Product overviews

ew 100 P G3 Set _529660_0309_Sp9.book Seite 4 Mittwoch, 8. April 2009 6:57 18

Product overviews

Product overviews

Overview of the EK 100 G3 diversity receiver

!

"

!

-

%

,

+

$

%

&

'

*

*

)

Operating elements

!

3.5 mm jack socket, lockable ( AF OUT )

(the shielding is used by antenna II)

"

Antenna I

#

Operation and battery status indicator, red LED

(lit = ON /flashing = LOW BATTERY )

$

RF signal indication, green LED

(lit = RF )

%

Charging contacts

(

& SET button

'

!

/

"

rocker button ( UP / DOWN )

(

Battery compartment

)

Battery compartment cover

*

Battery compartment catches

+

Infra-red interface

, ON

/ OFF button

(serves as the ESC (cancel) key in the operating menu)

-

Display panel, backlit in orange

4

ew 100 P G3 Set _529660_0309_Sp9.book Seite 5 Mittwoch, 8. April 2009 6:57 18

Overview of the SK 100 G3 bodypack transmitter

!

!

"

Product overviews

$

+

.

&

-

,

+

*

%

&

'

(

)

Operating elements

!

Microphone/instrument input ( MIC / LINE ),

3.5 mm jack socket, lockable

" MUTE switch

#

Antenna

$

Operation and battery status indicator, red LED

(lit = ON /flashing = LOW BATTERY )

%

Audio overmodulation indicator, yellow LED

(lit = AF PEAK )

&

Charging contacts

' SET button

(

!

/

"

rocker button ( UP / DOWN )

)

Battery compartment

*

Battery compartment cover

+

Battery compartment catches

,

Infra-red interface

- ON

/ OFF button, serves as the ESC (cancel) key in the operating menu

.

Display panel, backlit in orange

5

ew 100 P G3 Set _529660_0309_Sp9.book Seite 10 Mittwoch, 8. April 2009 6:57 18

Putting the devices into operation

Putting the devices into operation

EK 100 G3 diversity receiver

Inserting the batteries/accupack

For powering the diversity receiver, you can either use two 1.5 V AA size batteries or the rechargeable Sennheiser BA 2015 accupack.

#

Open the battery compartment by pushing the two catches

*

in the direction of the arrows and open the cover

)

.

) *

)

%

#

Insert the two batteries or the accupack as shown above. Please observe correct polarity when inserting the batteries/accupack.

#

Close the battery compartment by pressing on the center of the cover

)

.

The battery compartment cover

)

locks into place with an audible click.

Charging the accupack

To charge the BA 2015 accupack:

#

Insert the diversity receiver into the L 2015 charger (optional accessory).

The L 2015 simultaneously charges up to two devices, e.g. two diversity receivers or one diversity receiver and one SK 100 G3 bodypack transmitter.

The L 2015 charger can only charge the BA 2015 accupack. Standard batteries

(primary cells) or individual rechargeable battery cells cannot be charged.

10

ew 100 P G3 Set _529660_0309_Sp9.book Seite 11 Mittwoch, 8. April 2009 6:57 18

Putting the devices into operation

/

.

0

Mounting the diversity receiver to a camera

Use the supplied CA 2 camera adapter to mount the receiver to a camera’s flash mount.

#

Determine where on the perforated plate

.

the flash mount adapter

/

will need to be fastened so that the receiver can best be attached to the camera.

#

At this position, place a square nut

0

under the perforated plate

.

.

#

Fasten the flash mount adapter

/

to the perforated plate

.

using the square nut

0

.

#

Lift one side of the belt clip

1

as shown.

1

#

Press down the belt clip

1

at one fixing point and pull it out of the receiver housing.

#

Repeat for the other side.

#

Place the perforated plate

.

onto the rear of the receiver.

#

Reinsert the belt clip

1

.

#

Use one of the supplied line cables to connect the line input of the camera to the socket

!

.

!

The shield of the line cable serves as the antenna for the second diversity section.

11

ew 100 P G3 Set _529660_0309_Sp9.book Seite 12 Mittwoch, 8. April 2009 6:57 18

Putting the devices into operation

/

!

SK 100 G3 bodypack transmitter

Inserting the batteries/accupack/Charging the accupack

The procedure is the same as for the EK 100 G3 diversity receiver:

To insert the batteries/accupack:

#

Read the chapter “Inserting the batteries/accupack” on page 10.

To charge the accupack:

#

Read the chapter “Charging the accupack” on page 10.

Connecting the microphone cable/line cable

The audio input is designed for the connection of condenser microphones. DC powering of the condenser microphones is via the audio input MIC / LINE

!

(3.5 mm jack socket).

#

Use one of the recommended Sennheiser microphones or the optional CL 2 line cable.

#

Connect the 3.5 mm jack plug

/ from the Sennheiser cable to the 3.5 mm jack socket

MIC / LINE

!

.

#

Lock the 3.5 mm jack plug by screwing down the coupling ring

0 of the cable.

#

Via the operating menu, adjust the sensitivity of the microphone/line input.

0

1

Attaching and positioning the corresponding microphones

ME 2/ME 4

#

Use the microphone clip

1

to attach the microphone to clothing (e.g. tie, lapel).

The ME 2 clip-on microphone (shown on the right in the diagram) has an omni-directional pick-up pattern. It is therefore not necessary to position it precisely.

#

Attach the ME 2 microphone as close as possible to the sound source.

The ME 4 clip-on microphone (shown on the left in the diagram) has a cardioid pick-up pattern.

#

Position the ME 4 microphone so that its sound inlet is directed towards the sound source

(e.g. mouth).

12

ew 100 P G3 Set _529660_0309_Sp9.book Seite 13 Mittwoch, 8. April 2009 6:57 18

Putting the devices into operation

Attaching the bodypack transmitter to clothing

You can use the belt clip

2

to attach the bodypack transmitter to clothing (e.g. belt, waistband).

The belt clip is detachable so that you can also attach the transmitter with the antenna pointing downwards. To do so, withdraw the belt clip

2

from its fixing points and attach it the other way round. The belt clip

2

is secured so that it cannot slide out of its fixing points accidentally.

To detach the belt clip:

#

Lift one side of the belt clip as shown in the diagram on the right-hand side.

#

Press down the belt clip at one fixing point and pull it out of the transmitter housing.

#

Repeat for the other side.

2

#

SKM 100 G3 radio microphone

#

Only hold the radio microphone by its body.

If you touch the antenna of the radio microphone during operation, the transmitter’s range will be considerably reduced!

Inserting the batteries/accupack

For powering the radio microphone, you can either use two 1.5 V AA size batteries or the rechargeable Sennheiser BA 2015 accupack.

#

Unscrew the lower part of the radio microphone from the radio microphone’s body

#

by turning it counterclockwise.

When unscrewing the radio microphone during operation, the muting function is automatically activated. “ MUTE ” appears on the display panel.

When screwing the lower part of the radio microphone back to the radio microphone’s body, the muting is canceled.

#

Slide back the lower part of the radio microphone as far as it will go.

#

Open the battery compartment cover

-

(see page 14).

#

Insert the batteries or the BA 2015 accupack as shown on the battery compartment cover. Observe correct polarity when inserting the batteries/accupack (see page 14).

13

ew 100 P G3 Set _529660_0309_Sp9.book Seite 17 Mittwoch, 8. April 2009 6:57 18

Using the devices

Switching the devices on/off

EK 100 G3 diversity receiver

To switch the diversity receiver on :

#

Push the two battery compartment catches

*

and open the battery compartment cover

)

.

!

,

*

)

*

#

Press the ON / OFF button

,

.

The red ON LED

#

lights up and the standard display “ Frequency/Name ” appears on the display panel.

To switch the diversity receiver off :

#

Press the ON / OFF button

,

until “ OFF ” appears on the display panel.

The red ON LED

#

goes off and the diversity receiver switches off.

When in the operating menu, pressing the ON / OFF button

,

will cancel your entry

(ESC function) and return you to the current standard display.

17

ew 100 P G3 Set _529660_0309_Sp9.book Seite 18 Mittwoch, 8. April 2009 6:57 18

Using the devices

SK 100 G3 bodypack transmitter, SKM 100 G3 radio microphone and

SKP 100 G3 plug-on transmitter

3

+

)

3

,

+

-

+

$

'

3

'

* *

(

To switch your transmitter on (online operation):

SK 100 G3

#

Push the two catches

+ and open the battery compartment cover

*

.

#

Briefly press the ON / OFF button

-

. The bodypack transmitter transmits an

RF signal.

The red ON LED

$

lights up and the standard display “ Frequency/

Name ” appears on the display panel. The transmission icon

3

is displayed.

SKM 100 G3

#

Briefly press the ON / OFF button

,

.

The radio microphone transmits an RF signal.

The red ON LED

)

lights up and the standard display “ Frequency/

Name ” appears on the display panel. The transmission icon

3

is displayed.

SKP 100 G3

#

Briefly press the ON / OFF button

(

.

The plug-on transmitter transmits an RF signal.

The red ON LED

'

lights up and the standard display “ Frequency/

Name ” appears on the display panel. The transmission icon

3

is displayed.

You can switch your transmitter on and deactivate the RF signal on switch-on.

For more information, refer to page 19.

To switch your transmitter off :

#

If necessary, deactivate the lock mode (see page 20).

#

Press the ON / OFF button

-

until “ OFF ”

#

Press the button

,

ON / OFF

until “ OFF ” appears on the display panel.

The display panel turns off. The red ON LED

$ goes off.

appears on the display panel.

The display panel turns off. The red ON LED

) goes off.

#

Press the ON / OFF button

(

until “ OFF ” appears on the display panel.

The display panel turns off. The red ON LED

' goes off.

When in the operating menu, pressing the ON / OFF button will cancel your entry

(ESC function) and return you to the current standard display.

18

ew 100 P G3 Set _529660_0309_Sp9.book Seite 19 Mittwoch, 8. April 2009 6:57 18

Using the devices

To switch your transmitter on and to deactivate the RF signal on switch-on (offline operation):

SK 100 G3

#

Keep the ON / OFF button

-

pressed until

“ RF Mute On?

” appears on the display panel.

#

Press the SET button

'

.

SKM 100 G3

#

Keep the ON / OFF button

,

pressed until

“ RF Mute On?

” appears on the display panel.

#

Press the multi-function switch

+

.

SKP 100 G3

#

Keep the ON / OFF button

(

pressed until

“ RF Mute On?

” appears on the display panel.

#

Press the SET button

*

.

The transmission frequency is displayed but the transmitter does not transmit an

RF signal.

The transmission icon

3

is not displayed.

AF

533.875

MHz

ew100 G3

P

MUTE

3

AF

533.875

MHz

ew100 G3

P

MUTE

3

AF

533.875

MHz

ew100 G3

P

MUTE

3

Use this function to save battery power or to prepare a transmitter for use during live operation without causing interference to existing transmission links.

To activate the RF signal :

#

Briefly press the ON / OFF button

-

.

“ RF Mute Off ” appears on the display panel.

#

Press the SET button

'

.

The transmission icon

3 is displayed again.

#

Briefly press the ON / OFF button

,

.

“ RF Mute Off ” appears on the display panel.

#

Press the multi-function switch

+

.

The transmission icon

3 is displayed again.

#

Briefly press the ON / OFF button

(

.

“ RF Mute Off ” appears on the display panel.

#

Press the SET button

*

.

The transmission icon

3 is displayed again.

Synchronizing a transmitter with the diversity receiver

You can synchronize a suitable transmitter of the ew 100 G3 series with the diversity receiver. During synchronization, the following parameters are transferred to the transmitter:

Setting

“ Frequency Preset ”

“ Name ”

“ Pilot Tone ”

Transferred parameters

Currently set frequency

Freely selectable name currently set on the receiver

Current pilot tone setting of the receiver (“ Inactive ”/“ Active ”)

19

ew 100 P G3 Set _529660_0309_Sp9.book Seite 20 Mittwoch, 8. April 2009 6:57 18

Using the devices

+

To transfer the parameters:

#

Switch the transmitter and the diversity receiver on.

#

On the receiver, call up the “ Sync ” menu item.

“ Sync ” appears on the display panel of the diversity receiver.

#

Place the infra-red interface of the transmitter (see page 5 to page 7) in front of the infra-red interface of the diversity receiver

+

.

The parameters are transferred to the transmitter. When the transfer is completed, “ ” appears on the display panel of the diversity receiver. The receiver then switches back to the current standard display.

To cancel the transfer:

Press the ON/OFF button

,

on the diversity receiver.

“ ” appears on the display panel of the receiver. “ ” also appears if no suitable transmitter was found (wrong frequency range/wrong generation).

Deactivating the lock mode temporarily

You can activate or deactivate the automatic lock mode via the “ Auto Lock ” menu item (see page 23). If the lock mode is activated, you have to temporarily deactivate it In order to be able to operate the devices:

+

&

'

'

(

*

EK 100 G3/SK 100 G3

#

Press the SET button

&

(EK) or

'

(SK).

SKM 100 G3

#

Press the multifunction switch

+

.

“ Locked ” appears on the display panel.

#

Press the rocker button

'

(EK) or

(

(SK).

#

Move the multifunction switch

+ upwards/downwards.

“ Unlock?

” appears on the display panel.

#

Press the button

(SK).

&

SET

(EK) or

'

#

Press the multifunction switch

+

.

The lock mode is temporarily deactivated.

SKP 100 G3

#

Press the SET button

*

.

#

Press the

UP button

%

/

DOWN button

&

.

#

Press the SET button

*

.

%

&

20

ew 100 P G3 Set _529660_0309_Sp9.book Seite 24 Mittwoch, 8. April 2009 6:57 18

Overview of the operating menus

When one of the standard displays is shown on the display panel, you can get into the main menu by pressing the SET button

&

. The extended menu “ Advanced Menu ” and the “ Easy

Setup ” menu can be accessed via the corresponding menu items.

Display

Main menu “Menu”

Sync

Squelch

Easy Setup

Frequency Preset

Name

AF Out

Function of the menu item

Synchronizes a transmitter with the diversity receiver

Adjusts the squelch threshold

Adjustment range: “ Low ”, “ Middle ”, “ High ”, can be switched off

Special function (for servicing purposes only): With the squelch threshold set to “ Low ”, you switch the squelch off by keeping the DOWN rocker button

' pressed for 3 seconds.

If you then press the UP button

'

, you switch the squelch on again.

Scans for unused frequency presets, releases and selects frequency presets

Changes the frequency bank and the channel

Enters a freely selectable name

Adjusts the audio output level

Adjustment range: –30 dB to +12 dB, adjustable in steps of 6 dB

Activates/deactivates the automatic lock mode

Calls up the extended menu “ Advanced Menu ”

Exits the operating menu and returns to the current standard display

Auto Lock

Advanced

Exit

“Easy Setup”

Reset List

Current List

Scan New List

Exit

Releases all locked frequency presets

Selects an unused frequency preset

Automatically scans for unused receiving frequencies (frequency preset scan)

Exits the menu “ Easy Setup ” menu and returns to the main menu

Extended menu “Advanced Menu”

Tune

Pilot Tone

LCD Contrast

Reset

Software Revision

Exit

Sets the receiving frequencies for the frequency bank “ U ”

Sets a channel and a receiving frequency for the frequency bank “ U ”:

#

Select this menu item and call it up by pressing the SET button

& until the channel selection appears.

Activates/deactivates the pilot tone evaluation

Adjusts the contrast of the display panel

Resets the diversity receiver

Displays the current software revision

Exits the extended menu “ Advanced Menu ” and returns to the main menu

24

ew 100 P G3 Set _529660_0309_Sp9.book Seite 25 Mittwoch, 8. April 2009 6:57 18

Overview of the operating menus

SK 100/SKM 100/SKP 100 G3

SK 100 G3

Main menu

“Menu”

Sensitivity

Frequency Preset

Name

Auto Lock

Advanced

Exit

Extended menu

“Advanced Menu”

Tune

Mute Mode

Cable Emulation

Pilot Tone

LCD Contrast

Reset

Software Revision

Exit

SKM 100 G3

Main menu

“Menu”

Sensitivity

Frequency Preset

Name

Auto Lock

Advanced

Exit

Extended menu

“Advanced Menu”

Tune

Pilot Tone

LCD Contrast

Reset

Software Revision

Exit

SKP 100 G3

Main menu

“Menu”

Sensitivity

Frequency Preset

Name

Auto Lock

Advanced

Exit

Display

Main menu “Menu”

Function of the menu item

Sensitivity

Frequency Preset

Name

Auto Lock

Advanced

Exit

Adjusts the sensitivity “ AF ”

Changes the frequency bank and the channel

Enters the transmitter name

Activates/deactivates the automatic lock mode

Calls up the extended menu “ Advanced Menu ”

Exits the operating menu and returns to the current standard display

Extended menu “Advanced Menu”

Tune Sets the transmission frequencies for the frequency bank “ U ”

Sets a channel and a transmission frequency for the frequency bank “ U ”

#

Select this menu item and call it up by pressing the SET button (SK, SKP)/the multi-function switch (SKM) until the channel selection appears.

Mute Mode (SK, SKP only) Sets the mode for the MUTE switch

Cable Emulation (SK only) Emulates guitar cable capacities

Pilot Tone

LCD Contrast

Activates/deactivates the pilot tone transmission

Adjusts the contrast of the display panel

Reset

Software Revision

Exit

Resets the transmitter

Displays the current software revision

Exits the extended menu “ Advanced Menu ” and returns to the main menu

Extended menu

“Advanced Menu”

Tune

Mute Mode

Pilot Tone

LCD Contrast

Reset

Software Revision

Exit

25

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement