LG | AS-H076PB/D/M/WL1 | User's Manual | LG AS-H076PB/D/M/WL1 User's Manual

website http://www.lgservice.com
LG
LG Room
Air Conditioner
SERVICE MANUAL
MODELS: AS-H076PB/D/M/WL1
AS-H096PB/D/M/WL1
A-12AH series
CAUTION
• BEFORE SERVICING THE UNIT, READ THE SAFETY
PRECAUTIONS IN THIS MANUAL.
• ONLY FOR AUTHORIZED SERVICE PERSONNEL.
Air Conditioner Service Manual
TABLE OF CONTENTS
LG Model Name ...............................................................................................................................................3
Safety Precautions..........................................................................................................................................4
Dimensions .....................................................................................................................................................8
Symbols used in this Manual......................................................................................................................8
Indoor Unit..................................................................................................................................................8
Outdoor Unit...............................................................................................................................................9
Product Specifications ................................................................................................................................11
Installation .....................................................................................................................................................12
Select the Best Location .........................................................................................................................12
Piping Length and Elevation.....................................................................................................................12
Preparing Work for Installation .................................................................................................................13
Fixing the Indoor Unit ...............................................................................................................................14
Drill a Hole in the wall...............................................................................................................................14
Flaring Work.............................................................................................................................................15
Connecting the Pipings ............................................................................................................................16
Connecting the Cables to the Indoor Unit ................................................................................................19
Connecting the Cables to the Outdoor Unit..............................................................................................20
Checking the Drainage.............................................................................................................................21
Forming the Piping ...................................................................................................................................21
Air Purging ...............................................................................................................................................22
Air Purging with Vacuum Pump................................................................................................................22
Front Panel Assembly ..............................................................................................................................24
Test Running ............................................................................................................................................25
Operation ......................................................................................................................................................26
Function of Controls .................................................................................................................................26
Display Function.......................................................................................................................................33
Self-diagnosis Function............................................................................................................................34
Remote Control Operations......................................................................................................................35
Disassembly ..................................................................................................................................................36
Indoor Unit................................................................................................................................................36
Schematic Diagram.......................................................................................................................................38
Electric control Device..............................................................................................................................38
Wiring Diagram.........................................................................................................................................39
Components Location ..............................................................................................................................40
Troubleshooting Guide .................................................................................................................................42
Refrigeration Cycle Diagram ....................................................................................................................42
2-way, 3-way Valve ...................................................................................................................................43
Cycle Parts...............................................................................................................................................48
Electronic Parts ........................................................................................................................................49
Exploded View ..............................................................................................................................................56
Indoor Unit...............................................................................................................................................56
Outdoor Unit............................................................................................................................................57
Replacement Parts List ................................................................................................................................59
Indoor ......................................................................................................................................................59
Outdoor ....................................................................................................................................................60
2 Room Air Conditioner
LG Model Name
2003
1
Code
2
-
3
Type
4
5
6
Code of Model
7
8
9
10
Meaning
1
Producing Center,
Refrigerant
A~Z
L: Chang-won R22
A: Chang-won R410A
C: Chang-won R407C
T: China
K: Turkey R22
E: Turkey R410A
H: Thailand
N: India
Z: Brazil
D: Indonesia
M: Mexico
V: Vietnam
S: Out Sourcing
2
Product Type
A~Z
S: Split Type Air Conditioner
3
Cooling/Heating/Inverter
A~Z
C: Cooling only
H: Heat pump
X: C/O + E/Heater
Z: H/P + E/Heater
4, 5
Capacity
0~9
Cooling/Heating Capacity
Ex. "09" → 9,000 Btu/h
6
Electric Range
1~9
A~Z
1: 115V/60Hz,
2: 220V/60Hz
3: 208-230V/60Hz
5: 200-220V/50Hz
6: 220-240V/50Hz
7: 110V, 50/60Hz
8: 380-415V/50Hz
9: 380-415V/60Hz
7
Chassis
A~Z
Name of Chassis of Unit
Ex. LSP → SP Chassis
8
Look
A~Z
Look,
Color (Artcool Model)
9
Function
A~Z
10
Serial No.
1~9
V: AC Inverter C/O
N: AC Inverter H/P
Q: DC Inverter C/O
W: DC Inverter H/P
A: 220V, 50Hz, 3Phase
B: 208~230V, 60Hz, 3Phase
C: 575V, 50Hz, 3Phase
D: 440~460, 60Hz, 3Phase
E: 265V, 60Hz
F: 200V, 50/60Hz
Basic
Basic+4Way
Plasma Filter
Plasma Filter+4 Way
Tele+LCD
Tele+LCD+Nano plasma+4Way
Nano Plasma F+(A/changeove)+A/clean+Low A
Nano Plasma F+(A/changeove)+A/clean+4way+Low A
Tele+LED+4way
Internet
Plasma F+4Way+Oxy generator
Nano Plasma F+(A/changeove)+A/clean
Nano Plasma F+(A/changeove)+A/clean+4way
Nano Plasma F+(A/changeove)+A/clean+PTC
Nano Plasma F+(A/changeove)+Autoclean+4way+PTC
Nano Plasma F+(A/changeove)+A/clean+4way+Low A+PTC
Negative ION+A/Clean
(Nano)Plasma+Negative ION+A/Clean
4way+(Nano)Plasma F+Negative ION+Healthy dehumidification+A/Clean
Nano Plasma F+4Way+(A/changeove)+A/clean+
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
Q
R
S
T
U
LG Model Development Serial No.
* ARTCOOL COLOR
R
Mirror
W
White
B
Blue
D
Wood
M
Metal
C
Cherry
Service Manual 3
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must
be followed.
■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
■ Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
■ Installation
Always perform grounding.
• Otherwise, it may cause electrical
shock.
Securely attach the electrical
part cover to the indoor unit
and the service panel to the
outdoor unit.
Don’t use a power cord, a plug
or a loose socket which is
damaged.
• Otherwise, it may cause a fire or
electrical shock.
Always install an air leakage
breaker and a dedicated
switching board.
• If the electrical part cover of the
• No installation may cause a fire and
indoor unit and the service panel of
electrical shock.
the outdoor unit are not attached
securely, it could result in a fire or
electric shock due to dust, water, etc.
For installation of the product,
always contact the service center or
a professional installation agency.
• Otherwise, it may cause a fire, electrical shock, explosion or injury.
Do not keep or use flammable
gases or combustibles near
the air conditioner.
• Otherwise, it may cause a fire or the
failure of product.
x
Wa Thinner
4 Room Air Conditioner
Safety Precautions
Ensure that an installation
frame of the outdoor unit is
not damaged due to use for a
long time.
• It may cause injury or an accident.
Do not disassemble or repair
the product randomly.
• It will cause a fire or electrical shock.
Do not install the product at a
place that ther is concern of
falling down.
• Otherwise, it may result in personal
injury.
■ Operation
Use caution when unpacking
and installing.
• Sharp edges may cause injury.
Do not modify or extend the
power cord randomly.
• Otherwise, it may cause a fire or
electrical shock.
Do not share the outlet with
other appliances.
• It will cause an electric shock or a
fire due to heat generation.
Take care so that the power
cord may not be pulled during
operation.
• Otherwise, it may cause a fire or
electrical shock.
Do not use the damaged
power cord.
• Otherwise, it may cause a fire or
electrical shock.
Unplug the unit if strange
sounds, smell, or smoke
comes from it.
• Otherwise, it may cause electrical
shock or a fire.
Service Manual 5
Safety Precautions
Keep the flames away.
• Otherwise, it may cause a fire.
Do not open the suction inlet
of the indoor/outdoor unit during operation.
• Otherwise, it may electrical shock
and failure.
Take the power plug out if necessary, holding the head of the plug
and do not touch it with wet hands.
• Otherwise, it may cause a fire or
electrical shock.
Do not allow water to run into
electrical parts.
• Otherwise, it may cause a fire and
electrical shock.
Never touch the metal parts of
the unit when removing the filter.
• Otherwise, it may cause the failure of • They are sharp and may cause
machine or electrical shock.
injury.
Do not step on the indoor/outdoor unit and do
not put anything on it.
• It may cause an injury through dropping of the unit or
falling down.
When the product is submerged into water,
always contact the service center.
• Otherwise, it may cause a fire or electrical shock.
6 Room Air Conditioner
Do not use the power cord
near the heating tools.
Do not place a heavy object on the power cord.
• Otherwise, it may cause a fire or electrical shock.
Take care so that children may not step on the
outdoor unit.
• Otherwise, children may be seriously injured due to
falling down.
Safety Precautions
■ Installation
Install the drain hose to
ensure that drain can be
securely done.
• Otherwise, it may cause water leakage.
Install the product so that the
noise or hot wind from the
outdoor unit may not cause
any damage to the neighbors.
Always inspect gas leakage
after the installation and repair
of product.
• Otherwise, it may cause dispute with
the neighbors.
• Otherwise, it may cause the failure of
product.
■ Operation
Keep level parallel in installing the product.
• Otherwise, it may cause vibration or water leakage.
Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent.
• The appearance of the air conditioner may deteriorate,
change color, or develop surface flaws.
Avoid excessive cooling and perform ventilation sometimes.
• Otherwise, it may do harm to your health.
When gas leaks, open the window for ventilation before operating the unit.
• Otherwise, it may cause explosion, and a fire.
x
Wa Thinner
Service Manual 7
Dimensions
Dimensions
Symbols used in this Manual
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that may cause harm to the
air conditioner.
NOTICE
This symbol indicates special notes.
Indoor Unit
Hanger Hole
W
D
H
Fix Hole
Pipe Hole
Model
INDOOR UNIT
Dimension
W
mm
570
H
mm
568
D
mm
137
8 Room Air Conditioner
Dimensions
Outdoor Unit
L2
D
L1
W
H
L3
L5
Gas side
(3-way valve)
L4
Liquid side
(2-way valve)
DIM
MODEL
unit
AS-H076PB/D/M/WL1
W
mm
575
H
mm
525
D
mm
260
L1
mm
301
L2
mm
73
L3
mm
392
L4
mm
35
L5
mm
100
Service Manual 9
Dimensions
L2
D
L1
W
H
L3
L5
Gas side
(3-way valve)
L4
Liquid side
(2-way valve)
DIM
MODEL
unit
AS-H096PB/D/M/WL1, AS-H126PB/D/M/WL1
W
mm
770
H
mm
540
D
mm
245
L1
mm
285
L2
mm
64
L3
mm
518
L4
mm
10
L5
mm
100
10 Room Air Conditioner
Product Specifications
Product Specifications
Table-1
Model Name
AS-H076PB/D/M/WL1 AS-H096PB/D/M/W/L1
Item
A-12AH series
Unit
7500
9200
12000
7700
9400
12200
l/h
1
1.2
1.5
Ø, V, Hz
1Ø, 220-240V, 50Hz
1Ø, 220-240V, 50Hz
1Ø, 220-240V, 50Hz
5.5
6.8
8.3
20
26
26
37
39
44
48
48
48
685
840
1099
705
860
1200
3
3.8
4.9
3.1
3.85
5.3
10.95
10.95
10.92
3.2
3.2
2.98
24
24
24
18
25.5
25.5
570 x 568 x 137
570 x 568 x 137
570 x 568 x 137
575 x 525 x 260
770 x 540 x 245
770 x 540 x 245
9
9
9
23
35
35
750(R410A)
870(R410A)
880(R410A)
O
O
O
L.C.D Wireless
L.C.D Wireless
L.C.D Wireless
1/4 (6.35)
1/4 (6.35)
1/4 (6.35)
3/8 (9.52)
3/8 (9.52)
1/2 (12.7)
Sleeping Operation
O
O
O
Drain Hose
O
O
O
3*1.0mm2 + 2*0.75mm2
3*1.0mm2 + 2*0.75mm2
3*1.0mm2 + 2*0.75mm2
3*1.0mm2
3*1.0mm2
3*1.0mm2
Cooling Capacity
Btu/h
Heating Capacity
Moisture Removal
Power Source
Indoor
Air Circulation
Outdoor
Indoor
Noise Level
Outdoor
Input
m3/min
Cooling
Heating
Running
Cooling
Current
Heating
E.E.R.
Cooling
C.O.P
Heating
dB (A)±3
W
A
Btu/hW
Indoor
Motor Output
Dimensions
(W x H x D)
Outdoor
W
Indoor
Outdoor
mm
Indoor
Net. Weight
Outdoor
Refrigerant
kg
g
Airflow Direction Control (Up & Down)
Remocon Type
Liquid
Service Valve
Gas
Connecting Cable(p*mm2)
Power Cord(p*mm2)
inch(mm)
Service Manual 11
Installation
Installation
Selection of the Best Location
Indoor unit
• Do not have any heat or steam near the unit.
• Select a place where there are no obstacles in
front of the unit.
• Make sure that condensation drainage can be conveniently routed away.
Do not install near a doorway.
• Ensure that the space around the left and right of
the unit is more than 50cm. The unit should be
installed as high on the wall as possible, allowing a
minimum of 10cm from ceiling.
• Use a stud finder to locate studs to prevent unnecessary damage to the wall.
More than 10cm
More
than 50cm
More than 60cm
More than 10cm
More than 10cm
More
than 60cm
More than 70cm
Piping Length and Elevation
Max. Additional
Standard Max.
Length Elevation Length Refrigerant
A (m)
(g/m)
(m)
B (m)
Pipe Size
Capacity
(Btu/h)
GAS
LIQUID
7k, 8k, 9k
3/8"
1/4"
7.5
7
15
20
12k, 18k~28k
1/2"
1/4"
7.5
7
15
20
Indoor unit
Outdoor unit
More
than 50cm
A
More than 2m
Indoor unit
A
B
B
Outdoor unit
CAUTION: Install the indoor unit on the wall
where the height from the floor is more than 2
meter.
Outdoor unit
Outdoor unit
• If an awning is built over the unit to prevent direct
sunlight or rain exposure, make sure that heat
radiation from the condenser is not restricted.
• Ensure that the space around the back and sides
is more than 10cm. The front of the unit should
have more than 70cm of space.
• Do not place animals and plants in the path of the
warm air.
• Take the air conditioner weight into account and
select a place where noise and vibration are minimum.
• Select a place so that the warm air and noise from
the air conditioner do not disturb neighbors.
12 Room Air Conditioner
Oil trap
A
Indoor unit
B
If the piping length is more than 5m
CAUTION:
• Capacity is based on standard length and maximum
allowance length is on the basis of reliability.
• Oil trap should be installed every 5~7 meters.
I
Installation
Preparing Work for Installation
Open front panel
1. Push the front panel backward and lift it up to remove the two screws.
2. As soon as you lift the both lower parts of panel front, you can hear the sound from panel front. At this moment
panel front is separated
3. After pulling down this panel a bit, separate connecting wire from the product.
Panel Front
Connector
Remove pipe cover and side cover
1. Remove two screws(for fixing pipe cover)
2. Pull up the side cover of desired connecting direction,
and then side cover is separated.
3. Pick the pipe hole of the side cover.
CAUTION: After removing the pipe
hole, cut the burr for safety.
Pipe hole
Side cover
NOTICE
When making pipe path through rear
wall, you don’t need to pick the pipe hole.
Drain hose junction
1. Remove the rubber stopple in the desired drain direction.
2. Insert drain hose into the handle of drain pan, and
join drain hose and connecting hose according to the
figure by.
Adhesive
Connecting
part
Drain
hose
Only the
desired direction
rubber cap
Service Manual 13
Installation
Fixing the Indoor Unit
1. Attach an Installation guide map on the
desired surface.
INSTALLATION GUIDE MAP
6. Look at suited horizon by horizontal
meter on the horizontal setting line, and
fix lightly the map by adhesive tape.
Horizontality
2. Make a hole with a diameter of 6mm and
depth of 30-35mm by piercing a screw
point.
IN
ST
AII
AT
IO
N
IN
ST
AL
LA
TIO
N
GU
ID
EM
AP
7. Drill the pierted part as a diameter of 50mm
for connecting piping. (In case of piercing
rear surface)
GU
ID
EM
AP
3. Drive the fore plastic anchors into drilled
points.
IN
ST
AL
LA
TIO
N
GU
ID
EM
AP
Plastic anchors
4. Hang the hole of product at the upper
screws, and remove the map. (Falling
attention)
INS
TAL
LAT
ION
GUID
EM
AP
8. First, Drive the two points of the upper
parts by screws. (Leave 10mm for hanging
the product)
mm
10
IN
ST
AL
LA
TIO
N
GU
9. Drive the lower parts after facing the hole
of product with plastic anchors, and fix
completely the upper screws.
Plastic anchors
Hanger hole
(Rear side of
the product)
5. Check the fixed product with light power.
10. In case of nothing wrong, connect the
pipe and the wire. (Refer to installation
manual)
Drill a Hole in the Wall
WALL
Outdoor
14 Room Air Conditioner
(0.2~0.3")
Indoor
5-7mm
• Drill the piping hole with a ø50mm hole core drill.
Drill the piping hole at either the right or the left with
the hole slightly slanted to the outdoor side.
Installation
Flaring Work
Main cause for gas leakage is due to defect in flaring work. Carry out correct flaring work in the following procedure.
Cutting the pipes and the cable.
1. Use the piping kit accessory or the pipes purchased
locally.
Copper
pipe
Slanted Uneven Rough
90°
2. Measure the distance between the indoor and the outdoor unit.
3. Cut the pipes a little longer than measured distance.
4. Cut the cable 1.5m longer than the pipe length.
Removing burrs
Pipe
1. Completely remove all burrs from the cut cross section of
pipe/tube.
Reamer
2. Put the end of the copper tube/pipe in a downward direction as you remove burrs in order to avoid dropping burrs
into the tubing.
Point down
Flare nut
Putting nut on
• Remove flare nuts attached to indoor and outdoor unit,
then put them on pipe/tube having completed burr
removal.
(not possible to put them on after flaring work)
Copper tube
Flaring work
2. Carry out flaring work with the flaring tool.
Outside diameter
mm
inch
Ø6.35
1/4
Ø9.52
3/8
Ø12.7
1/2
Ø15.88
5/8
Ø19.05
3/4
A
mm
0~0.5
0~0.5
0~0.5
0~1.0
1.0~1.3
Bar
Handle
"A"
1. Firmly hold copper pipe in a die in the dimension shown
in the table below.
Bar
Yoke
Cone
Copper pipe
Clamp handle
Red arrow mark
Service Manual 15
Installation
Check
Smooth all round
1. Compare the flared work with the figure by.
Inside is shiny without scratches
2. If a flared section is defective, cut it off and do flaring
work again.
= Improper flaring =
Inclined Surface Cracked Uneven
damaged
thickness
Even length
all round
Connecting the Pipings
Indoor
Preparing the indoor unit's piping and drain hose for installation through the wall.
Route the indoor tubing and the drain hose in the
direction of rear left or right
Drain hose
Tape the tubing, drain hose and the connecting
cable. Be sure that the drain hose is located at the
lowest side of the bundle. Locating at the upper
side can cause drain pan to overflow inside the unit.
Loop
Connecting
cable
Gas side piping
Liquid side piping
Drain hose
NOTICE
If the drain hose is routed inside the room, insulate the hose with an insulation
material* so that dripping from "sweating"(condensation) will not damage furniture
or floors.
*Foamed polyethylene or equivalent is recommended.
16 Room Air Conditioner
Installation
Connecting the pipings with the indoor unit
and drain hose with drain pipe
1. Align the center of the pipings and sufficiently tighten
the flare nut by hand.
Indoor unit tubing
Flare nut
Pipes
2. Tighten the flare nut with a wrench.
Outside diameter
mm
inch
Ø6.35
1/4
Ø9.52
3/8
Ø12.7
1/2
Ø15.88
5/8
Ø19.05
3/4
Torque
kg.m
1.8
4.2
5.5
6.6
6.6
Open-end wrench (fixed)
Flare nut
Connection pipe
Wrench
Indoor unit tubing
3. When extending the drain hose at the indoor unit,
install the drain pipe.
Drain hose
Indoor unit drain hose
Adhesive
Wrap the insulation material around the
connecting portion.
Vinyl tape (narrow)
Plastic bands Insulation material
1. Overlap the connection pipe insulation material and
the indoor unit pipe insulation material. Bind them
together with vinyl tape so that there may be no gap.
2. Wrap the area which accommodates the rear piping
housing section with vinyl tape.
Indoor
unit pipe
Connection
pipe
Vinyl tape
Wrap with vinyl tape
(wide)
Connecting cable
Pipe
3. Bundle the piping and drain hose together by wrapping them with vinyl tape over the range within which
they fit into the rear piping housing section.
Vinyl tape(narrow)
Wrap with vinyl tape
Pipe
Vinyl tape(wide)
Drain hose
Service Manual 17
Installation
Outdoor
Align the center of the pipings and sufficiently tighten
the flare nut by hand.
Finally, tighten the flare nut with torque wrench until the
wrench clicks.
• When tightening the flare nut with torque wrench,
ensure the direction for tightening follows the arrow on
the wrench.
Outside diameter
mm
inch
Ø6.35
1/4
Ø9.52
3/8
Ø12.7
1/2
Ø15.88
5/8
Ø19.05
3/4
18 Room Air Conditioner
Torque
kg.m
1.8
4.2
5.5
6.6
6.6
Outdoor unit
Gas side piping
(Bigger diameter)
Liquid side
piping
(Smaller
diameter)
Torque wrench
Installation
Connecting the Cables to the Indoor Unit.
• Connect the cables to the indoor unit by connecting the wires to the terminals on the control board
dividually according to the outdoor unit connection. (Ensure that the color of the wires of the outdoor unit and the
terminal No. are the same as those of the indoor unit.)
• Before connecting the cables to the terminal block, remove the cables in the holder of the control cover and
do it.
CAUTION:
• The above circuit diagram is subject to change without notice.
• The earth wire should be longer than the common wires.
• When installing, refer to the circuit diagram behind the panel front of the indoor unit.
• Connect the wires firmly so that they may not be pulled out easily.
• Connect the wires according to color codes, referring to the wiring diagram.
CAUTION: If a power plug is not
used, provide a circuit breaker
between power source and the unit
as shown by.
Main power source
Air
Conditioner
Circuit Breaker
Use a circuit breake
or time delay fuse.
CAUTION: The power cord connected to the "A" unit should be selected according to
the following specifications(Type "B" approved by HAR or SAA).
(mm2)
Grade
NORMAL CROSS
5k~9k 12k~14k
-SECTIONAL AREA
0.75
1.0
Unit(A)
Indoor
Indoor
18k
1.5
Indoor
24k~28k 30k, 32k 36k, 38k
2.5
2.5
5.5
Indoor Outdoor Outdoor
Cable Type(B) H05VV-F H05VV-F H05VV-F H05VV-F H05RN-F H05RN-F
The power connecting cable connecting the indoor and outdoor unit should be selected
according to the following specifications (Type "B" approved by HAR or SAA).
(mm2)
NORMAL
Grade
CROSS
5k~9K 12k~14k 18k
-SECTIONAL
0.75
1.0
1.5
AREA
24k~28k
2.5
Cable Type(B) H07RN-F H07RN-F H07RN-F H07RN-F
NORMAL
CROSS-SECTIONAL
AREA 0.75mm2
(mm2)
Grade
NORMAL CROSS
30k, 32k 36k, 38k
-SECTIONAL AREA
0.75
0.75
Cable Type(B) H07RN-F H07RN-F
Service Manual 19
Installation
Connecting the Cables to the Outdoor Unit
1. Remove the control cover from the unit by loosening the screw.
Connect the wires to the terminals on the control
board individually.
Outdoor Unit
Terminal block
2. Secure the cable onto the control board with the
cord clamp.
3. Refix the control cover to the original position
with the screw.
Over 5mm
Connecting cable
Connecting cable
4. Use a recognized circuit breaker "A"
between the power source and the unit.
A disconnecting device to adequately disconnect
all supply lines must be fitted.
Circuit
Breaker
(A)
Cover control
Grade
7K~18K
~26K
~30K
~38K
15
20
30
40
CAUTION: After the confirmation of the above conditions, prepare the wiring as
follows:
1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring,
be guided by the circuit diagram posted on the inside of control cover.
2) The screw which fasten the wiring in the casing of electrical fittings are liable to come loose from vibrations
to which the unit is subjected during the course of transportation. Check them and make sure that they are
all tightly fastened. (If they are loose, it could cause burn-out of the wires.)
3) Specification of power source.
4) Confirm that electrical capacity is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the
name plate.
6) Confirm that the cable thickness is as specified in the power source specification.
(Particularly note the relation between cable length and thickness. (Refer to page 19)
7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.
• Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal function of the overload.
9) The means for disconnection from a power supply shall be incorporated in the fixed wiring and have an air
gap contact separation of at least 3mm in each active(phase) conductors.
20 Room Air Conditioner
Installation
Checking the Drainage
Forming the Piping
1. Checking the drainage.
• Pour a glass of water on the evaporator.
• Ensure the water flows through the drain hose of
the indoor unit without any leakage and goes out
the drain exit.
1. Form the piping by wrapping the connecting
portion of the indoor unit with insulation material and secure it with two kinds of vinyl tapes.
• If you want to connect an additional drain hose,
the end of the drain outlet should be routed above
the ground. Secure the drain hose appropriately.
2. In cases where the outdoor unit is installed
below the indoor unit perform the following.
• Tape the piping, drain hose and connecting cable
from down to up.
• Secure the tapped piping along the exterior wall
using saddle or equivalent.
Seal small openings
around pipings with a
gum type sealer.
Taping
Drain
hose
Pipings
Connecting
cable
2. Drain piping
• The drain hose should point downward for easy
drain flow.
Downward slope
• Do not make drain piping like the following.
Accumulated
drain water
Air
Do not raise
Trap is required to prevent water
from entering into electrical parts.
3. In cases where the Outdoor unit is installed
above the Indoor unit perform the following.
• Tape the piping and connecting cable from down
to up.
• Secure the taped piping along the exterior wall.
Form a trap to prevent water entering the room.
• Fix the piping onto the wall by saddle or equivalent.
Seal a small opening
around the pipings
with gum type sealer.
Water
leakage
Water
leakage
Tip of drain hose
dipped in water
Water
leakage
Waving
Less than
50mm gap
Trap
Trap
Ditch
Service Manual 21
Installation
Air Purging
Air and moisture remaining in the refrigerant system
have undesirable effects as indicated below.
• Pressure in the system rises.
• Operating current rises.
• Cooling(or heating) efficiency drops.
• Moisture in the refrigerant circuit may freeze and
block capillary tubing.
• Water may lead to corrosion of parts in the refrigeration system.
Therefore, the refrigerant system must be leak tested and evacuated to remove any noncondensables
and moisture from the system.
Air Purging with Vacuum Pump
• Do a leak test of all joints of the tubing(both indoor
and outdoor) and both gas and liquid side service
valves.
Bubbles indicate a leak. Be sure to wipe off the
soap with a clean cloth.
• After the system is found to be free of leaks,
relieve the nitrogen pressure by loosening the
charge hose connector at the nitrogen cylinder.
When the system pressure is reduced to normal,
disconnect the hose from the cylinder.
Indoor unit
1. Preparation
• Check that each tube(both liquid and gas side
tubes) between the indoor and outdoor units have
been properly connected and all wiring for the test
run has been completed. Remove the service
valve caps from both the gas and the liquid side on
the outdoor unit. Note that both the liquid and the
gas side service valves on the outdoor unit are
kept closed at this stage.
2. Leak test
• Connect the manifold valve(with pressure gauges)
and dry nitrogen gas cylinder to this service port
with charge hoses.
Outdoor unit
Manifold valve
Pressure
gauge
CAUTION: Be sure to use a manifold valve
for air purging. If it is not available, use a stop
valve for this purpose. The "Hi" knob of the manifold
valve must always be kept close.
Lo
Hi
Charge hose
• Pressurize the system to no more than 150
P.S.I.G. with dry nitrogen gas and close the cylinder valve when the gauge reading reached 150
P.S.I.G. Next, test for leaks with liquid soap.
CAUTION: To avoid nitrogen entering the
refrigerant system in a liquid state, the top of
the cylinder must be higher than its bottom when you
pressurize the system. Usually, the cylinder is used
in a vertical standing position.
22 Room Air Conditioner
Nitrogen gas
cylinder(in vertical
standing position)
Installation
Soap water method
Gas side
(1) Remove the caps from the 2-way and 3-way
valves.
(2) Remove the service-port cap from the 3-way valve.
(3) To open the 2-way valve turn the valve stem counterclockwise approximately 90°, wait for about 2~3
sec, and close it.
(4) Apply a soap water or a liquid neutral detergent on
the indoor unit connection or outdoor unit connections by a soft brush to check for leakage of the
connecting points of the piping.
(5) If bubbles come out, the pipes have leakage.
3. Evacuation
• Connect the charge hose end described in the preceding steps to the vacuum pump to evacuate the
tubing and indoor unit.
Confirm the "Lo" knob of the manifold valve is
open. Then, run the vacuum pump.
The operation time for evacuation varies with tubing length and capacity of the pump. The following
table shows the time required for evacuation.
Liquid side
3-way valve
(Close)
2-way valve
(Open)
Cap
Hexagonal wrench
Indoor unit
Required time for evacuation when 30 gal/h vacuum pump is
used
If tubing length is less than 10m
(33 ft)
10 min. or more
Outdoor unit
if tubing length is longer than 10m
(33 ft)
15 min. or more
• When the desired vacuum is reached, close the
"Lo" knob of the manifold valve and stop the vacuum pump.
4. Finishing the job
• With a service valve wrench, turn the valve stem of
liquid side valve counter-clockwise to fully open
the valve.
• Turn the valve stem of gas side valve counterclockwise to fully open the valve.
• Loosen the charge hose connected to the gas side
service port slightly to release the pressure, then
remove the hose.
• Replace the flare nut and its bonnet on the gas
side service port and fasten the flare nut securely
with an adjustable wrench. This process is very
important to prevent leakage from the system.
• Replace the valve caps at both gas and liquid side
service valves and fasten them tight.
This completes air purging with a vacuum pump.
The air conditioner is now ready to test run.
Manifold valve
Pressure
gauge
Lo
Hi
Open
Close
Vacuum pump
Service Manual 23
Installation
Front Panel Assembly
1. First, Check the side cover assembly exactly,
and fix the power cord in the bottom groove of
cover side left.
2. Assemble connecting lead wire with controller,
fix the upper part of the front panel, and match
the lower part of the front panel.
Panel Front
Connector
3. Screw up the front panel, and suspend the hook
of the front panel in the groove.
24 Room Air Conditioner
Test Running
Intake temperature
1. Check that all tubing and wiring have been properly
connected.
2. Check that the gas and liquid side service valves are
fully open.
Discharge air
Prepare remote controller
1. Remove the battery cover
by pulling it according to the
arrow direction.
2. Insert new batteries making
sure that the (+) and (–) of
battery are installed correctly.
3. Reattach the cover by
pushing it back into position.
NOTICE
Discharge
temperature
4. For reference; the gas side pressure of optimum
condition is as below.(Cooling)
R-22
Outside ambient
TEMP.
35°C (95°F)
The pressure of the gas side
service valve.
4~5kg/cm2G(56.8~71.0 P.S.I.G.)
R-410A
35°C (95°F)
8.5~9.5kg/cm2G(120~135 P.S.I.G.)
Refrigerant
• Use 2 AAA(1.5volt) batteries. Do not use
rechargeable batteries.
• Remove the batteries from the remote
control if the system is not going to be
used for a long time.
Settlement of outdoor unit
• Anchor the outdoor unit with a bolt and
nut(ø10mm) tightly and horizontally on a concrete
or rigid mount.
• When installing on the wall, roof or rooftop, anchor
the mounting base securely with a nail or wire
assuming the influence of wind and earthquake.
• In the case when the vibration of the unit is conveyed to the hose, secure the unit with an antivibration bushing.
NOTICE
If the actual pressure is higher than shown,
the system is most likely over-charged, and
charge should be removed. If the actual pressure are lower than shown, the system is
most likely undercharged, and charge should
be added.
The air conditioner is now ready for use.
PUMP DOWN
This is performed when the unit is to be relocated
or the refrigerant circuit is serviced.
Pump Down means collecting all refrigerant in the
outdoor unit without loss in refrigerant gas.
CAUTION:
Be sure to perform Pump Down procedure with the
unit cooling mode.
Bolt
Tubing connection
Evaluation of the performance
Operate unit for 15~20 minutes, then check the system
refrigerant charge:
1. Measure the pressure of the gas side service valve.
2. Measure the temperature of the intake and discharge
of air.
3. Ensure the difference between the intake temperature and the discharge is more than 8°C(46°F)
(Cooling) or (Heating).
Pump Down Procedure
1. Connect a low-pressure gauge manifold hose to
the charge port on the gas side service valve.
2. Open the gas side service valve halfway and purge
the air from the manifold hose using the refrigerant
gas.
3. Close the liquid side service valve(all the way in).
4. Turn on the unit's operating switch and start the
cooling operation.
5. When the low-pressure gauge reading becomes 1
to 0.5kg/cm2 G(14.2 to 7.1 P.S.I.G.), fully close the
gas side valve stem and then quickly turn off the
unit. At that time, Pump Down has been completed
and all refrigerant gas will have been collected in
the outdoor unit.
Service Manual 25
Operation
Operation
Function of Controls
DISPLAY
1) C/O Model (high quality LCD remote controller supplied)
Operation Indicator
• On while in appliance operation, off while in appliance pause
Timer Indicator
• On while in timer mode (on/off) and in sleep timer mode, off when timer mode is completed or canceled.
Comp. Running Indicator
• While in appliance operation, on while in outdoor unit compressor running, off while in compressor off
Plasma Indicator
• On while in plasma mode, off while plasma mode is canceled.
Auto restart Indicator
• On while auto restart mode, off while auto restart mode is canceled.
Auto restart
• In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate
procedures automatically to the previous operating conditions.
If your want to use this operation, press the Auto Restart Button.
Power(Forced Operation)
• Operation starts, when this button is pressed and stops when you press the button again.
2) H/P Model (high quality LCD remote controller supplied)
Operation Indicator
• On while in appliance operation, off while in appliance pause
Timer Indicator
• On while in timer mode (on/off) and in sleep timer mode, off when timer mode is completed or canceled
Defrost Indicator
• Off except when hot start during heating mode operation or while in defrost control.
Plasma Indicator
• On while in plasma mode, off while plasma mode is canceled.
Auto restart Indicator
• On while auto restart mode, off while auto restart mode is canceled.
Auto restart
• In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate
procedures automatically to the previous operating conditions.
If your want to use this operation, press the Auto Restart Button.
Power(Forced Operation)
• Operation starts, when this button is pressed and stops when you press the button again.
■ Cooling Mode Operation
• When the intake air temperature reaches 0.5°C below the setting temp, the compressor and the outdoor fan stop.
• When it reaches 0.5°C above the setting temp, they start to operate again.
Compressor ON Temp=> Setting Temp+0.5°C
Compressor OFF Temp => Setting Temp-0.5°C
• While in compressor running, operating with the airflow speed set by the remote controller. While in compressor
not running, operating with the low airflow speed regardless of the setting.
26 Room Air Conditioner
Operation
■ Healthy Dehumidification Mode
• When the dehumidification operation input by the remote controller is received, the intake air temperature is
detected and the setting temp is automatically set according to the intake air temperature.
26°C ≤ Intake Air Temp
=> 25°C
24°C ≤ Intake Air Temp < 26°C => Intake Air Temp-1°C
18°C ≤ Intake Air Temp < 24°C => Intake Air Temp-0.5°C
Intake Air Temp < 18°C
=> 18°C
• While in compressor off, the indoor fan repeats low airflow speed and pause.
• While the intake air temp is between compressor on temp. and compressor off temp., 10-min dehumidification
operation and 4-min compressor off repeat
Compressor ON Temp. => Setting Temp+0.5°C
Compressor OFF Temp. => Setting Temp-0.5°C
• In 10-min dehumidification operation, the indoor fan operates with the low airflow speed.
■ Heating Mode Operation
• When the intake air temp reaches +3°Cabove the setting temp, the compressor is turned off. When below the
setting temp, the compressor is turned on.
Compressor ON Temp. => Setting Temp.
Compressor OFF Temp. => Setting Temp.+3°C
• While in compressor on, the indoor fan is off when the indoor pipe temp. is below 26®¨C , when above 28°C , it
operates with the low or setting airflow speed (while in sleep mode, with the medium airflow speed).
• While in compressor off, the indoor fan is off when the indoor pipe temp is below 33°C , when above 35°C , it
operates with the low airflow speed.
• If overloaded while in heating mode operation, in order to prevent the compressor from OLP operation, the outdoor fan is turned on/off according to the indoor pipe temp.
• While in defrost control, both of the indoor and outdoor fans are turned off.
■ Defrost Control
• While in heating mode operation in order to protect the evaporator pipe of outdoor unit from freezing, reversed
to cooling cycle to defrost the evaporator pipe of the outdoor unit.
• Defrost control is available 30 minutes later since heating mode operation started, and it will not prolong over 6
minutes.
• Deicing starts only when the outdoor pipe temperature falls below -6°C after 30 minutes passed from starting of
heating operating and more than 10 minutes operation of compressor.
• Deicing ends after 6 minutes passed from starting of deice operation or when the outdoor pipe temperature rises
over 12°C even if before 6 minutes.
■ Fuzzy Operation (C/O Model)
• According to the temperature set by Fuzzy rule, when the intake air temp is 0.5°C or more below the setting
temp, the compressor is turned off. When 0.5°C or more above the setting temp, the compressor is turned on.
Compressor ON Temp => Setting Temp+0.5°C
Compressor OFF Temp => Setting Temp+0.5°C
• At the beginning of Fuzzy mode operation, the setting temperature is automatically selected according to the
intake air temp at that time.
Service Manual 27
Operation
26°C ≤ Intake Air Temp
=> 25°C
24°C ≤ Intake Air Temp<26°C => Intake Air Temp+1°C
22°C ≤ Intake Air Temp<24°C => Intake Air Temp+0.5°C
18°C ≤ Intake Air Temp<22°C => Intake Air Temp
Intake Air Temp<18°C
=> 18°C
• When the Fuzzy key (Temperature Control key) is input after the initial setting temperature is selected, the
Fuzzy key value and the intake air temperature at that time are compared to select the setting temperature
automatically according to the Fuzzy rule.
• While in Fuzzy operation, the airflow speed of the indoor fan is automatically selected according to the temperature
■ Fuzzy Operation (H/P Model)
• When any of operation mode is not selected like the moment of the power on or when 3 hrs has passed since
the operation off, the operation mode is selected.
• When determining the operation mode, the compressor, the outdoor fan, and the 4 way valve are off and only
the indoor fan is operated for 15 seconds. Then an operation mode is selected according to the intake air
temp at that moment as follows.
24°C ≤ Inatake Air Temp
=> Fuzzy Operation for Cooling
21°C ≤ Inatake Air Temp<24°C => Fuzzy Operation for Dehumidification
Inatake Air Temp<21°C
=> Fuzzy Operation for Heating
• If any of the operation modes among cooling / dehumidification / heating mode operations is carried out for 10
sec or longer before Fuzzy operation, the mode before Fuzzy operation is operated.
1) Fuzzy Operation for Cooling
• According to the setting temperature selected by Fuzzy rule, when the intake air temp is 0.5°C or more below
the setting temp, the compressor is turned off. When 0.5°C or more above the setting temp, the compressor is
turned on.
Compressor ON Temp => Setting Temp+0.5°C
Compressor OFF Temp => Setting Temp+0.5°C
• At the beginning of Fuzzy mode operation, the setting temperature is automatically selected according to the
intake air temp at that time.
26°C ≤ Intake Air Temp
=> 25°C
24°C ≤ Intake Air Temp<26°C => Intake Air Temp+1°C
22°C ≤ Intake Air Temp<24°C => Intake Air Temp+0.5°C
18°C ≤ Intake Air Temp<22°C => Intake Air Temp
Intake Air Temp < 18°C
=> 18°C
• When the Fuzzy key (Temperature Control key) is input after the initial setting temperature is selected, the
Fuzzy key value and the intake air temperature at that time are compared to select the setting temperature
automatically according to the Fuzzy rule.
• While in Fuzzy operation, the airflow speed of the indoor fan is automatically selected according to the temperature.
2) Fuzzy Operation for Dehumidification
• According to the setting temperature selected by Fuzzy rule, when the intake air temp is 0.5°C or more below
the setting temp, the compressor is turned off. When 0.5°C or more above the setting temp, the compressor is
turned on.
Compressor ON Temp => Setting Temp+0.5°C
Compressor OFF Temp => Setting Temp+0.5°C
28 Room Air Conditioner
Operation
• At the beginning of Fuzzy mode operation, the setting temperature is automatically selected according to the
intake air temp at that time.
26°C ≤ Intake Air Temp
=> 25°C
24°C ≤ Intake Air Temp<26°C => Intake Air Temp+1°C
22°C ≤ Intake Air Temp<24°C => Intake Air Temp+0.5°C
18°C ≤ Intake Air Temp<22°C => Intake Air Temp
Intake Air Temp < 18°C
=> 18°C
• When the Fuzzy key (Temperature Control key) is input after the initial setting temperature is selected, the
Fuzzy key value and the intake air temperature at that time are compared to select the setting temperature
automatically according to the Fuzzy rule.
• While in Fuzzy operation, the airflow speed of the indoor fan repeats the low airflow speed or pause as in dehumidification operation.
3) Fuzzy Operation for Heating
• According to the setting temperature selected by Fuzzy rule, when the intake air temp is 3°C or more above the
setting temp, the compressor is turned off. When below the setting temp, the compressor is turned on.
Compressor ON Temp => Setting Temp
Compressor OFF Temp => Setting Temp + 3°C
• At the beginning of Fuzzy mode operation, the setting temperature is automatically selected according to the
intake air temp at that time.
20°C ≤ Intake Air Temp => Intake Air Temp + 0.5°C
Intake Air Temp < 20°C => 20°C
• When the Fuzzy key (Temperature Control key) is input after the initial setting temperature is selected, the
Fuzzy key value and the intake air temperature at that time are compared to select the setting temperature
automatically according to the Fuzzy rule.
• While in Fuzzy operation, the airflow speed of the indoor fan is set to the high or the medium according to the
intake air temperature and the setting temperature.
■ Airflow Speed Selection
• The airflow speed of the indoor fan is set to high, medium, low, or chaos by the input of the airflow speed selection key on the remote controller.
■ On-Timer Operation
• When the set time is reached after the time is input by the remote controller, the appliance starts to operate.
• The timer LED is on when the on-timer is input. It is off when the time set by the timer is reached.
• If the appliance is operating at the time set by the timer, the operation continues.
■ Off-Timer Operation
• When the set time is reached after the time is input by the remote controller, the appliance stops operating.
• The timer LED is on when the off-timer is input. It is off when the time set by the timer is reached.
• If the appliance is on pause at the time set by the timer, the pause continues.
Service Manual 29
Operation
■ Off-Timer <=> On-Timer Operation
• When the set time is reached after the on/off time is input by the remote controller, the on/off-timer operation is
carried out according to the set time.
■ Sleep Timer Operation
• When the sleep time is reached after <1,2,3,4,5,6,7,0(cancel) hr> is input by the remote controller while in
appliance operation, the operation of the appliance stops.
• While the appliance is on pause, the sleep timer mode cannot be input.
• While in cooling mode operation, 30 min later since the start of the sleep timer, the setting temperature
increases by 1°C After another 30 min elapse, it increases by 1°C again.
• When the sleep timer mode is input while in cooling cycle mode, the airflow speed of the indoor fan is set to
the low.
• When the sleep timer mode is input while in heating cycle mode, the airflow speed of the indoor fan is set to
the medium.
■ Chaos Swing Mode
• By the Chaos Swing key input, the vane automatically operates with the Chaos Swing or they are fixed to the
desired direction.
■ Chaos Natural Wind Mode
• When the Chaos Natural Wind mode is selected and then operated, the high, medium, or low speed of the airflow mode is operated for 2~15 sec randomly by the Chaos Simulation.”
■ Jet Cool Mode Operation (C/O Model)
• If the Jet Cool key is input at any operation mode while in appliance operation, the Jet Cool mode operates.
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the priority.
• During the JET COOL function at any moment, the A/C starts to blow the cool air with side louvers closed at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C.
■ Jet Cool Mode Operation (H/P Model)
• While in heating mode or Fuzzy operation, the Jet Cool key cannot be input. When it is input while in the other
mode operation (cooling, dehumidification, ventilation), the Jet Cool mode is operated.”
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the priority.
• During the JET HEAT function at any moment, the A/C starts to blow the hot air with side louvers closed at
extremely high speed for 60 minutes setting the room temp. automatically to 30°C.
■ Auto Restarting Operation
• When the power is restored after a sudden power failure while in appliance operation, the mode before the
power failure is kept on the memory and the appliance automatically operates in the mode on the memory.
• Operation Mode that is kept on the memory
- State of Operation ON/OFF
30 Room Air Conditioner
Operation
- Operation Mode/Setting Temp/Selected Airflow Speed
- Sleep Timer Mode/Remaining Time of Sleep Timer (unit of hour)
■ Forced Operation
• Operation procedures when the remote control can't be used.
• The operation will be started if the power button is pressed.
• If you want to stop operation, re-press the button.
Cooling Model
Operating mode
Indoor Fan Speed
Setting Temperature
Cooling
High
22°C
Heat pump Model
Room Temp. ≥ 24°C 21°C ≤ Room Temp. < 24°C Room Temp. < 21°C
Cooling
Healthy Dehumidification
Heating
High
High
High
22°C
23°C
24°C
• While in forced operation, the key input by the remote control has no effect and the buzzer sounds 10 times to
indicate the forced operation.
■ Test operation
• During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room temperature and resets in 18±1 minutes.
• During test operation, if remote controller signal is received, the unit operates as remote controller sets.
If you want to use this operation, open the front panel upward and Press the power button let it be pressed for
about 3 seconds.
• If you want to stop the operation, re-press the button.
■ Protection of the evaporator pipe from frosting
• If the indoor pipe temp is below 0°C in 7 min. after the compressor operates without any pause while in cooling
cycle operation mode, the compressor and the outdoor fan are turned off in order to protect the indoor evaporator pipe from frosting.
• When the indoor pipe temp is 7°C or higher after 3 min. pause of the compressor, the compressor and the outdoor fan is turned on according to the condition of the room temperature.
■ Buzzer Sounding Operation
• When the appliance-operation key is input by the remote control, the short "beep-beep-" sounds.
• When the appliance-pause key is input by the remote control, the long "beep—" sounds.
• When a key is input by the remote control while the slide switch on the main unit of the appliance is on the
forced operation position, the error sound "beep-beep-beep-beep-beep-" is made 10 times to indicate that the
remote control signal cannot be received.
Service Manual 31
Operation
■ Air Cleaner Operation
• When an air cleaner function is selected during Air Conditioner operation
- Plasma air cleaner function will be operated while in any operation mode with selecting the function.
- The function is to be stopped while it is operating with selecting the function.
• When an air cleaner function is selected during operation off
- The function will be only operated.
• When inlet grille of air conditioner is opened during plasma operation, High Voltage Generator(H.V.B) is to be
stopped. When inlet grille of air conditioner is closed during plasma operation, High Voltage Generator(H.V.B)
will be operated again.
32 Room Air Conditioner
Operation
Display Function
1. Heating Model
Operation Indicator
• Cooling, Soft Dry, Fan, Heating
Sleep Timer Indicator
• Sleep Mode
Timer Indicator
• Timer Mode
Defrost Indicator
2. Cooling Model
Operation Indicator
• Cooling, Soft Dry, Fan
Sleep Timer Indicator
• Sleep Mode
Timer Indicator
• Timer Mode
Outdoor Unit Operation
• Hot-start, Defrost
PLASMA Indicator
• PLASMA Mode
PLASMA Indicator
• PLASMA Mode
Service Manual 33
Operation
Self-diagnosis Function
Error
Code
Error Display LED
(Indoor body operation LED)
(once)
1
3sec
34 Room Air Conditioner
3sec
3sec
Error contents
• Indoor room temperature
thermistor open/short
• Indoor pipe temperature
thermistor open/short.
SVC check point
• Indoor Thermistor
assembly check
Operation
Remote Control Operations
The controls will look like the following.
Controls
Signal transmitter
5
1
6
3
4
2
7
11
8
13
10
CANCEL
ON
OFF
9
12
SET
AUTO CLEAN
17
14
15
16
Flip-up door
(opened)
Operation Mode
Cooling Operation
Auto Operation or Auto Changeover
Healthy Dehumidification Operation
Heating Operation
• Cooling Model(
), Heat Pump Model(
)
1. START/STOP BUTTON
Operation starts when this button is pressed and
stops when the button is pressed again.
2. OPERATION MODE SELECTION BUTTON
Used to select the operation mode.
3. ROOM TEMPERATURE SETTING BUTTONS
Used to select the room temperature.
4. INDOOR FAN SPEED SELECTOR
Used to select fan speed in four steps
low, medium, high and CHAOS.
5. JET COOL/HEATING(OPTIONAL)
Used to start or stop the speed
cooling. (Speed cooling/heating operates at super
high fan speed in cooling/heating mode.)
6. CHAOS SWING BUTTON
Used to stop or start louver movement and set the
desired up/down airflow direction.
7. ON/OFF TIMER BUTTONS
Used to set the time of starting and stopping operation.
8. TIME SETTING BUTTONS
Used to adjust the time.
9. TIMER SET/CANCEL BUTTON
Used to set the timer when the desired time is
obtained and to cancel the Timer operation.
10. SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
11. AIR CIRCULATION BUTTON
Used to circulate the room air without cooling or
heating.
12. ROOM TEMPERATURE CHECKING BUTTON
Used to check the room temperature.
13. NANO PLASMA(OPTIONAL)
Used to start or stop the plasma-purification
function.
14. HORIZONTAL AIRFLOW DIRECTION CONTROL
BUTTON
(OPTIONAL)
Used to set the desired horizontal airflow direction.
15. RESET BUTTON
Used prior to resetting time or after replacing batteries.
16. 2nd F Button
Used prior to using modes printed in blue at the
bottom of buttons.
17. AUTO CLEAN(OPTIONAL)
Used to set Auto Clean mode.
Service Manual 35
Disassembly
Disassembly
Indoor Unit
WARNING: Disconnect the unit from
power supply before making any
checks. Be sure the power switch is set
to "OFF"
1. To remove the Grille from the Chassis.
- Pull the grille bottom, the remove 2 securing screws.
- Lift the both lower parts of panel front.
- After pull down this panel a bit, separate connecting
wire with product.
Panel Front
Connector
2. To remove the Control Box.
- Before removing the control box, be sure to
disconnect the wires from PWB.
- Pull the cover control out from the control box
and disconnect other wires.
- Remove securing screws.
- Pull the control box out from the chassis carefully.
Step Motor Connectors
Sensor Connector
4Way/Fan Connector
Comp Connector
Power Connector
Power Connector
Comp Connector
36 Room Air Conditioner
Motor
Connector
Disassembly
3. To remove the Evaporator.
- Remove 4 screws securing the evaporator.
- Pull the evaporator out from the chassis carefully.
4. Before removing the Turbo Fan.
- Remove the securing screws from the chassis.
- Pull the pipe cover, top cover and the air guide.
Air Guide
Top Cover
Pipe Cover
5. To remove the Motor.
- Remove the securing bolt from the motor shaft.
- Pull the fan out from the motor shaft.
- Remove 4 screws securing motor mount from the
chassis and lift up the motor mount and the bracket.
Bracket
Turbo Fan
Bolt
Motor Mount
Service Manual 37
LED3
PLASMA
LED2
PLASMA
LED1
PLASMA
Vout
GND
Vcc
RECEIVER
10
Digit2
LED1
ON/OFF
LED4
DEFROST
LED3
TIMER
LED2
SLEEP
DISPLAY
STEPPING MOTOR
흡입구 1
d
g
2
2
e
f
1
1
8(c)
7(e)
6(d)
9(b)
1(g)
3(a)
FAN
MOTOR
14
14
14
15
RD
BK
YL
BL
WH
1
2
3
4
3
4
7
6
7
6
5
2
2
5
1
1
3
1
3
2
2
2
3
1
1
3
15
14
15
14
13
12
12
12
12
13
11
11
11
11
13
10
10
10
10
13
8
9
8
9
8
7
6
5
4
3
2
1
CN-D2 8PIN
CN-D2 7PIN
CN-MOTOR1(WH)
CN-12V(WH)
CN-CON(WH)
CN-D3
9
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
RD OR YL PK BL
9
7
6
5
4
3
2
1
1
2
3
3
1
2
CN-SW(BL)
C11D
473
630V
(TM)
5
6
7
8
9
5
6
7
8
9
10
11
10
11
ZD02D
6.8V
DC 311V
13
10K
C10D
100UF
25V
R12D
13
12
11
11
12
10
10
CN-D1
9
9
8
7
7
8
5
6
4
5
4
6
3
2
3
2
1
1
2
3
4
2
3
4
CN-D2
1
1
CN-D1
R11D
5.1K
C12D
103
4.7K 1%
R10D
L3
12uH(DIP)
13
13
12
11
11
12
10
CN-D1(WH)
Q04C
Q03C
Q02C
12V
5V
D05D
1N4148
2
1
2
1
2
1
3
4
IC06D
PC-17K1
3
4
3
4
IC05D
PC-17K1
C02L
220
10V
5V
R12H
10K
KRA223S
Q01C
IC07D
R08D
PC-17K1
4.7K 1%
KRA101M
Q02G
Q01G
KRA101M
+15V
12V
HVB PIN1
HVB
HVB PIN2
receiver
CN-D2(WH)
11
10
9
8
10
11
10
9
8
7
7
5
5
6
4
4
6
3
2
1
9
7
8
5
6
2
3
4
1
CN-D1(WH)
3
2
1
9
7
8
5
6
2
3
4
1
R01P
20K
Hall Sensor1
5V
PWM
OJ01H
OJ02H
R28H 20K
ON/OFF
5V
C13H
103
50V
R27H 20K
R11H
1K
5V
KRC107S
Q08C
Q07C
Q06C
Q05C
R07G 510
R06G 510
R05G 510
R04G 510
R03G 510
R03P
20K
R02P
20K
+15V
on/off
5V
8
7
6
5
12V
C03D
220uF
35V
2
3
12
13
14
15
16
11
DC LOW
VOLTAGE GND
ZD01D
BZX55C11
R07D
1K
+
3
4
5
0IMCRNE002M
uPD780023AGC
CY4
4
6
6
7
C09D
104
SMPS
DC HIGH
VOLTAGE GND
C04D
470uF
25V
2
3
8
9
Vss1
INTO
X2
X1
AVret
AVdd
RESET
D 5
S 2
BP 1
5
5
6
12V
IC01D
TNY266P
D07D
1N4937
R09D 1K
+
INT
8
8
C01D
150uF
450V
10
10
1/2W
R04D
560K
NTC
SCK-084
R02E 20
11
O2
12
12
1/4W
3216
C08D
104
50V
1/4W
3216
R01D
300K
300K
R02D
C07D
220uF
25V
(DIP) BD01D
D3SBA60
D01D
1N4007
4WAY
+
R21H~R26H
12.1K 1%
5V
R01A
1K
OSC01B
CST-8.00MTW
11
E3 1K
E2 1K
R26H
R25H
R24H
R23H
R22H
R21H
5V
5V
R01E
1K
R01B
1M
12V
COMP OUT
9
9
INT
5V
OR1H
F1
PWM
DC311V
5V
7
7
OR3H OR2H
Low
F2
6
33
36
35
34
38
37
42
41
40
39
44
43
47
46
45
48
OR4H
Med
H/S2
C14D
103
H/S1
4
4
RY-FAN
4-WAY
IC04M
ULN2004AFW
INT1
OR5H
Hi
EN 4
R14D
110K
ON
GND OFF
1
3
R13D 1K
2
PWM
OR6H
S-Hi
R14D 1K
1
C01M
103
D03D
UG2D
CN-ACDC1
CN-ACDC2
IC02D
PC-17K1
R13D
1K
1/4W
+
C12H
103
50V
D02D
UG2D
C02D
470uF
35V
103 (DIP)
CY3
3
1
R06D
39
L2
12uH(DIP)
R05D
1K
1/2W
2
1
11 10
17 18 1920 21 22 23 24 25 26 27 28 29 30 31. 32
Vdd0
VssO
C11HR30H
103 10K
50V
5V
1
16 15 14 13 12
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
R01P R02P
20K
20K
L1
12uH(DIP)
+
1
4
5
6
7
8
9
10
IC01D BP
R29H
10K
R16D
10K
1
2
3
4
R08D 1K
LED scan
PLASMA
digit 2
103
C02M
c
5V
e
digit 1
2
1
16
15
d
b
a
g
f
3
7
6
5
4
3
2
IC01M
8 ULN2004AFW
14
11
12
13
R02G 510
9
10
12V
14
15
R01G 510
RY-COMP
RY-O2
13
7
6
5
4
10
11
12
HVB
1
C04D
104
50V
CY1~2
471M
2
1
C02N
0.22uF
275VAC
(DIP)
3
4
IC03D
PC-17K1
+ C03L
220uF
10V
L3
3
INT
2
5V
C01N
0.22UF
275VAC
(DIP)
IC01A
KIA7036P
KSC7536
receiver
N/F01N
15mH/1.5A
3.6V
1
R02L
1K
5V
R02A 20K
C01L
680pF
50V
R01L
5.1K
S78DL05L,1W(DIP)
C01A
103
50V
D04D
1N4148
7805
IC04D
E1
330
BZ01E
PKM13EPP-4002
9
250V/T3.15A
(DIP)
FUSE
1/2W
R01D
1M
RY-COMP
G4A-1A
RY-4WAY
RY-FAN
INT
5V
CN-HVB(BL)
3
1
2
3
1
4
3
2
5
1
1
2
3
4
5
1
CN-O2
1
2
3
1
CN-POW1
1
CN-POW2
4
5
4
3
2
4
CN-TH1(WH)
HVB PIN2
RY-O2
12V
CN-LR2(WH)
HVB PIN1
C10D
103
50V
R04D
47K
5V
R02H
12.1K
1%
OPTION
R05H
10K
R04H
6.2K
1%
C02A
220
10V
5V
ZNR01N
TVR10561
+
R05D
56K
KTC3198Y
Q01D
10K
R03D
11
6
14
13
12
8
3
4
5
IC03M
ULN2004AFW
CN-LR1(WH)
5
1
1
1
2
3
4
5
1
1
2
3
4
1
2
3
1
4
3
2
5
1
4
3
2
PIPE-TH
ROOM-TH
HVB ASSY
STEP MOTOR
L/R2
STEP MOTOR
L/R1
AC220-240V
50/60Hz
T/BLOCK
BL PK YL OR RD
IN DOOR
C04L
0.01
25V
5
Digit1
c
b
a
4(f)
CN-MAIN
TEST
KEY
4
3
2
1
4
3
2
1
5
CN-D5
8
9
5 4 3 2
5 4 3 2
BL PK YL OR RD
AVdd1
5
12V
CN-UD(BL)
RXD
IC02M
ULN2004AFW
AVss
38 Room Air Conditioner
5V
BL PK YL OR RD
TXD
SUB PCB ASM
STEPPING MOTOR
상하 토출구
Schematic Diagram
Schematic Diagram
Electric Control Device
• Heat Pump Model
Schematic Diagram
Wiring Diagram
Indoor Unit
Outdoor Unit
AS-H076PB/D/M/WL1
AS-H096PB/D/M/WL1
AS-H126PB/D/M/WL1
Service Manual 39
Schematic Diagram
Components Location
MAIN P.W.B ASSEMBLY (AC PART)
• HEAT PUMP MODEL
PWB : 6870A90161D
R14D
R10D
R11D
Q01G
C12D
C11D
SMPS
ZD02D
R05D
L3
C03D
D05D CN-ACDC1
R08D
R09D
D06D
Q02G
R16D
C10D
C02D
CY5
D02D
D03D
L1
IC07D IC08D
IC05D IC06D
C09D
R13D ZD01D
IC02D
R07D R06D
IC01D
NF01N
PWB ASM : 6871A10121
MAIN P.W.B ASSEMBLY (DC PART)
• TOP VIEW
40 Room Air Conditioner
1
R01D
CN-COM
RY-O2
C02N
C01N
ZNR01N
RY-FAN
CN-O2
3
CN-MOTOR1
1
CY3
-
GND
4
R03D
R02D
FUSE
R04D
BD01D
~
~
CN-POW1
RY-4WAY
CN-MOTOR2
CY4
C14D
CN-OUT
IC03D
D04D
250V-T3.15A
250V-T3.0A
125V-T3.15A
CN-POW2
4
RY-COMP
2(N)
CY1
3
CN-COMP
NTC
C01D
D07D
R15D
1(L)
D01D
+
R12D
CN-GND1
2
CY
T/BLOCK
• BOTTOM VIEW
C04D
L2
Schematic Diagram
DISPLAY ASSEMBLY
– 6871A20462
TOP VIEW
BOTTOM VIEW
SUB P.W.B ASSEMBLY
CN-D4
PWB ASM:6871A20363
1
CN-D3
PWB:6870A90126B
CN-D2
C02V
1
1
1
CN-CON(WH)
CN-12V(WH)
CN-D5
C01V
CN-D1
1
1
1
1
CN-SW(BL)
CN-D7
1
1
CN-D6
1
CN-D8
1
Service Manual 41
Troubleshooting Guide
Troubleshooting Guide
Refrigeration Cycle Diagram
(1) Cooling Only Models
INDOOR UNIT
OUTDOOR UNIT
LIQUID SIDE
CAPILLARY TUBE
HEAT
EXCHANGE
(CONDENSER)
HEAT
EXCHANGE
(EVAPORATOR)
GAS SIDE
COMPRESSOR
(2) Cooling & Heating Models
INDOOR UNIT
OUTDOOR UNIT
LIQUID SIDE
CHECK VALVE
(Heating Model only)
3-WAY VALVE
CAPILLARY TUBE
HEAT
EXCHANGE
(EVAPORATOR)
HEAT
EXCHANGE
(CONDENSER)
GAS SIDE
3-WAY VALVE
REVERSING
VALVE
(Heating Model Only)
ACCUMU
LATOR
COMPRESSOR
42 Room Air Conditioner
COOLING
HEATING
Troubleshooting Guide
2-way, 3-way Valve
2-way Valve (Liquid Side)
Hexagonal wrench (4mm)
Flare nut
3-way Valve (Gas Side)
Valve cap
Open position
Flare nut
Closed position
Open position
Closed position
To
piping
connection
To
piping
connection
To outdoor unit
Works
Shipping
1.
Air purging
(Installation)
Operation
Pin
Service Service
port cap port
To outdoor unit
Shaft position
Shaft position
Service port
Closed
(with valve cap)
Closed
(with valve cap)
Closed
(with cap)
Open
(counter-clockwise)
Closed
(clockwise)
Open
(push-pin or with
vacumm pump)
Open
(with valve cap)
Open
(with valve cap)
Closed
(with cap)
Closed
(clockwise)
Open
Open
(counter-clockwise) (connected manifold
gauge)
2.
Pumping down
(Transfering)
Open
Open
3.
Evacuation
(Servicing)
Open
(with charging
cylinder)
Open
Open
4.
Gas charging
(Servicing)
Open
(with charging
cylinder)
5.
Pressure check
(Servicing)
Open
Open
Open
(with charging cylinder)
6.
Gas releasing
(Servicing)
Open
Open
Open
(with charging cylinder)
Service Manual 43
Troubleshooting Guide
Pumping Down
Liquid side
Indoor unit
2-Way
valve
Open
Outdoor unit
Gas side
Closed
3-Way
valve
Lo
CLOSE
CLOSE
Purge the air
• Procedure
(1) Confirm that both the 2-way and 3-way valves
are set to the open position.
– Remove the valve stem caps and confirm that
the valve stems are in the raised position.
– Be sure to use a hexagonal wrench to operate
the valve stems.
(2) Operate the unit for 10 to 15 minutes.
(3) Stop operation and wait for 3 minutes, then
connect the charge set to the service port of
the 3-way valve.
– Connect the charge hose with the push pin to
the service port.
(4) Air purging of the charge hose.
– Open the low-pressure valve on the charge set
slightly to air purge from the charge hose.
(5) Set the 2-way valve to the closed position.
44 Room Air Conditioner
(6) Operate the air conditioner at the cooling
cycle and stop it when the gauge indicates
1kg/cm2g.
(7) Immediately set the 3-way valve to the closed
position.
– Do this quickly so that the gauge ends up indicating 3 to 5kg/cm2g.
(8) Disconnect the charge set, and mount the 2way and 3-way valve’s stem nuts and the service port nut.
– Use torque wrench to tighten the service port
nut to a torque of 1.8 kg.m.
– Be sure to check for gas leakage.
Troubleshooting Guide
Balance Refrigerant of the 3-way Valve
(Gas leakage)
Liquid side
Indoor unit
Outdoor unit
3-Way
valve
Open
Gas side
3-Way
valve
Open
Lo
OPEN
CLOSE
• Procedure
(1) Confirm that both the 2-way and 3-way valves
are set to the back seat.
(2) Connect the charge set to the 3-way valve’s
port.
– Leave the valve on the charge set closed.
– Connect the charge hose to the service port.
(3) Open the valve (Lo side) on the charge set and
discharge the refrigerant until the gauge indicates 0 kg/cm2G.
– If there is no air in the refrigerant cycle (the
pressure when the air conditioner is not running
is higher than 1 kg/cm2G), discharge the refrigerant until the gauge indicates 0.5 to 1
kg/cm2G. if this is the case, it will not be necessary to apply a evacuatin.
– Discharge the refrigerant gradually; if it is discharged too suddenly, the refrigeration oil will
also be discharged.
Service Manual 45
Troubleshooting Guide
Evacuation
(All amount of refrigerant leaked)
Liquid side
Indoor unit
Outdoor unit
3-Way
valve
Open
Gas side
3-Way
valve
Open
Vacuum pump
Lo
OPEN
CLOSE
• Procedure
(1) Connect the vacuum pump to the center hose
of charge set center hose
(2) Evacuation for approximately one hour.
– Confirm that the gauge needle has moved
toward -76 cmHg (vacuum of 4 mmHg or less).
(3) Close the valve (Lo side) on the charge set,
turn off the vacuum pump, and confirm that
the gauge needle does not move (approximately 5 minutes after turning off the vacuum
pump).
(4) Disconnect the charge hose from the vacuum
pump.
– Vacuum pump oil.
If the vacuum pump oil becomes dirty or
depleted, replenish as needed.
46 Room Air Conditioner
Troubleshooting Guide
Gas Charging
(After Evacuation)
Liquid side
Indoor unit
3-Way
valve
Open
Outdoor unit
Gas side
Open
3-Way
valve
Check valve
Charging
cylinder
Lo
(1)
OPEN
CLOSE
• Procedure
\
(1) Connect the charge hose to the charging
cylinder.
– Connect the charge hose which you dis-connected from the vacuum pump to the valve at
the bottom of the cylinder.
– If you are using a gas cylinder, also use a
scale and reverse the cylinder so that the system can be charged with liquid.
(2) Purge the air from the charge hose.
– Open the valve at the bottom of the cylinder
and press the check valve on the charge set to
purge the air. (Be careful of the liquid refrigerant). The procedure is the same if using a gas
cylinder.
(3) Open the valve (Lo side on the charge set and
charge the system with liquid refrigerant.
– If the system can not be charged with the specified amount of refrigerant, it can be charged
with a little at a time (approximately 150g each
time) while operating the air conditioner in the
cooling cycle; however, one time is not sufficient, wait approximately 1 minute and then
repeat the procedure (pumping down-pin).
This is different from previous procedures.
Because you are charging with liquid refrigerant
from the gas side, absolutely do not attempt to
charge with larger amounts of liquid refrigerant
while operating the air conditioner.
(4) Immediately disconnect the charge hose from
the 3-way valve’s service port.
– Stopping partway will allow the gas to be discharged.
– If the system has been charged with liquid
refrigerant while operating the air conditioner
turn off the air conditioner before disconnecting
the hose.
(5) Mount the valve stem nuts and the service
port nut.
– Use torque wrench to tighten the service port
nut to a torque of 1.8 kg.m.
– Be sure to check for gas leakage.
Service Manual 47
Troubleshooting Guide
Cycle Parts
Trouble analysis
1. Check temperature difference between intake and discharge air and operating current.
Temp. Difference
Operating Current
Temp. difference : approx. 0°C
Current
: less than 80% of
rated current
• All amount of refrigerant leaked
out. Check refrigeration cycle.
Temp. difference : approx. 8°C
Current
: less than 80% of
rated current
• Refrigerant leakege
Clog of refrigeration cycle
Defective compressor
Temp. difference : less than 8°C
Current
: over the reated
current
• Excessive amount of refrigerant
Temp. difference : over 8°C
• Normal
NOTICE
Temperature difference between intake and discharge air depends on room air humidity. When the room air
humidity is relativery higher, temperature difference is smaller. When the room air humidity is relatively lower temperature difference is larger.
2. Check temperature and pressure of refrigeration cycle.
Suction pressure
(Compared with
the normal value)
Temperature
(Compared with
the normal valve)
Cause of Trouble
High
Defective compressor
Defective 4-way reverse valve
Current is low.
Excessive amount of
refrigerant
High pressure does not quickly
rise at the beginning of
operation.
Insufficient amount of
refrigerant (Leakage)
Clogging
Current is low.
Higher
Normal
Lower
Higher
Description
Current is low.
NOTICE
1. The suction pressure is usually 4.5~6.0 kg/cm2G(Cooling) at normal condition.
2. The temperature can be measured by attaching the thermometer to the low pressure tubing and wrap it with
putty.
48 Room Air Conditioner
Troubleshooting Guide
Electronic Parts
Product does not operate at all.
(* Refer to Electronic Control Device drawing and Schematic diagram.)
Turn off Main Power
(After 10 seconds)
Turn on Main Power
Does "beeping" sound is made from the Indoor Unit?
YES
NO
Primarily, the operating condition of Micom is OK.
Check the voltage of power(About AC 220V, 60Hz)
(About AC 220/240V, 50Hz)
• Main power's voltage
• Voltage applied to the unit
• Connecting method of Indoor/Outdoor connecting
cable
• Check PWB Assembly
- Fuse
- Pattern damage
- Varistor(ZNR01N)
Check each load(Indoor/Outdoor Fan Motor,
Compressor, Stepping Motor) and contacting
condition of related connector
Check the connection housing for contacting
• Connector related to CN-POWER1, 2
• Connector related to CN-MOTOR
• Connector contacting of Outdoor Fan/Compressor
• Display PWB Assembly Check
Main PCB Board Operation Check
Content
Items
Remedy
• SMPS Transformer
(Indoor unit)
- Input Voltage
- Output Voltage
- About AC220V/240V±10% - Check the power voltage • Replace Trans
- About DC12V
• IC04D(7805) Output
• DC +5V
• Replace IC04D
• Voltage of Micom No. 36,
(DC +4.5V over) and Soldering condition.
• Replace faulty parts
• IC01A(Reset IC)
OSC01B(8MHz)
Service Manual 49
Troubleshooting Guide
The product does not operate with the remote controller.
Turn on Main Power
While the compressor has been stopped, the compressor does not
operate owing to the delaying function for 3 minutes after stopped.
When the compressor stopped Indoor Fan is driven by a low speed.
At this point the wind speed is not controlled by the remote controller.
(When operated in the Sleeping Mode, the wind speed is set to the
low speed by force.)
Cause by the remote control
When the mark(
battery.
) is displayed in LCD screen, replace
Check the connecting circuit between the remote controller
MICOM (No. 30 ) - R17(2Ω) - IR LED - TR - R16(2.2KΩ).
Caused by other parts except the remote control
Check the contact of CN-D1, 2 connector.
Check Display PWB Assembly
- Voltage between CN-D2
-
: DC +5V
Check point
• Check the connecting circuit between PIN R02L(1K) - C01L(680PF) - MICOM PIN 43
• Check Receiver Assembly
50 Room Air Conditioner
Troubleshooting Guide
Compressor/Outdoor Fan are unable to drive.
Turn on Main Power
Operate "Cooling Mode( )" by setting the desired temperature of the
remote controller is less than one of the indoor temperature by 1°C at least.
When in Air Circulation Mode, Compressor/Outdoor Fan is stopped.
Check the sensor for indoor temperature is attached as close as to be
effected by the temperature of Heat Exchanger(EVA).
When the sensor circuit for indoor temperature and connector are in bad
connection or are not engaged, Compressor/Outdoor Fan is stopped.
• Check R02H(12.1k), R04H(6.2k), Micom Pin 26, 27
• Check the indoor temperature sensor is disconnected or not(About 10kΩ / at 25°C).
Check Relay(RY - COMP) for driving compressor.
• When the power(About AC220V/240V) is applied to the connecting wire
terminal support transferred to compressor, PWB Assembly is normal.
• Check the circuit related to the relay.
Check point
Between Micom(No.
63) and GND
Between IC02M(No. 14)
and GND
COMP ON
COMP OFF
DC5V
DC0V
Below DC 1V
(app)
About DC12V
Turn off Main Power
• Check the electrical wiring diagram of outdoor side.
• Check the abnormal condition for the component of
Compressor/Outdoor Fan Motor.
• Check the "open" or "short" of conmecting wires between indoor and
outdoor.
Service Manual 51
Troubleshooting Guide
When Indoor Fan does not operate.
Turn off Main power
Check the connection of CN-MOTOR1, 2
Check the Fan Motor
Check the Fuse(AC250V/3.15A)
- Check PWM signal from Micom Pin 50
- Check On/Off signal from micom pin14.
- Check Voltage of CN-Motor 1, 2
(pin ~ is about 15V)
Turn ON Main Power
Fan can't operate for dehumidifying mode.
- Change operation for cooling mode.
52 Room Air Conditioner
Troubleshooting Guide
When Louvers do not operate.
• Confirm that the Louver is normally geared with the shaft of Stepping
Motor.
• If the regular torque is detected when rotating the Louver with hands
Normal
• Check the connecting condition of CN-UD, LR1, LR2 Connector.
• Check the soldering condition(on PWB) of CN-UD LR1, LR2 Connector.
Check the operating circuit of the Louvers.
• Confirm that there is DC +12V between pin of CN-UD and GND.
• Confirm that there is a soldering short at following terminals.
- Between 45 , 46 , 47 , 48 , 54 , 55 , 56 , 57 , 59 , 60 , 61 , 62 of MICOM
- Between
of IC02M
- Between ,
of IC03M
- Between , , , , , , ,
of IC04M
- Between , , ,
of CN-UD/LR1/LR2
If there are no problems after above checks
• Confirm the assembly conditions that are catching and interfering parts
in the rotation radial of the Louvers.
Service Manual 53
Troubleshooting Guide
When Heating does not operate
Turn ON Main Power
Operate “Heating Mode( )” by setting the desired temperature of the
remote control is higher than one of the indoor temperature by 2°C at
least.
In heating Mode, the indoor fan operates in case the pipe temperature
is higher than 28°C.
Check the connector of intake and pipe sensor(thermistors)
• Check the related circuit of RY-4WAY
• Check the indoor room temperature is disconnected or not (about
10KΩ/at 25°C).
• Check the indoor pipe temperature is disconnected or not (about
5KΩ/at 25°C).
Check the DC voltage on the PWB ASSEMBLY
• The details of check are as followings
• Comp Relay.
• Outdoor fan Relay
Check point
Comp ON
Comp OFF
Check point
Fan ON
Fan OFF
Between Micom
(NO.63) and GND
DC 5V
DC 0V
Between Micom
(NO.53) and GND
DC 5V
DC 0V
Between IC02M
Below DC 1V
(NO.14) and GND
About DC
12V
• 4 way Relay
Check point
4 way ON
4 way OFF
Between Micom
(NO.51) and GND
DC 5V
DC 0V
Between IC03M
(No.9) and GND
Below DC1V
About 12V
54 Room Air Conditioner
Between IC03M
Below DC 1V About DC 12V
(NO.11) and GND
Troubleshooting Guide
Turn off Main Power
• Check the electrical wiring diagram of outdoor side.
• Check the abnormal condition for the component of
Compressor/Outdoor Fan Motor, 4 way.
• Check the "open" or "short" of connecting wires between indoor and
outdoor.
Service Manual 55
56 Room Air Conditioner
135314
135312
268717
159830
152302
268712
267110
264110
249951
146811
359012
144710-1
268714-2
268714-1
146811
144710-2
146811
135500-3
349600
346810
135311-1
147581
330870
354210
135311-3
146811
135500-2
352380
135500-1
147581
263230
35211B
131410
352150
352116
352115
135515
146811
147581
135311-2
Exploded View
Exploded View
Indoor Unit
Exploded View
Outdoor Unit (AS-H076PB/D/M/WL1)
437210
437212
554031
435301
435511
546810
552102-2
559010
649950
552201
552111
552102-1
W0CZZ
552116
552202
567502
561410
554160
447910
550140
552203-1
430410
552203-2
Service Manual 57
Exploded View
Outdoor Unit (AS-H096PB/D/M/WL1, A-12AH..
437210
437212
554031
435301
435511
546810
552102
559010
649950
552201
552111
552116
W0CZZ
552202
567502
561410
554160
447910
550140
552203-1
430410
552203-2
58 Room Air Conditioner
Replacement Parts List
Replacement Parts List
Indoor Unit
LOCATION
No.
PART No.
DESCRIPTION
AS-H076PB/D/M/WL1 AS-H096PB/D/M/WL1
A-12AH series
REMARKS
131410
CHASSIS ASSEMBLY
3141A20004N
3141A20004D
3141A20004N
R
135303
GRILLE,INLET
3530A20077F
3530A20077F
3530A20077F
R
135311-1 GRILLE ASSEMBLY,DISCHARGE(INDOOR)
3531A20069G
3531A20069G
3531A20069G
R
135311-2 GRILLE ASSEMBLY,DISCHARGE(INDOOR)
3531A20069H
3531A20069H
3531A20069H
R
135311-3 GRILLE ASSEMBLY,DISCHARGE(INDOOR)
3531A20069J
3531A20069J
3531A20069J
R
135312
GRILLE ASSEMBLY,FRONT(INDOOR)
3531A20213E
3531A20213E
3531A20213E
R
135314
GRILLE ASSEMBLY,INLET
3531A20212E
3531A20212E
3531A20212E
R
135500-1 COVER
3550A20123A
3550A20123A
3550A20123A
R
135500-2 COVER
*
*
3550A20124A
R
135500-3 COVER
3550A20060A
3550A20060A
3550A20060A
R
135515
COVER ASSEMBLY,TOP(INDOOR)
3551A20031B
3551A20031B
3551A20031B
R
146811
MOTOR ASSEMBLY,STEP
4681A20055A
4681A20055A
4681A20055A
R
147581
LOUVER,HORIZONTAL
4758A20014B
4758A20014B
4758A20014B
R
152302
FILTER(MECH),A/C
5230A20032A
5230A20032A
5230A20032A
R
159830
AIR CLEANER ASSEMBLY
5983A20007F
5983A20007F
5983A20007F
R
249951
CONTROL BOX ASSEMBLY,INDOOR
4995A20372Q
4995A20372E
4995A20372A
R
263230
THERMISTOR ASSEMBLY
6323A20004N
6323A20004N
6323A20004N
R
264110
POWER CORD ASSEMBLY
6411A20014S
6411A20014S
6411A20014S
R
267110
REMOTE CONTROLLER ASSEMBLY
6711A20073Z
6711A20073Z
6711A20073Z
R
268712
PWB(PCB) ASSEMBLY,DISPLAY
6871A20462A
6871A20462A
6871A20462A
R
268714-1 PWB(PCB) ASSEMBLY,MAIN
6871A10121A
6871A10121A
6871A10121A
R
268714-2 PWB(PCB) ASSEMBLY,MAIN(DC)
6871A20439J
6871A20439D
6871A20439C
R
268717
PWB(PCB) ASSEMBLY,SUB
6871A20363D
6871A20363D
6871A20363D
R
330870
DRAIN PAN ASSEMBLY
3087A30004A
3087A30004A
3087A30004A
R
346810
MOTOR ASSEMBLY,INDOOR
4681A20091A
4681A20091A
4681A20091A
R
352115
TUBE ASSEMBLY,EVAPORATOR IN
*
*
5211A20302B
R
352116
TUBE ASSEMBLY,EVAPORATOR OUT
*
*
5211A20301B
R
35211B
TUBE ASSY,TUBING
5211AR7066F
5211AR7066F
5211AR7066D
R
352150
HOSE ASSEMBLY,DRAIN
5251AR1222R
5251AR1222R
5251AR1222R
R
352380
AIR GUIDE
5238A20020A
5238A20020A
5238A20020A
R
354210
EVAPORATOR ASSEMBLY,FIRST
5421A20072A
5421A20072A
5421A20072A
R
359012
FAN,TURBO
5900A00003A
5900A00003A
5900A00003A
R
NOTE) *Please ensure GCSC since these parts may be changed depending upon the buyer's request.
(GCSC WEBSITE http://biz@LGservice.com)
Service Manual 59
Replacement Parts List
Outdoor Unit
LOCATION
No.
DESCRIPTION
430410
BASE ASSY,OUTDOOR
435301
GRILLE,DISCHARGE
435511
PART No.
AS-H076PB/D/M/WL1 AS-H096PB/D/M/WL1
A-12AH series
REMARKS
3041A20016A
3041A20008K
3041A20008K
R
*
3530A20006B
3530A20006B
R
COVER ASSEMBLY,CONTROL(OUTDOOR)
3551A30023Q
3551A30023E
3551A30023E
R
437210
PANEL ASSEMBLY,FRONT(OUTDOOR)
3720A10171A
3721A20027B
3721A20027B
R
437212
PANEL ASSY,REAR(OUTDOOR)
3720A10172A
3721A20026B
3721A20026A
R
447910
BARRIER ASSEMBLY,OUTDOOR
4790A10025B
4791A30002A
4791A30002A
R
546810
MOTOR ASSEMBLY,OUTDOOR
4681A20121A
4681A20004S
4681A20004S
R
550140
ISOLATOR,COMP
4H00982E
*
4H00982E
R
552111
TUBE ASSEMBLY,CAPILLARY
5211A21121B
5211A30331Q
5211A20117J
R
552116
TUBE ASSEMBLY,REVERSING
5211A20188U
5211A20160E
5211A20140X
R
552201
VALVE,CHECK
5220AR7182A
5220AR7182A
5220AR7182A
R
552202
VALVE,REVERSING
5220AR3228D
5220AR3228B
5220AR3228D
R
552203-1 VALVE,SERVICE
2H02479P
2H02479H
2H02479H
R
552203-2 VALVE,SERVICE
5220A20001B
5220A20001B
5220A20006B
R
554031
CONDENSER ASSEMBLY,BENT
5403A20045M
5403A20019F
5403A20019V
R
554160
COMPRESSOR SET
2520UGDP2CA
2520UGAP2GA
2520UGHP2AA
R
559010
FAN ASSEMBLY,PROPELLER
5900AR1266A
5901A10004A
5901A10004A
R
561410
COIL ASSEMBLY,REVERSING VALVE
6141A20017A
3A02028Y
6141AR3733R
R
649950
CONTROL BOX ASSEMBLY,OUTDOOR
4995A10032B
4995A20083B
4995A20083Y
R
W0CZZ
CAPACITOR,DRAWING
6120AR2194H
6120AR2194N
2H01451T
R
NOTE) *Please ensure GCSC since these parts may be changed depending upon the buyer's request.
(GCSC WEBSITE http://biz.LGservice.com)
60 Room Air Conditioner
Memo
Service Manual 61
Memo
62 Room Air Conditioner
P/No.: 3828A20135S
February, 2004
Printed in Korea
Download PDF

advertising