DECT 6.0 2-Line Cordless Intercom Speakerphone

DECT 6.0 2-Line Cordless Intercom Speakerphone
DECT 6.0 2-Line Cordless
Intercom Speakerphone
User’s Guide
Important Information
Equipment Approval Information
Your telephone equipment is approved for connection to the Public
Switched Telephone Network and is in compliance with parts 15 and 68,
FCC Rules and Regulations and the Technical Requirements for Telephone
Terminal Equipment published by ACTA.
1
Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other
information, the US number and Ringer Equivalence Number (REN) for
the equipment. You must, upon request, provide this information to
your telephone company.
The REN is useful in determining the number of devices you may
connect to your telephone line and still have all of these devices ring
when your telephone number is called. In most (but not all) areas, the
sum of the RENs of all devices connected to one line should not exceed
5. To be certain of the number of devices you may connect to your line
as determined by the REN, you should contact your local telephone
company.
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Notes
•
This equipment may not be used on coin service provided by the
telephone company.
•
Party lines are subject to state tariffs, and therefore, you may not be
able to use your own telephone equipment if you are on a party line.
Check with your local telephone company.
•
Notice must be given to the telephone company upon permanent
disconnection of your telephone from your line.
•
If your home has specially wired alarm equipment connected to the
telephone line, ensure the installation of this product does not disable
your alarm equipment. If you have questions about what will
disable alarm equipment, consult your telephone company or a
qualified installer.
US Number is located on the cabinet bottom
REN number is located on the cabinet bottom
2
Important Information
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the
telephone network, the telephone company shall, where practicable,
notify you that temporary discontinuance of service may be required.
Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue
service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary
discontinuance; (2) afford you the opportunity to correct the situation;
and (3) inform you of your right to bring a complaint to the
Commission pursuant to procedures set forth in Subpart E of Part 68,
FCC Rules and Regulations.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business and not inconsistent with FCC
Rules and Regulations. If these changes are expected to affect the use
or performance of your telephone equipment, the telephone company
must give you adequate notice, in writing, to allow you to maintain
uninterrupted service.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference; and (2) This device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this phone.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna (that is, the antenna for
radio or television that is “receiving” the interference).
•
Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
•
Connect the telecommunications equipment into an outlet on a circuit
different from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your
dealer or an experienced radio/television technician for additional
suggestions. Also, the Federal Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve Radio/TV Interference
Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number
004-000-00345-4 when ordering copies.
3
Important Information
Warning: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Licensing
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility
This telephone system meets FCC standards for Hearing Aid Compatibility.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the
base unit and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.”
For body worn operation, this cordless handset has been tested and meets
the FCC RF exposure guidelines when used with the belt clip supplied with
this product. Use of other accessories may not ensure compliance with FCC
RF exposure guidelines.
Information for DECT Product
This telephone is compliant with the DECT 6.0 standard which
operates in the 1.92GHz to 1.93GHz frequency range.
Installation of this equipment is subject to notification and
coordination with UTAM. Any relocation of this equipment must
be coordinated through and approved by UTAM. UTAM may be contacted at
1-800-429-8826.
4
Table of Contents
EQUIPMENT APPROVAL INFORMATION ............. 2
ANSWERING A CALL ..............................22
SWITCHING BETWEEN THE SPEAKERPHONE,
INTERFERENCE INFORMATION ......................... 3
ANDSET, AND HEADSET MODE ............ 22
H
LICENSING ................................................ 4
BASE .................................................. 22
HEARING AID COMPATIBILITY ....................... 4
CORDLESS HANDSET ............................. 22
FCC RF RADIATION EXPOSURE STATEMENT .... 4
MUTE .................................................. 23
INFORMATION FOR DECT PRODUCT ............... 4
DO NOT DISTURB....................................... 23
INTRODUCTION ........................................... 7
FLASH ........................................................ 23
PARTS CHECKLIST ....................................... 7
INSERTING A PAUSE IN THE DIALING SEQUENCE
TELEPHONE JACK REQUIREMENTS................... 7
23
INSTALLATION ............................................ 8
REDIAL....................................................... 23
DIGITAL SECURITY SYSTEM .............................8
REVIEWING THE REDIAL NUMBERS............... 24
IMPORTANT INSTALLATION GUIDELINES ............ 8
STORING A REDIAL RECORD IN PHONE BOOK24
HANDSET LAYOUT ...................................... 9
TRANSFERRING A CALL TO ANOTHER EXTENSION
BASE LAYOUT.......................................... 10
24
INSTALLING THE PHONE ............................. 11
RECEIVING A TRANSFERRED CALL FROM ANOTHER
INSTALLING THE HANDSET BATTERY ...............11
EXTENSION............................................ 24
BASE STATION ............................................ 12
RINGER ON/OFF AND RINGER VOLUME ...... 25
PROGRAMMING THE PHONE ......................14
SPEAKERPHONE, HANDSET, AND HEADSET VOLSTANDBY SCREEN ....................................... 14
UME ..................................................... 25
PROGRAMMING FUNCTIONS ......................... 14
HOLD......................................................... 25
PHONE SETTING.......................................... 15
CONFERENCE CALLS .................................... 25
DATE/TIME ................................................. 15
JOIN A CALL IN PROGRESS: .................... 25
AUTO ANSWER (ONLY APPLICABLE FOR HANDSET)........
THREE-WAY CONFERENCE CALL BY AN INTER16
COM CALL: ........................................... 25
AUTO ANSWER INTERCOM (APPLICABLE FOR BASE
THREE-WAY CONFERENCE CALL WITH TWO
AND HANDSET) ...................................... 16
LINES: .................................................. 25
DIAL MODE (ONLY APPLICABLE FOR BASE) .... 16
FOUR-WAY CONFERENCE CALL (LINE 1 +
AREA CODE (ONLY APPLICABLE FOR BASE) .... 16
LINE 2 + 2 EXTENSION):...................... 26
REGISTRATION (ONLY APPLICABLE TO HANDSET)17
INTERCOM CALLS .....................................26
REGISTER ................................................... 17
ONE-TOUCH INTERCOM .............................. 26
REMOVE HANDSET ...................................... 17
ANSWERING AN INTERCOM CALL ................. 26
DE-REGISTER (ONLY APPLICABLE FOR BASE) . 17
PAGE ......................................................... 26
ADD HEADSET (ONLY APPLICABLE FOR BASE)..18
AUTO STANDBY .......................................... 27
SECOND CALL ALERT ................................. 18
HANDSET NAME (ONLY APPLICABLE FOR HANDSET)...... CALLER ID (CID) ...................................27
RECEIVING AND STORING CID RECORDS...... 27
18
REVIEWING CID RECORDS .......................... 27
UPDATE HANDSET LIST (ONLY APPLICABLE FOR
SAVING A CID RECORD TO PHONE BOOK
BASE) ................................................... 18
MEMORY.............................................. 28
DISPLAY SETTING ........................................ 19
DELETING A CID RECORD ........................... 28
LANGUAGE .................................................19
CONTRAST .................................................. 19
DELETING ALL CALL RECORDS ..................... 28
BACKLIGHT (ONLY APPLICABLE FOR BASE) ..... 19
DIALING BACK ........................................... 28
SOUND SETTING .........................................19
IF YOU PROGRAMMED YOUR LOCAL AREA
RING TONE..................................................20
CODE ................................................... 28
RING VOLUME ........................................... 20
IF YOU DID NOT PROGRAM YOUR LOCAL
KEY TONE .................................................. 20
AREA CODE ......................................... 29
VOICE MAIL .............................................. 20
CALL WAITING CALLER ID.......................... 29
RESTORE SETTING........................................ 21
MEMORY LOG AND PHONE BOOK (DIRECTORY)
TELEPHONE OPERATION ............................. 21
MEMORY ............................................29
MAKING CALLS WITH THE CORDLESS HANDSET21
ADDING PHONE BOOK ENTRIES ................... 30
MAKING CALLS IN THE SPEAKERPHONE MODE
(FROM THE BASE) .................................. 21
MAKING CALL IN THE SPEAKERPHONE MODE
(FROM THE HANDSET) ............................ 21
MAKING CALLS WITH A WIRED HEADSET...... 21
PRE-DIALING .............................................. 22
5
Table of Contents
STORING RECORD IN ONE-TOUCH DIALING (ONLY
APPLICABLE FOR BASE) ...........................30
REVIEWING PHONE BOOK RECORDS ............ 30
EDITING A PHONE BOOK RECORD ................ 31
COPYING A PHONE BOOK RECORD .............. 31
DELETING A PHONE BOOK RECORD ............. 32
DIALING A PHONE BOOK RECORD ............... 32
DIAL A PHONE BOOK RECORD WHILE IN TALK
MODE: ................................................. 32
DIAL A PHONE BOOK RECORD WHILE REVIEWING IT: ................................................. 32
VOICE MAIL SYSTEM .................................. 33
TO LISTEN TO YOUR VOICE MAIL MESSAGES
FROM THE BASE UNIT IN IDLE MODE. ...... 33
TO LISTEN TO YOUR VOICE MAIL MESSAGES
FROM THE HANDSET IN IDLE MODE. ........ 33
PROGRAMMING THE VOICE MAIL NUMBERS34
CHANGING THE BATTERY............................35
BATTERY SAFETY PRECAUTIONS ...................35
DISPLAY MESSAGES .................................36
HANDSET SOUND SIGNALS.........................36
TROUBLESHOOTING GUIDE ..........................37
TELEPHONE SOLUTIONS................................ 37
CALLER ID SOLUTIONS................................ 38
BATTERY..................................................... 38
GENERAL PRODUCT CARE ..........................39
CAUSES OF POOR RECEPTION .....................39
WARRANTY ASSISTANCE ............................40
LIMITED WARRANTY ................................. 41
6
Tone
Connections & Setup
Installation
Digital Security System
Your cordless phone uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
may cause or receive interference with nearby TVs, microwave ovens, and
VCRs. To minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV, microwave ovens,
or VCR. If such interference continues, move the cordless telephone farther
away from these appliances.
Certain other communications devices may also use the 1.9 GHz frequency
for communication, and, if not properly set, these devices may interfere
with each other and/or your new telephone. If you are concerned with
interference, please refer to the owner’s manual for these devices on how to
properly set channels to avoid interference. Typical devices that may use the
1.9 GHz frequency for communication include wireless audio/video senders,
wireless computer networks, multi-handset cordless telephone systems, and
some long-range cordless telephone systems.
Important Installation Guidelines
•
Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
•
Avoid areas of excessive dust, moisture and low temperature.
•
Avoid other cordless telephones or personal computers.
•
Never install telephone wiring during a lightning storm.
•
Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
•
Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
8
Connections & Setup
Handset Layout
Visual Indicator
display
3 Soft keys
DND/Privacy
(button)
Exit
(button)
VOL +/(buttons)
DIR
(button)
Spk
(Speaker button)
Headset Jack
CID
(button)
Off
(button)
Talk
(button)
* Tone
(button)
Mute/Del
(button)
Int/Hold
(button)
9
#Pause
(button)
Redial
(button)
Menu/Flash
(button)
Connections & Setup
Base Layout
Privacy
DND
Voicemail 1
Voicemail 2
New message
Indicate
Tone
10
Telefield NA Inc.approved Nickel-metal Hydride (Ni-MH) battery model
T-T104 (GP, 2.4V, 550mAh) , which is compatible with this unit.
Class (Classe) 2 Power source
T
Connections & Setup
4. If you want to mount the telephone on the wall, you can plug the 2
lines such as the below drawing;
Line 2
Line 1
-OR-
Line 2
-OR-
Line 1 + 2
13
Line 1
Sound Setting, Voice Mail
Programming the Telephone
Phone Setting
1. Make sure your phone is OFF (not in Talk mode).
2. Press the Menu button on HS or the MENU soft key (left) on BS to go
to the main menu.
3. Press VOL (+ or -) button to scroll to Phone Setting.
4. Press SELECT soft key (right) to confirm and you may program the
following items:
Date/Time (base only),
Auto Answer (handset only),
Auto Answer Intercom (both base and handset),
Dial Mode (base only),
Area Code (base only),
Registration (handset only),
De-Registration (base only),
2nd Call Alert (both base and handset),
Handset Name (handset only),
Update HS List (base only).
Add Headset (base only)
Date/Time
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to Date/Time.
.
2. Press SELECT Soft key.
3. LCD will display last-set time (or, if the device is new or has been reset to
default, the LCD will display 12:00AM 01/01/10)
4. Use the dial-pad to enter digits for the current time and date.
NOTE: Use DIR/CID button to move the cursor and the AM/PM softkey to
set the time AM or PM.
5. Press SAVE softkey to confirm the setting, a confirmation tone will
indicate that your selection has been saved.
NOTE: The Date/Time setting item only exists in base menu, handset Date/
Time should update automatically after it is set in the base.
15
Programming the Telephone
Auto Answer (only applicable for handset)
This option allows you to pick up the handset from base to answer an
incoming call without pressing the Talk/Spk/L1/L2 button.
When it is set to off, this function is disabled in this handset.
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Auto Answer.
2. Press SELECT soft key. Use the VOL (+ or -) button to scroll to your
selection. The default setting is Off.
3. Press SELECT soft key to save your selection.
Auto Answer Intercom (applicable for base and handset)
If it is set to on, this handset or base will auto answer the intercom call
when it receives an intercom call.
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to Auto Answer Int.
2. Press SELECT soft key. Use the VOL (+ or -) button to scroll to your
selection. The default setting is Off.
3. Press SELECT soft key to save your selection .
Dial Mode (only applicable for base)
The Dial Mode of Line 1 and Line 2 can be set separately.
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Dial mode.
2. Press SELECT soft key.
3. Use the VOL (- or +) button to select Line1 or line2, press Select softkey
to confirm, then use VOL(- or +) to scroll to your selection: Tone or Pulse
4. Press SELECT soft key to save your selection.
NOTE: The Dial mode only can be set in the base menu.
Area Code (only applicable for base)
The telephone uses the pre-programmed area code to determine the
number format to display when a valid Caller ID record is received. The
pre-programmed area code is also used for the Dialback feature.
From the Phone setting Menu:
1. Press the VOL (+ or -) button to scroll to the Area code.
2. Press SELECT soft key.
3. Use the touch-tone pad to enter your 3-digit area code.
4. Press SAVE soft key to save your selection.
16
Programming the Telephone
Registration (only applicable to handset)
A cordless handset will not operate until it is registered to the base. During
the registration process, keep the handset near the base. Up to 10 cordless
handsets can be registered to one base.
NOTE: If a handset has not been registered to the base, then the screen
displays “PRESS “REG” TO INITIATE REGISTRATION” once the handset has
been activated. Press the REG soft key to start the registration.
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to Registration.
2. Press SELECT soft key and you may program the following items:
Register and Remove handset.
Register
From the Registration Menu:
1. Press the VOL (+ or -) button to scroll to Register.
2. Press SELECT soft key. The screen displays Register HS Registering...
3. Press and hold the Page button on base for about 3 seconds.
4. “Registering” displays to indicate the base is now in registration mode.
5. If the registration is successful, the screen displays “Registration
complete” for 2 seconds and emits a confirmation tone.
6. If the registration is failed (i.e. timeout), the screen displays
“REGISTRATION FAILED!” for 2 seconds and emits an error tone.
Remove Handset
De-registration cancels registration. During the de-registration process,
keep the handset near the base.
WARNING: It is not recommended that a handset be
deregistered unless absolutely necessary because once a
handset is deregistered, that handset’s telephone features
cannot be used until the handset is re-registered.
From the Registration Menu:
1. Press the VOL (+ or -) button to scroll to the Remove handset.
2. Press SELECT soft key button. The screen displays “Remove handset?”.
3. Press the YES soft key to confirm de-registration. The screen displays
“Press “REG” to initiate registration” in the handset.
NOTE: You can press the REG soft key to enter the registation mode again.
De-Register (Only applicable for base)
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Deregistration.
2. Press SELECT soft key. The list of all registered handsets will be
displayed, and use the VOL (+ or -) button to scroll to your selection.
3. Press the SELECT soft key. The screen displays “Remove handset?”.
17
Programming the Telephone
4. Press YES soft key to confirm de-registration. The screen displays
“Saved” and then displays “Press “REG” to initiate registration” in the
handset.
Add Headset (only applicable for base)
NOTE: This wireless headset option is only compatible with the RCA 25065RE1.
From the Phone Setting Menu:
1. Press the vol(- or +) button to scroll to Add Headset;
2. Press the SELECT Sofykey. The screen will display Pairing...Please wait.
3. On the headset, press and hold the Talk On/Off button together with the
Volume+ button for 3 seconds. The LED indicators will begin blinking in
an alternate red and blue pattern.
4. If the registration is successful, a blue LED on the Headset will flash.
NOTE: Only one cordless Headset may pair with a base unit.
Second Call Alert
If it is set to On, you will hear the alert tone when you are in conversation
and there is an incoming call from another line.
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to 2ND Call Alert.
2. Press SELECT soft key. Use the VOL (+ or -) button to scroll to your
selection. The default setting is On.
3. Press SELECT soft key to save your selection.
Handset Name (only applicable for handset)
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Handset name.
2. Press SELECT soft key. The default name is Handset.
3. Use the touch-tone pad to enter a name (up to 13 characters). More
than one letter is stored in each of the number keys. For example, to
enter Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3
times for the letter I. Press the 5 key 3 times for the letter L. Press the 5
key 3 times for the second letter L, and press the 1 key to insert a space
between the first and last name. Press the 7 key 4 times for the letter
S; press the 6 key once for the letter M; press the 4 key 3 times for the
letter I; press the 8 key for the letter T; press the 4 key twice for the
letter H.
NOTE: If you make a mistake, press DIR/CID button to move the cursor
forward or backward, and then use the Mute/Del button to backspace and
delete one character at a time.
4. Press the SAVE soft key to save your name. You will hear a confirmation
tone.
Update Handset List (only applicable for base)
This function is used to update all registered handsets from the current
handset name list.
18
Programming the Telephone
From the Phone Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Update HS List.
2. Press SELECT soft key.
3. The latest handset name list stored in the base will be sent to all
registered handsets.
Display Setting
1. Make sure your phone is OFF (not in Talk mode).
2. Press the Menu button on HS or the MENU soft key on BS to go to the
main menu.
3. Press VOL (+ or -) button to scroll to Display Setting.
4. Press SELECT soft key to confirm and you may program the following
items: Language, Contrast and Backlight (base only).
Language
From the Display Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Language.
2. Press SELECT soft key.
3. Use the VOL (+ or -) button to select English, Francais or Espanol. The
default setting is English.
4. Press SELECT soft key to save your selection.
Contrast
From the Display Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Contrast.
2. Press SELECT soft key. The “MIN and MAX” contrast scale displays on the
screen.
3. Use the VOL (+ or -) button to adjust the contrast. The display instantly
adjusts with each press of the VOL (+ or -) button.
4. Press SELECT soft key to save the desired contrast level.
Backlight (Only applicable for base)
From the Display Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Backlight.
2. Press SELECT soft key and use the VOL (+ or -) button to select Always
On or Automatic.
3. Press SELECT soft key to save your selection.
Sound Setting
1. Make sure your phone is OFF (not in Talk mode).
2. Press the Menu button on HS or the MENU soft key on BS to go to the
main menu.
3. Press VOL (+ or -) button to scroll to Sound Setting.
4. Press SELECT soft key to confirm and you may program the following
items in base and handset: Ring Tone, Ring Volume and Key Tone.
19
Telephone Operation
Ring Tone
There are 8 tone levels for your selection. They are Melody 1 to 8 for line 1
and line 2 respectively.
From the Sound Setting Menu:
1. Press the VOL (+ or -) button to scroll to the Ring Tone.
2. Press SELECT soft key.
3. Use the VOL (+ or -) button to select Line1 or line2, press Select softkey
to confirm,then use VOL(- or +) to scroll to your selection. The default
setting is Melody 1 for line1 and Melody 2 for line2.
4. Press SELECT soft key to save your selection.
Ring Volume
There are 5 Volume levels and OFF for your selection. The Ring Volume can
be set individually for each line.
From the Sound Settings Menu:
1. Press the VOL (+ or -) button to scroll to the Ring Volume.
2. Press SELECT soft key.
3. Use the VOL (+ or -) button to select Line1 or line2, press Select softkey
to confirm,then use VOL(- or +) to scroll to your selection.The default
setting is VOL 3.
4. Press SELECT soft key to save your selection.
Key Tone
From the Sound Settings Menu:
1. Press the VOL (+ or -) button to scroll to the Key Tone.
2. Press SELECT soft key. Use the VOL (+ or -) button to select On or Off.
3. Press SELECT soft key to save your selection.
Voice Mail
This feature is used to conveniently access the voicemail feature offered by
your telephone service provider.
NOTE: You must subscribe to telephone service provider-offered voicemail on at least one phone line in order for this feature to operate.
1. Make sure your phone is in idle mode. (not in Talk mode)
2. Press the MENU Soft key (left) to go to the main menu.
3. Press VOL (- or +) button to scroll to Voice Mail.
4. Press SELECT Soft key (right) to confirm and you may program t he
following items:
Call VM
Settings
Call VM
From the Voice Mail Menu:
1. Press VOL (- or +) button to scroll to Call VM.
2. Press SELECT Soft key
3. Use the VOL (- or +) button to toggle between Line 1 and Line 2 and press
SELECT soft key to select.
4. The phone will dial your voicemail access number. You may proceed to
access your voicemail per your service provider’s instructions.
Settings
From the Voice Mail Menu:
1. Press VOL (- or +) button to scroll to Settings.
20
2. Press SELECT Soft key
3. Use the VOL (- or +) button to toggle between Line 1 and Line 2 and
press SELECT soft key to select.
4. Use the dial pad to enter the call-in access number for your voicemail.
Press Delete button to backspace and delete numbers, if necessary.
5. Press SAVE Soft key.
6. A confirmation tone will indicate that your selection has been saved.
Restore Setting
The feature allows you to reset some menu settings to the original default
settings.
1. Press Menu button on handset or MENU soft key on the base.
2. Press the VOL (- or +) button to scroll to Restore Setting.
3. Press SELECT soft key. “LOAD TO DEFAULT?” displays on the screen.
4. Press YES soft key to let unit reset to default setting; once finished, the
unit will emit a short beep prompt, and after the base shows " please wait
..." in the display for about 3 seconds. then reset the unit automatically.
5. If you do not want to reset, press the NO soft key.
Telephone Operation
Making Calls with the Cordless Handset
1. Press the Talk button, the unit will pick the first available line for you.
-ORPress Line 1 or Line 2 soft key to select a line you wanted.
2. Wait for a dial tone then dial the phone number.
3. Press the End button when finished.
Press the Line1 or Line2 Softkey to select a specific line. The Handset
will activate the ear piece. Then press the SPK button to switch to the
speakerphone mode.
2.
3.
a wired
Telephone Operation
CAUTION: For servicing or replacement, you can purchase a suitable headset
through service centre or retailer shop.
Pre-dialing
1. With the phone idle, manually enter the telephone number. The screen
displays the telephone number.
2. Press the DIAL soft key (on base only), Speaker button, Talk button
(handset only), or Line 1 or Line 2 button to take a line, and then the
telephone number will be dialed out.
Answering a Call
For cordless handset:
1. Press the Talk button to answer the call in receiver mode,
-OR2. Press the Spk button to answer the call in speakerphone mode,
-OR3. Press the corresponding LINE soft key to answer the call in receiver
mode.
4. When finished, press END button.
For the base:
1. Press the Speaker button to answer the call in speakerphone mode,
-OR2. Press the corresponding Line button to answer the call in speakerphone
mode,
-OR3. Press the Headset button to answer the call in headset mode.
4. When finished, press Speaker button (in speakerphone) or Headset
button (in headset mode) to end the call.
NOTE: If you have set the Auto Answer as On in the cordless handset, you
can answer the call directly by picking up this handset from the base,
without pressing any buttons.
NOTE: Adjust the Volume by pressing the VOL (+ or -) button during a call.
Switching Between the Speakerphone, Handset, and Headset
Mode
Base
To switch to the speakerphone, press Speaker button. The speakerphone
indicator illuminates.
To switch to the headset, press the Headset button to enable the headset,
and the headset indicator illuminates.
Cordless Handset
To switch to the speakerphone, press Spk button.
If the headset is plug in, press Talk button to switch to headset.
If the headset is not plug in, press Talk button to switch to cordless
handset’s receiver.
22
Telephone Operation
Mute
To have a private, off-line conversation, use the Mute feature. The party on
the other end of the line cannot hear you, but you can still hear them.
1. Press Mute button to activate the mute feature.
NOTE: When using the mute feature on the base, the indicator will
illuminate when the mute is activated.
2. Press the Mute button again to de-activate.
Do Not Disturb
This feature is set at individual telephones to disable (silence) an incoming
ring signal, intercom ring. When there is an incoming call or an intercom
call, the status indicators function as normal but the phone will not ring.
1. When the unit is idle, press the DND/Privacy button. The last setting is
displayed.
2. Use the VOL (+ or -) button to select the duration. You may choose
from 15 minutes, 30 minutes, 45 minutes, 1 hour, or 2 hours and
increase the duration by 1-hour intervals up to 24 hours.
3. Press the SELECT soft key to confirm. The indicator (on the base) blinks
and the screen displays how long the ringer will be disabled.
4. To cancel, press DND/Privacy button again.
NOTE: If Intercom Auto Answer is activated, the unit automatically answers
the intercom call even if the Do Not Disturb function is activated.
Flash
Use the Flash button to activate custom calling services such as call
waiting or call forwarding, which are available through your local phone
company.
Inserting a Pause in the Dialing Sequence
Press the #Pause button twice to insert a delay in dialing sequence when a
pause is needed to wait for a dial tone (for example, after you dial 9 for an
outside line, or to wait for a computer access tone.) Each pause counts as
one digit in the dialing sequence, and the screen displays “P”.
Redial
1. Press the Talk button, or press the Speaker button (speakerphone mode),
or press the Headset button (headset mode) and the first available line
will go off hook. If both lines are available, Line 1 will be used.
-ORPress a Line button to select a line.
2. Press the Redial button. The redial number list (last 3 previously dialed
numbers) is displayed.
3. Use the VOL (+ or -) button to select the number. Press the DIAL soft
key to dial out the number.
NOTE: The Redial function will not operate if the number to be redialed
contains more than 32 digits. If the number is longer than that, you will
hear an error tone.
23
Telephone Operation
Reviewing the Redial Numbers
Your phone records up to three previously dialed phone numbers.
1. When the phone is idle, press the Redial button.
2. Use the VOL (+ or -) button to view the last three previously dialed
numbers.
3. While the preferred number is displayed, press the Spk, Talk, or a Line
button to dial the phone number.
NOTE: If you do not select a Line button, the line is automatically held and
the number is dialed accordingly.
Storing a Redial Record in Phone Book
1. Make sure the phone is OFF (not in Talk mode).
2. Press the Redial button, then use the VOL (+ or -) button to scroll to
the desired redial number.
3. Press the SAVE soft key.
4. The screen displays “Enter Name”. Input a name. Please refer to section
“Handset Name” for name editing method.
NOTE: A name must be input otherwise the record cannot be stored.
5. Press the SAVE soft key. The desired redial number is displayed on the
screen.
6. You can edit the telephone number.
7. Press SAVE soft key to enter the VIP Tone Melody selection.
8. Use VOL(- or +) button to select the VIP tone melody and then press
Select soft key to confirm the selection.
Transferring a Call to Another Extension
1. Press XFER soft key when the phone is in Talk mode.
2. Use VOL (+ or -) to select the desired handset or base you want to
transfer to, and then press the SELECT soft key.
3. The unit will intercom the selected handset or base, and it will ring for
this intercom call. At this moment, the call is on hold.
4. Once the selected handset answers the intercom call, after the call
transfer initialized unit hangs up, the call can be transferred to the
desired handset or base, or press the CONF soft key to enter conference
call mode.
5. If the selected unit rejects the intercom call, the call transfer initialized
displays ”Unavailable” on the screen for 3 seconds, and then you can
pick up the call again.
Receiving a Transferred Call from Another Extension
If the unit receives a transfer call paging, the screen displays “Intercom
call from base/Handset X”. Press the Talk button (handset only) or Speaker
button (both base and handset) to answer the call.
If you press the REJECT soft key, the intercom paging will be stopped.
24
Telephone Operation
Ringer On/Off and Ringer Volume
1. Make sure the phone is in idle mode.
2. Press the VOL (+ or -) button to activate the ringer Volume setting. Press
Line1 or Line2 softkey to select the direct line which you want to set,
then use the VOL (- or +) button to scroll to your selection. The default
setting is VOL 3.
3. Press the SELECT soft key to save your selection.
NOTE: If you choose the ringer OFF, the screen displays “L1/L2 RINGER OFF”.
Speakerphone, Handset, and Headset Volume
While the phone is in use, during the desired mode, press the VOL (+ or -)
buttons until you reach a comfortable listening level. The phone stores the
setting after the last button pressed.
Hold
In Talk mode, press the Hold button to hold the line. The screen displays
“Line X ON HOLD”, and the line icon will flash. On the base, the Line button
indicator will flash also.
When the line is on hold, the hold alert tone will be emitted.
Press the corresponding LINE soft key (on handset), or the Line button (on
base) to release the hold and pick up the call again.
Conference Calls
This system can support 3-way and 4-way conference calls.
Join a call in progress:
1. While a call is in progress, another user can join that call by
pressing the corresponding Line button on the base unit or soft key in
the handset. Both parties on the original call will hear a tone to alert
them someone else has joined the call.
NOTE: If the privacy feature is On for the original call, the call cannot be
joined by another user.
Three-way conference call by an intercom call:
1. While on a call, press the Intercom button and then select the desired
handset or base to intercom.
2. The selected handset or base will emit a page tone. The user can press
the Talk button on the handset or the Speaker button on the base to
answer the intercom call page.
3. The originating caller can then press the CONF soft key displayed on the
screen to establish a 3-way conference between the external caller and
the intercom call.
Three-way conference call with two lines:
1. During a call on Line 1, press the Hold button to put the call on hold.
2. Press the Line 2 button or soft key on the handset to get a dial tone.
Dial the number, and then talk to the other person.
3. The originating caller can then press the CONF soft key displayed on the
screen to establish a 3-way conference between the two lines.
25
Telephone Operation
Four-way conference call (Line 1 + Line 2 + 2 extension):
1. Once the base unit or handset has both Line 1 and 2 on hold, press the
Intercom button and then select the desired handset or base to
intercom.
2. The selected handset or base will emit a page tone. The user can press
the Talk button on the handset or the Speaker button on the base to
answer the intercom call page.
3. The originating caller can then press the CONF soft key displayed on
the screen to initiate a conference. Since Line 1 and 2 are both on hold,
the user will be prompted to select Line 1, Line 2 or Both to conference
with. The user can then use the soft keys to select the desired option.
If the BOTH soft key is selected a 4-way conference is established
between the originating caller, both lines and the intercom call.
Intercom Calls
One-Touch Intercom
1. On the base, in idle mode, press any One-Touch Intercom button (1-10)
for the station you want to intercom with. One-Touch button #1
represents handset 01, #2 represents handset 02, etc.
The Intercom paging ring will be emitted.
-ORYou may press the Intercom button, then press the Intercom/Memory
button (1-10) for the stations you want to intercom with.
-ORPress the Intercom button, and all the registered handsets and the base
except itself list in the log, use the VOL (+ or -) key to scroll to the station
you want to intercom with, and then press SELECT soft key to confirm.
NOTE: To abort intercom call, press the STOP soft key.
NOTE: If the receiving station does not answer within 30 seconds, the
intercom call is cancelled. You will hear an error tone and the screen
displays “Unavailable”.
Answering an Intercom Call
When you receive an Intercom call, the screen displays the Caller’s Name
and Phone ID.
If you want to answer with the speakerphone, press the Speaker button. If
you want to answer by headset, press the Headset button on the base or
the Talk button on the handset. The headset must be already connected.
If you do not want to answer this intercom call, press the REJECT soft key.
Page
The page feature helps you locate a misplaced handset.
1. Press the Page button on the base. The handset beeps and the Visual
Indicator on the handset flashes. The screen displays “Paging from Base”.
2. To cancel the page, press the Page button on the base, or press STOP
soft key on the base, or press Exit key on the base, or press any key on
the handset. Otherwise the paging will last for 2 minutes.
26
Caller ID
Auto Standby
If you place the handset in the cradle while the handset is off the hook
(during a call), the call is automatically disconnected.
Caller ID (CID)
IMPORTANT: In order to use this unit’s Caller ID features, you must subscribe
to either the standard Name/Number Caller ID Service or Call Waiting Caller
ID Service. To know who is calling while you are on the phone, you must
subscribe to Call Waiting Caller ID Service.
When the unit receives an incoming call with CID information, the CID can
be displayed on the base and handsets.
Base Display
L1
LINE1
LINE2
Handset Display
Receiving and Storing CID Records
This unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date and time;
or the name, phone number, date and time. The unit can store up to 99
records for later review. When the memory is full, a new call automatically
replaces the oldest call in memory. The screen displays “NEW” for calls
received that have not been reviewed. The line number for the call received
is also displayed.
If two incoming calls come in at the same time, the line1 and line2 phone
numbers shows on the display separately.
Reviewing CID Records
•
Press CID button, and then use the VOL (+ or -) button to scroll through
the call records.
•
When you scroll to the start/end of the unit emit a warning tone and
then scroll to the end or the start of the record.
•
When reviewing the CID records, the record number is also displayed to
the right of the time along with the FORMAT and STORE soft keys.
27
Caller ID
Saving a CID Record to Phone Book Memory
1. While viewing a CID record, press the STORE soft key.
2. The name displays on the screen. You can edit it. After editing, press the
SAVE soft key.
3. The number displays on the screen. You can edit it. After editing, press
the SAVE soft key.
4. You can select the ring melody for this phone number. Use the VOL
(+ or -) button to scroll to your selection, and then press the SELECT
soft key to save.
NOTE: If you want to change the format of the CID number and save it in the
phonebook, press the FORMAT soft key to format the CID number first before
pressing the STORE soft key.
NOTE: You cannot skip the name editing. If it is empty in the name field, you
cannot press the SAVE soft key to go to number editing.
Deleting a CID Record
Press the Delete button to delete the record. The screen displays “DELETE?”.
Press the OK soft key to confirm. The unit will emit a confirm tone.
Deleting All Call Records
This feature allows you to clear all CID records at once.
1. While viewing a CID record, press and hold the Delete button.
The screen displays “Delete All?”
.
2. Press OK soft key to confirm. A confirm tone emit and Empty displays
for 3 seconds.
Dialing Back
When reviewing CID records, you can dial back the numbers displayed on
the screen by pressing the Headset button, or the Talk button, or the Spk
button or the Line 1 or Line 2 button.
If You Programmed Your Local Area Code
1. Use the CID button to display the number you want to dial.
2. If you see a number with 7 digits (i.e. 555-1234), then the call was
received from within your area code. However, this does not guarantee
the call is a local call. If you see a number with 11 digits
(i.e.1-234-555-1234), then the call received was not from your area
code.
3. To adjust the phone number format, use the FORMAT soft key. For
instance, a 7-digit local number sometimes cannot be dialed because it
requires a 10-digit or 11-digit format. Use the FORMAT soft key to scroll
through 7, 10 and 11-digit numbers.
28
Memory/Phone Book
Number of digits
Explanation
7-digits:
7-digit telephone number
10-digits:
3-digit area code
+7-digit telephone
number
11-digits:
Example
(i.e.555-5555)
(i.e.425-555-5555)
long distance code 1
(i.e. 1-425-555-5555)
+3-digit area code
+7-digit telephone number
4. To dial the displayed number, select a Line or press Talk, Spk, or
Headset button.
If You Did Not Program Your Local Area Code
1. Use the CID button to display the number you want to dial. You will
only see 10-digit numbers (i.e. 234-555-1234).
2. Press Talk, Spk, Headset button or select a Line to dial back. You may
adjust the number format by pressing the FORMAT soft key before
dialing.
Call Waiting Caller ID
This feature allows you to see who is calling when you hear the call waiting
beep. The caller identification information is displayed on the screen after
you hear the tone.
•
Press the Flash button to put the person to whom you’re talking on
hold and answer the incoming call.
IMPORTANT: To use all the features of this unit, you must subscribe to either
the standard Name/Number Caller ID Service or Caller ID with Call Waiting
Service. To know who is calling while you are on the phone, you must
subscribe to Caller ID with Call Waiting Service.
Memory Log and Phone Book (Directory) Memory
You may store data in the Phone Book Directory (up to 99 records) or an
Intercom/Memory (10 buttons located to the right of the number pad on
the base). The Phone Book and each Intercom/Memory Log stores up to 16
characters and 32 digits.
The records are stored by alphabetic ascending order.
29
Memory/Phone Book
Adding Phone Book Entries
1. Make sure the phone is OFF (not in Talk mode).
2. Press the DIR button.
3. Press the NEW soft key. The screen displays “Enter Name”. Please refer
to section “Handset Name” for name editing method.
4. Press SAVE soft key. The screen displays “Enter Number”.
5. Use the touch-tone pad to input a telephone number.
TIP: Press the #Pause button twice to insert a pause in a number if
necessary.
6. Press the SAVE soft key to enter VIP tone melody selection.
7. Use VOL (+ or -) button to scroll to the selection and press SELECT soft
key to complete.
NOTE: If the screen displays “Memory full”, you should delete one or more
unnecessary records and repeat above steps to continue the call record
storage.
Storing Record in One-Touch Dialing
(Only applicable for base)
1. Make sure the phone is OFF (not in Talk mode).
2. Press STORE soft key.
3. The screen displays “Select Button Location”. Press a One-Touch button
(1-10) to save the record in that memory location.
NOTE: If there is a record stored in selected memory location. Press REPLAC
soft key to confirm overwrite or press the BACK soft key, then repeat the step
1~3 to select a new location.
4. The screen displays “Enter Name”. Please refer to section “Handset
Name” for name editing method.
5. Press SAVE soft key. The screen displays “Enter Number”.
6. Use the touch-tone pad to input a telephone number.
TIP: Press the #Pause button twice to insert a pause in a number if
necessary.
7. Press the SAVE soft key to save.
Reviewing Phone Book Records
1. Make sure the phone is OFF (not in Talk mode).
2. Press the DIR button.
3. Press the VOL (+ or -) button to scroll through the records,
-ORPress the number keys to go to the name of the records started with
the corresponding character.
4. Then you can press Menu softkey and then use VOL(- or +) to select
View to review the direct record.
30
Memory/Phone Book
Editing a Phone Book Record
1. When reviewing the phone book records, use the VOL (+ or -) button or
the number keys to scroll to the desired record.
2. Press Menu soft key and then use VOL(- or +) to select Edit Entry. You
may now change the name, if desired. Please refer to section“Handset
Name” for name editing method.
3. Press SAVE soft key to proceed to number change. You may now change
the number, if desired.
4. Press SAVE soft key to proceed to VIP Tone Melody selection. You may
use VOL (+ or -) key to scroll to the selection you desired.
5. Press SELECT soft key to complete.
NOTE: Press the BACK soft key to keep the previous setting (making no
changes).
Copying a Phone Book Record
You can copy one phone book record or the whole phone book from the
handset extension to the base or from the base to desired handset
extension.
In the extension handset:
1. While viewing the phone book record, press the COPY soft key.
2. The screen displays “Copy Current Record or Entire Directory?”. Press the
CURR soft key to copy the current record or press the ENTIRE soft key
to copy the whole phone book.
3. After copying is finished, the prompt message The screen displays
“Record Copied to Base Unit!”.
In the Base Unit:
1. While viewing the phone book record, press the COPY soft key.
2. The screen displays “Copy Current Record or Entire Directory?”. Press the
CURR soft key to copy the current record or press the ENTIRE soft key
to copy the whole phone book.
3. The extension list will be displayed. Use the VOL (+ or -) button to
select the desired extension handset for the record to be copied to.
4. Press the SELECT soft key.
5. After copying is finished,the screen displays “Record Copied!”, and
“Saved”.
31
Memory/Phone Book
Deleting a Phone Book Record
1. When reviewing the phone book records list, use the VOL (+ or -)
button or the number keys to scroll to the desired record.
2. Press the delete key on the phone to delete the record.
3. The screen displays “Delete?”.
4. Press the OK soft key to confirm the deletion.
Deleting All Phone Book Records
1. Press the DIR button to activate the phone book record list.
2. Press and hold the Delete button on the phone until “DELETE ALL?”
shows in the display.
3. Press the OK soft key to confirm the deletion.
4. “EMPTY ” shows in the display.
Dialing a Phone Book Record
Dial a phone book record while in Talk mode:
1. Make sure the phone is ON (in Talk mode) by pressing the Talk, Spk
button, or selecting a Line.
2. Press the DIR button to access the phone book.
3. Use the VOL (+ or -) button or the number keys to scroll to the desired
record.
4. Press the DIAL soft key to dial the number.
-ORDial a phone book record while reviewing it:
1. Make sure the phone is OFF (not in Talk mode).
2. Press the Phonebook button to access the phone book.
3. Use the VOL (+ or -) button or the number keys to scroll to the desired
record.
4. Press the Talk or Spk button on the handset or press the Speaker or
Line 1/2 on the base. The number dials automatically.
32
Voice Mail System
Voice Mail System
Provided your phone company offers voice messaging service and you
subscribe to it, the NEW MSG indicator on the base and the Visual Indicator
on the top of the handset flashes to indicate a message is waiting. The
screen displays “L1 MSG Waiting” or “L2 MSG Waiting” to indicate which
line has voice mail waiting. If both lines have new voice mail messages, the
display shows "L1 MSG Waiting" & "L2 MSG Waiting" alternately. It stops
flashing after the message is reviewed.
NOTE: To deactivate the New Message indicator; Press the Delete button once
during the BS display shows "Lx MSG Waiting", then the indicator will be off.
IMPORTANT: You must have the voice mail access code
programmed for this feature to work. See the “Programming
the Voice mail numbers” section. If there is no voice mail
number stored, the system will emit an error tone.
To listen to your voice mail messages from the base unit in idle mode.
1. Press VOICE MAIL 1 for line 1 voicemail or VOICE MAIL 2 for line 2
voicemail.
2. The base unit activates the speaker with the corresponding line and
auto dials the pre-programmed voice mail access number/code to
access the voice mail stored at the phone company.
3. Once the phone company voice mail system answers the call, additional
digits such as a pin code may be dialed.
4. The screen displays “the dialed numbers” and the call timer.
To listen to your voice mail messages from the handset in idle mode.
1. Press VM soft key.
1
2. The screen displays “VOICE MAIL: SELECT LINE”. Press the Line1 softkey to
access line 1 voice mail and Line2 softkey to access line 2 voice mail.
3. The handset activates the receiver with the corresponding line and auto
dials the pre-programmed voice mail access number/code to access the
voice mail stored at the phone company.
4. Once the phone company voice mail system answers the call, additional
digits such as a pin code may be dialed.
5. The screen displays “the dialed numbers” and the call timer.
33
Voice Mail System
Programming the Voice mail numbers
1. Make sure your phone is OFF (not in talk mode).
2. Press STORE soft key on base. The screen displays “SELECT BUTTON
LOCATION”.
3. Press one of the two Voice mail buttons.
4.
5.
6.
7.
The screen displays “ENTER NUMBER:”
Enter the phone number.
Press the SAVE soft key to save the number.
The unit emit a confirm tone and then returns to the idle mode
Note:
-
User can press the Delete button to delete the current digit and move
the curser to the left one position.
-
Press the Left () and Right () arrows to move the curser left and
right to edit input.
-
Press PAUSE twice (displayed as “P”) to enter a pause in the dialing
sequence.
-
If the user does not enter anything and then presses SAVE, the contents
will be cleared.
Note: You can also access the Voice mail center from the Voice mail
sub-Menu, please refer to the Voice mail section.
34
only the Telefield NA Inc. approved Nickel-metal Hydride (NiMH) battery model T-T104 (GP, 2.4V, 550mAh) , which is
compatible with this unit.
Display Messages
Display Messages
The following messages show the status of the phone, provides Caller ID
information, or helps you set up and use your phone.
DELETE ALL?
Prompt asking if you want to erase all records.
DELETE?
Prompt asking if you want to erase the current record.
ENTER NAME
Prompt telling you to enter a name.
ENTER NUMBER
Prompt telling you to enter a telephone number.
NEW CALLS
Indicates call or calls which have not been reviewed.
HANDSET NAME
Prompt telling you to enter a user name for the hand
set.
UNAVAILABLE
Indicates that the function you want to initialize
cannot work at that moment or the function being
worked cannot continue. The system is busy or some
other higher priority function is being performed.
For example, the message playback function will be
stopped when there is an incoming call.
NO LINE
Indicates that the telephone line is not connected.
LINE IN USE
Display on handset while the line is in use.
EMPTY
Indicates there are no CID records in memory.
OUT OF RANGE
Indicates handset is too far away from the base, and
the handset is searching for the base.
BLOCKED
Indicates the person is calling from a number which is
blocked from transmission.
UNKNOWN
Indicates incoming call is from an area not serviced by
CID or the CID information was not sent.
Handset Sound Signals
Signal
A long warbling tone (with ringer on)
Meaning
Signals an incoming call
Two short beeps (several times)
Page signal
One beep every 14 seconds
Low battery warning
One long beep after press one key
Confirm
A short warbling tone (with ringer on)
Error
36
Troubleshooting Guide
Troubleshooting Guide
Telephone Solutions
No dial tone
• Check or repeat installation steps:
Make sure the base power cord is connected to a working electrical
outlet. Make sure the telephone line cord is connected to the base and
the wall jack.
•
Connect another phone to the same jack. If it doesn’t work, the
problem might be your wiring or local service.
•
The handset may be out of range of the base. Move closer to the base.
•
Make sure the battery is properly charged (for 14 hours).
Dial tone is ok, but can’t dial out
• Make sure the type of phone service you are subscribed to is TONE or
PULSE.
Handset does not ring
• Make sure the handset ringer is set to On.
•
The handset may be out of range of the base. Move closer to the base.
•
You may have too many extension phones on your line. Try unplugging
some extensions.
•
Check for a dial tone. If no dial tone is heard, see “No dial tone”.
You experience static, noise, or fading in and out
• The handset may be out of range of the base. Move closer to base.
•
Make sure base is not plugged into an electrical outlet with another
household appliance. If necessary, relocate the base.
•
Charge the battery (for 14 hours).
Memory dialing doesn’t work
• Did you follow proper dialing sequence?
Unit locks up and no communication between the base and cordless
handset
• Unplug the power adaptor from the electrical outlet and the bottom of
the base. Remove the handset battery. Wait for 30 seconds and plug the
power adaptor back into the base and electrical outlet. Reconnect the
battery and charge for 14 hours.
37
Troubleshooting Guide
“Out of Range...” is displayed on the screen
• Move the handset closer to the base.
•
Make sure the base power cord is connected to a working electrical
outlet.
Date/Time setting is restored to default setting
• May be caused by power failure. Set Date/Time again.
Caller ID Solutions
No Display
• Charge the battery (for 14 hours). Or replace the battery.
•
Make sure the unit is connected to a non-switched electrical outlet.
Disconnect the power adaptor from the base and reconnect it.
No Caller ID
• You must be subscribed to the standard Name/Number Caller ID service
from your local telephone company to receive CID information.
Battery
If you experience any of the following problems, even after recharging the
battery, you may need to replace the battery pack:
•
Short talk time
•
Poor sound quality
•
Limited range
38
Troubleshooting Guide
General Product Care
To keep your unit working and looking good, follow these guidelines:
•
Avoid dropping the handset, as well as other rough treatment to the
phone.
•
Clean the phone with a soft cloth.
•
Never use strong cleaning agents, paint thinner, abrasive powder,
alcohol, or other chemical products to clean the unit. Doing so will
damage the finish.
•
Retain the original packaging in case you need to ship the phone at a
later date.
•
Periodically clean the charge contacts on the handset and base with a
clean pencil eraser.
Causes of Poor Reception
•
Aluminum siding.
•
Foil backing on insulation.
•
Heating ducts and other metal construction that can shield radio
signals.
•
You’re too close to appliances such as microwaves, stoves, computers,
etc.
•
Atmospheric conditions, such as strong storms.
•
Base is installed in the basement or lower floor of the house.
•
Base is plugged into AC outlet with other electronic devices.
•
Baby monitor is using the same frequency.
•
Handset battery is low.
•
You’re out of range of the base.
39
by telefield NA Inc. could viod the user’s authority to operate this product.
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• Two years, from date of purchase.
What we will do:
• Provide you with a replacement unit. The exchange unit is under warranty
for the remainder of the original product's warranty period.
How you get service:
• Locate your proof of purchase in the form of a bill of sale or receipted invoice
which is evidence that the product is within the warranty period. Proof of warranty eligibility is required and must be presented to obtain warranty service.
• Contact RCA Customer Care at (800) 511-3180. Our representatives will help
you troubleshoot and diagnose the problem. As you may be asked to disconnect
your RCA telephone from it's power source, you must call from another
telephone. If the issue cannot be resolved by our Customer Care Team, you will
be issued an RMA (Return Merchandise Authorization) number and be given
instructions on how to submit your proof-of-purchase paperwork and where to
send your defective merchandise.
• You will be responsible for shipping the defective unit back to our warranty
fulfiIIment center at your own expense. You are responsible for damage or loss
during shipment so insuring the product during return shipping is highly
recommended.
• We will ship a replacement to you freight pre-paid.
What your warranty does not cover:
• Customer instruction. (Your Instruction Book provides information regarding
operating instructions and user controls. Additionally, our Customer Care Center
is staffed 24x7 with product experts that can assist you with any questions that
may arise during setup and use of your RCA telephone.)
• Installation and setup service adjustments
• Batteries
• Damage from misuse or neglect
• Products that have been modified of serviced outside the USA
• Products purchased from non-authorized retailers, dealers or resellers
• Products purchased or serviced outside the USA
• Acts of nature,such as, but not limited to lightning damage
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit.
lt will make it easierto contact you should it ever be necessary. The return of the
card is not required for warranty coverage.
TELEFIELD NA INC.
TELEFIELD NA INC.
OREGON
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have
other rights that vary from state to state.
If you purchased your product outside the USA, Mexico or Canada:
This warranty does not apply. Contact your dealer for warranty information.
Add Headset (only applicable for base) 18
Language
17
19
Pre-dialing
22
Visit the RCA web site at: www.rca4business.com
Please do not send any products to the Oregon address listed in this
Telefield NA Inc.
4915 SW Griffith DR. #302
Beaverton, OR 97005
RCA is a trademark of RCA Trademark Management S.A.,
used under license.
© 2012. All rights reserved.
Model 25212
T0000109 (REV.2 E)
12-32
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement