90413-F-LED - Lucent Lighting

90413-F-LED - Lucent Lighting
Prospex® Pinhole 90 Fixed downlight for LED50
90413-F-LED
Recessed downlight for all Lucent LED50 modules and with
34mm diameter pinhole aperture with deep regressed lamp
position for minimal glare.
Can be installed into new plaster ceilings for trimless seamless
appearance or into existing plaster or suspended ceilings with
"shadow"gap
Both fixed and accent versions available .
360° rotation and 45° adjustment on accent fixtures.
IP44 versions available.Fixed version only
Trims available with overlap flange for installation into existing
ceilings (suffix "-9000-PBZ" to the reference number when
specifing) and Plaster in kit for seamless flush finish (suffix "9000-PCZ" to the reference number when specifing).
Ref Number:
90413-F-LED-WH
90413-F-LED-BK
Lamp quantity
Lamp
Lamp holder
Lamp wattage
Adjustable
Aperture
Overall dimension
Overall height
Required depth
First fix requirement*
Ceiling cut out
Ceiling thickness
Ingress protection**
Dimming options***
White (RAL 9010)
Black (RAL 9005)
1
LED50 / LED50 Plus
n/a
9-19w
No
34mm Ø
92mm Ø
85mm
110mm
Yes
83mm Ø
20mm MAX
IP20
Phase/DALI/1-10v
Cut out 83mm
Trimmed fixture with 9000-PBZ
www.lucent-lighting.com
Cut out 83mm
Trimless fixture with 9000-PCZ
*First Fix requirement. A choice of two installation kits. Specify:
9000-PBZ for already finished ceilings.
9000-PCZ plaster in kit for seamless installation.
**IP Rating. Tested from underside of the ceiling. For IP44 version add suffix "-IP" to the fixture
reference number.
***Dimming. Whilst Lucent can offer the majority of its luminaires with various dimming options, it
remains the responsibility of the specifier/installer to check and ensure compatibility of any control
equipment used. Additional cabling may be required depending on the dimming protocol specified.
It is the policy of Lucent Lighting to continually review and improve its products and therefore reserve the right to change any details of product or
withdraw specifications without prior notice.
Luminaires designed to comply with EN60598 and all other relevant Standards.
This Specification Sheet supersedes all previous versions
All intellectual property rights pertaining to the product described above and to this document are owned by or licensed to Lucent Lighting UK Ltd.
We reserve our right to take whatever action is necessary to protect those intellectual property rights.
Please notify Lucent Lighting Ltd of any inaccuracies immediately. E&OE
Job/Project Name
Area/Location
Contact Lucent Lighting: e: info@lucent-lighting.com t: +44 (0)20 8442 0880
Fitting Ref
Europe
China
Quantity
Russia
Lucent LED50 Range
Lucent's own range of 50mm diameter LED modules including the LED50
>80CRI and LED50-PLUS >90CRI, LED50-SEVEN, LED50-Ambiance Warm
Dim, all utilising Cree XP-E2 white LED's, and LED50-ONE based on Citizen
COB technology.
Please refer to luminaire Specification sheet for maximum lumen output
that can be used within the fixture.
LED50
LED50 Gen 2 80CRI Module
LED50 Gen2 Order Code
LED Colour
2700K
27
3000K
30
4000K
40
Module Type
LED50/2
LED50 module, RA > 80CRI using 9 x Cree XP-E2 LEDs
A choice of 3 colour temperatures 2700/3000/4000K & 3 Optic angles
18/22/36°.
Max Drive current 500mA, can be under run if required. Dimmable with
correct driver type. For dimming protocols available please consult
Lucent Lighting.
Module with on-board protection against surge and reverse polarity.
Example
Optic Angle
18 18°
22 22°
36 36°
LED50/2- 30- 22
LED50 Plus Gen 2 90CRI Module
LED50 PLUS Gen2 Order Code
LED Colour
2700K
27
3000K
30
4000K
40
Module Type
LED50/2
LED50 Plus module, RA > 90CRI using 9 x Cree XP-E2 LEDs
A choice of 2 colour temperatures 2700/3000 & 3 Optic angles
18/22/36°.
LED50
Plus Gen 2 90CRI Module
Max Drive current 500mA, can be under run if required. Dimmable with
correct driver type. For dimming protocols available please consult
Lucent Lighting.
Module with on-board protection against surge and reverse polarity.
Example
Optic Angle
18 18°
22 22°
36 36°
CRI
90 90CRI
LED50/2- 30- 22- 90
LED50 SEVEN 80CRI Module
LED50 Spot module, RA > 80CRI using 7 x Cree XP-E2 LEDs
A choice of 3 colour temperatures 2700/3000/4000K in a narrow 12° spot
optic and 2 complimentary optics.
Max Drive current 700mA, can be under run if required. Dimmable with
correct driver type. For dimming protocols available please consult
Lucent Lighting.
LED50 Seven Order Code
LED Colour
2700K
3000K
4000K
Optic Angle
12 12°
22 22°
36 36°
27
30
40
Module Type
LED57
Example
LED57 30- 22
LED50 Ambiance WarmDim
www.lucent-lighting.com
LED50 Ambiance WarmDim Order Code
LED Colour
Optic Angle
2700K
27
12 12°
3000K
30
22 22°
36 36°
Module Type
LED50WD
LED50 Ambiance Warm Dim, RA > 80CRI using 6 x Cree XP-E2 & 1 x
XT-E LEDs
A choice of 2 main colour temperatures 2700/3000 dimming to 2200K.
Available in 3 optic angles 19/22/36°
Drive current 700mA, Dimmable with correct driver type. For dimming
protocols available please consult Lucent Lighting.
Example
LED50WD- 30- 22
LED50 ONE 90CRI Module
LED50 ONE, RA > 90CRI using 1 x Citizen COB LED.
A choice of 3 colour temperatures 2700/3000/4000K with a single optic in
two beam angles 24/38°.
Max Drive current 350mA, can be under run if required. Dimmable with
correct driver type. For dimming protocols available please consult
Lucent Lighting.
LED50 ONE Order Code
LED Colour
2700K
27
3000K
30
4000K
40
Module Type
LED51
Example
* Separate die cast plaster in kit for plaster ceilings.
** Tested from ceiling underside. To specify IP54; add '-IP' to end of code.
policy of Lucent
Lighting
to continually
review and
its productsordered/specified).
and therefore reserve the right to change any details of product or
It is the
***
Dimming
options
depend
on driver
(to improve
be separately
withdraw specifications without prior notice.
Some control methods may require additional cabling
LED51-
Optic Angle
24 24°
38 38°
30- 38
Luminaires designed to comply with EN60598 and all other relevant Standards.
This Specification Sheet supersedes all previous versions
All intellectual
property
rights pertaining
to the
described
above and
to this document
are owned
or licensed to Lucent Lighting UK Ltd.
Lucent
reserve
the right
to change
anyproduct
details,
dimensions
colours
etc without
priorbynotice.
We reserve our right to take whatever action is necessary to protect those intellectual property rights.
Please notify Lucent Lighting Ltd of any inaccuracies immediately. E&OE
Job/Project Name
Area/Location
Contact Lucent Lighting: e: info@lucent-lighting.com t: +44 (0)20 8442 0880
Fitting Ref
Quantity
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising