OWNER'S MANUAL Prior to installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-2, EN 61000-3 Norm). FRANÇAIS LG Room Air Conditioner ENGLISH LG ESPAÑOL IMPORTANT • Please read this owner's manual carefully and thoroughly before installing and operating your room air conditioner. • Please retain this owner's manual for future reference after reading it thoroughly. ############## Room Air Conditioner Owner’s Manual TABLE OF CONTENTS Safety Precautions.........................3 FOR YOUR RECORDS Write the model and serial numbers here: Model # Prior to Operation ..........................9 Serial # You can find them on a label on the side of each unit. Dealer's Name Introduction ..................................10 Electrical Safety ...........................11 Operating Instructions.................12 Maintenance and Service ............25 Date Purchased ■ Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues. READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. PRECAUTION • Contact the authorized service technician for repair or maintenance of this unit. • Contact the installer for installation of this unit. • The air conditioner is not intended for use by young children or invalids without supervision. • Young children should be supervised to ensure that they do not play with the air conditioner. • When the power cord is to be replaced, replacement work shall be performed by authorized personnel only using only genuine replacement parts. • Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only. 2 Room Air Conditioner Safety Precautions Safety Precautions This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. ■ The meanings of the symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. ■ Installation Do not use damaged power cords, plugs, or a loose socket. For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. Always use the power plug and socket with the ground terminal. • There is risk of fire or electric shock. • There is risk of fire or electric shock. • There is risk of electric shock. Install the panel and the cover of control box securely. Do not modify or extend the power cord. Do not install, remove, or reinstall the unit by yourself (customer). • There is risk of fire or electric shock. • There is risk of fire or electric shock. • There is risk of fire, electric shock, explosion or injury. Owner’s Manual 3 ENGLISH To prevent the injury of the user or other people and property damage, the following instructions must be followed. ■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. Safety Precautions Be cautious when unpacking and installing the product. For installation, always contact the dealer or an Authorized Service Center. Do not install the product on a defective installation stand. • Shape edges could cause injury. Be especially careful of the sharp edges. • There is risk of fire, electric shock, explosion, or injury. • It may cause injury, accident, or damage to the product. Be sure the installation area does not deteriorate with age. Install the indoor unit on the wall where the height from the floors more then 8ft(2.4m) Do not handle the pipe by yourself(Costomer) • If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury. • There are sharp moving parts that could cause personal injury. • High-Pressure refrigent may cause personal injury. 8ft(2.4m) ■ Operation Use a dedicated outlet for this appliance. Grasp the plug to remove the cord from the outlet. Do not touch it with wet hands. • There is risk of fire or electric shock. • There is risk of fire or electric shock. 4 Room Air Conditioner Do not allow water to run into electric part. • There is risk of fire, failure of the product, and/or electric shock. Safety Precautions Do not place a heater or other appliances near the power cable. Do not store of use flammable gas or combustibles near the air conditioner. • Moisture may condense and wet or damage furnishings. • There is risk of fire or product failure. x Wa Thinner Do not use the product in a tightly closed space for a long time. When flammable gas leaks, turn off the gas and open a window for ventilation before turning the product on. Do not use the telephone or turn switches on or off. Unplug the unit if strange sounds odors or smoke comes from it. • Oxygen deficiency could occur. • Some ventilation by opening window is necessary for the fresh air • There is risk of explosion or fire. • There is risk of fire, Product faiure, and/or electric shock. Stop operation and close any window in storm or hurricane before the hurricane arrives. Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.) When the product is soaked (flooded or submerged), contact an Authorized Service Center. • There is risk of property damage, failure of product, or electric shock. • There is risk of physical injury, electric shock, or product. • There is risk of electrical shock. Owner’s Manual 5 ENGLISH • There is risk of fire, failure of the product, and/or electric shock. Do not let the air conditioner run for a long time when the humidity is very high and a door or a window is left open. Safety Precautions Ventilate the product from time to time when operating it together with a stove, etc. Unplug the appliance before performing cleaning or maintenance. When the product is not be used for a long time disconnect the power supply plug or turn off the breaker. • There is risk of fire or electrical shock. • There is risk of electric shock. • There is risk of product damage or failure, or unintended operation. ■ Installation Take care to ensure that nobody could step on or fall onto the outdoor unit. Do not insert hands or other objects through the air inlet or outlet while the air conditioner is plugged in. Always check for gas(refrigerant) leakage after installation or repair of product. • There could result in personal injury and product damage. • There are sharp and moving parts that could cause personal injury. • Low refrigerant levels may cause product failure. Install the drain hose to ensure that water is drained away properly. Keep level even when installing the product. Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. • A bad connection may cause water leakage. • To avoid vibration or water leakage. • It may cause a problem for your neighbors. 90˚ 6 Room Air Conditioner Safety Precautions ■ Operation Do not install the product where it will be exposed to sea wind (salt spray) directly. Do not direct airflow at room occupants. • Avoid personal injury. • It may cause corrosion in the product. Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or inefficient operation. • This could damage your health. Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air conditioner, not a precision refrigeration system. Do not block the inlet or outlet of air flow. Use a soft cloth to clean. Do not use harsh detergents, solvents, etc. • There is risk of damage or loss of property. • It may cause product failure. • There is risk of fire, electric shock or damage to the plastic parts of the product. Do not touch the metal parts of the product when removing the air filter. They are very sharp! Do not step on or put anything on the product. (outdoor unit) Always insert the filter securely. Clean the filter every two weeks or more often if necessary. • There is risk of personal injury. • There is risk of personal injury and failure of product. • A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage. Owner’s Manual 7 ENGLISH Use two or more people to lift and transport the air conditioner. Safety Precautions Do not drink the water drained from the unit. Use a firm stool or ladder when cleaning or maintaining the air conditioner. Replace all the batteries in the remote. • It is not sanitary and could cause serious health issues. • Be careful and avoid personal injury. • There is risk of fire or explosion. ■ Disuse Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire. If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not use the remote if the batteries have leaked. • They may burn or explode. • The chemicals in batteries could cause burns or other health hazards. 8 Room Air Conditioner Prior to operation Prior To Operation Preparing For Operation Usage 1. Being exposed to direct airflow for a long time may be hazardous to your health. Do not expose occupants, pets, or plants to direct airflow for a long time. 2. Ventilate the room when the air conditioner is used with other heating devices. Otherwise the oxygen supply may be inadequate. 3. Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices, food, pets, plants, or art objects). Such use may damage your properties. Cleaning And Maintenance 1. Do not touch the metal parts of the unit when removing the filter. Injury can occur. 2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to electric shock. 3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a very high speed during operation. There is a possibility of injury if the unit power is accidently turned on while the interior of the unit is being cleaned. Service For repair and maintenance, contact your authorized service dealer. Owner’s Manual 9 ENGLISH 1. Contact an installation specialist for installation. 2. Plug in the power plug properly. 3. Use a dedicated circuit. 4. Do not use an extension cord. 5. Do not start/stop operation by plugging/unplugging the power cord. 6. If the cord/plug is damaged, ony replace it with an authorized replacement part. Introduction Introduction Symbols Used In This Manual This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that may cause harm to the air conditioner. NOTICE This symbol indicates special notes. Features • This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features. Indoor Air Inlet Air Filter Front Panel Signal Receptor Outdoor (Side) (Rear) Air intake vents Piping Air outlet vents 10 Room Air Conditioner Electrical Safety Electrical Safety To minimize the risk of electric shock, you must alway plug into a grounded oulet • Do not cut or remove the grounding prong from the power plug. • Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the house wiring. • If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and circuit checked by a qualified electrician. Owner’s Manual 11 ENGLISH • This appliance must be properly grounded. Operating Instruction Operating Instruction How To Insert The Batteries Remove the battery cover by pulling it according to the arrow direction. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. Reattach the cover by sliding it back into position. NOTICE Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. Storage And Tips For Using The Remote Controler • The remote controler may be stored by mounting it on a wall. • To operate the room air conditioner, aim the remote control at the signal receptor. Signal Receptor Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.) Operation Indication Lamps On/Off : Lights up during the system operation, error code and auto restart setting. Sleep mode : Lights up during sleep mode auto operation. Plasma : The function illustrates its dynamic mode by using a multiple lighting system. Timer : Lights up during timer operation. Defrost mode : Lights up during defrost mode or *hot start operation (Heat pump model only) OUT DOOR Outdoor unit : Lights up during outdoor unit operation. (Cooling model only) operation Power Display : Indicates the setting temperature and operation mode. Operation Cooling, heating, mode Dehumidification Standard Mode Auto operation mode Too hot Hot Comfortable Cold Too cold Jet Test Cool/Heat operation Auto clean Setting Shape of display temperature * Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out from unit. * In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat exchanger coils to maintain the efficiency. 12 Room Air Conditioner Operating Instruction Remote Control Operations Controls 5 1 6 3 4 2 7 11 8 13 10 CANCEL ON OFF 9 12 17 19 18 14 16 SET AUTO CLEAN 15 Flip-up door (opened) Operation Mode Cooling Operation Auto Operation Healthy Dehumidification Operation Heating Operation • Cooling Model( ), Heat Pump Model( ) 17. AUTO CLEAN (OPTIONAL) Used to set Auto Clean mode. 18. ˚C TO ˚F SWITCHING BUTTON Used to switch temperature reading from Centigrade to Fahrenheit. 19. LCD LUMINOSITY BUTTON(OPTIONAL) Used to adjust LCD luminosity. Owner’s Manual 13 ENGLISH Signal transmitter 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5. JET COOL Used to start or stop the speed cooling.(speed cooling operates super high fan speed in cooling mode.) 6. CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 7. ON/OFF TIMER BUTTONS Used to set the time of starting and stopping operation. (See page 21) 8. TIME SETTING BUTTONS Used to adjust the time. (See page 21) 9. TIMER SET/CANCEL BUTTON Used to set the timer when the desired time is obtained and to cancel the Timer operation. (See page 21) 10. SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation. (See page 21) 11. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating. (See page 22) 12. ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. 13. NEO PLASMA(OPTIONAL) Used to start or stop the plasmapurification function. (See page 19) 14. HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (OPTIONAL) Used to set the desired horizontal airflow direction. 15. RESET BUTTON Used prior to resetting time. 16. 2nd F Button Used prior to using modes printed in blue at the bottom of buttons. (See page 20) Operating Instruction Cooling operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 ON Auto Healthy Dehumidification Heating (Heat pump model only) Close the door of the remote controller. Set the temperature lower than the room temperature. The temperature can be set within a range of 18°C~30°C(64°F~86°F) at intervals of 1°C(2°F). To raise the temperature To lower the temperature 4 Set the fan speed again with the door of the remote controller still closed. You can select the fan speed in four steps-low, medium, high and CHAOS. Each time the button is pressed, the fan speed mode is shifted. Gentle Breeze by the CHAOS logic ❏ For fresher feeling, press the Indoor fan speed selector and set to CHAOS mode. In this mode, the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic. 14 Room Air Conditioner Operating Instruction Auto operation Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Auto Operation, press the operation mode selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling ON ENGLISH 1 3 Auto Healthy Dehumidification Heating (Heat pump model only) The temperature and fan speed are automatically set by the electronic controls based on the actual room temperature. If you want to change the set temperature, press the Room Temperature Setting buttons. The cooler or warmer you feel, the more times (up to two times) you should press the button. The set temperature will be changed automatically. To raise the temperature To lower the temperature During Auto Operation ❏ You cannot control the indoor fan speed. It has already been set by the Fuzzy rule. ❏ If the system is not operating as desired, manually switch to another mode. The system will not automatically switch from the cooling mode to the heating mode, or from heating mode to cooling mode, it must be done by manually resetting. ❏ During Auto Operation, pressing the CHAOS swing button makes the horizontal louvers swing up and down automatically. If you want to stop auto-swing, press the CHAOS swing button again. Owner’s Manual 15 Operating Instruction Healthy dehumidification operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Healthy Dehumidification Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 ON Auto Healthy Heating Dehumidification (Heat pump model only) Set the fan speed again with the door of the remote controller still closed. You can select the fan speed in four steps-low, medium, high, or CHAOS. Each time the button is pressed, the fan speed mode is shifted. Gentle Breeze by the CHAOS logic ❏ For fresher feeling, press the Indoor Fan Speed Selector and set to CHAOS mode. In this mode, the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic. During Healthy Dehumidification Operation ❏ If you select the dehumidification mode on the operation selection button, the product starts to run the dehumidification function. It automatically sets the room temp. and airflow volume to the best condition for dehumidification, based on the sensed current room temp. In this case, however, the setting temperature. is not displayed on the remote controller and you are not able to control the room temperature. either. ❏ During the healthy dehumidification function, the airflow volume is automatically set according to the optimization algorithm responding to the current room temp. status, so the room condition is kept healthy and comfortable even in the very humid season. 16 Room Air Conditioner Operating Instruction Heating operation (Heat pump model only) ENGLISH 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. To select Heating Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 ON Auto Healthy Heating Dehumidification (Heat pump model only) Close the door of the remote controller. Set the temperature higher than the room temperature. The temperature can be set within a range of 16°C~30°C(60°F~86°F) at intervals of 1°C(2°F). To raise the temperature To lower the temperature 4 Set the fan speed again with the door of the remote controller still closed. You can select the fan speed in four steps–low, medium, high and CHAOS. Each time the button is pressed, the fan speed mode is shifted. Gentle Breeze by the CHAOS logic ❏ For fresher feeling, press the Indoor Fan Speed Selector and set to CHAOS mode. In this mode, the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic. Owner’s Manual 17 Operating Instruction Jet cool operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Press the Jet Cool button to operate the speed cooling mode and the unit will operate at super high fan speed on cooling mode for 30 minutes. 3 To cancel the Jet Cool mode, press the Jet Cool button, the fan speed button or the room temperature setting button again and the unit will operate at high fan speed on cooling mode. or or NOTICE ❏ During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely high speed for 30 minutes setting the room temperature. automatically to 18°C. It is especially used to cool the room temperature. quickly in a hot summer. In heat pump mode or auto changeover mode, however, the JET COOL function is not available. ❏ In order to return to the normal cooling mode from the JET COOL mode, just press the operation mode selection button, airflow volume selection, temperature. setting button or the JET COOL button again. 18 Room Air Conditioner Operating Instruction NEO PLASMA purification operation(Optional) ENGLISH 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller. Press the PLASMA button. Operation will start when the button is pressed and stop when the button is pressed again. 3 Set the fan speed again with the door of the remote controller closed. You can select the fan speed in four steps-low, medium, high or CHAOS. Each time the button is pressed, the fan speed mode is shifted. ❈ Air purifying operation (NEO PLASMA) can be with cooling, Heating or any other operations. NEO PLASMA Air Purifying Operation only If you press the only PLASMA button, only PLASMA purification function operates. Then, fan speed is low. You can select the fan speed in four steps-low, medium, high or CHAOS. Each time the Indoor Fan Speed Selector button is pressed, the fan speed mode is shifted. Owner’s Manual 19 Operating Instruction 2nd F operation 1 Press the Start/Stop button. The unit will respond with a beep. 2 Open the door of the remote controller and press the 2nd Function button to operate functions printed blue color under buttons. (Check the indication of 2nd function on the display of the remote controller.) 3 2nd function disappears in a short time automatically or when the button is pressed again. CANCEL ON OFF SET AUTO CLEAN For more details, refer to functions next pages. 20 Room Air Conditioner Operating Instruction Additional Features Sleep mode 2. The Timer is programmed in one-hour increments by pressing the Sleep Mode Auto button 1 to 7 times. The sleep mode is available for 1 to 7 times. To alter the time period in steps of 1 hour, press the Sleep Mode Button while aiming at air conditioner. 3. Make sure the Sleep Mode Auto LED lights up . To cancel the Sleep Mode, press the sleep Mode Auto button several times until the star( ) disappears from the operation display. NOTICE The Sleep Mode will be operated at slow fan speed (cooling) or medium fan speed (heat pump only) for a comfortable sleep. In cooling mode or healthy dehumidification mode: The setting temperature will automatically rise by 1°C(2°F) over the next 30 minutes and by 2°C(4°F) in 1 hour for a comfortable sleep. Setting the time 1. Time can be set only when you press the Reset button. When you replace the batteries, you should press the reset buttons to reset the time. Press the Start/Stop button. 2. Press 2nd F button and check if 2nd F icon is on. 3. Press the Time Setting buttons until the desired time is set. CANCEL 4. Press the Timer SET button. SET NOTICE Check the indicator for A.M. or P.M. Delay start/Pre-set stop 1. Make sure the time is set correctly on the display of the remote controller. 2. Press 2nd F button. 3. Press the ON/OFF Timer buttons to turn Timer on or off. ON OFF 4. Press the Time Setting buttons until the desired time is set. CANCEL 5. To set the selected time, press the Timer setting button aiming the remote controller at the signal receptor. To cancel the timer setting Check if 2nd F icon is off. Press the Timer Cancel button aiming the remote controller at the signal receptor. (The timer lamp on the air conditioner and the display will go out.) SET CANCEL SET NOTICE Select one of the following four types of operation. Delay OFF Timer Delay ON Timer with the unit running Delay OFF and ON Timer Delay ON and OFF Timer Owner’s Manual 21 ENGLISH 1. Press the Sleep Mode Auto button to set the time you want the unit to stop automatically. Operating Instruction Vertical Airflow Direction Control The up/down airflow (Vertical Airflow) can be adjusted by using the remote control. 1. Press the Start/Stop button to start the unit. 2.Open the door on the remote control. Press Chaos Swing button and the louvers will swing up and down. Press the Chaos Swing button again to set the vertical louver at the desired airflow direction. NOTICE ❏ If you press the CHAOS swing button, the vertical airflow direction is changed automatically based on the CHAOS algorithm to distribute the air in the room evenly and at the same time to make the human body feel most comfortable, as if enjoying a natural breeze. ❏ Always use the remote control to adjust the up/down airflow direction. Manually moving the vertical airflow direction louver by hand could damage the air conditioner. ❏ When the unit is shut off, the up/down airflow direction louver will close the air outlet vent of the system. To adjust left/right(Horizontal Airflow) direction Ensure unit is turned off before adjusting the horizontal airflow direction control. Carefully open vertical louver to allow access to the horizontal airflow direction. Adjust the left/right airflow direction by hand. Air Circulation Mode Circulates the room air without cooling or heating. 1. Press the Start/Stop button. the unit will respond with a beep. 2. Open the door on the remote control. Press the Air Circulation button. Close the door on the remote control. Now each time that you press the Indoor Fan Speed Selector, the fan speed is shifted from low to CHAOS and back to low again. CHAOS Air Fan speed is on low. Fan speed is on medium. Fan speed is on high. NOTICE ❏ CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically changed from high to low or vice versa, depending on the ambient temperature. 22 Room Air Conditioner Operating Instruction Auto clean (Optional) NOTICE ❏ During Auto Clean function, moistures left in indoor units after Cooling Operation or Healthy Dehumidification Operation can be removed. ❏ During Auto Clean function, only Start/Stop button, Plasma button and AUTO CLEAN button are available. Forced operation Operation procedures when the remote control can't be used. The operation will be started if the ON/OFF button is pressed. If you want to stop operation, re-press the button. ON/OFF button Cooling Model Room Temp. ≥ 24°C(75.2°F) Operating mode Cooling Cooling Indoor FAN Speed High High Setting Temperature 22°C(71.6°F) 22°C(71.6°F) Heat pump Model 21°C(69.8°F) ≤ Room Temp. < 24°C(75.2°F) Room Temp. < 21°C(69.8°F) Healthy Dehumidification Heating High High 23°C(73.4°F) 24°C(75.2°F) Test operation During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room temperature and resets in 18 minutes. During test operation, if remote controller signal is received, the unit operates as remote controller sets. If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound 1 "beep". If you want to stop the operation, re-press the button. Owner’s Manual 23 ENGLISH 1. Whenever you press the AUTO CLEAN button, Auto Clean Function will be reserved and cancelled. 2. Auto Clean function works before and after cooling or dehumidification mode. For details, refer to the below points. 3. When the unit is started after the reservation of Auto Clean ,the Cool Start function operates and indoor Fan is started after 20 seconds. 4. When you press Start/Stop button to turn off the unit after the you have reserved Auto Clean function, the air-conditioner circulates the indoor air in the Auto Clean mode with no more Cooling or Dehumidification operation. It lasts for 30 minutes. 5. If you press the AUTO CLEAN button again during the product operation , Auto Clean function will be cancelled. AUTO CLEAN Operating Instruction Display Luminosity (Optional) The Display Luminosity can be adjusted by using the remote control. Press the start/stop button to start the unit. Open the door on the remote control, press the 2ndF button and, press display luminosity button. Display will be dark. Press the button again to set bright display. Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. So there is no need of activating this function by pressing any key or button. In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3 minutes later. As the compressor starts, the fan speed also resumes its previous setting mode. Helpful information Fan speed and cooling capacity. The cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. High Speed NOTICE Auto restart function has set enable as factory default. But customer can set up by following this instruction. To disable function - Press and hold the ON/OFF button for 6 seconds, then the buzzer sound 2 "beep" and the indicator lamp (1) blinks 4 times. To enable function - Press and hold the ON/OFF button for 6 seconds, then the buzzer sound 2 "beep" and the indicator lamp (1) brights 4 times. 24 Room Air Conditioner Maintenance and Service Maintenance And Service ENGLISH Before performing any maintenance, turn off the main power to the system. Indoor Unit Grille, Case, and Remote Control Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives. NOTICE Supply power must be disconnected before cleaning the indoor unit. Air inlet vent Air filters (behind front panel) Vertical louver Horizontal louver Air outlet vent Air filters The air filters behind the front grille should be checked and cleaned once in every 2 weeks or more often if neccessary. 1. Open the front panel as shown. 2. Pull the filter tab slightly forward to remove the filter. 3. Clean the filter with a vacuum cleaner or warm, soapy water. • If dirt is conspicuous, wash with a solution of detergent in lukewarm water. • If hot water (40°C(104°F) or more) is used, it may be deformed. 4. After washing with water, dry well in the shade. 5. Re-install the air filter. Front panel NEO PLASMA filter (Optional) The NEO PLASMA filter behind the air filters should be checked and cleaned once in every 3 months or more often if necessary. 1. After removing the air filters, pull slightly forward to remove the NEO PLASMA filter. 2. Clean NEO PLASMA filter with the vacuum cleaner. If it is very dirty, wash it with water. 3. Note the cuts of electric discharge lines. 4. Re-install the NEO PLASMA filter to the original position. Plasma filter TRIPLE DEODORIZER filter (Optional) 1. After removing the air filters, pull slightly forward to remove the TRIPLE DEODORIZER filter. 2. Dry in the sunlight for two hours. 3. Re-install the TRIPLE DEODORIZER filter to the original position. Don't touch this NEO PLASMA Filter within 10 seconds after opening he inlet grille, it may cause an electric shock. Never use any of the followings: • Water hotter than 40°C(104°F) Could cause deformation and/or discoloration. • Volatile substances Could damage the surfaces of the air conditioner. Pow d er G a s o li n e Owner’s Manual 25 Maintenance and Service Outdoor Unit The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned. NOTICE (Side) (Rear) Air intake vents Piping Air outlet vents Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs. Common Problems And Solutions Before calling for service If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is plugged into a proper outlet. 2. Check the fuse or circuit breaker. 3. Check whether the voltage is unusually high or low. Air does not feel cold enough on the cooling setting 1. Ensure that the temperature settings are correct. 2. Check to see if the air filter is clogged with dust. If so, replace the filter. 3. Ensure that the air flow from the outside is not obstructed and that there is a clearance of over 20" between the back of the air conditioner and the wall or fence behind it. 4. Close all doors and windows and check for any source of heat in the room. Before calling for service, please review the following list of common problems and solutions. The air conditioner is operating normally when: • You hear a pinging noise. This is caused by water being picked up by the fan on rainy days or in highly humid conditions. This feature is designed to help remove moisture in the air and improve cooling efficiency. • You see water dripping from the rear of the unit. Water may be collected in the base pan in highly humid conditions or on rainy days. This water overflows and drips from the rear of the unit. • You hear the fan running while the compressor is silent. This is a normal operational feature. 26 Room Air Conditioner Maintenance and Service Troubleshooting The air conditioner may be operating abnormally when: Air conditioner does not start Air conditioner does not cool as it should Possible Causes What To Do ■ The air conditioner is unplugged. • Make sure the air conditioner plug is pushed completely into the outlet. ■ The fuse is blown/circuit breaker is tripped. • Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. ■ Power failure. • If power failure occurs, turn the mode control to Off. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload. ■ Airflow is restricted. • Make sure there are no curtains, blinds, or furniture blocking the front of the air conditioner. ■ The air filter is dirty. • Clean the filter at least every 2 weeks. See the care and Maintenance section. ■ The room may have been hot. • When the air conditioner is first turned on, you need to allow time for the room to cool down. ■ Cold air is escaping. • Check for open furnace floor registers and cold air returns. ■ Cooling coils have iced up. • See Air Conditioner Freezing Up below. * You can refer to the Energy Star program in detail at www.energystar.gov. Owner’s Manual 27 ENGLISH Problem Memo 28 Room Air Conditioner P/No.: 3828A20434L Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project