ENGLISH OWNER'S MANUAL DVD Player Please read this manual carefully before operating your set and retain it for future reference. MODEL DVT589H P/NO : MFL63266716 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 2 Safety Precaution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction has been adhered to. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus. 2 CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. This device is equipped with a portable battery or accumulator. Safe way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessived heat such as sunshine, fire or the like. Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC and 2009/125/EC. European representative : LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel : +31–(0)36–547–8888) DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 3 Contents About the Safety Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Types of Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Hooking up the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Adjust the Disc playback settings . . . . . . . . . . . . . . . . . . . . . .9-10 Adjust the DVB-T or DAB settings . . . . . . . . . . . . . . . . . . . .10-12 Using the digital EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Displaying Disc Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15 Playing a DivX movie file . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Listening to Music Disc or files . . . . . . . . . . . . . . . . . . . . . .16-17 Viewing photo files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 USB Direct Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Using a USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Types of Playable Discs Type Logo DVD-VIDEO: Discs such as movies that can be purchased or rented DVD-R: Video mode and finalized only DVD-RW: VR mode, Video mode and finalized only DVD+R: Video mode only DVD+RW: Video mode only Audio CD: Music CDs or CD-R/CD-RW in music CD format that can be purchased This unit plays DVD±R/RW and CD-R/RW that contains audio titles, DivX, MP3, WMA and/or JPEG files. Some DVD±RW/DVD±R or CD-RW/CD-R cannot be played on this unit due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. Symbol Display “ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that disc. Regional Codes This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”. • Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play. • If you try to play a DVD with a different regional code from your player, the message “Check Regional Code” appears on the TV screen. Copyrights It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs picture noise will appear. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. 3 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 4 Hooking up the unit Hooking up the unit - more you can do Antenna connection A SCART connection Connect the Terrestrial TV antenna (A) to the ANTENNA IN jack on the unit. If you want to use an indoor antenna, use one with a signal amplifier rated at 5V, 100mA and set [Antenna Feed 5V] to [ON] in the setup menu (See page 11). Connect the TO TV jack on the unit and your TV using the SCART cable. For SCART connections, resolution must be set to 576i(480i) by pressing RESOLUTION button. Caution : You must set the [TV Output Select] option to [RGB] on the setup menu to use this connection. (See page 9) Antenna connection to your TV Connect one end of the RF cable (R) to ANTENNA OUT jack on the unit and other end to ANTENNA IN jack on your TV. Passes the signal from the ANTENNA IN jack to your TV/monitor. Audio and Video Connection The unit Audio/Video jacks are color coded (yellow for video, red for right audio and white for left audio). If your TV has only one input for audio (mono), connect it to the left (white) audio jack on the unit. Antenna (Digital) TV B Component Video Connections Connect the COMPONENT / PROGRESSIVE SCAN OUTPUT jacks on the unit to the corresponding input jacks on your TV using a YPbPr cable. • You will still need to connect the left and right audio cables to the TV, or digital audio cable to your stereo. Caution : You must set the [TV Output Select] option to [YPbPr] on the setup menu to use this connection. (See page 9) Resolution Setting • You can change the resolution for component video output. Press RESOLUTION repeatedly to select the desired resolution - 576i(480i), 576p(480p), 720p, 1080i, 1080p. • For 720p, 1080p and 1080i resolution on the component video output, only non-copy protected discs can be played back. If the disc is copy protected,it will be displayed at the 576p(480p) resolution. • Depending on your TV, some of the resolution settings may result in the picture disappearing or an abnormal picture appearing. In this case, press RESOLUTION repeatedly until the picture re-appears. C Digital Audio Output Connection Connect one of the unit’s DIGITAL AUDIO OUTPUT (COAXIAL) jack to the corresponding jack on your amplifier. • If the audio format of the digital output does not match the capabilities of your amplifier, the amplifier will produce a strong, distorted sound or no sound at all. • To see the audio format of the current disc in the on-screen display, press AUDIO. • This unit does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this unit to a DTS compatible amplifier via one of this unit’s digital audio outputs. Rear of this unit C 4 B A DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 5 HDMI Connection About HDMI Connect the HDMI OUTPUT jack (H) on the unit to the HDMI input jack on an HDMI compatible TV using an HDMI cable (Version 1.2). HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD Players, Set-Top Boxes, and other AV devices. HDMI was developed to provide the technologies of HDCP (High-bandwidth Digital Content Protection). HDCP is used to protect digital content transmitted and received. HDMI has the capability to support standard, enhanced or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs. TV H Rear of this unit Resolution Setting You can change the resolution for HDMI output. Press RESOLUTION repeatedly to select the desired resolution - 576i(480i), 576p(480p), 720p, 1080i, 1080p. The resolution may not be selected depending on the connection or TV. Note for 1080p resolution The unit is able to provide a 1080p HD image to most 1080p-capable TVs in the market today. However, there are some 1080p TVs available from certain companies that are limited in the types of 1080p images that can be accepted. Specifically, 1080p-capable TVs that don’t accept images in 60Hz can’t display an image from this unit. Notes on HDMI connection • If your TV is not capable of handling 96 kHz sampling frequency, set the [Sampling Freq.] option to [48 kHz] on the setup menu (See page 9). • If your TV is not equipped with Dolby Digital and MPEG decoder, set the [Dolby Digital] and [MPEG] options to [PCM] on the setup menu (See page 9). • Depending on your TV, some of the resolution settings may result in the picture disappearing or an abnormal picture appearing. In this case, press RESOLUTION repeatedly until the picture re-appears. • Changing the resolution when the unit is connected with HDMI connector may result in malfunctions. To solve the problem, turn off the unit and then turn it on again. • When you connect a HDMI or DVI compatible device, make sure of the following: - Try switching off the HDMI/DVI device and this unit. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this unit. - The connected device’s video input is set correctly for this unit. - The connected device is compatible with 720X576i(480i), 720X576p(480p), 1280X720p, 1920X1080i or 1920X1080p video input. - The 1080p, 720p and 576p(480p) resolutions are the progressive scan applied resolution. • Not all HDCP-compatible DVI devices will work with this unit. - The picture will not be displayed properly with non-HDCP device. 5 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 6 General about digital broadcast Picture and sound Digital TV is a transmission technology that replaces the traditional analogue technique. This means that several TV channels, radio channels and other digital services can be transmitted on the same space as just one channel took up before. As a consumer you get access to many more channels and services than before at the same time as they are received with perfect picture and audio quality. Coverage Before buying this product it is anticipated that you have made sure that there are digital transmissions covering your region. Antenna / Signal source Depending on the reception your unit may be connected to a simple indoor antenna or to an existing outdoor antenna system. If you live in a flat you should make sure that the digital terrestrial signals are distributed to your wall antenna outlet. If you have your own antenna system you must make sure that it is equipped with antennas, filter and/or amplifier that can handle those frequencies that the digital channels are transmitted on. Cable-TV Please observe that this unit is not designed for the reception of regular digital cable-TV signals (QAM-signal). Despite this, operators of smaller cable networks may have chosen to distribute the digital terrestrial signals (COFDM-signal) in the network. In this case this unit may well be used. Check with your landlord if you are insecure about what type of TV-signal that is provided in the wall antenna outlet. 6 DV589H-E.BFRALLK_6716_ENG 1/26/10 Remote control 7:45 PM a c d a d POWER (1) : Switches the unit ON or OFF. OPEN/CLOSE (Z) : Opens and closes the disc tray. INDEX ( ) / ZOOM : Moves to Index screen or page 100 in the teletext mode. Enlarges video image in disc mode. TV Control Buttons : You can control the sound level, input source, selects TV’s channel and power switch of your TV. Numerical buttons : Selects numbered items in a menu. SETUP : Accesses or exits the setup menu. TEXT ( ) : Switches between teletext mode and normal TV viewing. EPG : Displays the EPG menu. b Page 7 b SCAN (m / M) : Search backward or forward. SKIP (. / >) : Go to next or previous chapter/track/file. PAUSE/STEP (X) : Pauses playback temporarily/press repeatedly for frame-by-frame playback. PLAY (N) : Starts playback. STOP (x) : Stops playback. c MIX ( ) / TITLE : Displays the teletext pages superimposed on the TV picture. Accesses the disc’s title menu in disc mode, if available. Color buttons : Use when tuned to a teletext program of a digital broadcast. The function of each button will be described on-screen, and changes depending on the screen being displayed. REPEAT : Repeats a chapter, track, title or all. A-B : Repeats a section. PROGRAM : Enters the program edit mode. CLEAR : Removes a track/file number on the Program List. AUDIO ( ) : Selects an audio language or audio channel. MODE : Switches a operation mode (DVB-T, DAB or Disc). CH (+/-) : Scans up or down through memorized channels in DVB-T or DAB mode. DVD MENU : Accesses or exits the DVD menu. CH LIST : Displays the channel list. FAV. (+/-) : Tunes to your favorite channels. SUBTITLE ( b / B / v / V (left/right/up/down) : Used to navigate on-screen displays. Remove the battery cover on the rear of the Remote Control, and insert R03 (size AAA) battery with 3 and # matched correctly. ENTER ( ) : Confirms menu selection. DISPLAY : Accesses On-Screen Display. RETURN (O) : Press to move backwards in the menu or exit the menu. Changes to the USB mode. ) : Selects a subtitle language. ANGLE ( ) : Selects a DVD camera angle, if available. RESOLUTION : You can change the resolution depending on your TV. Put the Battery into the Remote Control 7 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 8 Main unit a b c a Disc Tray Insert a disc here. c Display window Shows the current status of the unit. d Remote sensor Point the remote control here. e 1 (Power) Turn the unit ON or OFF. 8 b f g f • N (Play) : Starts playback. • x (Stop) : Stops playback. MODE : Switches a operation mode (DVB-T, DAB or Disc). • . (Skip) : Returns to the beginning of current chapter/track/file or go to the previous chapter/track/file. CH - : Scans down through memorized channels. • > (Skip) : Go to next chapter/track/file. CH + : Scans up through memorized channels. g USB Port Connect a USB Flash Drive. b Z (Open / Close) Opens or closes the disc tray. a d e c d e f g h a AC Power Cord Connect to a power source. e VIDEO/AUDIO (R/L) OUTPUT Connect to a TV with video and audio inputs. b HDMI OUTPUT (Type A) Connect to a TV with HDMI inputs. (Interface for digital audio and video) f ANTENNA IN Connect the antenna to this terminal. c DIGITAL AUDIO OUTPUT (COAXIAL) Connect to a digital (coaxial) audio equipment. g ANTENNA OUT Passes the signal from the ANTENNA IN to your TV. d COMPONENT / PROGRESSIVE SCAN OUTPUT (Y PB PR) Connect to a TV with Y Pb Pr inputs. h SCART (TO TV) Connect to a TV with SCART jack. DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 9 Disc Audio/Subtitle/Menu – Select a language for the Disc Audio/Subtitle/ Menu. Selecting an operating mode You must select one of the operating modes before operating. Press MODE repeatedly to change the mode among DVB-T, DAB or Disc. Disc: You should select the Disc mode before using playback functions or disc setup setting. DVB-T: You should select the DVB-T mode before watching TV channel or using TV setup setting. DAB: You should select the DAB mode before listening to the radio or using radio setup setting. Adjust the Disc playback settings ON REMOTE 1 Select the disc mode: MODE 2 Display setup menu: SETUP 3 Select a desired option on the first level: vV 4 Move to second level: B 5 Select a desired option on the second level: vV 6 Move to third level: B 7 Change the setting: v V / ENTER [Original]: Refers to the original language in which the disc was recorded. [Other]: To select another language, press number buttons then ENTER to enter the corresponding 4-digit number according to the language code list (see page 20). If you make a mistake while entering number, press CLEAR to delete numbers then correct it. [Off] (for Disc Subtitle): Turn off Subtitle. Adjust the display settings TV Aspect – Select which screen aspect to use based on the shape of your TV screen. [4:3]: Select when a standard 4:3 TV is connected. [16:9]: Select when a 16:9 wide TV is connected. Display Mode – If you selected 4:3, you’ll need to define how you would like widescreen programs and films to be displayed on your TV screen. [Letterbox]: This displays a widescreen picture with black bands at the top and bottom of the screen. [Panscan]: This fills the entire 4:3 screen, cropping the picture as necessary. TV Output Select – Select an option according to the TV connection type. [RGB]: When your TV is connected with the SCART jack. [YPbPr]: When your TV is connected with the COMPONENT / PROGRESSIVE SCAN OUTPUT jacks on the unit. Adjust the audio settings Adjust the Disc playback settings - more you can do When you turn on for the first time (optional) The menu for a language selection will appear when you turn on the unit for the first time. You must select a language to use the unit. Use vV b B to select a language then press ENTER and the confirm menu will appear. Use b B to select [Enter] then press ENTER. Adjust the language settings Menu Language – Select a language for the Setup menu and on-screen display. Dolby Digital / DTS / MPEG – Selects the type of digital audio signal when using the DIGITAL AUDIO OUTPUT jack. [Bitstream]: Select this when you connect this unit’s DIGITAL AUDIO OUTPUT jack to an amplifier with a built-in Dolby Digital, DTS or MPEG decoder. [PCM] (for Dolby Digital / MPEG): Select this when you connect this unit’s DIGITAL AUDIO OUTPUT jack to an amplifier without a built-in Dolby Digital or MPEG decoder. [Off] (for DTS): Select this when you connect this unit’s DIGITAL AUDIO OUTPUT jack to an amplifier without a built-in DTS decoder. Sample Freq. (Frequency) – Selects the sampling frequency of the audio signal. [48 KHz]: The audio signals are always converted to 48 KHz. [96 KHz]: The audio signals are output in their original format. 9 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 10 DRC (Dynamic Range Control) – Make the sound clear when the volume is turned down (Dolby Digital only). Set to [On] for this effect. Adjust the DVB-T or DAB settings Vocal – Set to [On] only when a multi-channel karaoke DVD is playing. The karaoke channels on the disc mix into normal stereo sound. Adjust the lock settings You must set the [Area Code] option to use the lock options. Select [Area Code] option then press B. Enter a 4-digit password then press ENTER. Enter it again then press ENTER to verify. If you make a mistake while entering number, press CLEAR then correct it. If you forget your password you can reset it. First, remove the disc in the unit. Display setup menu then input the 6-digit number “210499”. The “P CLr” appear in the display window and the password is deleted. Rating – Select a rating level. The lower the level, the stricter the rating. Select [Unlock] to deactivate the rating. Password – Sets or changes the password for lock settings. [New]: Enter a new 4-digits password using the numerical buttons then press ENTER. Enter the password again to confirm. [Change]: Enter the new password twice after entering the current password. Area Code – Select a code for a geographic area as the playback rating level. This determines which area’s standards are used to rate DVDs controlled by the parental lock. (See page 20) Adjust the others settings B.L.E. (Black Level Expansion) – To select the black level of playback pictures, set your preference and monitor’s ability. DivX(R) VOD – DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified device that plays DivX video in HD resolutions. This DivX Certified ® device must be registered in order to play DivX Video-onDemand (VOD) content. First generate the DivX VOD registration code for your device and submit it during the registration process. [Important: DivX VOD content is protected by a DivX DRM (Digital Rights Management) system that restricts playback to registered DivX Certified devices. If you try to play DivX VOD content not authorized for your device, the message “Authorization Error” will be displayed and your content will not play.] Learn more at www.divx.com/vod. REC Bitrate – You can choose a bit rate for USB direct recording (128 Kbps, 160 Kbps, 192 Kbps, 256 Kbps or 320 Kbps). Higher bit rate gives the better sound quality but uses more space on the USB Flash Drive. For USB direct recording see page 18. 10 ON REMOTE 1 Select the DVB-T or DAB mode: MODE When the first time to turn on the unit, the “First time installation” menu will appear. Select [YES] and press ENTER for auto channel scanning. (see “ Auto Scan” below for details) 2 Display DVB-T or DAB setup menu: SETUP 3 Select a desired option on the first level: vV 4 Move to second level: B 5 Select a desired option on the second level: vV 6 Move to third level: B 7 Change the setting: v V / ENTER 8 Go back to the previous level: b Adjust the DVB-T or DAB settings - more you can do Adjust the programmed channels Auto Scan – This option automatically scans and sets the available channels. Currently selected mode (TV or Radio) will not be changed after the Auto channel scanning. [Country]: Use b B select a country where you operate this unit. [Auto Scan]: Use V b B to select [Yes] then press ENTER to start the channel scanning. TV Channel / Radio Channel – Displays the TV or Radio channel list. Use B to select the [Select] then press ENTER to display the channel list. You can also display the channel list pressing CH LIST while in DVB-T or DAB mode. While displaying channel list, press b B to display favorite channel list (See page 11). DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 11 Channel Class – This option allows you to set the favorite channel. Use v V select the a channel and press ENTER to set the favorite class on each channel (shows Fav icon on top of the screen). Aspect Ratio – Selects the aspects ratio of the connected TV. [4:3 PS]: Select this when connecting to a standard 4:3 screen TV and prefer the wide picture on the entire screen cuts off the portions that do not fit. [4:3 LB]: Select this when connecting to a standard 4:3 screen TV and prefer the wide picture with bands on the upper and lower portions of the screen. [16:9]: Select this when connecting to a wide-screen TV. Antenna Feed 5V – If you are using an indoor antenna, use one with a signal amplifier rated at DC 5 V, 100 mA and set this option to [ON]. [ON]: Power is supplied to the connected antenna. [OFF]: The unit does not supply power to the connected antenna. Adjust the time settings Channel Edit – This option allows you to edit the channels. [Add]: This option allows you to add a new channel. Use v V to select the channel and press ENTER to add the selected channel. [Select]: This option allows you to delete or move the preset channels. To move the location of the preset channel, use v V b B to highlight the channel you want to move on the [Move] column and press ENTER. Use v V to move the selected channel to the desired position and then press ENTER to complete move. To delete a preset channel, use v V b B to highlight the channel you want to delete on the [Delete] column and press ENTER. The x marked channel will not be displayed on the channel list. Press ENTER again to clear the x mark. Set the channel that broadcasts a clock signal and the clock will be set automatically. If the clock that has automatically set is different with your local clock, you can adjust time using [Time Offset] option (For example, when summer time is started in local area.). Press B to select [Time Offset] option. Press v V to select a value then press ENTER (Off, +/-30 min, +/-60 min, +/-90 min, +/-120 min). Select “Off” if the clock that has automatically set is identified with your local clock. Adjust the lock settings To access the Change Pin, Channel Lock, Parental Guidance options, you must enter the 4-digit password. If you have not yet entered a password you are prompted to do so. Enter a 4-digit password. Enter it again to verify. If you make a mistake while entering number, press CLEAR to delete numbers. If you forget your password, you can reset it. Display the SETUP menu. Input ‘210499’ and press ENTER. The password has now been cleared. Change Pin – Changes the password. Enter the new password twice after entering the current password. Channel Lock –You can lock certain unsuitable channels to prevent children from accessing them, use v V to select a channel you want to lock and then press ENTER to lock the channel. If you want to watch a locked channel. You should input the password. 11 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 12 Parental Guidance – Blocks TV programs that you or your family may not wish to watch, based on the rating scheme set. Select a rating then press ENTER. [3 Years] - [18 Years]: Rating [3 Years] has the most restrictions and rating [18 Years] is the least restrictive. [Blocking Off]: Permits all programs. Changing the Channel Use CH - / + on the remote control to change the channel in memory to select a channel directly. Changing the Channel with Channel list You can display channel list using the CH LIST button and switch into other channel on the channel list. Adjust the others settings OTA (Over the Air) – Your unit is able to keep the built-in digital tuner up to date with the latest software. The unit does it automatically at regular interval. While the unit is in updating, there may have a disruption in reception for a few hours. The reception should return to normal after the update is complete. This unit must be plugged into AC power to receive updates. Do not unplug your unit while an update is in progress. The update is not available during viewing digital text or EPG menu. [ON] : Updates the software when this unit is turned on. [OFF] : Select this if you do not want to do not use this function. Default Setting – You can reset the unit to its original factory settings. Press ENTER while [Select] option is selected. Select [Yes] on the pop-up message to return to the default setting. Displaying the channel information In DVB-T or DAB mode, press DISPLAY to display the information displayed on-screen. If you press DISPLAY twice, the signal strength and quality will appear on the screen. a b a Indicates channel number, station name. b Indicates the channel signal strength, quality. 12 In DVB-T or DAB mode, press CH LIST to display the channel list. Select your desired channel using the v V and press ENTER to change another channel. You can switch the channel list to All or Favorite by pressing b B. DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 13 Viewing a Teletext service Using the digital EPG ON REMOTE 1 Select the DVB-T or DAB mode: MODE 2 Displays the EPG menu: EPG 3 Select a program: vVbB 4 Exit the EPG menu: EPG or RETURN Teletext is a free broadcasting service by some TV stations which gives up-to-the-minute information on news, weather, television programs, share prices and many other topics. The unit gives you access to teletext which is greatly improved in various aspects such as text and graphics. This teletext can be accessed by special teletext services and specific services which broadcast teletext. Using the digital EPG - more you can do About the digital EPG The digital EPG shows a table of scheduled digital TV programs and detailed information about individual program. The digital EPG screen consists of program information, channel list and general program list. Note that the unit’s clock must be set to the correct time and date to ensure all relevant EPG information is displayed. In DVB-T mode, use numbered (0-9) buttons or CH - / + on the remote control to change the channel which broadcast teletext. Press TEXT to access on the teletext. Follow the indications on teletext and move onto the next or previous step by pressing color (Red or Green) or v V buttons. Press TEXT or RETURN (O) to turn the teletext off and return to TV viewing. Selecting teletext page Enter the desired page number as a three digit number with the numbered buttons. If during selection you press a wrong number, you must complete the three digit number and then enter the correct page number again. Use Red/Green buttons to move up and down pages. Special Teletext Functions MIX button – Displays the teletext pages superimposed on the TV picture. To switch the TV picture off press this button again. INDEX button – The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. 13 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 14 Displaying Disc Information Playing a Disc ON REMOTE ON REMOTE 1 Select the disc mode: MODE 1 Select the disc mode: MODE 2 Press DISPLAY: DISPLAY 2 Open the disc tray: Z - OPEN/CLOSE vV 3 Insert a Disc: 4 Adjust the Display menu settings: b B / ENTER 4 Close the disc tray: Z OPEN/CLOSE 5 To return the exit: DISPLAY 5 Start playback: N PLAY 6 To stop playback: x STOP 3 Select a item: Displaying Disc Information - more you can do Playing a Disc - more you can do You can select an item by pressing vV and change or select the setting by pressing b B or using the numbered buttons (0-9). Stops the playback Current title number/total number of titles Current chapter number/total number of chapters Elapsed playing time Selected total time of current title/file x ” appears on The unit records the stopped point depending on the disc. “ Xx the screen briefly. Press PLAY (N) to resume playback (from the scene point). x ) again or unload the disc (“ x ” appears on the screen), If you press STOP (x the unit will clear the stopped point. Xx = Resume Stop, x = Complete Stop) The resume point may be cleared (X when a button is pressed (for example : POWER, OPEN/CLOSE, etc). Playing a DVD that has a menu Selected audio language or channel DVD Most DVD now have menus which load first before the film begins to play. You can navigate these menus using vV b B or number button to highlight an option. Press ENTER to select. Selected subtitle Selected angle/total number of angles Playing a DVD VR disc Symbol Used in this Manual ALL All discs and file listed below ACD Audio CDs DVD DVD and finalized DVD±R/RW CD-G CD-G discs MP3 MP3 files DivX DivX files WMA WMA files This unit will play DVD-RW disc that is recorded using the Video Recording (VR) format. When you insert a DVD VR disc, the menu will appear on the screen. Use vV to select a title then press PLAY (N). To display DVD-VR menu, press DVD MENU or TITLE. Some DVD-VR disc are made with CPRM data by DVD RECORDER. Player does not support these kinds of discs. Skip to the next/previous chapter/track/file ALL Press SKIP (>) to move to the next chapter/track/file. Press SKIP (.) to return to the beginning of the current chapter/track/file. Press SKIP (.) twice briefly to step back to the previous chapter/track/file. 14 DV589H-E.BFRALLK_6716_ENG Pause a playback 1/26/10 7:45 PM Page 15 Watching an enlarged video image ALL Press PAUSE/STEP (X) to pause playback. Press PLAY (N) to continue playback. Frame-by-Frame playback DVD DivX Press PAUSE/STEP (X) repeatedly to play Frame-by-Frame playback. Playing repeatedly DVD DivX During playback or pause mode, press ZOOM repeatedly to select zoom mode. You can move through the zoomed picture using vVb B buttons. Press CLEAR to exit. (100 % p 200 % p 300 % p 400 % p 100 %) Viewing the title menu DVD Press TITLE to display the disc's title menu, if available. ALL Press REPEAT repeatedly to select an item to be repeated. The current title, chapter or track will be played back repeatedly. To return to normal playback, press REPEAT repeatedly to select [Off]. Viewing the DVD menu Fast forward or fast reverse Starting play from selected time DVD DivX ACD WMA MP3 Press SCAN (m or M) to play fast forward or fast reverse during playback. You can change the various playback speed by pressing SCAN (m or M) repeatedly. Press PLAY (N) to continue play at normal speed. - DVD, DivX: mmb P mm P mb P m / M p MB p MM p MMB - ACD, WMA, MP3: mx8 P mx4 P mx2 / Mx2 p Mx4 p Mx8 Repeating a specific portion (A-B) DVD DivX ACD DVD Press DVD MENU to display the disc menu, if available. DVD DivX Searches for the starting point of entered time code. Press DISPLAY then select clock icon. Enter a time then press ENTER. For example, to find a scene at 1 hour, 10 minutes, and 20 seconds, enter "11020" and press ENTER. If you enter the wrong number, press CLEAR to enter again. Last Scene Memory DVD ACD Press A-B at the beginning of the portion you wish to repeat and again at the end of the portion. Your selected portion will be repeated continually. To return to normal playback, press A-B to select [Off]. This unit memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the player or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. Selecting a subtitle language Screen Saver DVD DivX During playback, press SUBTITLE ( language. ) repeatedly to select a desired subtitle Watching from a different angle DVD If the angle indicator appears on the screen for a moment, you can select a different camera angle by pressing ANGLE ( ) repeatedly. Hearing a different audio DVD DivX CD-G During playback, press AUDIO ( ) repeatedly to switch between the available audio languages, channels or encoding methods. Slow down the playing speed DVD (Forward only) While playback is paused, press SCAN (M) to slow down forward playback. You can change the various playback speed by pressing SCAN (M) repeatedly. Press PLAY ( N) to continue play at normal speed. DivX The screen saver appears when you leave the unit in Stop mode for about five minutes. If the Screen Saver is displayed for five minutes, the unit automatically turns itself off. System Select You must select the appropriate system mode for your TV system. Remove any disc that might be in the unit, press and hold PAUSE/STEP (X) for more than five seconds to be able to select a system (PAL, NTSC). Mixed disc or USB Flash Drive – DivX, MP3/WMA and JPEG When playing a disc or USB Flash Drive contained with DivX, MP3/WMA and JPEG files together, you can select which menu of files you would like to play by pressing TITLE. 15 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 16 Playing a DivX movie file You can enjoy the high quality images such as HD DivX file (720p) with this unit. ON REMOTE 1 Select the disc mode: MODE 2 Open the disc tray: Z 3 Insert a disc: - 4 Close the disc tray: Z 5 Select a movie file from the menu: v V, DVD MENU OPEN/CLOSE OPEN/CLOSE Listening to Music Disc or files ON REMOTE To go directly to file, enter the file number using the numbered buttons (0-9). 6 Start playback: N PLAY 7 To stop playback: x STOP Playing DivX movie file - more you can do Changing the character set to display DivX subtitle correctly Press and hold SUBTITLE for 3 seconds during playback. The language code will appear. Press b B to select another language code until the subtitle is displayed properly and then press ENTER. DivX file requirement DivX file compatibility with this player is limited as follows: • Available resolution size: 1280 x 720 (W x H) pixel • The file names of DivX and subtitle are limited to 37 characters • DivX file extensions: “.avi”, “.mpg”, “.mpeg” • Playable DivX subtitle: SubRip (.srt / .txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt) • Playable Codec format: “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “MP43”, “3IVX” • Only the playback function is supported with DivX 6.0 in the unit • Playable Audio format: “Dolby Digital”, “PCM”, “MP3”, “WMA” • Sampling frequency: within 8 to 48 kHz (MP3), within 32 to 48 kHz (WMA) • CD-R/RW, DVD±R/RW Format: ISO 9660 16 • Bit rate (MP3/WMA): within 8 to 320 kbps (MP3), within 32 to 192 kbps (WMA) Bit rate (DivX file): less than 7.2 Mbps (CD-R/RW) less than 9.7 Mbps (USB Flash Drive, DVD±R/RW ) • Maximum Files/Folders: Less than 600 (total number of files and folders) • This unit can support a DivX file size up to 4 GB. • This player does not support the file that are recorded with GMC*1 or Qpel*2. Those are video encoding techniques in MPEG4 standard, like DivX have. *1 GMC - Global Motion Compensation *2 Qpel - Quarter pixel 1 2 3 4 5 Select the disc mode: Open the disc tray: Insert a disc: Close the disc tray: Select a music from the menu: MODE Z OPEN/CLOSE Z OPEN/CLOSE v V, DVD MENU To go directly to track/file, enter the track/file number using the numbered buttons (0-9). 6 Start playback: 7 To stop playback: N PLAY x STOP Listening to Music Disc or files - more you can do Creating your own program You can play the contents of a disc in the order you want by arranging the order of the musics on the disc. To add a music(s) on the program list, press PROGRAM to enter the program edit mode ( E mark appears on the menu). Select a desired music on the [List] then press ENTER to add the music to the program list. Select a music from the program list then press ENTER to start programmed playback. To clear a music from the program list, select the music you want to clear then press CLEAR in program edit mode. To clear all music from the program list, select [Clear All] then press ENTER in program edit mode. The program is cleared when the disc is removed or the unit is turned off. DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 17 Playing an CD-G disc Viewing photo files - more you can do Once you insert an CD-G disc, a menu appears on the screen. Use vV to N). To display the CD-G menu during select a track then press PLAY (N x) twice. You can display the setup menu by pressing playback, press STOP (x SETUP only when CD-G menu appears on the TV screen. Viewing photo files as a slide show Use vV b B to highlight ( ) icon then press ENTER to start slide show. You can change slide show speed using b B when ( ) icon is highlighted. Displaying file information (ID3 TAG) Skip to the next/previous photo While playing a MP3 file containing file information, you can display the information by pressing DISPLAY repeatedly. Press SKIP (. or >) to view the previous/next photo. MP3/WMA music file requirement Use vV to rotate the photo in full screen counterclockwise or clockwise while viewing a photo in full screen. Rotate a photo MP3/WMA compatibility with this unit is limited as follows: • File extensions: “.mp3”, “.wma” • Sampling frequency: within 8 to 48 kHz (MP3), within 32 to 48 kHz (WMA) • Bit rate: within 8 to 320 kbps (MP3), within 32 to 192 kbps (WMA) • CD-R/RW, DVD±R/RW Format: ISO 9660 • Maximum Files/Folders: Less than 600 (total number of files and folders) Press PAUSE/STEP (X) to pause a slide show. Press PLAY (N) to continue the slide show. Tip: You can listen to music during slide show, if the disc contain music and photo files together. Use vV b B to highlight ( ) icon then press ENTER to start slide show. Press and hold v V to move previous or the next page. Pause a slide show Listening to music during slide show Watching a enlarged photo image While viewing a photo in full screen, press ZOOM repeatedly to select zoom mode. You can move through the zoomed photo using vVb B buttons. Press CLEAR to exit. Viewing photo files ON REMOTE 1 2 3 4 5 Select the disc mode: Open the disc tray: Insert a disc: Close the disc tray: Select a photo file on the menu: MODE Z OPEN/CLOSE Z OPEN/CLOSE v V, DVD MENU Photo file requirement JPEG file compatibility with this unit is limited as follows: • File extensions: “.jpg” • Photo size: Less than 2 MB recommended • CD-R/RW, DVD±R/RW Format: ISO 9660 • Maximum Files/Folders: Less than 600 (total number of files and folders) To go directly to file, enter the file number using the numbered buttons (0-9). 6 Display the selected file in full screen: 7 To return to the menu: N PLAY x STOP 17 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 18 • Recording format: MP3 file • Encoding Bit rate: 128 Kbps / 160 Kbps / 192 Kbps / 256 Kbps / 320 Kbps • Maximum Files/Folder: Less than 600 (total number of files and folders) USB Direct Recording Connect USB Flash Drive to the unit before recording. Set [REC Birate] option as required. (See page 10) ON REMOTE 1 Select the disc mode: 2 Insert an Audio CD: 3 Select a track: MODE v V, DVD MENU To go directly to track, enter the track number using the numbered buttons (0-9). 4 Start recording: 5 To stop recording: AUDIO x STOP Recordable mode You can record one desired track or all of the tracks in Audio CD to USB Flash Drive. • For track recording: Press AUDIO in play, pause or resume stop mode. • For disc recording: Press AUDIO in complete stop mode. • For program list recording: In stop mode, press AUDIO after selecting a track on the program list. Notes an USB direct Recording • The recording is available only for Audio CD tracks. • If you use this function, the “CD_REC” folder will be created automatically in the USB Flash Driver then the music file(s) is saved in it. • If you remove USB Flash Drive, turn off or open the unit while recording, it can make a malfunction. • If the remaining space on the USB Flash Drive is insufficient, the recording is not available. To increase the free space, delete files in it using your PC. • CD-G disc and Audio CDs encoded in DTS cannot be recorded. • External HDD, Multi Card reader, Multi Partition USB, Locked device and MP3 player are not supported. • You can set the recording speed pressing AUDIO during USB direct recording. - X1 Track: While normal speed recording, you can listen to the music. - X4 Track: While 4X speed recording, you can not listen to the music. 18 The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts and sound recording, may be an infringement of copyrights and constitute a criminal offence. This equipment should not be used for such purposes. Be responsible Respect copyrights DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 19 Setting up the remote to control your TV Using a USB Flash Drive You can play MP3/WMA/JPEG/DivX in the USB Flash Drive with version 2.0/1.1. ON REMOTE 1 Select the disc mode: 2 Connect an USB Flash Drive to the USB port on the unit: 3 Display the menu screen in stop mode: 4 Select a file: MODE O RETURN v V, DVD MENU To go directly to a file, enter the file number using the numbered buttons (0-9). You can operate your TV with the supplied remote control. If your TV is listed in the table below, set the appropriate manufacturer code. While holding down TV POWER button, and press the manufacturer code for your TV with the numerical buttons (see the table below). Release the TV POWER button to complete setting. Manufacturer Code Number LG / GoldStar 1 (Default), 2 Zenith 6, 7 Sony 8, 9 Hitachi 5 Play the file: N 6 Remove the USB Flash Drive: - PLAY 1, 3, 4 Samsung 4 Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. Notes an USB Flash Drive O) only in stop • You can switch USB and DISC mode by pressing RETURN (O mode. • Do not extract the USB Flash Drive in operating. • Regular back up is recommended to prevent data loss. • If you use an USB extension cable or USB HUB, the USB device might not be recognized. • Music files (MP3/WMA), photo files (JPEG) and DivX files can be played. For details of operations on each files, refer to relevant pages. • This unit is not supported when the total number of files is more than 600. • Bit rate: within 8 to 320 kbps (MP3), within 32 to 192 kbps (WMA), less than 6 Mbps (DivX file) • The USB function of this unit does not support all kinds of USB devices. • Digital camera and mobile phone are not supported. • USB port of the unit can not be connected to PC. The unit can not be used as a storage device. 19 DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 20 Language Codes Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu. Language Afar Afrikaans Albanian Ameharic Arabic Armenian Assamese Aymara Azerbaijani Bashkir Basque Bengali; Bangla Bhutani Bihari Breton Bulgarian Burmese Byelorussian Chinese Code 6565 6570 8381 6577 6582 7289 6583 6588 6590 6665 6985 6678 6890 6672 6682 6671 7789 6669 9072 Language Croatian Czech Danish Dutch English Esperanto Estonian Faroese Fiji Finnish French Frisian Galician Georgian German Greek Greenlandic Guarani Gujarati Code 7282 6783 6865 7876 6978 6979 6984 7079 7074 7073 7082 7089 7176 7565 6869 6976 7576 7178 7185 Language Hausa Hebrew Hindi Hungarian Icelandic Indonesian Interlingua Irish Italian Japanese Kannada Kashmiri Kazakh Kirghiz Korean Kurdish Laothian Latin Latvian, Lettish Code 7265 7387 7273 7285 7383 7378 7365 7165 7384 7465 7578 7583 7575 7589 7579 7585 7679 7665 7686 Language Lingala Lithuanian Macedonian Malagasy Malay Malayalam Maori Marathi Moldavian Mongolian Nauru Nepali Norwegian Oriya Panjabi Pashto, Pushto Persian Polish Portuguese Code 7678 7684 7775 7771 7783 7776 7773 7782 7779 7778 7865 7869 7879 7982 8065 8083 7065 8076 8084 Language Quechua Rhaeto-Romance Rumanian Russian Samoan Sanskrit Scots Gaelic Serbian Serbo-Croatian Shona Sindhi Singhalese Slovak Slovenian Spanish Sudanese Swahili Swedish Tagalog Code 8185 8277 8279 8285 8377 8365 7168 8382 8372 8378 8368 8373 8375 8376 6983 8385 8387 8386 8476 Language Tajik Tamil Telugu Thai Tonga Turkish Turkmen Twi Ukrainian Urdu Uzbek Vietnamese Volapük Welsh Wolof Xhosa Yiddish Yoruba Zulu Code 8471 8465 8469 8472 8479 8482 8475 8487 8575 8582 8590 8673 8679 6789 8779 8872 7473 8979 9085 Area Codes Choose an area code from this list. Area Afghanistan Argentina Australia Austria Belgium Bhutan Bolivia Brazil Cambodia Canada Chile China Colombia Congo 20 Code AF AR AU AT BE BT BO BR KH CA CL CN CO CG Area Costa Rica Croatia Czech Republic Denmark Ecuador Egypt El Salvador Ethiopia Fiji Finland France Germany Great Britain Greece Code CR HR CZ DK EC EG SV ET FJ FI FR DE GB GR Area Greenland Hong Kong Hungary India Indonesia Israel Italy Jamaica Japan Kenya Kuwait Libya Luxembourg Malaysia Code GL HK HU IN ID IL IT JM JP KE KW LY LU MY Area Maldives Mexico Monaco Mongolia Morocco Nepal Netherlands Netherlands Antilles New Zealand Nigeria Norway Oman Pakistan Panama Code MV MX MC MN MA NP NL AN NZ NG NO OM PK PA Area Paraguay Philippines Poland Portugal Romania Russian Federation Saudi Arabia Senegal Singapore Slovak Republic Slovenia South Africa South Korea Spain Code PY PH PL PT RO RU SA SN SG SK SI ZA KR ES Area Sri Lanka Sweden Switzerland Taiwan Thailand Turkey Uganda Ukraine United States Uruguay Uzbekistan Vietnam Zimbabwe Code LK SE CH TW TH TR UG UA US UY UZ VN ZW DV589H-E.BFRALLK_6716_ENG 1/26/10 7:45 PM Page 21 Specifications Troubleshooting Symptom No power. Cause The power cord is disconnected. Correction Plug the power cord into the wall outlet securely. General Power requirements Power consumption Dimensions (Approx.) The power is on, but the unit does not work. No disc is inserted. No picture. The TV is not set to receive the signal from the unit. Select the appropriate video input mode on the TV. The video cable is not connected securely Connect the video cable securely. Inputs The channel is not found or stored. Check your antenna connection. USB IN Bus power supply ANTENNA IN The equipment connected with the audio cable is not set to receive the signal from the unit. Select the correct input mode of the audio amplifier. The AUDIO options are set to the wrong position. Set the AUDIO settings to the correct position. An unplayable disc is inserted. Insert a playable disc. (Check the disc type and regional code.) The rating level is set. Change the rating level. The remote control is not pointed at the remote sensor on the unit. Point the remote control at the remote sensor of the unit. The remote control is too far from the unit. Operate the remote control closer to the unit. No sound. The unit does not start playback. Insert a disc. Net Weight (Approx.) Operating temperature Operating humidity Laser Television system Signal system 4 pin (USB 2.0 / 1.1 standard) 5V 200 mA Antenna input, 75 Ω Outputs Video Output Component Video Output HDMI Video/Audio Output Audio Output The remote control does not work properly. AC 200 - 240 V, 50 / 60 Hz 11 W (430 x 35 x 200) mm (W x H x D) without foot 1.7 kg 5 °C to 35 °C 5 % to 90 % Semiconductor laser DVB-T Standard Compliant PAL / NTSC Digital Output (Coaxial) 1.0 V (p-p), 75 Ω, sync negative, RCA jack (L, R) x 1 / SCART(TO TV) (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 19 pin (HDMI standard, Type A, Version 1.2) 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1 / SCART(TO TV) 0.5 V (p-p), 75 Ω, RCA jack x 1 Accessories Video/Audio cable, Remote Control, Battery, RF cable Designs and specifications are subject to change without prior notice. 21 As an ENERGY STAR® Partner, LG has determined that this product or product models meet the ENERGY STAR® guidelines for energy efficiency. ENERGY STAR® is a U.S. registered mark.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project