advertisement
CLUB SERIES VERITCAL
DUMBBELL RACK
Part # 7189501
Rev B.
ASSEMBLY INSTRUCTIONS
1 Revision:3/01/02
PARTS LIST
KEY
1
4
5
2
3
PART #
ACUAP04-0047
DESCRIPTION
FRAME
ACUAP01-0083 3 X 2 X 18” TUBE
ACUP02-0044 DUMBBELL CHANNEL
3102922
3102905
3/8 X 2-3/4” BOLT
3/8 X 3-3/4” BOLT
QTY
1
4
3
2
2
KEY
6
7
8
9
10
OR
PART #
3102807
3102514
6866701
6866601
6866602
6866603
DESCRIPTION
3/8” LOW HEIGHT LOCK NUT
3/8” SAE WASHER
3/8” RH WASHER
BLACK RH CAP
WHITE RH CAP
PLATINUM RH CAP
QTY
7
14
14
6
8
8
Tools Required for Assembly
* Rubber mallet or hammer
* 9/16” wrench
* Ratchet with 9/16” socket
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
0
1/2
1
1/2
2
1/2
3
2
1/2
4
1/2
5
1/2
6
8
RH
WASHER
4 3/8 X 2-3/4” BOLT
5 3/8 X 3-3/4” BOLT
9 10
RH CAP
(BLACK/WHITE/PLATINUM)
6
3/8” LOW
HEIGHT LOCK
NUT
7
3/8” SAE
WASHER
3
FIGURE 1
1
10
3/8 X 2-3/4” 4
7
8
2
6
STEP 1:
• SECURELY assemble the two 3 X 2 X 18” TUBES (2) to the FRAME (1) using eight RH CAPS (10), four 3/8 X 2-3/4” BOLTS
(4), eight 3/8” SAE WASHERS (7), eight 3/8” RH WASHERS (8) and four 3/8” LOW HEIGHT LOCK NUTS (6) as shown in
FIGURE 1. (IMPORTANT! Note orientation of TUBES.)
0
1/2
1
1/2
2
1/2
3
4
1/2
4
1/2
5
1/2
6
FIGURE 2
1
6
3
8
3/8 X 3-3/4” 5
7
9
STEP 2:
• SECURELY assemble two DUMBBELL CHANNELS (3) to the FRAME (1) using six BLACK RH CAPS (9), three 3/8 X 3-3/4”
BOLTS (5), six 3/8” SAE WASHERS (7), six 3/8” RH WASHERS (8) and three 3/8” LOW HEIGHT LOCK NUTS (6) as shown in FIGURE 2.
5
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10 YEARS STRUCTURUAL FRAME
3 YEARS PILLOW BLOCKS, PULLEYS, WEIGHT PLATES AND GUIDE RODS
1 YEAR
90 DAYS
CABLES
UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action
CLEAN
Upholstery
Guide Rods
Hand Grips
DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
X
INSPECT
Visual Overall X
Cables
Hardware
Frame
Hand Grips
LUBRICATE
Guide Rods
X
X
X
X
X
X
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800)351-3737.
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES PLATE TREE. If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at (800)
351-3737.
6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project