LG | LVC-C500 | User's Manual | LG LVC-C500 User's Manual

Operating Instructions
LVC-C500
LVC-C503
LVC-C510
LVC-C513
LVC-C530
LVC-C533
LVC-C553
Before installing and using the camera,
please read these instructions thoroughly and retain them for later reference.
Warning
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
2
To prevent fire or shock hazard,do not expose the unit to rain or moisture.
To avoid electrical shock,do not open the cabinet. Refer servicing to qualified personnel only.
Wiring methods shall be in accordance with the National Electric
Code, ANSI/NFPA 70.
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in the
cable entries of this product in the end user.
• Caution:Danger of explosion if battery is incorrectly replaced. Replaced
only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have smooth
well rounded surfaces or shall be provided with brushings.
Warning
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
Contents and Features
Contents
Features
Contents and Features . . . . . . . . . . . . . . . . . . . . . . . . .3
Cautions for Safe Operation . . . . . . . . . . . . . . . . . . . . . .4
Operating Controls and Their Functions . . . . . . . . . . .5
Power IN / CONTROL / External Key(A/D IN) . . . . .6-14
MENU DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . .15
CAMERA ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
FOCUS MODE SET . . . . . . . . . . . . . . . . . . . . . . .17-19
AWB SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21
AE SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24
AE LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
SPECIAL SET . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27
MOTION DET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
F OSD SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
P MASKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-32
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . .33-34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-36
The power zoom color video camera is designed for use in
monitoring system.
• High resolution and high sensitivity with a 1/4 inch
Exview/HAD/CCD (Charge Coupled Device)
• High magnitude of zoom lens with optical X 27,
Digital X 54 (LVC-C503/C513/C533/C553),
Digital X 324 (LVC-C500/C510/C530)
• Auto Focus / Auto White balance
• Auto exposure with DC Iris control
• Day & Night function
• DSS (Digital Slow Shutter) is available: Optional
• WDR (Wide Dynamic Range) is available: Optional
• Privacy Zones: Optional
3
Cautions for Safe Operation
Power Supply
This camera must always be operated a 12V DC
power supply.
Handling of the unit
Be careful not to spill water or other liquids on the
unit, or to get combustible or metallic material
inside the body. If used with foreign matter inside,
the camera is liable to fail, or to be a cause of fire
or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as light
fittings) for an extended period. Avoid operating or
storing the unit in the following locations.
• Extremely hot or cold places
(operating temperature 0°C-45°C)
• Damp or dust place
• Where it is exposed to rain
• Where it is subject to strong vibration
4
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Care of the unit
• Remove dust or dirt on the surface of the lens
with a blower.
• Use a dry soft cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity
of neutral detergent, then wipe dry.
• Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and insecticides.
They may damage the surface finish and/or
impair the operation of the camera.
Operating Controls and Their Functions
Model: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
1
2
1. Tripod adapter
This adapter can also be attached on the bottom of the camera.
2. Lens mount cap
3. TELE Key
When push the TELE KEY, picture is telephoto
4. WIDE Key
When push the WIDE KEY, picture is wide angle
5. Focus Near Key
In a manual situation, focus get near.
6. Focus Far Key
In a manual situation, focus get far.
7. Menu Key
If you want to set up a diverse function, you can push this button.
8. Video output (S-Video type)
Connect to the S-Video in connector of a monitor.
9. Interface of camera control JACK (6 Pin Din Jack Type)
• Connect to an external voltage controller
• You can supply a camera with power from this. (DC12V)
10. Video output (BNC type)
Connect to the video in connector of a monitor.
5
Power In / Control
Model: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
1
2
3
You can adjust focus and zoom by a pin terminal on the back side
of the camera.
6
5
4
* is the color of the cable. (If it is offered)
Adjust voltage from 1 pin and 2 pin
6
External Key (A/D IN)
Model: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
Schematic diagram of wired
remote-control
7
Operating Controls and Their Functions
Model: LVC-C530, LVC-C533
1. Tripod adapter
This adapter can also be attached on the bottom of the camera.
2. Lens mount cap
3. TELE Key
1
2
When push the TELE KEY, picture is telephoto
4. WIDE Key
When push the WIDE KEY, picture is wide angle
5. Focus Near Key
In a manual situation, focus get near.
6. Focus Far Key
In a manual situation, focus get far.
7. Menu Key
If you want to set up a diverse function, you can push this button.
8. Video output (S-Video type)
Connect to the S-Video in connector of a monitor.
9. Interface of camera control JACK (12 Pin Din Jack Type)
• Connect to an external voltage controller
• You can supply a camera with power from this. (DC12V)
10. Video output(BNC type)
Connect to the video in connector of a monitor.
8
Power In / Control
Model: LVC-C530, LVC-C533
You can adjust focus and zoom by a pin terminal on the back side
of the camera.
* is the color of the cable.(If it is offered)
9
Power In / Control
Model: LVC-C530, LVC-C533
10
External Key (A/D IN)
Schematic diagram of wired
remote-control
Model: LVC-C530, LVC-C533
11
Operating Controls and Their Functions
1. Tripod adapter
Model: LVC-C553
This adapter can also be attached on the bottom of the camera.
2. Lens mount cap
3. TELE Key
1
2
When push the TELE KEY, picture is telephoto
4. WIDE Key
When push the WIDE KEY, picture is wide angle
5. Menu Key
If you want to set up a diverse function, you can push this button.
6. Control JACK (RJ45)
Connect RS-422 interface
7. Focus Far Key
In a manual situation, focus get far.
8. Focus Near Key
In a manual situation, focus get near.
9. DC 12V screw terminal
Connect to an external power supply of DC 12V.
10. Hot Key
Use to day & night switching get mode.
11. Video output(BNC type)
Connect to the video in connector of a monitor.
12
Connections
Model: LVC-C553
1
Power Connection
2
1
3
2
1. Remove the insulation on the power cable as illustrated.
2. Attach the terminal tips.
3. Connect to the 12V DC UL Listed, Class 2 Power
Supply only on the camera.
Connection the monitor
1. To VIDEO OUT
2. To Video input on the monitor
13
Control
Model: LVC-C553
Remote Control Lines are connected to RJ-45 socket as
shown below.
In case of RS-485 INTERFACE (Basic)
T+
T-
CONTROL
7
T-
8
T+
RR+
CONTROL OUT
Controller
In case of Zoom/Focus DC control Interface(option)
PIN 8 PIN 1
4
ZOOM
ZOOM(+Tele, -Wide)
5
COMMON
COM
6
FOCUS
FOCUS(+Near, -Far)
Receiver/Controller
Voltage Range
14
+
Vcom + (+5~15V)
-
Vcom - (+5~15V)
MENU DESCRIPTIONS
Using TELE, WIDE, F. NEAR, F. FAR button
• TELE and WIDE are used for UP and DOWN.
• FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.
15
CAMERA ID
1. CAMERA ID
To connect a large number of camera , It can be
assigned to identification number to each camera for
camera control easily.
(OFF, 0 - 255: total numbers of ID are 256)
• It only can be set this function using ID commend.
To transfer ID Code of camera , In first byte at PC control.
Set the ID number of camera , and then the ID number
display continuously.
16
FOCUS MODE SET
2. Focus Set:
2-1. Focus Mode Set
This function is for focus mode setting
A) Set up “FOCUS SET” in main menu using Tele/Wide key.
Select the “FOCUS MODE” in submenu using Tele/Wide
key. And then set the mode (Auto, Push auto, or Manual)
using Focus key.
2-2. Focus Distance Set
This function is for selection of minimum shooting
distance.
A) Select the “FOCUS DIST” in submenu using Tele/Wide key.
B) Set the focus distance mode from 1cm to 5M. (1cm, 10cm,
50cm, 1M, 3M, 5M) using Focus key.
2-3. ZOOM START Set
This function is for selection of zoom start position.
A) Select the “ZOOM START” in submenu using Tele/Wide
key.
B) Set the Zoom start mode from x1 to x26 using Focus key.
17
FOCUS MODE SET
2-4. ZOOM END Set
This function is for selection of zoom end position.
A) Select the “ZOOM END” in submenu using Tele/Wide key.
B) Set the Zoom end mode using Focus key.
LVC-C503/C513/C533/C553: from (Zoom Start + 1) to X54
LVC-C500/C510: from (Zoom Start + 1) to X324
2-5. ZOOM SPEED Set
This function is for selection of zoom speed.
A) Select the “ZOOM SPEED” in submenu using Tele/Wide key.
B) Set the Zoom speed, Slow, Middle , Quick using Focus key.
2-6. ZOOM TRACKING MODE Set
This function is for selection of zoom tracking mode.
A) Select the “ZTRK” in submenu using Tele/Wide Command,
B) Set the Zoom tracking mode to Auto or Manual.
* Zoom tracking means focused zooming state.
18
FOCUS MODE SET
2-7. INITIAL SET
If initial mode set to ON, All FOCUS SET function is
changed to the factory setting.
A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF using Focus key.
2-8. RETURN TO MAIN MENU
This function is exit to main menu.
A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode using Focus key.
19
AWB SET (Auto White Balance)
3. AWB SET
3-1. WB Mode Set
This function is for changing the WB mode.
AWB
WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN
AUTO
NOT USE
NOT USE
ON
A) Set up “AWB SET” in main menu using Tele/Wide key.
B) Select the “WB MODE” in submenu using Tele/Wide key.
C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor using
Focus key.
*WBC MODE: Use for changing White Balance Mode .
1) AUTO: WB Range 2500°K ~ 9500°K .
2) PUSH AUTO: Set the AWB mode to Push Auto, then WB Mode
is auto.
3-2. RED ADJUST Set
This function is available for Manual WB mode.
This mode is the adjustment of user option for special color.
A) Select the “RED ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from (0-255 MANUAL) using Focus key.
20
AWB SET (Auto White Balance)
AWB
WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN
AUTO
NOT USE
NOT USE
ON
3-3. BLUE ADJUST Set
This function is available for Manual WB mode.
This mode is the adjustment of user option for special
color.
A) Select the “BLUE ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from (0-255 MANUAL) using Focus key.
3-4. PUSH AUTO
In case of PUSH AUTO WB mode.
Adjust the push auto mode ON, WB act automatically.
3-5. INITIAL SET
If initial mode set to ON, All AWB function is changed
to the factory setting
A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF using Focus key.
3-6. RETURN TO MAIN MENU
This function is exit to main menu.
A) Select the “RETURN “ in submenu. Using Tele/Wide key.
B) Set the return mode using Focus key.
21
AE SET (Auto Exposure)
4. AE SET
4-1. AE Mode Set
This function is for changing to AE mode.
A) Set up “AE SET” in main menu using Tele/Wide key.
B) Select the “AE MODE” in submenu using Tele/Wide key.
C) Set the mode auto, IRIS MAN, SLOW MAN, SHUTTER MAN,
Auto using Focus key
Note: SLOW MAN option is not available for LVC-C500,
LVC-C510, and LVC-C530.
4-2. IRIS ADJUST Set
This function is available for IRIS MAN mode.
A) Select the “IRIS ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.
4-3. AGC ADJUST Set
This function is available for SLOW MAN mode /
SHUTTER MAN mode .
A) Select the “IRIS ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 7 using Focus key.
22
AE SET (Auto Exposure)
4-4. BRIGHTNESS ADJUSTMENT Set
This function is available for AUTO mode.
A) Select the “BRIGHTNESS” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.
4-5. BACKLIGHT Set
Note: WDR option is not available
for LVC-C500, LVC-C510, and
LVC-C530.
4-6. E SENSITIVE
This function is available for SLOW mode / AUTO mode.
Area1
Area2
Area0
Area4
Auto BLC
A) Select the “BACKLIGHT” in submenu using Tele/Wide key.
B) Set the mode OFF, ON, or AUTO, WDR using Focus key.
* WDR (Wide Dynamic Range): It makes possible to capture both
high luminance and low luminance subject.
* Auto BLC (Auto back light compensation)
When a back light condition occurs in area1,area2, area3, or area4.
the back light compensation is enable. When the back light
condition disappears in that area, BLC is disable automatically.
If do not want this mode, set to OFF
Area3
A) Select the "E SENSITIVE" in submenu using Tele/Wide key.
B) • Adjust the level from X1 FIX to X20 FIX using Focus key.
(SLOW mode)
• Adjust the level from X1 AUTO to X20 AUTO using Focus key.
(AUTO mode)
23
AE SET (Auto Exposure)
4-7. FLICKERLESS Set
This function is available for AUTO mode.
A) Select the “FLICKERLESS” in submenu using Tele/Wide key.
B) Set the mode OFF, ON using Focus key.
* FLICKERLESS: Use for removing the flicker of picture
ON: Remove the flicker
(In case of PAL System: Shutter Speed 1/120 sec).
4-8. SHUTTER SPEED Set
This function is available for AUTO mode / SHUTTER
mode.
A) Select the “SHUTTER” in submenu using Tele/Wide key.
B) • Set the mode NORMAL, 1/120 - 1/50000 using Focus key.
(NTSC)
• Set the mode NORMAL, 1/125 - 1/50000 using Focus key.
(PAL)
4-9. INITIAL SET
A) Select the “INITIAL SET” in submenu using Tele/Wide Command.
B) Set the initial set mode to ON or OFF using Focus key.
4-10. RETURN TO MAIN MENU
This function is exit to main menu.
24
A) Select the “RETURN “ in submenu using Tele/Wide key.
B) Set the return mode using Focus key.
AE LEVEL (Auto Exposure)
5-1. BLC LEVEL Set
This function is for change to BLC LEVEL.
A) Select the “BLC LEVEL” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.
5-2. WDR LEVEL SET
This function is for change to WDR LEVEL.
A) Select the “WDR LEVEL” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 15 using Focus key.
5-3. INITIAL SET
A) Select the “INITIAL SET” in submenu using Tele/Wide
Command,
B) Set the initial set mode to ON or OFF using Focus key.
5-4. RETURN TO MAIN MENU
This function is exit to main menu.
A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode using Focus key.
25
SPECIAL SET
6. SPECIAL SET
6-1. User Title Set
This function is for custom title on screen display.
A) Set “SPECIAL SET” in main menu using Tele/Wide key.
B) Select the “USER TITLE” in submenu using Tele/Wide key.
C) Set the position of title and set data using Tele/Wide, Focus
key.
6-2. SHARPNESS ADJUST Set
A) Select the “SHARPNESS” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.
6-3. COLOR Set
This mode is for B/W mode.
A) Select the “COLOR” in submenu using Tele/Wide key.
B) Select the mode ON, OFF using Focus key.
6-4. NEGATIVE Set
This mode is to change color and luminance to
negative.
A) Select the “NEGATIVE” in submenu using Tele/Wide key.
B) Select the mode ON, OFF using Focus key.
26
SPECIAL SET
6-5. D EFFECT Set
This function is to scroll to mirror relevanced
function.
A) Select the “D EFFECT” in submenu using Tele/Wide key.
B) Set the mode, none, mirror, v-flip, rotation using Focus key.
6-6. INITIAL SET
If initial mode set to ON, All SPECIAL functions are
changed to the factory setting
A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
6-7. RETURN TO MAIN MENU
This function is exit to main menu.
A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode Using Focus key.
27
MOTION DET
7. MOTION DETECTION SET
7-1. DETECTION Mode Set
A) Set “MOTION” in main menu using Tele/Wide key.
B) Select the “DETECTION” in submenu using Tele/Wide key.
C) Set the mode ON, OFF using Focus key.
7-2. LEVEL ADJUST Set
This function is available for DETECTION mode.
A) Select the “LEVEL SET” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 21 using Focus key.
7-3. DAY/NIGHT Set
This function is available for DETECTION mode.
A) Select the “DAY/NIGHT” in submenu using Tele/Wide key.
B) Select a mode using Focus key (AUTO, DAY, NIGHT).
Note: This function is fixed to "DAY" for model LVC-C500/C503.
7-4. INITIAL SET
If initial mode set to ON, All MOTION functions are
changed to the factory setting
A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
7-5. RETURN TO MAIN MENU
This function is exit to main menu.
28
A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode Using Focus key.
F OSD DISP (Function On Screen Display)
8. F OSD DISP
8-1. FUNCTION Set
A) Set “F OSD” in main menu using Tele/Wide key.
B) Select the mode what you want in submenu using Tele/Wide
key.
C) Set the display mode of OSD ON, OFF using Tele/Wide,
FOCUS key.
*INITIAL SET and RETURN are the same as before procedure.
29
P MASKING (Privacy Masking)
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
9. P MASKING
9-1.AREA SEL
This function is to selecting to privacy masking area.
A) Set “P MASKING” in main menu using Tele/Wide key.
B) Select the “AREA SEL” in submenu using Tele/Wide key.
C) Select the area from area 1 to area 8 using Focus key.
9-2. Masking
This function is available for MASKING mode.
A) Select the “MASKING” in submenu using Tele/Wide key.
B) Select the mode ON/OFF using Focus key.
9-3. P MODE SET
This function is available to go to the PRIVACY
MASKING SETTING mode.
A) Select the “P MODE SET” in submenu using Tele/Wide key.
B) If PM SET END mode goes to ON, this menu automatically
goes OFF.
9-4. MOVE PT SET
Select to point which wants to move.
A) Select the “MOVE PT SET” in submenu using Tele/Wide key.
B) Select the mode ALL X, ALL Y, LEFT X, LEFT Y, RIGHT X,
RIGHT Y using focus key.
30
P MASKING (Privacy Masking)
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
9-5. MOVE PT CNT
This function is available to move selected point in the
MOVE PT SEL.
A) When MOVE PT SEL is selected ALL* : Available to move
area.
B) When MOVE PT SEL is selected LEFT* or RIGHT* : Change
the size of the area
9-6. PM SET END
Privacy Masking setting function is available to set OFF.
A) Select the “PM SET END” in submenu using Tele/Wide key.
B) If P MODE SET mode goes to ON, P MODE SET
automatically goes OFF.
9-7. INI COLOR
This function is to selecting to color of initial masking.
A) Select the “INI COLOR” in submenu using Tele/Wide key.
B) Select the mode from color 1 to color 8 using focus key.
9-8. COLOR
After setting, select the masking color.
A) Select the “COLOR” in submenu using Tele/Wide key.
B) Select the mode from color 1 to color 8 using focus key.
31
P MASKING (Privacy Masking)
9-9. INITIAL SET :
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
32
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
A) Select the “INITIAL SET” in submenu using Tele/Wide
Command,
B) Set the initial set mode to ON or OFF using Focus key.
9-10. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the “RETURN “ in submenu using Tele/Wide key.
B) Set the return mode using Focus key.
* You can not set “P MASKING” mode in the digital zoom
position.
On Screen Display
Some of these functions will
be displayed every time the
camera is operated and then
disappeared after 5 seconds.
1
2
3
6
FUNCTION
OSD Format
1. Focus Mode
Non display
Description
Auto Mode
Manual / push Auto Mode
2. Back Light
3. Shutter Speed
Non display
Back Light OFF
“BL”display
BLC ON / Auto BLC Mode
Non display
Normal Shutter (PAL: 1/50)
“Ff”display
Flickerless Mode
1/120 *
10 variable steps.
1/50,000
4. STAND-BY
Indicate the camera stand-by during the
camera’s power turning ON.
5. CAMERA ID
According to write the identification number to
each camera, Multi-point control is available
(PC Control 000~255).
* Shutter Speed 1/120 - 1/50000: NTSC
5
7 4
* Shutter Speed 1/125 - 1/50000: PAL
33
On Screen Display
FUNCTION
OSD Format
6. WBC Mode
Description
White Balance AUTO
WB Preset for INDOOR (3200°K)
Wb Preset for OUTDOOR (5100°K)
M
W
P
W
7. ZOOM Display
34
Manual WB Adjustment: In manual mode the HUE control is
available (0 ~ 255).
Push Auto White Balance: Turn this mode ON, the white trace
automatically. Turn this mode OFF, preserve the white of final
auto tracing action (Manual).
DX 54
Digital Zoom mode (LVC-C503/C513/C533/553)
DX 324
Digital Zoom mode (LVC-C500/C510/C530)
X 27
Optical Zoom mode
Specifications
Image device
1/4" EXVIEW HAD CCD
NTSC, High resolution : 811(H) X 508(V) 410K
Horizontal resolution
PAL, High resolution : 795 (H) X 596 (V) 470K
Approx. 520 TV Line.
Lens
X 27 Zoom (F 1.5 (W), F 3.8 (T) f= 3.25 ~ 88.0 mm), Video AF
Digital Zoom Ratio
X 2: Basic (OFF at WDR mode)
X 12: Basic (LVC-C500, LVC-C510, LVC-C530)
Minimum illumination
Normal Mode : 1 Lux (F 1.5, Normal Shutter)
(1/3 output)
Electronic Shutter Speed Mode :
0.01 Lux (X20 Field Accumulate)
Night Mode : 0 Lux (Infrared ON)
S/N
Scanning System
More than 48dB
2:1 Interlace
Scanning Frequency(H)
15.734 kHz (NTSC), 15.625 kHz (PAL)
Scanning Frequency(V)
60Hz (NTSC), 50Hz (PAL)
Privacy Zones
8 area active programmable zones
Specifications are subject to change without notice.
35
Specifications
Focal Length
3.24mm (WIDE), 86mm (TELE)
OSD(On Screen Display)
English
Power requirement
DC 12V
Video output
Composite Output 75Ω Terminated / Y,C Separated
Power consumption
5.4W: LVC-C503, LVC-C513, LVC-C533, LVC-C553
5.1W: LVC-C500, LVC-C510, LVC-C530
operating temperature
0°C - 45°C
Operating Humidity
0% RH - 60% RH
Storage temperature
-20°C - 60°C, 0% RH - 85% RH
Dimensions
57mm(W) X 62.4mm(H) X 98.5mm(D)
Weight
500g
Specifications are subject to change without notice.
P/NO: 3834RS0075A
36
‫ݷ‬ᔫᒎฉ
LVC-C500
LVC-C503
LVC-C510
LVC-C513
LVC-C530
LVC-C533
LVC-C553
在您使用此摄像机之前,请完整阅读此操
作指南以供参考。
வস
ቃቦ
电击危险请勿打开
ቃቦ : 为了减少电击的危险 请勿拆下前
盖 或后盖 内部没有任何用户可以维修
的零部件
如需维修 请联系专业维修人员
此符号用于警示用户,产品外壳存在
未绝缘的危险电压,会产生对人身造
成电击的危险。
为了防止电击事故,请不要将该产品暴露在雨中或潮湿的环境中。
为了避免电击的危险,请不要打开机壳,如需维修,请联系专业维
修人员。
接线方法应该符合美国国家电气规程 ANSI/NFPA 70 之规定
ਖࢾဉී
U.S.A
本产品经测试符合 FCC 第 15 部分有关 A 类数字设备的限制条件
这些限制条件是为提供合理的保护措施 防止在商业环境中安装设
备时产生有害干扰而制定的 本产品会产生 使用和辐射无线电频
率能量 如未正确安装和使用 可能对无线电通讯造成有害干扰
在住宅环境中使用此产品会产生有害干扰 在此情况下用户需要自
行采取措施消除此干扰
• 终端用户使用的此产品的电缆入口中提供了合适的导管引入装置
剔除装置或密封套
• 小心 : 如果电池更换不当 则会有爆炸的危险 请使用同一型号或
制造商建议的电池型号 请按照制造商的说明处置废旧电池
• 绝缘线穿过的金属孔应当具有光滑 圆形的表面 或者应当是刷
光的
此符号用于提醒用户,随设备一起提
供的印刷品中包含重要的操作和维护
(维修)指南。
வস
2
‫ޘ۾‬ອᆐ A ಢ‫ޘ‬ອăᏴᓕᐤણஹሆဧ፿‫ޘ۾‬ອဟLj჈భถ્‫ޘ‬ည
࢟ࠟছཷLjᏴࠥ༽ౚሆ፿ઓኊገ‫ݧ‬ནሤ።ࡼࡅဗă
ดྏਜ਼ᄂ࢛
෹ഺ
ᄂ࢛
ดྏਜ਼ᄂ࢛ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
‫ڔ‬ཝ‫ݷ‬ᔫᓖፀူሲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
࢟Ꮞၒྜྷ / ఼ᒜ / ᅪ‫ݝ‬୆ (A/D IN) . . . . . . . . . . . . . . . .6-14
‫࡝ݩ‬ႁී . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
摄像机 ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
对焦模式设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-19
AWB 设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21
AE 设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24
AE 级别 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
特殊设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27
运动检测 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
F OSD 显示 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
P MASKING (保密掩盖) . . . . . . . . . . . . . . . . . . . .30-32
ື෵‫࡝ݩ‬መာ (OSD) . . . . . . . . . . . . . . . . . . . . . . . . .33-34
ਖৃ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-36
此电动变焦彩色摄像机是为监视系统专门设计的。
• 高分辨率 高灵敏度的 1/4 英寸 Exview/HAD/CCD
电荷耦合装置
• 高倍数变焦镜头 光学变焦 X 27
数码变焦 X 54 (LVC-C503/C513/C533/C553),
数码变焦 X 324 (LVC-C500/C510/C530)
• 自动对焦 / 自动白平衡
• DC 光圈控制自动曝光
• 白天 & 黑夜功能
• DSS 数字慢速快门 : 可选
• WDR 宽动态范围 : 可选
• 保密区域 : 可选
3
‫ڔ‬ཝ‫ݷ‬ᔫᓖፀူሲ
࢟Ꮞ
此摄像机必须始终使用 12V DC 电源
‫ۃ‬Ꮵ࿳ስ૦
请注意不要将水或其它液体溅到摄像机内部 也不
要让可燃性物品或金属物品掉入摄像机内 如果摄
像机内部有杂质 则可能会导致摄像机故障或引发
火灾或电击
ဧ፿ਜ਼ࡀह࢐࢛
不要长时间观看过于明亮的物体
以下环境中使用或存放此设备
•
•
•
•
•
如灯具
避免在
过热或过冷的地方 工作温度 0°C-45°C)
潮湿或有灰尘的地方
有雨的地方
有强烈振动的地方
靠近有强电磁辐射的地方 如收音机或电视发射
机附近
4
࿳ስ૦ۣዸ
• 使用吹风机将表面的灰尘或脏物吹掉
• 请使用软布清洁机身 如果太脏 请使用带有少
量中性清洁剂的软布清洁 然后擦干
• 请不要使用挥发性溶剂 如稀释剂 酒精 苯和
杀虫剂 们会损坏表面或机身
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ
ቯ੓: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
1
2
1. ྯ୭ଦᓞ୻໭
此转接器还可以安装到摄像机的底部
2. ஻ᄿ‫ڔ‬ᓤঙ
3. TELE ୆
当按 TELE KEY 时
图像为远距拍摄
4. WIDE ୆
当按 WIDE KEY 时 图像为广角拍摄
5. ౯தୡ௦୆
在手动操作时
将焦距拉近
6. ౯Ꮠୡ௦
在手动操作时
将焦距拉远
7. ‫࡝ݩ‬୆
如果您要设置不同的功能
8. ၁ຫၒ߲
可按此键
S-Video ቯ
连接到监视器的 S-Video 输入接口
9. ࿳ስ૦఼ᒜ JACK ୻ా
6 ᑣ DIN JACK ቯ
• 连接到外部电压控制器
• 您可以通过此接口为摄像机供电
10. ၁ຫၒ߲
(DC12V)
BNC ቯ
连接到监视器的视频输入接口
5
࢟Ꮞၒྜྷ0఼ᒜ
ቯ੓: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
您可以通过摄像机背面的针形端子调节焦距和变焦。
变焦 & 焦距 DC 控制
1
2
3
6
5
4
A/D KEY 1 输入
共地变焦 & 对焦
通用地
电源输入 12V
* 为电缆颜色。(如果提供)
调节管脚 1 和管脚 2 的电压
6
ᅪ‫ݝ‬୆ (A/D IN)
ቯ੓: LVC-C500, LVC-C503,
LVC-C510, LVC-C513
线控示意图
7
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ
ቯ੓: LVC-C530, LVC-C533
1. ྯ୭ଦᓞ୻໭
此转接器还可以安装到摄像机的底部
2. ஻ᄿ‫ڔ‬ᓤঙ
3. TELE୆
1
2
当按 TELE KEY 时
图像为远距拍摄
4. WIDE୆
当按 WIDE KEY 时 图像为广角拍摄
5. ౯தୡ௦୆
在手动操作时
将焦距拉近
6. ౯Ꮠୡ௦
在手动操作时
将焦距拉远
7. ‫࡝ݩ‬୆
如果您要设置不同的功能
8. ၁ຫၒ߲
可按此键
S-Video ቯ
连接到监视器的 S-Video 输入接口
9. ࿳ስ૦఼ᒜ JACK ୻ా
12 ᑣ DIN JACK ቯ
• 连接到外部电压控制器
• 您可以通过此接口为摄像机供电
10. ၁ຫၒ߲
BNC ቯ
连接到监视器的视频输入接口
8
(DC12V)
࢟Ꮞၒྜྷ0఼ᒜ
ቯ੓: LVC-C530, LVC-C533
您可以通过摄像机背面的针形端子调节焦距和变焦。
用于 RS-232C 发送端口
用于 RS-232C 接收端口
变焦 & 焦距 DC 控制
通用地
遥控输入
用于运动检测脉冲输出
电源输入 12V
A/D KEY 1 输入
A/D KEY 2 输入
A/D KEY 3 输入
* 为电缆颜色。(如果提供)
9
࢟Ꮞၒྜྷ0఼ᒜ
ቯ੓: LVC-C530, LVC-C533
• RS232S ೌ୻
• ‫ܤ‬ୡ & ୡ௦ DC ఼ᒜೌ୻
୻၃໭࡝Ꮔ / ఼ᒜ໭
• ۨவၒ߲ Ꮵࣅଶ‫ހ‬ၒ߲
Ꮵࣅଶ‫ހ‬
10
൴ߡᄟୈ
ᅪ‫ݝ‬୆ (A/D IN)
线控示意图
ቯ੓: LVC-C530, LVC-C533
镜像
11
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ
1. ྯ୭ଦᓞ୻໭
ቯ੓: LVC-C553
此转接器还可以安装到摄像机的底部
2. ஻ᄿ‫ڔ‬ᓤঙ
3. TELE୆
1
2
当按 TELE KEY 时
图像为远距拍摄
4. WIDE୆
当按 WIDE KEY 时 图像为广角拍摄
5. ‫࡝ݩ‬୆
如果您要设置不同的功能
可按此键
6. ఼ᒜ‫( ఻ރ‬RJ45)
连接 RS-422 接口
7. ౯Ꮠୡ௦
在手动操作时
将焦距拉远
在手动操作时
将焦距拉近
8. ౯தୡ௦୆
9. DC 12V ൛ႋ࣡ᔇ
连接到 DC 12V 外部电源
10. ེ୆
使用此键切换白天 & 黑夜模式
11. ၁ຫၒ߲
BNC ቯ
连接到监视器的视频输入接口
12
ೌ୻
ቯ੓: LVC-C553
1
࢟Ꮞೌ୻
2
3
1. 如图所示去掉电源线外面的绝缘层
2. 装上端子头
3. 连接 12V DC UL Listed Class 2 电源到摄像机
ೌ୻ପ၁໭
1
2
1. 到 VIDEO OUT
2. 到监视器上的视频输入
13
఼ᒜ
ቯ੓: LVC-C553
遥控线连接到下面的 RJ-45 插孔
对于 RS-485 接口 基本
T+
T-
CONTROL
7
T-
8
T+
RR+
控制器
控制输出
对于变焦/对焦 DC 控制接口 可选
4
5
PIN 8 PIN 1
6
接收器/控制器
电压范围
14
+
Vcom + (+5~15V)
-
Vcom - (+5~15V)
‫࡝ݩ‬ႁී
ဧ፿ TELE WIDE F. NEAR F. FAR ‫ږ‬฽
• TELE 远摄 和 WIDE 广角 用于 UP 拉近 和 DOWN 拉远
• FOCUS+ 拉长焦距 和 FOCUS- 拉近减少 用于 INCREASE 增加
DECREASE 减少 数据
和
15
࿳ስ૦ ID
1. ࿳ስ૦ ID
当连接多台摄像机时 可以为每台摄像机指定一个识别
码 这样就可以更容易的对每台摄像机进行控制
(OFF, 0 - 255 ID 总数为 256)
• 只能使用推荐的 ID 来设置此功能
要发送摄像机的 ID 代码 使用 PC 控制的第一个字节
设置摄像机的 ID 编号 然后 ID 编号将连续显示
16
࣪ୡෝါ࿸ᒙ
2. ࣪ୡ࿸ᒙǖ
2-1. ࣪ୡෝါ࿸ᒙ
ࠥ৖ถ፿᎖࿸ᒙ࣪ୡෝါ
A)使用 Tele/Wide 键在主菜单中设置 FOCUS SET
使用 Tele/Wide 键选择子菜单中的 FOCUS MODE
然后
使用对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual (手动))
2-2. ࣪ୡ௦ಭ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋᔢቃ๜࿳௦ಭ
A) 使用 Tele/Wide 键选择子菜单中的 FOCUS DIST
B) 使用对焦键在 1cm 到 5M 之间设置对焦距离模式 (1cm,
10cm, 50cm, 1M, 3M, 5M)
2-3. ‫ܤ‬ୡఎဪ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡఎဪᆡᒙ
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM START
B) 使用对焦键在 x1 到 x26 之间设置变焦开始模式
17
࣪ୡෝါ࿸ᒙ
2-4. ‫ܤ‬ୡஉၦ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡஉၦᆡᒙă
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM END
B) 使用对焦键设置变焦结束模式
LVC-C503/C513/C533/C553:从 变焦开始 + 1 到 X54
LVC-C500/C510:从 变焦开始 + 1 到 X324
2-5. ‫ܤ‬ୡႥࣞ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡႥࣞă
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM SPEED
B) 使用对焦键设置变焦速度 Slow 低
Middle 中
2-6. ‫ܤ‬ୡৌᔍෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡৌᔍෝါ
A) 使用 Tele/Wide 命令选择子菜单中的 ZTRK
B) 将变焦跟踪模式设置为 Auto 自动 或 Manual 手动
* ‫ܤ‬ୡৌᔍᒎ௡ୡ‫ܤ‬ୡᓨზ
18
Quick 快
࣪ୡෝါ࿸ᒙ
2-7. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ
৖ถ୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
Ⴥᎌ FOCUS SET
࣪ୡ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
2-8. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
19
AWB ࿸ᒙ ᔈࣅ‫ڹ‬ຳੰ
3. ᔈࣅ‫ڹ‬ຳੰ࿸ᒙ
3-1. ‫ڹ‬ຳੰෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኀখ‫ڹ‬ຳੰෝါ
AWB
WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN
AUTO
NOT USE
NOT USE
ON
A) 使用 Tele/Wide 键在主菜单中设置 AWB SET
B) 使用 Tele/Wide 键选择子菜单中的 WB MODE
C) 使用对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual(手动) Outdoor(室外) Indoor(室内)
*WBC MODE: ፿᎖ኀখ‫ڹ‬ຳੰෝါ
1) AUTO 白平衡范围 2500 °K ~ 9500 °K
2) PUSH AUTO 将 AWB 模式设为 Push Auto 强制自动
平衡模式会自动调整
3-2. ੺ྻࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ Manual WB ၄ࣅ‫ڹ‬ຳੰ
ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ
ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 RED ADJUST
B) 使用对焦键调节值大小 0-255 MANUAL
20
则白
AWB ࿸ᒙ ᔈࣅ‫ڹ‬ຳੰ
3-3. ౸ྻࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ Manual WB ၄ࣅ‫ڹ‬ຳੰ
ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ
AWB
WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN
AUTO
NOT USE
NOT USE
ON
ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 BLUE ADJUST
B) 使用对焦键调节值大小 0-255 MANUAL
3-4. PUSH AUTO ༓ᒜᔈࣅ
Ᏼ PUSH AUTO WB ෝါሆ
୓༓ᒜᔈࣅෝါ࿸ᆐ ON WB ્ᔈࣅᒊቲ
3-5. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ
Ⴥᎌ AWB ᔈࣅ‫ڹ‬ຳੰ
৖ถ୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
3-6. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键设置返回模式
RETURN
21
AE ࿸ᒙ ᔈࣅ໎਒
4. ᔈࣅ௿ੰ࿸ᒙ
4-1. ᔈࣅ௿ੰෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኀখᔈࣅ௿ੰෝါă
A) 使用 Tele/Wide 键在主菜单中设置 AE SET
B) 使用 Tele/Wide 键选择子菜单中的 AE MODE
C) 使用对焦键设置模式为 IRIS MAN SLOW MAN SHUTTER MAN
注意 SLOW MAN 选项不适用于 LVC-C500 LVC-C510 和
LVC-C530
4-2. ਒མࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ IRIS MAN ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST
B) 使用对焦键在 0 到 255 中调整设置
4-3. ᔈࣅᐐፄ఼ᒜࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ SLOW MAN/SHUTTER MAN ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST
B) 使用对焦键在 0 到 7 中调整设置
22
AE ࿸ᒙ ᔈࣅ໎਒
4-4. ೡࣞࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ AUTO (ᔈࣅ) ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 BRIGHTNESS
B) 使用对焦键在 0 到 255 中调整设置
4-5. ۳਒࿸ᒙ
注意 WDR 选项不适用于 LVCC500 LVC-C510 和 LVC-C530
Area1
Area2
Area0
Area3
A) 使用 Tele/Wide 键选择子菜单中的 BACKLIGHT
B) 使用对焦键设置模式为 OFF ON 或 ATUO, WDR
* WDR 宽动态范围
用来捕捉高亮度或低亮度物体
* ᔈࣅ BLC ᔈࣅ۳਒‫ޡݗ‬
W当区域 1 区域 2 区域 3 或区域 4 中的背光满足条件时
可使用背光补偿 当此区域中的背光条件消失时 BLC 自动
停用 如果不需要此模式 将其设为 OFF
4-6. ᇄ࿑ႄ࿸ᒙ
ࠥ৖ถ፿᎖ SLOW ෝါ / AUTO ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 E SENSITIVE
B) • 使用对焦键在 X1 FIX 到 X20 FIX 之间设置 SLOW 模式
• 使用对焦键在 X1 AUTO 到 X20 AUTO 之间设置 AUTO 模式
Area4
ᔈࣅ BLC
23
AE ࿸ᒙ ᔈࣅ໎਒
4-7. ᇄ࿑ႄ࿸ᒙ
ࠥ৖ถ፿᎖ AUTO (ᔈࣅ) ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 FLICKERLESS
B) 使用对焦键设置模式为 OFF ON
* FLICKERLESS ᇄ࿑ႄ
፿᎖ሿ߹ᅄስ࿑ႄ
ON 开
去除闪烁
对于 PAL 制式 快门速度 1/120 秒
4-8. ౐ඡႥࣞ࿸ᒙ
ࠥ৖ถ፿᎖ AUTO ෝါ / SHUTTER ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 SHUTTER
B) • 使用对焦键设置模式为 NORMAL, 1/120 - 1/50000
• 使用对焦键设置模式为 NORMAL, 1/125 - 1/50000
4-9. ߱ဪ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
4-10. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键设置返回模式
24
RETURN
(NTSC)
(PAL)
AE ଀ܰ ᔈࣅ໎਒
5-1. ۳਒‫ܰ଀ޡݗ‬࿸ᒙ
ࠥ৖ถ፿᎖ኀখ BLC LEVEL
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键在 0 到 255 之间设置
BLC LEVEL
5-2. ౑ࣅზपᆍ଀ܰ࿸ᒙ
ࠥ৖ถ፿᎖ኀখ WDR LEVEL
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键在 0 到 15 之间设置
WDR LEVEL
5-3. ߱ဪ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
5-4. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键设置返回模式
RETURN
25
ᄂၐ࿸ᒙ
6. ᄂၐ࿸ᒙ
6-1. ፿ઓ‫ܪ‬ᄌ࿸ᒙ
ࠥ৖ถ፿᎖Ᏼື෵ᒦመာᔈࢾፃ‫ܪ‬ᄌ
A) 使用 Tele/Wide 键在主菜单中设置 SPECIAL SET
B) 使用 Tele/Wide 键选择子菜单中的 USER TITLE
C) 使用 Tele / Wide 和对焦键设置标题位置和数据
6-2. ༹ᇠࣞࢯᑳ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 SHARPNESS
B) 使用对焦键在 0 到 225 之间设置
6-3. ዕྻ࿸ᒙ
ࠥෝါ፿᎖੨‫ڹ‬ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 COLOR
B) 使用对焦键设置模式为 ON OFF
6-4. ঌᒋ࿸ᒙ
ࠥෝါ፿᎖୓ዕྻਜ਼ೡࣞখ‫ࡵܤ‬ঌᒋ
A) 使用 Tele/Wide 键选择子菜单中的 NEGATIVE
B) 使用对焦键设置模式为 ON OFF
26
ᄂၐ࿸ᒙ
6-5. D ቉ਫ࿸ᒙ
ᄰਭࠥ৖ถਦࣅጲመာሤਈ৖ถ
A) 使用 Tele/Wide 键选择子菜单中的 D EFFECT
B) 使用对焦键设置 mode none mirror v-flip rotation
6-6. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ
৖ถ୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
Ⴥᎌ SPECIAL
ᄂၐ
A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
6-7. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
27
Ꮵࣅଶ‫ހ‬
7. Ꮵࣅଶ‫ހ‬࿸ᒙ
7-1. ଶ‫ހ‬ෝါ࿸ᒙ
A) 使用 Tele/Wide 键在主菜单中设置 MOTION
B) 使用 Tele/Wide 键选择子菜单中的 DETECTION
C) 使用对焦键设置模式为 ON OFF
7-2. ଀ܰࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ DETECTION ON ෝါ
A) 使用 Tele/Wide 键选择子菜单中的
B) 使用对焦键在 0 到 21 之间设置
LEVEL SET
7-3.‫ڹ‬ᄖ/጗ᅵ࿸ᒙ
ࠥ৖ถ፿᎖ DETECTION ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 DAY/NIGHT
B) 使用对焦键选择一种模式 (AUTO, DAY, NIGHT)
注意 在 LVC-C500/C503 型号中 此功能固定为 DAY
7-4. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ
‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
Ⴥᎌ MOTION Ꮵࣅ
A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
7-5. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬ă
28
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
৖ถ୓
F OSD መာ ື෵መာ৖ถ
8. F OSD መာ
8-1. ৖ถ࿸ᒙ
A) 使用 Tele/Wide 键在主菜单中设置 F OSD
B) 使用 Tele/Wide 键在子菜单中选择您所需的模式
C) 使用 Tele / Wide 键和 FOCUS 键设置 OSD ON OFF 的显示
模式
*INITIAL SET ਜ਼ RETURN ࡼ‫ݛ‬ᒾᎧ༄ෂࡼ‫ݛ‬ᒾሤᄴ
29
P MASKING ۣමዚঙ
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
9. ۣමዚঙ
9-1.ཌᎮኡᐋ
此功能用于选择保密掩盖区域
A) 使用 Tele/Wide 键在主菜单中设置 P MASKING
B) 使用 Tele/Wide 键选择子菜单中的 AREA SEL
C) 使用对焦键在区域 1 到区域 8 中选择区域
9-2. ዚঙ
此功能用于 MASKING 模式
A) 使用 Tele/Wide 键选择子菜单中的 MASKING
B) 使用对焦键设置模式为 ON OFF
9-3. ۣමෝါ࿸ᒙ
此功能可转到 PRIVACY MASKING SETTING
盖设置 模式
保密掩
A) 使用 Tele/Wide 键选择子菜单中的 P MODE SET
B) 如果 PM SET END 模式转为 ON 此菜单自动转为 OFF
9-4. ጤࣅ࢛࿸ᒙ
选择要移动的点
A) 使用 Tele/Wide 键选择子菜单中的 P MODE SET
B) 使用对焦键选择 ALL X ALL Y LEFT X LEFT Y
RIGHT X RIGHT Y
30
P MASKING ۣමዚঙ
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
9-5. MOVE PT CNT
此功能可移动 MOVE PT SEL 中的选定点
A) 当 MOVE PT SEL 选择为 ALL* 时 可移动区域
B) 当 MOVE PT SEL 选择为 LEFT* 或 RIGHT* 时 改变区域
大小
9-6. ۣමዚঙ࿸ᒙஉၦ
保密掩盖设置功能可设为 OFF
A) 使用 Tele/Wide 键选择子菜单中的 PM SET END
B) 如果 PM SET END 模式转为 ON 则 P MODE SET 自动
转为 OFF
9-7. ߱ဪዕྻ
此功能用于选择初始掩盖的颜色
A) 使用 Tele/Wide 键选择子菜单中的 INI COLOR
B) 使用对焦键从颜色 1 到颜色 8 中选择模式
9-8. ዕྻ
设置完成后
选择掩盖颜色
A) 使用 Tele/Wide 键选择子菜单中的 COLOR
B) 使用对焦键从颜色 1 到颜色 8 中选择模式
31
P MASKING ۣමዚঙ
9-9. ߱ဪ࿸ᒙ :
P MASKING
AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN
32
NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
9-10. ऩૄᓍ‫ ࡝ݩ‬:
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
* 在数码变焦位置您不能设置 P MASKING 模式
ື෵‫࡝ݩ‬መာ (OSD)
以下某些功能在操作摄像机时
会在屏幕上显示 5 秒钟后消
失
৖ถ
OSD ৃါ
ႁී
1. 对焦模式
无显示
自动模式
☞
2. 背光
1
2
3
6
3. 快门速度
手动 / 强制自动模式
无显示
背光关闭
“BL”显示
背光补偿开 / 自动背光补偿模式
无显示
普通快门 (PAL: 1/50)
“Ff”显示
无闪烁模式
1/120 *
10 步
1/50,000
5
7 4
4. 待机
在电源打开过程中摄像机处于待机状态
5. 摄像机 ID
对每台摄像机设定识别码
制 PC 控制 000~255
* 快门速度 1/120 - 1/50000
* 快门速度 1/125 - 1/50000
可进行多点控
NTSC
PAL
33
ື෵‫࡝ݩ‬መာ (OSD)
৖ถ
OSD ৃါ
6. 白平衡控
ႁී
自动白平衡
制模式
室内白平衡预设 (3200°K)
室外白平衡预设 (5100°K)
7. 变焦显示
34
M
W
手动白平衡调整
P
W
强制自动白平衡 此模式打开时 白平衡自动调整
保留最后自动追踪的白平衡 手动
在手动模式下可使用 HUE 控制 (0 ~ 255)
DX 54
数码变焦模式 (LVC-C503/C513/C533/553)
DX 324
数码变焦模式 (LVC-C500/C510/C530)
X 27
光学变焦模式
此模式关闭时
ਖৃ
߅ስ࿸۸
1/4" EXVIEW HAD CCD
NTSC, 高分辨率 : 811(H) X 508(V) 410K
ၺຳॊ‫ܦ‬ൈ
大约 .520 TV Line
PAL, 高分辨率 : 795 (H) X 596 (V) 470K
஻ᄿ
X 27 变焦 (F 1.5 (W), F 3.8 (T) f= 3.25 ~ 88.0 mm), Video AF
ၫ൩‫ܤ‬ୡ
X 2: 基本 (WDR 模式下 OFF)
X 12: 基本 (LVC-C500, LVC-C510, LVC-C530)
ᔢቃᑍී
普通模式 : 1 Lux (F 1.5, 普通快门)
(1/3 ၒ߲)
电子快门速度模式 :
0.01 Lux (X20 场积累)
ቧᐅ‫܈‬
大于 48dB
ྸහᇹᄻ
ྸහຫൈ (H)
ྸහຫൈ (V)
ۣමཌᎮ
2:1 隔行
白天模式 : 0 Lux (红外开)
15.734 kHz (NTSC), 15.625 kHz (PAL)
60Hz (NTSC), 50Hz (PAL)
8 个区域激活可编程区域
ਖৃྦᎌৎখၭ‫ݙ‬഍ቲᄰᒀ
35
ਖৃ
ୡ௦
3.24mm (广角), 86mm (远景)
ື෵‫࡝ݩ‬መာ (OSD)
英语
࢟Ꮞገཇ
DC 12V
၁ຫၒ߲
复合输出75Ω 电阻 / Y,C 独立
৖੒
5.4W: LVC-C503, LVC-C513, LVC-C533, LVC-C553
5.1W: LVC-C500, LVC-C510, LVC-C530
৔ᔫᆨࣞ
0°C - 45°C
৔ᔫဘࣞ
0% RH - 60% RH
߼ࡀᆨࣞ
-20°C - 60°C, 0% RH - 85% RH
ߛࡁ
57mm(W) X 62.4mm(H) X 98.5mm(D)
ᒮ೟
500g
ਖৃྦᎌৎখၭ‫ݙ‬഍ቲᄰᒀ
P/NO: 3834RS0075A
36
Download PDF

advertising