LG LP-XG2 projector Owner's manual
Below you will find brief information for projector LP-XG2. The LP-XG2 is a projector that can display images at a resolution of 1024x768 pixels. It can be used to display images from a variety of sources, including computers, video players, and camcorders. The projector also has a variety of functions, including zoom, resize, and auto tracking, which allow you to adjust the image to your liking.
Advertisement
Advertisement
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the bottom of the set and quote this information to your dealer when you require service.
Model number :
Serial number :
LP-XG2
OWNER’S MANUAL
1
CONTENTS
Before operating the unit, please read this manual carefully.
INTRODUCTION
Safety Instructions
Names of parts
3
7
INSTALLATION AND
CONNECTION
Installation and Connection
Connecting to a Desktop PC
11
15
Connecting to a Notebook PC 16
Connecting to a Macintosh Desktop PC 17
Connecting to a Macintosh PowerBook 20
Connecting to a Video Source 21
BASIC FUNC-
TIONS
Turning on the Projector
Operating the Projector
Function checking
Selecting source mode
Using Still function
22
23
25
26
27
SPECIAL
FUNCTIONS
Selecting language 28
Using Flip Horizontal / Vertical function 29
Using Blank function 31
Checking lamp time
Selecting PC screen size input signal
33
34
POSITIONING
Adjusting screen display
Using Resize function
VIDEO/
TRACKING
Adjusting Video
Using Tracking function
INFORMATION
Supported Monitor Display
Maintenance
Specifications
35
37
38
39
41
42
44
2
Safety Instructions
G Always keep the safety instructions to prevent any potential accident or misuse of the projector.
G
Safety Instructions have two kinds of information, and each meaning of it is as below.
WARNING
The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the projector.
✶ The meanings of symbols in the manual and the unit are as below.
G
Take care of danger that may happen under specific condition.
G
Take care of electric shock that may happen under specific condition.
G
After reading this manual, keep it in the place that the user always can contact easily.
WARNING
3
Do not attempt to repair or adjust this equipment. Contact your dealer or Service center. High risk of electric shock!
Do not place anything containing liquid on top of the projector. High risk of Electric
Shock or damage to the projector.
This may cause a fire or could give an electric shock.
BLANK
SOURCE
VOL-
MENU
VOL+
ENTER
PUSH
ENTER
VOL+
VOL-
MENU
BLANK
SOURCE
PUSH
Don’t insert any object into the exhaust vent .
This may cause a fire or could give an electric shock.
Don’t place the projector in direct sunlight or near a heat source(radiator or heater).
This may cause a fire or could give an electric shock.
PUSH
PUSH
Don’t remove any covers (except lens cover). High risk of Electric Shock!
ENTER
VOL+
VOL-
MENU
BLANK
SOURCE
PUSH
WARNING
Use an air spray or soft cloth that is wet with a neutral detergent and water for removing dust or stains on the projection lens.
ENTER VOL+
VOL-
MENU
BLANK
SOURCE
PU
SH
Only use the correct type of batteries for the remote control. Dispose of used batteries carefully.
This may cause a fire or could give an electric shock.
VOL+ ENTER
VOL-
MENU
BLANK
SOURCE
PUSH
Don’t look directly onto the lens when the projector is in use. Eye damage may occur!
O
LA
O L-
M
O L+ TE
PUSH
Don’t use the projector in damp place such as a bathroom or any place where it is likely to get wet. Serious damage could occur or risk of Electric Shock!
O U
C
R
E
LA
N K
V O
L-
M E
U
N
L+
V O
E
TE
R
PUSH
Don’t use the projector if there is smoke or unusual smell from the projector.
Disconnect from the mains and contact the service center. Risk of fire!
O
U C
E
LA N
K
O L-
M
E
V O
E TE
R
PUSH
Don’t look at laser beam directly as it may cause eye damage.
4
5
Safety Instructions
NOTES
Only use the projector on a level and stable surface.
It may fall down or be upset.
C
U R
LA N
O
L+
TE
R
O L-
U
M
N
PUSH
Disconnect from the mains and remove all connections before moving.
Damage of cords may cause a fire or electric shock.
Don’t cover the project when in use.
It makes internal temperature increase and causes a fire.
VOL+
ENTER
VOL-
MENU
BLANK
SOURCE
PUSH
Ensure the projector is connected to the nearest mains socket to prevent the mains lead from being stretched.
Loose connection may cause fire.
PUSH
Never touch the power plug with wet hand.
It may cause electric shock.
Don’t use alcohol, benzene, or thinners to clean any plastic parts of the projector.
Never use industrial chemicals or detergents.
PU
SH
Ensure the power lead doesn’t trail across any hot objects like a heater.
It may make covering parts melted and cause a fire or electric shock.
BLANK
L+
SO URCE
VO L-
ENU
VO ENTER
When disconnecting from the mains don’t pull the mains lead as this may damage the lead internally.
If you hold the cord when unplugging, the internal line of the cord may be cut. This may cause heating and a fire.
NOTES
Don’t touch the lens of the projector. It may cause damage of it.
Don’t use any sharp tools on the projector as this will damage the casing.
ENTER
VOL+
VOL-
MENU
BLANK
SOURCE
PUSH
ENTER VOL+
VOL-
MENU
BLANK
SOURCE
PUSH
If the projector requires cleaning inside contact the service centre. Accumulated dust can cause mechanical failure.
Place the projector where people will not trip or tread on the power lead.
PUSH
LA
L+ TE
Use the indicated type of power source on the projector. If you are not sure of the type of power available, consult your dealer or customer service center.
Don’t place the projector or the remote control on a heater or use in a heated car.
PUSH
BLA
Don’t use the projector when the power cord or the plug is damaged or the connecting part of wall socket is loose.
It may cause electric shock or a fire.
PUSH
Be sure to unplug when you don’t use the projector for a long period or you are absent.
Accumulated dust may cause a fire, electric shock from deterioration, or electric leakage.
ENTER
BLANK
MENU
SOURCE
PUSH
6
Names of parts
7
Rear remote control sensor
Speaker Power button Control panel
Indicators
POWER
Handle
Horizontal leveler
BLANK
SOURCE
VOL+
ENTER
VOL-
MENU
Front remote control sensor
Zoom ring Foot Focus ring Lens cover
Foot adjusting button
Mouse
Computer Out
Computer
Audio
Computer In
R Audio L/MONO Video S-Video
AC
K
Computer Out
Computer Audio
Mouse
Computer In
S-Video
Audio / Video
Main power button
Kensington Security
System Connector
(Refer to page 12)
Rear remote control sensor
MENU Button
Selects or closes menus.
D
,
E
Button
Selects menus and items in the menus.
SOURCE Button
Switches to PC or
AV mode.
MENU ENTER
VOLVOL+
SOURCE BLANK
ENTER Button
Checks present mode and saves the change of functions.
VOLUME Button
Adjusts volume level and functions of menus.
BLANK Button
POWER Button
8
Names of parts
POWER Button
SOURCE Button
L MOUSE Button
(Zoom-out Button)
MOUSE DRAG Button
BLANK Button
RESIZE Button
VOLUME Button
AUTO TRACKING Button
MENU Button
R MOUSE Button
(Zoom-in Button)
POINTER Button
LASER Button
ENTER Button
STILL Button
MUTE Button
ZOOM Button
9
1 Slide the battery cover in the direction of the arrow to remove.
2 Insert the batteries with correct polarity.
3 Replace the battery compartment cover to the arrow direction.
POWER Button
SOURCE Button
MENU Button
L MOUSE Button
(Zoom-out Button)
R MOUSE Button
(Zoom-in Button)
Selects ON/OFF of power.
Switches to PC or AV mode.
Displays or hides the menu.
* Corresponds to the Left - Click of PC Mouse. This button registers a menu selection and selects other custom functions.
* Downsizes the screen on the zoom function.
* Corresponds to the Right - Click of PC Mouse. This button registers a menu selection and selects other custom functions.
* Enlarges the screen size on zoom function.
POINTER Button * After selecting menus, controls selecting and adjusting functions with the direction of up, down, left, right.
* Moves the screen with the direction of up, down, left, right on zoom function.
* Moves and releases the selected icon on PC screen.
MOUSE DRAG Button Uses to select and drag an icon in PC mode.
ENTER Button Checks the present mode and saves the change of functions.
ZOOM Button
RESIZE Button
Refer to page 36.
Refer to page 37.
AUTO TRACKING Button Refer to page 39~40.
BLANK Button Refer to page 31~32.
STILL Button
MUTE Button
Refer to page 27.
Cuts off audio.
VOLUME Button
LASER Button
Adjusts volume level.
Makes a bright red laser point on the screen for attention.
(Don’t look at laser beam directly as it causes eye damage.)
10
Installation and Connection
11
Remote Control
1.5V
1.5V
Batteries 2 (size AA) Power Cord Audio/Video Cable
Audio Cable Computer Cable Portable Bag
Mouse Connecting Cables
MAC Desktop Adaptor
PS/2 Mouse Cable
(IBM PC or Compatible)
MAC Serial Mouse Cable
Optional Extras
* Contact your dealer for buying these items.
* When applying a ceiling installer, use only the ceiling installer for LCD projector.
* Contact your dealer for replacing a new lamp.
Ceiling installer for LCD projector
Screen for projecting
S-Video Cable
Lamp
● The projector has Kensington Security System Connector on the back panel. Connect the Kensington
Security system cable as below.
● For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached to the Kensington Security System set.
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipments such as notebook PCs or LCD projectors.
● Kensington Security System is an optional item.
K
AC
12
Installation and Connection
* Lamp Indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status of the projector.
Lamp Indicator
Temperature indicator Operation indicator
13
MENU ENTE
VOLVOL+
Operation Indicator
Lamp Indicator
Temperature Indicator
Orange
Green
Off
Orange
Standby.
On operation.
Power off.
Projection lamp is reaching the end of its life and needs to be replaced with a new lamp.(over 1400 hours)
“Replace the Lamp”
Red
Projection lamp has reached the end of its life and cannot project images any longer.
Replace the lamp with a new one. (over 1500 hours)
Red(flashing)
The projector has trouble in the lamp or around it.
Contact the service center.
Green(flashing) The lamp cover is not closed.
Orange
Red
Red (flashing)
This projector is in high temperature. If you don’t turn off the projector, it’ll be turned off automatically.
“Temperature is Too High”
The projector is turned off as its high temperature.
Power is turned off as the trouble of internal cooling fan. Contact your service center.
“ ” is the warning message on screen.
POWER
BLANK
SOURCE
VOL+
ENTER
VOL-
MENU
1 . Place the projector on a sturdy and horizontal surface with the PC or AV source.
2 . Place the projector in the correct distance from the screen. The distance between the projector and the screen determines the actual size of the image.
Screen size
610x460cm(300inch)
410x300cm(200inch)
200x150cm(100inch)
160x120cm(70inch)
120x90cm(50inch)
81x61cm(40inch)
Horizontal distance from projector to screen
12.55m~16.35m
8.35m~10.87m
4.16m~5.42m
2.90m~3.78m
2.06m~2.69m
1.64m~2.15m
3 . Turn the projector so that the lens can be at a right angle to the screen. If the projector is not at a right angle, the screen image will be crooked. At this time perform keystone function.
(Refer to page 35.)
4 . Connect the cables of the projector to a wall power socket and other connected sources.
14
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output.
* You can use resize function for VGA, SVGA output.
* Refer to page 41 for the projector supported monitor display.
Mouse
Computer Out
Computer
Audio
Computer In
R Audio L/MONO Video S-Video
AC
K a b c d
< How to connect >
a.
Connect either end of the computer cable to Computer In of the projector.
b. Connect the monitor cable from the PC monitor to Computer Out of the projector if you want to see the projected image on PC monitor.
c. Connect the audio cable from the PC (LINE OUT sound port) to Computer Audio of the projector.
* If the PC has two audio out ports of SPEAKER OUT and LINE OUT, connect the LINE OUT port to get better sound quality.
d. Connect the PS/2 mouse(for IBM PC or compatible) cable(6 pin) to the Mouse of the projector.
15
Connecting to a Notebook PC
Mouse
Computer
Computer Out Audio Computer In
R Audio L/MONO Video S-Video
AC
K a b c
< How to connect >
a. Connect either end of the computer cable to Computer In of the projector.
b. Connect the audio cable from the PC to Computer Audio of the projector.
c. Connect the PS/2 mouse(for IBM PC or compatible) cable(6 pin) to the Mouse of the projector.
16
Connecting to a Macintosh Desktop PC
* You must use the Macintosh desktop adaptor to connect the projector to a Macintosh PC.
Mouse
Computer Out
Computer
Audio Computer In
R Audio L/MONO Video S-Video
K c b a d e f
< How to connect >
a. Connect either end of the computer cable to Computer In of the projector.
b. Connect the monitor cable from the Macintosh monitor to Computer Out of the projector if you want to see the projected image on Macintosh monitor.
c. Set the adjusting number and letter of the Macintosh desktop adaptor in accordance with the resolution you want to use and connect the adaptor to the Macintosh. (Refer to page 18 ~ 19) d. Connect the computer cable to the Macintosh desktop adaptor.
e.
Connect the audio cable from the PC to Computer Audio of the projector.
f. Connect the mouse cable(4 pin) from the Macintosh mouse port to the Mouse of the projector.
17
Adjusting letter
ON
1 2 3 4 5 6 7 8 9
Adjusting number
a.
How to use
Usually set 1 ~ 6 to OFF status and 7 ~ 9 to ON status of the adjusting numbers. And select the adjusting letter which is correct to the Macintosh and the monitor. (Refer to page 19.)
b. Notes for Connecting to the Macintosh PowerBook
If you get problems when connecting it to the projector, set the adjusting number 9 to OFF status and restart the Macintosh PowerBook.
18
Connecting to a Macintosh PC
19
LCII
LCIII
LC 475, LC 550
LC 575
Performa
400,405,410,430,600,600CD
450
Quadra
700,900
605,610,650,800,950
840AV
Centris
610,650
660AV
PowerBook
160,165C,180,180C
DUO DOC, MINI DOC
8 24 BOARD
M A C S output spec output resolution horizontal frequency(KHz) vertical frequency(Hz) adjusting letter
MAC llci, llsi
12 ¥ RGB
512x384
24.5
60
N
N
N MAC llvi, llvx
LC N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
J
J
J
J
13 ¥ x14 ¥
640x480
35
66
J
J
15 ¥ Portrait
640x870
68.8
75
O
O
VGA
640x480
31
60
G
J
J
G
M
O
O
O
G
G
G
G
SVGA
800x600
35
56
G
SVGA
800x600
56 or 72
G
16 ¥ Color
832x624
50
75
F
19 ¥ Color
1024x768
60
75
D
19 ¥ Color
1024x768
60 or 70
G
2Page Mono
1150x870
68.7
75
M
21 ¥ Color
1152x870
68.7
75
P
NTSC
NTSC
15.7
60
L
PAL
PAL
16
50
H
G
G
F
F
F D M P L H
J
J
J
J
J
J
J
J
J
J O
O
O
O
O
O
O
O
O
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
F
D
D
D
D G
G
M
M
M
M
M
M
P
P
P
P
P
P
L
L
L
H
H
H
L
L
H
H
L H
Connecting to a Macintosh PowerBook
b c d e
Mouse
Computer
Computer Out Audio Computer In
R Audio L/MONO Video S-Video
K a
< How to connect >
a.
Connect either end of the computer cable to Computer In of the projector.
b. Set the adjusting number and letter of the Macintosh desktop adaptor in accordance with the resolution you want to use and connect the adaptor to the Macintosh PowerBook.(Refer to page 18 ~ 19) c.
Connect the other end of the computer cable to the Macintosh desktop adaptor.
d.
Connect the audio cable from the PC to Computer Audio of the projector.
e.
Connect the mouse cable from the Macintosh mouse port to the Mouse of the projector.
20
Connecting to a Video Source
* You can connect a VTR, a camcorder, a LDP or any other compatible video image source to the projector.
Mouse
Computer Out
Computer
Audio Computer In
R Audio L/MONO Video S-Video
K a b
S VIDEO
OUT
(R) AUDIO (L) VIDEO
IN
< How to connect 1 >
a.
When connecting the projector to an A/V source, connect the A/V input ports of the projector to the output ports of the A/V source with A/V cables of the same color. The video cable is yellow and the left audio is white and right audio is red.
< How to connect 2 >
b.
Connect S-Video input port of the projector to S-Video output port of A/V source with S-Video cable.
* You can get better picture quality when connecting S-Video source to the projector.
* If you connect S-Video cable and Video cable simultaneously, you will get only the playing image of S-
Video source.
* If the Audio output of other external equipments is mono, do connect Audio cable only to the white port(Audio L) of the projector.
21
Turning on the Projector
1 Remove the lens cover of the projector.
2 Press the main power button on the back panel.
3 Press the POWER button on the remote control or top cover.(Green operation indicator flashes during warming up of the lamp.)
●
●
An image appears after the green power indicator is flashed for some time.
Select the source mode with the SOURCE button.
4 Adjust volume level.
●
●
If you press VOLUME G button, sound and volume level number are increased.
If you press VOLUME F button, sound and volume level number are decreased.
24
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* Don’t turn main power off and don’t unplug the power cord while the ventilation pan(inlet/outlet) is working.
22
Operating the Projector
When an image appears on the screen, check if it is in proper focus and fits well to the screen.
POWER
BLANK
SOURCE
VOL+
ENTER
VOL-
MENU
Zoom ring Focus ring
● To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
● To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens.
To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector by pushing foot adjuster button as below.
Push
1.
Press the foot adjuster button while you support the other side of the projector. This unlocks the foot and can make it move freely. Take care not to drop the projector.
2.
While pressing the foot adjuster button, raise or lower the projector to place the screen image in the proper position.
3.
Release the button to lock the foot in its new position.
4.
To fine-tune the height of the projector, rotate the front foot to raise or lower it.
After raising the front foot, do not press down on the projector.
23
If the projector is installed on a place that is not stable or horizontal, the projected screen shape will be distorted.
POWER
BLANK
SOURCE
VOL+
VOL-
ENTER
MENU
Horizontal leveler
● Adjust the screen shape to be horizontal and rectangular with horizontal leveler as above.
24
Function checking
* Without PC or Video signal the OSD doesn’t appear.
1 Press the MENU button.
2 Move the POINTER button up or down to select a menu and press the ENTER button. Each time you press the button you can see menus as below.
exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING exit move adjust
E
G
G
G
VIDEO
Contrast
Brightness
Color R
Color G
Color B
Reset
POSITION
SPECIAL
TRACKING exit move enter
G VIDEO
G POSITION
G SPECIAL
E TRACKING
Auto Tracking
Clock
Phase
Press Enter to Start exit move select
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
English G exit move adjust
G
E
VIDEO
POSITION
Horizontal
Vertical
Keystone
Zoom
Resize
G SPECIAL
G TRACKING
3 Move the POINTER button up or down to select a function that you want to use or adjust.
● To finish the menu display, press the MENU button repeatedly.
* In AV mode, [Horizontal] / [Vertical] in POSITION menu, [VGA Text] in SPECIAL menu and TRACKING menu are not displayed.
* The sub menus of VIDEO menu in AV mode are different from those in the PC mode. (Refer to page 38).
25
Selecting source mode
1 Press the SOURCE button
2 Each press of the SOURCE button changes the display as below.
PC AV
26
Using Still function
1 Press the STILL button.
* You can still the input image from PC or AV source.
<Moving Image>
2 To finish this function, press the STILL button again.
<Still Image>
27
Selecting language
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu as below.
exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select [Language] item.
3 Move the POINTER button left or right to select the language you want to use.
● On-Screen-Display(OSD) is marked in the selected language from this point.
● To finish menu display, press the MENU button repeatedly.
exit move select
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
English G
28
Using Flip Horizontal / Vertical function
* This function reverses the left and the right side of the projected image. Use this function when projecting from behind onto a transparent screen being viewed from the opposite side.
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu.
exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select [Flip Horizontal] item.
exit move enter
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
Press Enter to Flip
3 Press the ENTER button to see reversed image.
● Each time you press the button, the image will be reversed.
● To finish menu display, press the MENU button repeatedly.
exit move enter
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
Press Enter to Flip
Press Enter to Flip exit move enter
Flip Horizontal
Blank Image
Flip Vertical
VGA Text
Lamp Time
TRACKING
POSITION
Language
SPECIAL
VIDEO nu Menu Me
G
G
E
G
29
Flip V ertical Function
* This function reverses the upper and the lower side of the projected image.
* When you hang the projector upside down from the ceiling for using, you need to reverse all the sides(left, right, upper, lower) of the image.
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu. exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select [Flip Vertical] item.
exit move enter
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
Press Enter to Flip
3 Press the ENTER button to see reversed image.
● Each time you press the button, the image will be reversed.
● To finish menu display, press the MENU button repeatedly.
exit move enter
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
Press Enter to Flip
G TRACKING
VGA Text
Lamp Time
Blank Image
Flip Vertical
Flip Horizontal
Language
SPECIAL
E
G POSITION
G VIDEO
Press Enter to Flip exit move enter
30
Using Blank function
* This function may be effective if you need to get attention of the attendants in meetings or briefings.
1 Press the BLANK button.
* The screen turns to be covered with background color and sound becomes off.
* You can choose the background color. Refer to page 32.
2 To exit the blank status, press the BLANK button again.
* If exiting the blank status sound also becomes on.
31
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu. exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select the [Blank Image] item.
3 Move the POINTER button left or right to select the color you want to use.
● Background color will be changed to the selected color from this point.
● To exit menu display, press the MENU button repeatedly.
exit move select
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
Blue G
32
Checking lamp time
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu as below.
exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select the [Lamp Time] item.
exit move
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
0 Hr
● You can see the used lamp time.
● When the lamp time is reaching 1400 hours, the lamp indicator is turned to orange color.
33
Selecting PC screen size input signal
* When PC input mode, select the appropriate screen size in SPECIAL menu as below before turning on the
PC to get the image size of PC on DOS mode to be fit on the projected screen.
* In other screen size signals except 640X400 70Hz and 720X400 70Hz, the projected screen sizes are adjusted automatically.
1 Press the MENU button and move the POINTER button up or down to select the SPECIAL menu as below.
exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select the [VGA Text] item.
3 Move the POINTER button left or right to select the screen size you want to use.
exit move select
G VIDEO
G POSITION
E SPECIAL
Language
Flip Horizontal
Flip Vertical
Blank Image
Lamp Time
VGA Text
G TRACKING
720X400 G
● a. Selecting 720X400
: When input signals are 720X400 70Hz or 640X400 70Hz , the projected screen size is always adjusted to the format of 720X400 70Hz.
b. Selecting 640 X 400
: When input signals are 720X400 70Hz or 640X400 70Hz , the projected screen size is always adjusted to the format of 640X400 70Hz.
● To exit menu display, press the MENU button repeatedly.
34
Adjusting screen display
* If the image size does not fit the screen in accordance with the input source, set the position of the image by selecting Horizontal / Vertical position.
* Keystone function adjusts the upper and lower width of the projected image to prevent the image shape from being a trapezoid shape. Use this function when the screen or the projector is slanted and cannot make rectangular projection angle.
1 Press the MENU button and move the POINTER button up or down to select the POSITION menu. exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select (Horizontal),
(Vertical) or (Keystone) item.
< PC mode > exit move adjust
G VIDEO
E POSITION
Horizontal
Vertical
Keystone
Zoom
Resize
G SPECIAL
G TRACKING
3 Press the POINTER button and move the button left or right or press the VOLUME ( F
, to adjust the screen condition as you want.
G ) button
● (Horizontal), (Vertical) , (Keystone) are adjusted from -50 to +50.
● To exit the menu display, press the MENU button repeatedly.
35
1 Press the ZOOM button.
2 Move the POINTER button to move the rectangular zooming area and press the ENTER button to zoom the target area.
3 Press the L MOUSE or R MOUSE button to adjust the zoom level.
* L MOUSE button makes the image look smaller.
* R MOUSE button makes the image look larger.
11/25 25/25
4 Move to the position you want to see the enlarged display by moving the POINTER button left,right,up, or down.
5 Press the ZOOM button again to finish the zoom function.
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* You can use this function by using the MENU button.
* In the zoom mode, you can adjust horizontal / vertical position with the POINTER button.
36
Using Resize function
* You can use this function only under SVGA (800x600) mode in case of LP-XG2 model.
1 Press the RESIZE button.
Each press of the button changes the display as below.
< PC mode > < AV mode >
4 : 3 Scaled
Original 16 : 9
37
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* You can also use this function by using the MENU button.
Adjusting Video
1 Press the MENU button and move the POINTER button up or down to select each VIDEO menu.
<PC Mode>
<AV Mode> exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING exit move enter
G VIDEO
G POSITION
G SPECIAL
2 Press the ENTER button.
<PC Mode> exit move adjust
E VIDEO
Contrast
Brightness
Color R
Color G
Color B
Reset
G POSITION
G SPECIAL
G TRACKING
<AV Mode> exit move adjust
E VIDEO
Contrast
Brightness
Color
Tint
Reset
G POSITION
G SPECIAL
3 Move the POINTER button up or down to select a video item you want to adjust.
4
Move the POINTER button left or right or press the VOLUME ( F
,
G ) button to adjust the selected video item as you want.
● To restore the original image condition after changing it, press ENTER button after selecting (Reset) item.
● To finish menu display, press the MENU button repeatedly.
38
Using Tracking function
● TRACKING menu is not displayed in <AV mode>.
Auto T racking Function
* Auto Tracking Function
This function assures you of getting the best video quality by automatically adjusting the difference of horizontal width and tremor of the image. This difference is caused by disaccord of the internal signal of the projector and diverse graphic signals of PC.
* This function is operated only in PC mode.
1 Press the AUTO TRACKING button.
Auto Tracking
* Image positioning and tremor adjusting are automatically performed.
2 Adjust [Clock] or [Phase] in TRACKING menu after operation of [Auto Tracking] if you want to get better picture quality in accordance with diverse PC input modes. (Refer to page 40.)
39
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* You can also use this function by using the MENU button.
* Perform this function while on stopped image because you may not get the best video quality on a moving image of PC graphic signal.
* TRACKING menu is not displayed in AV mode.
* Clock Function
This function adjusts the horizontal width of the projected image to get the image to fit on the screen size.
* Phase Function
This function is for the detailed adjustment of the clock function.
* These functions are operated only in PC mode.
1 Press the MENU button and move the POINTER button up or down to select the TRACKING menu. exit move enter
G VIDEO
G POSITION
G SPECIAL
G TRACKING
2 Press the ENTER button and move the POINTER button up or down to select the (Clock) or
(Phase) item.
exit move adjust
G VIDEO
G POSITION
G SPECIAL
E TRACKING
Auto Tracking
Clock
Phase
3
Move the POINTER button left or right or press the VOLUME ( F
, condition.
G ) button to adjust the screen
● To exit the menu display, press the MENU button repeatedly.
40
Supported Monitor Display
* The projector displays images at a resolution of 1024x768 pixels. To display higher resolution images(1152x864mode, 1280x1024mode), the projector compresses it to 1024x768. The following table lists the display formats supported by the projector.
Sources
VGAEGA
PC98 / VGA text
VGA
SVGA
XGA
SXGA
UXGA
MAC 16 ¥
19 ¥
20 ¥
Format
640X350
640X350
640X400
720X400
720X400
640X480
640X480
640X480
640X480
640X480
640X480
640X480
800X600
800X600
800X600
800X600
800X600
800X600
800X600
1024X768
1024X768
1024X768
1024X768
1024X768
1152X864
1152X864
1152X864
1152X864
1280X960
1280X960
1280X960
1280X1024
1280X1024
1280X1024
1600X1200
832X624
1024X768
1024X768
1152X870
Vertical Freq.(Hz)
70.090Hz
85.080Hz
85.080Hz
70.082Hz
85.039Hz
59.940Hz
66.667Hz
72.800Hz
75.00Hz
85.008Hz
100.040Hz
120.00Hz
56.250Hz
60.317Hz
72.188Hz
75.00Hz
85.061Hz
90.00Hz
100.00Hz
43.479Hz
60.004Hz
70.069Hz
75.029Hz
84.997Hz
60.053Hz
70.016Hz
75.00Hz
85.057Hz
60.00Hz
75.00Hz
85.002Hz
60.020Hz
75.025Hz
85.024Hz
60.00Hz
74.550Hz
60.004Hz
75.029Hz
75.062Hz
Horizontal Freq. (kHz)
31.468kHz
37.861kHz
37.861kHz
31.469kHz
37.927kHz
31.469kHz
35.00kHz
37.861kHz
37.500kHz
43.269kHz
53.011kHz
64.062kHz
35.156kHz
37.879kHz
48.077kHz
46.875kHz
53.674kHz
56.00kHz
64.016kHz
35.522kHz
48.363kHz
56.476kHz
60.023kHz
68.677kHz
54.348kHz
63.995kHz
67.500kHz
77.487kHz
60.00kHz
75.00kHz
85.938kHz
63.981kHz
79.976kHz
91.146kHz
75.00kHz
49.725kHz
48.363kHz
60.023kHz
68.681kHz
* If the projector does not support the input signal, “CHECK INPUT SIGNAL” message appears on the screen.
* The projector supports DDC1/2B type as Plug & Play function.(Auto recognition of PC monitor)
41
Maintenance
* The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear on the screen. You will also need to clean the air filter attached at the bottom of the projector periodically because a clogged air filter prevents proper ventilation that is necessary to cool the projector and prevents it from overheating. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector, always turn the power off and unplug the projector first.
Clean the lens whenever you notice dirt or dust on the surface of it. Wipe the lens surface gently with an air spray or a soft, dry lint-free cloth.
To remove dirt or stains on the lens, moisten a soft cloth with water and a neutral detergent and wipe the lens surface gently.
To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped.
Cleaning the Air Filter
The air filter, which is located at the bottom of the projector, should be cleaned after every 100 hours’ use.
If it is not cleaned periodically, it can become clogged with dust and prevent the projector from being ventilated properly. This may cause overheating and damage of the projector.
To clean the air filter :
1. Switch the projector off and unplug the power cable from the wall socket.
2. Stand the side of the projector so that the handle can be at the top, and you can easily access the air filter.
3. Push the opening tip of the air filter cover and remove the cover.
4. The air filter is in the cover of it. To clean the filter, you’d better use a small vacuum cleaner designed for computers or other office equipments. If not, you may use a dry, lint-free cloth.
If it is difficult to remove dirt or the filter is torn, contact your dealer or the service center to replace it .
5. Close the filter cover after cleaning.
6. Plug the power cable back into the wall socket.
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* When installing the projector on the ceiling use screws of which length is within 5 mm.
* Contact your dealer to get screwes for fixing, the ceiling installer and the detailed explanation to install.
42
Maintenance
Reset Lamp T ime
* You must reset lamp time on the menu after replacing the lamp.
1 Turn the power off but keep pluged in. Press the buttons on the control panel in the sequence as below.
D E F
Lamp time will be initialized.
G MENU ENTER
43
POWER
BLANK
SOURCE
VOL+
ENTER
MENU
* Power is not turned on after 1500 hours’use. In this case, you can turn the power on only by initiating the lamp time with the above operation.
* If you don’t replace the lamp after resetting the lamp time, the lamp may be damaged.
LP-XG2
22.9mm(0.9 inches)
LP-XG2 : 1024(Horizontal) x 768(Vertical)pixel
1.01~7.6m(40~300 inches)
1.64~16.35m(5.03~54.08 feet)
12m
1W
4:3(horizontal:vertical)
1:1.3
AC 110 - 240V~50/60Hz
98.5mm(including front foot)
238mm
329.5mm(including lens)
3.4kg
Specifications.
Model
LCD panel size resolution screen size projecting distance remote control distance speaker system horizontal / vertical ratio zoom ratio
Power height breadth length weight
Operating Condition temperature
In operation : 32~104°F(0°C~35°C)
In storage and transit : -4~140°F(-20°C~60°C)
humidity
In operation : 20 ~ 80% relative humidity by dry hygrometer
Not in operation : 10 ~ 90% relative humidity by dry hygrometer
Projection Lamp lamp model
TP-L2
power consumption
150W
44

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 1024x768 resolution
- Zoom function
- Resize function
- Auto tracking function
- Flip Horizontal / Vertical function