Lightolier DPA2G12LS232 User's Manual
Lightolier DPA2G12LS232 User's Manual
Add to My manualsadvertisement
Deepcel Plus
DPA2G12LS232
Page 1 of 2
• 5" deep body.
• 80.0% efficient.
• Clean contoured interior.
• Eyeleted heat removal vents in fixture ends.
• One piece housing.
• Black exterior for cooler ballast operating temperature.
• Hemmed over side rails for safe handling.
• Fixture ends turned-in for safe handling.
• Built-in earthquake clips (patent no. 5,072,344).
• Pre-anodized aluminum parabolic louver.
• Vertical grain louver eliminates reflected lamp images on cross baffle.
• Spring loaded latches.
• 18 gauge steel hinges.
• Louver frame with integral positive light stop.
• Louver has protective film dust guard.
• Construction to meet NYC Code or Chicago Plenum requirements is available.
2' x 4' Recessed Fluorescent, 3", 12 Cell Parabolic Louver
Static or Air Supply/Return, 2 Lamp, T8 or T5
Mounting Methods
G exposed T-grid ceiling.
T exposed slot T-grid ceiling.
Dimensions
24"
1/4" max.
1-1/2" max.
15/16" or 1"
F concealed Z-spline ceiling.
1-7/8" max.
24"
F plaster ceiling/flanged.
9/16"
Plaster Opening
24-1/8"
1-1/8" min.
3-3/4" max.
24-11/16" drywall kit.
Type “G”
Fixture
Support
(by others)
Drywall Kit
(See Options)
Drywall
(by others)
24-11/16"
Order Catalog Number: FK92X4.
1-1/8" min.
3-3/4" max.
13/16"
•
3" Nominal
•
6" (152mm)
24" (610mm)
2" x 2-1/2" access plate with two K.O.s
(7/8" dia.)
Job Information
Job Name:
Cat. No.:
Lamp(s):
Volts/Ballast:
39-1/4" (997mm)
47-31/32" (1218mm)
Type:
5"
(127mm)
Air supply slots
(DPA only)
Lightolier a Genlyte company www.lightolier.com
Technical Information: (978) 657-7600 • Fax (978) 658-0595
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2007 a Genlyte company Section 2/Folio G51-40 Rev. A
08/07
Deepcel Plus
DPA2G12LS232
Page 2 of 2
Photometry
Model No. DPA2G12LS232120SO
THIS REPORT IS BASED ON PUBLISHED INDUSTRY PROCEDURES • FIELD PERFORMANCE MAY VARY FROM LABORATORY PERFORMANCE.
2' x 4' Recessed Fluorescent, 3", 12 Cell Parabolic Louver
Static or Air/Return, 2 Lamp, T8 or T5
LER = FP - 64.4 IW - 61.6 BF - 0.87
Comparative yearly lighting energy cost per 1000 lumens = $3.73
coefficients of utilization — zonal cavity method
RF 20
RC
RW 70
80
50 30
1
2
3
4
5
6
7
8
9
10
89
81
74
69
63
58
53
50
46
43
85
76
67
59
53
48
43
39
36
33
83
71
61
53
46
41
36
32
29
27
50
41
37
34
32
80
71
63
56
50
45
visual comfort probability (VCP) average 100 fc; reflectances 80/50/20 room size ceiling height
W L 8.5
10.0
13.0
16.0
60
60
60
60
60
40
40
40
40
40
40
30
30
30
30
30
20
20
20
20
100
100
100
100
20
30
40
60
20
30
40
60
80
20
30
40
60
80
100
30
40
60
80
100
40
60
80
100
80
83
83
83
83
86
86
86
86
83
86
86
86
86
86
86
86
86
86
86
86
86
86
86
75
78
81
81
78
81
84
84
84
82
83
85
85
85
85
84
85
85
85
85
85
85
85
85
76
75
79
81
75
75
78
81
81
78
77
80
83
83
83
79
82
84
84
84
82
84
84
84
78
80
81
81
75
76
78
79
79
81
73
74
77
77
77
82
73
74
77
77
86
76
77
80
20
50
30
35
32
29
26
78
68
59
51
45
40
10
31
28
25
22
76
64
55
47
40
35
8.5
84
84
84
84
84
81
84
84
84
84
84
81
84
84
84
84
76
80
80
80
84
84
84
84
50
40
36
33
31
77
69
61
55
49
44 ceiling height
10.0
13.0
16.0
79
81
80
80
80
77
79
81
81
80
80
75
77
80
80
80
71
74
77
77
80
80
80
80
78
80
80
80
76
78
80
80
80
75
74
76
79
79
78
71
71
73
76
76
71
70
73
76
74
77
77
77
74
73
75
76
76
76
71
71
73
75
75
75
71
70
73
76
77
72
72
74
20
30
30
35
31
28
26
75
66
57
50
44
39
10
31
27
25
22
74
63
54
46
40
35
Ordering Information
Explanation of Catalog Number. Example: DPA2G12LS232120SOCP
2 S 2
Deepcel Plus
Parabolic:
Pre-anodized aluminum louver
DP
Body Style:
A=Air Supply
S=Static
Standard Deepcel
Fixture
Width
Ceiling Type:
G= Grid
(lay-in T bar)
F= Flanged (over lap) Z spline and plaster frame
T= Slot grid or two-directional concealed T
(see options)
DY
For NYC Code – I.B.E.W. Manufactured
Number of
Cells:
12=2 rows of 6
18=3 rows of 6
24=3 rows of 8
32=4 rows of 8
Louver Finish:
L = Low iridescence
Semi-specular
(standard)
P =Low iridescence
Specular
W =White Baked
Enamel
ND For NYC Code – Local 3 Manufactured
5½" Deep Body
Single "V"
Reflector
Options/Accessories
Plaster Frame: Catalog Number: PF24.
Continuous Row Installation: For F type fixtures, half width flanges are required between fixtures. Order Catalog Number: 2FC TRIM CSP (each joint).
Radio Interference Filter: To order one RIF per fixture; SUFFIX: R. To order one RIF per ballast;
SUFFIX: B.
Electrical Wiring Options: Consult factory.
Air Closure Strip: SUFFIX: ACS4 (factory installed).
Drywall Kit: Order Catalog Number: FK92X4. (Request Folio OA30-10 Rev. A).
Chicago Plenum: SUFFIX: CP.
Specifications
Performance: In an installation of 2 lamp 32W luminaires in a room cavity ratio of 1, reflectance 80% ceiling, 50% wall, 20% floor, the C.U. shall not be less than .85. To prevent glare the VCP shall be not less than 75 either lengthwise or crosswise (at 100fc level) and the average brightness at 65° shall not exceed 1606 candelas per square meter. To control veiling reflections, luminaire output in the 30°-90° zone shall not be less than 72.0%.
Air Handling (DPA only) side air pasaages for air supply or air return. Supply air is discharged vertically. Optional side closure strips. Air return is also provided through the lamp compartment through fixture body ends.
Materials: Chassis parts are die-formed code gauge cold rolled steel. Housing is ribbed for rigidity with side rails hemmed over and housing ends turned-in for safe handling. Louver is pre-anodized aluminum (Coilzak ® or equal.
Lamp
Quantity
Lamp Type/
Fixture Length:
32=32W T8
28=28W T5
54=54W T5
(Nominal 48")
Voltage:
120, 277 or
UNV=120-277
Options:
Add appropriate suffix to catalog no., ie: (CP)
Ballast Type:
1-2 Lamp Elec. T8
< 20THD < 10THD
SO *
1-2 Lamp 28W Elec. T5 –
1-2 Lamp 28W Elec. T5 –
H
P
I
I
*
†
† PG ††
1-2 Lamp 54W Elec. T5 –
LOL T8 Dimming PS
† PG ††
–
Other dimming options. Consult factory.
† *Instant Start Standard
† †Instant Start (120, 277 or UNV)
††Program Rapid Start (UNV only)
NOTE:
For T8 UNV, you must use H
I Ballast Code.
Specifications (continued)
Finish: Chassis exterior–black baked polyester enamel. Cavity–white baked polyester enamel minimum 86% reflectance. Phosphate undercoating. Louver–low iridescence semispecular anodized vertical grain aliminum reflector sheet is standard.
Electrical: Thermally protected class “P” ballast C.B.M. approved, non PCB. If K.O. is within 3" of ballast, use wire suitable for at least 90°.
Labels: I.B.E.W. UL and ULc Listed.
Job Information Type:
Lightolier a Genlyte company www.lightolier.com
Technical Information: (978) 657-7600 • Fax (978) 658-0595
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2007 a Genlyte company Section 2/Folio G51-40 Rev. A
advertisement