User Guide - Thomann.de
DOEPFER
MIDI Master Keyboard
LMK4+
User's Guide
User's Guide LMK4/LMK4+
INDEX
1.
1.1
1.2
1.3
1.4
1.5
Operation (Hardware)
Power Supply
MIDI-Interface
Connection of External Controllers and Footswitches
Controls
Operating and Security Instructions
2.
2.1
2.2
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
2.3.8
Operation (Software)
Switching the keyboard ON
Menu Structure
Description of Menus
Preset
Program Change / Bank Select
Real Time / Master Channel
Split
Controller Assign / Activate
User-defined Controllers
Parameters / Name
Panic
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Appendix E:
Appendix F:
Velocity response and aftertouch curves tables
Pin assignment of power and foot controller jacks
Conversion table Bank/Numbers to Decimal System
Quick reference table of functions
Resetting all Presets
Technical Data LMK4+
The difference between the MIDI Masterkeyboards LMK4 und LMK4+ is the type of keys. LMK4 uses weighted
plastic keys while LMK4+ has keys with real hammer mechanics. The control of LMK4 and LMK4+ is identical. Both
instruments are delivered with the combined LMK4/LMK4+ manual.
LMK4 User's Guide Page 2
1. OPERATION (Hardware)
1.1 Power Supply
The LMK4 does not have a built-in power supply. Instead it uses a plug-in type external power supply (AC adapter).
One reason for this feature is electrical safety. Keeping danger voltages (main) out of the keyboard increases the
electrical safety. Therefore a external power supply of high quality and safety should be used. If the keyboard is used
in Germany the external power supply must be VDE approved.
Another reason for the external power supply is the fact that line voltages and plug types vary considerably from
country to country. Using a plug-in external supply the LMK4 can be used any where with a locally purchased power
supply, thus keeping the retail price down.
The power supply must be able to deliver 7-12 VDC unstabilized voltage, as well as a minimum current of 400mA.
The LMK4 is switched ON by plugging the AC adapter into a wall outlet and connecting it to the appropriate jack on
the back of the keyboard case. There is no separate ON/OFF switch.
If the polarity of the power supply is incorrect, the LMK4 will not function. However, there is no danger of damage to
the circuitry since it is protected by a diode. A power supply for 230V AC and European type plug is included with the
LMK4. Any other type of power supply and must be purchased locally by the user.
If you are using the power supply shipped with LMK4 you may find the pinout of the LMK4 power jack in the appendix
B.
Once the power supply has been plugged in a message should appear on the display (e.g. "LMK4 V1.00" for
indicating the software version 1.00) and the 8 LED's should flicker. If this does not happen the power supply is either
defective or does not have proper polarity/voltage/current. After that the LMK4 should go into preset-mode (see
chapter 2.3.1 for details). The first LED should be illuminated.
1.2 MIDI-Interface
LMK4 features 4 MIDI outputs with 2x2 parallel connected outputs. This means that the 2 MIDI outputs labelled "MIDI
OUT 1" transmit the same MIDI informations. Same is valid for the MIDI outputs labelled "MIDI OUT 2". In the SPLIT
menu (see chapter 2.3.4) the allocation of the split zones to the MIDI outputs is defined.
Connect MIDI outputs of the LMK4 with MIDI-IN of the device(s) to be controlled by the LMK4 (i.e. expander,
sequencer, synthesizer, sampler etc.). If several devices are to be controlled by the LMK4 you may use the 4 MIDI
outputs of the LMK4. If you want to control more than 4 devices they have to be chain-linked via MIDI-THRU/IN.
Alternatively one may utilize a so-called MIDI-THRU-box.
The LMK4 features a MIDI input. This input may be connected to another MIDI keyboard oder MIDI base pedal. The
incoming MIDI data can be managed by the LMK4 as split zone. So it is possible to modify the MIDI channel or the
transposition of incoming MIDI data and to treat the external device as a split zone of the LMK4. The MIDI input can
be used also for switching the LMK4 presets via incoming Program Change events or for transfering LMK4 memory
data via MIDI dump. For this purpose a suitable MIDI dump or editor software is required.
MIDI cables are not included with the LMK4.
1.3 Connection of External Controllers & Footswitches
Located on the rear of the keyboard case are three jacks labelled "EXT. INPUTS" for
hooking up a double-footswitch ("SWITCHES") and two foot pedals ("CTRL1", "CTRL2"). Allocation of these
controllers to the various MIDI-functions is completely user-defined (see chapter 2.3.5). The name of the external
inputs for programming is EX.SW1 and EX.SW2 for the foot switches and E.CTR.1 and E.CTR.2 for the foot
controllers.
Do not connect the footswitches or foot controllers unless the LMK4 is switched OFF (i.e. unplugged). While power
on the LMK4 electronics checks the levels of the foot switches and assumes that these levels are the "off" states. So
do not operate the foot switches while turning power on. This feature allows the use of foot switches with contacts
open at rest as well as those closed at rest.
The foot switches and foot controllers are not included with the LMK4 and have to be ordered separately if required. A
suitable foot switch is the DOEPFER VFP2, a suitable foot controller is the DOEPFER FP5. The LMK4 will work
without the foot switches and foot controllers, although the corresponding functions will not be available to the user in
LMK4 User's Guide Page 3
that case. If you are not using VFP2 or FP5 you may find the pinout of the ext. input jacks in the appendix B as well
as the type of potentiometer required for the foot controller.
For details regarding assignment of MIDI functions to the foot controllers (e.g. volume, sustain, soft pedal and so on)
refer to chapter 2.3.5 Controller Assign / Activate.
1.4 Controls
The LMK4 features the following controls and displays:
•
•
•
•
•
•
•
Illuminated display with two rows of 16 characters each
24 buttons in three rows of 8 buttons each
Upper row: MENU-buttons
Middle row: BANK-buttons
Lower row: NUMBER-buttons
8 LED's (serving as indicators for the MENU-buttons)
2 Wheels (one spring-loaded)
2 Sliders
1 Rotary potentiometer
1 Rotary encoder (Data-entry dial)
The two wheels, the two sliders and the rotary potentiometer can be used for any MIDI-function desired by the user
(e.g. any continuous MIDI controller). The rotary encoder (data-entry dial) is primarily used for data entry purposes.
Rotary
Potentiometer
CTR3
Rotary
Encoder
(Data Entry)
LC Display
LEDs
Menu
1
2
3
4
5
6
7
8
Bank
Number
1
2
3
4
5
6
7
8
Wheel 2
Wheel 1
CTR1 CTR2
Sliders
Adjustment of LC-Display
The display can be adjusted by means of 2 potentiometers, one for contrast and one for background illumination. If
you wish to change the factory settings insert a thin, insulated screwdriver into the holes to the left and right of the
display and adjust the potentiometers to the desired settings.
In addition LMK4 is equipped with a monophonic After Touch sensor below the keys that is activated if you put
pressure on the keys pressed down. The After Touch sensor of the LMK4 is treated like any other controller (i.e. like
wheels, sliders ....). This means it is not limited to send MIDI after touch data but can be used for any MIDI-function
desired by the user (e.g. any continuous MIDI controller).
LMK4 User's Guide Page 4
1.5 Operating and Security Instructions
Please follow the given instructions for use of the instrument because this will guarantee correct instrument operation.
Due to the fact that these instructions touch on Product Liability, it is absolutely imperative that they be read
carefully. Any claim for defect will be rejected if one or more of the items was observed. Disregard of the instructions
can endanger the 6 month warranty.
The instrument may only be used for the purpose described in this operating manual. Due to safety reasons, the
instrument must never be used for other purposes not described in this manual. If you are not sure about the intended
purpose of the instrument please contact an expert.
The instrument may only be operated with the voltage written on the power input on the rear panel. Before opening the
case disconnect the power plug.
All eventual modifications must only be carried out by a qualified person who will follow the valid safety instructions.
Every modification should becarried out only at the manufacturer or an authorized service company. Any modification
not released by the manufacturer leads to the extinction of the operation permission.
With the introduction of a third person the warranty will be lost. In case of a destroyed warranty seal, any warranty
claim will be rejected.
The instrument must never be operated outdoors but in dry, closed rooms. Never use the instrument in a humid or
wet environment nor near inflammables.
No liquids or conducting materials must get into the instrument. If this should happen the instrument must be
disconnected from power immediately and be examined, cleaned and eventually be repaired by a qualified person.
Never subject the instrument to temperatures above +50°C or below -10°C. Before operation the instrument should
have a temperature of at least 10°C. Do not place the instrument into direct sun light. Do not install the instrument
near heat sources.
Keep the top side of the instrument free in order to guarantee proper ventilation, otherwise the instrument could be
overheated. Never place heavy objects on the instrument.
All cables connected with the instrument must be checked periodically. If there is any damage the cables must be
repaired or replaced by an authorized person.
Transport the instrument carefully, never let it fall or overturn. Make sure that during transport and in use the
instrument has a proper stand and does not fall, slip or turn over because persons could be injured.
Never use the instrument in the immediate proximity of interfering electronic devices (e.g. monitors, computers) since
this could create disturbances within the instrument and corrupt memory data.
The exchange of electronic parts (e.g. EPROMs for software update) is allowed only if the instrument is disconnected
from power supply.
The instrument should only be shipped in the original packaging. Any instruments shipped to us for return, exchange,
warranty repair, update or examination must be in their original packaging! Any other deliveries will be rejected.
Therefore, you should keep the original packaging and the technical documentation.
When using the instrument in Germany, the appropriate VDE standards must be followed. The following standards
are of special importance: DIN VDE 0100 (Teil 300/11.85, Teil 410/11.83, Teil 481/10.87), DIN VDE 0532 (Teil
1/03.82), DIN VDE 0550 (Teil 1/12.69), DIN VDE 0551 (05.72), DIN VDE 0551e (06.75), DIN VDE 0700 (Teil 1/02.81,
Teil 207/10.82), DIN VDE 0711 (Teil 500/10.89), DIN VDE 0860 (05.89), DIN VDE 0869 (01.85). VDE papers can be
obtained from the VDE-Verlag GmbH, Berlin.
LMK4 User's Guide Page 5
2. OPERATION (Software)
2.1 Switching the Keyboard ON
When the keyboard is switched ON a message regarding the software version will appear on the
display for several seconds (e.g. "LMK4 V1.00"). In addition the LED's will flicker for several seconds. After that the
keyboard will go into preset-mode (see below for details) and will call up preset no. 1.
NOTE: When the keyboard is activated for the very first time, the presets will contain random
values since the RAM contains random data. In order to completely initialize the keyboard (i.e.
to set all 128 presets to the same standard values) you have to follow the procedure described in the appendix.
Normally it is not necessary to initialize the memory as this is performed during the final check of the device in the
factory.
2.2 Menu Structure
There are 8 menus available. They are selected via the 8 uppermost buttons. These are referred to
as MENU-buttons. Pressing one will access the corresponding menu. The LED's serve as visual
indicators of the menu selected. You leave a menu simply by pressing another MENU-button. The 8
MENU-buttons correspond to the following menus (from left to right):
1
2
3
4
5
6
7
8
PRESET
PROGRAM CHANGE
REALTIME/MASTER CHANNEL
SPLIT
CONTROLLER ASSIGN/ACTIVITY
USER DEFINED CONTROLLERS
PRESET PARAMETERS/NAME
PANIC
When the keyboard is switched on it will always go to the PRESET-menu. In the next few
paragraphs we will briefly discuss the functions of each of the 8 menus, followed by the operating
procedure for each menu.
1: PRESET
The LMK4 keyboard allows the storage and recalling of up to 128 complete keyboard settings, referred to as
"presets". Each preset contains data about all 8 keyboard zones with their respective
MIDI-channels, transpositions, allocation and activation of controllers, velocity-response curves, program numbers,
volumes, preset-name, etc. The PRESET-menu is used to call up or store the
presets. The detailed description of the PRESET-menu also includes information on the
MIDI-DUMP-function of the LMK4.
2: PROGRAM CHANGE / BANK SELECT
This menu serves to send program numbers (MIDI-program change instructions) and bank select data (i.e. MIDI
controller #0 and #32) in direct mode to select the programs and banks of the MIDI-instrument(s) connected to the
LMK4. The program change and bank select instructions are transmitted via the MIDI-master-channel selected at the
time (also refer to menu 3).
Independent of this, in menu 4 each of the 8 keyboard zones can be assigned a program and bank number which is
sent on the MIDI-channel of the keyboard zone when PRESET is called up (see menu 4: SPLIT).
3: REALTIME / MASTER-CHANNEL
This menu is used to directly transmit MIDI-realtime information (i.e. START, STOP, CONTINUE,
CLOCK) and to select the MIDI-master-channel on which the LMK4 transmits the direct-mode
program changes and bank select data.
LMK4 User's Guide Page 6
4: SPLIT
The LMK4 handles up to 8 different keyboard areas (split areas, split zones, split range) simultaneously. Overlaps of
the zones are possible (i.e. some keys are used by more than one zone). Each zone is assigned a MIDI channel and
to one of the 2 MIDI outputs. The SPLIT-menu
is used to define the parameters of each of the 8 keyboard zones. The SPLIT-parameters are as follows:
•
•
•
•
•
•
•
•
•
LOWER and UPPER key
MIDI channel
MIDI output 1 or 2 or both
Transposition
Velocity-response curve
Aftertouch curve
Program number
Bank Select number (= Controllers #0 and #32)
Volume
In addition in this menu is defined if the zone is used for the (internal) keyboard or the (external) MIDI input.
5: CONTROLLER ASSIGN/ACTIVITY
This menu has 2 different functions:
•
•
Assignment of controllers (i.e. Sliders, Wheels, After Touch etc.) to MIDI-functions
Activation of the controllers in the keyboard zones
First, each controller is assigned a particular MIDI-function (i.e. pitch bend, modulation, volume, sustain, etc.). Then
the user can decide for each individual keyboard zone whether or not the respective controller is active in that
keyboard zone, i.e. whether or not the corresponding data of the controller will be transmitted on the MIDI channel
and MIDI output of that keyboard zone.
6: USER DEFINED CONTROLLERS
In this menu user-selected controllers (UD1...UD8), which can be used in menu 5, are defined.
7: PRESET PARAMETERS/NAME
In this menu the following preset-parameters are defined:
•
•
•
•
•
•
•
Name of the preset
Preset-pointer (=Number of the next preset reached when switching presets with footswitch)
Realtime parameters of the preset (i.e. transmission of START, STOP, CONTINUE or none of these when the
preset is called up)
Scale Black Parameter (Adjustment of velocity-response of the black keys)
Manual DUMP-function (Dumps contents of Preset-memory via MIDI)
Transferring the volatile memory data into the non-volatile memory after receiving a MIDI dump
ATP-Parameter (Positive/negative pitch-bend when aftertouch-sensor has been assigned to pitch-bend-function)
8: PANIC
This menu provides a PANIC-button which can be used in any operational mode. In addition, the
menu also provides 16 "pseudo-panic-buttons" (for the 16 MIDI-channels) to be used in the event of
one of the instruments connected to the LMK4 not recognizing the "ALL NOTES OFF"-instruction.
LMK4 User's Guide Page 7
2.3 DETAILED DESCRIPTION OF MENUS
2.3.1 Preset (1)
This menu is entered by pressing the leftmost MENU-button. Switching the keyboard ON will also
activate this menu. It serves to call up and store presets. A preset is the sum of all information defining a keyboard
configuration. All data about the 8 keyboard zones (i.e. external input or internal keyboard, UPPER/LOWER key,
MIDI channel, Output, Transposition, Velocity and After Touch table, active controllers, Program number, Bank
number, Volume), master-channel, tempo (MIDI clock), allocation of controllers, desired realtime-instructions during
preset call-up, preset pointer and preset name. 128 such presets can be defined by the user and stored for call-up in
the PRESET-menu.
After pressing the PRESET-menu-button the following message appears on the display:
PRS:XXX / PRESET-NAME
B:0YY / N:00Z / >PPP
The upper row lists the preset number selected (XXX=1...128) on the left, the name of the preset selected is shown on
the right. The lower row indicates the bank number on the left (YY=1...8), the
number within that particular bank is shown in the middle (Z=1...8) and the preset pointer is displayed on the right
(PPP=1...128). The preset pointer shows the number of the preset which the LMK4 will jump to when the presets are
switched via one of the footbuttons (assuming this option is being utilized).
Each bank consists of 8 presets. A bank is selected via one of the 8 BANK-buttons, the number
within the bank is chosen by means of one the 8 NUMBER-buttons. With this method only 64 presets are available (8
BANK-buttons x 8 NUMBER-buttons = 64 combinations). So the PRESET-menu-button itself is used to switch
between the presets 1...64 and 65...128. The button has to pressed to toggle between the two ranges.
Note: The term "bank" used in this context has nothing to do with the MIDI program bank that is selected by the
MIDI controllers #0 and #32. The MIDI association introduced the MIDI bank term after we used this term for the
bank/number structure of our keyboards. For details regarding the MIDI bank term refer to chapter 2.3.2 PROGRAM
CHANGE / BANK SELECT.
Call-up of a Preset
The two bottom rows of buttons on the LMK4 are used to call up a preset from the PRESET-menu. The upper row of
buttons is used to select the bank number, the lower row to select the number within the bank. Each bank consists
of 8 presets. In combination with the PRESET-menu-button for toggling between 1...64/65...128 all 128 presets can
be adressed.
A preset is called up if one of the 8 NUMBER-buttons has been pressed after selecting the
bank with one of the 8 BANK- buttons and selecting the range 1...64/65...128 with the PRESET-menu-button. Using
the BANK-buttons or PRESET-menu-button alone will call -up the preset. Following this procedure each of the 128
presets can be called up directly.
Once a preset has been called up it is loaded into the so-called work-memory. This memory always contains the
preset currently active. Only the values contained in the work-memory can be modified via the other menus. In order
to modify a preset it has to be called up and loaded into the work-memory, modified while residing in the work
memory and then be stored again in its modified form.
When a preset is called up the content of the work memory is overwritten. Similarily, when storing the content of the
work-memory in one of the preset-memory locations, the old preset stored there is overwritten.
In addition a preset can be called-up by receiving a suitable Program Change message at the MIDI input. The MIDI
channel of the Program Change message has to match to master channel of the LMK4 adjusted in menu 3 and the
preset change via MIDI input must be active (details see chapter 2.3.3: REAL TIME / MASTER CHANNEL). If the
presets of the LMK4 seem to alter automatically check if incoming Program Change messages are the reason for
this behaviour.
If you do not want to alter the presets via incoming Program Change messages deactivate this function in menu 3.
LMK4 User's Guide Page 8
Storing a Preset
The data of the work-memory can be stored via the PRESET-menu. It can be placed in one of the
128 preset-memory locations by pressing the PRESET-menu-key and the PANIC-menu-key (first and last menubutton) simultaneously. The following message appears on the display:
STORE MODE OK?
Also, all 8 LED's will be illuminated as a warning! Next the desired BANK-button and possibly the PRESET-menubutton (to alter the range 0...64/65...128) to be pressed, followed by a NUMBER-button. The content of the workmemory is now stored into the preset-memory location thus selected.
CAUTION! Any preset stored at that location will be overwritten, i.e. it will be irretrievably lost! Store presets only in
locations that do not contain presets which are still needed. If any MENU-button is accidentally pressed the LED's
will go off and the storage process will NOT take place.
Storing/Downloading of the Preset-memory contents via MIDI (DUMP/REQUEST)
In order to store or download the content of one or all presets via MIDI the LMK4 must be connected via MIDI In and
MIDI Out to a MIDI-capable computer with appropriate "Dump"-software capable of
requesting, storing and transmitting data to and from the LMK4 (e.g. PC or MAC with MIDI interface, ATARI ST).
MIDI-OUT 1 of the LMK4 is connected to MIDI-IN of the computer, MIDI-OUT of the computer is connected to MIDI-IN
of the LMK4.
Note: During data transmission of any kind between computer and LMK4 no other data can be transferred (like Note
on/off, Controller, Program Change). So it does not make sense to play on the keyboard or to operate one of the
controllers during a data transmission.
There are three ways to store preset-data via MIDI:
1. Manual dump of all presets (TRANSMIT-MULTI-DUMP)
This feature is covered by a menu-item in menu 7 ("PARAMETERS"). When pressing the fourth
BANK-button while in main menu 7, all stored data in the LMK4 is dumped via MIDI-OUT in accordance with the
Exclusive System Specifications of LMK4. MIDI-OUT of the computer and MIDI-IN of the LMK4 do not have to be
connected in this case. However, the computer must be in the appropriate standby-mode in order to properly receive
and store the incoming data.
2. Requesting dump of all presets via MIDI-IN (TRANSMIT-MULTI-DUMP)
This option requires the sending of a DUMP-request by the computer to the LMK4 via MIDI-IN. Once the LMK4
receives the request it dumps the content of the entire PRESET-memory via MIDI-OUT 1 (again in accordance with
the exclusive system specs). Except for the fact that it is triggered by an external request this data-dump is identical
to the manual dump described in the previous paragraph.
3. Dump-request for a single preset (TRANSMIT-DUMP)
Identical to item 2 except only the data for one preset is transmitted (as opposed to the content of
the entire preset-memory).
There are two options to load data from hardisk/diskette into the LMK4:
1. Downloading new data for the entire preset-memory (RECEIVE-DUMP)
Note: This function will overwrite all preset-data stored in the LMK4 at the time. If the existing data hasn't been saved
yet on disk/diskette, this must be done prior to using this function or loss of all old data will result. After receiving the
dump the data are stored in the volatile memory (RAM) of the LMK4 and are automatically transferred to the nonvolatile part of the memory (EEPROM). This process requires about 2 minutes. During this period it is not possible to
play on the keyboard or operate one of the controllers or to receive MIDI data. A message in the display informs
about the state of memory transfer.
LMK4 User's Guide Page 9
2. Downloading data for a single preset (RECEIVE-DUMP)
Same as item 1, except that only a single preset is being overwritten. After receiving the single dump the data are
stored in the volatile memory (RAM) of the LMK4. A external Store message must follow the dump to transfer the
data to the non-volatile memory. Alternatively a manual memory transfer has to be carried out (see chapter 3.3.7).
If an error is detected during the transmission ("Checksum error"), it is immediately interrupted and every second LED
flashes as a visual indication of an error. By pressing any MENU-button one can return to normal operating mode.
Since error checks occur after each individual preset-data transmission, at most only one preset can contain
incorrect data.
It is possible to receive dumps from the preceding keyboard LMK3 but in this case only the first 64 presets are
received and a error message after receiving preset 64 apears.
The System Exclusive specification of the LMK4 is available free of charge from our internet pages
(www.doepfer.com) or in printed form if you send us 5 international reply coupons.
2.3.2 Program Change / Bank Select (2)
This menu is called up by pressing the second MENU-button from the left. It is used to send MIDI Program-Change
and Bank-Select (Controller #0/32) messages directly to the MIDI-instruments connected to the LMK4. Data
transmission takes place via the MIDI-master-channel and output selected at the time (also refer to 2.3.3).
The following message appears on the display:
BANK: 00Y / NR: 00Z
VVV_WWW (CC): XXX
The abbreviation correspond to the following values:
00Y
00Z
VVV
WWW
CC
XXX
Bank, selected with the middle row of buttons (has nothing to do with MIDI program bank)
Number, selected with the lower row of buttons
Data value for MIDI Controller 0, adjustable with the left slider
Data value for MIDI Controller 32, adjustable with the right slider
MIDI channel, defined in menu 3 (master channel)
from bank/number buttons or rotary encoder resulting transmitted Program Change number
Sending a Program-Change-Message
The program-number (XXX) is selected via the two bottom rows of buttons or via the rotary encoder. When using the
buttons the upper row selects the memory bank (00Y), the lower row the number (00Z) within the bank. The term
"bank" used in this context has nothing to do with the MIDI program bank (see note in chapter 2.3.1). Each bank
contains 8 numbers. This accounts for 8 X 8 = 64 combinations = 64 programs. However, MIDI allows for 128
Program-numbers. Therefore the PROGRAM-button also serves to toggle between the first 64 program-numbers
(1...64) and the remaining 64 Program-numbers (65...128). The resulting program-number (XXX) takes into account
the offset adjusted via the PROGRAM-button.
Calling up a MIDI-program-number can only be accomplished by sequentially pressing the PROGRAM-button (if
necessary), a BANK-button and a NUMBER-button. Pressing only PROGRAM and/or BANK will not work. This way
each of the 128 programs can be called up directly, without having to go through other programs in between.
Alternatively the Program-Change messages can be send by using the rotary encoder. In this case only the resulting
Program-number appears in the display. The values of bank and number (00Y, 00Z) are not refreshed in this case.
Sending a Bank-Select-Message
The MIDI-Bank-Select-Message uses the MIDI-controllers #0 and #32 to define one of 16384 Program-Banks. The
complete bank instruction consists of a controller #0 event followed by a controller #32 event. Thus up to 16384 (=128
x 128) different program banks theoretically are available. A program change instruction following the bank select
instruction selects one of 128 sounds (programs) within the selected bank. Thus up to 2097152 (= 128 x 16384)
sounds theoretically are available. Of course no MIDI expander is able to produce 2097152 different sounds. If your
LMK4 User's Guide Page 10
expander, synthesizer or sampler recognizes the program bank instruction can be found in the MIDI implementation
chart of the unit.
The data values for Controller #0 and #32 are set with the sliders. The left slider corresponds to Controller #0, the right
to Controller #32. Both values appear in the display (VVV, WWW). Please refer to the user's guides of the devices
connected to LMK4 if the bank message is supported and which values for Controller #0/32 are used. Normally only a
few combinations of controller #0 and #32 are allowed to select one of the program banks availabe. Some
manufacturers also use only Controller #0 or #32 to select a program bank. Other manufacturers designate this
function as page, page select or variation.
If the sliders are assigned to other MIDI functions in menu 5 these are temporarily turned off during the Program/Bank
menu is selected as the sliders are used for Controller#0/#32 data. As soon as the Program/Bank menu is left these
functions are activated again.
All Program-Change and Bank-Select messages in this menu are sent on the MIDI-master-channel defined in menu
3.
Program-Change, Controller#0 and #32 can be defined for each split zone separately and stored in the presets. See
chapter 2.3.4 for details.
2.3.3 Realtime / Master-Channel (3)
This menu is selected by pressing the third MENU-button from the left. It is used to send MIDI-Realtime messages
and to select the MIDI-master-channel.
REALTIME / M_CHAN
S/T/C/K/ - / - / - /P
The bottom line is a symbolic representation of the functions which can be activated in this menu via
the BANK-buttons. The 8 letters and blank spaces correspond to the 8 BANK-buttons. A function is
activated by pressing the appropriate BANK-button. The abbreviations are as follows:
S= Start
T= Stop
C= Continue
K= Clock
P= Panic
The first four functions are suitable for controlling sequencers, drum-machines and other devices controlled by MIDIRealtime messages. When pressing the keys for START, STOP or CONTINUE, the corresponding MIDI-instruction is
immediately sent. If the START or CONTINUE function was selected, then the upper line of the display will show the
tempo in BPM (Beats per minute). The tempo can be adjusted between 50 and 250 BPM by means of the rotary
encoder (data-entry dial). Tempo is one of the parameters of PRESET and is stored in the preset-memory. If the
tempo is to be modified without first sending START or CONTINUE instructions, the CLOCK-button must be pressed
(fourth button from left in the middle row). The tempo currently set will be displayed on the upper line of the display
and can be changed via the rotary encoder.
If the PANIC-button is pressed, "ALL NOTES OFF"-instructions are sent on all 16 MIDI-channels and
all controllers are initialized. When using this "internal" panic-button one remains inside the menu.
Pressing the third MENU-button once more allows the selection of the MIDI-master-channel and the related functions.
The MIDI-master-channel is the channel on which the program change-instructions are sent in direct mode (see
chapter 2.3.2). It does not affect any other functions.
The lower line of the display will read:
MCHN: YYYYYYY : XX
LMK4 User's Guide Page 11
YYYYYYY is one of the following 4 choices that can be adjusted together with the MIDI-master-channel XX via the
rotary encoder:
POUT1&2
POUT1&0
POUT0&2
OUT1&2
external Preset call-up active / Outputs 1&2
external Preset call-up active / Output 1
external Preset call-up active / Output 2
external Preset call-up turned off / Output 1&2
In case of POUT... (first 3 choices) the Preset call-up via incoming MIDI Program-Change messages on the Masterchannel is active. If a suitable MIDI Program-Change message appears at the MIDI input of the LMK4 the new preset
is chosen. The incoming Program-number is identical to the Preset-number.
In case of OUT1&2 the Preset call-up option is turned off. The presets cannot be switched by incoming Programchange messages.
The combination of numbers 1&2, 1&0, 0&2 displays on which of the MIDI outputs the messages of menu 2 (i.e.
Program-Change and Bank-Select messages in direct mode) are sent. If these messages should appear on both
MIDI outputs 1&2 is chosen. If only one output is desired 1&0 (only output 1) or 0&2 (only output 2) is selected.
If you operate the rotary encoder at first the MIDI channel 1....16 within one mode is passed through. Exceeding
channel 16 the next mode is displayed. Falling short of 1 the previous mode is chosen.
The Master-channel/Preset call-up/output option is one of the parameters of PRESET and is stored in the presetmemory.
The bottom row of buttons is not used in this menu (i.e. the NUMBER-buttons).
2.3.4 Split (4)
This menu is selected by pressing the fourth menu-switch from left. It is used to define the split-parameters in the 8
keyboard zones. The following message appears in the display:
ZONE : 00X
L/U/C/T/D/A/P/V
The 8 BANK-buttons are used to select one of the 8 keyboard zones. The number of the zone (00X) selected will
appear in the top line of the display. The lower line of the display is a symbolic representation of the functions which
can be activated in this menu via the NUMBER-buttons. The 8 characters correspond to the 8 buttons. A function is
activated by pressing the appropriate switch. The abbreviations are as follows:
L
U
C
T
D
A
P
V
Lower key of the keyboard zone
Upper key of the keyboard zone
(MIDI-) Channel, source (int./ext.) and MIDI-output of the keyboard zone
Transposition of the keyboard zone
Dynamic table (= Velocity response table) for the keyboard zone
Aftertouch table for the keyboard zone
Program/Bank-number for the keyboard zone
Volume for the keyboard zone
Once a function has been selected via the corresponding NUMBER-button it is confirmed on the
display. The value currently set will be shown to the right of the function name.
In order to change one of the parameters selected with the NUMBER-buttons, the rotary encoder (data-entry dial) has
to be used. For example, to adjust the Volume for of a keyboard zone one has to select the zone with one of the
BANK-buttons, followed by selection of the VOLUME-function through pressing the right NUMBER-button. The
desired value is then set with the rotary encoder and will be shown on the bottom line of the display.
The UPPER and LOWER key parameters can also be adjusted via the keyboard. After pressing a
key (=lowest key) on the keyboard while in the LOWER KEY-submenu, the program will immediately
jump to the UPPER KEY-submenu. After another keyboard-key is pressed (=highest key) the
program jumps to the CHANNEL-submenu.
LMK4 User's Guide Page 12
In the submenu CHANNEL the MIDI-channel, the source and the MIDI-outputs for the zone are adjusted. By repeated
pressing of the submenu button (= number button 3) the following combination can be selected:
XX / O: Y&Z
XX is the source for the zone. Y and Z represent the MIDI-outputs 1 and 2 on which the MIDI messages of the zone in
question are passed through.. For the characters XX the following combinations can be selectet:
IN
EA
EO
EM
internal keyboard of the LMK4
external MIDI-input in ALL mode
external MIDI-input in OMNI mode
external MIDI-input in MONO mode
If the external MIDI-input is selected as source for the zone 3 different modes have to be distinguished:
The ALL mode (EA) does not change the MIDI-channel of the incoming note events. The parameters LOWER,
UPPER, TRANSPOSE and DYNAMIC take effect to the incoming note messages. This means that the incoming
note number to must be between LOWER and UPPER, are transposed with the TRANSPOSE value and pass
through the velocity curve (DYNAMIK). This mode should be selected if the incoming note messages should remain
unchanged to a great extent. With the following settings the incoming note messages will not be modified:
LOWER=0, UPPER=127, TRANSPOSE=0, DYNAMIK=1.
The OMNI mode is nearly identical to the ALL mode but the MIDI channel of the incoming note messages is set to
the MIDI channel of the zone. In OMNI mode the parameters LOWER, UPPER, TRANSPOSE, DYNAMIK and
CHANNEL are effective.
The MONO mode is identical to the OMNI mode with one exception: incoming note messages are processed only if
the MIDI channel of the incoming note messages corresponds to the MIDI channel of the keyboard zone. Incoming
note events with another MIDI channel are ignored. In this mode the MIDI input of the LMK4 acts as a MIDI channel
filter.
For the numbers X&Y the following combinations can be selected:
O:1&0
O:0&2
O:1&2
O:0&0
only MIDI-output 1 for this zone
only MIDI-output 2 for this zone
both MIDI-outputs for this zone
none of the MIDI-outputs (i.e. zone is turned off)
This assignment affects also the internal controllers (wheels, sliders, rotary potentiometer, after touch, foot switches
and foot controllers) but not via MIDI incoming controller messages.
Note: The MIDI-input of the LMK4 is intended for a second keyboard, synthesizer or base pedal. It is not suitable for
large MIDI data streams like those coming from a sequencer or computer. In this case there may occur timing
problems or loss if MIDI messages as the incoming MIDI data has to be merged with the MIDI data of the LMK4. For
such applications an external MIDI-merger (like the DOEPFER MMR4/4) should be used. Moreover one has to
consider that incoming MIDI data may be multliplied by a factor 8 if the MIDI input is routet to all zones. If there is
alreadya considerable data rate on the input the maximum tranfer limit of MIDI may be exceeded at the output(s)..
The TRANSPOSE-sub-menu permits entering the desired transposition by means of two keyboard-keys, as opposed
to using the data-entry dial. After pressing the first key the following message appears in the lower line of the display:
"TRSP.REF.:->"
followed by the number (i.e. MIDI-code) of the keyboard-key just pressed. The abbreviation stands
for "Transposition Reference Key". Next, the second key is pressed, the transposition then being
calculated with reference to the first key that was pressed. For example, if one wishes to transpose a
zone one octave higher one presses any desired key on the keyboard, followed by the same key in
the next higher octave.
In the two submenus DYNAMIC (Velocity-response curves) and AFTER TOUCH curves the velocity-response curves
and aftertouch curves are adjusted with the data-entry dial. Appendix A of this manual contains information about the
64 curves available for velocity-response, as well as for the 8 aftertouch curves. Graphical representations of these
curves can also be found in appendix.
In the sub-menu PROGRAM/BANK the program-number and bank-number (i.e. MIDI-controller #0/#32) for a keyboard
zone are set. Details regarding program-number and bank-number you will find in chapter 2.3.2 PROGRAM/BANK.
LMK4 User's Guide Page 13
If the display shows the message "STORE" on the upper right when the PROGRAM/BANK-button is pressed, then
the function in question is presently activated. This means that the program-number and bank-numbers entered will
be stored in the preset and will be sent when the preset is called up (see Menu 1: PRESET). If this is not desired in a
given keyboard zone, then the function can be disabled by pressing the PROGRAM/BANK-button once more. The
message "STORENO" will
then appear on the upper right of the display to indicate that program-number and bank-number will not be sent when
the preset is called up. The PROGRAM/BANK-button can be used to toggle between "STORE" and "STORENO".
The actual Program-number is set to the desired value (1...128) via the data-entry dial, the Bank-number via the
sliders. The left slider adjusts MIDI-controller #0, the right slider is responsibel for MIDI-controller #32 (data range is
0...127). The messages will be sent via MIDI-OUT using the MIDI-channel and output(s) of the selected keyboard
zone, thus providing immediate feedback to the user with respect to program-number and bank-number.
The display shows in the bottom line the values of Controller #0 (adjusted by left slider), Controller #32 (right slider),
MIDI-channel (in brackets) and Program-number (adjusted via data entry). During a later call-up of a preset the values
for Program, Controller #0 and #32 are transmitted only if STORE is selected for the zone.
Please note that not all expanders (or synthesizers, samplers, etc.) are capable of utilizing the bank-function. If an
instrument controlled via the LMK4 does not have this feature, then the option
cannot be used.
In the sub-menu VOLUME the volume for a keyboard zone is set. Regarding STORE/STORENO the same hints as
for PROGRAM/BANK are valid i.e. one toggles with the VOLUME-button between STORE and STORENO and
activates/deactivates the sending of the volume message for the zone during call-up of a stored preset.
The actual volume is set to the desired level (1...128) via the data-entry dial. It will be sent via MIDI-OUT over the MIDIchannel and MIDI-output of the selected keyboard zone, thus providing immediate feedback to the user with respect
to volume. Please note that especially elder expanders (or synthesizers, samplers, etc.) may not be capable of
utilizing the volume-function. If an instrument controlled via the LMK4 does not have this feature, then the option
cannot be used.
Setting the volume for a keyboard zone has a second meaning: it also determines the maximum volume-level which
can be attained for that zone with any controller. If the volume function is assigned to a controller (Slider, Wheel, Foot
controller etc.) and is activated in the keyboard zone in question, then the range of values for volume data sent for this
zone will be between 0 and the volume-value entered by the user. This is what we call "proportional volume control".
Example: The volume for zone 1 is set to 100, that for zone 2 is set to 70 and that for zone 3 is set to 127. The
volume-values sent (e.g. by an external foot-controller that is activated in zone 1, 2 and 3) for zone 1 will thus be
0...100, those for zone 2 will be 0...70, those for zone 3 will be 0...127 assuming of course that a the controller in
question has been assigned to VOLUME and that the function has been activated for all three zones. This allows
proportional volume-adjustment in different zones with one controller. If the full range of volume-values is desired for all
zones, then the volume must be set to 127 for each zone.
If a keyboard zone is not to be activated (i.e. fewer than 8 keyboard zones are required/desired) the lower and upper
key(s) of the zone(s) are set to zero with the data-entry dial. No MIDI note event data will then be sent into those
zones (note on, note off). However, these zones not used by the keyboard can be utilized to send program-numbers
or volume-data. This may be useful to switch programs e.g. on drum-computers or effect-processors.
If a zone should be completely turned off the "0&0"-function in the CHANNEL-submenu should be used. In this case
no MIDI messages are sent from the zone in question, even no controllers or Program-change.
LMK4 User's Guide Page 14
2.3.5 Controller Assign/Activate (5)
This menu is selected by pressing the fifth MENU-button from the left. The menu has 2 functions.
The first is the assignment of controllers to the standard MIDI-functions ("Assign"- function). The second is the
activation of the controllers in the various keyboard zones ("Activate"-function).
When entering this menu one reaches the "Activate"-portion first. The following message appears on the display:
ZONE : 00Y
CONTR.X ON/OFF
Next to the word "ZONE" appears the number 00Y of the keyboard zone last selected in the SPLIT-menu. The
activation of the controllers in the CONTROLLER ASSIGN/ACTIVATE-menu always refers to the zone previously
selected in the SPLIT-menu.
The BANK-buttons are for the various controllers (i.e. wheels, sliders, data entry, external footcontrollers and
footswitches, aftertouch). The following controllers are allocated to the 8 BANK-buttons (starting on the left and
showing the abbreviations seen on the display):
Spring-loaded modulation wheel
Non-spring-loaded modulation wheel
External variable foot controller 1
External variable foot controller 2
Slider 2
Aftertouch sensor
Slider 1
Rotary potentiometer
WHEEL1
WHEEL2
E.CTR1
E.CTR2
CTR2
ATOUCH
CTR1
CTR3
The NUMBER-buttons are for the switch-controllers (double footswitch). The following controllers are allocated to
these buttons (starting at the left and showing the abbreviations seen on the display):
Footswitch 1
Footswitch 2
EX.SW1
EX.SW2
The other six NUMBER-buttons are not used since the LMK4 only uses the two footswitches above.
If one of the 10 buttons used for controller assignment purposes is pressed the display will show the
abbreviation of the controller on the left of the lower line, followed by an arrow-symbol (->). The function currently
assigned to that controller is also indicated (see below for abbreviations). On the right side of the lower display line
will be the word "ON" or "OFF", depending on whether or not the controller in question is activated in the keyboard
zone currently being worked in. Repeated pressing of the switch representing that particular controller allows for
switching back and forth between "ON" and "OFF". If a footswitch has been assigned to the LINK-function (LNK) one
can activate this function only in zone 1 since it is a global parameter which can not be set differently for the various
keyboard zones. If an attempt is made to activate the LINK-function in zones 2-8, then the message "LINK
IMPOSSIBLE" will appear in the display.
The assignment of a controller to a MIDI-function can NOT be changed in this portion of the menu since it represents
a global parameter for the entire preset, not just for a particular keyboard zone! Pressing the fifth MENU-button again
calls up the "Assign"- portion of the menu. It is here that controllers are assigned to the various MIDI-functions. The
following message appears on the display:
ASSIGN CONTROLLERS
TO MIDI EVENT
These settings, as mentioned above, have global meaning for the entire preset, not just a single keyboard zone. The
assignment of controllers to MIDI-functions is identical for all 8 keyboard zones. As discussed earlier, it is possible to
choose whether or not a controller will be active in a given keyboard zones. This is done in the "Activate"-portion of
this menu.
The 8 BANK-buttons and the 2 leftmost NUMBER-buttons once again represent the same controllers as in the
"Activate"-portion of this menu.
LMK4 User's Guide Page 15
After one of the 10 controllers has been selected, the lower line of the display will once again show that controller's
abbreviation followed by an arrow-symbol (->) and the current assignment to a MIDI-function. The assignment of the
controller can now be changed by means of the data-entry dial.
REMEMBER: The new assignment will be a global parameter for the entire preset!
The following standard MIDI-functions can be assigned to the various controllers (with abbreviations):
Pitch Bend
Portamento
Aftertouch
Data Entry
Modulation
Volume
Breadth-Controller
Panorama
PIT
POR
ATO
ENT
MOD
VOL
BRE
PAN
In addition there are 8 user-defined controllers (UD1...UD8) which are explained in section 2.3.6.
The assignment of the selected controller to a MIDI-function is accomplished by turning the data-entry dial. The
assigned function will appear in the display to the right of the arrow symbol (in abbreviated form). Example: WHEEL1
-> PIT.
The external footswitches can be assigned to the following MIDI-standard-functions (with
abbreviations):
Sustain
Portamento ON/OFF
Soft-Pedal
Sostenuto
Preset-Switchover
SUS
POO
SOF
SOS
LNK
In addition they can be assigned to 3 additional, as yet undefined controllers (FR2...FR4) and the 8 user-defined
controllers (UD1...UD8).
The first 4 functions in the above list are standard MIDI-controllers. The fifth function (LNK=Link) is not a MIDIcontroller. It is the internal switchover function for the 128 LMK4 presets. If the LINK-function is assigned to a
footswitch, then the next preset in the preset-queue will be selected when the footswitch is used (also refer to
PRESET-POINTER-display in menu 1 and PRESET-POINTER-adjustment in menu 7). If, while stepping through the
queue, a preset is selected where the footswitch controls a function other than LINK, then the queue would end here
and the footswitch could no longer switch to the next preset. Instead it would control whatever function has been
assigned to it in this particular preset, for example SUSTAIN.
The assignment of the footswitch to a MIDI-controller or to the LINK-function is accomplished by means of the dataentry dial. The assigned controller-function will appear in abbreviated form next to the arrow symbol in the display.
Example: EX.SW2->SUS.
We would like to point out one more time that the assignment of the controllers and the after-touch sensor to the
various MIDI-functions is identical for all keyboard zones of a preset. It certainly wouldn't make much sense if the
same controller simultaneously had two different functions in two different keyboard zones of the same preset (for
example VOLUME and PITCH BEND).
Since the assignment of controllers to MIDI-functions is done only once for each preset, this particular portion of the
menu was placed behind the activation of the controllers in terms of operational procedure. Controllers are activated
separately for each keyboard zone. If controllers were to be assigned prior to activation, one would have to go through
the assignment menu prior to each activation. This might create the false impression that controllers can be assigned
independently for each keyboard zone.
Note: One should only activate controllers which are actually present and are being used, since otherwise the
possibility of random controller data being sent out exists. For example, if a pedal is assigned to VOLUME in a given
keyboard zone and has been activated even though no pedal is connected to the LMK4, then the volume can go to
some random level while playing. The aftertouch sensor, the two wheels and the sliders should also be activated only
if they are actually utilized in a preset within a given zone. Please avoide to assign two controllers the same function
and activate them in the same zone. For example, if you assign both slider 1 and external controller 2 to the volume
LMK4 User's Guide Page 16
function and activate both in zone 1, there will occur problems because volume can be changed as well with slider 1
as with external controller 2. The result may be jumps in volume or even continuous volume messages alternating
from slider 1 and external controller 2. There would be a constant conflict between the inputs from the two controllers.
If your instrument seems to be sending random data for pitch-bend and/or aftertouch, or seems to be sending
random controller data, please check if 2 controllers have accidentally been assigned to the same function.
A special case is the assignment of of the after-touch-sensor to pitch-bend. There is a global parameter in menu 7
(PARAMETERS), called ATP (Aftertouch-to-Pitch) which determines whether the pressure exerted on the keys has a
positive or negative effect on pitch-bend. Without pressure the pitch-bend value of 64 is sent ($40 Hexadecimal). If
ATP is positive, increasing pressure on the keys causes the pitch-bend values 64...127 ($40...$7F Hex) to be sent; a
negative ATP results in values 64...0 ($40...$00 Hex).
2.3.6 User-Defined MIDI-Controllers
This menu is selected by pressing the sixth MENU-button from the left. It is used to define the 8 user-specific MIDIcontrollers UD1...UD8. The following message appears on the display:
UD-MIDI CONTR.
1/2/3/4/5/6/7/8
The lower line of the message is a symbolic representation of the 8 UD-controllers. They can be activated via the
BANK-buttons. The NUMBER-buttons have no function in this menu. After pressing one of the 8 BANK-buttons the
following message appears on the lower display-line:
USERDEF (00X):YYY
X stands for 1...8, depending on which BANK-button was pressed. YYY represents the controller-number which is to
be assigned to the user-defined controllers UD1..UD8. This number can be adjusted between 0 and 127 with the dataentry dial. The widely used standard MIDI-controller-numbers have already been used for the various standard
controllers (see below). If the instrument connected to the LMK4 uses a special controller-number for a particular
function, then that number can be selected and assigned to a controller here.
Please note that controllers above number 121 represent MIDI-channel-mode messages, for example LOCAL
ON/OFF, ALL NOTES OFF, etc. They should be used with caution.
All user-defined controllers are preset-parameters and are being stored in each preset. Different
UD-controllers can be defined for different presets. The following standard controllers are already being utilized:
CONTR#
FUNCTION (ABBREV.)
REMARKS
1
2
5
6
7
10
Pitch Bend (PIT)
After Touch (ATO)
Modulation (MOD)
Breath Controller (BRE)
Portamento Time (POR)
Data Entry (ENT)
Volume (VOL)
Panorama (PAN)
Intrinsic function, belongs not really to MIDI controllers
Intrinsic function, belongs not really to MIDI controllers
continuous controller
continuous controller
continuous controller
continuous controller
continuous controller
continuous controller
CONTR#
FUNCTION (ABBREV.)
REMARKS
64
65
66
67
Sustain (SUS)
Portamento On/Off (POO)
Sostenuto (SOS)
Soft Pedal (SOF)
switch
switch
switch
switch
controller
controller
controller
controller
The data range for continuous controllers is 0...127, for switch (or digital) controllers 0/127 (only one of the two
values: 0 or 127).
LMK4 User's Guide Page 17
2.3.7 Parameters/Name
This menu is selected by pressing the seventh MENU-button from left. In this menu all those global parameters are
set which would not fit into the other menus. These include the Preset-pointer, the Realtime-instructions during
preset-callup, the ATP-parameter, the velocity-response reduction factor of the black keys, the Preset name,
the manual dump and the Memory transfer from volatile to the non-volatile part after a receive dump. Only the five
leftmost BANK-buttons are used in this menu.
The first is used to adjust the Preset-pointer. This is the number of the next preset activated when presets are
switched over via the footswitch, assuming one of the two footswitches has been assigned to the LINK-function in the
preset presently active (see CONTROLLER ASSIGN/ACTIVATE for details). When the switch is pressed the following
message will appear on the display:
LINK TO PRES > YYY
YYY is the number of the next preset activated when presets are switched over. The number is set to the desired
value via the data-entry dial. It is also possible to form loops since there are no restrictions on the setting of the
preset-pointer. Just remember that one of the footswitches must be assigned to the LINK-function in the preset being
jumped to, otherwise it will be impossible to jump to the next preset via the footswitch.
Note: When pressing the link-footswitch the display will show the new preset number only if the PRESET-menu
(leftmost MENU-button) is selected. If another menu is selected the new preset number is not displayed even though
the new preset is called up.
The second BANK-button from left activates the realtime-instructions (START, STOP, CONTINUE)
when selecting a preset. The following message will appear on the lower line of the display:
REALTIME-MSG : YYY
YYY can be any of the following:
NIX
STA
STO
CNT
No realtime-instruction at preset-selection
START-instruction during preset-selection
STOP-instruction during preset-selection
CONTINUE-instruction during preset-selection
MIDI-clock is stopped
MIDI-clock is sent
MIDI-clock is stopped
MIDI-clock is sent
The data-entry dial is used to select between those four options. If STA or CNT is selected, then the LMK4 will send
the realtime-instruction (STA or CNT) and MIDI-clock-data with the tempo stored in the preset. These instructions are
sent after the up to 8 program-numbers, controllers #0 and #32 (bank) and the volume-values for the 8 keyboard
zones. If NIX or STO is selected no MIDI-clock-signal is sent. If the clock-signal should continue to be sent when a
new preset is selected (without START), then CON must be selected. If the tempo is to be maintained in the new
preset, then the tempo of the new preset must be set to the same value as that of the previous preset. Otherwise a
tempo change will take place when the new preset is selected.
The third BANK-button from left adjusts the velocity-response reduction factor of the black keys. Because of their
shorter leverage the black keys have a higher velocity-response than the white keys, with key pressure being equal.
In this menu item one can set a parameter which reduces the velocity-response of the black keys in comparison to
the white keys. The following will appear on the lower line of the display:
SCALE BLACK: XXX
XXX represents a value between 0...127, to be set with the data-entry dial. 127 means that black and white keys are
being treated equal, 0 would completely suppress the black keys. Experience has shown a value of about 120 to be
best. SCALE BLACK is a global parameter of the LMK4, i.e. it is valid for all presets and does not need to be entered
for each one separately.
The fourth BANK-button manually triggers a dump of the entire content of the preset-memory. The following message
appears on the lower line of the display:
SEND SYS-EX BULK
LMK4 User's Guide Page 18
At the same time the 8 LED's are counting up the presently transmitted preset-numbers in binary form. Triggering the
dump obviously is useful only if an appropriate receiver is present (i.e. sequencer, computer with MIDI-Dump software)
which can store the data and subsequently return it to the LMK4. A more detailed description of the DUMP-function
can be found in the section on the
PRESET-menu.
The fifth BANK-button sets the so-called ATP-parameter, ATP standing for after touch-to-pitch. This parameter
determines if pressure on the keys has a positive or negative effect on pitch-bend when the aftertouch sensor has
been assigned to the pitch-bend function. The following message will appear on the lower line of the display:
ATP/ON+/OFF-: XXX
XXX stands for "ON" or "OFF". The fifth BANK-button can be used to toggle between "ON" and "OFF". "ON" means a
positive effect of key pressure on pitch-bend, "OFF" causes a negative effect. The ATP-parameter is global, i.e. once
set it is valid for all presets stored in the LMK3. Of course the parameter is meaningful only if the aftertouch sensor
has been assigned to the pitch-bend function.
The last BANK-button triggers the Memory transfer from volatile to the non-volatile part after a receive dump. Before
the transfer is performed the following message appears in the display:
STORE ALL PRESETS TO EEPROM?
Also, all 8 LED's will be illuminated as a warning! Only if the BANK-button No. 8 is pressed once again the transfer is
performed. Pressing any other Bank-button stops the process.
The transfer from volatile (RAM) to non-volatile memory (EEPROM) is necessary only after a receive dump from a
editor or dump-program. After the receive dump the data is stored only in the volatile memory section of the LMK4
(RAM). To keep the information after power off the data must be transferred to the non-volatile memory section of the
LMK4 (EEPROM). Normally the transferring program will trigger the memory transfer automatically by sending a
Store-command via MIDI. Only if the program used does not support this feature the manual transfer has to be
performed. The memory transfer process requires about 2 minutes. During this period it is not possible to play on the
keyboard or operate one of the controllers or to receive MIDI data. A message in the display informs about the state
of memory transfer.
Pressing MENU-button 7 once more will select the submenu for naming presets. On the upper line of the display
the current name of the preset is shown. The 8 BANK-buttons correspond to the 8 characters of the name. To change
a character one must press the corresponding BANK-button and then turn the data-entry dial. All capital letters, the
numbers 0 through 9 and some special characters are available.
2.3.8 Panic
This menu is selected by pressing the rightmost MENU-button. The PANIC-function can be used
under any operational conditions. Pressing the PANIC-menu-button while in another menu will cause immediate exit
from that menu.
The PANIC-menu also provides 16 Pseudo-panic-buttons for the 16 MIDI-channels. The BANK-buttons represent
pseudo-panic-buttons 1 through 8, the NUMBER-buttons represent pseudo-panic-buttons 9 through 16, from left to
right. These panic-buttons do not cause an ALL NOTES OFF-instruction to be sent. Instead 128 individual NOTE
OFF-instructions are sent for all 128 possible notes of the MIDI-channel in question. This function is required for MIDIinstruments which do not recognize the ALL NOTES OFF-instruction. Such instruments would not respond to the
'normal' panic-button, since it only provides the ALL NOTES OFF-instruction. A PANIC-function which buttons off all
128 notes on all 16 channels via NOTE OFF-instructions will unfortunately cause MIDI-Overflow in almost all MIDIinstruments. In most cases a message like "MIDI-BUFFER FULL" or similiar would appear on the display. This is
the reason for the introduction of the 16 pseudo-panic-buttons on the LMK4, since they effectively prevent this
problem.
LMK4 User's Guide Page 19
APPENDIX A:
Explanation of the velocity-response curves and aftertouch curves.
When defining the parameters of the keyboard zones one can select among 64 velocity-response
curves and 8 aftertouch curves. In the following paragraph the reasons for this feature shall be discussed briefly.
The special MIDI-chip used inside the LMK2 to poll the key-contacts uses the time difference required by the switchcontact to derive the velocity response (or dynamics-value). The relationship between measured time difference and
velocity is one of inverse proportion, i.e.doubling the time causes the velocity-response to be halved. However, this is
not the response one is used to from a piano. Thus the option of adjusting the keyboard's velocity-response via
response curves was created.
In the case of non-adjusted velocity-response (Curve 1) most people feel that the high values start too early and that
there is insufficient resolution in the lower range. There are several tables which more or less compensate for this.
The higher the number of the table (2...8) the more the velocity-response is moved upward, i.e. the harder one must
press the keys to obtain a given velocity-response. Tables 9...12 represent alternative velocity-response curves, i.e.
the dynamics rise even faster than in the inverse proportional curves. Tables 13...28 contain various linear, logarithmic
and exponential characteristic curves with start- or end-response. Table 16, for example, sends a response value of at
least 16. However, the rise of the response starts only at minimum key-pressure and ends at a maximum value of
100.
Tables 29 and 30 contain reversed characteristic-curves, i.e. the velocity-response values decrease as the keys are
pressed harder. This seemingly illogical feature can be used for key-pressure-controlled blend-over effects
("Crossfade"). For this application one expander (or sound) is controlled with a 'normal' curve (1...28), another with
with a reversed curve (29 or 30). This is done by defining the same UPPER/LOWER key-values for two different
keyboard zones, but using different velocity-response curves and MIDI-channels for those two zones. Depending on
how hard the keys are pressed one expander will now become louder, while the other expander will simultaneously
become more quiet. The velocity-response characteristics will to some extent also depend on the type of expander
being used, since different instruments have different characteristics.
The velocity response curves 33-64 are identical to the curves 1-32 with one little exception. If a key is pressed very
slow the curves 1-32 produce a small velocity value (normally 1) whereas the curves 33-64 will send a velocity value of
0 (this is defined as note off). The main reason for the curves 33-64 is that many expanders produce an audible sound
if they receive a note on event with velocity 1. But this is not the behaviour of a real piano. A real piano will produce no
sound in this case. So if you want to achieve the behaviour of a real piano you have to select one of the velocity
response curves 33-64 rather than 1-32. Therefore the curves 33-64 are called "Piano Mode velocity response curves".
Velocity-response is to some extent also dependant upon the expander being used. There are significant differences
in the characteristics of different expanders. Some expanders also include various velocity-response curves of their
own. The 32 (64) curves included with the LMK4 generally permit sufficiently good adjustment of the velocity-response
characteristics.
The LMK4 also provides 8 aftertouch curves. In general, the same comments apply to these as to the velocityresponse curves. Curve 1 is linear. In curves 2...4 the high aftertouch values appear earlier, meaning that the lower
range of the aftertouch is more sensitive. Curves 5 and 6 have a minimum (5) and a maximum value (6), repectively,
for the aftertouch characteristic. Curve 8 is an inverted function, i.e. the aftertouch value decreases with increasing
pressure on the keys.
Graphical representations of the various curves can be found on the next page.
LMK4 User's Guide Page 20
VELOCITY-RESPONSE CURVES
AFTERTOUCH-RESPONSE CURVES
LMK4 User's Guide Page 21
Appendix B: Pin Assignment of the Jack Sockets
Power Supply
1
"high"
end
2
1 = +7...12V DC
2 = GND
"low"
end
Foot Controller
(EXT.CTRL. 1/2)
2...10k linear
Foot Switches
(SWITCHES)
Switch 2
Switch 1
Appendix C: Conversion table Bank/Numbers to Decimal System
LMK4 User's Guide Page 22
Appendix D: Quick reference table of functions
LMK4 User's Guide Page 23
Appendix E: Resetting all Presets
One must press the two right-hand MENU-buttons simultaneously for several seconds while switching
the keyboard on. The message "LMK3 MES" should then appear on the display, along with
the date of the software version. Use this function very cautiously while operating the LMK3! Any previously entered
preset-values will be irretrievably lost! Use this function only when switching the keyboard on for the first time or if you
wish to erase all presets !
During initialization the following values are entered into the preset memories:
WHOLE KEYBOARD ZONE 1, ONLY ZONE 1 ACTIVE, MIDI-CHANNEL 1, NO TRANSPOSITION,
DYNAMIC TABLE 1, NO CONTROLLERS ACTIVE, NO PROGRAM NUMBERS OR VOLUME
NUMBERS ACTIVE, PRESET-NAME "INITPRES".
Appendix F: Technical Data LMK4+
High quality keyboard with 88 or 76 weighted 'piano-touch' keys
Built into a flight-case with removable lid and snap-closures
2-line, 16-character LC display with adjustable background illumination and contrast
24 function-buttons grouped in three rows of 8 (Top row with LED indicators)
2 Wheels (one spring-loaded), 2 Sliders, 1 Data-entry dial
Monophonic aftertouch (Channel-aftertouch)
External input-jack for double-footswitch
External input-jack for sweep pedal
1 MIDI-OUT
1 MIDI-IN (MIDI-IN only for LMK3-DUMP-function, not suitable for connecting another keyboard)
External power supply
Wheels, sliders, aftertouch sensor, pedal and footswitch can be assigned to any MIDI-function
MIDI-program-change-instructions (1...128) sent on selectable MIDI-channel (MIDI-master-channel)
MIDI-START, STOP, CONTINUE, CLOCK available to control sequencers or drum computers
PANIC-button ("ALL NOTES OFF" on all channels and initialization of all controllers)
All presets selectable in user-defined order via one of the footswitches (i.e. footswitch-activated
preset change)
32 velocity-response curves
8 aftertouch curves
8 user definable controllers (MIDI-Controller # 0...127 can be assigned)
Adjustable velocity-response reduction factor for black keys
DUMP-function (for single presets or the entire preset memory)
Adjustable effect on pitch-bend (positive or negative) when aftertouch-sensor is assigned to
pitch-bend function
Proportional volume control of different keyboard zones with a single controller
64 Keyboard-presets
The following parameters can be adjusted/defined by the user in each preset:
--Assignment of controllers (Wheels, sliders, pedal, external footswitch, etc.) to MIDI-functions (Pitch
bend, modulation, breath contoller, aftertouch, volume, panorama, portamento time, sustain, soft pedal, sostenuto,
portamento ON/OFF and 8 user-defined controllers)
-- Name of the preset (up to 8 characters)
-- Preset tempo (MIDI-clock)
-- Alternative sending of START, STOP or CONTINUE-instruction at time of preset call-up
-- Preset-pointer setting (indicating the number of the preset selected during the next program
change via footswitch; formation of loops possible)
- 8 overlapping keyboard-keyboard zones
The following features can be defined/adjusted by the user in each zone:
-- UPPER/LOWER key
-- MIDI-channel (1...16)
-- Transposition in half-note increments (+/- 63)
-- Selection of one of 32 velocity-response curves for the velocity-response characteristic
-- Selection of one of 8 aftertouch curves for the aftertouch characteristic
-- Selection of controllers to be active within each keyboard zone
-- Program-number and Volume of the keyboard zone (This two messages can be sent on the
MIDI-channel of that zone when a preset is selected, meaning that the correct sound characteristics
and loudness for that zone are immediately established)
LMK4 User's Guide Page 24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement