LG | LW60 | User's Manual | LG LW60 User's Manual

Service Manual
(LW60/70)
LG Electronics
0
Contents
Ch 1. Service information
Ch 2. Locations
Ch 3. System information
· Specification
· Model configuration
· System Block Diagram
· Fn key combinations
· Status indicators
· BIOS Flash
· BIOS Setup
Ch 4. Symptom-to-part index
· Power system checkout
· Numeric error codes
· Error messages
· LCD-related symptoms
· Indeterminate problems
Ch 5. Removing and replacing a part (FRU)
Ch 6. Part list
· Part list
· Exploded view
1
Ch1. Service information
Chapter 1. Service information
1-1. Important service information
„ Strategy for replacing parts (FRU-Field Replaceable Units)
Before replacing parts
Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this
Use the following strategy to prevent unnecessary expense for replacing and servicing parts
1. If you are instructed to replacing a part but the replacement does not correct the problem, reinstall the
original part before you continue.
2. Some computers have both a processor board and system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
3. If an adapter or device consists of more than one part, any of the parts (FRUs) may be the cause of the
error. Before replacing the adapter or device, remove the parts (FRUs), one by one, to see if the
symptoms change. Replace only the part that changed the symptoms.
Caution
The BIOS configuration on the computer you are servicing may have been customized.
Running Automatic Configuration my alter the settings. Note the current configuration settings;
then, when service has been completed, verify that those settings remain in effect.
„ Strategy for replacing a hard-disk drive
You have to get a User’s approval before formatting or replacing a hard-disk drive. You must let the User
know that the user is responsible for the loss data
Caution
The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an
incorrect drive, data or programs can be overwritten.
2
Ch1. Service information
1-2. Safety notices
Warning
Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs,
and other small parts are in place and are not left loose inside the computer. Verify this by
shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause
electrical shorts.
Warning
some standby batteries contain a small amount of nickel and cadmium. Do not disassemble
a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery
as required by local ordinances or regulations. Use only the battery in the appropriate parts
listing. Use of an incorrect battery can result in ignition or explosion of the battery
Warning
The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or
water, or short-circuit it. Dispose of the battery pack as required by local ordinances or
regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Use of an incorrect battery can result in ignition or explosion of the battery.
Warning
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands,
immediately was the affected areas with water for at least 15 minutes. Seek medical care if any
symptoms from the fluid are present after washing.
Warning
To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.
Warning
Though the main batteries have low voltage, a shorted or grounded battery can produce enough
current to burn personnel or combustible materials.
Warning
Before removing any part (FRU), turn off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
3
Ch1. Service information
1-3. Safety information
„ General safety
Follow these rules to ensure general safety
· Observe good housekeeping in the area of the machines during and after maintenance.
· When lifting any heavy object
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles
(This action removes the strain from the muscles in your back.)
· Do not attempt to lift any object weights more then 16kg(35lb) or object that you think are too heavy for you.
· Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
· Before you start the machine, ensure that other service representatives and the customer’s personnel are
not in a hazardous position.
· Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
· Keep your tool box away from walk areas so that other people will not trip over it.
· Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
· Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately
8 centimeters(3 inches) from the end.
· Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for you clothing.
· Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
· After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
· Reinstall all covers correctly before returning the machine to the customer.
Caution
Metal objects are good electrical conductors.
4
Ch1. Service information
„ Electrical safety
Observe the following rules when working on electrical equipment.
Important
Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive
fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from
electrical shock.
· Find the room emergency power-off switch, disconnecting switch, or electrical outlet. If an electrical outlet.
If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
· Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
· Disconnect all power before
1. Performing a mechanical inspection
2. Working near power supplies
3. Removing or installing main units
· Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
· If you need to work on a machine that has exposed electrical circuits, observe the following precautions :
Ensure that another person, familiar with the power-off controls, is near you.
Caution
Another person must be there to switch off the power, if necessary.
· Use only one hand when working with powered-on electrical equipment. Keep the other hand in your
pocket or behind your back
Caution
An electrical shock can occur only when there is a complete circuit. By observing the above rule,
you may prevent a current from through your body.
· When using testers, set the controls correctly and use the approved probe leads and accessories for that
tester
5
Ch1. Service information
· Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal
floor strips and machine frames.
· Observe the special safety precautions when you work with very high voltages. These instructions are in
the safety sections of maintenance information. Use extreme care when measuring high voltages.
· Regularly inspect and maintain your electrical hand tools for safe operational condition.
· Do not use worn or broken tools and testers.
· Never assume that power has been disconnected from a circuit. First check that it has been powered off.
· Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
non-grounded power extension cables, power surges, and missing safety grounds.
· Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive such touching can cause personal injury and machine damage.
· Do not service the following parts with the power on when they are removed from their normal operating
places in a machine.
1. Power supply units
2. Pumps
3. Blowers and fans
4. Motorgenerators
and similar units. (This practice ensure correct grounding of the units.)
· If an electrical accident occurs
1. Use caution ; do not become a victim of yourself.
2. Switch off power.
3. Send another person to get medical aid.
6
Ch1. Service information
„ Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions.
As each machine was designed and built, required safety items were installed to protect users and service
personnel from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-LG features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
· Consider these conditions and the safety hazards they present
1. Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
2. Mechanical hazards, such as loose or missing hardware
Refer to the following checklist and begin the checks with the power off, and the power cord disconnected.
· Checklist
1. Check exterior covers for damage (loose, broken, or sharp edges)
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for :
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity
for 0.1
or less between the external ground pin and frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG
alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screw or rivets) have not been removed or tampered with.
7
Ch1. Service information
„ Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between
objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Note
Use product-specific ESD procedures when they exceed the requirements noted here.
Make sure that the ESD protective devices you use have been certified (ISO9000) as fully effective.
· When handling ESD-sensitive parts :
1. Keep the parts in protective packages until they are inserted into the product.
2. Wear a grounded wrist strap against your skin to eliminate static on your body.
3. Prevent the part from touching your clothing. Most clothing retains a charge even when you are wearing
a wrist strap.
4. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
5. Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note
The use of a grounding system is desirable but not required to protect against ESD damage.
a. Attach the ESD ground clip too any frame ground, ground braid, or green-wire ground.
b. Use an ESD ground or reference point when working on a double-insulated or battery-operated
system. You can use coax or connector-outside shells on these systems.
c. Use the round ground-prong of the AC plug on AC-operated computers.
„ Grounding requirements
Electrical grounding of the computers is required for operator safety and correct system function.
Proper grounding of the electrical outlet can be verified by a certified electrician.
8
Ch1. Service information
1-4. Laser compliance statement
When a CD-ROM drive, DVD drive or the other laser product is installed, note the following :
Caution
Use of controls or adjustments or performance of procedures other than those specified here in
might result in hazardous radiation exposure.
Opening the CD-ROM drive, DVD-ROM drive or the other optical storage device could result in exposure
to hazardous laser radiation.
There are no serviceable parts inside those drives. Do not open
Danger
Emits visible and invisible laser radiation when open. Do not stare into the beam , do not view
directly with optical instruments, and avoid direct exposure to the bean.
1-5. Backup (Standby) RTC battery safety information
When replacing or disposing of the backup (standby) RTC battery, note the following :
9
Ch1. Service information
1-6. Read this first
Before you go to the checkout guide, be sure to read this section.
Important Notes
·
Only trained personnel certified by LG should service the computer.
·
Read the entire FRU removal and replacement page before replacing any FRU.
·
Use new nylon-coated screws when you replace FRUs.
·
Be extremely careful during such write operations as copying, saving, formatting.
Drives in the computer that you are servicing sequence might have been altered. If you selected an
incorrect drive, data or programs might be overwritten.
· Replace FRUs only for the correct mode.
· When you replace a FRU, make sure the model of the machine and the FRU part number are correct by
referring to the FRU parts list.
· A FRU should not be replaced because of a single, irreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hard ware defect, such as cosmic radiation,
electrostatic discharge, or software errors.
· Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the
error log and run the test again. If the error does not recur, do not replace the FRU.
· Be careful not to replace a non-defective FRU.
„ What to do first
You must fill out the record form first.
During the warranty period, the customer may be responsible for repair costs if the computer damage was
caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. The following list provides some common items that are not covered under
warranty and some symptoms that might indicate that the system was subjected to stress beyond normal
use. Before checking problems with computer, determine whether the damage is covered under the
warranty by referring to the following :
10
Ch1. Service information
The followings are not covered under warranty :
· CD
panel cracked from the application of excessive force or from being dropped
·
Scratched (cosmetic) parts
·
Distortion, deformation, or discoloration of the cosmetic parts
·
Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessive
force
·
Damage caused by liquid spilled into system
·
Damage caused by improper insertion of a PC Card or the installation of an incompatible card
·
Damage caused foreign material in the diskette drive
·
Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette
with multiple labels
·
Damaged or bent diskette eject button
·
Fusses blown by attachment of a non-supported device
·
Forgotten computer password (making the computer unusable)
·
Sticky keys caused by spilling a liquid onto the keyboard
The following symptoms might indicate damage caused by non-warranted activities :
·
Missing parts might be a symptom of unauthorized service or modification.
·
If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or
dropped.
11
Ch2. Locations
Chapter 2. Locations
„ Front view (15.4")
LCD latch
LCD latch
WLAN Antenna
WLAN Antenna
Mute
LCD
Volume Up
Volume Down
Power switch
DVD, MUSIC
Keyboard
TouchPad
Built-in MIC
TouchPad button
Built-in Speaker
Built-in Speaker
Remote Control Receiver
12
Ch2. Locations
„ Front view (17.1")
LCD latch
LCD latch
WLAN Antenna
WLAN Antenna
Mute
LCD
Volume Up
Volume Down
Power Switch
DVD, MUSIC
Keyboard
TouchPad
TouchPad button
Built-in MIC
Built-in Speaker
Built-in Speaker
Remote Control Receiver
13
Ch2. Locations
„ Rear view (15.4", 17.1")
USB connector
LAN connector
Line in / S/PDIF
Modem connector
S-VIDEO connector
AC connector
„ Left view (15.4", 17.1")
Parallel connector
Express Card eject button
Express Card slot
4-in-1 Card slot
VGA connector
Fan louvers
PC Card eject button
PC Card slot
„ Right view (15.4", 17.1")
Headphone connector
IEEE 1394 connector
MIC connector
IrDA port
ODD eject button
ODD
Security key hole
Emergency eject hole
USB connector
Security key hole (Kensington Lock)
User can attach a separately purchased chain lock into the security keyhole and connect it to a fixed object
to prevent a notebook theft
Emergency eject hole
Insert a thin and hard pin into this hole, and you can open the disc tray manually.
14
Ch3. System information
Chapter 3. System information
„ Specification
- CPU
· Dothan 1.6 ~ 2.1 GHz
· μFCBGA
- Main Chipset & Graphic
· Intel 915GM,ICH6-M
· Intel 915PM, ICH6-M, ATI Mobility Radeon X600 VGA Controller
- Memory
· 2SODIMM – Up to 2GB
· DDR2 PC2-3200S/4200S Capable (400/533MHz)
- HDD
· 2.5” 9.5mm 40/60/80GB PATA Type
- Communication
· Modem, Daughter Card Type
· Marvell Yukon PCI-E 10/100 Ethernet Controller on Board
- Wireless LAN Solution
· 802.11bg/abg Mini PCI Type, Quad-band Antenna
- Card Slot
· Express Card Slot
· 4-in-I Card Slot (Memory Stick, Memory Stick Pro, Multi Media Card, SD Card)
- ODD
· Fixed Optical Storage
· DVD-COMBO, Super-Multi Drive
- Port
· VGA, 4X USB(2.0), RJ11, RJ45, Headphone-out/SPDIF, Mic-in, AC-in, IEEE1394, S-Video
- Input Devices
· Keyboard : 99Key Keyboard
· Touchpad
- Buttons
· Power, Volume Down, Volume Up, Mute, DVD, MUSIC
- Indicator (LED)
· AC-in, Power On, Charge, HDD, Caps Lock, Num Lock, Wireless
- Power
· 90 Watt 19V 4.74A Adapter
- Audio
· C-Media Azalia Audio Codec, Stereo speakers 1.2W - LW60, 1.8W+2W(Woofer) - LW70
- Battery
· 6 Cell 4.8AHr, CYLINDRICAL (Li-Ion)
· 9 Cell 7.2AHr, CYLINDRICAL (Li-Ion)
15
16
D
C
B
A
page52
SPDIF
1
page32
AMP
1.8V
SPDIF
page37
page35~36
1.5V
3.3V
2
LINE-IN
LINE-OUT
MIC-IN
LAN
page47
EXPRESS CARD
(GbE)
88E8053
(10/100)
Magnetic
page37
88E8036
DIGITAL(3.3V)
AC’97 / AZALIA
DDR2 400/533 MHz
PORT 3
PORT 1
PIO
page40
PIO
SIO
3
Sub BD
IrDA
SIO
page40
LPC47N217
3.3V
3
page 2 - 4
page39
4
3.3v
page42
TOUCH PAD
4
page41
H8S/2110B
PCI 3.3V,33MHz
PATA 66/100
PATA 66/100
SATA 150
THERMAL
SENSOR
3.3V
page 5
PR CONNECTOR
3.3V
FWH
LPC 3.3V, 33MHz
page23-28
ICH6-M
DMI
page 6-12
GMCH_CORE (1.05V)
ALVISO-GM
CPU_IO
FSB 533MHz
CPU_IO
CPU_CORE
DOTHAN
HUNTER-W
PCI EXPRESS
page32
MDC MODEM
5V
page31
CMI9880
AUDIO
CODEC
page13-15
SODIMM-0/1
DDR2
page35
1.2V
2.5V
3.3V
page33
Sub AMP
5V
page33
LINE-IN
H/P OUT
Mic IN
SPDIF
DDR2 THERMAL
SENSOR
3.3V
page15
page22
CK-SSCD
page22
CK-410M
VPD EEPROM
page33
Int. MIC
page34
WOOFER
page32
Int. SPK
RJ11/45 CONN
LINE-IN
LINE-OUT
MIC-IN
page58
V2.5S / V2S_ATI
page51
Miscellaneous
page52
ACIN LOGIN
CHARGER LOGIC
5V/3.3V
SYSTEM DC/DC
page54
DDR2 DC/DC
page55
GMCH_CORE
CPU_IO
page57
V1.2S / V1.5A
page53
CPU CORE VCC
2
ANALOGVCC(5V)
TV/CRT/LVDS
1
page20
page21
CRT CONN
SUB BD
page29
5V
5V
page 33
SUB BOARD
USB2/3
USB2/3
USB4/5
USB7
USB6
USB0/1
AD16
PIRQA,SERIRQ
PCIREQ/GNT0
AD18
PIRQC/D
PCIREQ/GNT3
1394
Power LED
Wireless LED
Remocon
page42
INT. KBD
USB Interface
page29
CD-ROM
page29
PATA HDD
3.3V
SATA HDD
3.3V
S-VIDEO CONN
5V
3.3V
LCD CONN
page 5
FAN CONN
5V
page43
5
1394
SUB BD
page34
page42
USB4/5
USB7
(Remocon)
(Express card) page47
USB6
page30
page47
page47
4 in 1 CARD
SD/MMC
MS/MSPRO
3.3V
5V
CARD BUS
page 42
6870
2004.12.3
PART NO
DATE
6
SHEET
REV
1
of 59
0.9
HUNTER-W 15.4" & 17.1" WIDE
BLOCK DIAGRAM
PC Division
SUB BOARD
MUTE
VOLUME DOWN
VOLUME UP
INSTANT AUDIO
INSTANT DVD
LEDs & Button
CAPS/NUM
ACIN
CHG
PWR
LAN
PWR
6
LG Electronics Inc
page44
page38
TITLE
PCI7420
USB0/1
3.3V
3.3V
MINI PCI CONN
5
A4
D
C
B
A
Ch3. System information
„ System Block Diagram (GM)
17
D
C
B
A
page52
SPDIF
1
page32
AMP
1.8V
SPDIF
page37
page35~36
1.5V
3.3V
2
LINE-IN
LINE-OUT
MIC-IN
LAN
page47
EXPRESS CARD
(GbE)
88E8053
(10/100)
Magnetic
page37
88E8036
DIGITAL(3.3V)
AC’97 / AZALIA
DDR2 400/533 MHz
PORT 3
PORT 1
PIO
page40
PIO
SIO
3
Sub BD
IrDA
SIO
page40
LPC47N217
3.3V
3
page 2 - 4
page39
4
3.3v
page42
TOUCH PAD
4
page41
H8S/2110B
PCI 3.3V,33MHz
PATA 66/100
PATA 66/100
SATA 150
THERMAL
SENSOR
3.3V
page 5
PR CONNECTOR
3.3V
FWH
LPC 3.3V, 33MHz
page23-28
ICH6-M
DMI
page 6-12
GMCH_CORE (1.05V)
ALVISO-PM
CPU_IO
FSB 533MHz
CPU_IO
CPU_CORE
DOTHAN
HUNTER-W
PCI EXPRESS
page32
MDC MODEM
5V
page31
CMI9880
AUDIO
CODEC
page13-15
SODIMM-0/1
DDR2
page35
1.2V
2.5V
3.3V
page33
Sub AMP
5V
page33
LINE-IN
H/P OUT
Mic IN
SPDIF
DDR2 THERMAL
SENSOR
3.3V
page15
page22
CK-SSCD
page22
CK-410M
VPD EEPROM
page33
Int. MIC
page34
WOOFER
page32
Int. SPK
RJ11/45 CONN
LINE-IN
LINE-OUT
MIC-IN
page58
V2.5S / V2S_ATI
page51
Miscellaneous
page52
ACIN LOGIN
CHARGER LOGIC
5V/3.3V
SYSTEM DC/DC
page54
DDR2 DC/DC
page55
GMCH_CORE
CPU_IO
page57
V1.2S / V1.5A
page53
CPU CORE VCC
2
ANALOGVCC(5V)
TV/CRT/LVDS
1
page20
page21
CRT CONN
PEG INTERFACE
SUB BD
5V
5V
page29
page 33
SUB BOARD
USB2/3
USB2/3
USB4/5
USB7
USB6
USB0/1
AD16
PIRQA,SERIRQ
PCIREQ/GNT0
AD18
PIRQC/D
PCIREQ/GNT3
1394
Power LED
Wireless LED
Remocon
page42
INT. KBD
USB Interface
page29
CD-ROM
page29
PATA HDD
3.3V
SATA HDD
3.3V
S-VIDEO CONN
5V
3.3V
LCD CONN
page 5
FAN CONN
5V
TV/CRT/LVDS
(1.2V)
page43
5
1394
SUB BD
page34
page42
USB4/5
USB7
(Remocon)
(Express card) page47
USB6
page30
page47
page47
4 in 1 CARD
SD/MMC
MS/MSPRO
3.3V
5V
CARD BUS
page 42
6870
2004.12.3
PART NO
DATE
6
SHEET
REV
1
of 59
0.9
HUNTER-W 15.4" & 17.1" WIDE
BLOCK DIAGRAM
PC Division
SUB BOARD
MUTE
VOLUME DOWN
VOLUME UP
INSTANT AUDIO
INSTANT DVD
LG Electronics Inc
page44
page38
TITLE
PCI7420
USB0/1
3.3V
3.3V
6
LEDs & Button
CAPS/NUM
ACIN
CHG
PWR
LAN
PWR
page 16-19
M24CSP
MINI PCI CONN
5
A4
D
C
B
A
Ch3. System information
„ System Block Diagram (PM)
Ch3. System information
„ Fn key combinations
The following table shows the function of each combination of Fn with a function key.
Function of Fn keys has nothing to do with Operating System.
[Fn] +
Description
[F1]
User-defined Hot key. (Setting is available at OSD)
[F2]
User-defined Hot key. (Setting is available at OSD)
[F3]
User-defined Hot key. (Setting is available at OSD)
[F4]
Force the computer to enter power-saving mode. (ex: system standby and hibernation)
[F5]
TouchPad Disable (Impossible to use TouchPad) / TouchPad Enable (Possible to use
TouchPad) / TouchPad Auto-Disable (When connecting USB mouse to the computer,
TouchPad is disable) The TouchPad initialization takes 1~2 seconds, so wait for the
Initialization to end before using the TouchPad.
[F6]
Wireless LAN on / off
[F7]
When the computer is attached to an external monitor, you can changed the display output
location with [Fn] + [F7] combination. You can switch to and from the three types of display
modes, LCD display only, the external monitor only, or both at the same time.
[F8]
Enable/Disable Auto Sound power management (battery mode only).
[F9]
Enable/Disable Auto Brightness control.
[F10]
System information
[ESC]
Maximum power-saving mode. (when OSD is installed)
[ScrLk]
Number lock
[Delete]
Brightness up
[Insert]
Brightness down
PgUp
PgDn
Home
End
[F12]
Maximum power-saving mode.
18
Ch3. System information
„ Status indicators
The system status indicators show the status of the computer
1
3
2
4
5
6
7
1. Caps lock
Caps lock indicator lights up when the Caps lock key is pressed.
When this indicator lights up, you can type capital letters without pressing the Shift key.
2. Num lock
Num lock indicator lights up when the combination of the Fn and Num lock key is pressed.
When this indicator lights up, you can use the embedded numeric keys.
(To use the numeric keys, you must enable the Internal Keypad setting under the Advanced menu in the BIOS
Setup Utility.)
3. Wireless activity indicator
Wireless activity indicator indicates the following.
Off: Wireless LANis off.
Blinking(3-4 Seconds): Searching for Access point for Wireless LAN Connection.
Blinking (short interval): Data is transferring with Wireless LAN is on.
4. AC Power
Power indicator lights up when the power cord is connected to the computer.
5. Power
Power status indicator indicates the following status of the computer.
Green: The computer is turned on.
Off: The computer is turned off or is in hibernation mode.
Blinking: The computer is in standby mode.
6. Battery
Battery status indicator indicates the following status of the battery.
Green: The computer is connected to an AC adaptor and is being charged.
Off: The battery is fully charged OR the computer is not connected to an AC Adapter.
Blinking: The battery power is under 10% of its maximum capacity or battery occurs.
Battery tribe warning blinks as user defined from 'Battery Miser'.
7. Drive in use
Drive in use indicator lights up when data is being written to or read from the hard disk or optical disk drive.
19
Ch3. System information
„ BIOS Flash
You can update BIOS using a floppy disk drive.
Because this system is not equipped with any floppy disk drive, you have to use an external USB drive for
a BIOS update. In order to boot up with an USB drive, please set Removable Device as the first boot up
drive in the boot menu of BIOS setup.
· How to update flash ROM in DOS
1. Create ‘boot up’ flash update diskette.
2. Copy a ROM image file (*.wph) into the root of the flash update diskette.
3. Copy phlash16.exe to the flash update diskette.
4. Insert the diskette into the FDD of your computer.
5. Boot your computer with the diskette, and type ‘phlash16*.wph/mode=n’.
6. Cold boot and follow the instruction displayed on the screen.
· Flash options /mode=n
0 – Default mode. Keep the current DMI information and update BIOS image only.
1 – Update DMI information only.
If new DMI information is not specified, the current DMI information is left unchanged.
2 – Update BIOS and DMI information.
If new DMI information is not specified, the current DMI information is left unchanged.
3 – Update BIOS and DMI information.
DMI information is updated to the DMI string and options specified in the new BIOS image.
Note
DMI is Desktop Management Interface
20
Ch3. System information
„ How to update flash ROM in Windows
1. Quit all running programs.
2. Start WINPHLASH.EXE.
3. Select the procedure you want :
a. Backup BIOS and Flash BIOS with new settings
b. Backup BIOS Only
4. Specify the locations for backup and new BIOS files in BIOS Setting Locations.
a. Enter the name of the backup file for existing BIOS or click Browse to locate the file.
b. Enter the name of the new BIOS file or click Browse to locate the file.
5. Click Advanced Settings button to access the advanced settings
6. Click Flash BIOS button to start flash BIOS.
7. Wait for the operation to complete. WinPhlash may take one or two minutes to complete flash BIOS
operation.
21
Ch3. System information
8. After the completion, ‘System BIOS was successfully updated’ appears on the screen, then the
computer restarts.
9. After the restart, make sure the system BIOS is updated.
10. If your computer does not restart automatically, turn off your computer and then turn it back on by
pressing power button.
22
Ch3. System information
„ BIOS Setup
BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM, and
check the configurations during startup. Use the BIOS Setup Utility to change and save the system
environment, hardware configurations, power saving mode, etc.
· Open the BIOS Setup Utility in the following situations :
1. to change the BIOS setup
2. to replace the backup battery
3. system configuration error occurs
4. to change the boot order
5. to set/change a password
Press the power button.
When the LG logo appears on the screen, press
and enter the BIOS Setup Utility.
23
Ch3. System information
„ Using the keys
The keys used in the BIOS Setup Utility and their functions are described at the bottom.
·
,
+
: General Help
Display the descriptions of the keys used in the setup utility.
·
,
: Select Item
Navigate and select items in the setup utility. The selected item becomes highlighted.
·
,
: Select Menu
Move to another menu.
·
/
,
: Change Values
Change the value of a selected item.
·
: Load Default Configuration
Display Setup Confirmation window. Press Enter to load default configuration.
·
: Select Sub-Menu
Some items have sub-menus. Display the sub-menu for a selected item.
·
: Save and Exit
Display Setup Confirmation window. Press Enter to save and exit.
·
: Exit
In a sub-menu, press Esc to move to the previous window. In Main menu, click Esc to move to Exit menu.
24
Ch3. System information
„ Main menu
System Time
Current time. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these fields. To change the
value, press <+> or <−> key.
System Date
Today date. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these fields. To change the value,
press <+> or <−> key. Set any date from year 1981 to 2079. It will automatically keep track of leap years.
The system date can also be set from the operating system.
Product Name
This shows the name of PC.
Processor Type
This shows the type of CPU.
Processor Spd
This shows the speed CPU.
BIOS Version
This shows the Version of BIOS.
KBC Version
This shows the Version of KBD firm ware.
UUID
This is for display only. This shows the UUID.
Pri Master
Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Primary IDE Master
is HDD and its parameters.
Pri Slave
Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Primary IDE Slave
is HDD and its parameters.
Sec Master
Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Secondary IDE
Master is optical drive and its parameters.
Sec Slave
Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Secondary IDE
Slave is optical drive and its parameters.
System Memory
This is for display only. This shows size of system memory.
Ext. Memory
This is for display only. This shows size of extended memory.
25
Ch3. System information
„ Advanced menu
Legacy USB Support
There are two options to this field: Enabled, and Disabled. This field allows you to enable or disable the
legacy USB support.
Boot-time Diagnostic Screen
Enables the Boot-time Diagnostic Screen.
SATA Controller Mode
Set SATA (Serial ATA) Controller Mode.
AHCI Configuration
Enables the AHCI (Advanced Host Controller Interface).
Battery Charge Stop Percentage
Set Battery Charge Stop Percentage.
Fan Mode Control
Set Fan Mode Control.
Fn Key Setup
Set Sticky fn key function.
Wake On Lan
Enables Wake On Lan.
PXE/Remote Boot
Enables PXE/Remote Boot.
Execute-Disable Bit Capability
Enables Execute-Disable Bit Capability.
„ Security menu
Supervisor Password Is
This shows the system’s supervisor password has been set, or not.
Set Supervisor Password
Set Supervisor Password.
User Password Is
This shows the system’s User Password has been set, or not.
Set User Password
Set User Password.
Password on boot
Enables Password on boot.
HDD Password Is
This shows the system’s HDD Password has been set, or not.
Set HDD Password
Set HDD Password.
26
Ch3. System information
„ Boot menu
Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices Hard drive,
and Network boot as shown below.
CD-ROM Drive
Removable Devices
Hard Drive
B2 D0 Yukon PXE
„ Exit menu
Exit Saving Changes
Select Exit Saving Changes to save new setup information in CMOS RAM. CMOS RAM stores the
information using the backup battery; therefore, the information will not be lost when the computer is
turned off.
Exit Discarding Changes
Select Exit Discarding Changes to discard new setup information. If you made changes to items other
than date, time, and passwords, the Setup Warning asks you to save the new configurations. Select Yes
and press Enter to save the new configuration.
Load Setup Defaults
Select Load Setup Defaults to change the setup information to the factory default settings. If you select
Load Setup Defaults or press F9, Setup Confirmation asks you to confirm your selection. Press Yes to
load setup defaults.
Discard Changes
Discard change value.
Save Changes
Save change value.
27
Ch4. Symptom-to-part index
Chapter 4. Symptom-to-part index
The symptom-to-part index in this section lists symptoms and errors and their possible causes.
The most likely cause is listed first.
Note
If replacing a part (FRU) does not solve the problem, put the original part back in the computer.
Do not replace a non-defective FRU.
„ Power system checkout
· To verify a symptom, do the following :
1. Power off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Check that power is supplied when you power on the computer.
5. Power off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you power on the computer.
· If you suspect a power problem, see the appropriate one of the following power supply checkouts :
1. Checking the AC adapter
2. Checking the operational charging
3. Checking the battery pack
4. Checking the backup battery
· Checking the AC adapter
If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity
and installation.
If the computer does not charge during operation, go to “Checking operational charging.”
To check the AC adapter, do the following :
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the
2
1
AC adapter cable. See the following figure :
28
Pin
Voltage (V dc)
1
+18.05 ~ +19.95
2
Ground
Ch4. Symptom-to-part index
· If the voltage is not correct, replace the AC adapter.
· If the voltage is acceptable, do the following :
1. Replace the system board.
2. If the problem persists, check the AC adapter whether it is correct product or not.
Note
Noise from the AC adapter does not always indicate a defect.
· Checking operational charging
1. To check whether the battery charges properly during operation, use a discharged battery pack or a
battery pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
does not turn on, replace the battery pack.
2. If the charge indicator still does not turn on, replace the system board.
Then reinstall the battery pack.
Note
Do not charge battery pack, when its temperature is below 0
or above 75
.
· Checking the battery pack
1. Open the Power Meter window by clicking Start
Control Panel
Power Options and then;
check the total power remains. Battery charging does not start until the power Meter shows that less
than 95% of the total power remains; under this condition the battery pack can charge to 100% of its
capacity. This protects the battery pack from being overcharged or from having a shortened life.
2. To check the status of your batter, move your cursor to the Power Meter icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power
remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.
Note
If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and
Leave it at room temperature for a while. After it cools down, reinstall and recharge it.
29
Ch4. Symptom-to-part index
· The Characteristics of the battery pack
1. Self-discharge
The battery gradually loses its power over time without ever being used.
2. Periodic full discharge / charge
Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,
you can perform the full discharge / charge to improve the capacity. You should perform periodic full
discharge /charge once every 30~60 days.
You should always use the battery until its power is low; then fully charge the battery.
3. Trickle charge
If the temperature of the battery pack drops below 10
, the trickle charging begins.
The trickle charging may take 32 hours for the battery pack to be fully charged.
30
Ch4. Symptom-to-part index
· To check the battery pack, do the following :
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+).
See the following figure :
5(+)
4
3
2
Terminal
Voltage (V dc)
1
Ground(-)
5
+0V ~ +12.6V
(6 cell)
1(-)
3. If the voltage is still less than +11.1 V DC after recharging, replace the battery.
4. If the voltage is more than +11.1 V DC, measure the resistance between battery terminals 1 and 2.
The resistance must be 2 to 4
(typically 3
).
5. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system
board.
Note
Charging will take at least 3 hours.
Note
Battery is an expendable supplier, so its capacity and used time can be reduced by using the computer.
31
Ch4. Symptom-to-part index
„ Numeric error codes
Symptom / Error
FRU or action, in sequence
0200
Fixed disk failure
(The hard disk is not working)
1.Reset the hard-disk drive.
2.Load Setup Defaults in BIOS Setup Utility.
3.Hard-disk drive.
4.System board.
0210
Stuck Key error
1.Check the keyboard if it is pressed.
2.Replace the keyboard.
0211
Keyboard error
Run interactive tests of the keyboard and the auxiliary
input device.
0212
Keyboard Controller Failed
System board.
0220
Monitor type error - Monitor type does not
match the one specified in CMOS.
Load Setup Defaults in BIOS Setup Utility.
0230
System RAM error - System RAM Failed at
offset.
1.DIMM
2.System board
0231
Shadow RAM error - Shadow RAM failed at
offset
System board
0232
Extended RAM error - Extended RAM Failed
at address line
1. DIMM
2. System board
0250
System battery error – System battery is dead
Replace the backup battery and run BIOS Setup Utility
to reset the time and date.
32
Ch4. Symptom-to-part index
Symptom / Error
FRU or action, in sequence
0251
System CMOS checksum bad
– System CMOS checksum is not correct.
– Default configuration used.
Replace the backup battery and run BIOS Setup Utility
to reset the time and date.
0252
Password checksum bad – The password is
cleared.
Reset the password by running BIOS Setup Utility.
0260
System timer error
1. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
2. System board.
0271
Check date and time settings – Date and time
error.
Run BIOS Setup Utility to reset the time and date.
0280
Previous boot incomplete
- Default configuration used
1. Load “Setup Default” in BIOS Setup Utility.
2. DIMM.
3. System board.
0281: Memory Size found by POST differed
from EISA CMOS
Load Setup Defaults in BIOS Setup Utility.
02B0
Diskette drive A error
Set up the diskette type in BIOS Setup Utility.
02B1
Diskette drive B error
Set up the diskette type in BIOS Setup Utility.
02B2
Incorrect drive A type – Floppy diskette drive
error
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02B3
Incorrect Drive B type
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02D0
System cache error – Cache disabled
(RAM cache failed and BIOS disabled)
1. Load “Setup Default” in BIOS Setup Utility.
2. System board.
02F4
EISA CMOS not writable
1. Load “Setup Default” in BIOS Setup Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed
1. DIMM
2. System board
02F6
Software NMI failed
1. DIMM
2. System board
33
Ch4. Symptom-to-part index
Symptom / Error
FRU or action, in sequence
02F7
Fail – Safe timer NMI failed
1. DIMM
2. System board
0611
IDE configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0612
IDE configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0613
Com A configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0614
Com A configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0615
Com B configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0616
Com B configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0617
Floppy configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0618
Floppy configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
0619
Parallel port configuration changed
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
061A
Parallel port configuration error
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
34
Ch4. Symptom-to-part index
„ Error message
Symptom / Error
FRU or action, in sequence
Device address conflict.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid System Configuration Data.
1. DIMM.
2. System board.
I/O Device IRQ Conflict.
1. Load Setup Defaults in BIOS Setup Utility.
2. Backup battery.
3. System board.
Operating System not found.
1. Check that the operating system has no failure and
is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard
-disk drive and the diskette drive are properly
identified.
3. Reset the hard-disk drive.
4. Reinstall the operating system.
5. Diskette drive.
6. Hard-disk drive.
7. System board.
Hibernation error.
1. Restore the system configuration to what it was
before the computer entered hibernation mode.
2. If memory size has been changed, re-create the
hibernation file.
FAN error.
Fan.
Thermal sensing error.
System board.
35
Ch4. Symptom-to-part index
„ LCD-related symptoms
Note
Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack also.
Symptom / Error
FRU or action, in sequence
LCD screen becomes dark suddenly.
Check out Battery Miser.
Nothing displayed on LCD screen.
1. Check out Battery Miser.
2. Choose Never in the Turn off Monitor item on
Power Options Properties.
3. Check the power save mode switch if it is pressed
by something.
4. Check the System is in standby or hibernation
mode.
LCD backlight not working.
LCD too dark.
LCD brightness cannot be adjusted.
1. Reconnect inverter to the board connector.
2. Replace inverter.
3. LCD assembly.
4. System board.
LCD color cannot be adjusted.
LCD screen abnormal.
Characters missing pixels.
LCD screen unreadable.
Wrong color displayed.
1. Reset all LCD connectors.
2. Replace LCD cable.
3. LCD assembly.
4. System board.
Horizontal or vertical lines displayed
on LCD
LCD assembly.
Power-on indicator on, and a blank\LCD
during POST.
LCD assembly.
System board.
36
Ch4. Symptom-to-part index
„ Indeterminate problems
· You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices
are installed, a short circuit is suspected, or the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
· Verify that all attached devices are supported by the computer.
· Verify that the power supply being used at the time of the failure is operating correctly.
1. Power off the computer
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnected all of the following devices :
a. Non-LG devices.
b. Printer, mouse, and other external devices.
c. Battery pack.
d. PC cards.
e. ODD (CD-ROM, Combo) drive or FDD drive in the Bay.
f. Hard-disk drive.
Note
Use the other memory card because it needs when operating computer.
4. Power on the computer.
5. Determine whether the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time.
(do not replace a non-defective FRU)
a. LCD assembly (Check external monitor whether the same problem recurs or not).
b. Keyboard.
c. Keydeck (TouchPad and Scroll Button assembly).
d. System board.
37
Ch5. Removing and replacing a part
Chapter 5. Removing and replacing a part (FRU)
Danger
Before removing any FRU, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
Caution
Before the computer is powered on after FRU replacement, make sure that all screws, springs,
and other small parts are in place and are not loose inside the computer. Verify metal flakes can
cause electrical short circuits.
Note
As for the screw, every Torque 3
0.2Kgfcm(0.196Nm)
38
Ch5. Removing and replacing a part
■ Battery Pack
1. Push the battery latch in the direction shown below; then side the battery pack out of the slot.
39
Ch5. Removing and replacing a part
■ Hard Disk Drive
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove two screws as indicated in the picture.
40
Ch5. Removing and replacing a part
2. Then pull the HDD assembly out in the direction shown below.
41
Ch5. Removing and replacing a part
■ Keyboard
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove 2 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 x L6.5
2
42
Ch5. Removing and replacing a part
2. To remove 4 hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard,
and pull it up.
3. Remove keyboard and disconnect Keyboard cable.
43
Ch5. Removing and replacing a part
■ BMDC(MDC) Modem Card
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove 2 MDC Board Screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4023A
M2.0 X L3.5
2
2. Remove MDC card and disconnect cable.
44
Ch5. Removing and replacing a part
■ Optical Disk Drive
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Keyboard 3. BMDC(MDC) Modem Card
1. Remove 2 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4019F
M2.0 X L4.5
2
2. Remove a screw, insert a screwdriver into the hole located at the rear of ODD and push it out.
45
Ch5. Removing and replacing a part
■ Keyboard Deck
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive
1. Remove 17 screws.
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
14
2
1SZZBA4017A
M2.0 X L3.0
3
2. Remove 3 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
3
46
Ch5. Removing and replacing a part
3. Disconnect cable.
4. Disassemble the KBD Deck Assy.
47
Ch5. Removing and replacing a part
■ Fan Assembly
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Remove 8 screws and then remove FAN Assembly.
2
2
2
1
2
2
1
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4022A
M2.0 X L12.0
3
2
1SZZBA4023A
M2.0 X L3.5
5
2. Disconnect connector and pull it up.
48
Ch5. Removing and replacing a part
■ Wireless LAN Card
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove Cover Mini PCI screws.
2. Disconnect WLAN antenna cable and remove WLAN card.
49
Ch5. Removing and replacing a part
■ Display Module
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Mini PCI Cover Antenna 4. Keyboard 5. Keyboard Deck
1. Remove Wireless cable from hole.
Remove LCD connector. You will see a tag designed to make the work easier. Pull out the tag.
2. Remove 2 Hinge cover screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4023A
M2 X L3.5
2
3. Remove cap hinge small. (Applied both left and right side.)
50
Ch5. Removing and replacing a part
4. Disconnect LCD connector and Modem connector.
Remove WLAN antenna.
51
Ch5. Removing and replacing a part
5. Remove 2 Hinge Screws and remove Hinge.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
2
6. Remove screw cover and remove 2 Hinge screws. (Applied both left and right side.)
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
4
52
Ch5. Removing and replacing a part
53
Ch5. Removing and replacing a part
■ Speaker
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Disconnect MIC cable.
2. Remove Speaker from Guide Boss.
54
Ch5. Removing and replacing a part
3. Disconnect connector and remove Speaker.
55
Ch5. Removing and replacing a part
■ Sub Board
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive
6. Display Module
1. Remove 4 screws and remove Sub B/D.
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 x L6.0
4
2. Remove 2 screws and remove Audio Sub B/D.
No.
FRU No.
Specification
Qty
1
1SZZBA4019F
M2 x L4.5
3
56
Ch5. Removing and replacing a part
■ Main Board
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive
6. Fan Assembly 7. Speaker 8. Sub Board
1. Remove Cover Block HDD.
2. Remove 5 Main Board screws and remove 2 Frame Hinge Left screws.
1
1
2
2
2
2
2
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 X L6.0
2
2
1SZZBA4023A
M2 X L3.5
5
57
Ch5. Removing and replacing a part
3. Remove Main Board.
58
Ch5. Removing and replacing a part
■ Display Module Exploded View
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Using a knife, remove the logo and rubbers that are covering the screws.
Then remove all 8 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 X L6.0
8
59
Ch5. Removing and replacing a part
2. Remove LCD Hook.
60
Ch5. Removing and replacing a part
3. Remove 2 screws and remove tape.
No.
FRU No.
Specification
Qty
1
1SZZBA4080F
M2.5 x L4.5
2
61
Ch5. Removing and replacing a part
4. Remove LCD power cable and remove Inverter.
5. (Left, Right) Remove 4 Hinge screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4080F
M2.5 x L4.5
4
62
Ch5. Removing and replacing a part
6. Remove LCD panel.
63
Ch5. Removing and replacing a part
7. Remove 8 Hinge Assembly screws. Remove LCD Cable Tape.
No.
FRU No.
Specification
Qty
1
1SZZBA4017A
M2 x L3.0
8
64
Ch5. Removing and replacing a part
65
Ch5. Removing and replacing a part
8. Remove WLAN Antenna.
66
Ch5. Removing and replacing a part
■ Battery Pack
1. Push the battery latch in the direction shown below; then side the battery pack out of the slot.
67
Ch5. Removing and replacing a part
■ Hard Disk Drive
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove two screws as indicated in the picture.
68
Ch5. Removing and replacing a part
2. Then pull the HDD assembly out in the direction shown below.
69
Ch5. Removing and replacing a part
■ Keyboard
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove 2 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 x L6.5
2
70
Ch5. Removing and replacing a part
2. To remove 4 hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard,
and pull it up.
3. Remove keyboard and disconnect Keyboard cable.
71
Ch5. Removing and replacing a part
■ Optical Disk Drive
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Keyboard
1. Remove 2 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4019F
M2.0 X L4.5
2
2. Remove a screw, insert a screwdriver into the hole located at the rear of ODD and push it out.
72
Ch5. Removing and replacing a part
■ Wireless LAN Card
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove Cover Mini PCI screws.
2. Disconnect WLAN antenna cable and remove WLAN card.
73
Ch5. Removing and replacing a part
■ BMDC(MDC) Modem Card
Remove the following parts in order before replacing this part.
1. Battery Pack
1. Remove 2 MDC Board Screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4023A
M2.0 X L3.5
2
2. Remove MDC card and disconnect cable.
74
Ch5. Removing and replacing a part
■ Keyboard Deck
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive
1. Remove 17 screws.
2
2
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
13
2
1SZZBA4017A
M2.0 X L3.0
4
2. Remove 7 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
7
75
Ch5. Removing and replacing a part
3. Disconnect cable.
4. Disassemble the KBD Deck Assy.
76
Ch5. Removing and replacing a part
■ Fan Assembly
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Remove 8 screws and then remove FAN Assembly.
2
2
1
2
1
2
2
1
No.
FRU No.
Specification
Qty
1
1SZZBZ4022A
M2.0 X L12.0
3
2
1SZZBA4023A
M2.0 X L3.5
5
2. Disconnect connector and pull it up.
77
Ch5. Removing and replacing a part
■ Display Module
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Mini PCI Cover Antenna 4. Keyboard 5. Keyboard Deck
1. Remove Wireless cable from hole.
Remove LCD connector. You will see a tag designed to make the work easier. Pull out the tag.
2. Remove 2 Hinge cover screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4023A
M2 X L3.5
2
3. Remove cap hinge small. (Applied both left and right side.)
78
Ch5. Removing and replacing a part
4. Disconnect LCD connector and Modem connector.
Remove WLAN antenna.
79
Ch5. Removing and replacing a part
5. Remove 2 Hinge Screws and remove Hinge.
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
2
6. Remove screw cover and remove 2 Hinge screws. (Applied both left and right side.)
No.
FRU No.
Specification
Qty
1
1SZZBA4097A
M2.5 X L6.5
4
80
Ch5. Removing and replacing a part
81
Ch5. Removing and replacing a part
■ Speaker
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Disconnect MIC cable.
2. Remove Speaker from Guide Boss.
82
Ch5. Removing and replacing a part
3. Disconnect connector and remove Speaker.
83
Ch5. Removing and replacing a part
■ Sub Board
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive
6. Display Module
1. Remove 4 screws and remove Sub B/D.
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 x L6.0
4
2. Remove 2 screws and remove Audio Sub B/D.
No.
FRU No.
Specification
Qty
1
1SZZBA4019F
M2 x L4.5
3
84
Ch5. Removing and replacing a part
■ Woofer
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive
6. Fan Assembly 7. Speaker
1. Remove Audio Sub Board.
Remove 3 Screws.
No.
FRU No.
Specification
Qty
1
1SZZBZ4023A
M2.5xL11, D7(3.5)
3
85
Ch5. Removing and replacing a part
2. Disconnect connector and remove Woofer.
86
Ch5. Removing and replacing a part
■ Main Board
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck 5. Optical Disk Drive
6. Fan Assembly 7. Speaker 8. Woofer 9. Sub Board
1. Remove Cover Block HDD.
87
Ch5. Removing and replacing a part
2. Remove 6 Main Board screws. Remove 2 ODD interface Board screws.
Remove Main board and ODD board.
3
3
2
2
2
2
2
1
1
2
2
2
No.
FRU No.
Specification
Qty
1
1SZZBZ4002B
M2.0 X L2.7
2
2
1SZZBA4023A
M2.0 X L3.5
8
3
1SZZBA4080G
M2.0 X L6.0
2
88
Ch5. Removing and replacing a part
■ Display Module Exploded View
Remove the following parts in order before replacing this part.
1. Battery Pack 2. Hard Disk Drive 3. Keyboard 4. Keyboard Deck
1. Using a knife, remove the logo and rubbers that are covering the screws.
Then remove all 8 screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 X L6.0
8
89
Ch5. Removing and replacing a part
2. Remove LCD Hook.
90
Ch5. Removing and replacing a part
3. Remove 2 screws and remove tape.
No.
FRU No.
Specification
Qty
1
1SZZBA4017A
M2.0 X L3.0
2
91
Ch5. Removing and replacing a part
4. Remove LCD power cable and remove Inverter.
5. (Left, Right) Remove 4 Hinge screws.
No.
FRU No.
Specification
Qty
1
1SZZBA4080G
M2.5 X L6.0
4
92
Ch5. Removing and replacing a part
6. Remove LCD panel.
93
Ch5. Removing and replacing a part
7. Remove 8 Hinge Assembly screws. Remove LCD Cable Tape.
No.
FRU No.
Specification
Qty
1
1SZZBA4017A
M2.0 X L3.0
8
94
Ch5. Removing and replacing a part
95
Ch5. Removing and replacing a part
8. Remove WLAN Antenna.
96
Ch6. Part lists
Chapter 6. Part lists
2005-01-31
Specification
HTW09
Location
Part Number
Remarks
HWL01
6304FLP155A
LP154W01-A3 LG PHILPS TFT COLOR 15.4 INCH WXGA(1280X800) 185NITS NON
GLARE
LCD단품
HWL01
6304FLP155B
LP154W01-A3K3 LG PHILPS TFT COLOR 15.4 INCH WXGA(1280X800) 185NITS
GLARE
LCD단품
HWL02
3111B97116A
15.4" Case A'y, Front with Tape 154W
LCD Front
case
HWL03
3111B09831A
15.4" Case A'y, Rear 154W
LCD Rear
case
HWL04
6851B34024A
15.4" LCD cable SXGA(Taeyang)
LCD Cable
HWL04
6851B34024B
15.4" LCD cable XGA(Taeyang)
LCD Cable
HWL04
6851B34034A
15.4" LCD cable SXGA(Wanshih)
LCD Cable
HWL04
6851B34034B
15.4" LCD cable XGA(Wanshih)
LCD Cable
HWL05
4774BD2002A
15.4" Hinge,Left BKT154W
HWL06
4774BD2001A
15.4" Hinge,Right with BKT 154W
HWL07
4850BA4009A
15.4" Cushion LCD Rear Left
Cushion rear
left
HWL08
4850BA4010A
15.4" Cushion LCD Rear Right
Cushion rear
right
HWL09
4850BA4011A
15.4" Cushion, wide LCD mid R
Cushion LCD
mid right
HWL10
4850BA4012A
15.4" Cushion, wide LCD mid L
Cushion LCD
mid left
HWL11
4850BA4013A
15.4" Cushion, wide LCD top R
Cushion LCD
top right
HWL12
4850BA4014A
15.4" Cushion, wide LCD top L
Cushion LCD
top left
HWL13
4940BM4165A
15.4" Knob, LCD Latch
Knob
HWL14
4026BM3017A
15.4" Latch, display 154W
Latch
HWL15
4970BW4559A
15.4" Spring, Latch
Spring
HWL16
6304FLP166B
LP171WX2-A4K1 LG PHILPS TFT COLOR WXGA+ 1440X900 LVDS 200NITS GLARE
LCD단품
HWL16
6304FLP165A
LP171W02-A4 LG PHILPS TFT COLOR WSXGA+ 1680X1050 LVDS 170NITS GLARE
LCD단품
HWL17
3111B97115A
17.1" Case Assy Front with Tape
LCD plate left
LCD plate
right
LCD Front
case
97
Ch6. Part lists
Location
Part Number
Specification
Remarks
HWL18
3111B97117A
17.1" (rear case, anternna cover, spring, knob l/r)
LCD Rear
case assy
HWL19
6851B34025A
17.1" LCD cable 17.1" SXGA(Taeyang)
LCD Cable
HWL19
6851B34035A
17.1" LCD cable 17.1" SXGA(Whashih)
LCD Cable
HWL20
4774BD2003A
17.1" Hinge,Left with BKT 171W
HWL21
4774BD2004A
17.1" Hinge,Right BKT171W
HWL22
4850BP4043A
17.1" Cushion, rubber supporter LCD Upper
Cushion rear
upper
HWL23
4850BP4047A
17.1" Cushion, rubber supporter LCD Lower
Cushion rear
lower
HWL24
4850BP4052A
17.1" Cushion, rubber supporter LCD side
Cushion rear
side
HWL25
4850BP4042A
17.1" Cushion, rubber cover screw
cover screw
top
HWL26
3858BP4260A
17.1" Sheet, Cover screw mid
cover screw
bottom mid
HWL27
5016BZ9100B
15.4" / 17.1" Magnetic, LID(H5mm)
Magnetic
HWL28
3858BZ4100A
15.4" / 17.1" Sheet, Cover Magnetic
Magnetic
cover
HWL29
5011B00017A
15.4" / 17.1" W/L Antenna LEFT
HWL30
5011B00018A
15.4" / 17.1" W/L Antenna RIGHT
HWL31
3940BP4011A
15.4" / 17.1" cushion antenna
HWL32
3858BZ4466A
15.4" / 17.1" Sheet, Cover screw(silver)
cover screw
(154top, 171
bottom side)
HWL33
6708BI0089A
DAC-08B073 DELTA GENERAL GENERAL GENERAL HUNTER-TL 15 INCH
HUNTER-FULL ALL, HUNTER-TL ALL, OZ1060S
LCD Inverter
HWL33
6708BI0088B
KUBNKM095A ALPS GENERAL GENERAL GENERAL HUNTER-FULL 15 INCH
HUNTER-FULL ALL, HUNTER-TL ALL, MP1017
LCD Inverter
HWL34
3858BP4273A
N HUNTER-TL 14.1 INCH BADGE "X-NOTE"
Logo badge
HWL34
3858BZ4462A
N HUNTER-TL 14.1 INCH BADGE "LG"
Logo badge
HWB01
6871BWG11AA
HUNTER-W MAIN B/D ASSY LGE 10 LAYERS REV 0.9 GM 15.4 PP
M/B Assy
HWB01
6871BWP11AA
HUNTER-W MAIN B/D ASSY LGE 10 LAYERS REV 0.9 PM ATI 64M 15.4 PP
M/B Assy
LCD plate left
LCD plate
right
Antenna left
Antenna right
Antenna
cushion
98
Ch6. Part lists
Location
Part Number
Specification
HWB01
6871BW711AA
HUNTER-W MAIN B/D ASSY LGE 10 LAYERS REV 0.9 PM ATI 64M 17.1 PP
M/B Assy
HWB01
6871BWP21AA
HUNTER-W MAIN B/D ASSY LGE 10 LAYERS REV 0.9 PM ATI 128M 15.4 PP
M/B Assy
HWB01
6871BW721AA
HUNTER-W MAIN B/D ASSY LGE 10 LAYERS REV 0.9 PM ATI 128M 17.1 PP
M/B Assy
NMEM1
0IMMRIH046A
HYS64T32000HDL-5-A INFINEON 200P SODIMM BK 256MB 32MX64 400MHZ DDR2
SDRAM WITH 32MX16
Memory
NMEM1
0IMMRHY061A
HYMP532S646-E3 HYNIX 200P SODIMM BK 256MB 32MX64 400MHZ DDR2 SDRAM
WITH 32MX16
Memory
NMEM1
0IMMRSS113A
M470T3354BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 256MB 32MX64
400MHZ DDR2 SDRAM WITH 32MX16
Memory
NMEM1
0IMMRIH047A
HYS64T64020HDL-5-A INFINEON 200P SODIMM BK 512MB 64MX64 400MHZ DDR2
SDRAM WITH 32MX16
Memory
NMEM1
0IMMRHY062A
HYMP564S646-E3 HYNIX 200P SODIMM BK 512MB 64MX64 400MHZ DDR2 SDRAM
WITH 32MX16
Memory
NMEM1
0IMMRSS114A
M470T6554BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 512MB 64MX64
400MHZ DDR2 SDRAM WITH 32MX16
Memory
NMEM1
GIMMR00007A
HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ
DDR2 SDRAM WITH 32MX16
Memory
NMEM1
0IMMR00005A
M470T3354BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 256MB 32MX64
533MHZ DDR2 SDRAM WITH 32MX16
Memory
NMEM1
0IMMR00008A
HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ
DDR2 SDRAM WITH 32MX16
Memory
NMEM1
GIMMR00008A
HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ
DDR2 SDRAM WITH 32MX16
Memory
NMEM1
0IMMR00006A
M470T6554BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 512MB 64MX64
533MHZ DDR2 SDRAM WITH 32MX16
Memory
HTA04
2020B00030A
GCC-4243N HLDS 8X 24X 24X 24X 12.7MM W/COMMON BEZEL FOR BRAND
ODD 단품
HTA04
2026B00007A
GSA-4080N HLDS 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK 12.7MM
COMMON TYPE FOR BRAND
ODD 단품
HTA04
2090B20001A
DV-28E-C88 TEAC 8X 24X NOTE BOOK 12.7MM W-COMMON BEZEL FOR BRAND
NB-PC
ODD 단품
HTA04
2020B00033A
DW-224E-B88 TEAC 8X 24X 24X 24X 12.7MM W-COMMON BEZEL FOR BRAND NBPC
ODD 단품
HTA04
2026B00009A
DV-W28E-588 TEAC 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK 12.7MM
W/COMMON BEZEL FOR BRAN NB-PC
ODD 단품
99
Remarks
Ch6. Part lists
Location
Part Number
Specification
HTA05
3300BP4459A
PLATE, ODD SUPPORT HUNTER 15.4 WIDE .
HTA06
1SZZBA4041A
+ D3.5 L3.0MM SWRH4 DUMMY COVER FIX SILVER MAGELLAN DISPLAY
HTA03
6744C00085A
MHT2040AT PL FUJITSU 40GB EIDE INNER ZEBRA/MACKINLEY/K2
HDD 단품
HTA03
6744C00122A
HTS424040M9AT00 HGST 40GB EIDE INNER MCKINLY 4200RPM
HDD 단품
HTA03
6744C00086A
MHT2060AT PL FUJITSU 60GB EIDE INNER ZEBRA/MCKINLEY/K2
HDD 단품
HTA03
6744C00106A
IC25N060ATMR04-0 HGST 60GB EIDE INNER MCKINLEY/K2 4200RPM
HDD 단품
HTA03
6744C00087A
MHT2080AT PL FUJITSU 80GB EIDE INNER ZEBRA/MCKINLEY/K2
HDD 단품
HTA03
6744C00107A
IC25N080ATMR04-0 HGST 80GB EIDE INNER MCKINLEY/K2 4200RPM
HDD 단품
HTA03
6744C00123A
MHV2100AT FUJITSU 100GB EIDE INNER HUNTER-S 4200RPM
HDD 단품
HTA01
4811B00605A
HUNTER-WIDE 15.4 INCH HDD SUS 17.1W, 15F
HDD PLATE
ASSY
HTA02
1SZZBA4011A
+ D3.0 L 3.0 SWRH4 HDD WH [S-PJT] #1 TIP
HDD SCREW
HWC04
6871BZT14AC
WM3B2200BGMW2 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG LAN MINIPCI TYPE CH 1-11 NETWORK CONNECTIO
Wireless LAN
b/g
HWC04
6871BZT14AD
WM3B2200BGRW3 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG LAN MINIPCI TYPE CH 1-14 NETWORK CONNECTIO
Wireless LAN
b/g
HWC04
6871BZT14AE
WM3B2915ABGNA INTEL 4 LAYERS REV 2.0 CH 1-11 NETWORK CONNECTION
MINIPCI TYPE IIIB STANDARD
Wireless LAN
a/b/g
HWC04
6871BZT14AF
WM3B2915ABGEU INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK CONNECTION
MINIPCI TYPE IIIB STANDARD
Wireless LAN
a/b/g
HWC04
6871BZT14AG
WM3B2915ABGRW INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK CONNECTION
MINIPCI TYPE IIIB STANDARD
Wireless LAN
a/b/g
HTC05
6871BG867ZB
T60M893T00 FOXCONN 2 LAYERS REV 0.0 MDC1.5 FORM FACTOR INTERNAL
56K MDC MODEM
MDC Assy
HTC05
6871BG869ZB
MA560-3 QCOM 2 LAYERS 1A MDC1.5 FORM FACTOR V.92 MODEM CARD
MDC Assy
HTA07
6911B00092A
4800MAH 3S-2P LGC LI-ION CYLINDERICAL HUNTER-ALL CELL LGC
Battery
HTA07
6911B00119A
4800 mAh 3S-2P Simplo Li-Ion Cylindrical Hunter All SDI cell
Battery
HTA07
6911B00121A
4800 mAh 3S-2P Simplo Li-Ion Cylindrical Hunter All LGC cell
Battery
HWC07
5901B09279A
15.4" /17.1" Thermal Module A'y with Gasket
HWC08
0IMCR00011A
RH80536GE0252M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 730
1.60GHZ/600MHZ C0-STEPPING(SL86G)
100
Remarks
ODD
SUPPORT
PLATE
PLATE
SCREW
FAN Assy
CPU
Ch6. Part lists
Location
Part Number
Specification
HWC08
0IMCR00009A
RH80536GE0302M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 740
1.73GHZ/600MHZ C0-STEPPING(SL7SA)
CPU
HWC08
0IMCR00007A
RH80536GE0362M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 750
1.86GHZ/600MHZ C0-STEPPING(SL7S9)
CPU
HWC08
0IMCR00005A
RH80536GE0412M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 760
2.00GHZ/600MHZ C0-STEPPING(SL7SM)
CPU
HWC08
0IMCR00003A
RH80536GE0462M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 770
2.13GHZ/600MHZ C0-STEPPING(SL7SL)
CPU
HWC09
3823B01080A
15.4" /17.1" HUNTER-W LG-IBM CHICONY KOREA HUNTER W 99KEY PM
KBD
HWC09
3823B01080B
15.4" /17.1" HUNTER-W LG-IBM CHICONY KOREA HUNTER W 99KEY GM
KBD
HWC09
3823B01081A
15.4" /17.1" HUNTER-W LG-IBM CHICONY ENGLISH HUNTER W 99KEY PM
KBD
HWC09
3823B01081B
15.4" /17.1" HUNTER-W LG-IBM CHICONY ENGLISH HUNTER W 99KEY GM
KBD
HWC11
6708BA0056A
PA-1900-08LK LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL FOR KOREA
Adapter
HWC11
6708BA0057A
HP-AP091F13P1 HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR KOREA,
SLIM TYPE.
Adapter
HWC11
6708BA0056B
PA-1900-08LG LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR
EXPORT, SLIM TYPE
Adapter
HWC11
6708BA0057B
HP-AP091F13P HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR
EXPORT, SLIM TYPE.
Adapter
HWC12
6910BLC3201
CR2032 SONY 3V 220MA/H COIN
RTC
HWC12
6910C00005A
CR2032 SONY 3.0 VOLT 200MA D2.0MM H3.2MM
RTC
HWC13
6410BM21002
PT8XXK9KB0A-033 LONGWELL KS 1000MM 3P CONN W/VELCRO TIE BLACK
Powercode
HWC13
6410BM21601
SP-022+IS-034 H05VV-F I-SHENG KS 1000MM 3P CONN W/VELCRO TIE BLACK
Powercode
HWC13
6410BX21602
PF8B1CIJ10A-060 LONGWELL GOST 1830MM 3PIN CONN. BLACK
Powercode
HWC13
6410BX21601
SP-022+IS-034+H05VV-F3G I-SHENG GOST 1800MM 3P CONN. BLACK
Powercode
HWC13
6410BK21005
PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BK21007
SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK
Powercode
HWC13
6410BK21006
AU10S3+H03VV-F+VAC5S VOLEX SAA 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BD21003
PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK
Powercode
HWC13
6410BV21002
PF8B1L1J10A-060 LONGWELL SII 1830MM 3PIN CONN. BLACK
Powercode
HWC13
6410BV21003
SP-86+IS-034 I-SHENG SII 1830MM 3PIN CONN. BLACK
Powercode
HWC13
6410BV21602
SI16S3+H03VV-F+VAC5S VOLEX SII 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BQ21003
SP-305+H05VV-F+IS-034 I-SHENG INMETRO 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BQ21002
BR10S3+H03VV-F+VAC5S VOLEX INMETRO 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BO20603
P48F1SAJ30A-060 LONGWELL CCC 1830MM 3P CONN BLACK
Powercode
101
Remarks
Ch6. Part lists
Location
Part Number
Specification
HWC13
6410BO20602
SP-506+RVV 3CX0.75MM2+IS-034 I-SHENG CCC 1830MM 3P CONN BLACK
Powercode
HWC13
6410BO21008
GB10S3+RW300_300+VAC5S VOLEX CCC 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BU21602
SP-80A+H05VV-F+IS-034 I-SHENG SABS 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BU21603
SA16A+H03VV-F+VAC5S VOLEX SABS 1830MM 3PIN CONN BLACK
Powercode
HWC13
6410BW21001
X-LGPC0415-001 VOLEX ISI 1830MM 3PIN CONN. BLACK
Powercode
HWC14
6401B02537A
15.4" Speaker Estec
SPEAKER
ASSY
HWC15
6401B02541A
17.1" Speaker Estec
SPEAKER
ASSY
HWC16
6400WESX06A
17.1" Woofer Assy with cushion Rubber woofer
WOOFER
ASSY
HWC17
6513B00006A
SKB-2744T-C1033 SEO KWANG-WIM TEK 2V 500MA 1KHZ -44DB 230MM AWG 28
BK WH FOR HUNTER-WIDE 15.4 / 17.1
MIC ASSY
HWC17
6513B00008A
OB-27L BO SUNG-WIM TEK 2V 500MA 1KHZ -44DB HUNTER-WIDE
MIC ASSY
HWC18
6710B00009A
RC-501 HTC LG LOGO FOR HUNTER-W W/O BATTERY
REMOCON
ASSY
HWC20
3301B00549A
10036875-AB00RRS HUNTER-F/W FCI COMBO EXPRESS CARD SLOT
HWS01
6871BWS01PC
HUNTER-W WIMTEC 4 LAYERS REV 0.5 FRONT AUDIO FFC SUB B/D MAIN ASSY
HWS02
6871BWS02PB
HUNTER-W WIMTEC 4 LAYERS REV 0.4 REAR S-VIDEO SUB B/D MAIN ASSY
Sub BD S
video
HWS03
6871BWS06PA
HUNTER-W WIMTEC 2 LAYERS REV 0.1 ODD SUB B/D MAIN ASSY FOR 17.1
Sub BD ODD
I/F
HWD01
3111B09801A
HUNTER-WIDE 15.4 INCH KBD DECK WITH REMOTE-CON.
KBD DECK
ASSY 15.4"
HWD01
3111B09801B
HUNTER-WIDE 15.4 INCH KBD DECK WITHOUT REMOTE-CON.
KBD DECK
ASSY 15.4"
HWD01
3111B09803A
HUNTER-WIDE 15.4 INCH KBD DECK PM MODEL EXPORT
KBD DECK
ASSY 15.4"
HWD01
3111B09803B
HUNTER-WIDE 15.4 INCH KBD DECK GM MODEL EXPORT
KBD DECK
ASSY 15.4"
HWD01
3111B09701A
HUNTER-WIDE 17.1 INCH KBD DECK .
KBD DECK
ASSY 17.1"
102
Remarks
PCMCIA
SOCKET
Sub BD
Audio
Ch6. Part lists
Location
Part Number
Specification
HWD01
3111B09701B
HUNTER-WIDE 17.1 INCH KBD DECK FOR EXPORT
HWD02
5022BZ9023A
TOUCH PWB 79.7*47.7 HUNTER WIDE WITH SCROLL FUNCTION SYNAPTICS
TM41PUZ307-1
Sub BD Tpad
HWD03
6871BWS04PA
HUNTER-W WIMTEC 2 LAYERS REV 0.6 TOUCH PAD SUB B/D MAIN ASSY W/ IR
FOR 15.4 PM
Sub BD Tpad button
15.4"
HWD03
6871BWS05PA
UNTER-W WIMTEC 2 LAYERS REV 0.6 TOUCH PAD SUB B/D MAIN ASSY W/O IR
FOR 15.4 GM
Sub BD Tpad button
15.4"
HWD04
6871BWS07PA
HUNTER-W WIMTEC 2 LAYERS REV 0.1 TOUCH PAD SUB B/D MAIN ASSY W/ IR
17.1 PM
Sub BD Tpad button
17.1"
HWD04
6871BWS03PB
HUNTER-W WIMTEC 2 LAYERS REV 0.4 POWER-BUTTON SUB B/D MAIN ASSY
Sub BD
power button
HWM01
3111B09811A
15.4" Case A'y, Bottom 154W with Remote con. (only PM)
BOTTOM
ASSY
HWM01
3111B09811B
15.4" Case A'y, Bottom 154W without Remote con. (only GM)
BOTTOM
ASSY
HWM01
3111B09711A
17.1" Case A'y, Bottom 171W
BOTTOM
ASSY
HWM02
3210BD2018A
HUNTER-WIDE 15.4 / 17.1 INCH ZN HINGE FRAME RIGHT
HWM03
3550BM3202A
HUNTER-WIDE 15.4 / 17.1 INCH PCABS HDD BLOCK
HWM04
3550BM3207A
HUNTER-WIDE 15.4 / 17.1 INCH PCABS CARDBUS DUMMY EXPRESS
EXPRESS
CARD
DUMMY
HWM05
3550BM3208A
HUNTER-WIDE 15.4 / 17.1 INCH PCABS CARDBUS DUMMY
CARDBUS
DUMMY
HWM06
3550BM3210A
HUNTER-WIDE 15.4 / 17.1 INCH RUBBER DUMMY DOCKING
RUBBER
DOCKING
DUMMY
HWM07
3550BM4047D
ME 14 PCABS DUMMY SD MEMORYCARD 15.4 / 17.1
HWM08
3551B00400A
HUNTER-WIDE 15.4 / 17.1 INCH MEMORY .
HWM09
3551B00500A
HUNTER-WIDE 15.4 / 17.1 INCH HDD .
HDD COVER
HWM10
5006BM3028A
CAP,HINGE RIGHT HUNTER 15.4 WIDE PCABS
HINGE CAP
RIGHT
103
Remarks
KBD DECK
ASSY 17.1"
HINGE
FRAME
RIGHT
HDD BLOCK
SD DUMMY
MEMORY
COVER
Ch6. Part lists
Location
Part Number
Specification
HWM11
5006BM3029A
CAP,HINGE LIGHT HUNTER 15.4 / 17.1 WIDE PCABS
HINGE CAP
LEFT
HWM12
5006BM3030A
CAP, HINGE RIGHT HUNTER 17.1 WIDE PCABS
HINGE CAP
RIGHT
HWM13
6850B11002A
UL20696 11P AWM 80C VW-1 200MM KFC HUNTER-W154
AUDIO
CABLE 11P
HWM14
6850B19001A
UL20696 19P AWM 80C VW-1 125MM 0.5MM KFC H154W(S-VIDEO BOARD)
HWM15
6850B22003A
UL20696 22P AWM 80C VW-1 100MM KFC HUNTER-W154
HWM16
6851B09239A
17.1" Cable Ass'y, Audio board H171W
HWM17
6850B19002A
UL20696 19PIN AWM 80C VW-1 175MM 0.5MM KFC H171W(S-VIDEO BOARD)
HWM18
3858BZ4472A
N N N N HUNTER-WIDE 15.4 INCH COVER SCREW FOR FRAME
COVER
SCREW I/O
PORT
HTM05
6851B76020C
HUNTER-T N MDC INTERFACE WIM TEK 210MM 2P HUNTER-TL
MDC CABLE
HWM20
1SZZBA4080F
15.4" Screw M2.5xL4.5(Silver)
SCREW A
HWM21
1SZZBZ4002B
17.1" M2xL2.7, D5.5 H0.8, ODD I/F
SCREW B
HWM22
1SZZBZ4023A
17.1" M2.5xL11, D7(3.5) , Special Woofer
SCREW C
HWM23
1SZZBA4097A
15.4" /17.1"Screw M2.5xL6.5 (BK)
SCREW D
HWM24
1SZZBA4080G
15.4" /17.1"Screw M2.5xL6.0(Yellow)
SCREW E
HWM25
1SZZBZ4022A
15.4" /17.1"Screw, M2.0xL.12 Silver
SCREW F
HWM26
1SZZBA4023A
15.4" /17.1"Screw,M2xL3.5 Silver
SCREW G
HWM27
1SZZBA4017A
15.4" /17.1"Screw M2xL3 BK
SCREW H
HWM28
1SZZBA4019F
15.4" /17.1"Screw M2.0xL4.5 Yellow
SCREW I
HWM29
3850BB9110A
INTEL GRYPHON BANIAS LOGO 252352-001 INTEL CENTRINO LABEL N N
INTEL
LABEL
HWM29
3850BB9110C
CENTRINO LABEL NT 252352-002 INTEL
INTEL
LABEL
HWM30
3850BZ9A15A
MS WIN XP U2 BEZEL 15.4 / 17.1
MS LABEL
HWM30
3850BB4125A
MS WIN XP U2 BEZEL 15.4 / 17.1
MS LABEL
HWM31
3850BZ9A87A
ATI Label, X600
ATI LABEL
HWM33
3850BF9045A
POP LABEL LW60 GM FOR DOMESTIC
POP LABEL
HWM33
3850BF9045B
POP LABEL LW60 GM FOR EXPORT
POP LABEL
104
Remarks
S-VIDEO
CABLE
AUDIO
CABLE 22P
AUDIO
CABLE
ASSY
S-VIDEO
CABLE
Ch6. Part lists
Location
Part Number
Specification
HWM33
3850BF9046A
POP LABEL LW60, 70 PM FOR DOMESTIC
POP LABEL
HWM33
3850BF9046B
POP LABEL LW60, 70 PM FOR EXPORT
POP LABEL
HWM34
3850BB9196A
LABEL HUNTER 17.1 WIDE SYSTEM
ID LABEL
HWM34
3850BB9196B
ID SYSTEM HUNTER WIDE 17.1 FOR EXPORT
ID LABEL
105
Remarks
HWL29
HWL12
HWL30
HWL11
HWL31
HWL31
HWL10
HWL07
HWL27
HWL09
HWL03(15.4”)
HWL08
HWL34
HWL22
HWL29
HWL30
HWL18(17.1”)
HWL23
15.4 17.1 E XP LODE D V IE W
HWL15(15.4”)
HWL14(15.4”)
HWL13(15.4”)
HWL33
HWM20
3
HWL05(15.4”)
HWL20(17.1”)
HWL01(15.4”)
HWL16(17.1”)
HWM27
HWM27
HWL04(15.4”)
HWL19(17.1”)
HWL06(15.4”)
HWL21(17.1”)
HWM20
NRUB1
HWL32
HWL02(15.4”)
HWL17(17.1”)
HWM22
HWC08
HTM05
HTC05
NMEM1
HWC12
HWB01
HWM24
HWM02
HWM14
HWM17
HWS02
HWM01
HWC16
HWM13
HWM28
HWM15
HWM16(17.1”)
HWS01
HWM25
HWC07
HWM26
HTA04
HWM24
HWS03
HWM03
HWC17
HWC14(15.4”)
HWC15(17.1”)
HTA03
HTA05
HTA06
HTA01
HTA02
HWM23
HWM31
HWM29
HWM30
HWM33
HWD01(15.4”)
HWM23
HWD01(17.1”)
HWD03(15.4”)
HWD04(17.1”)
HWD02
HWM10(15.4”)
HWM12(17.1”)
HWM11
HWM22
HWM06
HWM05
HWM23
HWM07
HWM04
HWC09
HTA07
HWM34
HWM08
HWM09
HWC04
NMEM1
HWM23
HWM27
HWM27
HWM23
HWC11
HWC13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising