDA
NVRAM_RENESAS
VCC
Write Protection
WP
- Low : Normal Operation
- High : Write Protection
SCL
R135
33
SDA
R134
33
IC105
LGE2122[A2_M13]
VDD3V3
I2C_SCL5
+3.3V_NORMAL
I2C_SDA5
NVRAM_ATMEL
AK10
L/DIM0_MOSI
AK11
L/DIM0_SCLK
AL9
AJ11
AJ12
L/DIM0_VS
HDCP EEPROM
OSDA0
+3.3V_NORMAL
AH10
7
3
6
VSS 4
5
AVDD_33SB
WC
SCL
SDA
R125
4.7K
OPT
R126
22
OPT
R127
22
STRAPPING
I2C_SCL1
LED_PWM0
LED_PWM1
OPCTRL3
1
0
0
0
ICE mode + 27M + ROM to Nand boot
1
0
0
1
U1RX
AM29
AL29
C111
0.1uF
OSDA0
POWE
POOE
POCE1
OSDA1
POCE0
OSCL1
PDD7
PDD6
XTALI
PDD5
XTALO
PDD4
Wake On Lan
PDD3
AVDD33_XTAL_STB
PDD2
AVSS33_XTAL_STB
PDD1
PDD0
I2C_SDA1
OPT
+3.3V_NORMAL
R155
1K
OPT
R162
1K
R157
1K
ICE mode + 27M + ROM to 60bit ECC Nand boot
1
0
1
0
ICE mode + 27M + ROM to eMMC boot from
EMMC pins (share pins w/s NAND)
1
0
1
1
ICE mode + 27M + ROM to eMMC
Boot from SDIO pins
R163
1K
1
1
0
PARB
AVDD_33SB
PACLE
AN17
C110
0.1uF
AL17
PAALE
AVDD33_VGA_STB
AVSS33_AVSS33_VGA_STB
AL26
C109
0.1uF
AC21
H21
OPT
I2C
:
:
:
:
:
:
R133
2.7K
R138
2.7K
R141
2.7K
R142
2.7K
R147
2.7K
R150
2.7K
R151
2.7K
R152
2.7K
NON_TU_Q_KR
R132
2.7K
R161
1K
TU_N_TW/BR
1.2K
R120
33
STB_SDA
R115
33
I2C_SDA1
OPCTRL_11_SCL
R116
33
I2C_SCL2
R117
33
I2C_SDA2
OSCL1
R118
33
OSDA1
R119
33
OSCL2
R110
33
I2C_SCL4
OSDA2
R111
33
I2C_SDA4
R153-*2
SOC -> CI SLOT
B30
A31
CI_ADDR[2]
B31
CI_ADDR[3]
A32
CI_ADDR[4]
C30
CI_ADDR[5]
A33
CI_ADDR[6]
B32
CI_ADDR[7]
C31
CI_ADDR[8]
E30
CI_ADDR[9]
F29
MT5398_MCLKI
MT5398_MIVAL_ERR
CI_ADDR[10]
F27
CI_ADDR[11]
F28
MT5398_MISTRT
CI_ADDR[12]
C32
CI_ADDR[13]
F30
CI_ADDR[14]
F32
SOC -> CI SLOT
I2C_SCL_MICOM
D30
MT5398_TS_OUT[0-7]
I2C_SDA_MICOM
D32
F31
MT5398_TS_OUT[0]
F33
R112
33
I2C_SCL5
MT5398_TS_OUT[1]
E31
OSDA0
R113
33
I2C_SDA5
MT5398_TS_OUT[2]
E32
OPCTRL_1_SCL
R114
33
I2C_SCL6
MT5398_TS_OUT[3]
D31
OPCTRL_0_SDA
R109
33
I2C_SDA6
MT5398_TS_OUT[4]
D33
MT5398_TS_OUT[5]
E29
MT5398_TS_OUT[6]
C33
MT5398_TS_OUT[7]
B33
CI_DATA[0-7]
CI_DATA[0]
A30
CI_DATA[1]
E28
CI_DATA[2]
C29
CI_DATA[3]
J28
CI_DATA[4]
H29
CI_DATA[5]
J26
CI_DATA[6]
G30
CI_DATA[7]
G27
E27
MT5398_TS_IN[0]
D29
MT5398_TS_IN[1]
MTK_EPI
R149
4.7K
DDR_0.78G
R146
4.7K
MTK_DVB_S_TUNER
R145
4.7K
MTK_DVB_T2_TUNER
R140
4.7K
MTK_CP_BOX
R137
4.7K
MTK_DDR_1.25GB
R131
4.7K
MODULE_V13
R130
4.7K
MTK_FHD
R108
4.7K
FRC_120Hz
R106
4.7K
Country_TW
R105
4.7K
Country_AJJA
R123
4.7K
Model Option
CI SLOT -> SOC
D28
MT5398_TS_IN[2]
MT5398_TS_IN[3]
H28
J27
MT5398_TS_IN[4]
HIGH
LOW
MODEL_OPT_0
MODEL_OPT_0
Country_TW
TW
MODEL_OPT_1
FRC
MODEL_OPT_2
Panel
FRC(120Hz) No FRC(60Hz)
MODEL_OPT_2
FHD
HD
MODEL_OPT_3
MODEL_OPT_3 Country_AJJA
AJJA
Non_AJJA
Module
V13
V12
MODEL_OPT_5
DDR
DDR_1.25G
MODEL_OPT_7
MODEL_OPT_6
CP BOX
Enable
MODEL_OPT_8
MODEL_OPT_7
T2 Tuner
Support
MODEL_OPT_4
MODEL_OPT_5
MODEL_OPT_6
MODEL_OPT_4
G29
MT5398_TS_IN[5]
GPIO45(EMMC_RST) is dedicated to reset
EMMC for improving A1’s leakage current
G31
MT5398_TS_IN[6]
MT5398_TS_IN[7]
Non_TW
MODEL_OPT_1
/S2_RESET
G28
/USB_OCD2
B28
/USB_OCD1
K28
/USB_OCD3
E25
D21
EMMC_RST
USB_CTL1
G23
C28
#SIL_RESET
EPI_LOCK6
DDR_1.5G
CTS
RTS
Disable
MODEL_OPT_8
MODEL_OPT_9
DDR
DDR_0.78G
MODEL_OPT_10
EPI
Support
MODEL_OPT_7
Not Support
NON_DDR_0.78G
MODEL_OPT_5
MODEL_OPT_6
NON_EU
R169
10K
Not Support
R170
F24
AB8
AA7
AD6
AC8
AC7
AB6
AC6
CAM_SLIDE_DET
R188
4.7K
D23
C24
C25
WOL/ETH_POWER_ON
R187
4.7K
OPT +3.3V_NORMAL
CAM_SLIDE_DET
A26
EMMC_DATA[1]
B26
EMMC_DATA[0]
C21
EMMC_CLK
R158
R189
10K
OPT
R186
SOC_RESET
C117
0.1uF
16V
C20
FSRC_WR
AL14
STB_SCL
AN16
STB_SCL
AK15
STB_SDA
STB_SDA
R193
AE14
4.7K
POR_BND
AH23
MODEL_OPT_0
M_RFModule_RESET
DDR_1.25G
DDR_1.5G
DDR_0.768G
OPC_EN
/TU_RESET1
High
Low
High
Low
Low
High
MODEL_OPT_4
P30
GPIO0
DEMOD_RST
GPIO1
DEMOD_TSCLK
GPIO2
DEMOD_TSDATA0
GPIO3
DEMOD_TSDATA1
GPIO4
DEMOD_TSDATA2
GPIO5
DEMOD_TSDATA3
GPIO6
DEMOD_TSDATA4
GPIO7
DEMOD_TSDATA5
GPIO8
DEMOD_TSDATA6
GPIO9
DEMOD_TSDATA7
GPIO10
DEMOD_TSSYNC
GPIO11
DEMOD_TSVAL
GPIO12
GPIO13
CI_TSCLK
GPIO15
CI_TSDATA0
GPIO16
CI_TSSYNC
GPIO17
CI_TSVAL
GPIO18
GPIO19
D100
1N4148W
R196
240
Q100 +3.3V_NORMAL
PMV48XP
100V
G
/S2_RESET
AD28
AF22
AK21
AG24
AM18
R27
PVR_TSVAL
GPIO21
PVR_TSSYNC
GPIO22
PVR_TSDATA0
GPIO23
PVR_TSDATA1
GPIO24
SPI_CLK1
GPIO26
SPI_CLK
GPIO27
SPI_DATA
GPIO28
SPI_CLE
GPIO29
FE_DEMOD1_TS_DATA[0]
FE_DEMOD1_TS_DATA[1]
T26
T27
FE_DEMOD1_TS_DATA[2]
P26
FE_DEMOD1_TS_DATA[3]
R28
FE_DEMOD1_TS_DATA[4]
U27
FE_DEMOD1_TS_DATA[5]
U26
FE_DEMOD1_TS_DATA[6]
R29
FE_DEMOD1_TS_SYNC
P27
FE_DEMOD1_TS_VAL
/PCM_REG
N33
/PCM_CE1
MT5398_TS_SYNC CI SLOT -> SOC
/PCM_WE
K26
N30
N31
/PCM_OE
MT5398_TS_VAL CI SLOT -> SOC
CI_A_VS1
M27
L27
MT5398_TS_CLK CI SLOT -> SOC
/PCM_IRQA
M29
M30
L33
L32
K27
/PCM_WAIT
+3.3V_NORMAL
/CI_CD2
/CI_CD1
/PCM_IORD
R174
4.7K
OPT
/PCM_IOWR
AL8
GPIO30
OPWM2
GPIO31
OPWM1
GPIO32
OPWM0
GPIO33
R178
/RST_HUB
R173
1K
D27
GPIO34
SD_D0
GPIO35
SD_D1
SD_D2
GPIO37
SD_D3
GPIO38
SD_CMD
GPIO39
SD_CLK
R177
4.7K
OPT
R179 PWM_DIM2
AM8
AM9
EXTERNAL DEMOD
-> SOC
FE_DEMOD1_TS_DATA[7]
R26
L30
GPIO25
FE_DEMOD1_TS_DATA[0-7]
PCM_RST
FE_DEMOD1_TS_CLK
M31
PVR_TSCLK
GPIO20
GPIO36
N32
L25
CI_INT
GPIO14
22
22
PWM_DIM2
PWM_DIM1
R176
1K
/RST_HUB
C27
D26
PWM2_PULL_DOWN_1K
PWM1_PULL_DOWN_1K
C26
A28
E24
SMARTCARD_CLK/SD_EMMC_DATA[0]
GPIO40
SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]
GPIO41
SMARTCARD_RST/SD_EMMC_DATA[2]
GPIO42
SMARTCARD_DET/SD_EMMC_DATA[3]
GPIO43
SMARTCARD_VCC/SD_EMMC_CMD
GPIO44
SMARTCARD_DATA/SD_EMMC_CLK
SMARTCARD_CLK/SD_EMMC_DATA[0]
SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]
SMARTCARD_RST/SD_EMMC_DATA[2]
SMARTCARD_DET/SD_EMMC_DATA[3]
SMARTCARD_VCC/SD_EMMC_CMD
SMARTCARD_DATA/SD_EMMC_CLK
GPIO45
GPIO46
GPIO47
AF15
GPIO48
LED_PWM1
GPIO49
LED_PWM0
AG15
LED_PWM1
LED_PWM0
GPIO50
GPIO51
5V Tolerance
GPIO52
AL16
GPIO53
OPCTRL11
GPIO54
OPCTRL10
GPIO55
OPCTRL9
OPCTRL8
AJ23
10K
AE28
USB_CTL3
MODEL_OPT_9
Copyright © 2013 LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Support
MODEL_OPT_3
SC_ID_SOC
MODEL_OPT_5
THE
SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE
SYMBOL MARK OF THE SCHEMETIC.
S Tuner
Not Support
MODEL_OPT_10
MTK_NON_EPI
R148
4.7K
NON_DDR_0.78G
R144
4.7K
MTK_NON_DVB_S_TUNER
R143
4.7K
MTK_NON_DVB_T2_TUNER
R139
4.7K
MTK_NON_CP_BOX
R136
4.7K
MTK_DDR_1.5GB
R129
4.7K
MODULE_V12
R128
4.7K
Non_Country_AJJA
R122
4.7K
MTK_HD
R107
4.7K
NON_FRC_60Hz
R104
4.7K
NON_Country_TW
R103
4.7K
OTP_WRITE
MODEL_OPT_9
AVDD_33SB
OTP_WRITE
CI_ADDR[0]
CI_ADDR[1]
OSCL0
+3.3V_NORMAL
EMMC_DATA[2]
IC105
LGE2122[A2_M13]
CI_ADDR[0-14]
I2C_SCL1
OPCTRL_10_SDA
EMMC_DATA[3]
B23
CI_ADDR[0-14]
TU_N_TW/BR
1.2K
STB_SCL
EMMC_DATA[4]
A23
22
AVDD10_ELDO
R152-*2
EMMC_DATA[5]
C23
AF17
C112
4.7uF
10V
R153-*1
R152-*1
TU_Q_KR
TU_Q_KR
1.5K
1.5K
R153
2.7K
A22
ORESET
AVSS33_PLLGP
AVDD10_LDO
AMP, L/DIMMING,HDCP KEY
T-CON,
MICOM
S/Demod,T2/Demod, LNB, MHL(Sil1292)
NVRAM
TUNER_MOPLL(T/C,ATV)
NON_TU_Q_KR
R124
1.2K
B22
EMMC_DATA[6]
AK20
AM17
C107
4.7uF
10V
+3.3V_NORMAL
R121
1.2K
EMMC_DATA[7]
OIRI
OPCTRL7
I2C_1
I2C_2
I2C_3
I2C_4
I2C_5
I2C_6
C22
22
AVDD33_PLL
AVSS33_CPUPLL
OPCTRL3
R160
1K OPT
EMMC_DATA[2-7]
FE_LNA_Ctrl2
A25
OPWRSB
LED_PWM1
R156
1K OPT
FE_LNA_Ctrl1
D25
AL15
LED_PWM0
R154
1K
EMMC_CMD
B25
EMMC_CLK
VDD3V3
0
M_REMOTE_TX
M_REMOTE_RX
D24
AN30
OPCTRL7
ICE mode + 27M + serial boot
JTRST
AN29
MT5398_XTAL_IN
MT5398_XTAL_OUT
R184
4.7K
AG13
10K
R190
NC_3
2
VCC
U1TX
S
NC_2
8
1
R183
4.7K
SOC_RX
D
NC_1
AG11
SOC_TX
AH14
AH13
JTMS
OSCL0
OSCL1
OPT
C100
0.1uF
16V
U0RX
JTDO
AF11
OSDA1
OPT
U0TX
JTDI
AH11
OSCL0
IC101
M24C16-R
AH15
JTCK
R180 4.7K
5
R195
10K
4
R194
10K
GND
ADIN0_SRV
OPCTRL7
ADIN1_SRV
OPCTRL6
ADIN2_SRV
OPCTRL5
ADIN3_SRV
OPCTRL4
ADIN4_SRV
OPCTRL3
ADIN5_SRV
OPCTRL2
ADIN6_SRV
OPCTRL1
ADIN7_SRV
OPCTRL0
AM16
AE17
AG19
AH17
AE19
AH19
AK16
AG17
AJ17
AF19
AJ19
OPCTRL_11_SCL
OPCTRL_10_SDA
COMP1_DET
SC_DET
OPCTRL7
HP_DET
AV1_CVBS_DET
AMP_RESET_SOC
OPCTRL3
RF_SWITCH_CTL
OPCTRL_1_SCL
OPCTRL_0_SDA
MID_MAIN_1
R182
AMP_RESET_SOC
AMP_RESET_N
33
R185
10K
2011.12.13
8
LGE Internal Use Only
PLACE AT JACK SIDE
Close to JACK
Close to Main Chip
C345
10uF
16V
+5V_NORMAL
1608 sizs For EMI
1.0Vpp
COMP1/AV1/DVI_L_IN_SOC
1uF
HDMI_ARC
C346
10uF
16V
R309
100K
PCB_700*
C342
100pF
50V
1608 sizs For EMI
R345
C391
27pF
50V
OPT
C386
27pF
50V
OPT
R381
0
COMP1_Pb_SOC
R354
75
1%
C379
10pF
50V
1608 sizs For EMI
0
R372
C385
27pF
50V
FOR EMI
OPT
ZD306
ADLC 5S 02 015
COMP1_Pr
1%
C384
10pF
50V
COMP1_COM_SOC
ZD304
ADLC 5S 02 015
C343
100pF
50V
R355
75
1/16W
COMP1_Pb
30K
C339
560pF
50V
OPT
R329
470K
OPT
COMP1_Y/AV1_CVBS_SOC
C394
27pF
50V
OPT
1608 sizs For EMI
0
R373
COMP1/AV1/DVI_R_IN_SOC
COMP1/AV1/DVI_R_IN
R374
C388
27pF
50V
OPT
PCB_700*
C311
R303
82
ZD302
ADLC 5S 02 015
C338
560pF
50V
OPT
10V
R302
180
0
COMP1_Y/AV1_CVBS
30K
R328
470K
OPT
ARC
1608 sizs For EMI
R344
COMP1/AV1/DVI_L_IN
R308
1.2K
OPT
COMP1_Pr_SOC
C392
27pF
50V
OPT
R353
75
1%
C378
10pF
50V
IC105
LGE2122[A2_M13]
IC105
LGE2122[A2_M13]
Y1
BE0P
AG30
HDMI_CEC
HDMI_0_RX_0
HDMI_0_RX_0B
AC27
AB27
DDC_SCL_3_JACK
AA26
DDC_SCL_1_SOC
W27
DDC_SCL_MHL
HDMI_0_SCL
HDMI_0_RX_1
HDMI_1_SCL
HDMI_0_RX_1B
HDMI_2_SCL
HDMI_0_RX_2
HDMI_3_SCL
HDMI_0_RX_2B
HDMI_0_SDA
HDMI_0_RX_CB
HDMI_0_RX_C
AC26
AB26
DDC_SDA_3_JACK
Y26
DDC_SDA_1_SOC
DDC_SDA_MHL
W26
5V_HDMI_3_JACK
5V_HDMI_1_SOC
5VBUS
1K
Y27
R306
1K
AA28
R307
1K
V28
HDMI_1_RX_0
HDMI_3_SDA
HDMI_1_RX_0B
HDMI_0_PWR5V
HDMI_1_RX_1B
HDMI_1_RX_1
HDMI_1_PWR5V
HDMI_1_RX_2
HDMI_2_PWR5V
HDMI_1_RX_2B
HDMI_3_PWR5V
AA27
AA29
HDMI_HPD_1_SOC
+1.2V_MTK_AVDD
V29
HDMI_HPD_4_MHL
HDMI_1_RX_C
P33
VDD3V3_HDMI
P32
HDMI_1_HPD
HDMI_2_RX_0
HDMI_2_HPD
HDMI_2_RX_0B
HDMI_2_RX_1
HDMI_2_RX_1B
AVDD12_HDMI_0_RX
HDMI_2_RX_2
AVDD12_HDMI_1_RX
HDMI_2_RX_2B
AVDD12_HDMI_2_RX
HDMI_2_RX_C
AVDD12_HDMI_3_RX
HDMI_2_RX_CB
AH33
HDMI_3_RX_0
HDMI_3_RX_0B
C307
0.1uF
HDMI_3_RX_1
HDMI_3_RX_1B
HDMI_3_RX_2
AE27
T25
W25
AD27
AC33
AC30
AC31
AE30
AE31
W6
MODEL_OPT_10
AVSS33_HDMI_RX_1
HDMI_3_RX_2B
AVSS33_HDMI_RX_2
HDMI_3_RX_C
AVSS33_HDMI_RX_3
HDMI_3_RX_CB
D0+_HDMI3_JACK
MCLK_SOC
D0-_HDMI3_JACK
D1+_HDMI3_JACK
GST_SOC
U6
VCOM_DYN
D2+_HDMI3_JACK
PMIC_RESET
D2-_HDMI3_JACK
2D/3D_CTL
V8
V6
AB7
W9
W33
V9
V7
AA30
AA31
U31
T32
T33
T30
T31
V30
TCON5
BO0N
TCON6
BO1P
TCON7
BO1N
BOCKN
TCON12
BO3P
AN3
AN4
CK+_HDMI1_SOC
AM3
D0-_HDMI4_MHL
D1+_HDMI4_MHL
AF5
D1-_HDMI4_MHL
AE5
D2+_HDMI4_MHL
AC5
D2-_HDMI4_MHL
V5
CK-_HDMI4_MHL
AB1
AE0P
AVDD12_LVDS_3
AE0N
AVDD33_LVDS
AE1P
AE2N
AVSS12_LVDS_2
AECKP
AVSS12_LVDS_3
AECKN
AVSS33_LVDS_1
AE3N
AVSS33_LVDS_2
AE4P
AVSS33_LVDS_3
AE4N
REXT_VPLL
AO0P
AF1
AF2
AE3
AE4
AD3
AD4
J32
USB_DP2
J31
USB_DM2
Port was changed !!!!
USB_DM_P1
RXVN_1
USB_DP_P2
PHYLED1
USB_DM_P2
PHYLED0
K32
USB_DP1
K31
USB_DM1
0 R382
RXVP_1
AF13
AN10
WIFI_DP
0
AM10
OPT
C398
0.1uF
16V
C399
0.1uF
16V
OPT
AN8
C302
0.1uF
SC_R_IN_SOC
AVDD33_USB_P0P1P2
AVDD33_ETH
AVDD33_USB_P3
AVSS33_ELDO
AVSS33_USB_P1
AVSS33_LD
EPHY_RDN
SC_L_IN_SOC
AVSS33_USB_P3
CI_ADDR[5]
CI_ADDR[7]
CI_ADDR[8]
CI_ADDR[9]
TXB3P
AK4
AK1
AK2
AJ3
CI_ADDR[10]
TXBCLKN
MT5398_MCLKI
MT5398_MIVAL_ERR
TXBCLKP
MT5398_MISTRT
CI_ADDR[12]
CI_ADDR[13]
TXB2P
CI_ADDR[14]
MT5398_TS_OUT[0-7]
For PCB Pattern
TXB1P
AH3
HP_OUT
1.2K
R351
1.2K
HP_OUT
R369
1.2K
1.2K
R370
R352
C377
1200pF
HP_OUT
MT5398_TS_OUT[0]
C390
1200pF
HP_OUT
C383
HP_OUT
1200pF
HP_OUT
C395
1200pF
HP_OUT
HP_ROUT_MAIN
MT5398_TS_OUT[1]
HP_LOUT_MAIN
MT5398_TS_OUT[2]
MT5398_TS_OUT[3]
MT5398_TS_OUT[4]
MT5398_TS_OUT[5]
CI_DATA[0-7]
SCART_Lout_SOC
AL32
AN32
AM33
AM31
PC_L_IN_SOC TP380
C328
0.1uF
AM32
AK33
AC16
COMP1/AV1/DVI_R_IN_SOC
AC15
COMP1/AV1/DVI_L_IN_SOC
AVSS33_COM
AL33
AN33
AIN1_R_AADC
AR0_ADAC
AIN1_L_AADC
AL0_ADAC
AR1_ADAC
AIN3_R_AADC
AL1_ADAC
AK30
CI_DATA[0]
AJ29
CI_DATA[1]
AL2_ADAC
C365
10uF
10V
AC24
C362
0.1uF
ARC
AVSS33_AADC
C352
Close to MT5369
R380
1K
TU_S/N/Q_T/US/KR/TW
R331
1K
IF_N
TU_S/N/Q_T/US/KR/TW
Close to Tuner
TU_S/N/Q_T/US/KR/TW
R346
1K
0.01uF
R334
C337
1uF
AOMCLK
C363
1uF
10V
AK9
/CI_CD2
R367
100
R371
100
Don’t use as GPIO
AJ10
/CI_CD1
AUD_LRCK
AUD_MASTER_CLK
C389
22pF
OPT
C393
22pF
OPT
C396
33pF
OPT
PCM_RST
/PCM_REG
TP307
MT5398_TS_VAL
CI_A_VS1
MT5398_TS_CLK
/PCM_IRQA
/PCM_WAIT
33pF
TU_S/N/Q_T/US/KR/TW
VDD3V3
AM27
AN27
+1.2V_MTK_AVDD
C364
0.1uF
C351
0.1uF
AK18
ADCINP_DEMOD
HSYNC
ADCINN_DEMOD
VSYNC
RP
AN26
AVDD33_DEMOD
AVDD12_DEMOD
COM
AVSS33_DEMOD
VGA_SDA
AVSS12_DEMOD
VGA_SCL
SOG
AL28
IF_AGC
HP_OUT
L303
BLM18PG121SN1D
HP_LOUT
HP_LOUT_AMP
TU_S/N/Q_T/US/KR/TW
R342
10K
TU_S/N/Q_T/US/KR/TW
R332
10K
AL27
C355
0.047uF
TU_S/N/Q_T/US/KR/TW
Close to Tuner
C341
0.047uF
TU_S/N/Q_T/US/KR/TW
M28
Close to MT5369
PB1P
TP300
IF_AGC
RF_AGC
AK27
N26
Y1P
LOUTN
COM0
LOUTP
PB0P
PR0P
N27
OSCL2
OSDA2
PR1P
SOY1
AJ27
