LG | Laptop LM50 | User's Manual | LG Laptop LM50 User's Manual

Service Manual
(LM40/50)
LG Electronics
0
Contents
Ch 1. Service information
Ch 2. Locations
Ch 3. System information
· Specification
· Model configuration
· System Block Diagram
· Fn key combinations
· Status indicators
· BIOS Flash
· BIOS Setup
Ch 4. Symptom-to-part index
· Power system checkout
· Numeric error codes
· Error messages
· LCD-related symptoms
· Indeterminate problems
Ch 5. Removing and replacing a part (FRU)
Ch 6. Part list
· Part list
· Exploded view
1
Ch1. Service information
Chapter 1. Service information
1-1. Important service information
„ Strategy for replacing parts (FRU-Field Replaceable Units)
Before replacing parts
Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this
Use the following strategy to prevent unnecessary expense for replacing and servicing parts
1. If you are instructed to replacing a part but the replacement does not correct the problem, reinstall the
original part before you continue.
2. Some computers have both a processor board and system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
3. If an adapter or device consists of more than one part, any of the parts (FRUs) may be the cause of the
error. Before replacing the adapter or device, remove the parts (FRUs), one by one, to see if the
symptoms change. Replace only the part that changed the symptoms.
Caution
The BIOS configuration on the computer you are servicing may have been customized.
Running Automatic Configuration my alter the settings. Note the current configuration settings;
then, when service has been completed, verify that those settings remain in effect.
„ Strategy for replacing a hard-disk drive
You have to get a User’s approval before formatting or replacing a hard-disk drive. You must let the User
know that the user is responsible for the loss data
Caution
The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an
incorrect drive, data or programs can be overwritten.
2
Ch1. Service information
1-2. Safety notices
Warning
Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs,
and other small parts are in place and are not left loose inside the computer. Verify this by
shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause
electrical shorts.
Warning
some standby batteries contain a small amount of nickel and cadmium. Do not disassemble
a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery
as required by local ordinances or regulations. Use only the battery in the appropriate parts
listing. Use of an incorrect battery can result in ignition or explosion of the battery
Warning
The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or
water, or short-circuit it. Dispose of the battery pack as required by local ordinances or
regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Use of an incorrect battery can result in ignition or explosion of the battery.
Warning
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands,
immediately was the affected areas with water for at least 15 minutes. Seek medical care if any
symptoms from the fluid are present after washing.
Warning
To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.
Warning
Though the main batteries have low voltage, a shorted or grounded battery can produce enough
current to burn personnel or combustible materials.
Warning
Before removing any part (FRU), turn off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
3
Ch1. Service information
1-3. Safety information
„ General safety
Follow these rules to ensure general safety
· Observe good housekeeping in the area of the machines during and after maintenance.
· When lifting any heavy object
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles
(This action removes the strain from the muscles in your back.)
· Do not attempt to lift any object weights more then 16kg(35lb) or object that you think are too heavy for you.
· Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
· Before you start the machine, ensure that other service representatives and the customer’s personnel are
not in a hazardous position.
· Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
· Keep your tool box away from walk areas so that other people will not trip over it.
· Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
· Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately
8 centimeters(3 inches) from the end.
· Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for you clothing.
· Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
· After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
· Reinstall all covers correctly before returning the machine to the customer.
Caution
Metal objects are good electrical conductors.
4
Ch1. Service information
„ Electrical safety
Observe the following rules when working on electrical equipment.
Important
Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive
fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from
electrical shock.
· Find the room emergency power-off switch, disconnecting switch, or electrical outlet. If an electrical outlet.
If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
· Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
· Disconnect all power before
1. Performing a mechanical inspection
2. Working near power supplies
3. Removing or installing main units
· Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
· If you need to work on a machine that has exposed electrical circuits, observe the following precautions :
Ensure that another person, familiar with the power-off controls, is near you.
Caution
Another person must be there to switch off the power, if necessary.
· Use only one hand when working with powered-on electrical equipment. Keep the other hand in your
pocket or behind your back
Caution
An electrical shock can occur only when there is a complete circuit. By observing the above rule,
you may prevent a current from through your body.
· When using testers, set the controls correctly and use the approved probe leads and accessories for that
tester
5
Ch1. Service information
· Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal
floor strips and machine frames.
· Observe the special safety precautions when you work with very high voltages. These instructions are in
the safety sections of maintenance information. Use extreme care when measuring high voltages.
· Regularly inspect and maintain your electrical hand tools for safe operational condition.
· Do not use worn or broken tools and testers.
· Never assume that power has been disconnected from a circuit. First check that it has been powered off.
· Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
non-grounded power extension cables, power surges, and missing safety grounds.
· Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive such touching can cause personal injury and machine damage.
· Do not service the following parts with the power on when they are removed from their normal operating
places in a machine.
1. Power supply units
2. Pumps
3. Blowers and fans
4. Motorgenerators
and similar units. (This practice ensure correct grounding of the units.)
· If an electrical accident occurs
1. Use caution ; do not become a victim of yourself.
2. Switch off power.
3. Send another person to get medical aid.
6
Ch1. Service information
„ Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions.
As each machine was designed and built, required safety items were installed to protect users and service
personnel from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-LG features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
· Consider these conditions and the safety hazards they present
1. Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
2. Mechanical hazards, such as loose or missing hardware
Refer to the following checklist and begin the checks with the power off, and the power cord disconnected.
· Checklist
1. Check exterior covers for damage (loose, broken, or sharp edges)
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for :
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity
for 0.1
or less between the external ground pin and frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG
alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screw or rivets) have not been removed or tampered with.
7
Ch1. Service information
„ Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between
objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Note
Use product-specific ESD procedures when they exceed the requirements noted here.
Make sure that the ESD protective devices you use have been certified (ISO9000) as fully effective.
· When handling ESD-sensitive parts :
1. Keep the parts in protective packages until they are inserted into the product.
2. Wear a grounded wrist strap against your skin to eliminate static on your body.
3. Prevent the part from touching your clothing. Most clothing retains a charge even when you are wearing
a wrist strap.
4. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
5. Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note
The use of a grounding system is desirable but not required to protect against ESD damage.
a. Attach the ESD ground clip too any frame ground, ground braid, or green-wire ground.
b. Use an ESD ground or reference point when working on a double-insulated or battery-operated
system. You can use coax or connector-outside shells on these systems.
c. Use the round ground-prong of the AC plug on AC-operated computers.
„ Grounding requirements
Electrical grounding of the computers is required for operator safety and correct system function.
Proper grounding of the electrical outlet can be verified by a certified electrician.
8
Ch1. Service information
1-4. Laser compliance statement
When a CD-ROM drive, DVD drive or the other laser product is installed, note the following :
Caution
Use of controls or adjustments or performance of procedures other than those specified here in
might result in hazardous radiation exposure.
Opening the CD-ROM drive, DVD-ROM drive or the other optical storage device could result in exposure
to hazardous laser radiation.
There are no serviceable parts inside those drives. Do not open
Danger
Emits visible and invisible laser radiation when open. Do not stare into the beam , do not view
directly with optical instruments, and avoid direct exposure to the bean.
1-5. Backup (Standby) RTC battery safety information
When replacing or disposing of the backup (standby) RTC battery, note the following :
9
Ch1. Service information
1-6. Read this first
Before you go to the checkout guide, be sure to read this section.
Important Notes
·
Only trained personnel certified by LG should service the computer.
·
Read the entire FRU removal and replacement page before replacing any FRU.
·
Use new nylon-coated screws when you replace FRUs.
·
Be extremely careful during such write operations as copying, saving, formatting.
Drives in the computer that you are servicing sequence might have been altered. If you selected an
incorrect drive, data or programs might be overwritten.
· Replace FRUs only for the correct mode.
· When you replace a FRU, make sure the model of the machine and the FRU part number are correct by
referring to the FRU parts list.
· A FRU should not be replaced because of a single, irreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hard ware defect, such as cosmic radiation,
electrostatic discharge, or software errors.
· Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the
error log and run the test again. If the error does not recur, do not replace the FRU.
· Be careful not to replace a non-defective FRU.
„ What to do first
You must fill out the record form first.
During the warranty period, the customer may be responsible for repair costs if the computer damage was
caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. The following list provides some common items that are not covered under
warranty and some symptoms that might indicate that the system was subjected to stress beyond normal
use. Before checking problems with computer, determine whether the damage is covered under the
warranty by referring to the following :
10
Ch1. Service information
The followings are not covered under warranty :
· CD
panel cracked from the application of excessive force or from being dropped
·
Scratched (cosmetic) parts
·
Distortion, deformation, or discoloration of the cosmetic parts
·
Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessive
force
·
Damage caused by liquid spilled into system
·
Damage caused by improper insertion of a PC Card or the installation of an incompatible card
·
Damage caused foreign material in the diskette drive
·
Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette
with multiple labels
·
Damaged or bent diskette eject button
·
Fusses blown by attachment of a non-supported device
·
Forgotten computer password (making the computer unusable)
·
Sticky keys caused by spilling a liquid onto the keyboard
The following symptoms might indicate damage caused by non-warranted activities :
·
Missing parts might be a symptom of unauthorized service or modification.
·
If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or
dropped.
11
Ch2. Locations
Chapter 2. Locations
„ Front view (15”)
Volume Up
LCD
Volume Down
Power switch
Power-saving mode switch
Keyboard
TouchPad
TouchPad button
Built-in speakers
IrDA port
„ Front view (14.1”)
Volume Up
LCD
Volume Down
Power switch
Power-saving mode switch
Keyboard
TouchPad
TouchPad button
Built-in speakers
12
IrDA port
Ch2. Locations
„ Rear view (15”/14.1”)
Ethernet port
Power jack
Modem port
S-Video
„ Left view (15”/14.1”)
PC card eject button
ODD tray open button
IEEE1394 port
SD memory Card slot
PC card slot
ODD
Emergency eject hole
USB port
„ Right view (15”/14.1”)
Fan louvers
Parallel port
VGA port
Key hole (Kensington Lock)
USB port
Microphone jack
Headphone jack / S-PDIF
Security key hole (Kensington Lock)
User can attach a separately purchased chain lock into the security keyhole and connect it to a fixed object
to prevent a notebook theft
13
Ch3. System information
Chapter 3. System information
„ Specification
• CPU
· Banias 1.3 ~ 1.7 GHz / Dothan 1.7 GHz
· FCPGA
• Main Chipset & Graphic
· Intel ODEM + ICH4
· Intel Montara GME (Graphic Controller Integrated)
· ATi M9+ w/32MB VRAM
· ATi M10 w/64MB VRAM
• Memory
· 2SODIMM – Up to 2GB
· DDR200/266/333 Capable
• HDD
· 2.5” 9.5mm 40/60/80GB
• Communication
· Modem, Daughter Card Type
· 10/100 LAN on Board
· IrDA
• Wireless LAN Solution
· 802.11b Mini PCI Type, Quad-band Antenna
• Cardbus
· 1 Type II Cardbus Socket
· SD Card Slot
· Memory Stick Slot
• ODD
· Fixed Optical Storage
· DVD/COMBO
• Port
· VGA, PIO, 2X USB(2.0), 1X USB(1.1) RJ11, RJ45, Headphone-out / S-PDIF, Mic-in, DC-in, IEEE1394
• Input Devices
· Keyboard (Full sized Keyboard, 2.5mm Key Storke)
· Touchpad
· 3 Buttons (Power, Volume Up, Volume Down)
• Indicator (LED)
· Power, HDD Activity, Caps Lock, Num Lock, Wireless LAN, Battery Charge, AC
• Power
· 65 Watt 18.5V Adapter
• Audio
· 2 Pro Speakers w / 16bit Stereo (SB Pro Compatible) 1W
•Material
· McKinley CFRTP / Rear (Mg)
• Battery
· 6 Cell 4.4Ah Cylindrical (Li-Ion)
· 9 Cell 6.6Ah Cylindrical (Li-Ion)
14
Ch3. System information
„ Model Configuration
15
Ch3. System information
„ System Block Diagram
16
Ch3. System information
„ Fn key combinations
The following table shows the function of each combination of Fn with a function key.
Function of Fn keys has nothing to do with Operating System.
+
Description
User-defined Hot key. (Setting is available at OSD)
User-defined Hot key. (Setting is available at OSD)
User-defined Hot key. (Setting is available at OSD)
Put the computer in standby mode.
To turn the LCD display on again, press any key or TouchPad.
(In Windows XP and Windows 2000, this combination of buttons functions as a sleep button.
The setting can be changed so that pressing it puts the computer into hibernation mode or
even shuts the computer down.)
Enable / Disable TouchPad.
Disable TouchPad by pressing once.
Enable TouchPad by pressing once more.
Enable / Disable Wireless LAN.
Disable Wireless LAN by pressing once.
Enable Wireless LAN by pressing once more.
Switch between the computer display and an external monitor. If an external monitor is
attached, computer output is displayed in the following three patterns by turns:
External monitor (CRT display)
Computer display and external monitor (LCD + CRT display)
Computer display (LCD)
Enable / Disable the auto sound control function with the Battery Miser if it is installed.
(To enable this function, you have to install the Battery Miser first.)
Enable Disable the auto brightness control function with the Battery Miser if it is installed.
(To enable this function, you have to install the Battery Miser first.)
User-defined Hot key. (Setting is available at OSD)
User-defined Hot key. (Setting is available at OSD)
User-defined Hot key. (Setting is available at OSD)
The computer display becomes brighter.
The computer display becomes less bright.
17
Ch3. System information
„ Status indicators
· The system status indicators show the status of the computer.
a
b
c
d
e
a
f
d
14.1”
e
f
g
15”
a. AC Power
Power indicator lights up when the power cord is connected to the computer.
b. Battery
Battery status indicator indicates the following status of the battery.
Green : The computer is connected to an AC adapter and is being charged.
Off : The battery if fully charged OR the computer is not connected to an AC adapter.
Blinking : The battery power is under 10% of its maximum capacity.
c. Power
Power status indicator indicates the following status of the computer.
Green : The computer is turned on.
Off : The computer is turned off or is in hibernation mode.
Blinking : The computer is in standby mode.
d. Drive in use
Drive in use indicator lights up when data is being written to or read from the hard-disk or optical disk
drive.
e. Num Lock
Num Lock indicator lights up when the combination of the
and
key is pressed.
When this indicator lights up, you can use the embedded numeric keys.
(To use the numeric keys, you must enable the Internal Keypad setting under the Advanced menu in
the BIOS Setup Utility)
f. Caps Lock
Caps lock indicator lights up when the Caps lock key is pressed. When this indicator lights up, you can
type capital letters without pressing the
key.
g. Wireless activity indicator
Wireless activity indicator indicates the following.
Blue : The Wireless client is associated with the network.
Off : The Wireless card does not have the power or RF is off.
Blinking : The Wireless client is not associated with the network.
18
Ch3. System information
„ BIOS Flash
You can update BIOS using a floppy disk drive.
Because this system is not equipped with any floppy disk drive, you have to use an external USB drive for
a BIOS update. In order to boot up with an USB drive, please set Removable Device as the first boot up
drive in the boot menu of BIOS setup.
· How to update flash ROM in DOS
1. Create ‘boot up’ flash update diskette.
2. Copy a ROM image file (*.wph) into the root of the flash update diskette.
3. Copy phlash16.exe to the flash update diskette.
4. Insert the diskette into the FDD of your computer.
5. Boot your computer with the diskette, and type ‘phlash16*.wph/mode=n’.
6. Cold boot and follow the instruction displayed on the screen.
· Flash options /mode=n
0 – Default mode. Keep the current DMI information and update BIOS image only.
1 – Update DMI information only.
If new DMI information is not specified, the current DMI information is left unchanged.
2 – Update BIOS and DMI information.
If new DMI information is not specified, the current DMI information is left unchanged.
3 – Update BIOS and DMI information.
DMI information is updated to the DMI string and options specified in the new BIOS image.
Note
DMI is Desktop Management Interface
19
Ch3. System information
„ How to update flash ROM in Windows
1. Quit all running programs.
2. Start WINPHLASH.EXE.
3. Select the procedure you want :
a. Backup BIOS and Flash BIOS with new settings
b. Backup BIOS Only
4. Specify the locations for backup and new BIOS files in BIOS Setting Locations.
a. Enter the name of the backup file for existing BIOS or click Browse to locate the file.
b. Enter the name of the new BIOS file or click Browse to locate the file.
5. Click Advanced Settings button to access the advanced settings
6. Click Flash BIOS button to start flash BIOS.
7. Wait for the operation to complete. WinPhlash may take one or two minutes to complete flash BIOS
operation.
20
Ch3. System information
8. After the completion, ‘System BIOS was successfully updated’ appears on the screen, then the
computer restarts.
9. After the restart, make sure the system BIOS is updated.
10. If your computer does not restart automatically, turn off your computer and then turn it back on by
pressing power button.
21
Ch3. System information
„ BIOS Setup
BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM, and
check the configurations during startup. Use the BIOS Setup Utility to change and save the system
environment, hardware configurations, power saving mode, etc.
· Open the BIOS Setup Utility in the following situations :
1. to change the BIOS setup
2. to replace the backup battery
3. system configuration error occurs
4. to change the boot order
5. to set/change a password
Press the power button.
When the LG logo appears on the screen, press
and enter the BIOS Setup Utility.
22
Ch3. System information
„ Default screen
· BIOS Setup Utility menu bar shows the following menus
Main, Advanced, Security, Boot, Exit
· Main menu enables you to set the system time and date, hard disk drive setup, memory configuration, and
floppy disk drive specification.
· Advanced menu enables you to configure the operating environment for peripheral devices, such as
legacy USB, TouchPad, internal keypad, and parallel port.
· Security menu enables you so set or change supervisor and user passwords.
· Boot menu enables you to set the order of drives the system selects to find its operating system during the
boot sequence. Use Enter, + and - keys to change the order.
· Exit menu enables you to save your system configuration.
23
Ch3. System information
„ Using the keys
The keys used in the BIOS Setup Utility and their functions are described at the bottom.
·
,
+
: General Help
Display the descriptions of the keys used in the setup utility.
·
,
: Select Item
Navigate and select items in the setup utility. The selected item becomes highlighted.
·
,
: Select Menu
Move to another menu.
·
/
,
: Change Values
Change the value of a selected item.
·
: Load Default Configuration
Display Setup Confirmation window. Press Enter to load default configuration.
·
: Select Sub-Menu
Some items have sub-menus. Display the sub-menu for a selected item.
·
: Save and Exit
Display Setup Confirmation window. Press Enter to save and exit.
·
: Exit
In a sub-menu, press Esc to move to the previous window. In Main menu, click Esc to move to Exit menu.
24
Ch3. System information
„ Main Menu
· System Time
Set the system time. Use Tab key to move to hour, minute, and second. Use +, -, or Spacebar to change
the values.
· System Date
Set the system date.
· Processor Type / Speed
Indicate CPU type and clock speed installed on the system.
· BIOS Version / KBC Version / UUID Number
Display BIOS / KBC version information and UUID value.
· Primary Master / Secondary Master
Display the information about the device used as the primary master. Press Enter to set the parameters of
the device at this connection.
· System Memory / Extended Memory
Display the memory size information.
25
Ch3. System information
„ Advanced Menu
· Legacy USB Support
Enable support for the Legacy USB. (Enabled / Disabled)
· TouchPad Support
Enable support for TouchPad. (Enabled / Disabled)
· Internal Keypad
Enable support for the internal keypad. (Enabled / Disabled)
26
Ch3. System information
· Parallel Port
Configure the parallel port using options. (Enabled / Disabled)
Set the mode for the parallel port using options. (Output only, Bi-directional, EPP, and ECP)
Set the base I/O address for the parallel port. (378 / 278 / 3BC)
Set the interrupt for the parallel port. (IRQ5 / IRQ7)
· Parallel port modes
1. Output only
The normal mode. Use this mode when you connect a printer to the parallel port.
2. Bi-directional
Allows bi-directional high speed data transfer.
3. EPP (Extended Parallel Port)
Allows a connection to a device supporting EPP, EPP uses the existing parallel port signal to allow
asymmetric bi-directional data transfer with a host device.
4. ECP (Extended Capabilities Port)
Allows a connection to a device supporting ECP, ECP increases the data transfer rate and enables you
to set DMA channel. (DMA1 / DMA3)
· Boot-time Diagnostic Screen
Enables the Boot-time Diagnostics Screen (Enabled / Disabled)
27
Ch3. System information
„ Security Menu
· Setting a password
If you want to protect the system setup from an unauthorized user, follow the instructions below to set a
password.
You can set a password in the BIOS Setup Utility program.
Caution
If you forget the password, you cannot gain access to your system.
Make sure you write down the password in a safe place only you can refer to in case you forget
the password
· Set Supervisor Password
A password protects your computer from unauthorized users. The factory default setup does not have a
password. A supervisor password prevents unauthorized users from changing the system setup.
a. Start the system setup utility and use arrow keys to select Set Supervisor Password under
Security menu, and then press Enter.
b. If the following screen appears, select Set Supervisor Password by using arrow keys, and Enter.
28
Ch3. System information
Note
A supervisor password enables you to change settings in the BIOS Setup Utility and to perform
Power on Boot.
Users other than the administrator should only have user passwords.
c. If the following message appears, enter a new supervisor password and then Enter.
A password must be consisted of character A~Z and numbers 0~9, and have the maximum
length of 8.
d. If the following message appears, press Enter.
e. Press F10 to save the new settings.
f. If the following message appears, select Yes and press Enter to restart the computer.
29
Ch3. System information
· Set User Password
A user password provides a lower level of security compared to a supervisor password.
A supervisor password must be set in order for you to set a user password.
a. Start the BIOS Setup Utility and use arrow keys to select Security menu.
b. Use arrow keys to selected Set User Password and press Enter.
Note
A user password gives limited access for changing the setting in the BIOS Setup Utility compared to
a supervisor password.
c. If the following message appears, enter a new password and press Enter.
A password must be consisted of characters A~Z and numbers 0~9, and have maximum
length of 8.
30
Ch3. System information
d. If the following message appears, press Enter.
e. Press F10 to save the new settings.
f. If the following message appears, select Yes and press Enter to restart the computer.
31
Ch3. System information
· Password on boot
Enables password entry on boot
a. Start the BIOS Setup Utility and use arrow keys to select Security menu.
b. If the following screen appears, select Set Supervisor Password or Set User Password by using
arrow keys, and input new password.
32
Ch3. System information
c. Select Password on boot menu, then change value (Enabled) by using +, - keys.
Note
If you set a Supervisor Password or User Password, you can use Password on boot.
If you set Disabled on Password on boot, You don’t have to enter a password.
33
Ch3. System information
· Set HDD Password
Set HDD Password to control access to the Hard-disk.
Press Enter to input, change or disable hard-disk password.
a. Start the BIOS Setup Utility and use arrow keys to select Security menu.
b. If the following screen appears, select Set HDD Password by using arrow keys, and press Enter.
Note
When loosing your HDD Password, you can not access your Hard-disk drive.
34
Ch3. System information
c. If the following message appears, enter a new supervisor password and then press Enter.
A password must be consisted of numbers 0~9, and have the maximum length of 8.
d. If the following message appears, press Enter.
e. Press F10 to save the new settings.
f. If the following message appears, select Yes and press Enter to restart the computer.
35
Ch3. System information
· Changing or removing a password
You must know the password in order to change or remove it.
a. Start the BIOS Setup Utility, enter your password, and then press Enter.
b. To change the password, follow the instructions on Set Supervisor Password or
Set User Password.
c. To remove the password, follow the instructions below.
Use arrow keys to select Security menu, and select a password you want to remove, and then press
Enter.
d. If the following message appears, enter the current password in the bracket next to
Enter Current Password, and then press Enter.
Enter
Enter
e. Press Enter without entering a new password in each of the brackets next to Enter New Password
and Confirm New Password.
f. If the following message appears, press Enter.
g. Press F10 to save the new setting.
h. If the following message appears, select Yes and press Enter to restart the computer.
36
Ch3. System information
„ Boot Menu
· Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices, Hard drive, and
Network boot.
Boot menu displays the boot order of your system with higher priority given to a device higher on the list.
The default boot order is CD-ROM drive, Removable devices, Hard drive, and Network boot.
Changing the order of the devices on Boot menu changes the boot order of your system.
Use
and
keys to select a device. Press the combination of Shift and + to move the device up,
and - to move the device down on the list.
· CD-ROM Drive
The CD-ROM drive has the highest priority given in the boot order. Boot your system using the CD-ROM drive
by inserting a bootable CD in the CD-ROM(CD-RW/DVD combo) drive
· Removable Devices
You can set the boot order for more than one removable device, such as a legacy floppy drive.
· Hard
Drive
You can set the boot order for more than one hard disk drive.
37
Ch3. System information
„ Exit Menu
· Exit System Setup and save your changes to CMOS.
· Exit Saving Changes
Select Exit Saving Changes to save new setup information in CMOS RAM. CMOS RAM stores the
information using the backup battery; there fore, the information will not be lost when the computer is
turned off.
· Exit Discarding Changes
Select Exit Discarding Changes to discard new setup information. If you made changes to items other
than date, time, and passwords, the Setup Warning asks you to save the new configurations.
Select Yes and press Enter to save the new configuration.
· Load Setup Defaults
Select Load Setup Defaults to change the setup information to the factory default settings. If you select
Load Setup Defaults or press F9, Setup Confirmation asks you to confirm your selection.
Press Yes to load setup defaults.
38
Ch3. System information
· Discard Changes
Select Discard Changes to discard new setup information. Setup Confirmation asks you to confirm
your selection. If you want to discard any new setup information, select Yes.
· Save Changes
Select Save Changes to save any new setup information without exiting the BIOS Setup Utility.
Select Yes to save the new setup information in the Setup Confirmation window.
39
Ch4. Symptom-to-part index
Chapter 4. Symptom-to-part index
The symptom-to-part index in this section lists symptoms and errors and their possible causes.
The most likely cause is listed first.
Note
If replacing a part (FRU) does not solve the problem, put the original part back in the computer.
Do not replace a non-defective FRU.
„ Power system checkout
· To verify a symptom, do the following :
1. Power off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Check that power is supplied when you power on the computer.
5. Power off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you power on the computer.
· If you suspect a power problem, see the appropriate one of the following power supply checkouts :
1. Checking the AC adapter
2. Checking the operational charging
3. Checking the battery pack
4. Checking the backup battery
· Checking the AC adapter
If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity
and installation.
If the computer does not charge during operation, go to ‘Checking operational charging’.
To check the AC adapter, do the following :
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the
2
1
AC adapter cable. See the following figure :
40
Pin
Voltage (V dc)
1
+18.0 ~ +19.2
2
Ground
Ch4. Symptom-to-part index
· If the voltage is not correct, replace the AC adapter.
· If the voltage is acceptable, do the following :
1. Replace the system board.
2. If the problem persists, check the AC adapter whether it is correct product or not.
Note
Noise from the AC adapter does not always indicate a defect.
· Checking operational charging
1. To check whether the battery charges properly during operation, use a discharged battery pack or a
battery pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
does not turn on, replace the battery pack.
2. If the charge indicator still does not turn on, replace the system board.
Then reinstall the battery pack.
Note
Do not charge battery pack, when its temperature is below 0
or above 60
.
· Checking the battery pack
1. Open the Power Meter window by clicking Start
Control Panel
Power Options and then;
check the total power remains. Battery charging does not start until the power Meter shows that less
than 95% of the total power remains; under this condition the battery pack can charge to 100% of its
capacity. This protects the battery pack from being overcharged or from having a shortened life.
2. To check the status of your batter, move your cursor to the Power Meter icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power
remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.
Note
If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and
Leave it at room temperature for a while. After it cools down, reinstall and recharge it.
41
Ch4. Symptom-to-part index
· The Characteristics of the battery pack
1. Self-discharge
The battery gradually loses its power over time without ever being used.
2. Periodic full discharge / charge
Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,
you can perform the full discharge / charge to improve the capacity. You should perform periodic full
discharge /charge once every 30~60 days.
You should always use the battery until its power is low; then fully charge the battery.
3. Trickle charge
If the temperature of the battery pack drops below 10
, the trickle charging begins.
The trickle charging may take 32 hours for the battery pack to be fully charged.
42
Ch4. Symptom-to-part index
· To check the battery pack, do the following :
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+).
See the following figure :
5(+)
4
3
2
Terminal
Voltage (V dc)
1
Ground(-)
5
+0V ~ +12.6V
(6 cell / 9-cell)
1(-)
3. If the voltage is still less than +11.1 V DC after recharging, replace the battery.
4. If the voltage is more than +11.1 V DC, measure the resistance between battery terminals 1 and 2.
The resistance must be 2 to 4
(typically 3
).
5. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system
board.
Note
Charging will take at least 3 hours.
Note
Battery is an expendable supplier, so its capacity and used time can be reduced by using the computer.
· Checking the backup battery
1. Remove the backup battery.
2. Measure the voltage of the backup battery. See the following figure.
White (+)
Blue (+)
Wire
Voltage (V dc)
White
+2.5 ~ +3.2
Blue
Ground
If the voltage is correct, replace the system board.
If the voltage is not correct, replace the backup battery.
If the backup battery discharges quickly after replacement, replace the system board.
43
Ch4. Symptom-to-part index
„ Numeric error codes
Symptom / Error
FRU or action, in sequence
0200
Fixed disk failure
(The hard disk is not working)
1.Reset the hard-disk drive.
2.Load Setup Defaults in BIOS Setup Utility.
3.Hard-disk drive.
4.System board.
0210
Stuck Key error
1.Check the keyboard if it is pressed.
2.Replace the keyboard.
0211
Keyboard error
Run interactive tests of the keyboard and the auxiliary
input device.
0212
Keyboard Controller Failed
System board.
0220
Monitor type error - Monitor type does not
match the one specified in CMOS.
Load Setup Defaults in BIOS Setup Utility.
0230
System RAM error - System RAM Failed at
offset.
1.DIMM
2.System board
0231
Shadow RAM error - Shadow RAM failed at
offset
System board
0232
Extended RAM error - Extended RAM Failed
at address line
1. DIMM
2. System board
0250
System battery error - System battery is dead
Replace the backup battery and run BIOS Setup Utility
to reset the time and date.
44
Ch4. Symptom-to-part index
Symptom / Error
FRU or action, in sequence
0251
System CMOS checksum bad
- System CMOS checksum is not correct.
- Default configuration used.
Replace the backup battery and run BIOS Setup Utility
to reset the time and date.
0252
Password checksum bad - The password is
cleared.
Reset the password by running BIOS Setup Utility.
0260
System timer error
1. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
2. System board.
0271
Check date and time settings - Date and time
error.
Run BIOS Setup Utility to reset the time and date.
0280
Previous boot incomplete
- Default configuration used
1. Load ‘Setup Default’ in BIOS Setup Utility.
2. DIMM.
3. System board.
0281: Memory Size found by POST differed
from EISA CMOS
Load Setup Defaults in BIOS Setup Utility.
02B0
Diskette drive A error
Set up the diskette type in BIOS Setup Utility.
02B1
Diskette drive B error
Set up the diskette type in BIOS Setup Utility.
02B2
Incorrect drive A type - Floppy diskette drive
error
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02B3
Incorrect Drive B type
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02D0
System cache error - Cache disabled
(RAM cache failed and BIOS disabled)
1. Load ‘Setup Default’ in BIOS Setup Utility.
2. System board.
02F4
EISA CMOS not writable
1. Load ‘Setup Default’ in BIOS Setup Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed
1. DIMM
2. System board
02F6
Software NMI failed
1. DIMM
2. System board
45
Ch4. Symptom-to-part index
Symptom / Error
FRU or action, in sequence
02F7
Fail - Safe timer NMI failed
1. DIMM
2. System board
0611
IDE configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0612
IDE configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0613
Com A configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0614
Com A configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0615
Com B configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0616
Com B configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0617
Floppy configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0618
Floppy configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0619
Parallel port configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
061A
Parallel port configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
46
Ch4. Symptom-to-part index
„ Error message
Symptom / Error
FRU or action, in sequence
Device address conflict.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid System Configuration Data.
1. DIMM.
2. System board.
I/O Device IRQ Conflict.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Operating System not found.
1. Check that the operating system has no failure and
is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard
-disk drive and the diskette drive are properly
identified.
3. Reset the hard-disk drive.
4. Reinstall the operating system.
5. Diskette drive.
6. Hard-disk drive.
7. System board.
Hibernation error.
1. Restore the system configuration to what it was
before the computer entered hibernation mode.
2. If memory size has been changed, re-create the
hibernation file.
FAN error.
Fan.
Thermal sensing error.
System board.
47
Ch4. Symptom-to-part index
„ LCD-related symptoms
Note
Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack also.
Symptom / Error
FRU or action, in sequence
LCD screen becomes dark suddenly.
Check out Battery Miser.
Nothing displayed on LCD screen.
1. Check out Battery Miser.
2. Choose Never in the Turn off Monitor item on
Power Options Properties.
3. Check the power save mode switch if it is pressed
by something.
4. Check the System is in standby or hibernation
mode.
LCD backlight not working.
LCD too dark.
LCD brightness cannot be adjusted.
1. Reconnect inverter to the board connector.
2. Replace inverter.
3. LCD assembly.
4. System board.
LCD color cannot be adjusted.
LCD screen abnormal.
Characters missing pixels.
LCD screen unreadable.
Wrong color displayed.
1. Reset all LCD connectors.
2. Replace LCD cable.
3. LCD assembly.
4. System board.
Horizontal or vertical lines displayed
on LCD
LCD assembly.
Power-on indicator on, and a blank LCD
during POST.
LCD assembly.
System board.
48
Ch4. Symptom-to-part index
„ Indeterminate problems
· You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices
are installed, a short circuit is suspected, or the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
· Verify that all attached devices are supported by the computer.
· Verify that the power supply being used at the time of the failure is operating correctly.
1. Power off the computer
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnected all of the following devices :
a. Non-LG devices.
b. Printer, mouse, and other external devices.
c. Battery pack.
d. PC cards.
e. ODD (CD-ROM, Combo) drive or FDD drive in the Bay.
f. Hard-disk drive.
Note
Use the other memory card because it needs when operating computer.
4. Power on the computer.
5. Determine whether the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time.
(do not replace a non-defective FRU)
a. LCD assembly (Check external monitor whether the same problem recurs or not).
b. Keyboard.
c. Keydeck (TouchPad and Scroll Button assembly).
d. System board.
49
Ch5. Removing and replacing a part
Chapter 5. Removing and replacing a part (FRU)
Danger
Before removing any FRU, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
Caution
Before the computer is powered on after FRU replacement, make sure that all screws, springs,
and other small parts are in place and are not loose inside the computer. Verify metal flakes can
cause electrical short circuits.
Note
As for the screw, every Torque 2
0.2Kgfcm(0.196Nm)
50
Ch5. Removing and replacing a part
„ 1010 Battery Pack
1. Push the battery latch in the direction shown below, then slide the battery pack out of the slot.
51
Ch5. Removing and replacing a part
„ 1020 Hard Disk Drive
Remove the following parts in order before replacing this part.
a. Battery Pack(1010)
1. Remove a screw as indicated in the picture, then pull the HDD assembly out in the direction shown below.
1
No.
FRU No.
Specification
Qty
1
1SZZBA4011E
M3.0 X L5.0
1
52
Ch5. Removing and replacing a part
„ 1030 Retainer
Remove the following parts in order before replacing this part.
a. Battery Pack(1010)
1. Remove 2 screws.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4083A
M2.0 X L8.0
2
53
Ch5. Removing and replacing a part
2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard,
and pull it up.
54
Ch5. Removing and replacing a part
3. Disconnect the keyboard connector.
55
Ch5. Removing and replacing a part
„ 1040 Retainer
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030)
1. Pull up the retainer, and remove the connector using a (-) type screwdriver.
56
Ch5. Removing and replacing a part
„ 1050 Fan Assembly
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040)
1. After removing a screw and the connector, pull up and remove the fan assembly using a (-) type
1
screwdriver.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4020A
M2.0 X L8.8
3
57
Ch5. Removing and replacing a part
58
Ch5. Removing and replacing a part
„ 1060-1 Optical Disk Drive (15” Model)
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040)
1. Remove a screw, insert a screwdriver into the hole located at the rear of ODD and push it out.
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4014A
M2.0 X L5.0
1
59
Ch5. Removing and replacing a part
„ 1060-2 Optical Disk Drive (14.1” Model)
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040)
1. Remove a screw, insert a screwdriver into the back side of ODD and push it out.
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4014A
M2.0 X L5.0
1
60
Ch5. Removing and replacing a part
„ 1070 Wireless LAN Card
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040)
1. Remove two wireless LAN card connector, open card knob to take out the card.
61
Ch5. Removing and replacing a part
„ 1080 MDC Modem Card
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040)
1. Remove two screws and insert a screwdriver below the modem. Pull it up to disassemble.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4017B
M2.0 X L3.5
2
62
Ch5. Removing and replacing a part
„ 1090 Display Module
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Wireless LAN Card(1070)
1. Remove two screws.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4039B
M2.5 X L8.0
2
63
Ch5. Removing and replacing a part
2. Remove two hinge cover screws.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4014A
M2.0 X L5.0
2
64
Ch5. Removing and replacing a part
3. Using a (-) type screwdriver from the back of LCD, pull up the hinge cover with your finger. Then more
you move the LCD to the back, the easier the hinge cover will pull out. Remove another hinge cover
located on the other side.
4. Remove two hinge screws.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4039B
M2.5 X L8.0
2
65
Ch5. Removing and replacing a part
5. Remove the LCD connector located at the upper end of MCD modem. You will see a tag designed to
make work easier. Pull out the tag.
4. Remove the LCD cable.
66
Ch5. Removing and replacing a part
7. Hold the LCD with your both hands, and pull it up to remove.
Note
Display Module disassembly in detail (1140)
67
Ch5. Removing and replacing a part
„ 1100 Keyboard Deck
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050)
e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090)
1. Remove 14 screws (for 15” model) or 11 screws (for 14.1” model).
The screw type is shown on the set for your reference.
15”
1
1
Screw Type
1
1
1
1
1
2
1
1
1
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4083A
M2.0 X L8.0
13
2
1SZZBA4067A
M2.0 X L13.0
1
68
Ch5. Removing and replacing a part
14.1”
1
1
1
1
Screw Type
1
Screw Type
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4083A
M2.0 X L8.0
10
2
1SZZBA4067A
M2.0 X L13.0
1
69
Ch5. Removing and replacing a part
2. Open the I/O port cover and remove two screws.
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4017B
M2.0 X L3.5
2
70
Ch5. Removing and replacing a part
3. Remove 3 screws.
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4018B
M2.0 X L2.0
3
71
Ch5. Removing and replacing a part
4. Remove the cable, hold the keyboard deck with your both hands and pull it out.
72
Ch5. Removing and replacing a part
5. Remove the speaker cable located at the front of key deck that is pulled up.
73
Ch5. Removing and replacing a part
„ 1110 Main Board
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050)
e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090)
h. Keyboard Deck(1100)
1. Remove two screws and disassemble the ODD Plate Assembly.
1
1
No.
FRU No.
Specification
Qty
1 (14.1”)
1SZZBZ3009B
M2.0 X L2.5
2
1 (15”)
1SZZBZ4014A
M2.0 X L5.0
2
74
Ch5. Removing and replacing a part
2. Remove the PCMCIA board.
3. Remove the RTC battery connector from Main Board.
75
Ch5. Removing and replacing a part
4. Remove the S-Video connector.
5. Remove the LAN S/B connector.
76
Ch5. Removing and replacing a part
6. Remove the power cable.
7. Remove 4M/B screws.
2
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4014A
M2.0 X L5.0
3
2
1SZZBA4017B
M2.0 X L3.5
1
77
Ch5. Removing and replacing a part
8. Hold M/B with your both hand and pull it up to remove.
78
Ch5. Removing and replacing a part
„ 1120 Battery Frame Assembly
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050)
e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090)
h. Keyboard Deck(1100) i. Main Board(1110)
1. Remove a screw.
1
No.
FRU No.
Specification
Qty
1
1SZZBA4017B
M2.0 X L3.5
1
79
Ch5. Removing and replacing a part
2. Pull up the battery frame finger plate, and remove the battery frame assembly. The LAN S/B will be
removed as well when the battery frame assembly is disassembled.
80
Ch5. Removing and replacing a part
„ 1130 S-Video Sub-Board
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050)
e. Wireless LAN Card (1070) f. MDC Modem Card(1080) g. Display Module(1090)
h. Keyboard Deck(1100) i. Main Board(1110)
1. Remove the S-Video sub-board.
81
Ch5. Removing and replacing a part
„ 1140 Display Module
Remove the following parts in order before replacing this part.
a. Battery Pack(1010) b. Keyboard(1030) c. Retainer(1040) d. Fan Assembly(1050)
e. Wireless LAN Card (1070)
1. Using a knife, remove the logo and rubbers that are covering the screws. Then remove all 7 screws.
1
1
1
1
1
2
2
No.
FRU No.
Specification
Qty
1
1SZZBA4044B
M2.5 X L4.0
5
2
1SZZBA4068A
M2.5 XL5.0
2
82
Ch5. Removing and replacing a part
2. Disassemble the LCD front. The front hook located on the middle of LCD upper and lower end.
Be careful of the direction when removing because it is connected from inside out.
83
Ch5. Removing and replacing a part
3. Remove cable connector. Remove the cable that is arranged around LCD from LCD frame.
84
Ch5. Removing and replacing a part
4. Remove 9 screws (for 15” model) or 8 screws (for 14.1”).
1
1
3
1
1
(15”)
2
2
2
2
No.
FRU No.
Specification
Qty
1
1SZZBZ3009B
M2.0 X L2.5
4
2
1SZZBA4044B
M2.5 XL4.0
4
3
(15”)
1SZZBA4041A
M2.0 X L3.0
1
85
Ch5. Removing and replacing a part
5. Press the hook on the both side of LCD with a (-) type screwdriver and remove from the LCD real panel.
86
Ch5. Removing and replacing a part
6. Remove LCD from the LCD rear panel.
87
Ch6. Part lists
Chapter 6. Part lists
2004. 4. 28. MKB21
Location
LG P/N
SPECIFICATION
MKL02
6304FLP081A
TFT LCD, LG PHILIPS LP150E06-A2 15.0 INCH SXGA+
MKL02
6304FLP080A
TFT LCD, LG PHILIPS LP150X08-A3M1 15.0 INCH XGA
MKL02
6304FAU002B
TFT LCD, AU B150XG01 15.0 INCH XGA
MKL02
6304FBH005A
TFT LCD, BOE-HYDIS HT15X34-100 15.0 INCH XGA
MKL03
3111BZ7101A
CASE ASSY, FRONT 15.0"
MKL04
4940BM4146A
KNOB, LATCH
MKL05
4026BM3013A
LATCH, DISPLAY
MKL06
4970BW4540A
SPRING, LCD LATCH
MKL07
4850BM4010A
CUSHION, RUBBER UPPER
MKL08
4850BM4011A
CUSHION, RUBBER LOWER
MKL09
4775B00033A
HINGE ASSY, LEFT 15.0"
MKL10
4775B00034A
HINGE ASSY, RIGHT 15.0"
MKL11
6851B76028A
CABLE ASSY, LCD 15.0"
MKL12
6871BZT17AA
CABLE FPC, WIRELESS INDICATOR 15.1"
MKL13
6708BI0082A
INVERTER, ALPS KUBNKM063A
MKL13
6708BI0083A
INVERTER, DELTA DAC-08B043A
MKL14
3110BD0009B
REAR CASE, 15.0" FOR EXPORT
MKL14
3110BD0009D
MCKINLEY MG DISPLAY REAR 15.0" FOR MC REFRESH
MKL15
3858BZ3019A
INSULATOR, INVERTER 14.1"/15.0"
MKL16
3301BZ0512B
ANTENNA, WIRELESS RIGHT
MKL17
3550BM2093B
DECORATION COVER, 15.0" FOR EXPORT
MKL18
3301BZ0513B
ANTENNA, WIRELESS LEFT
MKL20
6304FBH004A
TFT LCD, BOE HYDIS HT14X1B-110 14.1 INCH XGA
MKL20
6304FLP079A
TFT LCD, LG PHILIPS LP141X13-C2 14.1 INCH XGA
MKL20
6304FLP079B
LP141X13-C2K1 LG PHILPS TFT COLOR 14.1 INCH XGA(1024X768) ISP STYLE B
MKL21
3111BZ7100A
CASE ASSY, FRONT 14.1"
MKL22
3680BM3036A
LENS, WIRELESS REAR 14.1"
MKL23
3550BM1149B
DECORATION COVER, 14.1" FOR EXPORT
MKL24
4775BZ1004A
HINGE ASSY, LEFT 14.1"
MKL25
4775BZ1005A
HINGE ASSY, RIGHT 14.1"
MKL26
6851B76024A
CABLE ASSY, LCD 14.1"
MKL27
3858BZ3020A
INSULATOR, LED 14.1"
MKL28
3110BD0008B
REAR CASE, 14.1" FOR EXPORT
88
REMARKS
For refresh
model
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKL28
3110BD0008D
MCKINLEY MG DISPLAY REAR 14.1" FOR MC REFRESH
MKL29
6871BZT16ZA
CABLE FPC, WIRELESS INDICATOR 14.1"
MKL30
3850BB3035D
MODEL NAME LABEL, MCKINLEY 14.1" FOR EXPORT
MKL30
3850BB3035E
MODEL NAME LABEL, MCKINLEY 15.0" FOR EXPORT
MKL30
3850BB3035P
MCKINLEY N N MODEL NAME LABEL 14.1" MCKINLEY LM40A FOR REFRESH
EXPORT
For refresh
model
MKL30
3850BB3035Q
MCKINLEY N N MODEL NAME LABEL 15" MCKINLEY LM50A FOR REFRESH
EXPORT
For refresh
model
MKL31
3858BZ4450B
MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG
For refresh
model
MKB01
6871BF100A1
MAINBOARD ASSY, BH M9+ P.P LGE 8 LAYERS REV 0.5
MKB01
6871BF200A1
MAINBOARD ASSY, BH M10 P.P LGE 8 LAYERS REV 0.5
MKB01
6871BF300A1
MCKINLEY US007506 REFRESH MODEL . LGE 8 LAYERS REV 0.7 M11
MAINSTEAM MAIN ASSY
MKC01
0IMMRSS090A
MEMORY, SAMSUNG M470L3224FT0-CB3 SODIMM 256MB DDR 333MHZ
MKC01
0IMMRHY044A
MEMORY, HYNIX HYMD232M646C6-J SODIMM 256MB DDR 333MHZ
MKC01
0IMMRIH032A
MEMORY, INFINEON HYS64D32020GDL-6-B SODIMM 256MB DDR 333MHZ
MKC01
0IMMRSS091A
MEMORY, SAMSUNG M470L6423EN0-CB3 SODIMM 512MB DDR 333MHZ
MKC01
0IMMRIH033A
MEMORY, INFINEON HYS64D64020GBDL-6-B SODIMM 512MB DDR 333MHZ
MKC02
2029BG0100A
DVD/CDRW COMBO, TOSHIBA SD-R9012 8X 16X 8X 24X BUILT IN 9.5 MM
MKC02
6777BG0001A
DVD, TEAC DV-28E-BC-43 8X 24X BUILT IN 9.5 MM
MKC04
6871BZT13A4
WIRELESS LAN, INTEL WM3B2100WW MINI-PCI TYPE IIIB
MKC04
6871BZT14A4
MCKINLEY N WM3B2200BGRW PRO/WIRELESS2200BG LAN MINI-PCI TYPE INTEL
4 LAYERS 1-14 NETWORK CONNECTION
MKC04
6871BZT13A5
WM3B2100NA1 MINI-PCI TYPE IIIB INTEL 4 LAYERS 1-11 PRO/WIRELESS2100
LAN MINI-PCI TYPE 3B ADAPTER LIO
MKC05
6871BG105AA
MDC MODEM, AMBIT T60M283.13 56K
MKC06
6911BZ0045B
LI-ION BATTERY, SIMPLO 4400MAH 3S-2P
MKC06
6911BZ0046B
LI-ION BATTERY, SIMPLO 6600MAH 3S-3P
MKC07
5901B09265A
FAN ASSY, W/ SHEET
MKC08
3823B70004A
MCKINLEY LG-IBM SUNREX-K021102A US-ENG 14.1" 84 KEY
MKC08
3823B71004A
MCKINLEY LG-IBM SUNREX US-ENG LM REFRESH 14"
89
REMARKS
For refresh
For refresh
model
For refresh
model
USA,Canada,
Taiwan
For refresh
model
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKC08
3823B70004C
MCKINLEY LG-IBM SUNREX-K021102A RUSSIAN 14.1" 84 KEY
MKC08
3823B71004C
MCKINLEY LG-IBM SUNREX RUSSIAN LM REFRESH 14"
MKC08
3823B70004D
MCKINLEY LG-IBM SUNREX K021167 ARABIAN 14.1" 84 KEY
MKC08
3823B71004D
MCKINLEY LG-IBM SUNREX ARAB LM EFRESH 14"
MKC08
3823B70004E
MCKINLEY LG-IBM SUNREX K021167 HEBREW 14.1" 84 KEY
MKC08
3823B71004E
MCKINLEY LG-IBM SUNREX HEBREW LM REFRESH 14"
MKC08
3823B70004F
MCKINLEY LG-IBM SUNREX K021167 FARSI(IRAN) 14.1" 84 KEY
MKC08
3823B71004F
MCKINLEY LG-IBM SUNREX FARSI LM REFRESH 14"
MKC08
3823B70004H
MCKINLEY LG-IBM SUNREX K021167 US SOUTH AFRICA 14.1" 84 KEY
MKC08
3823B71004H
MCKINLEY LG-IBM SUNREX US SOUTH AFRICA LM REFRESH 14"
MKC08
3823B70004G
MCKINLEY LG-IBM SUNREX K021167 UKRAINIAN 14.1" 84 KEY
MKC08
3823B71004G
MCKINLEY N SUNREX UKRAINIAN LM REFRESH 14"
MKC08
3823B70004K
MCKINLEY LG-IBM SUNREX K021167 SPANISH 14.1" 84KEY
MKC08
3823B70004J
MCKINLEY LG-IBM SUNREX K021167 PORTUGUESE 14.1" 84 KEY
MKC08
3823B70004L
MCKINLEY LG-IBM SUNREX K021167 POLISH 14.1" 84KEY
MKC08
3823B71004L
MCKINLEY LG-IBM SUNREX POLISH LM REFRESH 14"
MKC08
3823B70004M
MCKINLEY N SUNREX K021167 FRENCH 14.1" 84KEY
MKC08
3823B71004M
MCKINLEY LG-IBM SUNREX FRENCH REFRESH LM 14"
MKC08
3823B70004N
MCKINLEY N SUNREX THAILAND 14" 84KEY
MKC08
3823B71004N
MCKINLEY N SUNREX THAILAND LM REFRESH 14"
MKC08
3823B70004P
MCKINLEY LG-IBM SUNREX TAIWAN 14.1" 84KEY
MKC08
3823B71004P
MCKINLEY N SUNREX TAIWAN LM REFRESH 14"
For refresh
model
MKC08
3823B71004Q
MCKINLEY N SUNREX HUNGARY REFRESH LM 14"
For refresh
model
90
REMARKS
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKC08
3823B71004R
MCKINLEY N SUNREX CZECH LM REFRESH 14"
For refresh
model
MKC08
3823B71004S
MCKINLEY N SUNREX TURKEY REFRESH LM 14"
For refresh
model
MKC08
3823B70008A
MCKINLEY LG-IBM OKI US-ENG 15" 86 KEY
MKC08
3823B71008A
MCKINLEY LG-IBM OKI US LM REFRESH 15"
MKC08
3823B70008C
MCKINLEY LG-IBM OKI RUSSIAN 15" 86 KEY
MKC08
3823B71008C
MCKINLEY LG-IBM OKI RUSSIAN LM REFRESH 15"
MKC08
3823B70008D
MCKINLEY LG-IBM OKI ARABIAN 15" 86 KEY
MKC08
3823B71008D
MCKINLEY LG-IBM OKI ARAB LM REFRESH 15"
MKC08
3823B70008E
MCKINLEY LG-IBM SUNREX-K020346A HEBREW 15" 86 KEY
MKC08
3823B71008E
MCKINLEY LG-IBM OKI HEBREW LM REFRESH 15"
MKC08
3823B70008F
MCKINLEY LG-IBM OKI FARSI 15" 86 KEY
MKC08
3823B71008F
MCKINLEY LG-IBM OKI FARSI LM REFRESH 15"
MKC08
3823B70008H
MCKINLEY LG-IBM OKI US SOUTH AFRICA 15" 86KEY
MKC08
3823B71008H
MCKINLEY LG-IBM OKI US SOUTH AFRICA LM REFRESH 15"
MKC08
3823B70008G
MCKINLEY LG-IBM OKI UKRAINAIN 15" 86 KEY
MKC08
3823B71008G
MCKINLEY N OKI UKRAINAIN LM REFRESH 15"
MKC08
3823B70008K
MCKINLEY LG-IBM OKI SPANISH 15" 86KEY
MKC08
3823B70008J
MCKINLEY LG-IBM OKI PORTUGUESE 15" 86KEY
MKC08
3823B70008L
MCKINLEY LG-IBM OKI POLISH 15" 87KEY
MKC08
3823B71008L
MCKINLEY LG-IBM OKI POLISH LM REFRESH 15"
MKC08
3823B70008M
MCKINLEY N OKI FRENCH 15" 87KEY
MKC08
3823B71008M
MCKINLEY LG-IBM OKI FRENCH REFRESH LM 15"
MKC08
3823B70008N
MCKINLEY LG-IBM SUNREX THAILAND 15" LM 84KEY
91
REMARKS
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKC08
3823B71008N
MCKINLEY N OKI THAILAND LM REFRESH 15"
MKC08
3823B70008P
MCKINLEY LG-IBM OKI TAIWAN 15" LM 86KEY
MKC08
3823B71008P
MCKINLEY N OKI TAIWAN LM REFRESH 15"
For refresh
model
MKC08
3823B71008Q
MCKINLEY N OKI HUNGARY LM REFRESH 15"
For refresh
model
MKC08
3823B71008R
MCKINLEY N OKI CZECH LM REFRESH 15"
For refresh
model
MKC08
3823B71008S
MCKINLEY N OKI TURKEY LM REFRESH 15"
For refresh
model
MKC10
0IMCRIN103B
PROCESSOR, INTEL RH80535GC0131M 478P UFCPGA PENTIUM-M
1300MHZ/600MHZ B1-STEPPING(SL6N4)
MKC10
0IMCRIN104B
PROCESSOR, INTEL RH80535GC0171M 478P UFCPGA PENTIUM-M
1400MHZ/600MHZ B1-STEPPING(SL6F8)
MKC10
0IMCRIN105B
PROCESSOR, INTEL RH80535GC0211M 478P UFCPGA PENTIUM-M
1500MHZ/600MHZ B1-STEPPING(SL6F9)
MKC10
0IMCRIN106B
PROCESSOR, INTEL RH80535GC0251M 478P UFCPGA PENTIUM-M
1600MHZ/600MHZ B1-STEPPING(SL6FA)
MKC10
0IMCRIN119A
PROCESSOR, INTEL RH80535GC0291M 478P UFCPGA PENTIUM-M
1700MHZ/600MHZ B1-STEPPING(SL6N5)
MKC10
0IMCRIN150A
RH80535NC009512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1200MHZ/400MHZ B1-STEPPING(SL79S)
MKC10
0IMCRIN132A
RH80535NC013512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1300MHZ/400MHZ B1-STEPPING(SL6N7)
MKC10
0IMCRIN133A
RH80535NC017512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1400MHZ/400MHZ B1-STEPPING(SL6N6)
MKC11
6708BA0036B
ADAPTER, LITEON PA-1650-02L1 65W 18.5V/3.5A 3PIN
MKC11
6708BA0044B
ADAPTER, HIPRO HP-OK065B133 65W 16V/3.5A 3PIN
MKC12
6910C00007A
RTC BATTERY, MINAMOTO CR2032 3.0 VOLT 210MAH
MKC12
6910C00005A
RTC BATTERY, SONY CR2032 3.0 VOLT 200MA
MKC13
6410BD21003
PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK
MKC13
6410BK21005
PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BK20704
213356-001(SP502A+IS34) I-SHENG SAA 1850MM 3P CONN. BLACK
Australia
MKC13
6410BK21004
213356-001 LINE TEK SAA 1830MM 3PIN CONN. BLACK
Australia
92
REMARKS
For refresh
model
Germany,Iran,
Portugal,Spain
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKC13
6410BK21002
213356-001 VOLEX SAA 1830MM 3PIN CONN. BLACK
Australia
MKC13
6410BK20705
PL8B1SQJ10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BK21007
SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK
Australia
MKC13
6410BK21006
AU10S3+H03VV-F+VAC5S VOLEX SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BX21601
SP-022+IS-034+H05VV-F3G I-SHENG GOST 1800MM 3P CONN. BLACK
Russia
MKC13
6410BX21602
PF8B1CIJ10A-060 LONGWELL GOST 1830MM 3PIN CONN. BLACK
Russia
MKC13
6410BD21602
PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK
Spain
MKC13
6410BD20308
213350-001 LINE TEK VDE/SEMKO 1830MM 3PIN CONN. BLACK
Spain
MKC13
6410BD20306
213350-001 VOLEX VDE/SEMKO 1830MM 3P CONN. BLACK
Spain
MKC13
6410BW21001
X-LGPC0415-001 VOLEX ISI 1830MM 3PIN CONN. BLACK
India
MKC13
6410BQ21002
BR10S3+H03VV-F+VAC5S VOLEX INMETRO 1830MM 3PIN CONN BLACK
Brazil
MKC13
6410BQ21003
SP-305+H05VV-F+IS-034 I-SHENG INMETRO 1830MM 3PIN CONN BLACK
Brazil
MKC13
6410BO20603
P48F1SAJ30A-060 LONGWELL CCC 1830MM 3P CONN BLACK
China
MKC13
6410BO20602
SP-506+RVV 3CX0.75MM2+IS-034 I-SHENG CCC 1830MM 3P CONN BLACK
China
MKC13
6410BO21008
GB10S3+RW300_300+VAC5S VOLEX CCC 1830MM 3PIN CONN BLACK
China
MKC13
6410BH21003
SP-60+IS-034 I-SHENG BSI 1830MM 3PIN CONN FOR NT-PC BLACK
MKC13
6410BV21002
PF8B1L1J10A-060 LONGWELL SII 1830MM 3PIN CONN. BLACK
Israel
MKC13
6410BV21003
SP-86+IS-034 I-SHENG SII 1830MM 3PIN CONN. BLACK
Israel
MKC13
6410BU21602
SP-80A+H05VV-F+IS-034 I-SHENG SABS 1830MM 3PIN CONN BLACK
MKH02
3301B00525A
HDD PLATE ASSY
MKH03
3110BM3021A
HDD CASE 2 TONE 14.1"
MKH03
3110BM2033A
HDD CASE 2 TONE 15.0"
MKH04
6744C00085A
HDD, FUJITSU MHT2040AT 40GB EIDE
MKH04
6744C00068A
HDD, TOSHIBA MK4021GAS40GB EIDE
MKH04
6744C00105A
HDD, HGST IC25N040ATMR04-0 40GB EIDE
MKH04
6744C00086A
HDD, FUJITSU MHT2060AT 60GB EIDE
MKH04
6744C00069A
HDD, TOSHIBA MK6021GAS 60GB EIDE
MKH04
6744C00106A
HDD, HGST IC25N060ATMR04-0 60GB EIDE
MKH04
6744C00087A
HDD, FUJITSU MHT2080AT 80GB EIDE
MKH04
6744C00090A
HDD, TOSHIBA MK8025GAS 80GB EIDE
MKH04
6744C00107A
HDD, HGST IC25N080ATMR04-0 80GB EIDE
MKS01
6871BG824AA
MCKINLEY LGE 4 LAYERS REV 0.4 PCMCIA WSD 15.0" SUB B/D ASSY
93
REMARKS
UAE,Saudi
Arabia
South Africa
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKS01
6871BG854AA
MCKINLEY N . . LGE 4 LAYERS REV 0.2 MCKINLEY REFRESH 15.0" PCMCIA 7420
SUB B/D MAIN ASSY
MKS02
6871BG821AA
MCKINLEY LGE 4 LAYERS REV 0.4 PCMCIA WSD 14.1" SUB B/D ASSY
MKS02
6871BG851AA
MCKINLEY N . . LGE 4 LAYERS REV 0.2 MCKINLEY REFRESH 14.1" PCMCIA 7420
SUB B/D MAIN ASSY
MKS03
6871BJ320AB
MCKINLEY WIMTEC 2 LAYERS REV 0.4 SVIDEO, USB 15.0" SUB ASSY
MKS04
6871BJ320AA
MCKINLEY WIMTEC 2 LAYERS REV 0.4 SVIDEO, USB SUB 14.1" B/D ASSY
MKS05
6871BJ350AA
MCKINLEY WIMTEC 2 LAYERS REV 0.3 ODD I/F SUB B/D ASSY
MKS06
6871BJ300AA
MCKINLEY WIMTEC 2 LAYERS REV 0.3 NETWORK, PWR SUB B/D ASSY
MKS06
6871BJ300AB
MCKINLEY LG-IBM N N WIMTEC 2 LAYERS REV 0.4 NETWORK, PWR SUB B/D
ASSY
MKD01
3111BZ8801A
KBD DECK ASSY 15.0"
MKD01
3111BZ8801B
N N KBD DECK ASSY 15" MCKINLEY KBD DECK W/ UV COATED KNOB
MKD01
3111BZ8800A
KBD DECK ASSY 14.1"
MKD01
3111BZ8801D
MCKINLEY N N MCKINLEY KBD DECK TOTAL ASSY 15.0" FOR MC REFRESH
For refresh
model
MKD01
3111BZ8800C
MCKINLEY N N MCKINLEY KBD DECK TOTAL ASSY 14.1" FOR MC REFRESH
For refresh
model
MKD03
6401B10002A
SPEAKER ASSY, ESTEC A252SX-012K14 0.8W 4PIN 166.5X27MM 8OHM 75DB
MKD04
6871BJ340AA
MCKINLEY WIMTEC 2 LAYERS REV 0.3 TOUCHPAD (15.0") SUB B/D ASSY
MKD04
6871BJ330AA
MCKINLEY WIMTEC 2 LAYERS REV 0.3 TOUCHPAD (14.1") SUB B/D ASSY
MKM01
3111BZ9901A
MCKINLEY BOTTOM CASE ASSY 15.0"
MKM01
3111BZ9901C
MCKINLEY N N MCKINLEY BOTTOM FOR MC REFRESH 15.0"
MKM02
3111BZ9900A
MCKINLEY BOTTOM CASE ASSY 14.1"
MKM02
3111BZ9900B
GIRAFFE BOTTOM ASSY 14.1" ONLY PCMCIA W/ PAINT, SUB PARTS
MKM02
3111BZ9900C
MCKINLEY N N MCKINLEY BOTTOM FOR MC REFRESH 14.1""
MKM03
3210BD2014A
FRAME, HINGE & BATTERY 14.1"
MKM04
3210BD1005A
FRAME, HINGE & BATTERY 15.0"
MKM05
3581BZ0030A
COVER, ASSY DDR MEMORY
MKM06
3551B03007B
RETAINER ASSY 15.0" WITH SUB B/D
MKM07
3551BZ3004B
RETAINER ASSY 14.1" WITH SUB B/D
94
REMARKS
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
For refresh
model
Ch6. Part lists
Location
LG P/N
SPECIFICATION
MKM08
3550BM3173B
COVER, CLUTCH LEFT
MKM09
3550BM3172A
COVER, CLUTCH RIGHT
MKM10
3550BM3171A
DUMMY, PCMCIA
MKM11
3550BM4047A
DUMMY, SD
MKM12
3301BZ9092D
PLATE, CHIPSET COVER ASSY 15.0" M9
MKM12
3301BZ9092A
PLATE, CHIPSET COVER ASSY 14.1" M9
MKM12
3301BZ9092B
PLATE, CHIPSET COVER ASSY 15.0" M10
MKM12
3301BZ9092C
PLATE, CHIPSET COVER ASSY 14.1" M10
MKM16
5022BZ4025A
THERMAL PAD 19X19 MM ON FAN
MKM17
5022BP4010A
THERMAL PAD 15X25 MM ON ATI
MKM18
5022BP4010B
THERMAL PAD 11X11 MM ON NORTHBRIDGE
MKM19
1SZZBA4017B
SCREW, D2.0 M2.0 L 3.5 MM TORQUE 2.0 0.2
MKM21
1SZZBA4068A
SCREW, D4.5 M2.5 L5.0 MM TORQUE 2.0 0.2
MKM22
1SZZBA4044B
SCREW, D4.5 M2.5 L4.0 MM TORQUE 2.0 0.2
MKM23
1SZZBZ3009B
SCREW, D3.8 M2.0 L 2.5 MM TORQUE 2.0 0.2
MKM27
1SZZBA4011F
SCREW, D5.5 M3.0 L3.5 MM TORQUE 2.0 0.2
MKM28
1SZZBA4067A
SCREW, D4.0 M2.0 L13.0 MM TORQUE 2.0 0.2
MKM29
1SZZBZ4020A
SCREW, D4.0 M2.0 L8.8 MM TORQUE 1.5 0.2
MKM30
1SZZBA4039B
SCREW, D4.5 M2.5 L8.0 MM TORQUE 3.0 0.2
MKM31
1SZZBZ4018B
SCREW, D3.8 M2.0 L2.0 MM TORQUE 1.5 0.2
MKM32
1SZZBZ4014A
SCREW, D4.3 M2.0 L5.0 MM TORQUE 2.0 0.2
MKM33
1SZZBA4083A
SCREW, D3.8 M2.0 L8.0 MM TORQUE 2.0 0.2
MKM34
1SZZBA4085A
SCREW, D5.5 M3.0 L6.0 MM TORQUE 2.0 0.2
MKM39
1SZZBA4017A
SCREW, D2.0 L3.0 MM TORQUE 2.0 0.2
MKM38
4986BZ4117A
GASKET ON MINI-PCI ANTENNA CONNECTOR
95
REMARKS
Case : LCD 14.1"
MKL27
MKL29
MKL22
MKL23
MKL31
MKL28
MKL15
Case : LCD 14.1"
Location
LG P/N
SPECIFICATION
MKL15
3858BZ3019A INSULATOR, INVERTER 14.1"/15.0"
MKL22
3680BM3036A LENS, WIRELESS REAR 14.1"
MKL23
3550BM1149B DECORATION COVER, 14.1" FOR EXPORT
MKL27
3858BZ3020A INSULATOR, LED 14.1"
MKL28
3110BD0008B REAR CASE, 14.1" FOR EXPORT
MKL28
3110BD0008D MCKINLEY MG DISPLAY REAR 14.1" FOR MC REFRESH
MKL29
6871BZT16ZA CABLE FPC, WIRELESS INDICATOR 14.1"
MKL31
3858BZ4450B MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG
96
REMARKS
For refresh model
For refresh model
Case : LCD 15.0"
MKL12
MKM23
MKL17
MKL31
MKL15
MKL14
Case : LCD 15.0"
Location
LG P/N
SPECIFICATION
MKL12
6871BZT17AA CABLE FPC, WIRELESS INDICATOR 15.1"
MKL14
3110BD0009B REAR CASE, 15.0" FOR EXPORT
MKL14
3110BD0009D MCKINLEY MG DISPLAY REAR 15.0" FOR MC REFRESH
MKL15
3858BZ3019A INSULATOR, INVERTER 14.1"/15.0"
MKL17
3550BM2093B DECORATION COVER, 15.0" FOR EXPORT
MKL23
3550BM1149B DECORATION COVER, 14.1" FOR EXPORT
MKL31
3858BZ4450B MCKINLEY N N N MCKINLEY BADGE FOR EXPORT LG
97
REMARKS
For refresh model
For refresh model
MKM22
MKM22
MKL16
MKM23
MKL06
MKL05
MKL04
MKL18
MKM23
MKL13
MKM23
MKL24(14.1")
MKL09(15.0")
MKL20(14.1")
MKL02(15.0")
MKM23
MKL11(15.0")
MKL26(14.1")
MKL25(14.1")
MKL10(15.0")
98
Location
LG P/N
SPECIFICATION
MKL02
6304FLP081A TFT LCD, LG PHILIPS LP150E06-A2 15.0 INCH SXGA+
MKL02
6304FLP080A TFT LCD, LG PHILIPS LP150X08-A3M1 15.0 INCH XGA
MKL02
6304FAU002B TFT LCD, AU B150XG01 15.0 INCH XGA
MKL02
6304FBH005A TFT LCD, BOE-HYDIS HT15X34-100 15.0 INCH XGA
MKL04
4940BM4146A KNOB, LATCH
MKL05
4026BM3013A LATCH, DISPLAY
MKL06
4970BW4540A SPRING, LCD LATCH
MKL09
4775B00033A HINGE ASSY, LEFT 15.0"
MKL10
4775B00034A HINGE ASSY, RIGHT 15.0"
MKL11
6851B76028A CABLE ASSY, LCD 15.0"
MKL13
6708BI0082A
INVERTER, ALPS KUBNKM063A
MKL13
6708BI0083A
INVERTER, DELTA DAC-08B043A
MKL16
3301BZ0512B ANTENNA, WIRELESS RIGHT
MKL18
3301BZ0513B ANTENNA, WIRELESS LEFT
MKL20
6304FBH004A TFT LCD, BOE HYDIS HT14X1B-110 14.1 INCH XGA
MKL20
6304FLP079A TFT LCD, LG PHILIPS LP141X13-C2 14.1 INCH XGA
MKL20
6304FLP079B LP141X13-C2K1 LG PHILPS TFT COLOR 14.1 INCH XGA(1024X768) ISP STYLE B
MKL24
4775BZ1004A HINGE ASSY, LEFT 14.1"
MKL25
4775BZ1005A HINGE ASSY, RIGHT 14.1"
MKL26
6851B76024A CABLE ASSY, LCD 14.1"
MKM22
1SZZBA4044B SCREW, D4.5 M2.5 L4.0 MM TORQUE 2.0
0.2
MKM23
1SZZBZ3009B SCREW, D3.8 M2.0 L 2.5 MM TORQUE 2.0
0.2
99
REMARKS
MKL07
MKL07
MKM22
MKL07
MKL07
MKM22
MKL08
MKM21
MKL21(14.1")
MKL03(15.0")
MKM22
MKL08
MKL30
MKM21
Location
LG P/N
SPECIFICATION
REMARKS
MKL03
3111BZ7101A CASE ASSY, FRONT 15.0
MKL07
4850BM4010A CUSHION, RUBBER UPPER
MKL08
4850BM4011A CUSHION, RUBBER LOWER
MKL21
3111BZ7100A CASE ASSY, FRONT 14.1"
MKL30
3850BB3035D MODEL NAME LABEL, MCKINLEY 14.1" FOR EXPORT
MKL30
3850BB3035E MODEL NAME LABEL, MCKINLEY 15.0" FOR EXPORT
MKL30
3850BB3035P MCKINLEY N N MODEL NAME LABEL 14.1" MCKINLEY LM40A
FOR REFRESH EXPORT
For refresh model
MKL30
3850BB3035Q MCKINLEY N N MODEL NAME LABEL 15" MCKINLEY LM50A
FOR REFRESH EXPORT
For refresh model
MKM21
1SZZBA4068A SCREW, D4.5 M2.5 L5.0 MM TORQUE 2.0
0.2
MKM22
1SZZBA4044B SCREW, D4.5 M2.5 L4.0 MM TORQUE 2.0
0.2
100
MKM32
MKM38
MDC
Modem
MKB01
MKC04
MKC05
MKM19
MKC04
Mini
PCI
MKM19
Cardbus
MKM19
MKS03(15.0")
MKS04(14.1")
MKS02(14.1")
MKS01(15.0")
MKM02(14.1")
MKM01(15.0")
MKC12
MKS06
MKM19
MKM03(14.1")
MKM04(15.0")
101
Location
LG P/N
SPECIFICATION
MKB01
6871BF100A1 MAINBOARD ASSY, BH M9+ P.P LGE 8 LAYERS REV 0.5
MKB01
6871BF200A1 MAINBOARD ASSY, BH M10 P.P LGE 8 LAYERS REV 0.5
MKB01
6871BF300A1 MCKINLEY US007506 REFRESH MODEL . LGE 8 LAYERS REV 0.7 M11
MAINSTEAM MAIN ASSY
MKC04
6871BZT13A4 WIRELESS LAN, INTEL WM3B2100WW MINI-PCI TYPE IIIB
MKC04
6871BZT14A4 MCKINLEY N WM3B2200BGRW PRO/WIRELESS2200BG LAN MINI-PCI
TYPE INTEL 4 LAYERS 1-14 NETWORK CONNECTION
MKC04
6871BZT13A5 WM3B2100NA1 MINI-PCI TYPE IIIB INTEL 4 LAYERS 1-11 PRO/WIRELESS2100
LAN MINI-PCI TYPE 3B ADAPTER LIO
MKC05
6871BG105AA MDC MODEM, AMBIT T60M283.13 56K
MKC12
6910C00007A RTC BATTERY, MINAMOTO CR2032 3.0 VOLT 210MAH
MKC12
6910C00005A RTC BATTERY, SONY CR2032 3.0 VOLT 200MA
MKM01
3111BZ9901A MCKINLEY BOTTOM CASE ASSY 15.0"
MKM01
3111BZ9901C MCKINLEY N N MCKINLEY BOTTOM FOR MC REFRESH 15.0"
MKM02
3111BZ9900A MCKINLEY BOTTOM CASE ASSY 14.1"
MKM02
3111BZ9900B GIRAFFE BOTTOM ASSY 14.1" ONLY PCMCIA W/ PAINT, SUB PARTS
MKM02
3111BZ9900C MCKINLEY N N MCKINLEY BOTTOM FOR MC REFRESH 14.1"
MKM03
3210BD2014A FRAME, HINGE & BATTERY 14.1"
MKM04
3210BD1005A FRAME, HINGE & BATTERY 15.0"
MKM19
1SZZBA4017B SCREW, D2.0 M2.0 L 3.5 MM TORQUE 2.0
0.2
MKM32
1SZZBZ4014A SCREW, D4.3 M2.0 L5.0 MM TORQUE 2.0
0.2
MKM38
4986BZ4117A GASKET ON MINI-PCI ANTENNA CONNECTOR
MKS01
6871BG824AA MCKINLEY LGE 4 LAYERS REV 0.4 PCMCIA WSD 15.0" SUB B/D ASSY
MKS01
6871BG854AA MCKINLEY N . . LGE 4 LAYERS REV 0.2 MCKINLEY REFRESH 15.0"
PCMCIA 7420 SUB B/D MAIN ASSY
MKS02
6871BG821AA MCKINLEY LGE 4 LAYERS REV 0.4 PCMCIA WSD 14.1" SUB B/D ASSY
MKS02
6871BG851AA MCKINLEY N . . LGE 4 LAYERS REV 0.2 MCKINLEY REFRESH 14.1"
PCMCIA 7420 SUB B/D MAIN ASSY
MKS03
6871BJ320AB MCKINLEY WIMTEC 2 LAYERS REV 0.4 SVIDEO, USB 15.0" SUB ASSY
MKS04
6871BJ320AA MCKINLEY WIMTEC 2 LAYERS REV 0.4 SVIDEO, USB SUB 14.1" B/D ASSY
MKS06
6871BJ300AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 NETWORK, PWR SUB B/D ASSY
MKS06
6871BJ300AB MCKINLEY LG-IBM N N WIMTEC 2 LAYERS REV 0.4 NETWORK,
PWR SUB B/D ASSY
102
REMARKS
For refresh model
For refresh model
USA,Canada,
Taiwan
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
MKM23(14 )
MKM32(15 )
MKM12
MKM38
14 M9 : 3301BZ9092A
M10 : 3301BZ9092C
15 M9 : 3301BZ9092D
M10 : 3301BZ9092B
MKM29
MKC07
MKC10
MKS05
MKC02
MKM19
15 ODD I/F
MKM17 MKM18
MKH04
MKM16
MKH02
MKM27
MKM27
MKH03
103
Location
LG P/N
SPECIFICATION
MKC02
2029BG0100A DVD/CDRW COMBO, TOSHIBA SD-R9012 8X 16X 8X 24X BUILT IN 9.5 MM
MKC02
6777BG0001A DVD, TEAC DV-28E-BC-43 8X 24X BUILT IN 9.5 MM
MKC07
5901B09265A FAN ASSY, W/ SHEET
MKC10
0IMCRIN103B PROCESSOR, INTEL RH80535GC0131M 478P UFCPGA PENTIUM-M
1300MHZ/600MHZ B1-STEPPING(SL6N4)
MKC10
0IMCRIN104B PROCESSOR, INTEL RH80535GC0171M 478P UFCPGA PENTIUM-M
1400MHZ/600MHZ B1-STEPPING(SL6F8)
MKC10
0IMCRIN105B PROCESSOR, INTEL RH80535GC0211M 478P UFCPGA PENTIUM-M
1500MHZ/600MHZ B1-STEPPING(SL6F9)
MKC10
0IMCRIN106B PROCESSOR, INTEL RH80535GC0251M 478P UFCPGA PENTIUM-M
1600MHZ/600MHZ B1-STEPPING(SL6FA)
MKC10
0IMCRIN119A PROCESSOR, INTEL RH80535GC0291M 478P UFCPGA PENTIUM-M
1700MHZ/600MHZ B1-STEPPING(SL6N5)
MKC10
0IMCRIN150A RH80535NC009512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1200MHZ/400MHZ B1-STEPPING(SL79S)
MKC10
0IMCRIN132A RH80535NC013512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1300MHZ/400MHZ B1-STEPPING(SL6N7)
MKC10
0IMCRIN133A RH80535NC017512 LG INTEL 478P UFCPGA TRAY NT CPU CELERON-M
1400MHZ/400MHZ B1-STEPPING(SL6N6)
MKH02
3301B00525A HDD PLATE ASSY
MKH03
3110BM3021A HDD CASE 2 TONE 14.1"
MKH03
3110BM2033A HDD CASE 2 TONE 15.0"
MKH04
6744C00085A HDD, FUJITSU MHT2040AT 40GB EIDE
MKH04
6744C00068A HDD, TOSHIBA MK4021GAS40GB EIDE
MKH04
6744C00105A HDD, HGST IC25N040ATMR04-0 40GB EIDE
MKH04
6744C00086A HDD, FUJITSU MHT2060AT 60GB EIDE
MKH04
6744C00069A HDD, TOSHIBA MK6021GAS 60GB EIDE
MKH04
6744C00106A HDD, HGST IC25N060ATMR04-0 60GB EIDE
MKH04
6744C00087A HDD, FUJITSU MHT2080AT 80GB EIDE
MKH04
6744C00090A HDD, TOSHIBA MK8025GAS 80GB EIDE
MKH04
6744C00107A HDD, HGST IC25N080ATMR04-0 80GB EIDE
104
REMARKS
Location
LG P/N
SPECIFICATION
MKM12
3301BZ9092D PLATE, CHIPSET COVER ASSY 15.0" M9
MKM12
3301BZ9092A PLATE, CHIPSET COVER ASSY 14.1" M9
MKM12
3301BZ9092B PLATE, CHIPSET COVER ASSY 15.0" M10
MKM12
301BZ9092C
MKM16
5022BZ4025A THERMAL PAD 19X19 MM ON FAN
MKM17
5022BP4010A THERMAL PAD 15X25 MM ON ATI
MKM18
5022BP4010B THERMAL PAD 11X11 MM ON NORTHBRIDGE
MKM19
1SZZBA4017B SCREW, D2.0 M2.0 L 3.5 MM TORQUE 2.0
0.2
MKM23
1SZZBZ3009B SCREW, D3.8 M2.0 L 2.5 MM TORQUE 2.0
0.2
MKM27
1SZZBA4011F SCREW, D5.5 M3.0 L3.5 MM TORQUE 2.0
0.2
MKM29
1SZZBZ4020A SCREW, D4.0 M2.0 L8.8 MM TORQUE 1.5
0.2
MKM32
1SZZBZ4014A SCREW, D4.3 M2.0 L5.0 MM TORQUE 2.0
0.2
MKM38
4986BZ4117A GASKET ON MINI-PCI ANTENNA CONNECTOR
MKS05
6871BJ350AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 ODD I/F SUB B/D ASSY
PLATE, CHIPSET COVER ASSY 14.1" M10
105
REMARKS
MKM31
MKM32
MKM33
ODD
MKD01
MKM39
MKD03
MKD04
106
Location
LG P/N
SPECIFICATION
REMARKS
MKD01
3111BZ8801A KBD DECK ASSY 15.0"
MKD01
3111BZ8801B N N KBD DECK ASSY 15" MCKINLEY KBD DECK W/ UV COATED KNOB
MKD01
3111BZ8800A KBD DECK ASSY 14.1"
MKD01
3111BZ8801D MCKINLEY N N MCKINLEY KBD DECK TOTAL ASSY 15.0" FOR MC REFRESH
For refresh model
MKD01
3111BZ8800C MCKINLEY N N MCKINLEY KBD DECK TOTAL ASSY 14.1" FOR MC REFRESH
For refresh model
MKD03
6401B10002A SPEAKER ASSY, ESTEC A252SX-012K14 0.8W 4PIN 166.5X27MM 8OHM 75DB
MKD04
6871BJ340AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 TOUCHPAD (15.0") SUB B/D ASSY
MKD04
6871BJ330AA MCKINLEY WIMTEC 2 LAYERS REV 0.3 TOUCHPAD (14.1") SUB B/D ASSY
MKM31
1SZZBZ4018B SCREW, D3.8 M2.0 L2.0 MM TORQUE 1.5
0.2
MKM32
1SZZBZ4014A SCREW, D4.3 M2.0 L5.0 MM TORQUE 2.0
0.2
MKM33
1SZZBA4083A SCREW, D3.8 M2.0 L8.0 MM TORQUE 2.0
0.2
MKM39
1SZZBA4017A SCREW, D2.0 L3.0 MM TORQUE 2.0
107
0.2
For refresh model
MKC08
MKM32
MKM06(15.0")
MKM07(14.1")
MKM08
MKM30
MKM32
MKM09
MKM30
MKM10
MKM11
108
Location
LG P/N
SPECIFICATION
REMARKS
MKC08
3823B70004A MCKINLEY LG-IBM SUNREX-K021102A US-ENG 14.1" 84 KEY
MKC08
3823B71004A MCKINLEY LG-IBM SUNREX US-ENG LM REFRESH 14"
MKC08
3823B70004C MCKINLEY LG-IBM SUNREX-K021102A RUSSIAN 14.1" 84 KEY
MKC08
3823B71004C MCKINLEY LG-IBM SUNREX RUSSIAN LM REFRESH 14"
MKC08
3823B70004D MCKINLEY LG-IBM SUNREX K021167 ARABIAN 14.1" 84 KEY
MKC08
3823B71004D MCKINLEY LG-IBM SUNREX ARAB LM EFRESH 14"
MKC08
3823B70004E MCKINLEY LG-IBM SUNREX K021167 HEBREW 14.1" 84 KEY
MKC08
3823B71004E MCKINLEY LG-IBM SUNREX HEBREW LM REFRESH 14"
MKC08
3823B70004F MCKINLEY LG-IBM SUNREX K021167 FARSI(IRAN) 14.1" 84 KEY
MKC08
3823B71004F MCKINLEY LG-IBM SUNREX FARSI LM REFRESH 14"
MKC08
3823B70004H MCKINLEY LG-IBM SUNREX K021167 US SOUTH AFRICA 14.1" 84 KEY
MKC08
3823B71004H MCKINLEY LG-IBM SUNREX US SOUTH AFRICA LM REFRESH 14"
MKC08
3823B70004G MCKINLEY LG-IBM SUNREX K021167 UKRAINIAN 14.1" 84 KEY
MKC08
3823B71004G MCKINLEY N SUNREX UKRAINIAN LM REFRESH 14"
MKC08
3823B70004K MCKINLEY LG-IBM SUNREX K021167 SPANISH 14.1" 84KEY
MKC08
3823B70004J MCKINLEY LG-IBM SUNREX K021167 PORTUGUESE 14.1" 84 KEY
MKC08
3823B70004L MCKINLEY LG-IBM SUNREX K021167 POLISH 14.1" 84KEY
MKC08
3823B71004L MCKINLEY LG-IBM SUNREX POLISH LM REFRESH 14"
MKC08
3823B70004M MCKINLEY N SUNREX K021167 FRENCH 14.1" 84KEY
MKC08
3823B71004M MCKINLEY LG-IBM SUNREX FRENCH REFRESH LM 14"
MKC08
3823B70004N MCKINLEY N SUNREX THAILAND 14" 84KEY
MKC08
3823B71004N MCKINLEY N SUNREX THAILAND LM REFRESH 14"
MKC08
3823B70004P MCKINLEY LG-IBM SUNREX TAIWAN 14.1" 84KEY
MKC08
3823B71004P MCKINLEY N SUNREX TAIWAN LM REFRESH 14"
For refresh model
MKC08
3823B71004Q MCKINLEY N SUNREX HUNGARY REFRESH LM 14"
For refresh model
MKC08
3823B71004R MCKINLEY N SUNREX CZECH LM REFRESH 14"
For refresh model
MKC08
3823B71004S MCKINLEY N SUNREX TURKEY REFRESH LM 14"
For refresh model
MKC08
3823B70008A MCKINLEY LG-IBM OKI US-ENG 15" 86 KEY
MKC08
3823B71008A MCKINLEY LG-IBM OKI US LM REFRESH 15"
MKC08
3823B70008C MCKINLEY LG-IBM OKI RUSSIAN 15" 86 KEY
MKC08
3823B71008C MCKINLEY LG-IBM OKI RUSSIAN LM REFRESH 15"
MKC08
3823B70008D MCKINLEY LG-IBM OKI ARABIAN 15" 86 KEY
MKC08
3823B71008D MCKINLEY LG-IBM OKI ARAB LM REFRESH 15"
MKC08
3823B70008E MCKINLEY LG-IBM SUNREX-K020346A HEBREW 15" 86 KEY
MKC08
3823B71008E MCKINLEY LG-IBM OKI HEBREW LM REFRESH 15"
MKC08
3823B70008F MCKINLEY LG-IBM OKI FARSI 15" 86 KEY
109
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
Location
LG P/N
SPECIFICATION
REMARKS
MKC08
3823B71008F MCKINLEY LG-IBM OKI FARSI LM REFRESH 15"
MKC08
3823B70008H MCKINLEY LG-IBM OKI US SOUTH AFRICA 15" 86KEY
MKC08
3823B71008H MCKINLEY LG-IBM OKI US SOUTH AFRICA LM REFRESH 15"
MKC08
3823B70008G MCKINLEY LG-IBM OKI UKRAINAIN 15" 86 KEY
MKC08
3823B71008G MCKINLEY N OKI UKRAINAIN LM REFRESH 15"
MKC08
3823B70008K MCKINLEY LG-IBM OKI SPANISH 15" 86KEY
MKC08
3823B70008J MCKINLEY LG-IBM OKI PORTUGUESE 15" 86KEY
MKC08
3823B70008L MCKINLEY LG-IBM OKI POLISH 15" 87KEY
MKC08
3823B71008L MCKINLEY LG-IBM OKI POLISH LM REFRESH 15"
MKC08
3823B70008M MCKINLEY N OKI FRENCH 15" 87KEY
MKC08
3823B71008M MCKINLEY LG-IBM OKI FRENCH REFRESH LM 15"
MKC08
3823B70008N MCKINLEY LG-IBM SUNREX THAILAND 15" LM 84KEY
MKC08
3823B71008N MCKINLEY N OKI THAILAND LM REFRESH 15"
MKC08
3823B70008P MCKINLEY LG-IBM OKI TAIWAN 15" LM 86KEY
MKC08
3823B71008P MCKINLEY N OKI TAIWAN LM REFRESH 15"
For refresh model
MKC08
3823B71008Q MCKINLEY N OKI HUNGARY LM REFRESH 15"
For refresh model
MKC08
3823B71008R MCKINLEY N OKI CZECH LM REFRESH 15"
For refresh model
MKC08
3823B71008S MCKINLEY N OKI TURKEY LM REFRESH 15"
For refresh model
MKM06
3551B03007B RETAINER ASSY 15.0" WITH SUB B/D
MKM07
3551BZ3004B RETAINER ASSY 14.1" WITH SUB B/D
MKM08
3550BM3173B COVER, CLUTCH LEFT
MKM09
3550BM3172A COVER, CLUTCH RIGHT
MKM10
3550BM3171A DUMMY, PCMCIA
MKM11
3550BM4047A DUMMY, SD
MKM30
1SZZBA4039B SCREW, D4.5 M2.5 L8.0 MM TORQUE 3.0
0.2
MKM32
1SZZBZ4014A SCREW, D4.3 M2.0 L5.0 MM TORQUE 2.0
0.2
110
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
For refresh model
MKM30
MKM05
MKC06
MKM33
MKM33
MKM30
MKM28
MKM33
MKC01
MKM33
MKM34
MKM19
MKC11
MKC13
111
Location
LG P/N
SPECIFICATION
REMARKS
MKC01
0IMMRSS090A MEMORY, SAMSUNG M470L3224FT0-CB3 SODIMM 256MB DDR 333MHZ
MKC01
0IMMRHY044A MEMORY, HYNIX HYMD232M646C6-J SODIMM 256MB DDR 333MHZ
MKC01
0IMMRIH032A MEMORY, INFINEON HYS64D32020GDL-6-B SODIMM 256MB DDR 333MHZ
MKC01
0IMMRSS091A MEMORY, SAMSUNG M470L6423EN0-CB3 SODIMM 512MB DDR 333MHZ
MKC01
0IMMRIH033A MEMORY, INFINEON HYS64D64020GBDL-6-B SODIMM 512MB DDR 333MHZ
MKC06
6911BZ0045B LI-ION BATTERY, SIMPLO 4400MAH 3S-2P
MKC06
6911BZ0046B LI-ION BATTERY, SIMPLO 6600MAH 3S-3P
MKC11
6708BA0036B ADAPTER, LITEON PA-1650-02L1 65W 18.5V/3.5A 3PIN
MKC11
6708BA0044B ADAPTER, HIPRO HP-OK065B133 65W 16V/3.5A 3PIN
MKC13
6410BD21003 PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK
MKC13
6410BK21005 PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BK20704 213356-001(SP502A+IS34) I-SHENG SAA 1850MM 3P CONN. BLACK
Australia
MKC13
6410BK21004 213356-001 LINE TEK SAA 1830MM 3PIN CONN. BLACK
Australia
MKC13
6410BK21002 213356-001 VOLEX SAA 1830MM 3PIN CONN. BLACK
Australia
MKC13
6410BK20705 PL8B1SQJ10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BK21007 SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK
Australia
MKC13
6410BK21006 AU10S3+H03VV-F+VAC5S VOLEX SAA 1830MM 3PIN CONN BLACK
Australia
MKC13
6410BX21601 SP-022+IS-034+H05VV-F3G I-SHENG GOST 1800MM 3P CONN. BLACK
Russia
MKC13
6410BX21602 PF8B1CIJ10A-060 LONGWELL GOST 1830MM 3PIN CONN. BLACK
Russia
MKC13
6410BD21602 PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK
Spain
MKC13
6410BD20308 213350-001 LINE TEK VDE/SEMKO 1830MM 3PIN CONN. BLACK
Spain
MKC13
6410BD20306 213350-001 VOLEX VDE/SEMKO 1830MM 3P CONN. BLACK
Spain
MKC13
6410BW21001 X-LGPC0415-001 VOLEX ISI 1830MM 3PIN CONN. BLACK
India
MKC13
6410BQ21002 BR10S3+H03VV-F+VAC5S VOLEX INMETRO 1830MM 3PIN CONN BLACK
Brazil
MKC13
6410BQ21003 SP-305+H05VV-F+IS-034 I-SHENG INMETRO 1830MM 3PIN CONN BLACK
Brazil
MKC13
6410BO20603 P48F1SAJ30A-060 LONGWELL CCC 1830MM 3P CONN BLACK
China
MKC13
6410BO20602 SP-506+RVV 3CX0.75MM2+IS-034 I-SHENG CCC 1830MM 3P CONN BLACK
China
MKC13
6410BO21008 GB10S3+RW300_300+VAC5S VOLEX CCC 1830MM 3PIN CONN BLACK
China
MKC13
6410BH21003 SP-60+IS-034 I-SHENG BSI 1830MM 3PIN CONN FOR NT-PC BLACK
MKC13
6410BV21002 PF8B1L1J10A-060 LONGWELL SII 1830MM 3PIN CONN. BLACK
Israel
MKC13
6410BV21003 SP-86+IS-034 I-SHENG SII 1830MM 3PIN CONN. BLACK
Israel
MKC13
6410BU21602 SP-80A+H05VV-F+IS-034 I-SHENG SABS 1830MM 3PIN CONN BLACK
112
Germany,Iran,
Portugal,Spain
UAE,Saudi Arabia
South Africa
Location
LG P/N
SPECIFICATION
MKM05
3581BZ0030A COVER, ASSY DDR MEMORY
MKM19
1SZZBA4017B SCREW, D2.0 M2.0 L 3.5 MM TORQUE 2.0
0.2
MKM28
1SZZBA4067A SCREW, D4.0 M2.0 L13.0 MM TORQUE 2.0
0.2
MKM30
1SZZBA4039B SCREW, D4.5 M2.5 L8.0 MM TORQUE 3.0
0.2
MKM33
1SZZBA4083A SCREW, D3.8 M2.0 L8.0 MM TORQUE 2.0
0.2
MKM34
1SZZBA4085A SCREW, D5.5 M3.0 L6.0 MM TORQUE 2.0
0.2
113
REMARKS
Download PDF

advertising