LG | LRSC21935TT | User's Manual | LG LRSC21935TT User's Manual

LRSC21935TT
LRSC21935SW
LRSC21935SB
Table of contents
Introduction
Installation
Operation
Suggestion on
food storage
Care and
maintenance
2
Entry
3
Important safety instruction
3
Identification of parts
4
Where to install
5
Door removal
6
Door replacement
7
Feed water pipe installation
7
Water connection instruction guide
8
Operation instruction guide
10
Height adjustment
12
Starting
13
Adjusting the temperatures and functions
(Dispenser / Automatic ice maker)
13
Shelf (Applicable to some models only)
18
Wine holder (Applicable to some models only)
18
Egg box
19
Humidity control in the vegetable compartment
19
Convert into a vegetable or meat compartment
19
Deodorizer (Applicable to some models only)
20
Location of foods
21
Storing foods
22
How to dismantle parts
23
General information
25
Cleaning
25
Trouble shooting
26
Introduction
Entry
The model and serial numbers are found on the inner case or back of refrigerator
compartment of this unit. These numbers are unique to this unit and not
available to others. You should record requested information here and retain
this guide as a permanent record of your purchase. Staple your receipt here.
Date of purchase
Dealer purchased from
Dealer address
Dealer phone no.
Model no.
Serial no.
:
:
:
:
:
:
Important safety instruction
Before it is used, this refrigerator must be properly installed and located in accordance with
the installation instructions in this document.
Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull
it straight out from the outlet.
When moving your appliance away from the wall, be careful not to roll over the power cord
or to damage it in any way.
After your refrigerator is in operation, do not touch the cold surfaces in the freezer
compartment, particularly when your hands are damp or wet. Skin could adhere to these
extremely cold surfaces.
Unplug the power cord from the power outlet for cleaning or other requirements. Never
touch it with wet hands because you can get an electric shock or be hurt.
Never damage, process, severely bend, pull out, or twist the power cord because damage
the power cord may cause a fire or electric shock. You have doubts on whether the
appliance is properly grounded.
Never place glass products in the freezer because they may be broken due to expansion
when their contents are frozen.
Never allow your hands within the ice storage bin of the automatic ice maker. You could be
hurt by the operation of the automatic ice maker.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young childeren should be supervised to ensure that they do not play with the appliance.
Never allow anyone to climb, sit, stand or hang on the refreshment center door. These
actions may damage the refrigerator and even tip it over, causing severe personal injury.
Before you move your refrigerator into its final location,
it is important to make sure you have the proper electrical
connection:
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet that
cannot be turned off by a switch. Do not use an extension cord.
The refrigerator-freezer should be so positioned that the supply plug
is accessible for quick disconnection when accident happens.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid a hazard.
Do not modify or extend the Power Cord length.
It will cause electric shock or fire.
Recommended
Grounding
Method
Accessibility of
Supply Plug
Supply Cord
Replacement
Warning
3
Introduction
Child entrapment
warning
DANGER: Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors but leave the shelves in place so that children may not easily climb
inside.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the appliance.
Don’t store
Don’t store or use gasoline or other flammable vapor and liquids in the vicinity of this or
any other appliance.
Grounding (Earthing)
In the event of an electric short circuit, grounding (earthing) reduces the risk of electric
shock by providing an escape wire for the electric current.
In order to prevent possible electric shock, this appliance must be grounded
improper use of the grounding plug can result in an electric shock. Consult a qualified
electrician or service person if the grounding instructions are not completely
understood, or if you have doubts on whether the appliance is properly grounded.
Identification of parts
Freezer
compartment
Refrigerator
compartment
Milk product corner
Lamp
Door rack
Shelf
Door rack
Automatic
ice maker
Wine holder (Optional)
Lamp
Shelf
Snack drawer (Optional)
Shelf
(steel or glass)
Egg box
Lamp
Door rack
(Optional)
Vegetable drawer(1 or 2)
Door rack
Shelf
Vegetable
drawer/Meat drawer
Drawer (1 or 2)
Door rack
(Optional)
Humidity switch
Lower cover
Conversion switch
(Meats/Vegetables)
NOTE
•
4
If you found some parts missing from your unit, they may be parts only used in other
models. (i.c. the “Refreshment center” is not included in all models)
Installation
Where to install
1. Place your appliance where it is easy to use.
Select a good
location
2. Avoid placing the unit near heat sources, direct sunlight or moisture.
3. To avoid vibrations, the appliance must be leveled.
4. Don't install the appliance below 5∞C. It may cause affect the performance.
5
Installation
Door removal
Warning
Electric Shock Hazard
Disconnect electrical supply to refrigerator before installing.
Failure to do so could result in death or serious injury.
If your access door is too narrow for the
refrigerator to pass through, remove the
refrigerator door and pass the refrigerator laterally.
Remove lower
cover and
then feed water
tube
Lower cover
Remove the lower cover by lifting upward, and
then pull up the feed water tube while pressing
area shown in the figure to the right.
Feed water tube
NOTE
•
Remove the
freezer
compartment
door
If a tube end is deformed or abraded, cut the part away.
Hinge
cover
1) Removing the hinge cover by loosening the
screws. Separate all connection wires except
for the earth line after.
Upper hinge
Connection
wires
Earth line
Keeper
2) Remove the keeper by rotating it counter
clockwise () and then lifting the upper
hinge up ().
Upper hinge
NOTE
•
When removing the upper hinge, be careful that the door does not fall forwards .
3) Remove the freezer compartment door by
lifting it upward. This time, the door should
be lifted enough for the feed water pipe tube
to be completely pulled out.
Lower hinge
NOTE
•
Remove the
refrigerator
door
Move the refrigerator compartment door passing through the access door and lay
it down, but be careful not to damage the feed water pipe tube.
1) Loosen the hinge cover screws and remove
the cover. Remove connection wire, if any,
except for the earth line.
Connection
wires
2) Remove keeper by rotating it clockwise ()
and then remove the upper hinge by lifting
it up ( ).
Upper hinge
3) Remove the refrigerator compartment door
by lifting it up.
6
Lower hinge
Keeper
Installation
Pass the refrigerator laterally through the access
door as shown in the right figure.
Pass the
refrigerator
Max
5
4
3
2
1
FRZ
TEMP
Min
1
2
REF
TEMP
3
4
5
Max
Door replacement
Mount them in the reverse sequence of removal after they pass through the access
door.
Feed water pipe installation
Before
installation
Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5
kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.).
2
If water pressure does not reach the rating 147 kPa (1.5 kgf/cm ) or below, it is
necessary to purchase a separate pressure pump for normal automatic icing and
cool water feed.
Keep the total length of the feed water pipe tube within 8 m and be careful for the
tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed
owing to the drain water pressure.
Install the feed water pipe tube at a place free from heat.
Warning
7
Connect to potable water supply only.
Refer to instructions with water filter kit for installation.
Installation
Water connection instruction guide
Connecting
the refrigerator
to a water source
Read all directions carefully before you begin.
Warning
Connect to potable water supply only.
IMPORTANT
Tools required
•
If operating the refrigerator before installing the water connection, turn ice maker
to the OFF position to prevent operation without water.
•
All installations must be in accordance with local plumbing code requirements.
•
Use copper tubing and check for leaks.
•
Install copper tubing only in areas where temperatures will remain above freezing.
•
It may take up to 24 hours for your ice maker to begin producing ice.
Standard screwdriver
7/16 - inch and 1/2 - inch open-end wrenches or two adjustable wrenches
1/4 - inch nut driver
1/4 - inch drill bit
Hand drill or electric drill (properly grounded)
NOTE
•
Cold water supply
Your refrigerator dealer has a kit available with a 1/4 - inch saddle-type shut - off valve,
a union, and copper tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing-type or 3/16 - inch
saddle valve which reduces water flow and clogs more easily.
The ice maker water valve contains a flow washer which is used as a water
pressure regulator.
The ice maker needs to be connected to a cold water line with water pressure
207 ~ 827 kPa (30 ~ 120 psi).
If a problem occurs, call your utility company.
8
Installation
Connect
the tubing to
water line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long enough to empty
water pipes.
3. Find a 1/2 - inch to 1-1/4 - inch vertical COLD water pipe near the refrigerator.
NOTE
•
Horizontal pipe will work, but the following precaution must be taken: Drill on the top
side of the pipe, not the bottom. This will help keep water away from the drill. This also
keeps normal sediment from collecting in the valve.
4. To determine the length of copper tubing you will need, measure from the
connection on the lower left rear of the refrigerator to the water pipe. Add 7
feet (2.1m)to allow for moving refrigerator for cleaning. Use 1/4 -inch O.D.
(outside diameter) copper tubing. Be sure both ends of copper tubing are cut
square.
5. Using a grounded drill, drill a 1/4 - inch hole in the cold water pipe you have
selected.
6. Fasten shut - off valve to cold water pipe with pipe clamp. Be sure outlet end
is solidly in the 1/4-inch drilled hole in the water pipe and that the washer is
under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do not over tighten or
you may crush the copper tubing, especially if soft (coiled) copper tubing is
used. Now you are ready to connect the copper tubing.
7. Slip compression sleeve and compression nut on copper tubing as shown.
Insert end of tubing into outlet end squarely as far as it will go. Screw
compression nut onto outlet end with adjustable wrench. Do not over tighten.
8. Place the free end of the tubing into a container or sink, and turn ON main
water supply and flush out tubing until water is clear. Turn OFF shut - off valve
on the water pipe. Coil copper tubing.
Cold Water Pipe
Pipe Clamp
Packing Nut
Coil of polyethylene or
Copper Tubing
Shut Off Valve
Compression Sleeve
9
Compression Nut
Installation
Operation instruction guide
Connect the tubing to
the refrigerator
Before making the connection to the
refrigerator, be sure the refrigerator
power cord is not plugged into the wall
outlet.
1. Remove the plastic flexible cap from
the water valve.
2. Place the compression nut and ferrule
(sleeve) onto the end of the tubing as
shown.
3. Insert the end of the copper tubing into
the water valve connection as far as
possible. While holding the tubing,
tighten the fitting.
Turn the water on at
the shutoff valve
Copper tubing
(Provided)
Compression nut
(Provided)
Ferrule (sleeve)
Water valve
Tighten any connections that leak.
Automatic ice maker
Plug In the Refrigerator
Arrange the coil of copper tubing so that it does not vibrate against the back of
the refrigerator or against the wall. Push the refrigerator back to the wall.
Start the lcemaker
Set the ice making stop switch to the ON position The icemaker will not begin
to operate until it reaches its operating temperature of 15 °F (-9 °C) or below. It
will then begin operation automatically if the ice making stop switch is in the
ON position.
The automatic ice maker can automatically make 8 pieces of ice cube at a time,
80-100 pieces a day.
But these quantities may be varied according to various conditions including
how many times the refrigerator door opens and closes.
Ice making stops when the ice storage bin is full.
NOTE
•
10
It is nomal that a noise is produced when ice made is dropped into the ice storage bin.
Installation
When ice maker
does not operate
smoothly
Ice is clumped together
When ice is clumped together, take the ice clumps out of the ice storage bin,
break them into small pieces, and then place them into the ice storage bin
again.
When the ice maker produces too small or clumped ice, the amount of water
supplied to the ice maker need to adjusted. Contact the service center.
If ice is not used frequently, it may clump together.
Power failure
Water may drop into the freezer compartment. Take the ice storage bin out and
discard all the ice then dry it and place it back.
The unit is newly installed
It takes about 12 hours for a newly installed refrigerator to make ice in the
freezer compartment.
Throw away the ice (about 20 pieces) first made after refrigerator installation.
CAUTION
The first ice and water may include particles or odor from the feed water pipe or
feed water box.
This is also necessary if the refrigerator has not been used for a long time.
Never store beverage cans or other foods in ice storage bin for the purpose of rapid
cooling.
Such actions may damage the automatic ice maker.
Never remove the ice maker cover.
Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice may pile up just around the ice maker causing the ice maker to think that the ice
storage bin is ful.
If discolored ice is dispensed, immediately contact Service Center.
Do not use until problem is solved.
11
Installation
Height adjustment
If the freezer
compartment door
is lower than the
refrigerator
compartment door
Level the door by inserting flat ( - type) driver into the groove of the left height adjusting
screw and rotate it clockwise ().
If the freezer
compartment door
is higher than the
refrigerator
compartment door
Level the door by inserting flat ( - type) driver into the groove of the right height
adjusting screw and rotate it clockwise ().
After leveling the
door height
The refrigerator doors will close smoothly by heightening the front side by adjusting
the height adjusting screw. If the doors do not close correctly, performance may be
affected.
Next
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their
proper places. They are packed together to prevent possible damage during shipping.
3. Connect the power supply cord (or plug) to the outlet. Don't double up with other
appliances on the same outlet.
12
Operation
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating
temperatures for 2-3 hours prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
Adjusting the temperatures and functions
CUBE
ON
DIGITAL CONTROL
FITER STATUS
WATER
OFF
CRUSH
EXPRESS FRZ
DISPENSER
LOCK
3 SECS
REF TEMP
FRZ TEMP
FREEZER
FILTER RESET
HOLD 3 SECS
REFRIGERATOR FILTER RESET
UNLOCK
LOCK
Lock button.
Super freezer.
Dispenser
Filter reset button.
selection button.
Temperature adjustment button
for freezer compartment.
13
Temperature adjustment button
for refrigerator compartment.
Operation
You can adjust temperature of and freezer room and refrigerator room.
How to adjust the
temperature in
the freezer
compartment
Freezer room temperature adjustment
FREEZER
Setting
temperature
Refrigerator room temperature adjustment
How to adjust the
temperature in
the refrigerator
compartment
REFRIGERATOR
Setting
temperature
❇ Whenever pressing button, setting is repeated in the order of (Middle) ➔
(Middle Strong) ➔ (Strong) ➔ (Weak) ➔ (Middle Weak).
The actual inner temperature varies depending on the food status, as the
indicated setting temperature is a target temperature, not actual temperature
within refrigerator.
Refrigeration function is weak in the initial time. Please adjust temperature as
above after using refrigerator for minimum 2~3 days.
Dispenser use
selection
You can select water or ice.
❇ Please select water, slice ice and square ice by
pressing
button as you desire.
❇ Please press the push button lightly by catching and
pushing in cup.
The border line is indicated for the selected function,
"Tak!" sounds if 5 seconds pass after ice comes out.
It is sound that the outlet of ice is closed.
DISPENSER
•
14
Reference : Please wait for 2-3 seconds in order to take final ice
slices or drops of water when taking out cup from the
pressing switches after taking ice or water.
DISPENSER
CUBE
WATER
CRUSH
Pressing
Switch
Operation
The icemaker can automatically make 8 pieces of ice cubes at anyone time,
approximately 80 pieces per day. However these quantities may vary according to
certain conditions. E.g. the duration and amount of times the refrigerator door is
opened.
The Ice making proceeds ceases automatically when the ice storage bin is full.
If you choose not to use the automatic ice making function, repositioned the
icemaker selection switch to the off position or the on position for reselection. Note:
The manual selection function is only applicable to some models only.
Automatic ice
maker
NOTE
•
It is normal that a noise is produced when ice made is dropped into the ice storage
bin.
Ice is lumped together
When ice is lumped together, take the ice lumps out of the ice storage bin, break
them into small pieces, and then place them into the ice storage bin again.
When the ice maker produces too small or lumped together ice, the amount of
water supplied to the ice maker need to adjusted. Contact the service center.
❈ If ice is not used frequently, it may lump together.
When ice maker
does not operate
smoothly
Power failure
Ice may drop into the freezer compartment. Take the ice storage bin out and discard
all the ice then dry it and place it back. After the machine is powered again, crushed
ice will be automatically selected.
The unit is newly installed
It takes about 12 hours for a newly installed refrigerator to make ice in the freezer
compartment.
Please select this function for prompt freezer.
"On" or "Off" is repeated whenever pressing
button.
EXPRESS FRZ
The arrow mark graphic remains at the On
status when selecting Special Refrigeration "On".
Super freezer function automatically turns off if a
fixed time passes.
Super freezer
EXPRESS FRZ
This button stops operation of different
button.
LOCK
Locking or Release is repeated whenever
pressing the
.
Pressing the other button when selecting ‘LOCK’,
the button does not operate.
Lock
LOCK
15
ON
ON
OFF
OFF
Ex) In selecting
Ex) In selecting
"On"
"Off"
LOCK
LOCK
3 SECS
3 SECS
UNLOCK
UNLOCK
Ex) In selecting
Ex) In selecting
"LOCK"
"UNLOCK"
Operation
The other
functions
Door open warning
3 times of warning sounds at the interval of 30 seconds if a minute passes with the
door of refrigerator and the hombar door opened or completely closed.
Please contact with the local service center if warning continue to sound even after
closing the door.
Diagnosis (failure detection) function
Diagnosis function automatically detects failure when failure is found in product during
the use of refrigerator.
If failure occurs at product, it does not operate though pressing any button and normal
indication is not done. In this case, do not turn power off but immediately contact with
the local service center. A lot of time are need for service engineer to detect the failed
part if turning it off.
Water is cooled while stored in the water tank in the refrigerator compartment, and
then sent to the dispenser.
Ice is made in the automatic ice maker and sent to the dispenser divided into crushed
or cubed form ice.
How ice/cold
water is supplied
NOTE
•
How to use
dispenser
It is normal that the water is not very cold at first. If you want colder water, add
ice into the glass.
Select one among crushed ice, water, and cubed ice and slightly press the push
switch with a glass or other container.
Water
Light the water
indicating lamp by
pressing the selection
button.
• Water will be dispensed
by pressing the push
switch with a glass.
DISPENSER
16
WATER
Crushed ice
Light the crushed ice
indicating lamp by
pressing the selection
button.
• Crushed ice will be
dispensed by pressing the
push switch with a glass.
DISPENSER
CRUSH
Cubed ice
Light the cubed ice
indicating lamp by
pressing the
selection button.
• Cubed ice will be dispensed
by pressing the push
switch with a glass.
DISPENSER
CUBE
Operation
6 Filter condition
(filter replacement
cycle) display
function
After 6 months, the following sentence and
will appear on the filter condition
part of the LED. "Press for 3 seconds after replacing filter"
After 6 months have passed, and if the filter has been replaced or you want to reset
the filter condition display, press the filter replacement button for more than 3
seconds and it will reset to the initial Power On state.
Throw away the ice (about 20 pieces) and water (about 7 glasses) first made
after refrigerator installation.
The first ice and water may include particles or odor from the feed water pipe or feed
water box. This is necessary in case that the refrigerator has not been used for a long
time.
Cautions
Keep children away from the dispenser.
Children may push switch incorrectly bad or damage lamps.
Be careful that food is not block the ice
passage.
If foods are placed at the entrance of ice
passage, ice may not be dispensed. The ice
passage may also be covered with ice
powder if splinter ice is used only. This time,
remove the ice powder accumulated.
Never store beverage cans or other
foods in ice storage bin for the purpose
of rapid cooling.
Such actions may damage the automatic ice maker.
Never use thin crystal glass or crockery to collect ice.
Such glasses or containers may be broken.
Put ice first into a glass before filling water or other beverages.
Water may be splashed if ice is added to existing liquid in a glass.
Never touch a hand or other tools on ice outlet.
Touch may cause a part breakage or hand injury.
Never remove the ice maker cover.
Sometimes level the surface so that the ice storage bin is fully filled with ice.
Ice is piled up just near the ice maker. So, such status may be considered, by the ice
maker, that the ice storage bin is fully filled and ice making operation may stop.
If discolored ice is dispensed, immediately contact service center, stopping use.
Never use too narrow or deep glass.
Ice may be jammed in ice passage and, thus, the refrigerator may be failed.
Keep the glass at a proper distance from ice outlet.
A glass too close to the outlet may hinder ice from coming out.
17
Operation
Shelf (Applicable to some models only)
You can store taller items such as a gallon container or bottles by simply pushing
in front half of shelf underneath back half of shelf. Pull toward you to return to a
full shelf.
Silde-Under
Shelf
Wine holder
(Applicable to some models only)
Wine holder
adjustment
Bottles can be stored laterally with this wine corner. This can be attached to any
shelf.
In case of inserting the wine holder :
Pull the wine holder downward as in
after inserting it into the side anchoring
part of the shelf as in by catching it
upward as in .
2
1
In case of separating the wine holder :
Pull the wine holder inward as in ➃ after
holding it upward as in ➂ by catching it.
3
4
18
Operation
Egg box
You can move the egg box to a place you want and select another form of box
according to the amount of eggs.
[Normal]
[For Many Eggs]
NOTE
•
•
Never use the egg box as an ice storage bin. It can be broken.
Never store the egg box in the freezer compartment or fresh compartment.
Humidity control in the vegetable compartment
The humidity can be controlled by adjusting the humidity control switch to the
left/right when storing vegetabes or fruits.
High humidity
Close
Open
Low humidity
Close
Open
Convert into a vegetable or meat compartment
The bottom drawer in the refrigerator can be converted into a vegetable or meat
compartment
The meat compartment maintains the temperature at a lower point than the
refrigerator compartment so that meat or fish can be stored fresh longer.
NOTE
•
19
Vegetables or fruits are frozen if the conversion switch is set to meats
compartment. So, be sure to check it before storing foods.
Operation
Deodorizer (Applicable to some models only)
This system efficiently absorbs strong odors
by using the optical catalyst. This system
does hot have any affect on stored food.
How to use the
deodorizing
system
Since it is installed already installed onto the cool air intake duct from the from
the refrigerator compartment, you need no separate installation.
Please use closed containers to store food with pungent odors.
Otherwise, this oder can be absorbed by other food in the compartment.
20
Suggestion on food storage
Location of foods
(Refer to identification of parts)
Wine holder
Store wine.
Snack drawer
Store small foods such as bread, snacks, etc..
Freezer
compartment
shelf
Store various frozen foods such as meat, fish,
ice cream, frozen snacks, etc..
Freezer
compartment
door rack
Freezer
compartment
drawer
Store small packed frozen food.
Temperature is likely to increase as door
opens. So, do not store long-term food such
ice cream, etc..
Store meat, fish, chicken, etc.. after
wrapping them with thin foil.
Store dry.
Store milk products such as butter, cheese,
etc..
Milk product
corner
Egg box
Place this egg box in the proper location.
Refreshment
center
Store foods of frequent use such as beverage,
etc..
Refrigerator
compartment
shelf
Store side dishes or other foods at a proper
distance.
Refrigerator
compartment
door rack
Store small packed food or beverages such
as milk, juice, beer, etc..
Vegetable drawer
Store vegetables or fruits.
Vegetable
drawer
/meat drawer
conversion corner
Store vegetable, fruits, meat to thaw, raw
fish, etc.. setting the conversion switch as
necessary.
Be sure to check the conversion switch
setting before storing foods.
21
Suggestion on food storage
Storing foods
Store fresh food in the refrigerator compartment. How food is frozen and thawed is an
important factor in maintaining its freshness and flavor.
Do not store food which goes bad easily at low temperatures, such as bananas, and
melons.
Allow hot food to cool prior to storing, placing hot food in the refrigerator could spoil
other food, and lead to higher energy consumption.
When storing the food, cover it with vinyl wrap or store in a container with a lid. This
prevents moisture from evaporating, and helps food to keep its taste and nutrients.
Do not block air vents with food. Smooth circulation of chilled air keeps refrigerator
temperatures even.
Do not open the door frequently. Opening the door lets warm air enter the refrigerator,
and cause temperatures to rise.
Never keep too much food in door rack because they may push against by inner racks
so that the door cannot be fully closed.
Freezer
compartment
Refrigerator
compartment
Do not store bottles in the freezer compartment - they may break when frozen.
Do not refreeze food that has been thawed. This causes loss of taste and nutrient.
When storing frozen food like ice cream for a long period, place it on the freezer
shelf, not in the door rack.
Do not touch the cold foods or containers- especially made of metallic -, with wet
hands and place glass products in the freezer compartment.
- That’s why you may have chilblains and they may be broken when their inner matters
are frozen, causing personal injury.
Avoid placing moist food in top refrigerator shelves, it could freeze from direct
contact with chilled air.
Always clean food prior to refrigeration. Vegetables and fruits should be washed and
wiped, and packed food should be wiped, to prevent adjacent food from spoiling.
When storing eggs in their storage rack or box, ensure that they are fresh, and always
store them in an upright position, which keeps them fresh longer.
NOTE
•
22
If you keep the refrigerator in a hot and humid place, frequent openning of the door
or storing a lot of vegetables in it may cause dew to form which has no effect on its
performance. Remove the dew with dust cloth free from care.
Care and maintenance
How to dismantle parts
NOTE
•
Dismantling is done in the reverse sequence of assembly.
Be sure to unplug the power plug before dismantling and assembly.
Never apply severe force to dismantle parts. Parts may be damaged.
1
Freezer
compartment
lamp
Separate the lamp by pulling it out (➂) while
slightly striking (➀) and rotating (➁) the lamp
cover.
Turn the bulb counterclockwise. Max. 40 W bulb
for refrigerator is used and can be purchased at
a service center.
Dispenser lamp
Seperate the lamp by pulling it out, and then
remove the lamp. Max. 15 W bulb for
refrigerator is used and can be purchased at a
service center.
Freezer
compartment
shelf
To remove a shelf, lift the left part of the shelf
a bit, push it to the direction (), lift the right
part to the diretion (), and take it out.
Door rack and
support
Lift the door rack holding both sides () and
pull it out to () direction.
Ice storage bin
Hold the ice storage bin as shown in the right
figure and pull it out () while slightly lifting it
().
It is recommended not to dismantle the ice
storage bin unless it is necessary.
Be sure to use both hands when removing
the ice storage bin, so as not to drop it on the
floor.
If the ice storage bin does not fit well, slightly
rotate the rotating device.
2
3
EXPRESS/JET FRZ DISPENSER
FREEZER
REFRIGERATER FILTER/LIGHT
LOCK
1
After dispenser
is used
The water collector has no self-drainage
function. So it should be cleaned regularly.
Remove the cover by pressing the left side of
water collector cover and dry it with a cloth.
Press the point marked as shown in the figure
to the right to remove the water collector
cover.
23
2
2
1
Care and maintenance
Lamp in
refrigerator
compartment
To remove the lamp cover, press the protrusion under the lamp cover to the front and
then pull the lamp cover out.
Turn the bulb counterclockwise. Max. 40 W bulb for refrigerator is used and can be
purchased at a service center.
Vegetable
compartment
cover
2
To remove the vegetable compartment
cover, pull out the vegetable compartment
a bit to the front , lift the front part of the
vegetable compartment cover as shown by
, and take it out.
1
24
Care and maintenance
General information
Vacation time
During average length vacations, you will probably find it best to leave the refrigerator
in operation. Place freezable items in freezer for longer life.
When you plan not to operate, remove all food, disconnect the power cord, clean the
interior thoroughly, and leave each door OPEN to prevent odor formation.
Power failure
Most power failures that are corrected in an hour or two will not affect your
refrigerator temperatures.
However, you should minimize the number of door openings while the power is off.
If you move
Remove or securely fasten down all loose items inside the refrigerator.
To avoid damaging the height adjusting screws, turn them all the way into the base.
The outside wall of the refrigerator cabinet may sometimes get warm, especially just
after installation.
Don’t be alarmed. This is due to the anti-condensation pipe, which pumps hot
refrigerator to prevent “sweating” on the outer cabinet wall.
Anti
condensation
pipe
Cleaning
It is important that your refrigerator be kept clean to prevent undesirable odors. Spilled
food should be wiped up immediately, since it may acidify and stain plastic surfaces if
allowed to settle.
Exterior
Use a lukewarm solution of mild soap or detergent to clean the durable finish of your
refrigerator.
Wipe with a clean damp cloth and then dry.
Interior
Regular cleaning is recommended. Wash all compartments a baking soda solution or a
mild detergent and warm water. Rinse and dry.
After cleaning
Please verify that the power cord is not damaged, power plug is not overheated, or
power plug is well inserted into the power consent.
Warning
Always remove power cord from the wall outlet prior to cleaning in the vicinity of
electrical parts (lamps, switches, controls, etc.).
Wipe up excess moisture with a sponge or cloth to prevent water or liquid from
getting into any electrical part and causing an electric shock.
Never use metallic scouring pads, brushes, coarse abrasive cleaners, strong alkaline
solutions, flammable or toxic cleaning liquids on any surface.
Do not touch frozen surfaces with wet or damp hands, because damp object will stick
or adhere to extremely cold surfaces.
25
Care and maintenance
Trouble shooting
Before calling for service, review this list. It may save you both time and expense.
This list includes common occurrences that are not the result of defective
workmanship or materials in this appliance.
Occurrence
Possible cause
Solution
Runing of
refrigerator
Refrigerator
compressor
does not run.
Refrigerator
runs too much
or too long
Refrigerator control is off.
Set refrigerator control. See setting the
controls.
Refrigerator is in defrost cycle.
This is normal for a fully automatic
defrosting refrigerator. The defrost
cycle occurs periodically.
Plug at wall outlet is disconnected.
Make sure plug is tightly pushed into
outlet.
Power outage. Check house lights.
Call local electric company.
Refrigerator is larger than the previous
one you owned.
This is normal. Larger, more efficient
units run longer in these conditions.
Room or outside weather is hot.
It is normal for the refrigerator to work
longer under these conditions.
Refrigerator has recently been
disconnected for a period of time.
Large amounts of warm or hot food
may have been stored recently.
It takes some hours for the refrigerator
to cool down completely.
Doors are opened too frequently or too
long.
Warm food will cause the refrigerator to
run longer until the desired temperature
is reached.
Warm air entering the refrigerator
causes it to run longer. Open the door
less often.
Refrigerator or freezer door may be
slightly open.
Make sure the refrigerator is level.
Keep food and containers from
blocking door. See problem section.
OPENING/CLOSING of doors.
Refrigerator control is set too cold.
Set the refrigerator control to a
warmer setting until the refrigerator
temperature is satisfactory.
Refrigerator or freezer gasket is dirty,
worn, cracked, or poorly fitted.
Clean or change gasket. Leaks in the
door seal will cause refrigerator to run
longer in order to maintain desired
temperatures.
Thermostat is keeping the refrigerator
at a constant temperature.
26
This is normal. Refrigerator goes on and
off to keep the temperature constant.
Care and maintenance
Occurrence
Possible cause
Refrigerator
compressor
does not run.
Thermostat is keeping the refrigerator
at a constant temperature.
This is normal. The refrigerator goes on
and off to keep the temperature constant.
Freezer control is set too cold
Set the freezer control to a warmer
setting until the freezer temperature is
satisfactory.
Refrigerator control is set too cold.
Set the refrigerator control to a
warmer setting
Refrigerator control is set too cold.
See above solution.
Meat should be stored at a temperature
just below the freezing point of water (32˚F,
0˚C) for maximum fresh storage time.
It is normal for ice crystals to form due
to the moisture content of meat.
Freezer control is set too warm.
Set the freezer or refrigerator control to
a colder setting until the freezer or
refrigerator temperature is satisfactory.
Refrigerator control is set too warm.
Refrigerator control has some effect on
freezer temperature.
Set the freezer or refrigerator control to a
colder setting until the freezer or
refrigerator temperature is satisfactory.
Doors are opened too frequently or too
long.
Warm air enters the refrigerator/ freezer
whenever the door is opened.
Open the door less often.
Door is slightly open.
Close the door completely.
Large amounts of warm or hot food
may have been stored recently.
Wait until the refrigerator or freezer
has a chance to reach its selected
temperature.
Refrigerator has recently been
disconnected for a period of time.
A refrigerator requires some hours to
cool down completely.
Refrigerator control is set too warm.
Set the refrigerator control to a colder
setting.
Solution
Temperatures are
too cold
Temperature in the
freezer is too cold
but the refrigerator
temperature is
satisfactory.
Temperature in the
refrigerator is too
cold and the freezer
temperature
is satisfactory.
Food stored in
drawers freezes.
Meat stored in
fresh meat
drawer freezes.
Temperatures
are too warm
Temperatures in
the refrigerator
or freezer are
too warm.
Temperature in the
refrigerator
is too warm but
the freezer
temperature is
satisfactory.
27
Care and maintenance
Possible cause
Occurrence
Solution
Sound and noise
Louder sound
levels when
refrigerator is on.
Today’s refrigerators have increased
storage capacity and maintain more
even temperatures.
It is normal for sound levels to be higher.
Louder sound
levels when
compressor
comes on.
Refrigerator operates at higher pressures
during the start of the ON cycle.
This is normal. The sound will level off as
the refrigerator continues to run.
Vibrating or
rattling noise.
Floor is uneven or weak.
Refrigerator rocks on the floor when it is
moved slightly.
Be sure floor is level and solid and can
adequately support refrigerator.
Items placed on the top of the refrigerator
are vibrating.
Remove items.
Dishes are vibrating on the shelves in
the refrigerator.
It is normal for dishes to vibrate slightly.
Move dishes slightly.
Make sure refrigerator is level and firmly
set on floor.
Refrigerator is touching wall or cabinets.
Move refrigerator so that it does not
touch the wall or refrigerator.
The weather is hot and humid which
increases the rate of frost buildup
and internal sweating.
This is normal.
Door is slightly open.
See problem section opening/closing of
doors.
Door is opened too often or too long.
Open the door less often.
Weather is humid.
This is normal in humid weather.
When humidity is lower, the moisture
should disappear.
Door is slightly open,causing cold air
from the inside the refrigerator to meet
warm air from the outside.
This time, close the door completely.
Water/Moisture
/Ice inside
refrigerator
Moisture collects
on the inside walls
of the refrigerator.
Water/Moisture
/Ice outside
refrigerator
Moisture forms
on the outside of
the refrigerator
or between doors.
28
Care and maintenance
Occurrence
Possible cause
Solution
Odors in refrigerator
Interior needs to be cleaned.
Clean interior with sponge,warm water
and baking soda.
Food with strong odor is in the refrigerator.
Cover food completely.
Some containers and wrapping materials
produce odors.
Use a different container or brand of
wrapping materials.
Door(s) will not
close.
Food package is keeping door open.
Move packages that keep door from
closing.
Door(s) will not
close.
Door was closed too hard, causing other
door to open slightly.
Close both doors gently.
Refrigerator is not level. It rocks on the
floor when it is moved slightly.
Adjust the height adjusting screw.
Floor is uneven or weak.
Refrigerator rocks on the floor when it
is moved slightly.
Be sure floor is level and can adequately
support refrigerator.
Contact carpenter to correct sagging or
sloping floor.
Refrigerator is touching wall or cabinets.
Move refrigerator..
Food is touching shelf on top of the
drawer
Keep less food in drawer.
Track that drawer slides on is dirty.
Clean drawer and track.
Ice storage bin is empty.
When the first supply of ice is dropped
into the bin, the dispenser should operate.
Freezer temperature is set too warm.
Turn the freezer control to a higher
setting so that ice cubes will be made.
When the first supply of ice is made,
the dispenser should operate.
Household water line valve is not open.
Open household water line valve and
allow sufficient time for ice to be made.
When ice is made, dispenser should
operate.
Refrigerator or freezer door is not closed.
Be sure both doors are closed.
Opening/Closing of
doors/Drawers
Drawers are
difficult to move.
Dispenser
Dispenser will not
dispense ice
29
Care and maintenance
Occurrence
Possible cause
Dispenser will
not dispense
ice.
Ice has melted and frozen around auger
due to infrequent use, temperature
fluctuations and/or power outrages.
Remove ice storage bin, and thaw and
the contents. Clean bin, wipe dry and
replace in proper position.
When new ice is made, dispenser should
operate.
Ice dispenser
is jammed.
Ice cubes are jammed between the ice
maker arm and back of the bin.
Remove the ice cubes that are jamming
the dispenser.
Ice cubes are frozen together.
Use the dispenser often so that cubes do
not freeze together.
Ice cubes that have been purchased or
made in some other way have been
used in the dispenser.
Only the ice cubes made by the ice maker
should be used with the dispenser.
Household water line valve is not open.
See problem “Ice maker is not making
any ice.”
Open household water line valve.
Refrigerator or freezer door is not closed.
Be sure both doors are closed.
Water has been in the tank for too long.
Draw and discard 7 glasses of water
to freshen the supply. Draw and discard
an additional 7 glasses to completely rinse
out tank.
Unit not properly connected to cold
water line.
Connect unit to cold water line which
supplies water to kitchen faucet.
Dispenser will
not dispense
water.
Water has an
odd taste
and/or odor.
Solution
This sound is normally made when automatically made ice is dropped into ice storage
bin. Volume may vary according to refrigerator’s location.
Sound of ice
dropping
This sound is normally made when ice maker is supplied with water after dropping
the automatically made ice.
Sound of water
supply
Other
Please thoroughly read ‘Automatic ice maker and dispenser’ in this manual.
CUSTOMER ASSISTANCE NUMBERS:
http://www.lgservice.com
To Prove Warranty Coverage
Retain your Sales Receipt to prove date of purchase.
A copy of your Sales Receipt must be submitted at the time warranty service is provided.
To Obtain Product, Customer or Service Assistance
Call Toll-free for Customer Service
Tel : 1-877-714-7486
To Obtain Nearest Authorized Service Center
Call 1-877-714-7486, push option #1, 24 hours a day, 7days per week.
Please have your product type (Monitor, TV, VCR, MWO, Refrigerator) and ZIP code ready.
30
LG Twin Tower, 20, Yoido-Dong,
Youngdungpo-Gu, Seoul, 150-721, Korea.
http://www.lge.com
P/NO : 3828JD8792G
Printed in Korea
Download PDF

advertising