Technical Data Sheet fischer fixit 2K Epoxy Adhesive Metal 2K EF

Technical Data Sheet fischer fixit 2K Epoxy Adhesive Metal 2K EF
Technical Data Sheet
fischer fixit 2K Epoxy Adhesive Metal 2K EF
Properties
Value
Unit
Method / Remarks
System
Chemical Base
2K Epoxy Adhesive
Solvent
non
Consistency
paste-like
Density, hardener
1,93
g/ml
20 °C
Density, binder
1,5
g/ml
20 °C
Color, cured adhesive
metal gray
Color, hardener
white
Color, binder
black
Flashpoint
< 101
°C
Storage temperature range
< 25
°C
Shelf life
12
months
Handling
Application temperature range
+5 to +35
°C
Cure time for handling (belastbar
approx. 30
min
20 °C
Fully cured after
24
h
20 °C
Application
One or both sided; entire surface
Performance of cured material
Service temperature range
-50 to +120
Water resistance
good
Weathering resistance
good
Chemical resistance
refer to section below
Shear strength
1 - 25
version: 1/2008-04-01/TDB113GB
°C
N/mm2
25 °C, DIN 53283
page 1/3
Technical Data Sheet
Application
For strong bonding of: steel, iron, moulded parts, aluminium, alloys and many more to and under one
another, as well as for correction and repair of misplace drill holes, cracks and cavities.
Not suitable for PE, PP, Teflon® and silicone.
Properties / Features
- Highest adhesive strength and stability
- Fills in gaps
- May be drilled, ground and milled
- Easy to apply
- Liquid metal
- Withstands temperatures up to +120 °C
Surface cleaning
The parts to be joined together must be clean and free of oil and grease.
Directions for use
The parts to be joined together must be clean and free of oil and grease.
Do not use the adhesive in outside temperatures below +5°C.
Upon first use, cut off tip and squeeze out required quantity of adhesive, mix well until an even colour
is achieved. Apply the adhesive with a spatula.
After use, seal nozzle with attached cap (break out from centre of sliding part).
May be mechanically worked after 30 min, hardens completely after 24 hours.
Cleanup
Before hardening – with cleaning solvent or acetone, after – mechanical cleaning.
Storage
Store in a cool, dry place.
Chemical resistance
fischer fix it 2K Epoxy Adhesive Metal 2K EF is resistant to moisture, oil, diluted acids, alkalis and
many solvents.
Classification and Labelling
Xi Irritant / N Dangerous for environment
Reaction product: bisphenol-A/F-(epichlorhydrin); epoxy resin (number average molecular weight <=
700)
Contains epoxy constituents. See information supplied by the manufacturer.
Irritating to eyes and skin. May cause sensitization by skin contact. Toxic to aquatic organisms, may
cause long-term adverse effects in the aquatic environment. After contact with skin, wash immediately
with plenty of water and soap. Wear suitable protective clothing, gloves and eye/face protection.
Avoid release to the environment. Refer to special instructions/safety data sheets.
version: 1/2008-04-01/TDB113GB
page 2/3
Technical Data Sheet
Only recycle when empty.
For further safe handling information on this product, consult the Material Safety Data Sheet (MSDS).
The information in this adhesives brochure and our application-technology consulting, verbally and in
writing, is given to the best of our knowledge, but is non-binding and is not a guarantee in the sense
of § 443 BGB. We recommend that, before using our products, you check the suitability for the
intended application. As the individual product can be used for a wide range of applications and the
conditions on site that cannot be estimated, we also recommend testing the bonding before using the
product.
version: 1/2008-04-01/TDB113GB
page 3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement