LG | AR805TS | User's Manual | LG AR805TS User's Manual

OWNER’S MANUAL
DIGITAL A/V RECEIVER
SYSTEM
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
AR805TS (AR805TS, SR85TS-F/S/C/W)
P/NO : MFL63267063
2
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
Cautions and Warnings
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service centre.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the cord
exits the appliance. To disconnect power from the
mains, pull out the mains cord plug. When installing
the product, ensure that the plug is easily accessible.
Safety Information
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the battery
from the equipment:
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
1
Safety Information
Remove the old battery or battery pack, follow the
steps in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do not
dispose of batteries or battery together with other
waste. It is recommended that you use local, free
reimbursement systems batteries and accumulators.
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
3
4
Contents
Contents
1
Safety Information
2
Cautions and Warnings
3
Copyrights
2
Preparation
6
Introduction
3
Installation
12
Installing speakers
13
Connecting speakers
14
Connecting to Your TV
14
Video/Audio (Left/Right)
connection
15
HDMI connection
16
Resolution Setting
16
Connecting TV or components
with HDMI jack
17
Connecting components with
analog video and audio jacks
17
17
AV IN 1 connection
AV IN 2 connection
6
About the “ ” Symbol
Display
18
6
Symbols Used in this
Manual
18
Optical digital audio
connection
6
Accessories
18
Coaxial digital audio
connection
7
Required cables
Connecting components with
Digital Audio jacks
8
Remote control
19
Connecting the portable device
10
Front panel
19
Connecting the antennas
Rear panel
20
Connecting the headphones
21
Settings
11
21
Adjusting the Setup
Settings
21
[Language] Menu
21
[Display] Menu
22
[Audio] Menu
23
[Others] Menu
Contents
4
5
Operation
Maintenance
24
Turning On the unit
24
Selecting the input source
25
Adjusting the speaker levels
26
Enjoying various sound mode
37
Handling the Unit
Sound Effect
Troubleshooting
27
Bass Blast
27
Setting the USER EQ
38
Listening to FM/AM radio
27
Automatic tuning
27
Manual tuning
28
Presetting radio stations
28
Tuning to preset stations
28
Deleting the preset stations
28
Deleting all the preset
stations
29
Playing the USB device
29
Basic operations
31
Listening to music
32
Playing a movie file
34
1
6
26
27
5
2
Troubleshooting
7
Appendix
40
Trademarks and Licenses
41
Specifications
3
4
5
Viewing a photo
35
Dimmer
35
Screen Saver
36
Using the Sleep Timer
36
Using microphone
6
7
6
Preparation
2
Preparation
2
Introduction
Accessories
Preparation
Please check and identify the supplied
accessories.
About the “ ” Symbol Display
“ ” may appear on your TV display during
operation and indicates that the function
explained in this owner’s manual is not
available on that specific media.
FM antenna (1)
AM antenna (1)
HDMI cable (1)
Speaker cables (5)
Analog audio cable
(1)
Composite video
cable (1)
Remote control (1)
Batteries (2)
Symbols Used in this Manual
NOTE
Indicates special notes and operating features.
CAUTION
Indicates cautions for preventing possible
damages from abuse.
A section whose title has one of the following
symbols are applicable only to the disc
represented by the symbol.
MOVIE
Movie files contained in
the USB
MUSIC
Music files contained in
the USB
PHOTO
Photo files contained in
the USB
Preparation
Required cables
• USB cable
The hookup diagrams on the subsequent
pages assume the use of the following
connection cables.
You must purchase the connection cables
separately if necessary.
• Composite video cable
Yellow
• Analog audio/Composite video cable
Yellow (Video)
White (L/audio)
Red (R/audio)
• HDMI cable
2
• Portable cable
NOTE
• Turn off the power to all components before
making any connections.
• When connecting an audio/video cable, be
sure to match the colour-coded pins to the
appropriate jacks on the components: yellow
(video) to yellow; white (left, audio) to white;
and red (right, audio) to red.
• Optical digital audio cable
• When connecting optical digital cables, insert
the cable plugs straight in until they click into
place.
• Do not bend or tie optical digital cables.
• Coaxial digital audio cable
Preparation
• Analog audio cable
White (L)
Red (R)
7
8
Preparation
Remote control
• • • • • • • • • a • • • • • • • • •
POWER (1): Switches the unit ON or OFF.
TV control buttons: Controls the TV. (LG TV
only)
-- 1 : Turns the TV on or off.
-- AV/INPUT : Switches the TV’s input source
between the TV and other input sources.
2
Preparation
INPUT buttons: Selects the input source you
want to use. (Page 25)
-- AV: Selects the input source connected to
AV IN 1/2 jack.
-- PORTABLE: Selects the input source
connected to PORT. IN jack.
-- OPTICAL: Selects the input source
connected to OPTICAL IN 1/2 jack.
-- COAXIAL: Selects the input source
connected to COAXIAL IN 1/2 jack.
-- HDMI IN: Selects the input source
connected to HDMI IN jack.
-- RADIO: Selects the FM/AM.
-- USB: Selects the input source connected to
USB port.
CLEAR: Deletes a preset stations. (Page 28)
REPEAT: Selects a play mode. (Repeat
playback/ Random playback) (Page 32)
Battery Installation
AUTO DJ: Selects the AUTO DJ mode.
(Page 32)
DIMMER: The display window is darken by
half. (Page 35)
SLEEP: Sets the system to turn off
automatically at a specified time. (Page 36)
Remove the battery cover
on the rear of the Remote
Control, and insert two R03
(size AAA) batteries with
and matched correctly.
Preparation
• • • • • • • • • b • • • • • • • • •
• • • • • • • • • d • • • • • • • • •
./> (SKIP): Goes to the next or previous
SETUP: Displays or exits the [SETUP] menu.
chapter / track / file.
m/M (SCAN): Searches backward or
forward.
RETURN (O): Moves backwards in the menu
or exits the setup menu.
INFO/DISPLAY ( ): Displays or exits Onscreen Display. (Page 33, 35)
N(PLAY): Starts playback.
ENTER ( ): Acknowledges menu selection.
X (PAUSE): Pauses playback.
MARKER: Marks music files on the [MUSIC]
menu. (Page 31)
• • • • • • • • • c • • • • • • • • •
PRESET (-/+): Selects a preset stations.
SOUND EFFECT: Selects a sound effect mode.
(Page 26)
VOL (-/+) : Adjusts speaker volume.
TUNING (-/+): Tunes in the desired radio
station.
U/u/I/i (up/ down/ left/ right): Selects an
option in the menu.
MONO/STEREO: Selects mono/stereo in FM
mode. (Page 27)
MUTE ( ): Turns off the sound temporarily.
Press the button again to restore the sound.
• • • • • • • • • e • • • • • • • • •
BASS BLAST: Selects the BASS BLAST sound
mode directly. (Page 27)
MIC VOL (-/+): Adjusts the microphone
volume. (Page 36)
ECHO VOL (-/+): Adjusts the echo volume.
(Page 36)
0 to 9 numerical buttons: Selects numbered
options in a menu.
2
Preparation
x (STOP): Stops playback.
SPEAKER LEVEL: Sets the sound level of
desired speaker. (Page 25)
9
10
Preparation
Front panel
2
Preparation
j k
a STANDBY/ON (1/[)
Switches the unit ON or OFF.
b INPUT SELECTOR
Selects the input source. Rotate this knob
until the input source you want appears in
the display window.
c Display window
Shows the current status of the unit.
d MASTER VOLUME
Adjusts the speaker volume.
e PHONES connector
Connects a stereo headphone plug (
3.5 mm) to PHONES connector for private
listening. (Page 20)
f MULTI CONTROL
Adjusts the various options.
g BASS BLAST
Selects the BASS BLAST sound mode
directly. (Page 27)
h SOUND EFFECT
Selects a sound effect mode. (Page 26)
l
m n
o
p
i USER EQ
Sets the USER EQ mode (BASS, MIDDLE
and TREBLE). (Page 27)
j ENTER
Acknowledges menu selection.
k PLAY/PAUSE
Starts playback.
Pauses playback, press it again to exit
pause status.
Moves to the BASS mode if you press PLAY/
PAUSE on the front panel while the “USER
EQ” is displayed in the display window.
l STOP
Stops playback.
m MIC
Connects a microphone (
MIC jack.
6.3 mm) to
n PORT. IN
Connects a portable device (MP3 player,
etc) to PORT. IN jack.
o AV IN 2 (L-AUDIO-R, VIDEO)
Connects the components with analog
audio/video output jacks (camcorder,
video game, etc).
p USB port (5 V 500 mA)
Connects an USB device to USB port.
Preparation
11
Rear panel
2
Preparation
a
b
a Speakers connectors
Connects the speaker cables.
b OPTICAL IN 1/2
Connects other components with an
optical digital audio output.
c COAXIAL IN 1/2
Connects other components with a coaxial
digital audio output.
d HDMI IN
Connects the component with HDMI
output.
e HDMI OUT
Connects a TV or component with HDMI
input.
c d
e
fg h i
f AV IN 1 (L-AUDIO-R, VIDEO)
Connects the components with analog
audio/video output jacks (DVD player, Bluray disc player, Satellite tuner, Set-top box,
etc).
g AUDIO L/R OUTPUT
Connects the components with analog
audio input jacks.
h Antenna connectors
FM – Connects the FM wired antenna.
AM – Connects the AM loop antenna.
i VIDEO OUT
Connects to your TV or projector with
video input.
12
Installation
3
Installation
Installing speakers
3
Installation
The unit allows you to use 5.2 channel system.
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from the
actual unit for explanation purposes. For the
best possible rear sound, all the speakers other
than the subwoofer should be placed at the
same distance from the listening position (A).
Example of 5.2 channel speaker system
configuration
B
A
C G
F
H
F
A
A
AA
A
D
C Center speaker
Place the center speaker above or below the
monitor or screen.
D Rear speaker (left)/ E Rear speaker
(right)
Place these speakers behind your listening
position, facing slightly inwards.
F/G Subwoofer
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place
the subwoofer near the front speakers. Turn
it slightly toward the center of the room to
reduce the wall reflections.
H Unit
A
A
A Front speaker (left)/ B Front speaker
(right)
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
CAUTION
E
• Be careful that the speaker
should not fall down.
Otherwise it may result in the
speaker malfunctioning and
causing personal injury and/
or property damage.
• Make sure to install the speaker with other
people in order to prevent it from falling and
causing injuries to the installer.
Installation
Connecting speakers
2. Connect the wires to the speakers. Connect
the other end of each wire to the correct
speaker according to the color coding:
Before connecting the cables, be sure to
disconnect the AC power cord.
Speaker system connection
Front speaker (R)
Black
Red
Center speaker
Noir
Red
Front speaker (L)
Noir
Red
Color
Speaker
Position
Green
Center
Center
Orange
Subwoofer
Any front
position
Red
Front
Front right
White
Front
Front left
Grey
Rear
Rear right
Blue
Rear
Rear left
To connect the cable to the speakers,
press each plastic finger pad to open the
connection terminals on the base of each
speaker. Insert the wire and release the
finger pad.
CAUTION
Red
Rear speaker (R)
Subwoofer
Black
Red
Rear speaker (L)
Subwoofer
1. Connect the wires to the unit. To connect
the cable to the unit, press each plastic
finger pad to open the connection terminal.
Insert the wire and release the finger pad.
Connect the black end of each wire to the
terminals marked -(minus) and the other
end to the terminals marked + (plus).
• Be careful to make sure children not to put their
hands or any objects into the *speaker duct.
*Speaker duct: A hall for plentiful bass sound on
speaker cabinet (enclosure).
• Place the centre speaker at a safe distance from
the child’s reach. Otherwise it may result in the
speaker falling down and causing personal
injury and/or property damage.
• The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far away
from either TV screen or PC monitor.
3
Installation
Black
13
14
Installation
Connecting to Your TV
You can watch the selected input image when
you connect the VIDEO OUT or HDMI OUT jack
to a TV.
It is not necessary to connect all the cables.
Connect the cables according to the jacks of
your components.
• Video/Audio (Left/Right) connection
(page 14)
• HDMI connection (page 15)
Video/Audio (Left/Right)
connection
Connect the VIDEO OUT jack on the unit to
the video in jack on the TV using a video cable.
Connect the left and right AUDIO OUT jacks of
the unit to the audio left and right IN jacks on
the TV using the audio cables.
Video/Audio Connection
Unit
3
Installation
NOTE
• Before connecting the cables, be sure to
disconnect the AC power cord.
• Turn off the power to all components before
making any connections.
• When connecting an audio/video cable, be
sure to match the colour-coded pins to the
appropriate jacks on the components: yellow
(video) to yellow; white (left, audio) to white;
and red (right, audio) to red.
Audio cable
TV
Video
cable
Set the TV’s source to VIDEO (refer to TV’s
Owner’s manual).
Installation
HDMI connection
If you have a HDMI TV or monitor, you can
connect it to this unit using a HDMI cable.
Connect the HDMI OUT jack on the unit to
the HDMI IN jack on a HDMI compatible TV or
monitor.
HDMI Connection
NOTE
• HDMI is the abbreviated name for High
Definition Multimedia Interface. It is an interface
which transmits video and audio signals in
digital format. If a connected HDMI device does
not accept the audio output of the unit, the
HDMI device’s audio sound may be distorted or
may not output.
• When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 16.)
Unit
TV
Set the TV’s source to HDMI (refer to TV’s
Owner’s manual).
• When you connect a HDMI or DVI compatible
device make sure of the following:
-- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
-- The connected device’s video input is set
correctly for this unit.
-- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1 280 x 720p, 1 920 x 1 080i or 1 920 x 1 080p
video input.
• Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
-- The picture will not be displayed properly
with non-HDCP device.
-- This unit does not playback and TV screen is
changed to black screen.
• If there is noise or lines on the screen, please
check the HDMI cable and use a higher version
cable than 1.2A HDMI cable.
• Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off the
player and then turn it on again.
• When the HDMI connection with HDCP is not
verified, TV screen is changed to black screen.
In this case, check the HDMI connection, or
disconnect the HDMI cable.
3
Installation
HDMI
Cable
15
16
Installation
Resolution Setting
The unit provides several output resolutions for
HDMI OUT jack. You can change the resolution
using [Setup] menu.
1. Press SETUP.
The [Setup] menu appears.
Connecting TV or
components with
HDMI jack
1. Connect the HDMI OUT jack on the unit to
the HDMI IN jack on a HDMI compatible TV
or monitor. Connect the HDMI IN jack on
the unit to your components with HDMI
OUT jack using a HDMI cable.
3
Installation
HDMI Connection
2. Use U/u to select [Display] option then
press i to move to the second level.
3. Use U/u to select the [Resolution] option
then press i to move to the third level.
Unit
HDMI cable
HDMI cable
TV, Monitor, etc
4. Use U/u to select the desired resolution
then press ENTER ( ) to confirm your
selection.
NOTE
If your TV does not accept the resolution you have
set on the player, you can set resolution to 480p (or
576p) as follows:
Press x (STOP) for more than 5 seconds.
Blu-ray disc player,
DVD player, etc
2. Set the input source to HDMI (Page 24).
Installation
Connecting components
with analog video and
audio jacks
It is not necessary to connect all the cables.
Connect the cables according to the jacks
of your components. Before connecting the
cables, be sure to disconnect the AC power
cord.
AV IN 2 connection
1. Connect the VIDEO IN jack on the unit to
the VIDEO OUT jack on your component
using a video cable. Connect the left and
right AUDIO IN jacks of the unit to the audio
left and right OUT jacks on your component
using the audio cables.
Analog Video/Audio Connection
Unit
3
Analog Video/Audio Connection
Installation
AV IN 1 connection
1. Connect the VIDEO IN jack on the unit to
the VIDEO OUT jack on your component
using a video cable. Connect the left and
right AUDIO IN jacks of the unit to the audio
left and right OUT jacks on your component
using the audio cables.
Audio cable
Video
cable
Unit
Audio cable
Video
cable
Blu-ray disc player,
DVD player, etc
Camcorder, video
game, etc
2. Connect the unit to your TV. Refer the
“Video/Audio (Left/Right) connection” on
the page 14.
3. Set the input source to AV 1 (Page 24).
17
2. Connect the unit to your TV. Refer the
“Video/Audio (Left/Right) connection” on
the page 14.
3. Set the input source to AV 2 (Page 24).
18
Installation
Connecting
components with
Digital Audio jacks
Coaxial digital audio
connection
1. Connect the COAXIAL IN 1/2 jack on the
unit to your components with COAXIAL
OUT jack using a coaxial digital audio cable.
COAXIAL IN connection
It is not necessary to connect all the cables.
Connect the cables according to the jacks
of your components. Before connecting the
cables, be sure to disconnect the AC power
cord.
3
Unit
Installation
Optical digital audio
connection
1. Connect the OPTICAL IN 1/2 jack on the
unit to your components with OPTICAL
OUT jack using an optical digital audio
cable.
Blu-ray disc player,
DVD player, etc
OPTICAL IN connection
Unit
2. Set the input source to COAXIAL 1/
COAXIAL 2 (Page 24).
Blu-ray disc player,
DVD player, etc
2. Set the input source to OPTICAL 1/ OPTICAL
2 (Page 24).
Installation
Connecting the
portable device
1. Connect the PORT. IN jack on the unit to the
LINE OUT jack on your Portable device (MP3
player, etc...) using a portable cable ( 3.5
mm).
Portable device connection
Connecting the
antennas
Connect the supplied AM loop antenna and
FM wire antenna.
Before connecting the antenna, be sure to
disconnect the AC power cord.
Antennas connection
3
Unit
AM loop antenna
Unit
NOTE
• To prevent noise pickup, keep the AM Loop
antenna away from the unit and other
components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as
horizontal as possible.
2. Set the input source to PORTABLE (Page 24).
Installation
FM wire antenna
Portable device
(MP3 player, etc...)
19
20
Installation
Connecting the
headphones
Connect a pair of stereo headphones ( 3.5
mm phone plug) to the unit’s PHONES jack for
private listening.
Headphones connection
Unit
3
Installation
Headphones
NOTE
• Always turn down the volume before
connecting your headphones.
• The speakers are turned off while the
headphones plug is inserted in the PHONES
jack.
Installation
Settings
Adjusting the Setup Settings
You can change the settings of the unit in the
[Setup] menu.
1. Press SETUP.
The [Setup] menu appears.
21
[Language] Menu
Menu Language
Select a language for the [Setup] menu and
on-screen display.
[Display] Menu
TV Aspect
Select which screen aspect to use based on
the shape of your TV screen.
2. Use U/u to select the first setup option, and
press i to move to the second level.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the
TV Aspect mode is set to 4:3.
3. Use U/u to select a second setup option,
and press ENTER ( ) to move to the third
level.
[Letterbox]
Displays a wide picture with bands on the
upper and lower portions of the screen.
[Panscan]
Automatically displays the wide picture on
the entire screen and cuts off the portions
that do not fit.
Resolution
Sets the output resolution of the HDMI video
signal. Refer to “Resolution Setting” for details
about the resolution (page 16).
4. Use U/u to select a desired setting, and
press ENTER ( ) to confirm your selection.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best
suited to the connected TV.
Installation
[4:3]
Select when a standard 4:3 TV is connected.
3
22
Installation
[576i]
Outputs 576 lines of interlaced video.
[576p]
Outputs 576 lines of progressive video.
[720p]
Outputs 720 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
[1080p]
Outputs 1080 lines of progressive video.
3
Installation
[Audio] Menu
Speaker Setup
Make the following settings for the built-in 5.2
channel surround decoder.
1. Select [Speaker Setup] on the [Audio]
menu.
2. Press ENTER ( )
The [SPEAKER] menu appears.
3. Use I/i to select the desired speaker.
4. Adjust options using U/u/I/i buttons.
5. After adjusting the desired options, press
RETURN (O). The menu moves to the
previous screen.
[Speaker]
Select a speaker that you want to adjust.
NOTE
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
[Size]
Since the speaker settings are fixed, you
cannot change the settings.
[Volume]
Press I/i to adjust the output level of the
selected speaker.
- Front L/R : 0 ~ -5
- SubWoofer, Rear L/R, Center : 5 ~ -5
[Distance]
After you connected speakers to your unit,
set the Distance between the speakers and
your listening point if the distance of Center
or Rear speakers is bigger than the distance
of Front speakers. This allows the sound
from each speaker to reach the listener
at the same time. Press I/i to adjust the
Distance of the selected speaker. This
distance is equivalent to a difference of the
distance between Center or Rear speaker
and Front speakers.
[Speaker Test Start]/ [Speaker Test Stop]
Select [Speaker Test Start] by using the U/
u and press ENTER ( ). Press ENTER ( )
again to stop. Adjust the volume to match
the volume of test signals memorized in the
system.
Installation
DRC (Dynamic Range Control)
When a title encoded in Dolby Digital or Dolby
Digital Plus is playing back, you may wish to
compress the dynamic range of the audio
output (the difference between the loudest
sounds and the quietest ones). This allows you
to listen to a movie at a lower volume without
losing clarity of sound. Set [DRC] to [On] for
this effect.
HD AV Sync
sec.
NOTE
This function is only operated on the USB mode.
[Others] Menu
DivX(R) VOD
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official
DivX Certified device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play DivX Video-on-Demand (VOD) content.
To generate the registration code, locate the
DivX VOD section in the device setup menu.
Go to vod.divx.com with this code to complete
the registration process and learn more about
DivX VOD.
[Register]
Displays the registration code of your unit.
[Deregister]
Deactivate your unit and display the
deactivation code.
NOTE
All the downloaded videos from DivX VOD with
this player’s registration code can only be played
back on this unit.
3
Installation
Sometimes Digital TV encounters a delay
between picture and sound. If this happens
you can compensate by setting a delay on the
sound so that it effectively ‘waits’ for the picture
to arrive: this is called HD AV Sync. Use U/u
(on the remote control) to scroll up and down
through the delay amount, which you can set
at anything between 0 and 300m .
23
24
Operation
4
Operation
Turning On the unit
4
Operation
To select the
Display
Component connected to
AV IN 1 jack
AV 1
Before connecting the power cord, connect all
your speakers and AV components.
Component connected to
AV IN 2 jack
AV 2
1. Plug the power cord into an AC wall outlet.
Portable device connected
to PORT. IN jack
PORTABLE
Component connected to
OPTICAL IN 1 jack
OPTICAL 1
Component connected to
OPTICAL IN 2 jack
OPTICAL 2
Component connected to
COAXIAL IN 1 jack
COAXIAL 1
Component connected to
COAXIAL IN 2 jack
COAXIAL 2
Component connected to
HDMI jack
HDMI IN
Built-in tuner
Tuner or
frequency
USB device connected to
USB port
USB
2. Press the POWER (1 or 1/[) button.
The unit turns on, the display window lights
up.
To turn off the unit, press the POWER (1 or
1/[) button.
Selecting the input
source
This section explains how to select the input
source (i.e., the AV component that you want
to listen to or watch).
1. Press POWER (1 or 1/[) to turn the unit
on.
2. Select a source by rotating the INPUT
SELECTOR on the front panel.
The selected source appears in the display
window.
Operation
To select the required input source using
the remote control, use the INPUT buttons.
To select the
Button
Component connected to
AV IN 1/2 jack
AV
Portable device connected
to PORT. IN jack
PORTABLE
Component connected to
OPTICAL IN 1/2 jack
OPTICAL
Component connected to
COAXIAL IN 1/2 jack
COAXIAL
Component connected to
HDMI jack
HDMI IN
Built-in tuner
RADIO
USB device connected to
USB port
USB
Adjusting the speaker
levels
You can adjust the level of each speaker. These
settings are applied to all sound fields. You can
adjust from -5 to +5 in 1 step.
1. Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
The indicator changes cyclically in the
display window as follows.
SW t FL t C t FR t RR t RL
2. Press VOL (-/+) to adjust the sound level of
the selected speaker while the indicator is
displayed in the display window.
Description
SW
Subwoofer (-5 to +5)
3. Turn on the component and start playback.
FL
Front speaker (left) (-5 to 0)
4. To adjust the volume, rotate the MASTER
VOLUME on the front panel, or press VOL
(-/+) on remote control.
C
Center speaker (-5 to +5)
FR
Front speaker (right) (-5 to
0)
To activate the muting function
RR
Rear speaker (right) (-5 to
+5)
RL
Rear speaker (left) (-5 to +5)
3. Repeat and adjust the sound level of the
other speakers.
4
Operation
Display
Press MUTE ( ) on the remote control. To
cancel, press MUTE ( ) on the remote control
again or rotate the MASTER VOLUME on the
front panel.
25
26
Operation
Enjoying various
sound mode
You can enjoy various sound mode. For details,
refer to the Sound Effect, Bass Blast, and USER
EQ. (Pages 26-27)
Sound Effect
BASS BLAST
During playback, reinforces
the bass sound.
LOUDNESS
Improves the bass and
treble sound.
VIRTUAL
You can enjoy more virtual
surround sound.
PL MOVIE
PL MUSIC
Dolby Pro Logic II enables
you to play stereo source
on 5.2-channel.
BYPASS
You can enjoy the 2 channel
sound from front speakers
and subwoofer.
You can select a suitable sound mode. Press
SOUND EFFECT repeatedly until the desired
mode appears in the display window.
Display
Description
NAT PLUS
You can enjoy the natural
sound effect same as a
5.2-channel.
NATURAL
You can enjoy comfortable
and natural sound.
Local
specialization
equalizer
Regionally optimized
sound effect. (DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/
SAMBA/ SALSA/ CUMBIA/
AFRO)
AUTO EQ
Sets the sound equalizer to
the mode that is the most
similar to the genre which
is included in the MP3 ID3
tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
MP3-OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
4
NOTE
Operation
• In some of surround modes, some speakers,
there’s no sound or low sound. It depends on
the mode of surround and the source of audio,
it is not defective.
• You may need to reset the surround mode, after
switching the input, sometimes even after the
sound track changed.
• This function is not operated when the
microphone is connected to the unit.
Operation
Bass Blast
You can set the BASS BLAST sound mode
directly.
27
Listening to FM/AM
radio
Press BASS BLAST repeatedly.
Display
Description
BASS BLAST
During playback, reinforces
the bass sound.
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
antennas to the unit. (Page 19)
BYPASS
You can enjoy the 2 channel
sound from front speakers
and subwoofer.
Automatic tuning
NOTE
This function is not operated when the
microphone is connected to the unit.
You can listen to music with desired sound
effect by adjusting the BASS, MIDDLE and
TREBLE.
1. Press USER EQ on the front panel.
“USER EQ” appears in the display window.
2. Press PLAY/PAUSE on the front panel while
the “USER EQ” is displayed in the display
window.
3. Select the BASS, MIDDLE or TREBLE by
pressing ENTER on the front panel.
4. Rotate MULTI CONTROL on the front panel
to set sound level.
5. Press PLAY/PAUSE on the front panel to
finish the settings.
NOTE
This function is not operated when the
microphone is connected to the unit.
2. Press TUNING - or TUNING + for more than
2 seconds.
Press TUNING - for more than 2 seconds to
scan from high to low.
Press TUNING + for more than 2 seconds to
scan from low to high.
The unit stops scanning whenever a station
is received.
In case of poor FM stereo reception
If the FM stereo reception is poor and “ST.”
flashes in the display window, select monaural
audio so that the sound will be less distorted
by pressing the MONO/STEREO.
The “ST.” indicator disappears in the display
window. There will be no stereo effect, but the
reception will improve. Press the button again
to restore the stereo effect.
Manual tuning
Press TUNING - or TUNING + briefly and
repeatedly on the FM or AM mode to select a
station you want. Or rotate MULTI CONTROL on
the unit.
4
Operation
Setting the USER EQ
1. Rotate INPUT SELECTOR to select tuner (FM
or AM). Or press RADIO with the remote
control to select tuner (FM or AM).
28
Operation
Presetting radio stations
Tuning to preset stations
You can preset up to 50 FM or AM stations.
Then you can easily tune in the stations you
often listen to.
Before tuning to preset stations, make sure you
preset radio stations. (Page 28)
1. Rotate INPUT SELECTOR to select tuner (FM
or AM). Or press RADIO with the remote
control to select tuner (FM or AM).
2. Tune in the station that you want to preset
using Automatic tuning or Manual tuning.
3. Press ENTER ( ).
A preset number flashes in the display
window for a few seconds. When a preset
number flashes, do the step 4.
4
4. Press PRESET - or PRESET+ to select a preset
number you want.
If a preset number is not flashed before you
select the preset number, start again from
the step 3.
Operation
5. Press ENTER ( ) again.
The station is stored to the selected preset
number. If a preset number is not flashed
before you press ENTER ( ), start again
from the step 3.
6. Repeat the steps 2 to 5 to preset another
station.
1. Rotate INPUT SELECTOR to select tuner (FM
or AM). Or press RADIO with the remote
control to select tuner (FM or AM).
2. Press PRESET - or PRESET+ repeatedly to
select the preset station you want.
Each time you press the button, you can
select a preset station.
Deleting the preset stations
You can delete a preset station you want.
1. Rotate INPUT SELECTOR to select tuner (FM
or AM). Or press RADIO with the remote
control to select tuner (FM or AM).
2. Select the preset station to delete by
pressing PRESET - or PRESET+.
3. Press CLEAR.
4. Press CLEAR again while the preset number
flashes in the display window for a few
seconds.
The preset station is deleted.
5. Repeat the steps 2 to 4 to delete another
preset station.
Deleting all the preset stations
1. Press and hold CLEAR for about two
seconds.
“ERASE ALL” appears in the display window.
2. Press CLEAR again while “ERASE ALL” is
displayed.
All the preset stations are cleared.
Operation
Playing the USB
device
29
3. Select [Music], [Movie] or [Photo] using I/
i, and press ENTER ( ) to play the file.
To stop playback
MUSIC MOVIE PHOTO
This unit can play movie, music and photo files
contained in the USB device.
Basic operations
1. Insert an USB device to the USB port until it
fits into place.
USB device connection
Unit
To pause playback
MUSIC MOVIE
Press X (PAUSE) during playback.
Press B (PLAY) to resume playback.
To scan forward or backward
MUSIC MOVIE
2. Rotate INPUT SELECTOR on the front
panel to select until the “USB” appears in
the display window. Or press USB on the
remote control.
When you connect the USB device
contained music files only in the USB device,
the unit plays music files automatically. If
the USB device is containing various types
of files, the [USB] menu for the file type
selection will appear.
[USB] menu
To skip to the next/previous chapter/
track/file
MUSIC MOVIE
During playback, press . or > to go to
the next chapter/track/file or to return to the
beginning of the current chapter/track/file.
Press . twice briefly to step back to the
previous chapter/track/file.
PHOTO
During playback, press . or > to go to
the previous/next file.
4
Operation
Press m or M to play fast forward or fast
reverse during playback.
You can change the various playback speeds
by pressing m or M repeatedly.
Press B (PLAY) to return to normal speed.
USB device
Press x (STOP) during playback.
30
Operation
To slow down the playing speed
MOVIE
While the playback is paused, press M
repeatedly to play various speeds of slow
motion.
Resume playback
MUSIC MOVIE
The unit records the point where you pressed
the x (STOP) depending on the file.
If “Xx (Resume Stop)” appears on the screen
briefly, press B (PLAY) to resume playback
(from the scene point).
If you press x (STOP) twice, “x (Complete
Stop)” appears on the screen. The unit will clear
the stopped point.
4
Operation
Removing the USB device from the
unit
NOTE
• Devices which require additional program
installation connected to a computer, are not
supported.
• Do not extract the USB device while in
operation.
• For a large capacity USB, it may take longer than
a few minute to be searched.
• Regular back up is recommended to prevent
data loss.
• If you use a USB extension cable or USB hub, the
USB device is not recognized.
• Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
• This unit is not supported when the total
number of files is 1 000 or more.
• External HDD, Card readers, Locked devices, or
hard type usb devices are not supported.
• USB Port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
1. Choose a different function mode or press
x (STOP) twice in a row.
• USB device: USB device that supports USB 1.1
and USB 2.0.
2. Remove the USB device from the unit.
• Digital camera and mobile phone are not
supported.
Compatible USB Devices
-- MP3 Player : Flash type MP3 player.
-- USB Flash Drive : Devices that support USB
2.0 or USB 1.1.
-- Some USB device may not work with this
unit.
Operation
Listening to music
You can play music files contained in a USB
device.
1. Select [Music] using I/i on the [USB]
menu.
31
NOTE
• The file requirements are described on page 32.
• You can use various playback functions. Refer to
pages 29-30.
2. Press ENTER ( ).
The unit plays music files automatically.
Playing your favorite music
Using the [MUSIC] menu
This enables you to play the marked music in
order by marking your favorite files.
1. During playback, select your favorite files
using U/u.
[MUSIC] menu
2. Press MARKER.
The s indicator appears on the [MUSIC]
menu.
3. Repeat steps 1-2.
Buttons
Select All
Select a
desired
option
using U/u/
I/i.
Deselect
All
Moving to the
previous or next
page.
Marking all the
files.
Deselecting all
the marked files.
s Mark
MARKER
Marking the
selected files.
bBvV
Move
U/u/I/i
Moving to
another file.
ENTER ( )
Activating a file.
Select
Mark Play
Returning to the
upper folder.
UP
FOLDER
m/M
Description
O Close RETURN
(O)
Returning to
the [USB]
menu.
Current Play
5. Select the desired play mode using U/u.
[Mark Play]: Plays the marked files in order.
[Current Play]: Plays the files in order from
the highlighted position.
6. Press ENTER ( ).
NOTE
• If you want to delete a marker, select the marked
file and then press MARKER.
• The markers are also cleared when the USB
device is removed, the unit is switched to power
off or the function is switched to others.
4
Operation
Options
4. Press B (PLAY) or ENTER ( ).
The play mode is displayed on the [MUSIC]
menu.
32
Operation
Playing repeatedly or randomly
Music file requirement
During playback, press
REPEAT repeatedly
to select a desired mode.
Music file compatibility with this unit is limited
as follows :
Display
Description
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
REPEAT
The current file will be
played repeatedly.
• Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
REPEAT ALL
All the files will be played
repeatedly.
• Support Version : v2, v7, v8, v9
RANDOM
The files will be played in
random order.
• File extensions : “.mp3”/ “.wma”
Returns to normal playback.
• We recommend that you use Easy-CD
Creator, which creates an ISO 9660 file
system.
Off
(No display)
AUTO DJ playback
4
AUTO DJ blends the end of one song into the
beginning of another for seamless playback.
Operation
During playback, press AUTO DJ repeatedly to
select a desired mode.
• Maximum files : Under 999
• CD-ROM file format : ISO 9660/ JOLIET
Playing a movie file
You can play movie files contained in a USB
device.
1. Select [Movie] using I/i on the [USB]
menu.
Display
Description
AUTO DJ
RANDOM
The music is played
randomly on this mode.
AUTO DJ
SEQUENTIAL
The music is played
repeatedly on this mode.
Displaying content information onscreen
AUTO DJ OFF
Returns to normal playback.
You can display and adjust various information
and settings about the content.
2. Select a file using U/u/I/i, and press B
(PLAY) or ENTER ( ) to play the file.
1. During playback, press INFO/DISPLAY ( ) to
show various playback information.
a
b
c
d
e
Operation
a Title – current title number/total number
of titles
b Time – elapsed playing time/total
playback time
Hearing different audio
1. During playback, press INFO/DISPLAY ( ) to
display the On-Screen display.
2. Use U/u to select the [Audio] option.
c Audio – selected audio language or
channel
3. Use I/i to select desired audio language,
audio track or audio channel.
d Subtitle – selected subtitle
e Code Page – selected subtitle code page
Selecting a subtitle language
2. Select an option using U/u.
1. During playback, press INFO/DISPLAY ( ) to
display the On-Screen display.
3. Use I/i to adjust the selected option
value.
2. Use U/u to select the [Subtitle] option.
4. Press INFO/DISPLAY ( ) or RETURN (O) to
exit the On-Screen display.
NOTE
Playing from selected time
1. Press INFO/DISPLAY ( ) during playback.
The time search box shows the elapsed
playing time.
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds, enter “21020”.
3. Press ENTER ( ) to start playback from
selected time.
3. Use I/i to select desired subtitle language.
4. Press RETURN (O) to exit the On-Screen
display.
Changing subtitle code page
If the subtitle is not displayed properly, you
can change the subtitle code page to view the
subtitle file properly.
1. During playback, press INFO/DISPLAY ( ) to
display the On-Screen display.
2. Use U/u to select the [Code Page] option.
3. Use I/i to select desired code option.
4. Press RETURN (O) to exit the On-Screen
display.
4
Operation
If no button is pressed for a few seconds, the onscreen display disappears.
33
34
Operation
Movie file requirement
Movie file compatibility with this unit is limited
as follows :
• Available resolution: within 720 x 576
(W x H) pixels.
• The file name of the DivX subtitle should be
entered within 45 characters.
• If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on
the display.
Viewing a photo
You can view photo files contained in a USB
device.
1. Select [Photo] using I/i on the [USB]
menu.
The [PHOTO] menu appears.
[PHOTO] menu
• Frame rate : less than 30 fps.
• If the video and audio structure of recorded
files is not interleaved, either video or audio
is outputted.
• Playable movie file : “.avi”, “.mpg”, “.mpeg”,
“.divx”
4
Operation
• Playable Subtitle format : SubRip (*.srt/
*.txt), SAMI (*.smi), SubStation Alpha (*.ssa/
*.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0
(*.sub/ *.txt), Vobsub (*.sub)
Options
Buttons
Description
UP
FOLDER
Select a
desired
option
using U/u/
I/i.
Returning to the
upper folder.
B Slide
Show
B (PLAY)
Viewing a slide
show.
bBvV
Move
U/u/I/i
Moving to
another file or
content.
ENTER ( )
Viewing a
particular file.
m/M
• Playable Codec format : “DIVX3.xx”,
“DIVX4. xx”, “DIVX5.xx”, “MP4V3”, “3IVX”.
• Playable Audio format : “AC3”, “DTS”, “PCM”,
“MP3”, “WMA”.
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
• Bit rate : within 32 to 320 kbps (MP3), 40 to
192 kbps (WMA)
•
For Discs formatted in Live file system, you
can not it on this unit.
• If the name of movie file is different from
that of the subtitle file, during playback of a
DivX file, subtitle may not be display.
• If you play a DivX file differ from DivXspec, it
may not operate normally.
Select
O Close RETURN
(O)
Moving to the
previous or next
page.
Returning to the
[USB] menu.
2. Select a file using U/u/I/i, and press B
(PLAY) or ENTER ( ) to play the file.
Options
Buttons
Description
B Slide
Show
B (PLAY)
Viewing a slide
show.
ENTER ( )
Viewing a
particular file.
Select
Operation
To stop a slide show
Photo file requirement
Press x (STOP) during slide show.
Photo file compatibility with this unit is limited
as follows :
To pause a slide show
• Max pixel in width : 2 760 x 2 048 pixel
Press X (PAUSE) during slide show.
Press B (PLAY) or X (PAUSE) to re-start the
slide show.
• Maximum files : Under 999
To skip to the next/previous photo
• File extensions: “.jpg”
While viewing a photo in full screen, press I or
i to go to the previous or next photo.
• CD-ROM file format : ISO 9660/ JOLIET
35
• Some files may not operate due to a
different recording format or the condition
of file.
Dimmer
Options while viewing a photo
You can use various options while viewing a
photo in full screen.
1. While viewing a photo in full screen, press
INFO/DISPLAY ( ) to display the option
menu.
Press DIMMER once. The display window will
be darken by half. To cancel it, press DIMMER
again.
Screen Saver
The screen saver appears when you leave the
unit in Stop mode for about five minutes.
a
b
c
d
e
a Current photo/Total number of photos
– Use I/i to view previous/next photo.
b Slide Show – Press ENTER ( ) to start or
pause slide show.
c Speed – Use ENTER ( ) to select a delay
time between photos in a slide show.
d Rotate – Press ENTER ( ) to rotate the
photo clockwise/counterclockwise.
e Go to list– Press ENTER ( ) to return
[Photo] menu.
3. Press RETURN (O) or INFO/DISPLAY ( ) to
exit the option menu.
Operation
2. Select an option using U/u/I/i.
4
36
Operation
Using the Sleep Timer
Using microphone
You can set the unit to turn off automatically at
a specified time.
Press SLEEP repeatedly.
The indicator changes cyclically in the display
window as follows.
SLEEP 180 t 150 t 120 t 90 t 80 t 70
t 60 t 50 t 40 t 30 t 20 t 10 t
Off (No display)
1. Connect a microphone (
jack.
6.3 mm) to MIC
Microphone connection
Unit
To check the remaining time, press SLEEP. The
remaining time appears in the display window.
Operation
NOTE
When the sleep timer is activated, the display
window dims.
ON
4
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then
press SLEEP once again while “SLEEP 10” is
displayed.
Microphone
“ “ is displayed in the display window.
2. Play the music you want.
3. Sing along with the accompaniment.
4. Adjust the microphone volume by pressing
MIC VOL (-/+).
5. Adjust the echo volume by pressing ECHO
VOL (-/+).
NOTE
• When not using the microphone, set the
microphone volume to minimum or turn off the
microphone and remove the microphone from
the MIC jack.
• If the microphone is set too near the speaker, a
howling sound may be produced. In this case,
move the microphone away from the speaker
or decrease the sound level by using the MIC
VOL(+/-) button.
• The microphone function is not operated in
the digital (COAXIAL 1 , COAXIAL 2, OPTICAL 1,
OPTICAL 2 or HDMI IN) mode.
Maintenance
37
5
Maintenance
Handling the Unit
When shipping the unit
Cleaning the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
To clean the player, use a soft, dry cloth. If
the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as
alcohol, benzine, or thinner, as these might
damage the surface of the unit.
Keeping the exterior surfaces clean
• Do not use volatile liquids such as
insecticide spray near the unit.
• Wiping with strong pressure may damage
the surface.
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service centre.
5
Maintenance
• Do not leave rubber or plastic products in
contact with the unit for a long period of
time.
Maintaining the Unit
38
Troubleshooting
6
Troubleshooting
Troubleshooting
PROBLEM
CAUSE
CORRECTION
No power.
• The power cord is
disconnected.
• Plug the power cord into the wall
outlet securely.
No sound.
• The speaker wires are
disconnected.
• Check the speaker connections.
• The MASTER VOLUME is
adjusted too low.
• Adjust the MASTER VOLUME.
• The MUTE button is pressed
to ON.
• Press the MUTE button to cancel
the muting effect.
• The selected decoding
mode is not matched to the
input signal format.
• Select the available decoding
mode.
• Incorrect selection of input
source.
• Select the desired input source
correctly.
• Incorrect connections
between the components.
• Make connections correctly.
6
Troubleshooting
Radio stations can’t
be tuned in properly.
• The antenna is positioned or • Check the antenna connection
connected poorly.
and adjust its position.
• The signal strength of the
radio station is too weak.
• Tune to the station manually.
• No stations have been
preset or preset stations
have been cleared (when
tuning by scanning preset
channels).
• Preset some radio stations, see
page 28 for details.
Troubleshooting
Preset stations cannot • An incorrect station
be received.
frequency has been
memorized.
Poor FM reception.
The remote control
doesn’t work well / at
all.
39
• Memorize the correct station
frequency.
• The memorized stations are
cleared.
• Memorize the stations again.
• No antenna is connected.
• Connect the antenna.
• The antenna is not
positioned for the best
reception.
• Change the position of the
antenna.
• The remote control is not
pointed directly at the unit.
• Point the remote directly at the
unit.
• The remote control is too far • Use the remote within 23 feet
from the unit.
(7m) of the unit.
• There is an obstacle in the
path between the remote
control and the unit.
• Remove the obstacle.
• The battery in the remote
control are flat.
• Replace the batteries with new
ones.
6
Troubleshooting
40
Appendix
7
Appendix
Trademarks and Licenses
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.
DivX®, DivX Certified® and associated logos are
registered trademarks of DivX, Inc. and are used
under license.”
7
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under licence under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 &
other U.S. and worldwide patents issued & pending.
DTS and the Symbol are registered trademarks & DTS
Digital Surround and the DTS logos are trademarks
of DTS, Inc. Product includes software. © DTS, Inc. All
Rights Reserved.
Appendix
Appendix
41
Specifications
General
• Power requirements: Refer to main label.
• Power consumption: Refer to main label.
• Dimensions (W x H x D): 430 x 150 x 312 mm
• Net Weight (Approx.): 4.1 kg
• Operating temperature:
41 °F to 95 °F (5 °C to 35 °C)
• FM Tuning Range:
87.50 to 108.00 MHz or 87.5 to 108.0 MHz
• AM Tuning Range:
522 to 1 620 kHz or 530 to 1 720 kHz
Amplifier
• Stereo mode: 100 W + 100 W (4 Ω at 1 kHz)
• Operating humidity: 5 % to 90 %
• Bus Power supply (USB): DC 5 V
Tuner
500 mA
Inputs/ Outputs
• AUDIO OUT:
2.0 Vrms (1 kHz, 0 dB), 600 Ω,
RCA jack (L, R) x 1
• Surround mode:
Front: 100 W + 100 W (4 Ω at 1 kHz)
Center: 100 W (4 Ω at 1 kHz)
Rear: 100 W + 100 W (4 Ω at 1 kHz)
Subwoofer: 150 W + 150 W (3 Ω at 1 kHz)
• VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
• HDMI IN/OUT (video/audio):
19 pin (HDMI standard, Type A), HDMI
version 1.2A
• OPTICAL IN 1/2: 3 V (p-p), Optical jack x 2
• COAXIAL IN 1/2: 3 V (p-p), Coaxial jack x 2
• ANALOG AUDIO IN (AV1/AV2):
2.0 Vrms (1 kHz, 0 dB), 600 Ω,
RCA jack (L, R) x 2
• ANALOG VIDEO IN (AV1/AV2):
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 2
• PORT. IN: 0.5 Vrms ( 3.5 mm stereo jack)
7
Appendix
42
Appendix
Speakers
• Front speaker
• Subwoofer
Type: 1 Way 1 speaker
Type: 2 Way 2 speaker
Impedance: 3 Ω
Impedance: 4 Ω
Rated Input Power: 150 W
Rated Input Power: 100 W
Max. Input power: 300 W
Max. Input power: 200 W
Net Dimensions (W x H x D):
275 x 377 x 319 mm
Net Dimensions (W x H x D):
230 x 905 x 335 mm
Net Weight: 6.8 kg
Net Weight: 13.8 kg
• Rear speaker
Type: 2 Way 2 speaker
Impedance: 4 Ω
Rated Input Power: 100 W
Max. Input power: 200 W
Net Dimensions (W x H x D):
175 x 453 x 249 mm
Net Weight: 3.4 kg
• Center speaker
Type: 2 Way 3 speaker
Impedance: 4 Ω
Rated Input Power: 100 W
Max. Input power: 200 W
Net Dimensions (W x H x D):
515 x 175 x 254 mm
Net Weight: 5.0 kg
7
Designs and specifications are subject to change without prior notice.
Appendix
Appendix
43
7
Appendix
Download PDF

advertising