OSCL2
Y0P
OSDA2
SOY0
VDACX_OUT
HP_OUT
L302
BLM18PG121SN1D
For PCB Pattern
COMP1_Y/AV1_CVBS_SOC
TU_CVBS
AL19
AN20
AG22
AH22
R341
100
C360
0.047uF
AM25
R340
100
C359
0.047uF
AH26
TU_A_GLOBAL_6/7 TU_A_GLOBAL_6/7
C361
1uF
VDD3V3
AK25
AJ26
Near the SOC
AM26
TP311
TP359
TP360
TP361
TP362
TP363
TP364
SC_R_IN_SOC
TP365
SC_L_IN_SOC
TP366
TP303
SC_COM_SOC
TP306
SC_G_SOC
TP369
TP304
SC_R_SOC
TP370
SC_B_SOC
TP367
TP368
TP371
TP383
SC_FB_SOC
TP372
TP301
DTV/MNT_V_OUT_SOC
TP373
TP302
SCART_Rout_SOC
TP374
SCART_Lout_SOC
TP375
SC_G_SOC
PCM_5V_CTL
TP377
SC_R_SOC
SC_DET
TP378
SC_COM_SOC
AL22
AM21
SC_B_SOC
AN21
AM23
0.01uF
C371
51
R361
AL23
0.01uF
C372
51
R362
AL24
0.01uF
C373
51
R363
AN23
0.01uF
C374
51
R364
AK23
1500pF
C375
SC_FB_SOC
For PCB Pattern
COMP1_COM_SOC
COMP1_Pb_SOC
COMP1_Pr_SOC
OPT
AH24
0
AJ24
10
COMP1_Y/AV1_CVBS_SOC
R349
R350
DTV/MNT_V_OUT_SOC
VDD3V3
AVDD33_VIDEO
CVBS2P
CVBS1P
CVBS0P
AN18
AVDD12_RGB
+1.2V_MTK_AVDD
CVBS_COM
AC19
AVDD33_CVBS
Place at JACK SIDE
AVSS33_VDAC_BG
AVSS12_RGB
AK17
AE20
C382
0.1uF
AVSS33_VDAC
AB20
AB22
TP310
SC_CVBS_IN_SOC
AK22
AN25
CVBS3P
TP308
TP309
TP305
TP382
AK19
EU
AK26
HP_OUT
C331
0.22uF
10V
AM20
VDACY_OUT
SC_CVBS_IN_SOC
HP_ROUT
HP_ROUT_AMP
AL20
AL21
COM1
L26
HP_OUT
C332
0.22uF
10V
GP
BP
AN28
TP376
AL18
TP356
TP358
/PCM_OE
TU_S/N/Q_T/US/KR/TW
TP355
TP357
/PCM_IOWR
/PCM_WE
IC105
LGE2122[A2_M13]
TP353
/PCM_IORD
/PCM_CE1
MT5398_TS_SYNC
AOSDATA0
51
TP352
TP354
AUD_LRCH
C387
22pF
OPT
AH8
AOSDATA1
AUD_SCK
100
R368
AH9
AJ8
AOSDATA2
100
AF10
AK8
AOSDATA3
51
SC_ID_SOC
AJ9
AOLRCK
AOSDATA4
C358
0.1uF
TP351
V27
R366
TP347
TP348
TP349
TP350
MT5398_TS_IN[5]
TU_S/N/Q_T/US/KR/TW
R335
10V
TU_S/N/Q_T/US/KR/TW
C310
AH25
TU_A_GLOBAL_6/7
33pF
C336
1uF
10V
TU_S/N/Q_T/US/KR/TW
AOBCK
TP346
MT5398_TS_IN[4]
AG10
ASPDIF1
TP336
TP344
MT5398_TS_IN[6]
MT5398_TS_IN[7]
AG9
ALIN
ASPDIF0
MPXP
R339
2.2K
OPT
TU_S/N/Q_T/US/KR/TW
C312
SPDIF_OUT
AVDD3V3_AADC
AVDD33_AADC
AN31
VMID_AADC
IF_P
AC23
AVDD3V3_AADCAJ32
AVDD3V3_AADC
C305
1uF
10V
TUNER_SIF
TP333
TP335
TP343
Download PDF

advertising